LP3875EMPX-ADJ/NOPB [NSC]
IC VREG ADJUSTABLE POSITIVE LDO REGULATOR, 0.55 V DROPOUT, PDSO5, ROHS COMPLIANT, SOT-223, 5 PIN, Adjustable Positive Single Output LDO Regulator;型号: | LP3875EMPX-ADJ/NOPB |
厂家: | National Semiconductor |
描述: | IC VREG ADJUSTABLE POSITIVE LDO REGULATOR, 0.55 V DROPOUT, PDSO5, ROHS COMPLIANT, SOT-223, 5 PIN, Adjustable Positive Single Output LDO Regulator 光电二极管 输出元件 调节器 |
文件: | 总15页 (文件大小:683K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
September 2006
LP3875-ADJ
1.5A Fast Ultra Low Dropout Linear Regulators
General Description
Features
n Ultra low dropout voltage
n Low ground pin current
n Load regulation of 0.06%
The LP3875-ADJ fast ultra low-dropout linear regulators op-
erate from a +2.5V to +7.0V input supply. These ultra low
dropout linear regulators respond very quickly to step
changes in load, which makes them suitable for low voltage
microprocessor applications. The LP3875-ADJ is developed
on a CMOS process which allows low quiescent current
operation independent of output load current. This CMOS
process also allows the LP3875-ADJ to operate under ex-
tremely low dropout conditions.
n 10nA quiescent current in shutdown mode
n Guaranteed output current of 1.5A DC
n Available in TO-263, TO-220 and SOT-223 packages
n Minimum output capacitor requirements
n Overtemperature/overcurrent protection
n −40˚C to +125˚C junction temperature range
Dropout Voltage: Ultra low dropout voltage; typically 38mV
at 150mA load current and 380mV at 1.5A load current.
Applications
Ground Pin Current: Typically 6mA at 1.5A load current.
n Microprocessor power supplies
n GTL, GTL+, BTL, and SSTL bus terminators
n Power supplies for DSPs
n SCSI terminator
Shutdown Mode: Typically 10nA quiescent current when
the shutdown pin is pulled low.
Adjustable Output Voltage: The output voltage may be
programmed via two external resistors.
n Post regulators
n High efficiency linear regulators
n Battery chargers
n Other battery powered applications
Typical Application Circuit
20074645
*See Application Hints
© 2006 National Semiconductor Corporation
DS200746
www.national.com
Connection Diagrams
20074605
20074606
Top View
Top View
TO220-5 Package
Bent, Staggered Leads
TO263-5 Package
20074681
Top View
SOT223-5 Package
Pin Description for TO220-5 and TO263-5 Packages
LP3875-ADJ
Pin #
Name
SD
Function
1
2
3
4
5
Shutdown
VIN
Input Supply
Ground
GND
VOUT
ADJ
Output Voltage
Set Output Voltage
Pin Description for SOT223-5 Package
LP3875-ADJ
Shutdown
Pin #
Name
Function
1
2
3
4
5
SD
VIN
Input Supply
Output Voltage
Set Output Voltage
Ground
VOUT
ADJ
GND
www.national.com
2
Ordering Information
20074631
Package Type Designator is "T" for TO220 package, "S" for TO263 package, and "MP" for SOT-223 package.
TABLE 1. Package Marking and Ordering Information
Description
Output
Voltage
Order Number
LP3875EMP-ADJ
LP3875EMPX-ADJ
(Current,
Option)
Package Type
SOT223-5
Package Marking
LHSB
Supplied As:
ADJ
1.5A, Adj
1000 Units on Tape
and Reel
ADJ
1.5A, Adj
SOT223-5
LHSB
2000 Units on Tape
and Reel
ADJ
ADJ
ADJ
LP3875ES-ADJ
LP3875ESX-ADJ
LP3875ET-ADJ
1.5A, Adj
1.5A, Adj
1.5A, Adj
TO263-5
TO263-5
TO220-5
LP3875ES-ADJ
LP3875ES-ADJ
LP3875ET-ADJ
Rail
Tape and Reel
Rail
3
www.national.com
Block Diagram
LP3875-ADJ
20074629
www.national.com
4
Absolute Maximum Ratings (Note 1)
IOUT (Survival)
Short Circuit Protected
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Operating Ratings
Input Supply Voltage (Operating),
(Note 10)
Storage Temperature Range
Lead Temperature
−65˚C to +150˚C
2.5V to 7.0V
(Soldering, 5 sec.)
260˚C
2 kV
Shutdown Input Voltage
(Operating)
ESD Rating (Note 3)
Power Dissipation (Note 2)
Input Supply Voltage (Survival)
Shutdown Input Voltage
(Survival)
−0.3V to 7.0V
1.5A
Internally Limited
−0.3V to +7.5V
Maximum Operating Current (DC)
Operating Junction Temp. Range
−40˚C to +125˚C
−0.3V to +7.5V
−0.3V to +6.0V
Output Voltage (Survival), (Note
6), (Note 7)
Electrical Characteristics
LP3875-ADJ
Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 10µF, VSD = 2V.
Symbol
Parameter
Conditions
Typ
LP3875-ADJ
Units
(Note 4)
(Note 5)
Min
Max
1.234
1.253
VOUT +1V ≤ VIN ≤ 7V
10 mA ≤ IL ≤ 1.5A
1.198
VADJ
Adjust Pin Voltage
1.216
10
V
1.180
VOUT +1V ≤ VIN≤ 7V
10 mA ≤ IL ≤ 1.5A
IADJ
Adjust Pin Input Current
100
nA
%
∆VOL
Output Voltage Line
Regulation (Note 8)
Output Voltage Load
Regulation
VOUT +1V ≤ VIN ≤ 7.0V
0.02
0.06
0.06
0.12
∆VO/ ∆IOUT
10 mA ≤ IL ≤ 1.5A
%
(Note 8)
VIN - VOUT
IL = 150 mA
IL = 1.5A
38
380
5
50
60
450
550
9
Dropout Voltage
(Note 9)
mV
mA
IL = 150 mA
IL = 1.5A
10
14
15
10
50
Ground Pin Current In
Normal Operation Mode
IGND
6
IGND
Ground Pin Current In
Shutdown Mode
VSD ≤ 0.3V
0.01
1.8
3.2
µA
A
-40˚C ≤ TJ ≤ 85˚C
VO ≥ VO(NOM) - 4%
IO(PK)
Peak Output Current
Short Circuit Protection
ISC Short Circuit Current
A
5
www.national.com
Electrical Characteristics
LP3875-ADJ (Continued)
Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 10µF, VSD = 2V.
Symbol
Parameter
Conditions
Typ
LP3875-ADJ
Units
(Note 4)
(Note 5)
Min
Max
0.3
Shutdown Input
Output = High
VIN
0
2
VSDT
Shutdown Threshold
V
Output = Low
IL = 1.5A
TdOFF
TdON
Turn-off delay
Turn-on delay
SD Input Current
20
25
1
µs
µs
nA
IL = 1.5A
ISD
VSD = VIN
AC Parameters
VIN = VOUT + 1V
COUT = 10uF
73
57
VOUT = 3.3V, f = 120Hz
VIN = VOUT + 0.5V
COUT = 10uF
PSRR
Ripple Rejection
dB
VOUT = 3.3V, f = 120Hz
f = 120Hz
ρn(l/f)
Output Noise Density
Output Noise Voltage
0.8
µV
BW = 10Hz – 100kHz
VOUT = 2.5V
150
en
µV (rms)
BW = 300Hz – 300kHz
VOUT = 2.5V
100
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is
intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and test conditions, see Electrical Characteristics. The
guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed
test conditions.
Note 2: At elevated temperatures, devices must be derated based on package thermal resistance. The devices in TO220 package must be derated at θ = 50˚C/W
jA
2
(with 0.5in , 1oz. copper area), junction-to-ambient (with no heat sink). The devices in the TO263 surface-mount package must be derated at θ = 60˚C/W (with
0.5in , 1oz. copper area), junction-to-ambient. The SOT-223 package must be derated at θ = 90˚C/W (with 0.5in , 1oz. copper area), junction-to-ambient.
jA
2
2
jA
Note 3: The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.
Note 4: Typical numbers are at 25˚C and represent the most likely parametric norm.
Note 5: Limits are guaranteed by testing, design, or statistical correlation.
Note 6: If used in a dual-supply system where the regulator load is returned to a negative supply, the output must be diode-clamped to ground.
Note 7: The output PMOS structure contains a diode between the V and V
terminals. This diode is normally reverse biased. This diode will get forward biased
OUT
IN
if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can typically withstand 200mA of DC current and 1Amp
of peak current.
Note 8: Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage. Output voltage load
regulation is defined as the change in output voltage from the nominal value due to change in load current.
Note 9: Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value. Dropout voltage
specification applies only to output voltages of 2.5V and above. For output voltages below 2.5V, the drop-out voltage is nothing but the input to output differential,
since the minimum input voltage is 2.5V.
Note 10: The minimum operating value for V is equal to either [V
+ V
] or 2.5V, whichever is greater.
DROPOUT
IN
OUT(NOM)
www.national.com
6
Typical Performance Characteristics Unless otherwise specified: TJ = 25˚C, COUT = 10µF,
CIN = 10µF, S/D pin is tied to VIN, VOUT = 2.5V, VIN = VO(NOM) + 1V, IL = 10mA
Ground Current vs Output Voltage
Dropout Voltage vs Output Load Current
IL = 1.5A
20074660
20074654
Shutdown IQ vs Junction Temperature
DC Load Reg. vs Junction Temperature
20074655
20074658
DC Line Regulation vs Temperature
Noise vs Frequency
20074661
20074659
7
www.national.com
Typical Performance Characteristics Unless otherwise specified: TJ = 25˚C, COUT = 10µF,
CIN = 10µF, S/D pin is tied to VIN, VOUT = 2.5V, VIN = VO(NOM) + 1V, IL = 10mA (Continued)
Load Transient Response
CIN = COUT = 10µF, OSCON
Load Transient Response
CIN = COUT = 100µF, OSCON
20074677
20074676
Load Transient Response
Load Transient Response
CIN = COUT = 100µF, POSCAP
CIN = COUT = 10µF, TANTALUM
20074678
20074679
Load Transient Response
CIN = COUT = 100µF, TANTALUM
20074680
www.national.com
8
Application Hints
SETTING THE OUTPUT VOLTAGE
ESR Curve
The output voltage is set using the resistors R1 and R2 (see
Typical Application Circuit). The output is also dependent on
the reference voltage (typically 1.216V) which is measured
at the ADJ pin. The output voltage is given by the equation:
VOUT = VADJ x ( 1 + R1 / R2)
This equation does not include errors due to the bias current
flowing in the ADJ pin which is typically about 10 nA. This
>
error term is negligible for most applications. If R1 is
100kΩ , a small error may be introduced by the ADJ bias
current.
The tolerance of the external resistors used contributes a
significant error to the output voltage accuracy, with 1%
resistors typically adding a total error of approximately 1.4%
to the output voltage (this error is in addition to the tolerance
of the reference voltage at VADJ).
TURN-ON CHARACTERISTICS FOR OUTPUT
VOLTAGES PROGRAMMED TO 2.0V OR BELOW
20074670
As Vin increases during start-up, the regulator output will
track the input until Vin reaches the minimum operating
voltage (typically about 2.2V). For output voltages pro-
grammed to 2.0V or below, the regulator output may mo-
mentarily exceed its programmed output voltage during start
up. Outputs programmed to voltages above 2.0V are not
affected by this behavior.
CFF (Feed Forward Capacitor)
The capacitor CFF is required to add phase lead and help
improve loop compensation. The correct amount of capaci-
tance depends on the value selected for R1 (see Typical
Application Circuit). The capacitor should be selected such
that the zero frequency as given by the equation shown
below is approximately 45 kHz:
EXTERNAL CAPACITORS
Fz = 45,000 = 1 / ( 2 x π x R1 x CFF
)
Like any low-dropout regulator, external capacitors are re-
quired to assure stability. These capacitors must be correctly
selected for proper performance.
A good quality ceramic with X5R or X7R dielectric should be
used for this capacitor.
SELECTING A CAPACITOR
INPUT CAPACITOR: An input capacitor of at least 10µF is
required. Ceramic Ceramic, Tantalum, or Electrolytic capaci-
tors may be used, and capacitance may be increased with-
out limit
It is important to note that capacitance tolerance and varia-
tion with temperature must be taken into consideration when
selecting a capacitor so that the minimum required amount
of capacitance is provided over the full operating tempera-
ture range. In general, a good Tantalum capacitor will show
very little capacitance variation with temperature, but a ce-
ramic may not be as good (depending on dielectric type).
Aluminum electrolytics also typically have large temperature
variation of capacitance value.
OUTPUT CAPACITOR: An output capacitor is required for
loop stability. It must be located less than 1 cm from the
device and connected directly to the output and ground pins
using traces which have no other currents flowing through
them (see PCB Layout section).
The minimum value of output capacitance that can be used
for stable full-load operation is 10µF, but it may be increased
without limit. The output capacitor must have an ESR value
as shown in the stable region of the curve below. Tantalum
capacitors are recommended for the output capacitor.
Equally important to consider is a capacitor’s ESR change
with temperature: this is not an issue with ceramics, as their
ESR is extremely low. However, it is very important in Tan-
talum and aluminum electrolytic capacitors. Both show in-
creasing ESR at colder temperatures, but the increase in
aluminum electrolytic capacitors is so severe they may not
be feasible for some applications (see Capacitor Character-
istics Section).
CAPACITOR CHARACTERISTICS
CERAMIC: For values of capacitance in the 10 to 100 µF
range, ceramics are usually larger and more costly than
tantalums but give superior AC performance for bypassing
high frequency noise because of very low ESR (typically less
than 10 mΩ). However, some dielectric types do not have
good capacitance characteristics as a function of voltage
and temperature.
Z5U and Y5V dielectric ceramics have capacitance that
drops severely with applied voltage. A typical Z5U or Y5V
capacitor can lose 60% of its rated capacitance with half of
the rated voltage applied to it. The Z5U and Y5V also exhibit
9
www.national.com
these nodes resulting from current flowing through the
ground plane. Using a single point ground technique for the
regulator and it’s capacitors fixed the problem.
Application Hints (Continued)
a severe temperature effect, losing more than 50% of nomi-
nal capacitance at high and low limits of the temperature
range.
Since high current flows through the traces going into VIN
and coming from VOUT, Kelvin connect the capacitor leads to
these pins so there is no voltage drop in series with the input
and output capacitors.
X7R and X5R dielectric ceramic capacitors are strongly rec-
ommended if ceramics are used, as they typically maintain a
capacitance range within 20% of nominal over full operat-
ing ratings of temperature and voltage. Of course, they are
typically larger and more costly than Z5U/Y5U types for a
given voltage and capacitance.
RFI/EMI SUSCEPTIBILITY
RFI (radio frequency interference) and EMI (electromagnetic
interference) can degrade any integrated circuit’s perfor-
mance because of the small dimensions of the geometries
inside the device. In applications where circuit sources are
present which generate signals with significant high fre-
TANTALUM: Solid Tantalum capacitors are recommended
for use on the output because their typical ESR is very close
to the ideal value required for loop compensation. They also
work well as input capacitors if selected to meet the ESR
requirements previously listed.
>
quency energy content ( 1 MHz), care must be taken to
ensure that this does not affect the IC regulator.
If RFI/EMI noise is present on the input side of the regulator
(such as applications where the input source comes from the
output of a switching regulator), good ceramic bypass ca-
pacitors must be used at the input pin of the IC.
Tantalums also have good temperature stability: a good
quality Tantalum will typically show a capacitance value that
varies less than 10-15% across the full temperature range of
125˚C to −40˚C. ESR will vary only about 2X going from the
high to low temperature limits.
If a load is connected to the IC output which switches at high
speed (such as a clock), the high-frequency current pulses
required by the load must be supplied by the capacitors on
the IC output. Since the bandwidth of the regulator loop is
less than 100 kHz, the control circuitry cannot respond to
load changes above that frequency. The means the effective
output impedance of the IC at frequencies above 100 kHz is
determined only by the output capacitor(s).
The increasing ESR at lower temperatures can cause oscil-
lations when marginal quality capacitors are used (if the ESR
of the capacitor is near the upper limit of the stability range at
room temperature).
ALUMINUM: This capacitor type offers the most capaci-
tance for the money. The disadvantages are that they are
larger in physical size, not widely available in surface mount,
and have poor AC performance (especially at higher fre-
quencies) due to higher ESR and ESL.
In applications where the load is switching at high speed, the
output of the IC may need RF isolation from the load. It is
recommended that some inductance be placed between the
output capacitor and the load, and good RF bypass capaci-
tors be placed directly across the load.
Compared by size, the ESR of an aluminum electrolytic is
higher than either Tantalum or ceramic, and it also varies
greatly with temperature. A typical aluminum electrolytic can
exhibit an ESR increase of as much as 50X when going from
25˚C down to −40˚C.
PCB layout is also critical in high noise environments, since
RFI/EMI is easily radiated directly into PC traces. Noisy
circuitry should be isolated from "clean" circuits where pos-
sible, and grounded through a separate path. At MHz fre-
quencies, ground planes begin to look inductive and RFI/
EMI can cause ground bounce across the ground plane.
It should also be noted that many aluminum electrolytics only
specify impedance at a frequency of 120 Hz, which indicates
they have poor high frequency performance. Only aluminum
electrolytics that have an impedance specified at a higher
frequency (between 20 kHz and 100 kHz) should be used for
the LP387X. Derating must be applied to the manufacturer’s
ESR specification, since it is typically only valid at room
temperature.
In multi-layer PCB applications, care should be taken in
layout so that noisy power and ground planes do not radiate
directly into adjacent layers which carry analog power and
ground.
Any applications using aluminum electrolytics should be
thoroughly tested at the lowest ambient operating tempera-
ture where ESR is maximum.
OUTPUT NOISE
Noise is specified in two ways-
Spot Noise or Output noise density is the RMS sum of all
noise sources, measured at the regulator output, at a spe-
cific frequency (measured with a 1Hz bandwidth). This type
of noise is usually plotted on a curve as a function of fre-
quency.
PCB LAYOUT
Good PC layout practices must be used or instability can be
induced because of ground loops and voltage drops. The
input and output capacitors must be directly connected to the
input, output, and ground pins of the LP387X using traces
which do not have other currents flowing in them (Kelvin
connect).
Total output Noise or Broad-band noise is the RMS sum
of spot noise over a specified bandwidth, usually several
decades of frequencies.
The best way to do this is to lay out CIN and COUT near the
device with short traces to the VIN, VOUT, and ground pins.
The regulator ground pin should be connected to the exter-
nal circuit ground so that the regulator and its capacitors
have a "single point ground".
Attention should be paid to the units of measurement. Spot
√
√
noise is measured in units µV/ Hz or nV/ Hz and total output
noise is measured in µV(rms).
The primary source of noise in low-dropout regulators is the
internal reference. In CMOS regulators, noise has a low
frequency component and a high frequency component,
which depend strongly on the silicon area and quiescent
current. Noise can be reduced in two ways: by increasing the
transistor area or by increasing the current drawn by the
internal reference. Increasing the area will decrease the
chance of fitting the die into a smaller package. Increasing
It should be noted that stability problems have been seen in
applications where "vias" to an internal ground plane were
used at the ground points of the IC and the input and output
capacitors. This was caused by varying ground potentials at
www.national.com
10
The maximum allowable value for junction to ambient Ther-
mal Resistance, θJA, can be calculated using the formula:
Application Hints (Continued)
the current drawn by the internal reference increases the
total supply current (ground pin current). Using an optimized
trade-off of ground pin current and die size, LP3875-ADJ
achieves low noise performance and low quiescent current
operation.
θJA = TRmax / PD
The LP3875-ADJ is available in TO-220 and TO-263 pack-
ages. The thermal resistance depends on amount of copper
area or heat sink, and on air flow. If the maximum allowable
value of θJA calculated above is ≥ 60 ˚C/W for TO-220
package and ≥ 60 ˚C/W for TO-263 package no heatsink is
needed since the package can dissipate enough heat to
satisfy these requirements. If the value for allowable θJA falls
below these limits, a heat sink is required.
The total output noise specification for LP3875-ADJ is pre-
sented in the Electrical Characteristics table. The Output
noise density at different frequencies is represented by a
curve under typical performance characteristics.
SHORT-CIRCUIT PROTECTION
HEATSINKING TO-220 PACKAGE
The LP3875-ADJ is short circuit protected and in the event of
a peak over-current condition, the short-circuit control loop
will rapidly drive the output PMOS pass element off. Once
the power pass element shuts down, the control loop will
rapidly cycle the output on and off until the average power
dissipation causes the thermal shutdown circuit to respond
to servo the on/off cycling to a lower frequency. Please refer
to the section on thermal information for power dissipation
calculations.
The thermal resistance of a TO220 package can be reduced
by attaching it to a heat sink or a copper plane on a PC
board. If a copper plane is to be used, the values of θJA will
be same as shown in next section for TO263 package.
The heatsink to be used in the application should have a
heatsink to ambient thermal resistance,
θHA≤ θJA − θCH − θJC
.
In this equation, θCH is the thermal resistance from the case
to the surface of the heat sink and θJC is the thermal resis-
tance from the junction to the surface of the case. θJC is
about 3˚C/W for a TO220 package. The value for θCH de-
pends on method of attachment, insulator, etc. θCH varies
between 1.5˚C/W to 2.5˚C/W. If the exact value is unknown,
2˚C/W can be assumed.
SHUTDOWN OPERATION
A CMOS Logic level signal at the shutdown ( SD) pin will
turn-off the regulator. Pin SD must be actively terminated
through a 10kΩ pull-up resistor for a proper operation. If this
pin is driven from a source that actively pulls high and low
(such as a CMOS rail to rail comparator), the pull-up resistor
is not required. This pin must be tied to Vin if not used.
HEATSINKING TO-263 PACKAGE
The TO-263 package uses the copper plane on the PCB as
a heatsink. The tab of these packages are soldered to the
copper plane for heat sinking. Figure 1 shows a curve for the
DROPOUT VOLTAGE
The dropout voltage of a regulator is defined as the minimum
input-to-output differential required to stay within 2% of the
nominal output voltage. For CMOS LDOs, the dropout volt-
age is the product of the load current and the Rds(on) of the
internal MOSFET.
θ
JA of TO-263 package for different copper area sizes, using
a typical PCB with 1 ounce copper and no solder mask over
the copper area for heat sinking.
REVERSE CURRENT PATH
The internal MOSFET in the LP3875-ADJ has an inherent
parasitic diode. During normal operation, the input voltage is
higher than the output voltage and the parasitic diode is
reverse biased. However, if the output is pulled above the
input in an application, then current flows from the output to
the input as the parasitic diode gets forward biased. The
output can be pulled above the input as long as the current
in the parasitic diode is limited to 200mA continuous and 1A
peak.
POWER DISSIPATION/HEATSINKING
20074632
The LP3875-ADJ can deliver a continuous current of 1.5A
over the full operating temperature range. A heatsink may be
required depending on the maximum power dissipation and
maximum ambient temperature of the application. Under all
possible conditions, the junction temperature must be within
the range specified under operating conditions. The total
power dissipation of the device is given by:
FIGURE 1. θJA vs Copper (1 Ounce) Area for TO-263
package
As shown in the figure, increasing the copper area beyond 1
square inch produces very little improvement. The minimum
value for θJA for the TO-263 package mounted to a PCB is
32˚C/W.
PD = (VIN−VOUT)IOUT+ (VIN)IGND
where IGND is the operating ground current of the device
(specified under Electrical Characteristics).
Figure 2 shows the maximum allowable power dissipation
for TO-263 packages for different ambient temperatures,
assuming θJA is 35˚C/W and the maximum junction tempera-
ture is 125˚C.
The maximum allowable temperature rise (TRmax) depends
on the maximum ambient temperature (TAmax) of the appli-
cation, and the maximum allowable junction temperature
(TJmax):
TRmax = TJmax− TAmax
11
www.national.com
Application Hints (Continued)
The following figures show different layout scenarios for
SOT-223 package.
20074683
FIGURE 4. SCENARIO A, θJA = 148˚C/W
20074633
FIGURE 2. Maximum power dissipation vs ambient
temperature for TO-263 package
HEATSINKING SOT223-5 PACKAGE
Figure 3 shows a curve for the θJA of SOT-223 package for
different copper area sizes, using a typical PCB with 1 ounce
copper and no solder mask over the copper area for heat
sinking.
20074684
FIGURE 5. SCENARIO B, θJA = 125˚C/W
20074682
FIGURE 3. θJA vs Copper(1 Ounce) Area for SOT-223
package
www.national.com
12
Physical Dimensions inches (millimeters) unless otherwise noted
TO220 5-lead, Molded, Stagger Bend Package (TO220-5)
NS Package Number T05D
For Order Numbers, refer to the “Ordering Information” section of this document.
13
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
TO263 5-Lead, Molded, Surface Mount Package (TO263-5)
NS Package Number TS5B
For Order Numbers, refer to the “Ordering Information” section of this document.
www.national.com
14
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
SOT223, 5-Lead, Molded, Surface Mount Package (SOT223-5)
NS Package Number MP05A
For Order Numbers, refer to the “Ordering Information” section of this document.
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances
and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at:
www.national.com/quality/green.
Lead free products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
相关型号:
©2020 ICPDF网 联系我们和版权申明