LM4916MMX [NSC]
IC 0.014 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10, MSOP-10, Audio/Video Amplifier;型号: | LM4916MMX |
厂家: | National Semiconductor |
描述: | IC 0.014 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10, MSOP-10, Audio/Video Amplifier 音频放大器 |
文件: | 总18页 (文件大小:652K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
July 2003
LM4916
1.5V, Mono 85mW BTL Output, 14mW Stereo Headphone
Audio Amplifier
General Description
Key Specifications
n Mono-BTL output power
The unity gain stable LM4916 is both a mono differential
output (for bridge-tied loads or BTL) audio power amplifier
and a Single Ended (SE) stereo headphone amplifier. Oper-
ating on a single 1.5V supply, the mono BTL mode delivers
85mW into an 8Ω load at 1% THD+N. In Single Ended stereo
headphone mode, the amplifier delivers 14mW per channel
into a 16Ω load at 1% THD+N.
n
(RL = 8Ω, VDD = 1.5V, THD+N = 1%)
n Stereo Headphone output power
(RL = 16Ω, VDD = 1.5V, THD+N = 1%)
85mW (typ)
n
14mW (typ)
0.02µA (typ)
n Micropower shutdown current
n Supply voltage operating range
n PSRR 1kHz, VDD = 1.5V
<
<
0.9V VDD 2.5V
66dB (typ)
With the LM4916 packaged in the MM and LLP packages,
the customer benefits include low profile and small size.
These packages minimize PCB area and maximizes output
power.
Features
n Single-cell 0.9V to 2.5V battery operation
n BTL mode for mono speaker
n Single ended headphone operation with coupling
capacitors
The LM4916 features circuitry that reduces output transients
("clicks" and "pops") during device turn-on and turn-off, an
externally controlled, low-power consumption, active-low
shutdown mode, and thermal shutdown. Boomer audio
power amplifiers are designed specifically to use few exter-
nal components and provide high quality output power in a
surface mount package.
n Unity-gain stable
n "Click and pop" suppression circuitry
n Active low micropower shutdown
n Low current, active-low mute mode
n Thermal shutdown protection circuitry
Applications
n Portable one-cell audio products
n Portable one-cell electronic devices
Typical Application
20048701
FIGURE 1. Block Diagram
Boomer® is a registered trademark of National Semiconductor Corporation.
© 2003 National Semiconductor Corporation
DS200487
www.national.com
Connection Diagrams
MSOP Package
MSOP Marking
200487F9
Z - Plant Code
X - Date Code
T - Die Traceability
G - Boomer Family
A9 - LM4916MM
20048702
Top View
Order Number LM4916MM
See NS Package Number MUB10A for MSOP
LD Package
LLP Marking
200487G0
Z - Plant Code
XY - Date Code
T - Die Traceability
Bottom Line - Part Number
20048752
Top View
Order Number LM4916LD
See NS Package Number LDA10A
www.national.com
2
Typical Connections
20048703
FIGURE 2. Typical Single Ended Output Configuration Circuit
20048705
FIGURE 3. Typical BTL Speaker Configuration Circuit
3
www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Infrared (15 sec)
220˚C
See AN-450 “Surface Mounting and their Effects on
Product Reliablilty” for other methods of soldering
surface mount devices.
Supply Voltage
3.6V
−65˚C to +150˚C
−0.3V to VDD +0.3V
Internally limited
2000V
Thermal Resistance
Storage Temperature
Input Voltage
θJA (typ) MUB10A
θJA (typ) LDA10A
175˚C/W
73˚C/W
Power Dissipation (Note 2)
ESD Susceptibility(Note 3)
ESD Susceptibility (Note 4)
Junction Temperature
Solder Information
Operating Ratings
Temperature Range
200V
150˚C
TMIN ≤ TA ≤ TMAX
−40˚C ≤ TA ≤ 85˚C
0.9V ≤ VDD ≤ 2.5V
Supply Voltage (Note 10)
Small Outline Package Vapor
Phase (60sec)
215˚C
Electrical Characteristics for the LM4916 (Notes 1, 5)
The following specifications apply for the circuit shown in Figure 4 operating with VDD = 1. 5V, unless otherwise
specified. Limits apply for TA = 25˚C.
Symbol
Parameter
Conditions
LM4916
Units
(Limits)
Typical
Limit
(Note 7)
0.9
(Note 6)
VDD
Supply Voltage (Notes 10, 11)
V (min)
V (max)
2.5
∞
IDD
ISD
Quiescent Power Supply Current VIN = 0V, IO = 0A, RL
=
(Note 8)
1.0
0.02
5
1.4
mA (max)
µA (max)
mV (max)
Shutdown Current
VSHUTDOWN = GND
BTL
VOS
Output Offset Voltage
50
70
f = 1kHz
PO
Output Power (Note 9)
RL = 8Ω BTL, THD+N = 1%
RL = 16Ω SE, THD+N = 1%
RL = 8Ω, BTL, PO = 25mW, f = 1kHz
RL = 16Ω, SE, PO = 5mW, f = 1kHz
20Hz to 20kHz, A-weighted
VMUTE = 0, SE
85
14
0.1
0.2
10
15
55
mW (min)
mW
THD+N Total Harmonic Distortion + Noise
0.5
%
VNO
Output Voltage Noise
Mute Current
µVRMS
µA
IMUTE
Crosstalk
RL = 16Ω, SE
dB (min)
VRIPPLE = 200mVP-P
CBYPASS = 4.7µF, RL = 8Ω
f = 1kHz, BTL
62
66
dB
PSRR
Power Supply Rejection Ratio
VRIPPLE = 200mVP-P sine wave
CBYPASS = 4.7µF, RL = 16Ω
f = 1kHz, SE
dB (min)
VIH
VIL
Control Logic High
Control Logic Low
0.7
0.3
V (min)
V (max)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 2: The maximum power dissipation is dictated by T
, θ , and the ambient temperature T and must be derated at elevated temperatures. The maximum
JMAX JA
A
allowable power dissipation is P
= (T
− T )/θ . For the LM4916, T
= 150˚C. For the θ s, please see the Application Information section or the
DMAX
JMAX
A
JA
JMAX
JA
Absolute Maximum Ratings section.
Note 3: Human body model, 100pF discharged through a 1.5kΩ resistor.
Note 4: Machine model, 220pF–240pF discharged through all pins.
Note 5: All voltages are measured with respect to the ground (GND) pins unless otherwise specified.
Note 6: Typicals are measured at 25˚C and represent the parametric norm.
Note 7: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 8: The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier.
Note 9: Output power is measured at the device terminals.
www.national.com
4
Note 10: When operating on a power supply voltage of 0.9V, the LM4916 willl not function below 0˚C. At a power supply voltage of 1V or greater, the LM4916 will
operate down to -40˚C.
Note 11: Ripple on power supply line should not exceed 400mV
.
pp
Typical Performance Characteristics
THD+N
vs Frequency
THD+N vs Frequency
VDD = 1.5V, PO = 5mW, RL = 16Ω
VDD = 1.5V, RL = 8Ω, PO = 25mW
<
BW 80kHz, Single Ended Output
BTL Output, AV = -1
200487C2
200487D5
THD+N
vs Frequency
THD+N
vs Frequency
VDD = 1.2V, PO = 5mW
RL = 16Ω, Single Ended Output, AV = -1
VDD = 1.2V, RL = 8Ω, PO = 25mW
BTL Output, AV = -1
200487D0
200487D6
5
www.national.com
Typical Performance Characteristics (Continued)
THD+N
THD+N
vs Output Power
vs Output Power
VDD = 1.5V, RL = 16Ω, f = 1kHz
Single Ended Output, AV = -1
VDD = 1.5V, RL = 8Ω, f = 1kHz
BTL Output, AV = -1
200487D7
200487D8
THD+N
THD+N
vs Output Power
vs Output Power
VDD = 1.2V, RL = 16Ω, f = 1kHz
Single Ended Output, AV = -1
VDD = 1.2V, RL = 8Ω, f = 1kHz
BTL Output, AV = -1
200487D9
200487E0
Output Power
vs Supply Voltage
f = 1kHz, RL = 16Ω,
Output Power
vs Supply Voltage
f = 1kHz, RL = 8Ω,
BTL Output, AV = -1
Single Ended Output, AV = -1
200487G1
200487G2
www.national.com
6
Typical Performance Characteristics (Continued)
Output Power
vs Load Resistance
Output Power
vs Load Resistance
VDD = 1.5V, RL = 16Ω, f = 1kHz
Single Ended Output, AV = -1
VDD = 1.5V, RL = 8Ω, f = 1kHz
BTL Output, AV = -1
200487E6
200487E5
Output Power
vs Load Resistance
Output Power
vs Load Resistance
VDD = 1.2V, RL = 16Ω, f = 1kHz
Single Ended Output, AV = -1
VDD = 1.2V, RL = 8Ω, f = 1kHz
BTL Output, AV = -1
200487E4
200487E3
Power Dissipation
vs Output Power
Power Dissipation
vs Output Power
<
<
f = 1kHz, THD+N 1%, AV = -1
f = 1kHz, THD+N 1%
Single Ended Output, Both Channels
BTL Output, AV = -1
200487F5
200487F6
7
www.national.com
Typical Performance Characteristics (Continued)
Channel Separation
RL = 16Ω, PO = 5mW
Single Ended Output, AV = -1
Power Supply Rejection Ratio
VDD = 1.5V, VRIPPLE = 200mVPP
RL = 16Ω, Single Ended Output
Input Terminated into 10Ω
200487D4
200487C6
Power Supply Rejection Ratio
VDD = 1.2V, VRIPPLE = 200mVPP
RL = 16Ω, Single Ended Output
Input Terminated into 10Ω
Power Supply Rejection Ratio
VDD = 1.5V, VRIPPLE = 200mVPP
RL = 8Ω, BTL
Input Terminated into 10Ω
200487C5
200487C8
www.national.com
8
Typical Performance Characteristics (Continued)
Power Supply Rejection Ratio
VDD = 1.2V, VRIPPLE = 200mVPP
RL = 8Ω, BTL
Frequency Response
vs Input Capacitor Size
VDD = 1.5V, RL = 16Ω
<
Input Terminated into 10Ω
AV = -1, BW 80kHz, Single Ended Output
200487F8
200487C7
Frequency Response
vs Input Capacitor Size
VDD = 1.5V, RL = 8Ω
Open Loop Frequency Response
VDD = 1.5V, No load
<
AV = -1, BW 80kHz, BTL Output
200487B8
200487C4
Supply Voltage
vs Supply Current
Clipping Voltage
vs Supply Voltage
200487E2
200487F1
9
www.national.com
Typical Performance Characteristics (Continued)
Noise Floor
Noise Floor
VDD = 1.5V, Single Ended Output
16Ω, 80kHz Bandwith
VDD = 1.5V, BTL Output
8Ω, 80kHz Bandwith
200487C3
200487B7
Shutdown Hystresis Voltage
VDD = 1.5V
Power Derating Curve
VDD = 1.5V
200487F4
200487E1
www.national.com
10
Typical Performance Characteristics (Continued)
Mute Attenuation
vs Load Resistance
Shutdown Current
Distribution
200487F2
200487F7
bridge amplifier design has a few distinct advantages over
the single-ended configuration. It provides a differential drive
to the load, thus doubling output swing for a specified supply
voltage. Four times the output power is possible as com-
pared to a single-ended amplifier under the same conditions.
This increase in attainable output power assumes that the
amplifier is not current limited or clipped. In order to choose
an amplifier’s closed-loop gain without causing excessive
clipping, please refer to the Audio Power Amplifier Design
section.
Application Information
SINGLE ENDED (SE) CONFIGURATION EXPLANATION
As shown in Figure 2, the LM4916 has two operational
amplifiers internally, which have externally configurable gain.
The closed loop gain of the two configurable amplifiers is set
by selecting the ratio of Rf to Ri. Consequently, the gain for
each channel of the IC is
AVD = -(Rf / Ri)
A bridge configuration, such as the one used in LM4916,
also creates a second advantage over single-ended amplifi-
ers. Since the differential outputs, Vo1 and Vo2, are biased
at half-supply, no net DC voltage exists across the load. This
eliminates the need for an output coupling capacitor which is
required in a single supply, single-ended amplifier configura-
tion.
When the LM4916 operates in Single Ended mode, coupling
capacitors are used on each output (VoA and VoB) and the
SE/BTL pin (Pin 8) is connected to ground. These output
coupling capacitors blocks the half supply voltage to which
the output amplifiers are typically biased and couples the
audio signal to the headphones or other single-ended (SE)
loads. The signal return to circuit ground is through the
headphone jack’s sleeve.
MODE SELECT DETAIL
The LM4916 can be configured in either Single Ended or
BTL mode (see Figure 2 and Figure 3). The default state of
the LM4916 at power up is single ended. During initial power
up or return from shutdown, the LM4916 must detect the
correct mode of operation by sensing the status of the
SE/BTL pin. When the bias voltage of the part ramps up to
60mV (as seen on the Bypass pin), an internal comparator
detects the status of SE/BTL; and at 10mV, latches that
value in place. Ramp up of the bias voltage will proceed at a
different rate from this point on depending upon operating
mode. BTL mode will ramp up about 11 times faster than
Single Ended mode. Shutdown is not a valid command
during this time period (TWU) and should not enabled to
ensure a proper power on reset (POR) signal. In addition,
the slew rate of VDD must be greater than 2.5V/ms to ensure
reliable POR. Recommended power up timing is shown in
Figure 5 along with proper usage of Shutdown and Mute.
The mode-select circuit is suspended during CB discharge
time. The circuit shown in Figure 4 presents an applications
solution to the problem of using different supply voltages
with different turn-on times in a system with the LM4916.
This circuit shows the LM4916 with a 25-50kΩ. Pull-up re-
sistor connected from the shutdown pin to VDD. The shut-
BRIDGED (BTL) CONFIGURATION EXPLANATION
As shown in Figure 3, the LM4916 has two internal opera-
tional amplifiers. The first amplifier’s gain is externally con-
figurable, while the second amplifier should be externally
fixed in a unity-gain, inverting configuration. The closed-loop
gain of the first amplifier is set by selecting the ratio of Rf to
Riwhile the second amplifier’s gain should be fixed by the
two external 20kΩ resistors. Figure 3 shows that the output
of amplifier one serves as the input to amplifier two which
results in both amplifiers producing signals identical in mag-
nitude, but out of phase by 180˚. Consequently, the differen-
tial gain for the IC is
AVD = 2 *(Rf / Ri).
By driving the load differentially through outputs Vo1 and
Vo2, an amplifier configuration commonly referred to as
"bridged mode" is established. Bridged mode operation is
different from the classical single-ended amplifier configura-
tion where one side of the load is connected to ground. A
11
www.national.com
ers up first) or allows shutdown to ramp up with VDD (the
LM4916 powers up first). This will ensure the LM4916 pow-
ers up properly and enters the correct mode of operation.
Please note that the SE/BTL pin (Pin 8) should be tied to
GND for Single Ended mode, and to VDD for BTL mode.
Application Information (Continued)
down pin of the LM4916 is also being driven by an open
drain output of an external microcontroller on a separate
supply. This circuit ensures that shutdown is disabled when
powering up the LM4916 by either allowing shutdown to be
high before the LM4916 powers on (the microcontroller pow-
20048753
FIGURE 4. Recommended Circuit for Different Supply Turn-On Timing
www.national.com
12
Application Information (Continued)
20048754
FIGURE 5. Turn-On, Shutdown, and Mute Timing for Cap-Coupled Mode
POWER DISSIPATION
The maximum power dissipation point obtained from either
Equations 1, 2 must not be greater than the power dissipa-
tion that results from Equation 3:
Power dissipation is a major concern when designing a
successful amplifier, whether the amplifier is bridged or
single-ended. A direct consequence of the increased power
delivered to the load by a bridge amplifier is an increase in
internal power dissipation. Since the LM4916 has two opera-
tional amplifiers in one package, the maximum internal
power dissipation is 4 times that of a single-ended amplifier.
The maximum power dissipation for a given BTL application
can be derived from the power dissipation graphs or from
Equation 1.
PDMAX = (TJMAX - TA) / θJA
(3)
For package MUB10A, θJA = 175˚C/W. TJMAX = 150˚C for
the LM4916. Depending on the ambient temperature, TA, of
the system surroundings, Equation 3 can be used to find the
maximum internal power dissipation supported by the IC
packaging. If the result of Equation 1 or 2 is greater than that
of Equation 3, then either the supply voltage must be de-
creased, the load impedance increased or TA reduced. For
the typical application of a 1.5V power supply, with a 16Ω
load, the maximum ambient temperature possible without
violating the maximum junction temperature is approximately
146˚C provided that device operation is around the maxi-
mum power dissipation point. Thus, for typical applications,
power dissipation is not an issue. Power dissipation is a
function of output power and thus, if typical operation is not
around the maximum power dissipation point, the ambient
temperature may be increased accordingly. Refer to the
Typical Performance Characteristics curves for power dissi-
pation information for lower output powers.
2
PDMAX = 4*(VDD
)
/ (2π2RL)
(1)
When operating in Single Ended mode, Equation 2 states
the maximum power dissipation point for a single-ended
amplifier operating at a given supply voltage and driving a
specified output load.
2
PDMAX = (VDD
)
/ (2π2RL)
(2)
Since the LM4916 has two operational amplifiers in one
package, the maximum internal power dissipation point is
twice that of the number that results from Equation 2. From
Equation 2, assuming a 1.5V power supply and a 16Ω load,
the maximum power dissipation point is 7mW per amplifier.
Thus the maximum package dissipation point is 14mW.
13
www.national.com
tivation techniques match those given for the shutdown func-
tion as well. Mute may not appear to function when the
LM4916 is used to drive high impedance loads. This is
because the LM4916 relies on a typical headphone load
(16-32Ω) to reduce input signal feed-through through the
input and feedback resistors. Mute attenuation can thus be
calculated by the following formula:
Application Information (Continued)
EXPOSED-DAP PACKAGE PCB MOUNTING
CONSIDERATIONS
The LM4916’s exposed-DAP (die attach paddle) package
(LD) provides a low thermal resistance between the die and
the PCB to which the part is mounted and soldered. This
allows rapid heat transfer from the die to the surrounding
PCB copper traces, ground plane, and surrounding air.
Mute Attenuation (dB) = 20Log[RL / (Ri+RF)]
The LD package should have its DAP soldered to a copper
pad on the PCB. The DAP’s PCB copper pad may be con-
nected to a large plane of continuous unbroken copper. This
plane forms a thermal mass, heat sink, and radiation area.
Further detailed and specific information concerning PCB
layout, fabrication, and mounting an LD (LLP) package is
available from National Semiconductor’s Package Engineer-
ing Group under application note AN1187.
Parallel load resistance may be necessary to achieve satis-
factory mute levels when the application load is known to be
high impedance. The mute function, described above, is not
necessary when the LM4916 is operating in BTL mode since
the shutdown function operates quickly in BTL mode with
less power consumption than mute. In these modes, the
Mute signal is equivalent to the Shutdown signal. Mute may
be enabled during shutdown transitions, but should not be
toggled for a brief period immediately after exiting or entering
shutdown. These brief time periods are labeled X1 (time
after returning from shutdown) and X2 (time after entering
shutdown) and are shown in the timing diagram given in
Figure 5. X1 occurs immediately following a return from
shutdown (TWU) and lasts 40ms 25%. X2 occurs after the
part is placed in shutdown and the decay of the bias voltage
has occurred (2.2*250k*CB) and lasts for 100ms 25%. The
timing of these transition periods relative to X1 and X2 is also
shown in Figure 5. While in single ended mode, mute should
not be toggled during these time periods, but may be toggled
during the shutdown transitions or any other time the part is
in normal operation. Failure to operate mute correctly may
result in much higher click and pop values or failure of the
device to mute at all.
POWER SUPPLY BYPASSING
As with any amplifier, proper supply bypassing is important
for low noise performance and high power supply rejection.
The capacitor location on the power supply pins should be
as close to the device as possible. Typical applications em-
ploy a battery (or 1.5V regulator) with 10µF tantalum or
electrolytic capacitor and a ceramic bypass capacitor that
aid in supply stability. This does not eliminate the need for
bypassing the supply nodes of the LM4916. A bypass ca-
pacitor value in the range of 0.1µF to 1µF is recommended.
MICRO POWER SHUTDOWN
The voltage applied to the SHUTDOWN pin controls the
LM4916’s shutdown function. Activate micro-power shut-
down by applying a logic-low voltage to the SHUTDOWN
pin. When active, the LM4916’s micro-power shutdown fea-
ture turns off the amplifier’s bias circuitry, reducing the sup-
ply current. The trigger point varies depending on supply
voltage and is shown in the Shutdown Hysteresis Voltage
graphs in the Typical Performance Characteristics section.
The low 0.02µA (typ) shutdown current is achieved by ap-
plying a voltage that is as near as ground as possible to the
SHUTDOWN pin. A voltage that is higher than ground may
increase the shutdown current. There are a few ways to
control the micro-power shutdown. These include using a
single-pole, single-throw switch, a microprocessor, or a mi-
crocontroller. When using a switch, connect an external
100kΩ pull-up resistor between the SHUTDOWN pin and
VDD. Connect the switch between the SHUTDOWN pin and
ground. Select normal amplifier operation by opening the
switch. Closing the switch connects the SHUTDOWN pin to
ground, activating micro-power shutdown. The switch and
resistor guarantee that the SHUTDOWN pin will not float.
This prevents unwanted state changes. In a system with a
microprocessor or microcontroller, use a digital output to
apply the control voltage to the SHUTDOWN pin. Driving the
SHUTDOWN pin with active circuitry eliminates the pull-up
resistor.
PROPER SELECTION OF EXTERNAL COMPONENTS
Proper selection of external components in applications us-
ing integrated power amplifiers is critical to optimize device
and system performance. While the LM4916 is tolerant of
external component combinations, consideration to compo-
nent values must be used to maximize overall system qual-
ity. The LM4916 is unity-gain stable that gives the designer
maximum system flexibility. The LM4916 should be used in
low gain configurations to minimize THD+N values, and
maximize the signal to noise ratio. Low gain configurations
require large input signals to obtain a given output power.
Input signals equal to or greater than 1Vrms are available
from sources such as audio codecs. Very large values
should not be used for the gain-setting resistors. Values for
Ri and Rf should be less than 1MΩ. Please refer to the
section, Audio Power Amplifier Design, for a more complete
explanation of proper gain selection. Besides gain, one of
the major considerations is the closed-loop bandwidth of the
amplifier. To a large extent, the bandwidth is dictated by the
choice of external components shown in Figures 2 and 3.
The input coupling capacitor, Ci, forms a first order high pass
filter that limits low frequency response. This value should be
chosen based on needed frequency response and turn-on
time.
MUTE
When in single ended mode, the LM4916 also features a
mute function that enables extremely fast turn-on/turn-off
with a minimum of output pop and click with a low current
consumption (≤20µA, typical). The mute function leaves the
outputs at their bias level, thus resulting in higher power
consumption than shutdown mode, but also provides much
faster turn on/off times. Providing a logic low signal on the
MUTE pin enables mute mode. Threshold voltages and ac-
SELECTION OF INPUT CAPACITOR SIZE
Amplifying the lowest audio frequencies requires a high
value input coupling capacitor, Ci. A high value capacitor can
be expensive and may compromise space efficiency in por-
table designs. In many cases, however, the headphones
used in portable systems have little ability to reproduce
signals below 60Hz. Applications using headphones with this
www.national.com
14
Single-Ended
Application Information (Continued)
CB(µF)
0.1
TON
limited frequency response reap little improvement by using
a high value input capacitor. In addition to system cost and
size, turn on time is affected by the size of the input coupling
capacitor Ci. A larger input coupling capacitor requires more
charge to reach its quiescent DC voltage. This charge
comes from the output via the feedback. Thus, by minimizing
the capacitor size based on necessary low frequency re-
sponse, turn-on time can be minimized. A small value of Ci
(in the range of 0.1µF to 0.47µF), is recommended.
117ms
179ms
310ms
552ms
1.14s
2.4s
0.22
0.47
1.0
2.2
4.7
Bypass Capacitor Value Selection
BTL
Besides minimizing the input capacitor size, careful consid-
eration should be paid to value of CB, the capacitor con-
nected to the BYPASS pin. Since CB determines how fast
the LM4916 settles to quiescent operation, its value is critical
when minimizing turn-on pops. The slower the LM4916’s
CB(µF)
0.1
TON (ms)
72
0.22
0.47
1.0
79
89
outputs ramp to their quiescent DC voltage (nominally VDD
/
112
2), the smaller the turn-on pop. Choosing CB equal to 4.7µF
along with a small value of Ci (in the range of 0.1µF to
0.47µF), produces a click-less and pop-less shutdown func-
tion. As discussed above, choosing Ci no larger than neces-
sary for the desired bandwidth helps minimize clicks and
pops. This ensures that output transients are eliminated
when power is first applied or the LM4916 resumes opera-
tion after shutdown.
2.2
163
283
4.7
In order to eliminate "clicks and pops", all capacitors must be
discharged before turn-on. Rapidly switching VDD may not
allow the capacitors to fully discharge, which may cause
"clicks and pops".
AUDIO POWER AMPLIFIER DESIGN
Minimizing External Components
Operating the LM4916 at higher gain settings can minimize
the use of external components. For instance, a BTL con-
A 25mW/32Ω Audio Amplifier
>
figuration with a gain setting greater than 8V/V (AV
makes the output capacitor CO unnecessary. For the Single
8)
Given:
Power Output
Load Impedance
Input Level
10mWrms
16Ω
>
Ended configuration, a gain setting greater than 4V/V (AV
4) eliminates the need for output capacitor CO2 and output
resistor RO, on each output channel.
0.4Vrms
<
If the LM4916 is operating with a lower gain setting (AV 4),
Input Impedance
20kΩ
external components can be further minimized only in Single
Ended mode. For each channel, output capacitor (CO2 ) and
output resistor (RO) can be eliminated. These components
need to be compensated for by adding a 7.5kΩ resistor (RC)
between the input pin and ground pin on each channel
(between Pin 1 and GND, and between Pin 5 and GND).
A designer must first choose a mode of operation (SE or
BTL) and determine the minimum supply rail to obtain the
specified output power. By extrapolating from the Output
Power vs. Supply Voltage graphs in the Typical Performance
Characteristics section, the supply rail can be easily found.
1.5V is a standard voltage in most applications, it is chosen
for the supply rail. Extra supply voltage creates headroom
that allows the LM4916 to reproduce peak in excess of
10mW without producing audible distortion. At this time, the
designer must make sure that the power supply choice along
with the output impedance does not violate the conditions
explained in the Power Dissipation section. Once the power
dissipation equations have been addressed, the required
gain can be determined from Equation 2.
OPTIMIZING CLICK AND POP REDUCTION
PERFORMANCE
The LM4916 contains circuitry that eliminates turn-on and
shutdown transients ("clicks and pops"). For this discussion,
turn-on refers to either applying the power supply voltage or
when the micro-power shutdown mode is deactivated.
As the VDD/2 voltage present at the BYPASS pin ramps to its
final value, the LM4916’s internal amplifiers are configured
as unity gain buffers. An internal current source charges the
capacitor connected between the BYPASS pin and GND in a
controlled, linear manner. Ideally, the input and outputs track
the voltage applied to the BYPASS pin. The gain of the
internal amplifiers remains unity until the voltage on the
bypass pin reaches VDD/2. As soon as the voltage on the
bypass pin is stable, the device becomes fully operational
and the amplifier outputs are reconnected to their respective
output pins. Although the BYPASS pin current cannot be
modified, changing the size of CB alters the device’s turn-on
time. There is a linear relationship between the size of CB
and the turn-on time. Here are some typical turn-on times for
various values of CB:
(4)
From Equation 4, the minimum AV is 1; use AV = 1. Since the
desired input impedance is 20k, and with a AV gain of 1, a
ratio of 1:1 results from Equation 1 for Rf to R. The values
are chosen with Ri = 20k and Rf = 20k. The final design step
is to address the bandwidth requirements which must be
stated as a pair of -3dB frequency points. Five times away
from a -3dB point is 0.17dB down from passband response
which is better than the required 0.25dB specified.
15
www.national.com
Ci ≥ 1 / (2π * 20kΩ * 20Hz) = 0.397µF; use 0.39µF.
Application Information (Continued)
fL = 100Hz/5 = 20Hz
The high frequency pole is determined by the product of the
desired frequency pole, fH, and the differential gain, AV. With
an AVV = 1 and fH = 100kHz, the resulting GBWP = 100kHz
which is much smaller than the LM4916 GBWP of 3MHz.
This example displays that if a designer has a need to design
an amplifier with higher differential gain, the LM4916 can still
be used without running into bandwidth limitations.
fH = 20kHz * 5 = 100kHz
As stated in the External Components section, Ri in con-
junction with Ci creates a
www.national.com
16
Physical Dimensions inches (millimeters)
unless otherwise noted
MSOP Package
Order Number LM4916MM
NS Package Number MUB10A
17
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
LD Package
Order Number LM4916LD
NS Package Number LDA10A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
©2020 ICPDF网 联系我们和版权申明