935279067157_技术文档

SC16C554B/554DB

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte

FIFOs

Rev. 03 — 1 September 2005

Product data sheet

1. General description

The SC16C554B/554DB is a 4-channel Universal Asynchronous Receiver and

Transmitter (QUART) used for serial data communications. Its principal function is to

convert parallel data into serial data and vice versa. The UART can handle serial data

rates up to 5 Mbit/s. It comes with an Intel or Motorola interface.

The SC16C554B/554DB is pin compatible with the ST16C554 and TL16C554 and it will

power-up to be functionally equivalent to the 16C454. Programming of control registers

enables the added features of the SC16C554B/554DB. Some of these added features are

the 16-byte receive and transmit FIFOs, four receive trigger levels. The

SC16C554B/554DB also provides DMA mode data transfers through FIFO trigger levels

and the TXRDY and RXRDY signals. (TXRDY and RXRDY signals are not available in the

HVQFN48 package.) On-board status registers provide the user with error indications,

operational status, and modem interface control. System interrupts may be tailored to

meet user requirements. An internal loop-back capability allows on-board diagnostics.

The SC16C554B/554DB operates at 5 V, 3.3 V and 2.5 V, and the industrial temperature

range, and is available in plastic PLCC68, LQFP64, LQFP80, and HVQFN48 packages.

On the HVQFN48 package only, channel C has all the modem pins. Channels A and B

have only RTS and CTS pins and channel D does not have any modem pin.

2. Features

■ 4 channel UART

■ 5 V, 3.3 V and 2.5 V operation

■ Industrial temperature range (−40 °C to +85 °C)

■ The SC16C554B is pin and software compatible with the industry-standard

ST16C454/554, ST68C454/554, ST16C554, TL16C554

■ The SC16C554DB is pin and software compatible with ST16C554D, and software

compatible with ST16C454/554, ST16C554, TL16C554

■ Up to 5 Mbit/s data rate at 5 V and 3.3 V, and 3 Mbit/s at 2.5 V

■ 5 V tolerant inputs

■ 16-byte transmit FIFO

■ 16-byte receive FIFO with error ﬂags

■ Programmable auto-RTS and auto-CTS

◆ In auto-CTS mode, CTS controls transmitter

◆ In auto-RTS mode, RxFIFO contents and threshold control RTS

■ Automatic hardware ﬂow control (RTS/CTS)

■ Software selectable baud rate generator

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

■ Four selectable Receive FIFO interrupt trigger levels

■ Standard modem interface

■ Standard asynchronous error and framing bits (Start, Stop, and Parity Overrun Break)

■ Transmit, Receive, Line Status, and Data Set interrupts independently controlled

■ Fully programmable character formatting:

◆ 5-bit, 6-bit, 7-bit, or 8-bit characters

◆ Even, odd, or no-parity formats

◆ 1, 1¹⁄₂, or 2-stop bit

◆ Baud generation (DC to 5 Mbit/s)

■ False start-bit detection

■ Complete status reporting capabilities

■ 3-state output TTL drive capabilities for bidirectional data bus and control bus

■ Line break generation and detection

■ Internal diagnostic capabilities:

◆ Loop-back controls for communications link fault isolation

■ Prioritized interrupt system controls

■ Modem control functions (CTS, RTS, DSR, DTR, RI, CD).

3. Ordering information

Table 1:

Ordering information

Type number

Package

Name

Description

Version

SC16C554BIB64

SC16C554BIB80

SC16C554BIBM

SC16C554BIBS

LQFP64

LQFP80

LQFP64

plastic low proﬁle quad ﬂat package; 64 leads; body 10 × 10 × 1.4 mm

plastic low proﬁle quad ﬂat package; 80 leads; body 12 × 12 × 1.4 mm

plastic low proﬁle quad ﬂat package; 64 leads; body 7 × 7 × 1.4 mm

SOT314-2

SOT315-1

SOT414-1

SOT778-3

HVQFN48 plastic thermal enhanced very thin quad ﬂat package; no leads;

48 terminals; body 6 × 6 × 0.85 mm

SC16C554DBIA68 PLCC68

SC16C554DBIB64 LQFP64

plastic leaded chip carrier; 68 leads

SOT188-2

SOT314-2

plastic low proﬁle quad ﬂat package; 64 leads; body 10 × 10 × 1.4 mm

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

2 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

4. Block diagram

SC16C554B/554DB

TRANSMIT

FIFO

TRANSMIT

SHIFT

TXA to TXD

REGISTERS

REGISTER

D0 to D7

IOR

DATA BUS

AND

IOW

RESET

CONTROL

LOGIC

FLOW

CONTROL

LOGIC

RECEIVE

FIFO

RECEIVE

SHIFT

RXA to RXD

REGISTERS

REGISTER

FLOW

CONTROL

LOGIC

REGISTER

SELECT

LOGIC

A0 to A2

CSA to CSD

16/68

DTRA to DTRD

RTSA to RTSD

MODEM

CONTROL

LOGIC

INTA to INTD

TXRDY

CTSA to CTSD

RIA to RID

CDA to CDD

DSRA to DSRD

RXRDY

INTERRUPT

CONTROL

LOGIC

CLOCK AND

BAUD RATE

GENERATOR

INTSEL

002aaa877

XTAL1 XTAL2

CLKSEL

Fig 1. Block diagram of SC16C554B/554DB (16 mode)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

3 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

SC16C554B/554DB

TRANSMIT

FIFO

TRANSMIT

SHIFT

TXA to TXD

REGISTERS

REGISTER

DATA BUS

AND

D0 to D7

R/W

RESET

CONTROL

LOGIC

FLOW

CONTROL

LOGIC

RECEIVE

FIFO

RECEIVE

SHIFT

RXA to RXD

REGISTERS

REGISTER

FLOW

CONTROL

LOGIC

REGISTER

SELECT

LOGIC

A0 to A4

CS

16/68

DTRA to DTRD

RTSA to RTSD

MODEM

CONTROL

LOGIC

CTSA to CTSD

RIA to RID

CDA to CDD

DSRA to DSRD

IRQ

TXRDY

RXRDY

INTERRUPT

CONTROL

LOGIC

CLOCK AND

BAUD RATE

GENERATOR

002aaa878

XTAL1 XTAL2

CLKSEL

Fig 2. Block diagram of SC16C554B/554DB (68 mode)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

4 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

5. Pinning information

5.1 Pinning

5.1.1 PLCC68

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

60

59

58

57

56

55

54

53

52

51

50

49

48

47

46

45

44

DSRA

DSRD

CTSD

DTRD

GND

RTSD

INTD

CSD

CTSA

DTRA

V

CC

RTSA

INTA

CSA

TXA

TXD

IOW

SC16C554DBIA68

16 mode

IOR

TXB

TXC

CSB

CSC

INTB

RTSB

GND

DTRB

CTSB

DSRB

INTC

RTSC

V

CC

DTRC

CTSC

DSRC

002aaa879

Fig 3. Pin conﬁguration for PLCC68 (16 mode)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

5 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

60

59

58

57

56

55

54

53

52

51

50

49

48

47

46

45

44

DSRA

CTSA

DTRA

DSRD

CTSD

DTRD

GND

RTSD

n.c.

V

CC

RTSA

IRQ

CS

n.c.

TXA

R/W

TXB

A3

TXD

n.c.

SC16C554DBIA68

68 mode

TXC

A4

n.c.

RTSB

GND

DTRB

CTSB

DSRB

RTSC

V

CC

DTRC

CTSC

DSRC

002aaa880

Fig 4. Pin conﬁguration for PLCC68 (68 mode)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

6 of 56

SC16C554B/554DB

Philips Semiconductors

5.1.2 LQFP64

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

1

2

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

DSRA

CTSA

DTRA

DSRD

CTSD

DTRD

GND

RTSD

INTD

CSD

3

4

V

CC

5

RTSA

INTA

CSA

6

7

SC16C554BIB64

SC16C554DBIB64

SC16C554BIBM

8

TXA

TXD

9

IOW

IOR

10

11

12

13

14

15

16

TXB

TXC

CSB

CSC

INTB

RTSB

GND

DTRB

CTSB

INTC

RTSC

V

CC

DTRC

CTSC

002aaa881

Fig 5. Pin conﬁguration for LQFP64

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

7 of 56

SC16C554B/554DB

Philips Semiconductors

5.1.3 LQFP80

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

1

2

60

59

58

57

56

55

54

53

52

51

50

49

48

47

46

45

44

43

42

41

n.c.

CDD

RID

CDC

RIC

3

4

RXD

RXC

GND

TXRDY

RXRDY

RESET

n.c.

5

V

CC

6

INTSEL

D0

7

8

D1

9

D2

10

11

12

13

14

15

16

17

18

19

20

n.c.

D3

XTAL2

XTAL1

n.c.

SC16C554BIB80

D4

D5

A0

D6

A1

D7

A2

GND

RXA

RIA

CDA

n.c.

V

CC

RXB

RIB

CDB

n.c.

002aaa882

Fig 6. Pin conﬁguration for LQFP80

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

8 of 56

SC16C554B/554DB

Philips Semiconductors

5.1.4 HVQFN48

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

terminal 1

index area

1

2

36

35

34

33

32

31

30

29

28

27

26

25

CTSA

INTD

CSD

TXD

IOR

V

CC

3

RTSA

INTA

CSA

TXA

4

5

TXC

CSC

INTC

RTSC

6

SC16C554BIBS

16 mode

7

IOW

8

TXB

9

CSB

INTB

RTSB

CTSB

V

CC

10

11

12

DTRC

CTSC

DSRC

002aab552

Transparent top view

Fig 7. Pin conﬁguration for HVQFN (16 mode)

terminal 1

index area

1

2

36

35

34

33

32

31

30

29

28

27

26

25

CTSA

n.c.

V

CC

CSD

TXD

IOR

TXC

A4

3

RTSA

IRQ

4

5

CS

6

TXA

R/W

TXB

A3

SC16C554BIBS

68 mode

7

n.c.

8

RTSC

9

V

CC

10

11

12

n.c.

DTRC

CTSC

DSRC

RTSB

CTSB

002aab554

Transparent top view

Fig 8. Pin conﬁguration for HVQFN (68 mode)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

9 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

5.2 Pin description

Table 2:

Symbol

Pin description

PLCC68 LQFP64 LQFP80 HVQFN48

Type Description

16/68

31

-

14

I

16/68 Interface type select (input with internal

pull-up). This input provides the 16 (Intel) or 68

(Motorola) bus interface type select. The functions of

IOR, IOW, INTA to INTD, and CSA to CSD are

re-assigned with the logical state of this pin. When this

pin is a logic 1, the 16 mode interface (16C554) is

selected. When this pin is a logic 0, the 68 mode

interface (68C554) is selected. When this pin is a logic

0, IOW is re-assigned to R/W, RESET is re-assigned to

RESET, IOR is not used, and INTA to INTD are

connected in a wire-OR conﬁguration. The wire-OR

outputs are connected internally to the open drain IRQ

signal output. This pin is not available on 64-pin

packages which operate in the 16 mode only.

A0

A1

A2

34

33

32

24

23

22

48

47

46

17

16

15

I

Address 0 select bit. Internal registers address

selection in 16 and 68 modes.

Address 1 select bit. Internal registers address

selection in 16 and 68 modes.

Address 2 select bit. Internal registers address

selection in 16 and 68 modes.

A3

A4

20

50

-

9

Address 3 to Address 4 select bits. When the 68

mode is selected, these pins are used to address or

select individual UARTs (providing CS is a logic 0). In

the 16 mode, these pins are re-assigned as chip

selects, see CSB and CSC.

31

CDA

CDB

CDC

CDD

CS

9

64

18

31

49

-

19

42

59

2

-

I

Carrier Detect (active LOW). These inputs are

associated with individual UART channels A through D.

A logic 0 on this pin indicates that a carrier has been

detected by the modem for that channel.

27

43

61

16

-

24

-

5

Chip Select (active LOW). In the 68 mode, this pin

functions as a multiple channel chip enable. In this

case, all four UARTs (A to D) are enabled when the CS

pin is a logic 0. An individual UART channel is selected

by the data contents of address bits A3 to A4. when the

16 mode is selected (68-pin devices), this pin functions

as CSA (see deﬁnition under CSA, CSB).

CSA

CSB

CSC

CSD

16

20

50

54

7

28

33

68

73

5

I

Chip Select A, B, C, D (active LOW). This function is

associated with the 16 mode only, and for individual

channels ‘A’ through ‘D’. When in 16 mode, these pins

enable data transfers between the user CPU and the

SC16C554B/554DB for the channel(s) addressed.

Individual UART sections (A, B, C, D) are addressed by

providing a logic 0 on the respective CSA to CSD pin.

When the 68 mode is selected, the functions of these

pins are re-assigned. 68 mode functions are described

under their respective name/pin headings.

11

38

42

9

31

35

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

10 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Table 2:

Symbol

Pin description …continued

Type Description

PLCC68 LQFP64 LQFP80 HVQFN48

CTSA

CTSB

CTSC

CTSD

11

25

45

59

2

23

38

63

78

1

I

Clear to Send (active LOW). These inputs are

associated with individual UART channels A to D. A

logic 0 on the CTS pin indicates the modem or data set

is ready to accept transmit data from the

SC16C554B/554DB. Status can be tested by reading

MSR[4]. This pin only affects the transmit or receive

operations when auto-CTS function is enabled via

MCR[5] for hardware ﬂow control operation.

16

33

47

12

26

-

D0 to D2,

D3 to D7

66 to 68, 53 to 55, 7 to 9,

39 to 41, I/O

Data bus (bidirectional). These pins are the 8-bit,

3-state data bus for transferring information to or from

the controlling CPU. D0 is the least signiﬁcant bit and

the ﬁrst data bit in a transmit or receive serial data

stream.

1 to 5

56 to 60 11 to 15 42 to 46

DSRA

DSRB

DSRC

DSRD

10

26

44

60

1

22

39

62

79

-

I

Data Set Ready (active LOW). These inputs are

associated with individual UART channels, A through D.

A logic 0 on this pin indicates the modem or data set is

powered-on and is ready for data exchange with the

UART. This pin has no effect on the UART’s transmit or

receive operation.

17

32

48

-

25

-

DTRA

DTRB

DTRC

DTRD

12

24

46

58

3

24

37

64

77

-

O

Data Terminal Ready (active LOW). These outputs

are associated with individual UART channels, A

through D. A logic 0 on this pin indicates that the

SC16C554B/554DB is powered-on and ready. This pin

can be controlled via the Modem Control Register.

Writing a logic 1 to MCR[0] will set the DTR output to

logic 0, enabling the modem. This pin will be a logic 1

after writing a logic 0 to MCR[0], or after a reset. This

pin has no effect on the UART’s transmit or receive

operation.

15

34

46

-

27

-

GND

6, 23,

40, 57

14, 28,

45, 61

16, 36, 21, 37, 47

56, 76

I

Signal and power ground.

INTA

INTB

INTC

INTD

15

21

49

55

6

27

34

67

74

4

O

Interrupt A, B, C, D (active HIGH). This function is

associated with the 16 mode only. These pins provide

individual channel interrupts INTA to INTD.

12

37

43

10

30

36

INTA to INTD are enabled when MCR[3] is set to a

logic 1, interrupts are enabled in the Interrupt Enable

Register (IER), and when an interrupt condition exists.

Interrupt conditions include: receiver errors, available

receiver buffer data, transmit buffer empty, or when a

modem status ﬂag is detected. When the 68 mode is

selected, the functions of these pins are re-assigned.

68 mode functions are described under their respective

name/pin headings.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

11 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Table 2:

Symbol

Pin description …continued

Type Description

PLCC68 LQFP64 LQFP80 HVQFN48

INTSEL

65

-

6

-

I

Interrupt Select (active HIGH, with internal

pull-down). This function is associated with the

16 mode only. When the 16 mode is selected, this pin

can be used in conjunction with MCR[3] to enable or

disable the 3-state interrupts, INTA to INTD, or override

MCR[3] and force continuous interrupts. Interrupt

outputs are enabled continuously by making this pin a

logic 1. Making this pin a logic 0 allows MCR[3] to

control the 3-state interrupt output. In this mode,

MCR[3] is set to a logic 1 to enable the 3-state outputs.

This pin is disabled in the 68 mode. Due to pin

limitations on the 64-pin packages, this pin is not

available. To cover this limitation, the

SC16C554DBIB64 version operates in the continuous

interrupt enable mode by bonding this pin to V_CC

internally. The SC16C554BIB64 operates with MCR[3]

control by bonding this pin to GND. The INTSEL pin is

not available on the HVQFN48 package.

IOR

52

18

40

70

31

33

I

Input/Output Read strobe (active LOW). This function

is associated with the 16 mode only. A logic 0 transition

on this pin will load the contents of an internal register

deﬁned by address bits A0 to A2 onto the

SC16C554B/554DB data bus (D0 to D7) for access by

external CPU. This pin is disabled in the 68 mode.

IOW

9

7

Input/Output Write strobe (active LOW). This

function is associated with the 16 mode only. A logic 0

transition on this pin will transfer the contents of the

data bus (D0 to D7) from the external CPU to an

internal register that is deﬁned by address bits

A0 to A2. When the 68 mode is selected, this pin

functions as R/W (see deﬁnition under R/W).

IRQ

15

-

4

O

Interrupt Request or Interrupt ‘A’. This function is

associated with the 68 mode only. In the 68 mode,

interrupts from UART channels A to D are wire-ORed

internally to function as a single IRQ interrupt. This pin

transitions to a logic 0 (if enabled by the Interrupt

Enable Register) whenever a UART channel(s) requires

service. Individual channel interrupt status can be

determined by addressing each channel through its

associated internal register, using CS and A3 to A4. In

the 68 mode, and external pull-up resistor must be

connected between this pin and V_CC. The function of

this pin changes to INTA when operating in the

16 mode (see deﬁnition under INTA).

n.c.

21, 49,

52, 54,

55, 65

-

1, 10,

20, 21,

30, 40,

41, 49,

52, 60,

61, 71,

80

-

not connected

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

12 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Table 2:

Symbol

Pin description …continued

Type Description

PLCC68 LQFP64 LQFP80 HVQFN48

RESET

(RESET)

37

27

53

20

I

Reset. In the 16 mode, a logic 1 on this pin will reset

the internal registers and all the outputs. The UART

transmitter output and the receiver input will be disabled

during reset time. (See Section 7.10

“SC16C554B/554DB external reset conditions” for

initialization details.) When 16/68 is a logic 0 (68

mode), this pin functions similarly, bus as an inverted

reset interface signal, RESET.

RIA

8

63

19

30

50

5

18

43

58

3

-

I

Ring Indicator (active LOW). These inputs are

associated with individual UART channels, A to D. A

logic 0 on this pin indicates the modem has received a

ringing signal from the telephone line. A logic 1

transition on this input pin will generate an interrupt.

RIB

28

42

62

14

22

48

56

-

RIC

23

-

RID

RTSA

RTSB

RTSC

RTSD

26

35

66

75

3

O

Request to Send (active LOW). These outputs are

associated with individual UART channels, A to D. A

logic 0 on the RTS pin indicates the transmitter has

data ready and waiting to send. Writing a logic 1 in the

Modem Control Register MCR[1] will set this pin to a

logic 0, indicating data is available. After a reset this pin

will be set to a logic 1. This pin only affects the transmit

and receive operations when auto-RTS function is

enabled via MCR[5] for hardware ﬂow control operation.

13

36

44

11

29

-

R/W

18

-

7

I

Read/Write strobe. This function is associated with the

68 mode only. This pin provides the combined functions

for Read or Write strobes.

Logic 1 = Read from UART register selected by CS and

A0 to A4.

Logic 0 = Write to UART register selected by CS and

A0 to A4.

RXA

RXB

RXC

RXD

7

62

20

29

51

17

44

57

4

48

13

22

38

I

Receive data input RXA to RXD. These inputs are

associated with individual serial channel data to the

SC16C554B/554DB. The RX signal will be a logic 1

during reset, idle (no data), or when the transmitter is

disabled. During the local loop-back mode, the RX input

pin is disabled and TX data is connected to the UART

RX input internally.

29

41

63

RXRDY

38

-

54

-

O

Receive Ready (active LOW). RXRDY contains the

wire-ORed status of all four receive channel FIFOs,

RXRDYA to RXRDYD. A logic 0 indicates receive data

ready status, that is, the RHR is full, or the FIFO has

one or more RX characters available for unloading. This

pin goes to a logic 1 when the FIFO/RHR is empty, or

when there are no more characters available in either

the FIFO or RHR. Individual channel RX status is read

by examining individual internal registers via CS and

A0 to A4 pin functions. The RXRDY pin is not available

on the HVQFN48 package.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

13 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Table 2:

Symbol

Pin description …continued

Type Description

PLCC68 LQFP64 LQFP80 HVQFN48

TXA

TXB

TXC

TXD

17

19

51

53

8

29

32

69

72

6

O

Transmit data A, B, C, D. These outputs are

associated with individual serial transmit channel data

from the SC16C554B/554DB. The TX signal will be a

logic 1 during reset, idle (no data), or when the

transmitter is disabled. During the local loop-back

mode, the TX output pin is disabled and TX data is

internally connected to the UART RX input.

10

39

41

8

32

34

TXRDY

39

-

55

-

Transmit Ready (active LOW). TXRDY contains the

wire-ORed status of all four transmit channel FIFOs,

TXRDYA to TXRDYD. A logic 0 indicates a buffer ready

status, that is, at least one location is empty and

available in one of the TX channels (A to D). This pin

goes to a logic 1 when all four channels have no more

empty locations in the TX FIFO or THR. Individual

channel TX status can be read by examining individual

internal registers via CS and A0 to A4 pin functions.

The TXRDY pin is not available on the HVQFN48

package.

V_CC

13, 30,

47, 64

4, 21,

35, 52

5, 25,

45, 65

2, 28

18

I

Power supply inputs.

XTAL1

35

25

50

Crystal or external clock input. Functions as a crystal

input or as an external clock input. A crystal can be

connected between this pin and XTAL2 to form an

internal oscillator circuit (see Figure 13). Alternatively,

an external clock can be connected to this pin to

provide custom data rates. (See Section 6.6

“Programmable baud rate generator”.)

XTAL2

36

26

51

19

O

Output of the crystal oscillator or buffered clock.

(See also XTAL1.) Crystal oscillator output or buffered

clock output.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

14 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

6. Functional description

The SC16C554B/554DB provides serial asynchronous receive data synchronization,

parallel-to-serial and serial-to-parallel data conversions for both the transmitter and

receiver sections. These functions are necessary for converting the serial data stream into

parallel data that is required with digital data systems. Synchronization for the serial data

stream is accomplished by adding start and stop bits to the transmit data to form a data

character. Data integrity is insured by attaching a parity bit to the data character. The

parity bit is checked by the receiver for any transmission bit errors. The electronic circuitry

to provide all these functions is fairly complex, especially when manufactured on a single

integrated silicon chip. The SC16C554B/554DB represents such an integration with

greatly enhanced features. The SC16C554B/554DB is fabricated with an advanced

CMOS process to achieve low drain power and high speed requirements.

The SC16C554B/554DB is an upward solution that provides 16 bytes of transmit and

receive FIFO memory, instead of none in the 16C454. The SC16C554B/554DB is

designed to work with high speed modems and shared network environments that require

fast data processing time. Increased performance is realized in the SC16C554B/554DB

by the larger transmit and receive FIFOs. This allows the external processor to handle

more networking tasks within a given time. In addition, the four selectable levels of FIFO

trigger interrupt is uniquely provided for maximum data throughput performance,

especially when operating in a multi-channel environment. The combination of the above

greatly reduces the bandwidth requirement of the external controlling CPU, increases

performance, and reduces power consumption.

The SC16C554B/554DBAI68 combines the package interface modes of the 16C454/554

and 68C454/554 series on a single integrated chip. The 16 mode interface is designed to

operate with the Intel-type of microprocessor bus, while the 68 mode is intended to

operate with Motorola and other popular microprocessors. Following a reset, the

SC16C554B/554DBAI68 is downward compatible with the 16C454/554 or the

68C454/554, dependent on the state of the interface mode selection pin, 16/68.

The SC16C554B/554DB is capable of operation to 1.5 Mbit/s with a 24 MHz crystal and

up to 5 Mbit/s with an external clock input (at 3.3 V and 5 V; at 2.5 V the maximum speed

is 3 Mbit/s).

The rich feature set of the SC16C554B/554DB is available through internal registers.

Selectable receive FIFO trigger levels, selectable TX and RX baud rates, and modem

interface controls are all standard features. In the 16 mode, INTSEL and MCR[3] can be

conﬁgured to provide a software controlled or continuous interrupt capability. Due to pin

limitations of the 64-pin package, this feature is offered by two different LQFP64

packages. The SC16C554DB operates in the continuous interrupt enable mode by

bonding INTSEL to V_CCinternally. The SC16C554B operates in conjunction with MCR[3]

by bonding INTSEL to GND internally.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

15 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

6.1 Interface options

Two user interface modes are selectable for the PLCC68 package. These interface modes

are designated as the ‘16 mode’ and the ‘68 mode’. This nomenclature corresponds to the

early 16C454/554 and 68C454/554 package interfaces respectively.

6.1.1 The 16 mode interface

The 16 mode conﬁgures the package interface pins for connection as a standard

16 series (Intel) device and operates similar to the standard CPU interface available on

the 16C454/554. In the 16 mode (pin 16/68 = logic 1), each UART is selected with

individual chip select (CSx) pins, as shown in Table 3.

Table 3:

Serial port channel selection, 16 mode interface

CSA

CSB

CSC

CSD

UART channel

1

0

1

0

1

0

1

0

none

A

B

C

D

6.1.2 The 68 mode interface

The 68 mode conﬁgures the package interface pins for connection with Motorola, and

other popular microprocessor bus types. The interface operates similar to the

68C454/554. In this mode, the SC16C554B/554DB decodes two additional addresses,

A3 to A4, to select one of the four UART ports. The A3 to A4 address decode function is

used only when in the 68 mode (16/68 = logic 0), and is shown in Table 4.

Table 4:

Serial port channel selection, 68 mode interface

CS

1

A4

n/a

0

A3

n/a

0

UART channel

none

A

0

1

B

0

1

0

C

0

1

D

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

16 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

6.2 Internal registers

The SC16C554B/554DB provides 12 internal registers for monitoring and control. These

registers are shown in Table 5. These registers function as data holding registers

(THR/RHR), interrupt status and control registers (IER/ISR), a FIFO Control Register

(FCR), line status and control registers (LCR/LSR), modem status and control registers

(MCR/MSR), programmable data rate (clock) control registers (DLL/DLM), and a user

accessible Scratchpad Register (SPR). Register functions are more fully described in the

following paragraphs.

Table 5:

A2

Internal registers decoding

A0 Read mode

A1

Write mode

General register set (THR/RHR, IER/ISR, MCR/MSR, FCR, LSR, SPR)^[1]

0

1

0

1

0

1

0

1

0

1

0

1

0

1

Receive Holding Register

Interrupt Enable Register

Interrupt Status Register

Line Control Register

Modem Control Register

Line Status Register

Transmit Holding Register

Interrupt Enable Register

FIFO Control Register

Line Control Register

Modem Control Register

n/a

Modem Status Register

n/a

Scratchpad Register

Baud rate register set (DLL/DLM)^[2]

0

1

LSB of Divisor Latch

MSB of Divisor Latch

LSB of Divisor Latch

MSB of Divisor Latch

[1] These registers are accessible only when LCR[7] is a logic 0.

[2] These registers are accessible only when LCR[7] is a logic 1.

6.3 FIFO operation

The 16 byte transmit and receive data FIFOs are enabled by the FIFO Control Register

(FCR) bit 0. With SC16C554B devices, the user can set the receive trigger level, but not

the transmit trigger level. The receiver FIFO section includes a time-out function to ensure

data is delivered to the external CPU. An interrupt is generated whenever the Receive

Holding Register (RHR) has not been read following the loading of a character or the

receive trigger level has not been reached.

Table 6:

Flow control mechanism

Selected trigger level

(characters)

INT pin activation

Negate RTS

Assert RTS

1

4

1

4

8

4

8

12

14

8

14

10

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

17 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

6.4 Autoﬂow control (see Figure 9)

Autoﬂow control is comprised of auto-CTS and auto-RTS. With auto-CTS, the CTS input

must be active before the transmitter FIFO can emit data. With auto-RTS, RTS becomes

active when the receiver needs more data and notiﬁes the sending serial device. When

RTS is connected to CTS, data transmission does not occur unless the receiver FIFO has

space for the data; thus, overrun errors are eliminated using UART 1 and UART 2 from a

SC16C554B/554DB with the autoﬂow control enabled. If not, overrun errors occur when

the transmit data rate exceeds the receiver FIFO read latency.

ACE1

ACE2

SERIAL TO

PARALLEL

RX

TX

TO SERIAL

RCV

FIFO

XMT

FIFO

RTS

CTS

FLOW

CONTROL

D7 to D0

PARALLEL

TO SERIAL

SERIAL TO

PARALLEL

TX

RX

XMT

FIFO

RCV

FIFO

CTS

RTS

FLOW

CONTROL

002aaa048

Fig 9. Autoﬂow control (auto-RTS and auto-CTS) example

6.4.1 Auto-RTS (see Figure 9)

Auto-RTS data ﬂow control originates in the receiver timing and control block (see block

diagrams in Figure 1 and Figure 2) and is linked to the programmed receiver FIFO trigger

level. When the receiver FIFO level reaches a trigger level of 1, 4, or 8 (see Figure 11),

RTS is de-asserted. With trigger levels of 1, 4, and 8, the sending UART may send an

additional byte after the trigger level is reached (assuming the sending UART has another

byte to send) because it may not recognize the de-assertion of RTS until after it has

begun sending the additional byte. RTS is automatically reasserted once the RX FIFO is

emptied by reading the receiver buffer register. When the trigger level is 14 (see

Figure 12), RTS is de-asserted after the ﬁrst data bit of the 16th character is present on

the RX line. RTS is reasserted when the RX FIFO has at least one available byte space.

Remark: Auto-RTS is not supported in channel D of the HVQFN48 package, therefore

MCR[5] of channel D should not be written.

6.4.2 Auto-CTS (see Figure 9)

The transmitter circuitry checks CTS before sending the next data byte. When CTS is

active, it sends the next byte. To stop the transmitter from sending the following byte, CTS

must be released before the middle of the last stop bit that is currently being sent (see

Figure 10). The auto-CTS function reduces interrupts to the host system. When ﬂow

control is enabled, CTS level changes do not trigger host interrupts because the device

automatically controls its own transmitter. Without auto-CTS, the transmitter sends any

data present in the transmit FIFO and a receiver overrun error may result.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

18 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Remark: Auto-CTS is not supported in channel D of the HVQFN48 package, therefore

MCR[5] of channel D should not be written.

6.4.3 Enabling autoﬂow control and auto-CTS

Autoﬂow control is enabled by setting MCR[5] and MCR[1].

Table 7:

Enabling autoﬂow control and auto-CTS

MCR[5]

MCR[1]

Selection

1

0

1

0

X

auto RTS and CTS

auto CTS

disable

6.4.4 Auto-CTS and auto-RTS functional timing

Start

bits 0 to 7 Stop

Start

bits 0 to 7 Stop

Start

bits 0 to 7 Stop

TX

CTS

002aaa049

(1) When CTS is LOW, the transmitter keeps sending serial data out.

(2) If CTS goes HIGH before the middle of the last stop bit of the current byte, the transmitter ﬁnishes sending the current byte,

but is does not send the next byte.

(3) When CTS goes from HIGH to LOW, the transmitter begins sending data again.

Fig 10. CTS functional timing waveforms

The receiver FIFO trigger level can be set to 1 byte, 4 bytes, 8 bytes, or 14 bytes. These

are described in Figure 11 and Figure 12.

RX

Start

byte N

Stop

Start

byte N + 1 Stop

Start

byte

Stop

RTS

1

2

N

N + 1

IOR

(RD RBR)

002aaa050

(1) N = RCV FIFO trigger level (1 byte, 4 bytes, or 8 bytes).

(2) The two blocks in dashed lines cover the case where an additional byte is sent as described in Section 6.4.1

Fig 11. RTS functional timing waveforms, RCV FIFO trigger level = 1 byte, 4 bytes, or 8 bytes

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

19 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

RX

byte 14

byte 15

Start

byte 16

Stop

Start

byte 18

Stop

RTS released after the

first data bit of byte 16

RTS

IOR

(RD RBR)

002aaa051

(1) RTS is de-asserted when the receiver receives the ﬁrst data bit of the sixteenth byte. The receive FIFO is full after ﬁnishing

the sixteenth byte.

(2) RTS is asserted again when there is at least one byte of space available and no incoming byte is in processing, or there is

more than one byte of space available.

(3) When the receive FIFO is full, the ﬁrst receive buffer register read re-asserts RTS.

Fig 12. RTS functional timing waveforms, RCV FIFO trigger level = 14 bytes

6.5 Hardware/software and time-out interrupts

Following a reset, if the transmitter interrupt is enabled, the SC16C554B/554DB will issue

an interrupt to indicate that the Transmit Holding Register is empty. This interrupt must be

serviced prior to continuing operations. The LSR register provides the current singular

highest priority interrupt only. Only after servicing the higher pending interrupt will the

lower priority interrupt(s) be reﬂected in the status register. Servicing the interrupt without

investigating further interrupt conditions can result in data errors.

When two interrupt conditions have the same priority, it is important to service these

interrupts correctly. Receive Data Ready and Receive Time Out have the same interrupt

priority (when enabled by IER[0]). The receiver issues an interrupt after the number of

characters have reached the programmed trigger level. In this case, the

SC16C554B/554DB FIFO may hold more characters than the programmed trigger level.

Following the removal of a data byte, the user should re-check LSR[0] for additional

characters. A Receive Time Out will not occur if the receive FIFO is empty. The time-out

counter is reset at the center of each stop bit received or each time the Receive Holding

Register (RHR) is read. The actual time-out value is 4 character time.

In the 16 mode for the PLCC68 package, the system/board designer can optionally

provide software controlled 3-state interrupt operation. This is accomplished by INTSEL

and MCR[3]. When INTSEL interface pin is left open or made a logic 0, MCR[3] controls

the 3-state interrupt outputs, INTA to INTD. When INTSEL is a logic 1, MCR[3] has no

effect on the INTA to INTD outputs, and the package operates with interrupt outputs

enabled continuously.

6.6 Programmable baud rate generator

The SC16C554B/554DB supports high speed modem technologies that have increased

input data rates by employing data compression schemes. For example, a 33.6 kbit/s

modem that employs data compression may require a 115.2 kbit/s input data rate.

A 128.0 kbit/s ISDN modem that supports data compression may need an input data rate

of 460.8 kbit/s.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

20 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

A single baud rate generator is provided for the transmitter and receiver, allowing

independent TX/RX channel control. The programmable Baud Rate Generator is capable

of accepting an input clock up to 80 MHz (for 3.3 V and 5 V operation), as required for

supporting a 5 Mbit/s data rate. The SC16C554B/554DB can be conﬁgured for internal or

external clock operation. For internal clock oscillator operation, an industry standard

microprocessor crystal (parallel resonant/22 pF to 33 pF load) is connected externally

between the XTAL1 and XTAL2 pins (see Figure 13). Alternatively, an external clock can

be connected to the XTAL1 pin to clock the internal baud rate generator for standard or

custom rates (see Table 8).

XTAL1

XTAL2

XTAL1

XTAL2

1.5 kΩ

X1

1.8432 MHz

C1

22 pF

C2

33 pF

C1

22 pF

C2

47 pF

002aaa870

Fig 13. Crystal oscillator connection

Programming the Baud Rate Generator registers DLM (MSB) and DLL (LSB) provides a

user capability for selecting the desired ﬁnal baud rate.

Table 8:

Baud rate generator programming table using a 7.3728 MHz clock

Output baud rate

(bit/s)

User

16× clock divisor

DLM

DLL

program value program value

(HEX)

Decimal

HEX

900

180

C0

60

200

2304

384

192

96

48

24

12

6

09

01

00

80

C0

60

30

18

0C

06

03

02

01

1200

2400

4800

9600

30

19.2 k

38.4 k

76.8 k

153.6 k

230.4 k

460.8 k

18

0C

06

3

03

2

02

1

01

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

21 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

6.7 DMA operation

The SC16C554B/554DB FIFO trigger level provides additional ﬂexibility to the user for

block mode operation. LSR[5:6] provide an indication when the transmitter is empty or has

an empty location(s). The user can optionally operate the transmit and receive FIFOs in

the DMA mode (FCR[3]). When the transmit and receive FIFOs are enabled and the DMA

mode is de-activated (DMA Mode 0), the SC16C554B/554DB activates the interrupt

output pin for each data transmit or receive operation. When DMA mode is activated

(DMA Mode 1), the user takes the advantage of block mode operation by loading or

unloading the FIFO in a block sequence determined by the preset trigger level. In this

mode, the SC16C554B/554DB sets the interrupt output pin when the characters in the

receive FIFOs are above the receive trigger level.

Remark: DMA operation is not supported in the HVQFN48 package.

6.8 Loop-back mode

The internal loop-back capability allows on-board diagnostics. In the loop-back mode, the

normal modem interface pins are disconnected and reconﬁgured for loop-back internally.

MCR[0:3] register bits are used for controlling loop-back diagnostic testing. In the

loop-back mode, OP1 and OP2 in the MCR register (bits 2:3) control the modem RI and

CD inputs, respectively. MCR signals DTR and RTS (bits 0:1) are used to control the

modem DSR and CTS inputs, respectively. The transmitter output (TX) and the receiver

input (RX) are disconnected from their associated interface pins, and instead are

connected together internally (see Figure 14). The CTS, DSR, CD, and RI are

disconnected from their normal modem control input pins, and instead are connected

internally to RTS, DTR, OP2 and OP1. Loop-back test data is entered into the Transmit

Holding Register via the user data bus interface, D0 to D7. The transmit UART serializes

the data and passes the serial data to the receive UART via the internal loop-back

connection. The receive UART converts the serial data back into parallel data that is then

made available at the user data interface D0 to D7. The user optionally compares the

received data to the initial transmitted data for verifying error-free operation of the UART

TX/RX circuits.

In this mode, the receiver and transmitter interrupts are fully operational. The Modem

Control Interrupts are also operational. However, the interrupts can only be read using

lower four bits of the Modem Status Register (MSR[0:3]) instead of the four Modem Status

Register bits 4:7. The interrupts are still controlled by the IER.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

22 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

SC16C554B/554DB

TRANSMIT

FIFO

TRANSMIT

SHIFT

TXA to TXD

REGISTERS

REGISTER

D0 to D7

IOR

DATA BUS

AND

IOW

RESET

CONTROL

LOGIC

FLOW

CONTROL

LOGIC

RECEIVE

FIFO

REGISTERS

RECEIVE

SHIFT

REGISTER

RXA to RXD

FLOW

CONTROL

LOGIC

REGISTER

SELECT

LOGIC

A0 to A2

CSA to CSD

RTSA to RTSD

CTSA to CTSD

DTRA to DTRD

MODEM

CONTROL

LOGIC

DSRA to DSRD

OP1A to OP1D

INTA to INTD

TXRDY

INTERRUPT

CONTROL

LOGIC

CLOCK AND

BAUD RATE

GENERATOR

RIA to RID

RXRDY

OP2A to OP2D

CDA to CDD

002aaa883

XTAL1 XTAL2

Fig 14. Internal loop-back mode diagram (16 mode)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

23 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

SC16C554B/554DB (HVQFN48)

TRANSMIT

FIFO

TRANSMIT

SHIFT

TXA to TXD

REGISTERS

REGISTER

D0 to D7

IOR

DATA BUS

AND

IOW

RESET

CONTROL

LOGIC

FLOW

CONTROL

LOGIC

RECEIVE

FIFO

REGISTERS

RECEIVE

SHIFT

REGISTER

RXA to RXD

FLOW

CONTROL

LOGIC

REGISTER

SELECT

LOGIC

A0 to A2

CSA to CSD

RTSA to RTSC

CTSA to CTSC

DTRC

MODEM

CONTROL

LOGIC

DSRC

OP1C

INTERRUPT

CONTROL

LOGIC

CLOCK AND

BAUD RATE

GENERATOR

INTA to INTD

RIC

OP2C

CDC

002aab553

XTAL1 XTAL2

Fig 15. Internal loop-back mode diagram (16 mode) for HVQFN48 package

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

24 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

SC16C554B/554DB

TRANSMIT

FIFO

TRANSMIT

SHIFT

TXA to TXD

REGISTERS

REGISTER

D0 to D7

R/W

DATA BUS

AND

RESET

CONTROL

LOGIC

FLOW

CONTROL

LOGIC

RECEIVE

FIFO

REGISTERS

RECEIVE

SHIFT

REGISTER

RXA to RXD

FLOW

CONTROL

LOGIC

REGISTER

SELECT

LOGIC

A0 to A4

CS

RTSA to RTSD

CTSA to CTSD

DTRA to DTRD

16/68

DSRA to DSRD

OP1A to OP1D

MODEM

CONTROL

LOGIC

IRQ

TXRDY

RXRDY

INTERRUPT

CONTROL

LOGIC

CLOCK AND

BAUD RATE

GENERATOR

RIA to RID

OP2A to OP2D

CDA to CDD

002aaa884

XTAL1 XTAL2

Fig 16. Internal loop-back mode diagram (68 mode)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

25 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

SC16C554B/554DB (HVQFN48)

TRANSMIT

FIFO

TRANSMIT

SHIFT

TXA to TXD

REGISTERS

REGISTER

D0 to D7

R/W

DATA BUS

AND

RESET

CONTROL

LOGIC

FLOW

CONTROL

LOGIC

RECEIVE

FIFO

REGISTERS

RECEIVE

SHIFT

REGISTER

RXA to RXD

FLOW

CONTROL

LOGIC

REGISTER

SELECT

LOGIC

A0 to A4

CS

RTSC

CTSC

DTRC

16/68

DSRC

OP1C

MODEM

CONTROL

LOGIC

INTERRUPT

CONTROL

LOGIC

CLOCK AND

BAUD RATE

GENERATOR

IRQ

RIC

OP2C

CDC

002aab555

XTAL1 XTAL2

Fig 17. Internal loop-back mode diagram (68 mode) for HVQFN48 package

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

26 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

7. Register descriptions

Table 9 details the assigned bit functions for the SC16C554B/554DB internal registers.

The assigned bit functions are more fully deﬁned in Section 7.1 through Section 7.10.

Table 9:

SC16C554B/554DB internal registers

A2 A1 A0 Register Default^[1]Bit 7

General Register set^[2]

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

0

1

RHR

THR

IER

XX

00

bit 7

0

bit 6

0

bit 5

0

bit 4

0

bit 3

bit 2

bit 1

bit 0

modem receive

status line status holding holding

interrupt interrupt register register

transmit receive

0

1

0

1

0

1

FCR

ISR

00

01

00

60

RCVR

trigger

(MSB)

RCVR

trigger

(LSB)

reserved reserved DMA

mode

XMIT

FIFO reset FIFO

reset

RCVR

FIFO

enable

select^[3]

FIFOs

enabled enabled

FIFOs

0

INT

priority

bit 1

INT

priority

bit 0

INT

status

priority

bit 2

LCR

MCR

LSR

divisor

latch

enable

set

break

set

even

parity

stop bits

OP1

word

length

bit 1

word

length

bit 0

parity

enable

0

autoﬂow loop back OP2,

RTS

DTR

control

enable^[4]

INTx

enable

FIFO

data

error

trans.

empty

trans.

break

framing parity

overrun receive

error

holding interrupt error

empty

error

data

ready

1

0

1

MSR

SPR

X0

FF

CD

RI

DSR

bit 5

CTS

bit 4

∆CD

∆RI

∆DSR

∆CTS

bit 7

bit 6

bit 3

bit 2

bit 1

bit 0

Special Register set^[5]

0

1

DLL

XX

bit 7

bit 6

bit 5

bit 4

bit 3

bit 2

bit 1

bit 9

bit 0

bit 8

DLM

bit 15

bit 14

bit 13

bit 12

bit 11

bit 10

[1] The value shown represents the register’s initialized HEX value; X = not applicable.

[2] These registers are accessible only when LCR[7] = 0.

[3] This function is not supported in the HVQFN48 package.

[4] Autoﬂow control is not supported by channel D of the HVQFN48 package, and this bit should not be written on channel D.

[5] The Special Register set is accessible only when LCR[7] is set to a logic 1.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

27 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

7.1 Transmit (THR) and Receive (RHR) Holding Registers

The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and

Transmit Shift Register (TSR). The status of the THR is provided in the Line Status

Register (LSR). Writing to the THR transfers the contents of the data bus (D7 to D0) to the

THR, providing that the THR or TSR is empty. The THR empty ﬂag in the LSR register will

be set to a logic 1 when the transmitter is empty or when data is transferred to the TSR.

Note that a write operation can be performed when the THR empty ﬂag is set

(logic 0 = FIFO full; logic 1 = at least one FIFO location available).

The serial receive section also contains an 8-bit Receive Holding Register (RHR).

Receive data is removed from the SC16C554B/554DB and receive FIFO by reading the

RHR register. The receive section provides a mechanism to prevent false starts. On the

falling edge of a start or false start bit, an internal receiver counter starts counting clocks

at the 16× clock rate. After 7¹⁄₂clocks, the start bit time should be shifted to the center of

the start bit. At this time the start bit is sampled, and if it is still a logic 0 it is validated.

Evaluating the start bit in this manner prevents the receiver from assembling a false

character. Receiver status codes will be posted in the LSR.

7.2 Interrupt Enable Register (IER)

The Interrupt Enable Register (IER) masks the interrupts from receiver ready, transmitter

empty, line status and modem status registers. These interrupts would normally be seen

on the INTA to INTD output pins in the 16 mode, or on wire-OR IRQ output pin in the

68 mode.

Table 10: Interrupt Enable Register bits description

Bit

7:4

3

Symbol

IER[7:4]

IER[3]

Description

Reserved; set to ‘0’.

Modem status interrupt.

logic 0 = disable the modem status register interrupt (normal default

condition)

logic 1 = enable the modem status register interrupt

Receive line status interrupt.

2

1

IER[2]

IER[1]

logic 0 = disable the receiver line status interrupt (normal default condition)

logic 1 = enable the receiver line status interrupt

Transmit Holding Register interrupt. This interrupt will be issued whenever the

THR is empty, and is associated with LSR[1].

logic 0 = disable the transmitter empty interrupt (normal default condition)

logic 1 = enable the transmitter empty interrupt

0

IER[0]

Receive Holding Register interrupt. This interrupt will be issued when the FIFO

has reached the programmed trigger level, or is cleared when the FIFO drops

below the trigger level in the FIFO mode of operation.

logic 0 = disable the receiver ready interrupt (normal default condition)

logic 1 = enable the receiver ready interrupt

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

28 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

7.2.1 IER versus Receive FIFO interrupt mode operation

When the receive FIFO (FCR[0] = logic 1), and receive interrupts (IER[0] = logic 1) are

enabled, the receive interrupts and register status will reﬂect the following:

• The receive data available interrupts are issued to the external CPU when the FIFO

has reached the programmed trigger level. It will be cleared when the FIFO drops

below the programmed trigger level.

• FIFO status will also be reﬂected in the user accessible ISR register when the FIFO

trigger level is reached. Both the ISR register status bit and the interrupt will be

cleared when the FIFO drops below the trigger level.

• The data ready bit (LSR[0]) is set as soon as a character is transferred from the shift

register to the receive FIFO. It is reset when the FIFO is empty.

7.2.2 IER versus Receive/Transmit FIFO polled mode operation

When FCR[0] = logic 1, resetting IER[0:3] enables the SC16C554B/554DB in the FIFO

polled mode of operation. Since the receiver and transmitter have separate bits in the

LSR, either or both can be used in the polled mode by selecting respective transmit or

receive control bit(s).

• LSR[0] will be a logic 1 as long as there is one byte in the receive FIFO.

• LSR[1:4] will provide the type of errors encountered, if any.

• LSR[5] will indicate when the transmit FIFO is empty.

• LSR[6] will indicate when both the transmit FIFO and Transmit Shift Register are

empty.

• LSR[7] will indicate any FIFO data errors.

7.3 FIFO Control Register (FCR)

This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger

levels, and select the DMA mode.

7.3.1 DMA mode

7.3.1.1 Mode 0 (FCR bit 3 = 0)

Set and enable the interrupt for each single transmit or receive operation, and is similar to

the 16C454 mode. Transmit Ready (TXRDY) will go to a logic 0 whenever an empty

transmit space is available in the Transmit Holding Register (THR). Receive Ready

(RXRDY) will go to a logic 0 whenever the Receive Holding Register (RHR) is loaded with

a character.

7.3.1.2 Mode 1 (FCR bit 3 = 1)

Set and enable the interrupt in a block mode operation. The transmit interrupt is set when

there are one or more FIFO locations empty. The receive interrupt is set when the receive

FIFO ﬁlls to the programmed trigger level. However, the FIFO continues to ﬁll regardless

of the programmed level until the FIFO is full. RXRDY remains a logic 0 as long as the

FIFO ﬁll level is above the programmed trigger level.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

29 of 56

SC16C554B/554DB

Philips Semiconductors

7.3.2 FIFO mode

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Table 11: FIFO Control Register bits description

Bit

Symbol

Description

7:6

FCR[7:6]

RCVR trigger. These bits are used to set the trigger level for the receive

FIFO interrupt.

An interrupt is generated when the number of characters in the FIFO equals

the programmed trigger level. However, the FIFO will continue to be loaded

until it is full. Refer to Table 12.

5:4

3

FCR[5:4]

FCR[3]

not used; initialized to logic 0

DMA mode select.

logic 0 = set DMA mode ‘0’ (normal default condition)

logic 1 = set DMA mode ‘1’

Transmit operation in mode ‘0’: When the SC16C554B/554DB is in the

16C450 mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode

(FIFOs enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there are no

characters in the transmit FIFO or Transmit Holding Register, the TXRDY pin

will be a logic 0. Once active, the TXRDY pin will go to a logic 1 after the ﬁrst

character is loaded into the Transmit Holding Register.

Receive operation in mode ‘0’: When the SC16C554B/554DB is in

mode ‘0’ (FCR[0] = logic 0), or in the FIFO mode (FCR[0] = logic 1; FCR[3] =

logic 0) and there is at least one character in the receive FIFO, the RXRDY

pin will be a logic 0. Once active, the RXRDY pin will go to a logic 1 when

there are no more characters in the receiver.

Transmit operation in mode ‘1’: When the SC16C554B/554DB is in FIFO

mode (FCR[0] = logic 1; FCR[3] = logic 1), the TXRDY pin will be a logic 1

when the transmit FIFO is completely full. It will be a logic 0 if one or more

FIFO locations are empty.

Receive operation in mode ‘1’: When the SC16C554B/554DB is in FIFO

mode (FCR[0] = logic 1; FCR[3] = logic 1) and the trigger level has been

reached, or a Receive Time-out has occurred, the RXRDY pin will go to a

logic 0. Once activated, it will go to a logic 1 after there are no more

characters in the FIFO.

2

1

0

FCR[2]

FCR[1]

FCR[0]

XMIT FIFO reset.

logic 0 = no FIFO transmit reset (normal default condition)

logic 1 = clears the contents of the transmit FIFO and resets the FIFO

counter logic (the Transmit Shift Register is not cleared or altered). This bit

will return to a logic 0 after clearing the FIFO.

RCVR FIFO reset.

logic 0 = no FIFO receive reset (normal default condition)

logic 1 = clears the contents of the receive FIFO and resets the FIFO

counter logic (the Receive Shift Register is not cleared or altered). This bit

will return to a logic 0 after clearing the FIFO.

FIFO enable.

logic 0 = disable the transmit and receive FIFO (normal default condition)

logic 1 = enable the transmit and receive FIFO. This bit must be a 1

when other FCR bits are written to, or they will not be programmed.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

30 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Table 12: RCVR trigger levels

FCR[7]

FCR[6]

RX FIFO trigger level

0

1

0

1

0

1

4

8

14

7.4 Interrupt Status Register (ISR)

The SC16C554B/554DB provides four levels of prioritized interrupts to minimize external

software interaction. The Interrupt Status Register (ISR) provides the user with four

interrupt status bits. Performing a read cycle on the ISR will provide the user with the

highest pending interrupt level to be serviced. No other interrupts are acknowledged until

the pending interrupt is serviced. Whenever the Interrupt Status Register is read, the

interrupt status is cleared. However, it should be noted that only the current pending

interrupt is cleared by the read. A lower level interrupt may be seen after re-reading the

interrupt status bits. Table 13 “Interrupt source” shows the data values (bits 0 to 5) for the

four prioritized interrupt levels and the interrupt sources associated with each of these

interrupt levels.

Table 13: Interrupt source

Priority

level

ISR[5] ISR[4] ISR[3] ISR[2] ISR[1] ISR[0] Source of the interrupt

1

2

3

4

0

1

0

1

0

1

0

1

0

LSR (Receiver Line Status

Register)

RXRDY (Receive Data

Ready)

RXRDY (Receive Data

time-out)

TXRDY (Transmitter Holding

Register Empty)

MSR (Modem Status

Register)

Table 14: Interrupt Status Register bits description

Bit

Symbol

Description

7:6

ISR[7:6]

FIFOs enabled. These bits are set to a logic 0 when the FIFO is not

being used. They are set to a logic 1 when the FIFOs are enabled.

logic 0 or cleared = default condition

Reserved; set to 0.

5:4

3:1

ISR[5:4]

ISR[3:1]

INT priority bits 2 to 0. These bits indicate the source for a pending

interrupt at interrupt priority levels 1, 2, and 3 (see Table 13).

logic 0 or cleared = default condition

INT status.

0

ISR[0]

logic 0 = an interrupt is pending and the ISR contents may be used

as a pointer to the appropriate interrupt service routine

logic 1 = no interrupt pending (normal default condition)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

31 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

7.5 Line Control Register (LCR)

The Line Control Register is used to specify the asynchronous data communication

format. The word length, the number of stop bits, and the parity are selected by writing the

appropriate bits in this register.

Table 15: Line Control Register bits description

Bit

Symbol

Description

7

LCR[7]

Divisor latch enable. The internal baud rate counter latch and

Enhance Feature mode enable.

logic 0 = divisor latch disabled (normal default condition)

logic 1 = divisor latch enabled

6

5

LCR[6]

LCR[5]

Set break. When enabled, the Break control bit causes a break

condition to be transmitted (the TX output is forced to a logic 0 state).

This condition exists until disabled by setting LCR[6] to a logic 0.

logic 0 = no TX break condition (normal default condition)

logic 1 = forces the transmitter output (TX) to a logic 0 for alerting

the remote receiver to a line break condition

Set parity. If the parity bit is enabled, LCR[5] selects the forced parity

format. Programs the parity conditions (see Table 16).

logic 0 = parity is not forced (normal default condition)

LCR[5] = logic 1 and LCR[4] = logic 0: parity bit is forced to a

logical 1 for the transmit and receive data

LCR[5] = logic 1 and LCR[4] = logic 1: parity bit is forced to a

logical 0 for the transmit and receive data

4

LCR[4]

Even parity. If the parity bit is enabled with LCR[3] set to a logic 1,

LCR[4] selects the even or odd parity format.

logic 0 = odd parity is generated by forcing an odd number of

logic 1s in the transmitted data. The receiver must be programmed

to check the same format (normal default condition).

logic 1 = even parity is generated by forcing an even number of

logic 1s in the transmitted data. The receiver must be programmed

to check the same format.

3

LCR[3]

Parity enable. Parity or no parity can be selected via this bit.

logic 0 = no parity (normal default condition)

logic 1 = a parity bit is generated during the transmission, receiver

checks the data and parity for transmission errors

2

LCR[2]

Stop bits. The length of stop bit is speciﬁed by this bit in conjunction

with the programmed word length (see Table 17).

logic 0 or cleared = default condition

1:0

LCR[1:0]

Word length bits 1, 0. These two bits specify the word length to be

transmitted or received (see Table 18).

logic 0 or cleared = default condition

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

32 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Table 16: LCR[5] parity selection

LCR[5]

LCR[4]

LCR[3]

Parity selection

no parity

X

0

1

X

0

1

0

1

0

1

odd parity

even parity

forced parity ‘1’

forced parity ‘0’

Table 17: LCR[2] stop bit length

LCR[2]

Word length (bits) Stop bit length (bit times)

0

1

5, 6, 7, 8

5

1

1¹⁄₂

6, 7, 8

2

Table 18: LCR[1:0] word length

LCR[1]

LCR[0]

Word length (bits)

0

1

0

1

0

1

5

6

7

8

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

33 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

7.6 Modem Control Register (MCR)

This register controls the interface with the modem or a peripheral device.

Table 19: Modem Control Register bits description

Bit

7:6

5

Symbol

MCR[7:6]

MCR[5]

MCR[4]

Description

Reserved; set to ‘0’.

Autoﬂow control enable.

4

Loop-back. Enable the local loop-back mode (diagnostics). In this mode

the transmitter output (TX) and the receiver input (RX), CTS, DSR, CD,

and RI are disconnected from the SC16C554B/554DB I/O pins. Internally

the modem data and control pins are connected into a loop-back data

conﬁguration (see Figure 14). In this mode, the receiver and transmitter

interrupts remain fully operational. The Modem Control Interrupts are also

operational, but the interrupts’ sources are switched to the lower four bits

of the Modem Control. Interrupts continue to be controlled by the IER

register.

logic 0 = disable loop-back mode (normal default condition)

logic 1 = enable local loop-back mode (diagnostics)

3

MCR[3]

OP2, INTx enable. Used to control the modem CD signal in the loop-back

mode.

logic 0 = forces INTA to INTD outputs to the 3-state mode during the

16 mode (normal default condition). In the loop-back mode, sets OP2

(CD) internally to a logic 1.

logic 1 = forces the INTA to INTD outputs to the active mode during the

16 mode. In the loop-back mode, sets OP2 (CD) internally to a logic 0.

2

1

MCR[2]

MCR[1]

OP1. This bit is used in the Loop-back mode only. In the loop-back mode,

this bit is used to write the state of the modem RI interface signal via OP1.

RTS

logic 0 = force RTS output to a logic 1 (normal default condition)

logic 1 = force RTS output to a logic 0

Automatic RTS may be used for hardware ﬂow control by enabling

MCR[5].

0

MCR[0]

DTR

logic 0 = force DTR output to a logic 1 (normal default condition)

logic 1 = force DTR output to a logic 0

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

34 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

7.7 Line Status Register (LSR)

This register provides the status of data transfers between the SC16C554B/554DB and

the CPU.

Table 20: Line Status Register bits description

Bit

Symbol Description

7

LSR[7]

FIFO data error.

logic 0 = no error (normal default condition)

logic 1 = at least one parity error, framing error or break indication is in the

current FIFO data. This bit is cleared when LSR register is read.

6

5

LSR[6]

THR and TSR empty. This bit is the Transmit Empty indicator. This bit is set to a

logic 1 whenever the Transmit Holding Register and the Transmit Shift Register

are both empty. It is reset to logic 0 whenever either the THR or TSR contains a

data character. In the FIFO mode, this bit is set to ‘1’ whenever the transmit

FIFO and Transmit Shift Register are both empty.

LSR[5]

THR empty. This bit is the Transmit Holding Register Empty indicator. This bit

indicates that the UART is ready to accept a new character for transmission. In

addition, this bit causes the UART to issue an interrupt to CPU when the THR

interrupt enable is set. The THR bit is set to a logic 1 when a character is

transferred from the Transmit Holding Register into the Transmitter Shift

Register. The bit is reset to a logic 0 concurrently with the loading of the

transmitter holding register by the CPU. In the FIFO mode, this bit is set when

the transmit FIFO is empty; it is cleared when at least 1 byte is written to the

transmit FIFO.

4

3

2

1

LSR[4]

LSR[3]

LSR[2]

LSR[1]

Break interrupt.

logic 0 = no break condition (normal default condition)

logic 1 = the receiver received a break signal (RX was a logic 0 for one

character frame time). In the FIFO mode, only one break character is loaded

into the FIFO.

Framing error.

logic 0 = no framing error (normal default condition)

logic 1 = framing error. The receive character did not have a valid stop bit(s).

In the FIFO mode, this error is associated with the character at the top of the

FIFO.

Parity error.

logic 0 = no parity error (normal default condition)

logic 1 = parity error. The receive character does not have correct parity

information and is suspect. In the FIFO mode, this error is associated with the

character at the top of the FIFO.

Overrun error.

logic 0 = no overrun error (normal default condition)

logic 1 = overrun error. A data overrun error occurred in the Receive Shift

Register. This happens when additional data arrives while the FIFO is full. In

this case, the previous data in the shift register is overwritten. Note that under

this condition, the data byte in the Receive Shift Register is not transferred

into the FIFO, therefore the data in the FIFO is not corrupted by the error.

0

LSR[0]

Receive data ready.

logic 0 = no data in Receive Holding Register or FIFO (normal default

condition)

logic 1 = data has been received and is saved in the Receive Holding

Register or FIFO

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

35 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

7.8 Modem Status Register (MSR)

This register provides the current state of the control interface signals from the modem, or

other peripheral device to which the SC16C554B/554DB is connected. Four bits of this

register are used to indicate the changed information. These bits are set to a logic 1

whenever a control input from the modem changes state. These bits are set to a logic 0

whenever the CPU reads this register.

Table 21: Modem Status Register bits description

Bit

Symbol

Description

7

MSR[7]

CD (active HIGH, logical 1). Normally this bit is the complement of the CD

input. In the Loop-back mode this bit is equivalent to the OP2 bit in the MCR

register.

6

5

4

MSR[6]

MSR[5]

MSR[4]

RI (active HIGH, logical 1). Normally this bit is the complement of the RI

input. In the Loop-back mode this bit is equivalent to the OP1 bit in the MCR

register.

DSR (active HIGH, logical 1). Normally this bit is the complement of the DSR

input. In Loop-back mode this bit is equivalent to the DTR bit in the MCR

register.

CTS (active HIGH, logical 1). CTS functions as hardware ﬂow control signal

input if it is enabled via MCR[5]. Flow control (when enabled) allows starting

and stopping the transmissions based on the external modem CTS signal. A

logic 1 at the CTS pin will stop SC16C554B/554DB transmissions as soon

as current character has ﬁnished transmission. Normally MSR[4] is the

complement of the CTS input. However, in the loop-back mode, this bit is

equivalent to the RTS bit in the MCR register.

[1]

3

MSR[3]

∆CD

Logic 0 = No CD change (normal default condition).

Logic 1 = The CD input to the SC16C554B/554DB has changed state

since the last time it was read. A modem Status Interrupt will be

generated.

[1]

2

1

MSR[2]

MSR[1]

∆RI

Logic 0 = No RI change (normal default condition).

Logic 1 = The RI input to the SC16C554B/554DB has changed from a

logic 0 to a logic 1. A modem Status Interrupt will be generated.

[1]

∆DSR

Logic 0 = No DSR change (normal default condition).

Logic 1 = The DSR input to the SC16C554B/554DB has changed state

since the last time it was read. A modem Status Interrupt will be

generated.

[1]

0

MSR[0]

∆CTS

Logic 0 = No CTS change (normal default condition).

Logic 1 = The CTS input to the SC16C554B/554DB has changed state

since the last time it was read. A modem Status Interrupt will be

generated.

[1] Whenever any MSR[3:0] is set to logic 1, a Modem Status Interrupt will be generated.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

36 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

7.9 Scratchpad Register (SPR)

The SC16C554B/554DB provides a temporary data register to store 8 bits of user

information.

7.10 SC16C554B/554DB external reset conditions

Table 22: Reset state for registers

Register

IER

Reset state

IER[7:0] = 0

ISR

ISR[7:1] = 0; ISR[0] = 1

LCR[7:0] = 0

LCR

MCR

LSR

MCR[7:0] = 0

LSR[7] = 0; LSR[6:5] = 1; LSR[4:0] = 0

MSR[7:4] = input signals; MSR[3:0] = 0

FCR[7:0] = 0

MSR

FCR

Table 23: Reset state for outputs

Output

Reset state

HIGH

TXA, TXB, TXC, TXD

RTSA, RTSB, RTSC, RTSD

DTRA, DTRB, DTRC, DTRD

RXRDY

HIGH

TXRDY

LOW

8. Limiting values

Table 24: Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol

V_CC

Parameter

Conditions

Min

Max

7

Unit

V

supply voltage

-

V_n

voltage at any pin

ambient temperature

storage temperature

GND − 0.3

V_CC+ 0.3

+85

V

T_amb

−40

−65

-

°C

mW

T_stg

+150

500

P_tot(pack)

total power dissipation per

package

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

37 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

9. Static characteristics

Table 25: Static characteristics

T_amb= −40 °C to +85 °C; tolerance of V_CC= ± 10 %, unless otherwise speciﬁed.

Symbol Parameter

Conditions

V_CC= 2.5 V

V_CC= 3.3 V

V_CC= 5.0 V

Unit

Min Typ Max Min Typ Max Min Typ Max

V_IL(CK)

V_IH(CK)

V_IL

LOW-level clock input

voltage

−0.3

-

+0.45 −0.3

V_CC2.4

+0.65 −0.3

-

+0.6 −0.5

V_CC3.0

+0.8 −0.5

-

+0.6

V

HIGH-level clock input

voltage

1.8

V_CC

LOW-level input voltage

(except XTAL1 clock)

−0.3

+0.8

V_IH

HIGH-level input voltage

(except XTAL1 clock)

1.6

-

2.0

-

2.2

-

V_OL

LOW-level output

voltage on all outputs ^[1](data bus)

I_OL= 5 mA

-

0.4

I_OL= 4 mA

(other outputs)

-

0.4

-

I_OL= 2 mA

(data bus)

-

0.4

-

I_OL= 1.6 mA

(other outputs)

-

0.4

-

V_OH

HIGH-level output

voltage

I_OH= −5 mA

(data bus)

-

2.4

I_OH= −1 mA

(other outputs)

-

2.0

-

I_OH= −800 µA

(data bus)

1.85

-

I_OH= −400 µA

(other outputs)

-

I_LIL

LOW-level input leakage

current

±10

±10 µA

±30 µA

I_CL

clock leakage

-

±30

4.5

5

-

±30

-

I_CC

supply current

input capacitance

f = 5 MHz

-

6

5

-

6

5

-

mA

pF

C_i

-

R_pu(int)

internal pull-up

resistance^[2]

500

-

500

kΩ

[1] Except XTAL2, V_OL= 1 V typical.

[2] Refer to Table 2 “Pin description” on page 10 for a listing of pins having internal pull-up resistors.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

38 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

10. Dynamic characteristics

Table 26: Dynamic characteristics

T_amb= −40 °C to +85 °C; tolerance of V_CC± 10 %, unless otherwise speciﬁed.

Symbol Parameter

Conditions

V_CC= 2.5 V

Min Max

V_CC= 3.3 V

Min Max

V_CC= 5.0 V

Min Max

Unit

t_1w, t_2wclock pulse duration

10

-

6

-

6

-

ns

[1] [2]

f_XTAL

t_6s

oscillator/clock frequency

address setup time

48

-

80

-

80

-

MHz

ns

0

t_6h

address hold time

0

-

0

-

0

-

ns

t_7d

IOR delay from chip select

IOR strobe width

10

77

0

-

10

26

0

-

10

23

0

-

ns

t_7w

t_7h

25 pF load

-

ns

chip select hold time from

IOR

-

ns

t_9d

read cycle delay

25 pF load

20

-

20

-

20

-

ns

t_12d

t_12h

t_13d

delay from IOR to data

data disable time

77

15

-

26

15

-

23

15

-

IOW delay from chip

select

10

t_13w

t_13h

IOW strobe width

20

0

-

20

0

-

15

0

-

ns

chip select hold time from

IOW

t_15d

t_16s

t_16h

t_17d

t_18d

write cycle delay

data setup time

data hold time

25

20

15

-

25

20

5

-

20

15

5

-

ns

-

delay from IOW to output 25 pF load

100

-

33

24

-

29

23

delay to set interrupt from 25 pF load

modem input

-

t_19d

t_20d

t_21d

t_22d

t_23d

t_24d

t_25d

t_26d

t_27d

delay to reset interrupt

from IOR

25 pF load

-

100

-

24

-

23

ns

delay from stop to set

interrupt

1T_RCLK

[3]

1T_RCLK

[3]

1T_RCLK

[3]

delay from IOR to

reset interrupt

25 pF load

100

29

45

28

40

delay from start to

set interrupt

delay from IOW to

transmit start

8T_RCLK24T_RCLK8T_RCLK24T_RCLK8T_RCLK24T_RCLKns

[3]

delay from IOW to

reset interrupt

-

100

-

45

-

40

ns

delay from stop to

set RXRDY

-

1T_RCLK

[3]

-

1T_RCLK

[3]

-

1T_RCLK

[3]

delay from IOR to

reset RXRDY

100

45

40

delay from IOW to

set TXRDY

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

39 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

Table 26: Dynamic characteristics …continued

T_amb= −40 °C to +85 °C; tolerance of V_CC± 10 %, unless otherwise speciﬁed.

Symbol Parameter

Conditions

V_CC= 2.5 V

V_CC= 3.3 V

V_CC= 5.0 V

Unit

Min

Max

Min

Max

Min

Max

t_28d

delay from start to reset

TXRDY

-

8T_RCLK

[3]

-

8T_RCLK

[3]

-

8T_RCLK

[3]

ns

t_30s

t_30w

t_30h

t_30d

t_31d

t_31h

t_32s

t_32h

t_32d

t_33s

t_33h

t_RESET

N

address setup time

chip select strobe width

address hold time

read cycle delay

delay from CS to data

data disable time

write strobe setup time

write strobe hold time

write cycle delay

data setup time

10

90

15

20

-

10

26

15

20

-

10

23

15

20

-

ns

[1]

25 pF load

-

25 pF load

-

90

26

23

-

15

-

15

-

15

10

25

20

15

200

1

-

10

25

15

5

-

10

20

15

5

-

data hold time

-

RESET pulse width

baud rate divisor

-

40

1

-

40

1

-

(2¹⁶− 1)

[1] Applies to external clock, crystal oscillator max 24 MHz.

1

t_3w

[2] Maximum frequency =

-------

[3] RCLK is an internal signal derived from Divisor Latch LSB (DLL) and Divisor Latch MSB (DLM) divisor latches.

10.1 Timing diagrams

A0 to A4

t

30h

t

30w

30s

t

30d

CS

R/W

t

31h

32s

t

31d

D0 to D7

002aaa210

Fig 18. General read timing in 68 mode

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

40 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

A0 to A4

t

30h

30s

30w

CS

R/W

t

32d

32s

32h

t

33h

t

33s

D0 to D7

002aaa211

Fig 19. General write timing in 68 mode

t

6h

valid

address

A0 to A2

t

13h

6s

active

CS

t

13d

15d

t

13w

IOW

active

t

16h

t

16s

D0 to D7

data

002aaa171

Fig 20. General write timing in 16 mode

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

41 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

t

6h

7h

valid

address

A0 to A2

t

6s

active

CS

IOR

t

7d

9d

t

7w

active

t

12h

12d

D0 to D7

data

002aaa172

Fig 21. General read timing in 16 mode

active

IOW

t

17d

RTS

DTR

change of state

CD

CTS

DSR

change of state

t

18d

INT

active

t

19d

active

IOR

t

18d

change of state

RI

002aaa352

Fig 22. Modem input/output timing

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

42 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

t

1w

2w

EXTERNAL

CLOCK

002aaa112

t

3w

1

t_3w

f _XTAL

=

-------

Fig 23. External clock timing

start

bit

parity stop start

bit

data bits (0 to 7)

D3 D4

RX

D0

D1

D2

D5

D6

D7

5 data bits

6 data bits

7 data bits

t

20d

active

INT

t

21d

active

IOR

16 baud rate clock

002aaa113

Fig 24. Receive timing

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

43 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

start

bit

parity stop start

bit

data bits (0 to 7)

D3 D4

D0

D1

D2

D5

D6

D7

RX

t

25d

active data

ready

RXRDY

IOR

t

26d

active

002aab063

Fig 25. Receive ready timing in non-FIFO mode

start

bit

parity stop

bit bit

data bits (0 to 7)

D3 D4

D0

D1

D2

D5

D6

D7

RX

first byte that

reaches the

trigger level

t

25d

active data

ready

RXRDY

IOR

t

26d

active

002aab064

Fig 26. Receive ready timing in FIFO mode

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

44 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

start

bit

parity stop start

bit

data bits (0 to 7)

TX

D0

D1

D2

D3

D4

D5

D6

D7

5 data bits

6 data bits

7 data bits

active

INT

transmitter ready

t

22d

t

24d

t

23d

active

IOW

active

16 baud rate clock

002aaa116

Fig 27. Transmit timing

start

bit

parity stop start

bit bit

bit

data bits (0 to 7)

D3 D4

D0

D1

D2

D5

D6

D7

TX

IOW

active

t

28d

D0 to D7

byte #1

t

27d

active transmitter

ready

TXRDY

transmitter

not ready

002aab062

Fig 28. Transmit ready timing in non-FIFO mode

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

45 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

start

bit

parity stop

bit

data bits (0 to 7)

D3 D4

D0

D1

D2

D5

D6

D7

TX

5 data bits

6 data bits

7 data bits

IOW

active

t

28d

D0 to D7

byte #16

t

27d

TXRDY

FIFO full

002aab061

Fig 29. Transmit ready timing in FIFO mode (DMA mode ‘1’)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

46 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

11. Package outline

LQFP64: plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm

SOT314-2

y

X

A

48

33

Z

49

32

E

e

H

A

E

2

E

A

(A )

3

A

1

w M

p

θ

b

L

p

pin 1 index

L

64

17

detail X

1

16

Z

v M

D

A

e

w M

b

p

D

B

H

v M

B

D

0

2.5

scale

5 mm

DIMENSIONS (mm are the original dimensions)

A

(1)

UNIT

A

b

c

D

E

e

H

L

v

w

y

Z

E

θ

1

2

3

p

D

E

p

D

max.

7^o

0^o

0.20 1.45

0.05 1.35

0.27 0.18 10.1 10.1

0.17 0.12 9.9 9.9

12.15 12.15

11.85 11.85

0.75

0.45

1.45 1.45

1.05 1.05

1.6

mm

0.25

0.5

1

0.2 0.12 0.1

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

REFERENCES

OUTLINE

EUROPEAN

PROJECTION

ISSUE DATE

VERSION

IEC

JEDEC

JEITA

00-01-19

03-02-25

SOT314-2

136E10

MS-026

Fig 30. Package outline SOT314-2 (LQFP64)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

47 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

LQFP80: plastic low profile quad flat package; 80 leads; body 12 x 12 x 1.4 mm

SOT315-1

y

X

A

60

41

Z

61

40

E

e

H

A

E

2

E

A

(A )

3

A

1

w M

p

θ

b

L

p

L

pin 1 index

80

21

detail X

1

20

Z

D

v

M

A

e

w M

b

p

D

B

H

v

M

B

D

0

5

10 mm

scale

DIMENSIONS (mm are the original dimensions)

A

(1)

UNIT

A

b

c

D

E

e

H

L

v

w

y

Z

θ

1

2

3

p

D

E

p

D

E

max.

7^o

0^o

0.16 1.5

0.04 1.3

0.27 0.18 12.1 12.1

0.13 0.12 11.9 11.9

14.15 14.15

13.85 13.85

0.75

0.30

1.45 1.45

1.05 1.05

mm

1.6

0.25

0.5

1

0.2 0.15 0.1

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

REFERENCES

OUTLINE

EUROPEAN

PROJECTION

ISSUE DATE

VERSION

IEC

JEDEC

JEITA

00-01-19

03-02-25

SOT315-1

136E15

MS-026

Fig 31. Package outline SOT315-1 (LQFP80)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

48 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

LQFP64: plastic low profile quad flat package; 64 leads; body 7 x 7 x 1.4 mm

SOT414-1

y

X

A

48

33

49

32

Z

E

e

A

2

A

H

E

(A )

3

A

1

w M

p

θ

b

pin 1 index

L

p

L

64

17

detail X

1

16

Z

v M

A

D

e

w M

b

p

D

B

H

v M

B

D

0

2.5

scale

5 mm

DIMENSIONS (mm are the original dimensions)

A

(1)

UNIT

A

b

c

D

E

e

H

D

H

L

v

w

y

Z

θ

1

2

3

p

E

p

D

E

max.

7^o

0^o

0.15 1.45

0.05 1.35

0.23 0.20 7.1

0.13 0.09 6.9

7.1

6.9

9.15 9.15

8.85 8.85

0.75

0.45

0.64 0.64

0.36 0.36

1.6

mm

0.25

0.4

1

0.2 0.08 0.08

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

REFERENCES

OUTLINE

EUROPEAN

PROJECTION

ISSUE DATE

VERSION

IEC

JEDEC

JEITA

00-01-19

03-02-20

SOT414-1

136E06

MS-026

Fig 32. Package outline SOT414-1 (LQFP64)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

49 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

HVQFN48: plastic thermal enhanced very thin quad flat package; no leads;

48 terminals; body 6 x 6 x 0.85 mm

SOT778-3

D

B

A

terminal 1

index area

E

A

1

c

detail X

C

e

1

y

C

1

y

M

v

C

A

B

b

e

1/2 e

w

13

24

L

25

12

e

2

E

h

1/2 e

1

36

terminal 1

index area

48

37

X

D

h

0

2.5

scale

5 mm

DIMENSIONS (mm are the original dimensions)

(1)

A

(1)

UNIT

A

b

c

D

E

e

L

v

w

y

1

h

1

2

max

0.05 0.25

0.00 0.15

6.1

5.9

3.95

3.65

6.1

5.9

3.95

3.65

0.5

0.3

1

mm

0.2

0.4

4.4

0.1

0.05 0.05

0.1

Note

1. Plastic or metal protrusions of 0.075 mm maximum per side are not included

REFERENCES

OUTLINE

VERSION

EUROPEAN

PROJECTION

ISSUE DATE

IEC

JEDEC

JEITA

- - -

04-06-16

04-06-23

SOT778-3

- - -

Fig 33. Package outline SOT778-3 (HVQFN48)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

50 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

PLCC68: plastic leaded chip carrier; 68 leads

SOT188-2

e

E

D

y

X

A

60

44

Z

E

43

61

b

p

b

1

w

M

68

1

H

E

pin 1 index

A

e

A

1

A

4

(A )

3

L

p

9

k

27

β

detail X

10

26

v

M

A

e

Z

D

B

H

v

M

B

D

0

5

10 mm

scale

DIMENSIONS (mm dimensions are derived from the original inch dimensions)

(1)

A

Z

E

4

1

(1)

D

UNIT

mm

A

b

D

E

e

H

k

L

p

v

w

y

β

b

3

1

D

E

D

E

p

max.

min.

max. max.

4.57

4.19

0.81 24.33 24.33

0.66 24.13 24.13

23.62 23.62 25.27 25.27 1.22 1.44

22.61 22.61 25.02 25.02 1.07 1.02

0.53

0.33

0.51 0.25

3.3

1.27

0.05

0.18 0.18

0.1

2.16 2.16

o

45

0.180

0.165

0.032 0.958 0.958

0.026 0.950 0.950

0.93 0.93 0.995 0.995 0.048 0.057

0.89 0.89 0.985 0.985 0.042 0.040

0.021

0.013

inches

0.02 0.01 0.13

0.007 0.007 0.004 0.085 0.085

Note

1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.

REFERENCES

OUTLINE

EUROPEAN

PROJECTION

ISSUE DATE

VERSION

IEC

JEDEC

JEITA

99-12-27

01-11-14

SOT188-2

112E10

MS-018

EDR-7319

Fig 34. Package outline SOT188-2 (PLCC68)

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

51 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

12. Soldering

12.1 Introduction to soldering surface mount packages

This text gives a very brief insight to a complex technology. A more in-depth account of

soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages

(document order number 9398 652 90011).

There is no soldering method that is ideal for all surface mount IC packages. Wave

soldering can still be used for certain surface mount ICs, but it is not suitable for ﬁne pitch

SMDs. In these situations reﬂow soldering is recommended.

12.2 Reﬂow soldering

Reﬂow soldering requires solder paste (a suspension of ﬁne solder particles, ﬂux and

binding agent) to be applied to the printed-circuit board by screen printing, stencilling or

pressure-syringe dispensing before package placement. Driven by legislation and

environmental forces the worldwide use of lead-free solder pastes is increasing.

Several methods exist for reﬂowing; for example, convection or convection/infrared

heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)

vary between 100 seconds and 200 seconds depending on heating method.

Typical reﬂow peak temperatures range from 215 °C to 270 °C depending on solder paste

material. The top-surface temperature of the packages should preferably be kept:

• below 225 °C (SnPb process) or below 245 °C (Pb-free process)

– for all BGA, HTSSON..T and SSOP..T packages

– for packages with a thickness ≥ 2.5 mm

– for packages with a thickness < 2.5 mm and a volume ≥ 350 mm³so called

thick/large packages.

• below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with a

thickness < 2.5 mm and a volume < 350 mm³so called small/thin packages.

Moisture sensitivity precautions, as indicated on packing, must be respected at all times.

12.3 Wave soldering

Conventional single wave soldering is not recommended for surface mount devices

(SMDs) or printed-circuit boards with a high component density, as solder bridging and

non-wetting can present major problems.

To overcome these problems the double-wave soldering method was speciﬁcally

developed.

If wave soldering is used the following conditions must be observed for optimal results:

• Use a double-wave soldering method comprising a turbulent wave with high upward

pressure followed by a smooth laminar wave.

• For packages with leads on two sides and a pitch (e):

– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be

parallel to the transport direction of the printed-circuit board;

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

52 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the

transport direction of the printed-circuit board.

The footprint must incorporate solder thieves at the downstream end.

• For packages with leads on four sides, the footprint must be placed at a 45° angle to

the transport direction of the printed-circuit board. The footprint must incorporate

solder thieves downstream and at the side corners.

During placement and before soldering, the package must be ﬁxed with a droplet of

adhesive. The adhesive can be applied by screen printing, pin transfer or syringe

dispensing. The package can be soldered after the adhesive is cured.

Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 °C

or 265 °C, depending on solder material applied, SnPb or Pb-free respectively.

A mildly-activated ﬂux will eliminate the need for removal of corrosive residues in most

applications.

12.4 Manual soldering

Fix the component by ﬁrst soldering two diagonally-opposite end leads. Use a low voltage

(24 V or less) soldering iron applied to the ﬂat part of the lead. Contact time must be

limited to 10 seconds at up to 300 °C.

When using a dedicated tool, all other leads can be soldered in one operation within

2 seconds to 5 seconds between 270 °C and 320 °C.

12.5 Package related soldering information

Table 27: Suitability of surface mount IC packages for wave and reﬂow soldering methods

Package ^[1]

Soldering method

Wave

Reﬂow^[2]

BGA, HTSSON..T^[3], LBGA, LFBGA, SQFP,

SSOP..T^[3], TFBGA, VFBGA, XSON

not suitable

suitable

DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,

HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,

HVSON, SMS

not suitable^[4]

suitable

PLCC^[5], SO, SOJ

suitable

LQFP, QFP, TQFP

not recommended^{[5] [6]}

not recommended^[7]

not suitable

suitable

SSOP, TSSOP, VSO, VSSOP

CWQCCN..L^[8], PMFP^[9], WQCCN..L^[8]

suitable

not suitable

[1] For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026);

order a copy from your Philips Semiconductors sales ofﬁce.

[2] All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the

maximum temperature (with respect to time) and body size of the package, there is a risk that internal or

external package cracks may occur due to vaporization of the moisture in them (the so called popcorn

effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit

Packages; Section: Packing Methods.

[3] These transparent plastic packages are extremely sensitive to reﬂow soldering conditions and must on no

account be processed through more than one soldering cycle or subjected to infrared reﬂow soldering with

peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reﬂow oven. The package

body peak temperature must be kept as low as possible.

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

53 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

[4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the

solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink

on the top side, the solder might be deposited on the heatsink surface.

[5] If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave

direction. The package footprint must incorporate solder thieves downstream and at the side corners.

[6] Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is

deﬁnitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.

[7] Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger

than 0.65 mm; it is deﬁnitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.

[8] Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered

pre-mounted on ﬂex foil. However, the image sensor package can be mounted by the client on a ﬂex foil by

using a hot bar soldering process. The appropriate soldering proﬁle can be provided on request.

[9] Hot bar soldering or manual soldering is suitable for PMFP packages.

13. Abbreviations

Table 28: Abbreviations

Acronym

CPU

Description

Central Processing Unit

DMA

Direct Memory Access

FIFO

First In/First Out

ISDN

Integrated Service Digital Network

4-channel (Quad) Universal Asynchronous Receiver and Transmitter

Universal Asynchronous Receiver and Transmitter

QUART

UART

14. Revision history

Table 29: Revision history

Document ID

Release

date

Data sheet status Change Doc. number

notice

Supersedes

SC16C554B_554DB_3

Modiﬁcations:

20050901

Product data sheet

-

SC16C554B_554DB_3 SC16C554B_554DB_2

• Figure 6 “Pin conﬁguration for LQFP80” on page 8: corrected names for pins 31 through 40

(pins deﬁned in Table 2 “Pin description” are correct).

• Table 8 “Baud rate generator programming table using a 7.3728 MHz clock” on page 21:

added “(bit/s)” to ﬁrst column’s heading

• Table 17 “LCR[2] stop bit length” on page 33: added “(bits)” to second column’s heading

• Table 18 “LCR[1:0] word length” on page 33: added “(bits)” to third column’s heading

SC16C554B_554DB_2

SC16C554B_554DB_1

20050613

Product data sheet

-

9397 750 14966

SC16C554B_554DB_1

20050209

Product data sheet

-

9397 750 13133

-

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

54 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

15. Data sheet status

Level Data sheet status^[1]Product status^{[2] [3]}

Deﬁnition

I

Objective data

Development

This data sheet contains data from the objective speciﬁcation for product development. Philips

Semiconductors reserves the right to change the speciﬁcation in any manner without notice.

II

Preliminary data

Qualiﬁcation

This data sheet contains data from the preliminary speciﬁcation. Supplementary data will be published

at a later date. Philips Semiconductors reserves the right to change the speciﬁcation without notice, in

order to improve the design and supply the best possible product.

III

Product data

Production

This data sheet contains data from the product speciﬁcation. Philips Semiconductors reserves the

right to make changes at any time in order to improve the design, manufacturing and supply. Relevant

changes will be communicated via a Customer Product/Process Change Notiﬁcation (CPCN).

[1]

[2]

Please consult the most recently issued data sheet before initiating or completing a design.

The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at

URL http://www.semiconductors.philips.com.

[3]

For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.

customers using or selling these products for use in such applications do so

at their own risk and agree to fully indemnify Philips Semiconductors for any

damages resulting from such application.

16. Deﬁnitions

Short-form speciﬁcation — The data in a short-form speciﬁcation is

extracted from a full data sheet with the same type number and title. For

detailed information see the relevant data sheet or data handbook.

Right to make changes — Philips Semiconductors reserves the right to

make changes in the products - including circuits, standard cells, and/or

software - described or contained herein in order to improve design and/or

performance. When the product is in full production (status ‘Production’),

relevant changes will be communicated via a Customer Product/Process

Change Notiﬁcation (CPCN). Philips Semiconductors assumes no

responsibility or liability for the use of any of these products, conveys no

license or title under any patent, copyright, or mask work right to these

products, and makes no representations or warranties that these products are

free from patent, copyright, or mask work right infringement, unless otherwise

speciﬁed.

Limiting values deﬁnition — Limiting values given are in accordance with

the Absolute Maximum Rating System (IEC 60134). Stress above one or

more of the limiting values may cause permanent damage to the device.

These are stress ratings only and operation of the device at these or at any

other conditions above those given in the Characteristics sections of the

speciﬁcation is not implied. Exposure to limiting values for extended periods

may affect device reliability.

Application information — Applications that are described herein for any

of these products are for illustrative purposes only. Philips Semiconductors

make no representation or warranty that such applications will be suitable for

the speciﬁed use without further testing or modiﬁcation.

18. Trademarks

Notice — All referenced brands, product names, service names and

17. Disclaimers

trademarks are the property of their respective owners.

Life support — These products are not designed for use in life support

appliances, devices, or systems where malfunction of these products can

reasonably be expected to result in personal injury. Philips Semiconductors

19. Contact information

For additional information, please visit: http://www.semiconductors.philips.com

For sales ofﬁce addresses, send an email to: sales.addresses@www.semiconductors.philips.com

SC16C554B_554DB_3

Product data sheet

Rev. 03 — 1 September 2005

55 of 56

SC16C554B/554DB

Philips Semiconductors

5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs

20. Contents

1

2

3

4

General description . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Ordering information. . . . . . . . . . . . . . . . . . . . . 2

Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3

8

Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 37

Static characteristics . . . . . . . . . . . . . . . . . . . 38

Dynamic characteristics. . . . . . . . . . . . . . . . . 39

Timing diagrams. . . . . . . . . . . . . . . . . . . . . . . 40

Package outline . . . . . . . . . . . . . . . . . . . . . . . . 47

9

10

10.1

11

12

12.1

5

5.1

5.1.1

5.1.2

5.1.3

5.1.4

5.2

Pinning information. . . . . . . . . . . . . . . . . . . . . . 5

Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

PLCC68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

LQFP64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

LQFP80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

HVQFN48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pin description . . . . . . . . . . . . . . . . . . . . . . . . 10

Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Introduction to soldering surface mount

packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Reﬂow soldering. . . . . . . . . . . . . . . . . . . . . . . 52

Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 52

Manual soldering . . . . . . . . . . . . . . . . . . . . . . 53

Package related soldering information. . . . . . 53

12.2

12.3

12.4

12.5

6

6.1

6.1.1

6.1.2

6.2

Functional description . . . . . . . . . . . . . . . . . . 15

Interface options . . . . . . . . . . . . . . . . . . . . . . . 16

The 16 mode interface . . . . . . . . . . . . . . . . . . 16

The 68 mode interface . . . . . . . . . . . . . . . . . . 16

Internal registers. . . . . . . . . . . . . . . . . . . . . . . 17

FIFO operation . . . . . . . . . . . . . . . . . . . . . . . . 17

Autoﬂow control (see Figure 9). . . . . . . . . . . . 18

Auto-RTS (see Figure 9). . . . . . . . . . . . . . . . . 18

Auto-CTS (see Figure 9). . . . . . . . . . . . . . . . . 18

Enabling autoﬂow control and auto-CTS . . . . 19

Auto-CTS and auto-RTS functional timing . . . 19

Hardware/software and time-out interrupts. . . 20

Programmable baud rate generator . . . . . . . . 20

DMA operation . . . . . . . . . . . . . . . . . . . . . . . . 22

Loop-back mode. . . . . . . . . . . . . . . . . . . . . . . 22

13

14

15

16

17

18

19

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 54

Revision history . . . . . . . . . . . . . . . . . . . . . . . 54

Data sheet status. . . . . . . . . . . . . . . . . . . . . . . 55

Deﬁnitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Contact information . . . . . . . . . . . . . . . . . . . . 55

6.3

6.4

6.4.1

6.4.2

6.4.3

6.4.4

6.5

6.6

6.7

6.8

7

7.1

Register descriptions . . . . . . . . . . . . . . . . . . . 27

Transmit (THR) and Receive (RHR) Holding

Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Interrupt Enable Register (IER) . . . . . . . . . . . 28

IER versus Receive FIFO interrupt mode

7.2

7.2.1

operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

IER versus Receive/Transmit FIFO polled

7.2.2

mode operation. . . . . . . . . . . . . . . . . . . . . . . . 29

FIFO Control Register (FCR) . . . . . . . . . . . . . 29

DMA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Mode 0 (FCR bit 3 = 0). . . . . . . . . . . . . . . . . . 29

Mode 1 (FCR bit 3 = 1). . . . . . . . . . . . . . . . . . 29

FIFO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Interrupt Status Register (ISR) . . . . . . . . . . . . 31

Line Control Register (LCR) . . . . . . . . . . . . . . 32

Modem Control Register (MCR) . . . . . . . . . . . 34

Line Status Register (LSR). . . . . . . . . . . . . . . 35

Modem Status Register (MSR). . . . . . . . . . . . 36

Scratchpad Register (SPR) . . . . . . . . . . . . . . 37

SC16C554B/554DB external reset conditions 37

7.3

7.3.1

7.3.1.1

7.3.1.2

7.3.2

7.4

7.5

7.6

7.7

7.8

7.9

7.10

All rights are reserved. Reproduction in whole or in part is prohibited without the prior

written consent of the copyright owner. The information presented in this document does

not form part of any quotation or contract, is believed to be accurate and reliable and may

be changed without notice. No liability will be accepted by the publisher for any

consequence of its use. Publication thereof does not convey nor imply any license under

patent- or other industrial or intellectual property rights.

Date of release: 1 September 2005

Document number: SC16C554B_554DB_3

Published in The Netherlands


型号：	935279067157
厂家：	NXP
描述：	4 CHANNEL(S), 5Mbps, SERIAL COMM CONTROLLER, PQFP64, 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-414-1, LQFP-64 通信时钟数据传输外围集成电路
文件：	总56页 (文件大小：293K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

935279067157 [NXP]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E