935313549528 [NXP]
Microcontroller;型号: | 935313549528 |
厂家: | NXP |
描述: | Microcontroller 微控制器 外围集成电路 |
文件: | 总326页 (文件大小:4459K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Document Number: QFN_Addendum
Rev. 0, 07/2014
Freescale Semiconductor
Addendum
Addendum for New QFN
Package Migration
This addendum provides the changes to the 98A case outline numbers for products covered in this book.
Case outlines were changed because of the migration from gold wire to copper wire in some packages. See
the table below for the old (gold wire) package versus the new (copper wire) package.
To view the new drawing, go to Freescale.com and search on the new 98A package number for your
device.
For more information about QFN package use, see EB806: Electrical Connection Recommendations for
the Exposed Pad on QFN and DFN Packages.
© Freescale Semiconductor, Inc., 2014. All rights reserved.
Original (gold wire)
package document number package document number
Current (copper wire)
Part Number
Package Description
48 QFN
MC68HC908JW32
MC9S08AC16
MC9S908AC60
MC9S08AC128
MC9S08AW60
MC9S08GB60A
MC9S08GT16A
MC9S08JM16
MC9S08JM60
MC9S08LL16
MC9S08QE128
MC9S08QE32
MC9S08RG60
MCF51CN128
MC9RS08LA8
MC9S08GT16A
MC9S908QE32
MC9S908QE8
MC9S08JS16
MC9S08QB8
98ARH99048A
98ASA00466D
48 QFN
32 QFN
32 QFN
32 QFN
24 QFN
98ARL10606D
98ARH99035A
98ARE10566D
98ASA00071D
98ARL10608D
98ASA00466D
98ASA00473D
98ASA00473D
98ASA00736D
98ASA00734D
MC9S08QG8
MC9S08SH8
24 QFN
24 QFN
24 QFN
16 QFN
8 DFN
98ARL10605D
98ARE10714D
98ASA00087D
98ARE10614D
98ARL10557D
98ASA00474D
98ASA00474D
98ASA00602D
98ASA00671D
98ASA00672D
MC9RS08KB12
MC9S08QG8
MC9RS08KB12
MC9S08QG8
MC9RS08KA2
6 DFN
98ARL10602D
98ASA00735D
Addendum for New QFN Package Migration, Rev. 0
2
Freescale Semiconductor
MC9S08AW60
MC9S08AW48
MC9S08AW32
MC9S08AW16
Data Sheet
HCS08
Microcontrollers
MC9S08AW60
Rev 2
12/2006
freescale.com
MC9S08AW60 Features
•
•
IIC — Inter-integrated circuit bus module to
operate at up to 100 kbps with maximum bus
loading; capable of higher baud rates with
reduced loading
Timers — One 2-channel and one 6-channel
16-bit timer/pulse-width modulator (TPM)
module: Selectable input capture, output
compare, and edge-aligned PWM capability on
each channel. Each timer module may be
configured for buffered, centered PWM
(CPWM) on all channels
8-Bit HCS08 Central Processor Unit (CPU)
•
•
•
40-MHz HCS08 CPU (central processor unit)
20-MHz internal bus frequency
HC08 instruction set with added BGND
instruction
•
•
Single-wire background debug mode interface
Breakpoint capability to allow single breakpoint
setting during in-circuit debugging (plus two
more breakpoints in on-chip debug module)
•
On-chip real-time in-circuit emulation (ICE) with
two comparators (plus one in BDM), nine
trigger modes, and on-chip bus capture buffer.
Typically shows approximately 50 instructions
before or after the trigger point.
•
KBI — Up to 8-pin keyboard interrupt module
Input/Output
•
•
•
•
Up to 54 general-purpose input/output (I/O)
pins
Software-selectable pullups on ports when
used as inputs
Software-selectable slew rate control on ports
when used as outputs
•
Support for up to 32 interrupt/reset sources
Memory Options
•
Up to 60 KB of on-chip in-circuit programmable
FLASH memory with block protection and
security options
Software-selectable drive strength on ports
when used as outputs
•
Up to 2 KB of on-chip RAM
Clock Source Options
•
•
Master reset pin and power-on reset (POR)
Internal pullup on RESET, IRQ, and BKGD/MS
pins to reduce customer system cost
•
Clock source options include crystal, resonator,
external clock, or internally generated clock
with precision NVM trimming
Package Options
MC9S08AW60/48/32
System Protection
•
Optional computer operating properly (COP)
•
•
•
•
64-pin quad flat package (QFP)
reset
64-pin low-profile quad flat package (LQFP)
48-pin low-profile quad flat package (QFN)
44-pin low-profile quad flat package (LQFP)
•
•
•
Low-voltage detection with reset or interrupt
Illegal opcode detection with reset
Illegal address detection with reset (some
devices don’t have illegal addresses)
MC9S08AW16
•
•
48-pin low-profile quad flat package (QFN)
44-pin low-profile quad flat package (LQFP)
Power-Saving Modes
•
Wait plus two stops
Peripherals
•
ADC — Up to 16-channel, 10-bit
analog-to-digital converter with automatic
compare function
•
•
SCI — Two serial communications interface
modules with optional 13-bit break
SPI — Serial peripheral interface module
MC9S08AW60 Data Sheet
Covers: MC9S08AW60
MC9S08AW48
MC9S08AW32
MC9S08AW16
MC9S08AW60
Rev 2
12/2006
Revision History
To provide the most up-to-date information, the revision of our documents on the World Wide Web will be
the most current. Your printed copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://freescale.com/
The following revision history table summarizes changes contained in this document. For your
convenience, the page number designators have been linked to the appropriate location.
Revision
Number
Revision
Date
Description of Changes
1
1/2006
Initial external release.
Includes KBI block changes; new V / I figures; RI spec changes; SC part
OL OL
DD
numbers with ICG trim modifications; addition of Temp Sensor to ADC. Resolved
the stop IDD issues, added RTI figure, bandgap information, and incorporated
electricals edits and any ProjectSync issues.
2
12/2006
This product incorporates SuperFlash® technology licensed from SST.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
© Freescale Semiconductor, Inc., 2006. All rights reserved.
List of Chapters
Chapter
Title
Page
Chapter 1
Chapter 2
Chapter 3
Chapter 4
Chapter 5
Chapter 6
Chapter 7
Chapter 8
Chapter 9
Chapter 10
Chapter 11
Chapter 12
Chapter 13
Chapter 14
Chapter 15
Appendix A
Appendix B
Introduction......................................................................................19
Pins and Connections.....................................................................23
Modes of Operation.........................................................................33
Memory.............................................................................................39
Resets, Interrupts, and System Configuration .............................65
Parallel Input/Output .......................................................................81
Central Processor Unit (S08CPUV2)............................................109
Internal Clock Generator (S08ICGV4)..........................................129
Keyboard Interrupt (S08KBIV1)....................................................157
Timer/PWM (S08TPMV2) ...............................................................165
Serial Communications Interface (S08SCIV2).............................181
Serial Peripheral Interface (S08SPIV3) ........................................199
Inter-Integrated Circuit (S08IICV1)...............................................215
Analog-to-Digital Converter (S08ADC10V1)................................233
Development Support ...................................................................261
Electrical Characteristics and Timing Specifications ................283
Ordering Information and Mechanical Drawings........................309
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
7
Contents
Section Number
Title
Page
Chapter 1
Introduction
1.1 Overview .........................................................................................................................................19
1.2 MCU Block Diagrams .....................................................................................................................19
1.3 System Clock Distribution ..............................................................................................................21
Chapter 2
Pins and Connections
2.1 Introduction .....................................................................................................................................23
2.2 Device Pin Assignment ...................................................................................................................24
2.3 Recommended System Connections ...............................................................................................26
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.3.7
Power (V , 2 x V , V
, V
) .........................................................................28
DD
SS
DDAD
SSAD
Oscillator (XTAL, EXTAL) ............................................................................................28
RESET Pin ......................................................................................................................29
Background/Mode Select (BKGD/MS) .........................................................................29
ADC Reference Pins (V
, V
) ...........................................................................29
REFH
REFL
External Interrupt Pin (IRQ) ...........................................................................................29
General-Purpose I/O and Peripheral Ports .....................................................................30
Chapter 3
Modes of Operation
3.1 Introduction .....................................................................................................................................33
3.2 Features ...........................................................................................................................................33
3.3 Run Mode ........................................................................................................................................33
3.4 Active Background Mode ................................................................................................................33
3.5 Wait Mode .......................................................................................................................................34
3.6 Stop Modes ......................................................................................................................................34
3.6.1
3.6.2
3.6.3
3.6.4
3.6.5
Stop2 Mode ....................................................................................................................35
Stop3 Mode ....................................................................................................................36
Active BDM Enabled in Stop Mode ...............................................................................36
LVD Enabled in Stop Mode ...........................................................................................37
On-Chip Peripheral Modules in Stop Modes .................................................................37
Chapter 4
Memory
4.1 MC9S08AW60 Series Memory Map ..............................................................................................39
4.1.1
Reset and Interrupt Vector Assignments ........................................................................42
4.2 Register Addresses and Bit Assignments ........................................................................................43
4.3 RAM ................................................................................................................................................49
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
9
Section Number
Title
Page
4.4 FLASH ............................................................................................................................................50
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
Features ...........................................................................................................................51
Program and Erase Times ...............................................................................................51
Program and Erase Command Execution .......................................................................52
Burst Program Execution ...............................................................................................53
Access Errors ..................................................................................................................55
FLASH Block Protection ...............................................................................................55
Vector Redirection ..........................................................................................................56
4.5 Security ............................................................................................................................................56
4.6 FLASH Registers and Control Bits .................................................................................................58
4.6.1
4.6.2
4.6.3
4.6.4
4.6.5
4.6.6
FLASH Clock Divider Register (FCDIV) ......................................................................58
FLASH Options Register (FOPT and NVOPT) .............................................................59
FLASH Configuration Register (FCNFG) .....................................................................60
FLASH Protection Register (FPROT and NVPROT) ....................................................61
FLASH Status Register (FSTAT) ...................................................................................61
FLASH Command Register (FCMD) ............................................................................63
Chapter 5
Resets, Interrupts, and System Configuration
5.1 Introduction .....................................................................................................................................65
5.2 Features ...........................................................................................................................................65
5.3 MCU Reset ......................................................................................................................................65
5.4 Computer Operating Properly (COP) Watchdog .............................................................................66
5.5 Interrupts .........................................................................................................................................66
5.5.1
5.5.2
5.5.3
Interrupt Stack Frame .....................................................................................................67
External Interrupt Request (IRQ) Pin .............................................................................68
Interrupt Vectors, Sources, and Local Masks .................................................................69
5.6 Low-Voltage Detect (LVD) System ................................................................................................71
5.6.1
5.6.2
5.6.3
5.6.4
Power-On Reset Operation .............................................................................................71
LVD Reset Operation .....................................................................................................71
LVD Interrupt Operation ................................................................................................71
Low-Voltage Warning (LVW) ........................................................................................71
5.7 Real-Time Interrupt (RTI) ...............................................................................................................71
5.8 MCLK Output .................................................................................................................................72
5.9 Reset, Interrupt, and System Control Registers and Control Bits ...................................................72
5.9.1
5.9.2
5.9.3
5.9.4
5.9.5
5.9.6
5.9.7
Interrupt Pin Request Status and Control Register (IRQSC) .........................................73
System Reset Status Register (SRS) ...............................................................................74
System Background Debug Force Reset Register (SBDFR) ..........................................75
System Options Register (SOPT) ...................................................................................75
System MCLK Control Register (SMCLK) ...................................................................76
System Device Identification Register (SDIDH, SDIDL) ..............................................77
System Real-Time Interrupt Status and Control Register (SRTISC) .............................78
MC9S08AW60 Data Sheet, Rev 2
10
Freescale Semiconductor
Section Number
Title
Page
5.9.8
5.9.9
System Power Management Status and Control 1 Register (SPMSC1) .........................79
System Power Management Status and Control 2 Register (SPMSC2) .........................80
Chapter 6
Parallel Input/Output
6.1 Introduction .....................................................................................................................................81
6.2 Features ...........................................................................................................................................81
6.3 Pin Descriptions ..............................................................................................................................82
6.3.1
6.3.2
6.3.3
6.3.4
6.3.5
6.3.6
6.3.7
Port A ..............................................................................................................................82
Port B ..............................................................................................................................82
Port C ..............................................................................................................................83
Port D ..............................................................................................................................83
Port E ..............................................................................................................................84
Port F ..............................................................................................................................85
Port G ..............................................................................................................................85
6.4 Parallel I/O Control .........................................................................................................................86
6.5 Pin Control ......................................................................................................................................87
6.5.1
6.5.2
6.5.3
Internal Pullup Enable ....................................................................................................87
Output Slew Rate Control Enable ..................................................................................87
Output Drive Strength Select ..........................................................................................87
6.6 Pin Behavior in Stop Modes ............................................................................................................88
6.7 Parallel I/O and Pin Control Registers ............................................................................................88
6.7.1
6.7.2
6.7.3
6.7.4
6.7.5
6.7.6
6.7.7
6.7.8
6.7.9
Port A I/O Registers (PTAD and PTADD) .....................................................................88
Port A Pin Control Registers (PTAPE, PTASE, PTADS) ..............................................89
Port B I/O Registers (PTBD and PTBDD) .....................................................................91
Port B Pin Control Registers (PTBPE, PTBSE, PTBDS) ..............................................92
Port C I/O Registers (PTCD and PTCDD) .....................................................................94
Port C Pin Control Registers (PTCPE, PTCSE, PTCDS) ..............................................95
Port D I/O Registers (PTDD and PTDDD) ....................................................................97
Port D Pin Control Registers (PTDPE, PTDSE, PTDDS) .............................................98
Port E I/O Registers (PTED and PTEDD) ....................................................................100
6.7.10 Port E Pin Control Registers (PTEPE, PTESE, PTEDS) .............................................101
6.7.11 Port F I/O Registers (PTFD and PTFDD) ....................................................................103
6.7.12 Port F Pin Control Registers (PTFPE, PTFSE, PTFDS) ..............................................104
6.7.13 Port G I/O Registers (PTGD and PTGDD) ..................................................................106
6.7.14 Port G Pin Control Registers (PTGPE, PTGSE, PTGDS) ...........................................107
Chapter 7
Central Processor Unit (S08CPUV2)
7.1 Introduction ...................................................................................................................................109
7.1.1
Features .........................................................................................................................109
7.2 Programmer’s Model and CPU Registers .....................................................................................110
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
11
Section Number
Title
Page
7.2.1
7.2.2
7.2.3
7.2.4
7.2.5
Accumulator (A) ...........................................................................................................110
Index Register (H:X) ....................................................................................................110
Stack Pointer (SP) .........................................................................................................111
Program Counter (PC) ..................................................................................................111
Condition Code Register (CCR) ...................................................................................111
7.3 Addressing Modes .........................................................................................................................113
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.3.6
Inherent Addressing Mode (INH) ................................................................................113
Relative Addressing Mode (REL) ................................................................................113
Immediate Addressing Mode (IMM) ...........................................................................113
Direct Addressing Mode (DIR) ....................................................................................113
Extended Addressing Mode (EXT) ..............................................................................114
Indexed Addressing Mode ............................................................................................114
7.4 Special Operations .........................................................................................................................115
7.4.1
7.4.2
7.4.3
7.4.4
7.4.5
Reset Sequence .............................................................................................................115
Interrupt Sequence ........................................................................................................115
Wait Mode Operation ...................................................................................................116
Stop Mode Operation ...................................................................................................116
BGND Instruction ........................................................................................................117
7.5 HCS08 Instruction Set Summary ..................................................................................................118
Chapter 8
Internal Clock Generator (S08ICGV4)
8.1 Introduction ...................................................................................................................................131
8.1.1
8.1.2
8.1.3
Features .........................................................................................................................131
Modes of Operation ......................................................................................................132
Block Diagram ..............................................................................................................133
8.2 External Signal Description ..........................................................................................................133
8.2.1
8.2.2
8.2.3
8.2.4
EXTAL — External Reference Clock / Oscillator Input ..............................................133
XTAL — Oscillator Output ..........................................................................................133
External Clock Connections .........................................................................................134
External Crystal/Resonator Connections ......................................................................134
8.3 Register Definition ........................................................................................................................135
8.3.1
8.3.2
8.3.3
8.3.4
8.3.5
8.3.6
ICG Control Register 1 (ICGC1) .................................................................................135
ICG Control Register 2 (ICGC2) .................................................................................137
ICG Status Register 1 (ICGS1) ....................................................................................138
ICG Status Register 2 (ICGS2) ....................................................................................139
ICG Filter Registers (ICGFLTU, ICGFLTL) ...............................................................139
ICG Trim Register (ICGTRM) .....................................................................................140
8.4 Functional Description ..................................................................................................................140
8.4.1
8.4.2
8.4.3
Off Mode (Off) .............................................................................................................141
Self-Clocked Mode (SCM) ...........................................................................................141
FLL Engaged, Internal Clock (FEI) Mode ...................................................................142
MC9S08AW60 Data Sheet, Rev 2
12
Freescale Semiconductor
Section Number
Title
Page
8.4.4
8.4.5
8.4.6
8.4.7
8.4.8
8.4.9
FLL Engaged Internal Unlocked ..................................................................................143
FLL Engaged Internal Locked ......................................................................................143
FLL Bypassed, External Clock (FBE) Mode ...............................................................143
FLL Engaged, External Clock (FEE) Mode .................................................................143
FLL Lock and Loss-of-Lock Detection ........................................................................144
FLL Loss-of-Clock Detection ......................................................................................145
8.4.10 Clock Mode Requirements ...........................................................................................146
8.4.11 Fixed Frequency Clock .................................................................................................147
8.4.12 High Gain Oscillator .....................................................................................................147
8.5 Initialization/Application Information ..........................................................................................147
8.5.1
8.5.2
8.5.3
8.5.4
8.5.5
Introduction ..................................................................................................................147
Example #1: External Crystal = 32 kHz, Bus Frequency = 4.19 MHz ........................149
Example #2: External Crystal = 4 MHz, Bus Frequency = 20 MHz ............................151
Example #3: No External Crystal Connection, 5.4 MHz Bus Frequency ....................153
Example #4: Internal Clock Generator Trim ................................................................155
Chapter 9
Keyboard Interrupt (S08KBIV1)
9.1 Introduction ...................................................................................................................................157
9.2 Keyboard Pin Sharing ....................................................................................................................157
9.3 Features .........................................................................................................................................158
9.3.1
KBI Block Diagram ......................................................................................................160
9.4 Register Definition ........................................................................................................................160
9.4.1
9.4.2
KBI Status and Control Register (KBI1SC) .................................................................161
KBI Pin Enable Register (KBI1PE) .............................................................................162
9.5 Functional Description ..................................................................................................................162
9.5.1
9.5.2
9.5.3
Pin Enables ...................................................................................................................162
Edge and Level Sensitivity ...........................................................................................162
KBI Interrupt Controls .................................................................................................163
Chapter 10
Timer/PWM (S08TPMV2)
10.1 Introduction ...................................................................................................................................165
10.2 Features .........................................................................................................................................165
10.2.1 Features .........................................................................................................................167
10.2.2 Block Diagram ..............................................................................................................167
10.3 External Signal Description ..........................................................................................................169
10.3.1 External TPM Clock Sources .......................................................................................169
10.3.2 TPMxCHn — TPMx Channel n I/O Pins .....................................................................169
10.4 Register Definition ........................................................................................................................169
10.4.1 Timer x Status and Control Register (TPMxSC) ..........................................................170
10.4.2 Timer x Counter Registers (TPMxCNTH:TPMxCNTL) .............................................171
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
13
Section Number
Title
Page
10.4.3 Timer x Counter Modulo Registers (TPMxMODH:TPMxMODL) .............................172
10.4.4 Timer x Channel n Status and Control Register (TPMxCnSC) ....................................173
10.4.5 Timer x Channel Value Registers (TPMxCnVH:TPMxCnVL) ....................................174
10.5 Functional Description ..................................................................................................................175
10.5.1 Counter .........................................................................................................................175
10.5.2 Channel Mode Selection ...............................................................................................176
10.5.3 Center-Aligned PWM Mode ........................................................................................178
10.6 TPM Interrupts ..............................................................................................................................179
10.6.1 Clearing Timer Interrupt Flags .....................................................................................179
10.6.2 Timer Overflow Interrupt Description ..........................................................................179
10.6.3 Channel Event Interrupt Description ............................................................................180
10.6.4 PWM End-of-Duty-Cycle Events .................................................................................180
Chapter 11
Serial Communications Interface (S08SCIV2)
11.1 Introduction ...................................................................................................................................181
11.1.1 Features .........................................................................................................................183
11.1.2 Modes of Operation ......................................................................................................183
11.1.3 Block Diagram ..............................................................................................................183
11.2 Register Definition ........................................................................................................................185
11.2.1 SCI Baud Rate Registers (SCIxBDH, SCIxBHL) ........................................................186
11.2.2 SCI Control Register 1 (SCIxC1) .................................................................................187
11.2.3 SCI Control Register 2 (SCIxC2) .................................................................................188
11.2.4 SCI Status Register 1 (SCIxS1) ....................................................................................189
11.2.5 SCI Status Register 2 (SCIxS2) ....................................................................................191
11.2.6 SCI Control Register 3 (SCIxC3) .................................................................................191
11.2.7 SCI Data Register (SCIxD) ..........................................................................................192
11.3 Functional Description ..................................................................................................................192
11.3.1 Baud Rate Generation ...................................................................................................193
11.3.2 Transmitter Functional Description ..............................................................................193
11.3.3 Receiver Functional Description ..................................................................................194
11.3.4 Interrupts and Status Flags ...........................................................................................196
11.3.5 Additional SCI Functions .............................................................................................197
Chapter 12
Serial Peripheral Interface (S08SPIV3)
12.0.1 Features .........................................................................................................................201
12.0.2 Block Diagrams ............................................................................................................201
12.0.3 SPI Baud Rate Generation ............................................................................................203
12.1 External Signal Description ..........................................................................................................204
12.1.1 SPSCK — SPI Serial Clock .........................................................................................204
12.1.2 MOSI — Master Data Out, Slave Data In ....................................................................204
MC9S08AW60 Data Sheet, Rev 2
14
Freescale Semiconductor
Section Number
Title
Page
12.1.3 MISO — Master Data In, Slave Data Out ....................................................................204
12.1.4 SS — Slave Select ........................................................................................................204
12.2 Modes of Operation .......................................................................................................................205
12.2.1 SPI in Stop Modes ........................................................................................................205
12.3 Register Definition ........................................................................................................................205
12.3.1 SPI Control Register 1 (SPI1C1) ..................................................................................205
12.3.2 SPI Control Register 2 (SPI1C2) ..................................................................................206
12.3.3 SPI Baud Rate Register (SPI1BR) ...............................................................................207
12.3.4 SPI Status Register (SPI1S) ..........................................................................................208
12.3.5 SPI Data Register (SPI1D) ...........................................................................................209
12.4 Functional Description ..................................................................................................................210
12.4.1 SPI Clock Formats ........................................................................................................210
12.4.2 SPI Interrupts ................................................................................................................213
12.4.3 Mode Fault Detection ...................................................................................................213
Chapter 13
Inter-Integrated Circuit (S08IICV1)
13.1 Introduction ...................................................................................................................................215
13.1.1 Features .........................................................................................................................217
13.1.2 Modes of Operation ......................................................................................................217
13.1.3 Block Diagram ..............................................................................................................218
13.2 External Signal Description ..........................................................................................................218
13.2.1 SCL — Serial Clock Line .............................................................................................218
13.2.2 SDA — Serial Data Line ..............................................................................................218
13.3 Register Definition ........................................................................................................................218
13.3.1 IIC Address Register (IIC1A) .......................................................................................219
13.3.2 IIC Frequency Divider Register (IIC1F) ......................................................................219
13.3.3 IIC Control Register (IIC1C) ........................................................................................222
13.3.4 IIC Status Register (IIC1S) ..........................................................................................223
13.3.5 IIC Data I/O Register (IIC1D) ......................................................................................224
13.4 Functional Description ..................................................................................................................225
13.4.1 IIC Protocol ..................................................................................................................225
13.5 Resets ............................................................................................................................................228
13.6 Interrupts .......................................................................................................................................228
13.6.1 Byte Transfer Interrupt .................................................................................................229
13.6.2 Address Detect Interrupt ...............................................................................................229
13.6.3 Arbitration Lost Interrupt .............................................................................................229
13.7 Initialization/Application Information ..........................................................................................230
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
15
Section Number
Title
Page
Chapter 14
Analog-to-Digital Converter (S08ADC10V1)
14.1 Overview .......................................................................................................................................233
14.2 Channel Assignments ....................................................................................................................233
14.2.1 Alternate Clock .............................................................................................................234
14.2.2 Hardware Trigger ..........................................................................................................234
14.2.3 Temperature Sensor ......................................................................................................235
14.2.4 Features .........................................................................................................................237
14.2.5 Block Diagram ..............................................................................................................237
14.3 External Signal Description ..........................................................................................................238
14.3.1 Analog Power (V
) ................................................................................................239
DDAD
14.3.2 Analog Ground (V
) ..............................................................................................239
SSAD
14.3.3 Voltage Reference High (V
) .................................................................................239
REFH
14.3.4 Voltage Reference Low (V
) ..................................................................................239
REFL
14.3.5 Analog Channel Inputs (ADx) ......................................................................................239
14.4 Register Definition ........................................................................................................................239
14.4.1 Status and Control Register 1 (ADC1SC1) ..................................................................239
14.4.2 Status and Control Register 2 (ADC1SC2) ..................................................................241
14.4.3 Data Result High Register (ADC1RH) ........................................................................242
14.4.4 Data Result Low Register (ADC1RL) ..........................................................................242
14.4.5 Compare Value High Register (ADC1CVH) ................................................................243
14.4.6 Compare Value Low Register (ADC1CVL) .................................................................243
14.4.7 Configuration Register (ADC1CFG) ............................................................................243
14.4.8 Pin Control 1 Register (APCTL1) ................................................................................245
14.4.9 Pin Control 2 Register (APCTL2) ................................................................................246
14.4.10 Pin Control 3 Register (APCTL3) ................................................................................247
14.5 Functional Description ..................................................................................................................248
14.5.1 Clock Select and Divide Control ..................................................................................248
14.5.2 Input Select and Pin Control .........................................................................................249
14.5.3 Hardware Trigger ..........................................................................................................249
14.5.4 Conversion Control .......................................................................................................249
14.5.5 Automatic Compare Function ......................................................................................252
14.5.6 MCU Wait Mode Operation .........................................................................................252
14.5.7 MCU Stop3 Mode Operation .......................................................................................252
14.5.8 MCU Stop1 and Stop2 Mode Operation ......................................................................253
14.6 Initialization Information ..............................................................................................................253
14.6.1 ADC Module Initialization Example ...........................................................................253
14.7 Application Information ................................................................................................................255
14.7.1 External Pins and Routing ............................................................................................255
14.7.2 Sources of Error ............................................................................................................257
MC9S08AW60 Data Sheet, Rev 2
16
Freescale Semiconductor
Section Number
Title
Page
Chapter 15
Development Support
15.1 Introduction ...................................................................................................................................261
15.1.1 Features .........................................................................................................................262
15.2 Background Debug Controller (BDC) ..........................................................................................262
15.2.1 BKGD Pin Description .................................................................................................263
15.2.2 Communication Details ................................................................................................264
15.2.3 BDC Commands ...........................................................................................................268
15.2.4 BDC Hardware Breakpoint ..........................................................................................270
15.3 On-Chip Debug System (DBG) ....................................................................................................271
15.3.1 Comparators A and B ...................................................................................................271
15.3.2 Bus Capture Information and FIFO Operation .............................................................271
15.3.3 Change-of-Flow Information ........................................................................................272
15.3.4 Tag vs. Force Breakpoints and Triggers .......................................................................272
15.3.5 Trigger Modes ..............................................................................................................273
15.3.6 Hardware Breakpoints ..................................................................................................275
15.4 Register Definition ........................................................................................................................275
15.4.1 BDC Registers and Control Bits ...................................................................................275
15.4.2 System Background Debug Force Reset Register (SBDFR) ........................................277
15.4.3 DBG Registers and Control Bits ..................................................................................278
Appendix A
Electrical Characteristics and Timing Specifications
A.1 Introduction ....................................................................................................................................283
A.2 Parameter Classification.................................................................................................................283
A.3 Absolute Maximum Ratings...........................................................................................................283
A.4 Thermal Characteristics..................................................................................................................285
A.5 ESD Protection and Latch-Up Immunity.......................................................................................286
A.6 DC Characteristics..........................................................................................................................287
A.7 Supply Current Characteristics.......................................................................................................291
A.8 ADC Characteristics.......................................................................................................................293
A.9 Internal Clock Generation Module Characteristics........................................................................296
A.9.1 ICG Frequency Specifications.......................................................................................297
A.10 AC Characteristics..........................................................................................................................300
A.10.1 Control Timing..............................................................................................................300
A.10.2 Timer/PWM (TPM) Module Timing.............................................................................302
A.11 SPI Characteristics .........................................................................................................................303
A.12 FLASH Specifications....................................................................................................................306
A.13 EMC Performance..........................................................................................................................307
A.13.1 Radiated Emissions .......................................................................................................307
A.13.2 Conducted Transient Susceptibility...............................................................................307
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
17
Section Number
Title
Page
Appendix B
Ordering Information and Mechanical Drawings
B.1 Ordering Information .....................................................................................................................309
B.2 Orderable Part Numbering System ................................................................................................310
B.2.1 Consumer and Industrial Orderable Part Numbering System .......................................310
B.2.2 Automotive Orderable Part Numbering System............................................................310
B.3 Mechanical Drawings.....................................................................................................................310
MC9S08AW60 Data Sheet, Rev 2
18
Freescale Semiconductor
Chapter 1
Introduction
1.1
Overview
The MC9S08AW60, MC9S08AW48, MC9S08AW32, and MC9S08AW16 are members of the low-cost,
high-performance HCS08 family of 8-bit microcontroller units (MCUs). All MCUs in the family use the
enhanced HCS08 core and are available with a variety of modules, memory sizes, memory types, and
package types. Refer to Table 1-1 for memory sizes and package types.
Table 1-2 summarizes the peripheral availability per package type for the devices available in the
MC9S08AW60 Series.
Table 1-1. Devices in the MC9S08AW60 Series
Device
FLASH
RAM
Package
MC9S08AW60
MC9S08AW48
63,280
49,152
32,768
64 QFP
64 LQFP
48 QFN
44 LQFP
2048
MC9S08AW32
MC9S08AW16
48 QFN
44 LQFP
16,384
1024
Table 1-2. Peripherals Available per Package Type
Package Options
Feature
64-pin
48-pin
44-pin
ADC
IIC
16-channel
8-channel
8-channel
yes
yes
yes
yes
yes
yes
IRQ
KBI1
8
7
6
SCI1
yes
yes
yes
SCI2
yes
yes
yes
SPI1
yes
yes
yes
TPM1
TPM1CLK
TPM2
TPM2CLK
I/O pins
6-channel
yes
4-channel
no
4-channel
no
2-channel
yes
2-channel
no
2-channel
no
54
38
34
1.2
MCU Block Diagrams
The block diagram shows the structure of the MC9S08AW60 Series.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
19
Chapter 1 Introduction
HCS08 CORE
DEBUG
MODULE (DBG)
8
PTA7– PTA0
BKGD/MS
BDC
CPU
8
PTB7/AD1P7–
PTB0/AD1P0
HCS08 SYSTEM CONTROL
RESET
IRQ
PTC6
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
RxD2
TxD2
PTC5/RxD2
PTC4
PTC3/TxD2
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI2)
PTC2/MCLK
PTC1/SDA1
SDA1
SCL1
RTI
COP
LVD
IIC MODULE (IIC1)
PTC0/SCL1
IRQ
AD1P7–AD1P0
8
V
DDAD
8
10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC1)
AD1P15–AD1P8
V
SSAD
V
REFL
PTD7/AD1P15/KBI1P7
PTD6/AD1P14/TPM1CLK
PTD5/AD1P13
PTD4/AD1P12/TPM2CLK
PTD3/AD1P11/KBI1P6
PTD2/AD1P10/KBI1P5
PTD1/AD1P9
V
REFH
USER FLASH
(AW60 = 63,280 BYTES)
(AW48 = 49,152 BYTES)
(AW32 = 32,768 BYTES)
(AW16 = 16,384 BYTES)
PTD0/AD1P8
SPSCK1
PTE7/SPSCK1
PTE6/MOSI1
MOSI1
SERIAL PERIPHERAL
USER RAM
MISO1
SS1
INTERFACE MODULE (SPI1)
PTE5/MISO1
PTE4/SS1
AW60/48/32 = 2048 BYTES
AW16 = 1024 BYTES
TPM1CLK
PTE3/TPM1CH1
PTE2/TPM1CH0
6-CHANNEL TIMER/PWM
MODULE (TPM1)
TPM1CH5–
TPM1CH0
INTERNAL CLOCK
GENERATOR (ICG)
6
RxD1
TxD1
PTE1/RxD1
PTE0/TxD1
PTF7
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI1)
LOW-POWER OSCILLATOR
PTF6
PTF5/TPM2CH1
PTF4/TPM2CH0
TPM2CLK
V
DD
VOLTAGE
REGULATOR
2-CHANNEL TIMER/PWM
MODULE (TPM2)
TPM2CH1–TPM2CH0
V
SS
2
PTF3/TPM1CH5
KBI1P7–KBI1P5
3
PTF2/TPM1CH4
PTF1/TPM1CH3
PTF0/TPM1CH2
8-BIT KEYBOARD
INTERRUPT MODULE (KBI1)
KBI1P4–KBI1P0
5
EXTAL
XTAL
PTG6/EXTAL
PTG5/XTAL
NOTES:
PTG4/KBI1P4
PTG3/KBI1P3
PTG2/KBI1P2
PTG1/KBI1P1
PTG0/KBI1P0
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software-configurable pullup/pulldown device if IRQ is enabled
(IRQPE = 1). Pulldown is enabled if rising edge detect is selected (IRQEDG = 1)
3. IRQ does not have a clamp diode to VDD. IRQ should not be driven above VDD
4. Pin contains integrated pullup device.
.
5. Pins PTD7, PTD3, PTD2, and PTG4 contain both pullup and pulldown devices.
Pulldown enabled when KBI is enabled (KBIPEn = 1) and rising edge is selected
(KBEDGn = 1).
Figure 1-1. MC9S08AW60 Series Block Diagram
MC9S08AW60 Data Sheet, Rev 2
20
Freescale Semiconductor
Chapter 1 Introduction
Table 1-3 lists the functional versions of the on-chip modules.
Table 1-3. Versions of On-Chip Modules
Module
Version
Analog-to-Digital Converter
Internal Clock Generator
Inter-Integrated Circuit
Keyboard Interrupt
(S08ADC10)
(S08ICG)
(S08IIC)
1
4
1
1
2
3
2
2
2
(S08KBI)
(S08SCI)
(S08SPI)
(S08TPM)
(S08CPU)
(DBG)
Serial Communications Interface
Serial Peripheral Interface
Timer Pulse-Width Modulator
Central Processing Unit
Debug Module
1.3
System Clock Distribution
SYSTEM
CONTROL
LOGIC
TPM1
TPM2
IIC1
SCI1
SCI2
SPI1
ICGERCLK
FFE
RTI
÷2
ICG
FIXED FREQ CLOCK (XCLK)
BUSCLK
ICGOUT
÷2
ICGLCLK*
CPU
BDC
RAM
FLASH
ADC1
ADC has min and max
frequency requirements.
See Chapter 14,
FLASH has frequency
requirements for program
and erase operation.
* ICGLCLK is the alternate BDC clock source for the MC9S08AW60 Series.
“Analog-to-Digital Converter
(S08ADC10V1) and
See Appendix A, “Electrical
Characteristics and Timing
Specifications.
Appendix A, “Electrical
Characteristics and Timing
Specifications
Figure 1-2. System Clock Distribution Diagram
Some of the modules inside the MCU have clock source choices. Figure 1-2 shows a simplified clock
connection diagram. The ICG supplies the clock sources:
•
ICGOUT is an output of the ICG module. It is one of the following:
— The external crystal oscillator
— An external clock source
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
21
Chapter 1 Introduction
— The output of the digitally-controlled oscillator (DCO) in the frequency-locked loop
sub-module
— Control bits inside the ICG determine which source is connected.
•
FFE is a control signal generated inside the ICG. If the frequency of ICGOUT > 4 × the frequency
of ICGERCLK, this signal is a logic 1 and the fixed-frequency clock will be ICGERCLK/2.
Otherwise the fixed-frequency clock will be BUSCLK.
•
•
ICGLCLK — Development tools can select this internal self-clocked source (~ 8 MHz) to speed
up BDC communications in systems where the bus clock is slow.
ICGERCLK — External reference clock can be selected as the real-time interrupt clock source.
Can also be used as the ALTCLK input to the ADC module.
MC9S08AW60 Data Sheet, Rev 2
22
Freescale Semiconductor
Chapter 2
Pins and Connections
2.1
Introduction
This chapter describes signals that connect to package pins. It includes a pinout diagram, a table of signal
properties, and detailed discussion of signals.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
23
Chapter 2 Pins and Connections
2.2
Device Pin Assignment
64
49
63 62 61 60 59 58 57 56 55 54 53 52 51 50
PTC4
PTG3/KBI1P3
48
1
PTD3/KBI1P6/AD1P11
47
46
45
IRQ
RESET
2
3
4
5
6
7
8
9
PTD2/KBI1P5/AD1P10
PTF0/TPM1CH2
PTF1/TPM1CH3
PTF2/TPM1CH4
PTF3/TPM1CH5
PTF4/TPM2CH0
PTC6
V
SSAD
44
43
42
41
40
39
38
37
V
DDAD
PTD1/AD1P9
PTD0/AD1P8
PTB7/AD1P7
PTB6/AD1P6
PTB5/AD1P5
64-Pin QFP
64-Pin LQFP
PTF7
10
11
12
13
14
15
PTF5/TPM2CH1
PTB4/AD1P4
PTB3/AD1P3
PTB2/AD1P2
PTF6
PTE0/TxD1
36
35
34
PTE1/RxD1
PTB1/AD1P1
PTB0/AD1P0
PTA7
PTE2/TPM1CH0
PTE3/TPM1CH1
16
33
23 24 25 26 27 28 29 30 31
18 19 20 21 22
32
17
Figure 2-1. MC9S08AW60 Series in 64-Pin QFP/LQFP Package
MC9S08AW60 Data Sheet, Rev 2
24
Freescale Semiconductor
Chapter 2 Pins and Connections
36 PTG3/KBI1P3
1
PTC4
IRQ
35 PTD3/KBI1P6/AD1P11
34 PTD2/KBI1P5/AD1P10
2
3
RESET
33
32
V
V
4
PTF0/TPM1CH2
PTF1/TPM1CH3
PTF4/TPM2CH0
PTF5/TPM2CH1
PTF6
SSAD
DDAD
5
6
31 PTD1/AD1P9
30 PTD0/AD1P8
29 PTB3/AD1P3
28 PTB2/AD1P2
48-Pin QFN
7
8
9
PTE0/TxD1
10
11
12
PTE1/RxD1
27
PTB1/AD1P1
PTE2/TPM1CH0
PTE3/TPM1CH1
26 PTB0/AD1P0
25 PTA7
Figure 2-2. MC9S08AW60 Series in 48-Pin QFN Package
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
25
Chapter 2 Pins and Connections
34
44
43 42 41 40 39 38 37 36 35
PTC4
1
PTG3/KBI1P3
33
IRQ
RESET
2
3
4
5
6
7
8
9
32
31
30
29
PTD3/KBI1P6/AD1P11
PTD2/KBI1P5/AD1P10
PTF0/TPM1CH2
PTF1/TPM1CH3
PTF4/TPM2CH0
V
SSAD
V
DDAD
44-Pin LQFP
28
27
26
PTD1/AD1P9
PTD0/AD1P8
PTB3/AD1P3
PTB2/AD1P2
PTF5/TPM2CH1
PTE0/TxD1
PTE1/RxD1
25
24
PTE2/TPM1CH0
PTE3/TPM1CH1
10
PTB1/AD1P1
PTB0/AD1P0
11
23
18 19 20 21
13 14 15 16 17
22
12
Figure 2-3. MC9S08AW60 Series in 44-Pin LQFP Package
2.3
Recommended System Connections
Figure 2-4 shows pin connections that are common to almost all MC9S08AW60 Series application
systems.
MC9S08AW60 Data Sheet, Rev 2
26
Freescale Semiconductor
Chapter 2 Pins and Connections
V
V
REFH
MC9S08AW60
DDAD
C
BYAD
PTA0
PTA1
PTA2
PTA3
PTA4
PTA5
PTA6
PTA7
0.1 μF
V
V
SSAD
V
+
DD
SYSTEM
POWER
REFL
V
DD
PORT
A
+
C
C
BY
BLK
5 V
0.1 μF
10 μF
V
(x2)
SS
NOTE 1
R
F
PTB0/AD1P0
PTB1/AD1P1
PTB2/AD1P2
PTB3/AD1P3
PTB4/AD1P4
PTB5/AD1P5
R
S
XTAL
NOTE 2
C2
C1
X1
EXTAL
NOTE 2
PORT
B
BACKGROUND HEADER
I/O AND
PERIPHERAL
INTERFACE TO
APPLICATION
SYSTEM
PTB6/AD1P6
PTB7/AD1P7
1
V
DD
BKGD/MS
PTC0/SCL1
PTC1/SDA1
PTC2/MCLK
PTC3/TxD2
PTC4
V
DD
4.7 kΩ–10 kΩ
PORT
C
RESET
NOTE 3
0.1 μF V
DD
PTC5/RxD2
PTC6
OPTIONAL
MANUAL
RESET
4.7 kΩ–
10 kΩ
ASYNCHRONOUS
INTERRUPT
IRQ
INPUT
0.1 μF
NOTE 3
PTD0/AD1P8
PTD1/AD1P9
PTG0/KBI1P0
PTD2/AD1P10/KBI1P5
PTD3/AD1P11/KBI1P6
PTD4/AD1P12/TPM2CLK
PTD5/AD1P13
PTG1/KBI1P1
PTG2/KBI1P2
PTG3/KBI1P3
PORT
PORT
D
G
PTG4/KBI1P4
PTG5/XTAL
PTD6/AD1P14/TPM1CLK
PTD7/AD1P15/KBI1P7
PTG6/EXTAL
NOTES:
1. Not required if
using the internal
clock option.
2. These are the
same pins as
PTG5 and PTG6
3. RC filters on
RESET and IRQ
are recommended
for EMC-sensitive
applications.
PTE0/TxD1
PTF0/TPM1CH2
PTF1/TPM1CH3
PTF2/TPM1CH4
PTF3/TPM1CH5
PTF4/TPM2CH0
PTE1/RxD1
PTE2/TPM1CH0
PTE3/TPM1CH1
PTE4/SS1
PORT
E
PORT
F
PTE5/MISO1
PTE6/MOSI1
PTE7/SPSCK1
PTF5/TPM2CH1
PTF6
PTF7
Figure 2-4. Basic System Connections
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
27
Chapter 2 Pins and Connections
2.3.1
Power (VDD, 2 x VSS, VDDAD, VSSAD)
V
and V are the primary power supply pins for the MCU. This voltage source supplies power to all
SS
DD
I/O buffer circuitry and to an internal voltage regulator. The internal voltage regulator provides regulated
lower-voltage source to the CPU and other internal circuitry of the MCU.
Typically, application systems have two separate capacitors across the power pins. In this case, there
should be a bulk electrolytic capacitor, such as a 10-μF tantalum capacitor, to provide bulk charge storage
for the overall system and a 0.1-μF ceramic bypass capacitor located as near to the paired V and V
DD
SS
power pins as practical to suppress high-frequency noise. The MC9S08AW60 has a second V pin. This
SS
pin should be connected to the system ground plane or to the primary V pin through a low-impedance
SS
connection.
V
and V
are the analog power supply pins for the MCU. This voltage source supplies power to
SSAD
DDAD
the ADC module. A 0.1-μF ceramic bypass capacitor should be located as near to the analog power pins
as practical to suppress high-frequency noise.
2.3.2
Oscillator (XTAL, EXTAL)
Out of reset, the MCU uses an internally generated clock (self-clocked mode — f
) equivalent to
Self_reset
about 8-MHz crystal rate. This frequency source is used during reset startup and can be enabled as the
clock source for stop recovery to avoid the need for a long crystal startup delay. This MCU also contains
a trimmable internal clock generator (ICG) module that can be used to run the MCU. For more information
on the ICG, see the Chapter 8, “Internal Clock Generator (S08ICGV4).”
The oscillator amplitude on XTAL and EXTAL is gain limited for low-power oscillation. Typically, these
pins have a 1-V peak-to-peak signal. For noisy environments, the high gain output (HGO) bit can be set to
enable rail-to-rail oscillation.
The oscillator in this MCU is a Pierce oscillator that can accommodate a crystal or ceramic resonator in
either of two frequency ranges selected by the RANGE bit in the ICGC1 register. Rather than a crystal or
ceramic resonator, an external oscillator can be connected to the EXTAL input pin.
Refer to Figure 2-4 for the following discussion. R (when used) and R should be low-inductance
S
F
resistors such as carbon composition resistors. Wire-wound resistors, and some metal film resistors, have
too much inductance. C1 and C2 normally should be high-quality ceramic capacitors that are specifically
designed for high-frequency applications.
R is used to provide a bias path to keep the EXTAL input in its linear range during crystal startup and its
F
value is not generally critical. Typical systems use 1 MΩ to 10 MΩ. Higher values are sensitive to humidity
and lower values reduce gain and (in extreme cases) could prevent startup.
C1 and C2 are typically in the 5-pF to 25-pF range and are chosen to match the requirements of a specific
crystal or resonator. Be sure to take into account printed circuit board (PCB) capacitance and MCU pin
capacitance when sizing C1 and C2. The crystal manufacturer typically specifies a load capacitance which
is the series combination of C1 and C2 which are usually the same size. As a first-order approximation,
use 10 pF as an estimate of combined pin and PCB capacitance for each oscillator pin (EXTAL and
XTAL).
MC9S08AW60 Data Sheet, Rev 2
28
Freescale Semiconductor
Chapter 2 Pins and Connections
2.3.3
RESET Pin
RESET is a dedicated pin with a pullup device built in. It has input hysteresis, a high current output driver,
and no output slew rate control. Internal power-on reset and low-voltage reset circuitry typically make
external reset circuitry unnecessary. This pin is normally connected to the standard 6-pin background
debug connector so a development system can directly reset the MCU system. If desired, a manual external
reset can be added by supplying a simple switch to ground (pull reset pin low to force a reset).
Whenever any reset is initiated (whether from an external signal or from an internal system), the reset pin
is driven low for approximately 34 bus cycles, released, and sampled again approximately 38 bus cycles
later. If reset was caused by an internal source such as low-voltage reset or watchdog timeout, the circuitry
expects the reset pin sample to return a logic 1. The reset circuitry decodes the cause of reset and records
it by setting a corresponding bit in the system control reset status register (SRS).
In EMC-sensitive applications, an external RC filter is recommended on the reset pin. See Figure 2-4 for
an example.
2.3.4
Background/Mode Select (BKGD/MS)
While in reset, the BKGD/MS pin functions as a mode select pin. Immediately after reset rises the pin
functions as the background pin and can be used for background debug communication. While functioning
as a background/mode select pin, the pin includes an internal pullup device, input hysteresis, a standard
output driver, and no output slew rate control.
If nothing is connected to this pin, the MCU will enter normal operating mode at the rising edge of reset.
If a debug system is connected to the 6-pin standard background debug header, it can hold BKGD/MS low
during the rising edge of reset which forces the MCU to active background mode.
The BKGD pin is used primarily for background debug controller (BDC) communications using a custom
protocol that uses 16 clock cycles of the target MCU’s BDC clock per bit time. The target MCU’s BDC
clock could be as fast as the bus clock rate, so there should never be any significant capacitance connected
to the BKGD/MS pin that could interfere with background serial communications.
Although the BKGD pin is a pseudo open-drain pin, the background debug communication protocol
provides brief, actively driven, high speedup pulses to ensure fast rise times. Small capacitances from
cables and the absolute value of the internal pullup device play almost no role in determining rise and fall
times on the BKGD pin.
2.3.5
ADC Reference Pins (VREFH, VREFL)
The V
and V
pins are the voltage reference high and voltage reference low inputs respectively
REFH
REFL
for the ADC module.
2.3.6
External Interrupt Pin (IRQ)
The IRQ pin is the input source for the IRQ interrupt and is also the input for the BIH and BIL instructions.
If the IRQ function is not enabled, this pin does not perform any function.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
29
Chapter 2 Pins and Connections
When IRQ is configured as the IRQ input and is set to detect rising edges, a pulldown device rather than
a pullup device is enabled.
In EMC-sensitive applications, an external RC filter is recommended on the IRQ pin. See Figure 2-4 for
an example.
2.3.7
General-Purpose I/O and Peripheral Ports
The remaining pins are shared among general-purpose I/O and on-chip peripheral functions such as timers
and serial I/O systems. Immediately after reset, all of these pins are configured as high-impedance
general-purpose inputs with internal pullup devices disabled.
NOTE
To avoid extra current drain from floating input pins, the reset initialization
routine in the application program should either enable on-chip pullup
devices or change the direction of unused pins to outputs so the pins do not
float.
For information about controlling these pins as general-purpose I/O pins, see Chapter 6, “Parallel
Input/Output.” For information about how and when on-chip peripheral systems use these pins, refer to the
appropriate chapter from Table 2-1.
Table 2-1. Pin Sharing Priority
Lowest <- Pin Function Priority -> Highest
Reference1
Port Pins
Alternate Function
Alternate Function
PTB7–PTB0
PTC5, PTC3
PTC2
AD1P7–AD1P0
RxD2–TxD2
MCLK
Chapter 14, “Analog-to-Digital Converter (S08ADC10V1)”
Chapter 11, “Serial Communications Interface (S08SCIV2)”
Chapter 5, “Resets, Interrupts, and System Configuration”
Chapter 13, “Inter-Integrated Circuit (S08IICV1)”
PTC1–PTC0
PTD7
SCL1–SDA1
KBI1P7
AD1P15
AD1P14
Chapter 14, “Analog-to-Digital Converter (S08ADC10V1)”
Chapter 9, “Keyboard Interrupt (S08KBIV1)”
PTD6
TPM1CLK
Chapter 14, “Analog-to-Digital Converter (S08ADC10V1)”
Chapter 10, “Timer/PWM (S08TPMV2)”
PTD5
PTD4
AD1P13
AD1P13
AD1P12
Chapter 14, “Analog-to-Digital Converter (S08ADC10V1)”
TPM2CLK
Chapter 14, “Analog-to-Digital Converter (S08ADC10V1)”
Chapter 10, “Timer/PWM (S08TPMV2)”
PTD3–PTD2
PTD1–PTD0
KBI1P6–KBI1P5
AD1P11–AD1P10
Chapter 14, “Analog-to-Digital Converter (S08ADC10V1)”
Chapter 9, “Keyboard Interrupt (S08KBIV1)”
AD1P9–AD1P8
Chapter 14, “Analog-to-Digital Converter (S08ADC10V1)”
Chapter 12, “Serial Peripheral Interface (S08SPIV3)”
PTE7
PTE6
PTE5
PTE4
SPSCK1
MOSI1
MISO1
SS1
PTE3–PTE2
TPM1CH1–
TPM1CH0
Chapter 10, “Timer/PWM (S08TPMV2)”
PTE1–PTE0
PTF5–PTF4
RxD1–TxD1
Chapter 11, “Serial Communications Interface (S08SCIV2)”
Chapter 10, “Timer/PWM (S08TPMV2)”
TPM2CH1–
TPM2CH0
MC9S08AW60 Data Sheet, Rev 2
30
Freescale Semiconductor
Chapter 2 Pins and Connections
Table 2-1. Pin Sharing Priority
Lowest <- Pin Function Priority -> Highest
Reference1
Port Pins
Alternate Function
Alternate Function
PTF3–PTF0
TPM1CH5–
TPM1CH2
Chapter 10, “Timer/PWM (S08TPMV2)”
PTG4–PTG0
PTG6–PTG5
KBI1P4–KBI1P0
EXTAL–XTAL
Chapter 9, “Keyboard Interrupt (S08KBIV1)”
Chapter 8, “Internal Clock Generator (S08ICGV4)”
1
See the listed chapter for information about modules that share these pins.
When an on-chip peripheral system is controlling a pin, data direction control bits still determine what is
read from port data registers even though the peripheral module controls the pin direction by controlling
the enable for the pin’s output buffer. See the Chapter 6, “Parallel Input/Output” chapter for more details.
Pullup enable bits for each input pin control whether on-chip pullup devices are enabled whenever the pin
is acting as an input even if it is being controlled by an on-chip peripheral module. When the PTD7, PTD3,
PTD2, and PTG4 pins are controlled by the KBI module and are configured for rising-edge/high-level
sensitivity, the pullup enable control bits enable pulldown devices rather than pullup devices.
NOTE
When an alternative function is first enabled it is possible to get a spurious
edge to the module, user software should clear out any associated flags
before interrupts are enabled. Table 2-1 illustrates the priority if multiple
modules are enabled. The highest priority module will have control over the
pin. Selecting a higher priority pin function with a lower priority function
already enabled can cause spurious edges to the lower priority module. It is
recommended that all modules that share a pin be disabled before enabling
another module.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
31
Chapter 2 Pins and Connections
MC9S08AW60 Data Sheet, Rev 2
32
Freescale Semiconductor
Chapter 3
Modes of Operation
3.1
Introduction
The operating modes of the MC9S08AW60 Series are described in this chapter. Entry into each mode, exit
from each mode, and functionality while in each of the modes are described.
3.2
Features
•
Active background mode for code development
•
Wait mode:
— CPU shuts down to conserve power
— System clocks running
— Full voltage regulation maintained
Stop modes:
•
— System clocks stopped; voltage regulator in standby
— Stop2 — Partial power down of internal circuits, RAM contents retained
— Stop3 — All internal circuits powered for fast recovery
3.3
Run Mode
This is the normal operating mode for the MC9S08AW60 Series. This mode is selected when the
BKGD/MS pin is high at the rising edge of reset. In this mode, the CPU executes code from internal
memory with execution beginning at the address fetched from memory at $FFFE:$FFFF after reset.
3.4
Active Background Mode
The active background mode functions are managed through the background debug controller (BDC) in
the HCS08 core. The BDC, together with the on-chip debug module (DBG), provide the means for
analyzing MCU operation during software development.
Active background mode is entered in any of five ways:
•
•
•
•
•
When the BKGD/MS pin is low at the rising edge of reset
When a BACKGROUND command is received through the BKGD pin
When a BGND instruction is executed
When encountering a BDC breakpoint
When encountering a DBG breakpoint
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
33
Chapter 3 Modes of Operation
After entering active background mode, the CPU is held in a suspended state waiting for serial background
commands rather than executing instructions from the user’s application program.
Background commands are of two types:
•
Non-intrusive commands, defined as commands that can be issued while the user program is
running. Non-intrusive commands can be issued through the BKGD pin while the MCU is in run
mode; non-intrusive commands can also be executed when the MCU is in the active background
mode. Non-intrusive commands include:
— Memory access commands
— Memory-access-with-status commands
— BDC register access commands
— The BACKGROUND command
•
Active background commands, which can only be executed while the MCU is in active background
mode. Active background commands include commands to:
— Read or write CPU registers
— Trace one user program instruction at a time
— Leave active background mode to return to the user’s application program (GO)
The active background mode is used to program a bootloader or user application program into the FLASH
program memory before the MCU is operated in run mode for the first time. When the MC9S08AW60
Series is shipped from the Freescale Semiconductor factory, the FLASH program memory is erased by
default unless specifically noted so there is no program that could be executed in run mode until the
FLASH memory is initially programmed. The active background mode can also be used to erase and
reprogram the FLASH memory after it has been previously programmed.
For additional information about the active background mode, refer to Chapter 15, “Development
Support.”
3.5
Wait Mode
Wait mode is entered by executing a WAIT instruction. Upon execution of the WAIT instruction, the CPU
enters a low-power state in which it is not clocked. The I bit in CCR is cleared when the CPU enters the
wait mode, enabling interrupts. When an interrupt request occurs, the CPU exits the wait mode and
resumes processing, beginning with the stacking operations leading to the interrupt service routine.
While the MCU is in wait mode, there are some restrictions on which background debug commands can
be used. Only the BACKGROUND command and memory-access-with-status commands are available
when the MCU is in wait mode. The memory-access-with-status commands do not allow memory access,
but they report an error indicating that the MCU is in either stop or wait mode. The BACKGROUND
command can be used to wake the MCU from wait mode and enter active background mode.
3.6
Stop Modes
One of two stop modes is entered upon execution of a STOP instruction when the STOPE bit in the system
option register is set. In both stop modes, all internal clocks are halted. If the STOPE bit is not set when
MC9S08AW60 Data Sheet, Rev 2
34
Freescale Semiconductor
Chapter 3 Modes of Operation
the CPU executes a STOP instruction, the MCU will not enter either of the stop modes and an illegal
opcode reset is forced. The stop modes are selected by setting the appropriate bits in SPMSC2.
HCS08 devices that are designed for low voltage operation (1.8V to 3.6V) also include stop1 mode. The
MC9S08AW60 Series family of devices does not include stop1 mode.
Table 3-1 summarizes the behavior of the MCU in each of the stop modes.
Table 3-1. Stop Mode Behavior
CPU, Digital
Mode
PPDC Peripherals,
FLASH
RAM
ICG
ADC1
Regulator
I/O Pins
RTI
Stop2
Stop3
1
0
Off
Standby
Standby
Off
Disabled
Standby
Standby
States
held
Optionally on
Optionally on
Standby
Off1
Optionally on
States
held
1
Crystal oscillator can be configured to run in stop3. Please see the ICG registers.
3.6.1
Stop2 Mode
The stop2 mode provides very low standby power consumption and maintains the contents of RAM and
the current state of all of the I/O pins. To enter stop2, the user must execute a STOP instruction with stop2
selected (PPDC = 1) and stop mode enabled (STOPE = 1). In addition, the LVD must not be enabled to
operate in stop (LVDSE = 0 or LVDE = 0). If the LVD is enabled in stop, then the MCU enters stop3 upon
the execution of the STOP instruction regardless of the state of PPDC.
Before entering stop2 mode, the user must save the contents of the I/O port registers, as well as any other
memory-mapped registers which they want to restore after exit of stop2, to locations in RAM. Upon exit
of stop2, these values can be restored by user software before pin latches are opened.
When the MCU is in stop2 mode, all internal circuits that are powered from the voltage regulator are turned
off, except for the RAM. The voltage regulator is in a low-power standby state, as is the ADC. Upon entry
into stop2, the states of the I/O pins are latched. The states are held while in stop2 mode and after exiting
stop2 mode until a logic 1 is written to PPDACK in SPMSC2.
Exit from stop2 is done by asserting either of the wake-up pins: RESET or IRQ, or by an RTI interrupt.
IRQ is always an active low input when the MCU is in stop2, regardless of how it was configured before
entering stop2.
NOTE
Although this IRQ pin is automatically configured as active low input, the
pullup associated with the IRQ pin is not automatically enabled. Therefore,
if an external pullup is not used, the internal pullup must be enabled by
setting IRQPE in IRQSC.
Upon wake-up from stop2 mode, the MCU will start up as from a power-on reset (POR) except pin states
remain latched. The CPU will take the reset vector. The system and all peripherals will be in their default
reset states and must be initialized.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
35
Chapter 3 Modes of Operation
After waking up from stop2, the PPDF bit in SPMSC2 is set. This flag may be used to direct user code to
go to a stop2 recovery routine. PPDF remains set and the I/O pin states remain latched until a logic 1 is
written to PPDACK in SPMSC2.
To maintain I/O state for pins that were configured as general-purpose I/O, the user must restore the
contents of the I/O port registers, which have been saved in RAM, to the port registers before writing to
the PPDACK bit. If the port registers are not restored from RAM before writing to PPDACK, then the
register bits will assume their reset states when the I/O pin latches are opened and the I/O pins will switch
to their reset states.
For pins that were configured as peripheral I/O, the user must reconfigure the peripheral module that
interfaces to the pin before writing to the PPDACK bit. If the peripheral module is not enabled before
writing to PPDACK, the pins will be controlled by their associated port control registers when the I/O
latches are opened.
3.6.2
Stop3 Mode
Stop3 mode is entered by executing a STOP instruction under the conditions as shown in Table 3-1. The
states of all of the internal registers and logic, RAM contents, and I/O pin states are maintained.
Stop3 can be exited by asserting RESET, or by an interrupt from one of the following sources: the real-time
interrupt (RTI), LVD, ADC, IRQ, or the KBI.
If stop3 is exited by means of the RESET pin, then the MCU is reset and operation will resume after taking
the reset vector. Exit by means of one of the internal interrupt sources results in the MCU taking the
appropriate interrupt vector.
3.6.3
Active BDM Enabled in Stop Mode
Entry into the active background mode from run mode is enabled if the ENBDM bit in BDCSCR is set.
This register is described in Chapter 15, “Development Support” of this data sheet. If ENBDM is set when
the CPU executes a STOP instruction, the system clocks to the background debug logic remain active when
the MCU enters stop mode so background debug communication is still possible. In addition, the voltage
regulator does not enter its low-power standby state but maintains full internal regulation. If the user
attempts to enter stop2 with ENBDM set, the MCU will instead enter stop3.
Most background commands are not available in stop mode. The memory-access-with-status commands
do not allow memory access, but they report an error indicating that the MCU is in either stop or wait
mode. The BACKGROUND command can be used to wake the MCU from stop and enter active
background mode if the ENBDM bit is set. After entering background debug mode, all background
commands are available. Table 3-2 summarizes the behavior of the MCU in stop when entry into the
background debug mode is enabled.
MC9S08AW60 Data Sheet, Rev 2
36
Freescale Semiconductor
Chapter 3 Modes of Operation
Table 3-2. BDM Enabled Stop Mode Behavior
CPU, Digital
Mode
PPDC Peripherals,
FLASH
RAM
ICG
ADC1
Regulator
I/O Pins
RTI
Stop3
0
Standby
Standby
Active Optionally on
Active
States
held
Optionally on
3.6.4
LVD Enabled in Stop Mode
The LVD system is capable of generating either an interrupt or a reset when the supply voltage drops below
the LVD voltage. If the LVD is enabled in stop by setting the LVDE and the LVDSE bits, then the voltage
regulator remains active during stop mode. If the user attempts to enter stop2 with the LVD enabled for
stop, the MCU will instead enter stop3. Table 3-3 summarizes the behavior of the MCU in stop when the
LVD is enabled.
Table 3-3. LVD Enabled Stop Mode Behavior
CPU, Digital
Mode
PPDC Peripherals,
FLASH
RAM
ICG
ADC1
Regulator
I/O Pins
RTI
Stop3
0
Standby
Standby
Off1
Optionally on
Active
States
held
Optionally on
1
Crystal oscillator can be configured to run in stop3. Please see the ICG registers.
3.6.5
On-Chip Peripheral Modules in Stop Modes
When the MCU enters any stop mode, system clocks to the internal peripheral modules are stopped. Even
in the exception case (ENBDM = 1), where clocks to the background debug logic continue to operate,
clocks to the peripheral systems are halted to reduce power consumption. Refer to Section 3.6.1, “Stop2
Mode,” and Section 3.6.2, “Stop3 Mode,” for specific information on system behavior in stop modes.
Table 3-4. Stop Mode Behavior
Mode
Peripheral
Stop2
Stop3
CPU
Off
Standby
Off
Standby
Standby
RAM
FLASH
Standby
Parallel Port Registers
Off
Standby
ADC1
ICG
IIC
Off
Optionally On1
Optionally On2
Standby
Off
Off
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
37
Chapter 3 Modes of Operation
Table 3-4. Stop Mode Behavior (continued)
Mode
Peripheral
Stop2
Stop3
KBI
RTI
SCI
SPI
TPM
Off
Optionally On4
Off
Optionally On3
Optionally On4
Standby
Off
Standby
Off
Standby
Voltage Regulator
I/O Pins
Standby
States Held
Standby
States Held
1
2
3
4
Requires the asynchronous ADC clock and LVD to be enabled, else in
standby.
OSCSTEN set in ICSC1, else in standby. For high frequency range (RANGE
in ICSC2 set) requires the LVD to also be enabled in stop3.
During stop3, KBI pins that are enabled continue to function as interrupt
sources that are capable of waking the MCU from stop3.
This RTI can be enabled to run in stop2 or stop3 with the internal RTI clock
source (RTICLKS = 0, in SRTISC). The RTI also can be enabled to run in
stop3 with the external clock source (RTICLKS = 1 and OSCSTEN = 1).
MC9S08AW60 Data Sheet, Rev 2
38
Freescale Semiconductor
Chapter 4
Memory
4.1
MC9S08AW60 Series Memory Map
Figure 4-1 shows the memory map for the MC9S08AW60 and MC9S08AW48 MCUs. Figure 4-2 shows
the memory map for the MC9S08AW32 and MC9S08AW16 MCUs. On-chip memory in the
MC9S08AW60 Series of MCUs consists of RAM, FLASH program memory for nonvolatile data storage,
plus I/O and control/status registers. The registers are divided into three groups:
•
•
•
Direct-page registers ($0000 through $006F)
High-page registers ($1800 through $185F)
Nonvolatile registers ($FFB0 through $FFBF)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
39
Chapter 4 Memory
$0000
$0000
DIRECT PAGE REGISTERS
DIRECT PAGE REGISTERS
$006F
$0070
$006F
$0070
RAM
RAM
2048 BYTES
2048 BYTES
$086F
$0870
$086F
$0870
FLASH
RESERVED
3984 BYTES
3984 BYTES
$17FF
$1800
$17FF
$1800
HIGH PAGE REGISTERS
HIGH PAGE REGISTERS
$185F
$1860
$185F
$1860
RESERVED
10,144 BYTES
$3FFF
$4000
FLASH
59,296 BYTES
FLASH
49,152 BYTES
$FFFF
$FFFF
MC9S08AW48
MC9S08AW60
Figure 4-1. MC9S08AW60 and MC9S08AW48 Memory Map
MC9S08AW60 Data Sheet, Rev 2
40
Freescale Semiconductor
Chapter 4 Memory
$0000
$0000
DIRECT PAGE REGISTERS
DIRECT PAGE REGISTERS
$006F
$0070
$006F
$0070
RAM
RAM
1024 BYTES
$046F
$0470
2048 BYTES
$086F
$0870
RESERVED
5008 BYTES
RESERVED
3984 BYTES
$17FF
$1800
$17FF
$1800
HIGH PAGE REGISTERS
HIGH PAGE REGISTERS
$185F
$1860
$185F
$1860
RESERVED
RESERVED
42,912 BYTES
26,528 BYTES
$7FFF
$8000
$BFFF
$C000
FLASH
FLASH
16,384 BYTES
32,768 BYTES
$FFFF
$FFFF
MC9S08AW16
MC9S08AW32
Figure 4-2. MC9S08AW32 and MC9S08AW16 Memory Map
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
41
Chapter 4 Memory
4.1.1
Reset and Interrupt Vector Assignments
Figure 4-1 shows address assignments for reset and interrupt vectors. The vector names shown in this table
are the labels used in the Freescale-provided equate file for the MC9S08AW60 Series. For more details
about resets, interrupts, interrupt priority, and local interrupt mask controls, refer to Chapter 5, “Resets,
Interrupts, and System Configuration.”
Table 4-1. Reset and Interrupt Vectors
Address
(High/Low)
Vector
Vector Name
$FFC0:FFC1
Unused Vector Space
(available for user program)
$FFCA:FFCB
$FFCC:FFCD
$FFCE:FFCF
$FFD0:FFD1
$FFD2:FFD3
$FFD4:FFD5
$FFD6:FFD7
$FFD8:FFD9
$FFDA:FFDB
$FFDC:FFDD
$FFDE:FFDF
$FFE0:FFE1
$FFE2:FFE3
$FFE4:FFE5
$FFE6:FFE7
$FFE8:FFE9
$FFEA:FFEB
$FFEC:FFED
$FFEE:FFEF
$FFF0:FFF1
$FFF2:FFF3
$FFF4:FFF5
$FFF6:FFF7
$FFF8:FFF9
$FFFA:FFFB
$FFFC:FFFD
$FFFE:FFFF
RTI
IIC1
Vrti
Viic1
ADC1 Conversion
KBI1
Vadc1
Vkeyboard1
Vsci2tx
Vsci2rx
Vsci2err
Vsci1tx
Vsci1rx
Vsci1err
Vspi1
SCI2 Transmit
SCI2 Receive
SCI2 Error
SCI1 Transmit
SCI1 Receive
SCI1 Error
SPI1
TPM2 Overflow
TPM2 Channel 1
TPM2 Channel 0
TPM1 Overflow
TPM1 Channel 5
TPM1 Channel 4
TPM1 Channel 3
TPM1 Channel 2
TPM1 Channel 1
TPM1 Channel 0
ICG
Vtpm2ovf
Vtpm2ch1
Vtpm2ch0
Vtpm1ovf
Vtpm1ch5
Vtpm1ch4
Vtpm1ch3
Vtpm1ch2
Vtpm1ch1
Vtpm1ch0
Vicg
Low Voltage Detect
IRQ
Vlvd
Virq
SWI
Vswi
Reset
Vreset
MC9S08AW60 Data Sheet, Rev 2
42
Freescale Semiconductor
Chapter 4 Memory
4.2
Register Addresses and Bit Assignments
The registers in the MC9S08AW60 Series are divided into these three groups:
•
•
•
Direct-page registers are located in the first 112 locations in the memory map, so they are
accessible with efficient direct addressing mode instructions.
High-page registers are used much less often, so they are located above $1800 in the memory map.
This leaves more room in the direct page for more frequently used registers and variables.
The nonvolatile register area consists of a block of 16 locations in FLASH memory at
$FFB0–$FFBF.
Nonvolatile register locations include:
— Three values which are loaded into working registers at reset
— An 8-byte backdoor comparison key which optionally allows a user to gain controlled access
to secure memory
Because the nonvolatile register locations are FLASH memory, they must be erased and
programmed like other FLASH memory locations.
Direct-page registers can be accessed with efficient direct addressing mode instructions. Bit manipulation
instructions can be used to access any bit in any direct-page register. Table 4-2 is a summary of all
user-accessible direct-page registers and control bits.
The direct page registers in Table 4-2 can use the more efficient direct addressing mode which only
requires the lower byte of the address. Because of this, the lower byte of the address in column one is
shown in bold text. In Table 4-3 and Table 4-4 the whole address in column one is shown in bold. In
Table 4-2, Table 4-3, and Table 4-4, the register names in column two are shown in bold to set them apart
from the bit names to the right. Cells that are not associated with named bits are shaded. A shaded cell with
a 0 indicates this unused bit always reads as a 0. Shaded cells with dashes indicate unused or reserved bit
locations that could read as 1s or 0s.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
43
Chapter 4 Memory
Table 4-2. Direct-Page Register Summary (Sheet 1 of 3)
Address Register Name
Bit 7
6
5
4
3
2
1
Bit 0
PTAD7
PTADD7
PTBD7
PTAD6
PTADD6
PTBD6
PTAD5
PTADD5
PTBD5
PTAD4
PTADD4
PTBD4
PTAD3
PTADD3
PTBD3
PTAD2
PTADD2
PTBD2
PTAD1
PTADD1
PTBD1
PTAD0
PTADD0
PTBD0
$0000
$0001
$0002
$0003
$0004
$0005
$0006
$0007
$0008
$0009
$000A
$000B
$000C
$000D
PTAD
PTADD
PTBD
PTBDD7 PTBDD6 PTBDD5 PTBDD4 PTBDD3 PTBDD2 PTBDD1 PTBDD0
PTBDD
PTCD
0
0
PTCD6
PTCDD6 PTCDD5 PTCDD4 PTCDD3 PTCDD2 PTCDD1 PTCDD0
PTDD6 PTDD5 PTDD4 PTDD3 PTDD2 PTDD1 PTDD0
PTCD5
PTCD4
PTCD3
PTCD2
PTCD1
PTCD0
PTCDD
PTDD
PTDD7
PTDDD7 PTDDD6 PTDDD5 PTDDD4 PTDDD3 PTDDD2 PTDDD1 PTDDD0
PTED7 PTED6 PTED5 PTED4 PTED3 PTED2 PTED1 PTED0
PTEDD7 PTEDD6 PTEDD5 PTEDD4 PTEDD3 PTEDD2 PTEDD1 PTEDD0
PTFD7 PTFD6 PTFD5 PTFD4 PTFD3 PTFD2 PTFD1 PTFD0
PTFDD7 PTFDD6 PTFDD5 PTFDD4 PTFDD3 PTFDD2 PTFDD1 PTFDD0
PTDDD
PTED
PTEDD
PTFD
PTFDD
PTGD
0
0
PTGD6
PTGD5
PTGD4
PTGD3
PTGD2
PTGD1
PTGD0
PTGDD6 PTGDD5 PTGDD4 PTGDD3 PTGDD2 PTGDD1 PTGDD0
PTGDD
$000E–
$000F
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
COCO
ADACT
0
AIEN
ADTRG
0
ADCO
ACFE
0
ADCH
$0010
$0011
$0012
$0013
$0014
$0015
$0016
$0017
$0018
$0019
ADC1SC1
ADC1SC2
ADC1RH
ADC1RL
ADC1CVH
ADC1CVL
ADC1CFG
APCTL1
ACFGT
0
0
0
0
0
R
R
ADR9
ADR1
ADCV9
ADCV1
ADR8
ADR0
ADCV8
ADCV0
ADR7
0
ADR6
0
ADR5
0
ADR4
0
ADR3
0
ADR2
0
ADCV7
ADLPC
ADPC7
ADCV6
ADCV5
ADCV4
ADLSMP
ADPC4
ADCV3
ADCV2
ADIV
ADPC6
MODE
ADICLK
ADPC5
ADPC3
ADPC2
ADPC1
ADPC9
ADPC0
ADPC8
ADPC15 ADPC14 ADPC13 ADPC12 ADPC11 ADPC10
APCTL2
ADPC23 ADPC22 ADPC21 ADPC20 ADPC19 ADPC18 ADPC17 ADPC16
APCTL3
$001A–
$001B
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
0
0
IRQEDG
—
IRQPE
—
IRQF
—
IRQACK
IRQIE
IRQMOD
—
$001C
$001D
$001E
$001F
$0020
$0021
$0022
$0023
$0024
$0025
$0026
$0027
IRQSC
—
—
—
KBACK
KBIPE2
PS2
10
—
Reserved
KBEDG7 KBEDG6 KBEDG5 KBEDG4
KBF
KBIPE3
CLKSA
11
KBIE
KBIMOD
KBIPE0
PS0
KBI1SC
KBIPE7
TOF
KBIPE6
KBIPE5
KBIPE4
KBIPE1
KBI1PE
TOIE
CPWMS
CLKSB
PS1
9
TPM1SC
Bit 15
Bit 7
14
13
5
12
4
Bit 8
TPM1CNTH
TPM1CNTL
TPM1MODH
TPM1MODL
TPM1C0SC
TPM1C0VH
TPM1C0VL
6
14
3
2
1
Bit 0
Bit 15
Bit 7
13
5
12
4
11
10
9
Bit 8
6
3
2
1
Bit 0
CH0F
Bit 15
Bit 7
CH0IE
14
MS0B
13
5
MS0A
12
4
ELS0B
11
ELS0A
10
0
0
9
Bit 8
6
3
2
1
Bit 0
MC9S08AW60 Data Sheet, Rev 2
44
Freescale Semiconductor
Chapter 4 Memory
Bit 0
Table 4-2. Direct-Page Register Summary (Sheet 2 of 3)
Address Register Name
Bit 7
6
5
4
3
2
1
CH1F
Bit 15
Bit 7
CH2F
Bit 15
Bit 7
CH3F
Bit 15
Bit 7
CH4F
Bit 15
Bit 7
CH5F
Bit 15
Bit 7
—
CH1IE
MS1B
13
MS1A
12
ELS1B
11
ELS1A
10
0
9
1
0
9
1
0
9
1
0
9
1
0
9
1
0
$0028
$0029
$002A
$002B
$002C
$002D
$002E
$002F
$0030
$0031
$0032
$0033
$0034
$0035
$0036
$0037
$0038
$0039
$003A
$003B
$003C
$003D
$003E
$003F
$0040
$0041
$0042
$0043
$0044
$0045
$0046
$0047
$0048
$0049
$004A
$004B
$004C
$004D
$004E
$004F
TPM1C1SC
TPM1C1VH
TPM1C1VL
TPM1C2SC
TPM1C2VH
TPM1C2VL
TPM1C3SC
TPM1C3VH
TPM1C3VL
TPM1C4SC
TPM1C4VH
TPM1C4VL
TPM1C5SC
TPM1C5VH
TPM1C5VL
Reserved
SCI1BDH
SCI1BDL
SCI1C1
14
Bit 8
Bit 0
0
6
5
4
3
2
CH2IE
MS2B
13
MS2A
12
ELS2B
11
ELS2A
10
14
Bit 8
Bit 0
0
6
5
4
3
2
CH3IE
MS3B
13
MS3A
12
ELS3B
11
ELS3A
10
14
Bit 8
Bit 0
0
6
5
4
3
2
CH4IE
MS4B
13
MS4A
12
ELS4B
11
ELS4A
10
14
Bit 8
Bit 0
0
6
5
4
3
2
CH5IE
MS5B
13
MS5A
12
ELS5B
11
ELS5A
10
14
Bit 8
Bit 0
6
5
4
3
2
—
—
—
—
—
—
SBR9
SBR1
PE
—
SBR8
SBR0
PT
0
0
0
SBR12
SBR4
M
SBR11
SBR3
WAKE
TE
SBR10
SBR2
ILT
SBR7
LOOPS
TIE
SBR6
SBR5
RSRC
RIE
RDRF
0
SCISWAI
TCIE
ILIE
IDLE
0
RE
RWU
FE
SBK
PF
SCI1C2
TDRE
0
TC
OR
NF
SCI1S1
0
0
BRK13
NEIE
2
0
RAF
PEIE
Bit 0
SBR8
SBR0
PT
SCI1S2
R8
T8
TXDIR
5
TXINV
4
ORIE
3
FEIE
1
SCI1C3
Bit 7
0
6
0
SCI1D
0
SBR12
SBR4
M
SBR11
SBR3
WAKE
TE
SBR10
SBR2
ILT
SBR9
SBR1
PE
SCI2BDH
SCI2BDL
SCI2C1
SBR7
LOOPS
TIE
SBR6
SCISWAI
TCIE
TC
SBR5
RSRC
RIE
RDRF
0
ILIE
IDLE
0
RE
RWU
FE
SBK
PF
SCI2C2
TDRE
0
OR
NF
SCI2S1
0
0
BRK13
NEIE
2
0
RAF
PEIE
Bit 0
0
SCI2S2
R8
T8
TXDIR
5
TXINV
4
ORIE
3
FEIE
1
SCI2C3
Bit 7
HGO
LOLRE
6
SCI2D
RANGE
REFS
MFD
REFST
0
CLKS
OSCSTEN
LOCD
RFD
ERCS
0
ICGC1
LOCRE
LOCK
0
ICGC2
CLKST
LOLS
LOCS
0
ICGIF
DCOS
ICGS1
0
0
0
0
0
0
ICGS2
0
FLT
ICGFLTU
ICGFLTL
ICGTRM
Reserved
FLT
TRIM
—
—
—
—
—
—
—
—
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
45
Chapter 4 Memory
Table 4-2. Direct-Page Register Summary (Sheet 3 of 3)
Address Register Name
Bit 7
6
5
4
3
2
1
Bit 0
SPIE
0
SPE
SPTIE
MSTR
CPOL
CPHA
SSOE
LSBFE
SPC0
SPR0
0
$0050
$0051
$0052
$0053
$0054
$0055
SPI1C1
SPI1C2
SPI1BR
SPI1S
0
0
SPPR1
SPTEF
0
MODFEN BIDIROE
0
SPISWAI
0
SPPR2
SPPR0
0
0
0
3
SPR2
SPR1
SPRF
0
0
0
6
MODF
0
0
2
0
0
1
0
4
0
Reserved
SPI1D
Bit 7
5
Bit 0
$0056–
$0057
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
ADDR
0
$0058
$0059
$005A
$005B
$005C
IIC1A
IIC1F
IIC1C
IIC1S
IIC1D
MULT
ICR
IICEN
TCF
IICIE
IAAS
MST
TX
TXAK
0
RSTA
SRW
0
0
BUSY
ARBL
IICIF
RXAK
DATA
$005D–
$005F
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
TOF
Bit 15
Bit 7
TOIE
CPWMS
CLKSB
CLKSA
PS2
PS1
9
PS0
Bit 8
Bit 0
Bit 8
Bit 0
0
$0060
$0061
$0062
$0063
$0064
$0065
$0066
$0067
$0068
$0069
$006A
TPM2SC
14
13
5
12
4
11
10
TPM2CNTH
TPM2CNTL
TPM2MODH
TPM2MODL
TPM2C0SC
TPM2C0VH
TPM2C0VL
TPM2C1SC
TPM2C1VH
TPM2C1VL
6
14
3
2
1
Bit 15
Bit 7
13
12
11
10
9
6
5
4
3
ELS0B
11
2
ELS0A
10
1
CH0F
Bit 15
Bit 7
CH0IE
14
MS0B
13
MS0A
12
0
9
Bit 8
Bit 0
0
6
5
4
3
2
1
CH1F
Bit 15
Bit 7
CH1IE
14
MS1B
13
MS1A
12
ELS1B
11
ELS1A
10
0
9
Bit 8
Bit 0
6
5
4
3
2
1
$006B–
$006F
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
MC9S08AW60 Data Sheet, Rev 2
46
Freescale Semiconductor
Chapter 4 Memory
High-page registers, shown in Table 4-3, are accessed much less often than other I/O and control registers
so they have been located outside the direct addressable memory space, starting at $1800.
Table 4-3. High-Page Register Summary (Sheet 1 of 2)
Address Register Name
Bit 7
6
5
4
3
2
1
Bit 0
POR
PIN
0
COP
ILOP
0
0
0
0
0
ICG
0
LVD
0
0
BDFR
—
$1800
$1801
$1802
$1803
SRS
0
COPE
0
0
STOPE
0
SBDFR
SOPT
SMCLK
COPT
0
—
0
—
MPE
MCSEL
$1804 –
$1805
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
REV3
ID7
REV2
ID6
REV1
ID5
REV0
ID4
ID11
ID3
ID10
ID2
ID9
ID1
RTIS1
01
ID8
$1806
$1807
$1808
$1809
$180A
SDIDH
ID0
SDIDL
RTIF
LVDF
LVWF
RTIACK RTICLKS
RTIE
0
RTIS2
LVDE
RTIS0
BGBE
PPDC
SRTISC
SPMSC1
SPMSC2
LVDACK
LVWACK
LVDIE
LVDV
LVDRE
LVWV
LVDSE
PPDF
PPDACK
—
$180B–
$180F
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
Bit 15
Bit 7
14
6
13
5
12
11
3
10
2
9
Bit 8
Bit 0
$1810
$1811
$1812
$1813
$1814
$1815
$1816
$1817
$1818
DBGCAH
DBGCAL
DBGCBH
DBGCBL
DBGFH
DBGFL
DBGC
4
1
9
Bit 15
Bit 7
14
13
12
11
10
Bit 8
6
5
4
3
2
1
Bit 0
Bit 15
Bit 7
14
13
12
11
10
9
Bit 8
6
5
4
3
2
1
Bit 0
DBGEN
TRGSEL
AF
ARM
BEGIN
BF
TAG
0
BRKEN
RWA
TRG3
CNT3
RWAEN
TRG2
CNT2
RWB
TRG1
CNT1
RWBEN
TRG0
CNT0
0
0
DBGT
ARMF
DBGS
$1819–
$181F
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
DIVLD
KEYEN
—
PRDIV8
FNORED
—
DIV5
0
DIV4
0
DIV3
DIV2
0
DIV1
SEC01
—
DIV0
SEC00
—
$1820
$1821
$1822
$1823
$1824
$1825
$1826
FCDIV
FOPT
0
—
—
—
—
Reserved
FCNFG
FPROT
FSTAT
FCMD
0
0
KEYACC
FPS5
0
0
0
0
0
FPS7
FCBEF
FCMD7
FPS6
FCCF
FCMD6
FPS4
FPS3
0
FPS2
FBLANK
FCMD2
FPS1
0
FPDIS
0
FPVIOL FACCERR
FCMD5
FCMD4
FCMD3
FCMD1
FCMD0
$1827–
$183F
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
PTAPE7
PTASE7
PTADS7
—
PTAPE6
PTASE6
PTADS6
—
PTAPE5
PTASE5
PTADS5
—
PTAPE4
PTASE4
PTADS4
—
PTAPE3
PTASE3
PTADS3
—
PTAPE2
PTASE2
PTADS2
—
PTAPE1
PTASE1
PTADS1
—
PTAPE0
PTASE0
PTADS0
—
$1840
$1841
$1842
$1843
$1844
$1845
PTAPE
PTASE
PTADS
Reserved
PTBPE
PTBSE
PTBPE7
PTBSE7
PTBPE6
PTBSE6
PTBPE5
PTBSE5
PTBPE4
PTBSE4
PTBPE3
PTBSE3
PTBPE2
PTBSE2
PTBPE1
PTBSE1
PTBPE0
PTBSE0
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
47
Chapter 4 Memory
Table 4-3. High-Page Register Summary (Sheet 2 of 2)
Address Register Name
Bit 7
6
5
4
3
2
1
Bit 0
PTBDS7 PTBDS6 PTBDS5 PTBDS4 PTBDS3 PTBDS2 PTBDS1 PTBDS0
$1846
$1847
$1848
$1849
$184A
$184B
$184C
$184D
$184E
$184F
$1850
$1851
$1852
$1853
$1854
$1855
$1856
$1857
$1858
$1859
$185A
PTBDS
Reserved
PTCPE
PTCSE
PTCDS
Reserved
PTDPE
PTDSE
PTDDS
Reserved
PTEPE
PTESE
PTEDS
Reserved
PTFPE
—
0
—
—
—
—
—
—
—
PTCPE6 PTCPE5 PTCPE4 PTCPE3 PTCPE2 PTCPE1 PTCPE0
PTCSE6 PTCSE5 PTCSE4 PTCSE3 PTCSE2 PTCSE1 PTCSE0
PTCDS6 PTCDS5 PTCDS4 PTCDS3 PTCDS2 PTCDS1 PTCDS0
0
0
—
—
—
—
—
—
—
—
PTDPE7 PTDPE6 PTDPE5 PTDPE4 PTDPE3 PTDPE2 PTDPE1 PTDPE0
PTDSE7 PTDSE6 PTDSE5 PTDSE4 PTDSE3 PTDSE2 PTDSE1 PTDSE0
PTDDS7 PTDDS6 PTDDS5 PTDDS4 PTDDS3 PTDDS2 PTDDS1 PTDDS0
—
—
—
—
—
—
—
—
PTEPE7
PTESE7
PTEPE6
PTESE6
PTEPE5
PTESE5
PTEPE4
PTESE4
PTEPE3
PTESE3
PTEPE2
PTESE2
PTEPE1
PTESE1
PTEPE0
PTESE0
PTEDS7 PTEDS6 PTEDS5 PTEDS4 PTEDS3 PTEDS2 PTEDS1 PTEDS0
—
—
—
—
—
—
—
—
PTFPE7
PTFPE6
PTFSE6
PTFDS6
—
PTFPE5
PTFSE5
PTFDS5
—
PTFPE4
PTFSE4
PTFDS4
—
PTFPE3
PTFSE3
PTFDS3
—
PTFPE2
PTFSE2
PTFDS2
—
PTFPE1
PTFSE1
PTFDS1
—
PTFPE0
PTFSE0
PTFDS0
—
PTFSE7
PTFSE
PTFDS7
PTFDS
Reserved
PTGPE
PTGSE
PTGDS
—
0
PTGPE6 PTGPE5 PTGPE4 PTGPE3 PTGPE2 PTGPE1 PTGPE0
PTGSE6 PTGSE5 PTGSE4 PTGSE3 PTGSE2 PTGSE1 PTGSE0
PTGDS6 PTGDS5 PTGDS4 PTGDS3 PTGDS2 PTGDS1 PTGDS0
0
0
$185B–
$185F
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
1
This reserved bit must always be written to 0.
Nonvolatile FLASH registers, shown in Table 4-4, are located in the FLASH memory. These registers
include an 8-byte backdoor key which optionally can be used to gain access to secure memory resources.
During reset events, the contents of NVPROT and NVOPT in the nonvolatile register area of the FLASH
memory are transferred into corresponding FPROT and FOPT working registers in the high-page registers
to control security and block protection options.
MC9S08AW60 Data Sheet, Rev 2
48
Freescale Semiconductor
Chapter 4 Memory
Table 4-4. Nonvolatile Register Summary
Address Register Name
Bit 7
6
5
4
3
2
1
Bit 0
$FFB0 – NVBACKKEY
$FFB7
8-Byte Comparison Key
$FFB8 – Reserved
$FFBB
—
—
—
—
—
—
—
—
$FFBC
Reserved for stor-
age of 250 kHz
ICGTRM value
—
FPS7
—
—
FPS6
—
—
FPS5
—
—
FPS4
—
—
FPS3
—
—
FPS2
—
—
FPS1
—
—
FPDIS
—
$FFBD
$FFBE
NVPROT
Reserved for stor-
age of 243 kHz
ICGTRM value
KEYEN
FNORED
0
0
0
0
SEC01
SEC00
$FFBF
NVOPT
Provided the key enable (KEYEN) bit is 1, the 8-byte comparison key can be used to temporarily
disengage memory security. This key mechanism can be accessed only through user code running in secure
memory. (A security key cannot be entered directly through background debug commands.) This security
key can be disabled completely by programming the KEYEN bit to 0. If the security key is disabled, the
only way to disengage security is by mass erasing the FLASH if needed (normally through the background
debug interface) and verifying that FLASH is blank. To avoid returning to secure mode after the next reset,
program the security bits (SEC01:SEC00) to the unsecured state (1:0).
4.3
RAM
The MC9S08AW60 Series includes static RAM. The locations in RAM below $0100 can be accessed
using the more efficient direct addressing mode, and any single bit in this area can be accessed with the bit
manipulation instructions (BCLR, BSET, BRCLR, and BRSET). Locating the most frequently accessed
program variables in this area of RAM is preferred.
The RAM retains data when the MCU is in low-power wait, stop2, or stop3 mode. At power-on, the
contents of RAM are uninitialized. RAM data is unaffected by any reset provided that the supply voltage
does not drop below the minimum value for RAM retention.
For compatibility with older M68HC05 MCUs, the HCS08 resets the stack pointer to $00FF. In the
MC9S08AW60 Series, it is usually best to re-initialize the stack pointer to the top of the RAM so the direct
page RAM can be used for frequently accessed RAM variables and bit-addressable program variables.
Include the following 2-instruction sequence in your reset initialization routine (where RamLast is equated
to the highest address of the RAM in the Freescale-provided equate file).
LDHX
TXS
#RamLast+1
;point one past RAM
;SP<-(H:X-1)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
49
Chapter 4 Memory
When security is enabled, the RAM is considered a secure memory resource and is not accessible through
BDM or through code executing from non-secure memory. See Section 4.5, “Security” for a detailed
description of the security feature.
4.4
FLASH
The FLASH memory is intended primarily for program storage. In-circuit programming allows the
operating program to be loaded into the FLASH memory after final assembly of the application product.
It is possible to program the entire array through the single-wire background debug interface. Because no
special voltages are needed for FLASH erase and programming operations, in-application programming
is also possible through other software-controlled communication paths. For a more detailed discussion of
in-circuit and in-application programming, refer to the HCS08 Family Reference Manual, Volume I,
Freescale Semiconductor document order number HCS08RMv1/D.
MC9S08AW60 Data Sheet, Rev 2
50
Freescale Semiconductor
Chapter 4 Memory
4.4.1
Features
Features of the FLASH memory include:
•
FLASH Size
— MC9S08AW60 — 63280 bytes (124 pages of 512 bytes each)
— MC9S08AW48 — 49152 bytes (96 pages of 512 bytes each)
— MC9S08AW32 — 32768 bytes (64 pages of 512 bytes each)
— MC9S08AW16 — 16384 bytes (32 pages of 512 bytes each)
Single power supply program and erase
•
•
•
•
•
•
Command interface for fast program and erase operation
Up to 100,000 program/erase cycles at typical voltage and temperature
Flexible block protection
Security feature for FLASH and RAM
Auto power-down for low-frequency read accesses
4.4.2
Program and Erase Times
Before any program or erase command can be accepted, the FLASH clock divider register (FCDIV) must
be written to set the internal clock for the FLASH module to a frequency (f ) between 150 kHz and
FCLK
200 kHz (see Section 4.6.1, “FLASH Clock Divider Register (FCDIV)”). This register can be written only
once, so normally this write is done during reset initialization. FCDIV cannot be written if the access error
flag, FACCERR in FSTAT, is set. The user must ensure that FACCERR is not set before writing to the
FCDIV register. One period of the resulting clock (1/f
) is used by the command processor to time
FCLK
program and erase pulses. An integer number of these timing pulses are used by the command processor
to complete a program or erase command.
Table 4-5 shows program and erase times. The bus clock frequency and FCDIV determine the frequency
of FCLK (f
). The time for one cycle of FCLK is t
= 1/f
. The times are shown as a number
FCLK
FCLK
FCLK
of cycles of FCLK and as an absolute time for the case where t
shown include overhead for the command state machine and enabling and disabling of program and erase
voltages.
= 5 μs. Program and erase times
FCLK
Table 4-5. Program and Erase Times
Parameter
Byte program
Cycles of FCLK
Time if FCLK = 200 kHz
9
4
45 μs
20 μs1
20 ms2
Byte program (burst)
Page erase
4000
20,000
Mass erase
100 ms2
1
2
Excluding start/end overhead
Because the page and mass erase times can be longer than the COP watchdog timeout, the
COP should be serviced during any software erase routine.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
51
Chapter 4 Memory
4.4.3
Program and Erase Command Execution
The steps for executing any of the commands are listed below. The FCDIV register must be initialized and
any error flags cleared before beginning command execution. The command execution steps are:
1. Write a data value to an address in the FLASH array. The address and data information from this
write is latched into the FLASH interface. This write is a required first step in any command
sequence. For erase and blank check commands, the value of the data is not important. For page
erase commands, the address may be any address in the 512-byte page of FLASH to be erased. For
mass erase and blank check commands, the address can be any address in the FLASH memory.
Whole pages of 512 bytes are the smallest block of FLASH that may be erased. In the 60K version,
there are two instances where the size of a block that is accessible to the user is less than 512 bytes:
the first page following RAM, and the first page following the high page registers. These pages are
overlapped by the RAM and high page registers respectively.
NOTE
Do not program any byte in the FLASH more than once after a successful
erase operation. Reprogramming bits to a byte which is already
programmed is not allowed without first erasing the page in which the byte
resides or mass erasing the entire FLASH memory. Programming without
first erasing may disturb data stored in the FLASH.
2. Write the command code for the desired command to FCMD. The five valid commands are blank
check ($05), byte program ($20), burst program ($25), page erase ($40), and mass erase ($41).
The command code is latched into the command buffer.
3. Write a 1 to the FCBEF bit in FSTAT to clear FCBEF and launch the command (including its
address and data information).
A partial command sequence can be aborted manually by writing a 0 to FCBEF any time after the write to
the memory array and before writing the 1 that clears FCBEF and launches the complete command.
Aborting a command in this way sets the FACCERR access error flag which must be cleared before
starting a new command.
A strictly monitored procedure must be obeyed or the command will not be accepted. This minimizes the
possibility of any unintended changes to the FLASH memory contents. The command complete flag
(FCCF) indicates when a command is complete. The command sequence must be completed by clearing
FCBEF to launch the command. Figure 4-3 is a flowchart for executing all of the commands except for
burst programming. The FCDIV register must be initialized before using any FLASH commands. This
only must be done once following a reset.
MC9S08AW60 Data Sheet, Rev 2
52
Freescale Semiconductor
Chapter 4 Memory
(Note 1)
Note 1: Required only once after reset.
WRITE TO FCDIV
START
FLASH PROGRAM AND
ERASE FLOW
0
FACCERR ?
1
CLEAR ERROR
WRITE TO FLASH
TO BUFFER ADDRESS AND DATA
WRITE COMMAND TO FCMD
WRITE 1 TO FCBEF
Note 2: Wait at least four bus cycles
before checking FCBEF or FCCF.
TO LAUNCH COMMAND
(Note 2)
AND CLEAR FCBEF
YES
FPVIOL OR
FACCERR ?
ERROR EXIT
NO
0
FCCF ?
1
DONE
Figure 4-3. FLASH Program and Erase Flowchart
4.4.4
Burst Program Execution
The burst program command is used to program sequential bytes of data in less time than would be
required using the standard program command. This is possible because the high voltage to the FLASH
array does not need to be disabled between program operations. Ordinarily, when a program or erase
command is issued, an internal charge pump associated with the FLASH memory must be enabled to
supply high voltage to the array. Upon completion of the command, the charge pump is turned off. When
a burst program command is issued, the charge pump is enabled and then remains enabled after completion
of the burst program operation if these two conditions are met:
•
The next burst program command has been queued before the current program operation has
completed.
•
The next sequential address selects a byte on the same physical row as the current byte being
programmed. A row of FLASH memory consists of 64 bytes. A byte within a row is selected by
addresses A5 through A0. A new row begins when addresses A5 through A0 are all zero.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
53
Chapter 4 Memory
The first byte of a series of sequential bytes being programmed in burst mode will take the same amount
of time to program as a byte programmed in standard mode. Subsequent bytes will program in the burst
program time provided that the conditions above are met. In the case the next sequential address is the
beginning of a new row, the program time for that byte will be the standard time instead of the burst time.
This is because the high voltage to the array must be disabled and then enabled again. If a new burst
command has not been queued before the current command completes, then the charge pump will be
disabled and high voltage removed from the array.
(Note 1)
Note 1: Required only once after reset.
WRITE TO FCDIV
FLASH BURST
PROGRAM FLOW
START
0
FACCERR ?
1
CLEAR ERROR
0
FCBEF ?
1
WRITE TO FLASH
TO BUFFER ADDRESS AND DATA
WRITE COMMAND ($25) TO FCMD
WRITE 1 TO FCBEF
Note 2: Wait at least four bus cycles before
checking FCBEF or FCCF.
TO LAUNCH COMMAND
(Note 2)
AND CLEAR FCBEF
YES
FPVIO OR
FACCERR ?
ERROR EXIT
NO
YES
NEW BURST COMMAND ?
NO
0
FCCF ?
1
DONE
Figure 4-4. FLASH Burst Program Flowchart
MC9S08AW60 Data Sheet, Rev 2
54
Freescale Semiconductor
Chapter 4 Memory
4.4.5
Access Errors
An access error occurs whenever the command execution protocol is violated.
Any of the following specific actions will cause the access error flag (FACCERR) in FSTAT to be set.
FACCERR must be cleared by writing a 1 to FACCERR in FSTAT before any command can be processed.
•
•
•
•
Writing to a FLASH address before the internal FLASH clock frequency has been set by writing
to the FCDIV register
Writing to a FLASH address while FCBEF is not set (A new command cannot be started until the
command buffer is empty.)
Writing a second time to a FLASH address before launching the previous command (There is only
one write to FLASH for every command.)
Writing a second time to FCMD before launching the previous command (There is only one write
to FCMD for every command.)
•
•
Writing to any FLASH control register other than FCMD after writing to a FLASH address
Writing any command code other than the five allowed codes ($05, $20, $25, $40, or $41) to
FCMD
•
•
•
Accessing (read or write) any FLASH control register other than the write to FSTAT (to clear
FCBEF and launch the command) after writing the command to FCMD.
The MCU enters stop mode while a program or erase command is in progress (The command is
aborted.)
Writing the byte program, burst program, or page erase command code ($20, $25, or $40) with a
background debug command while the MCU is secured (The background debug controller can
only do blank check and mass erase commands when the MCU is secure.)
•
Writing 0 to FCBEF to cancel a partial command
4.4.6
FLASH Block Protection
The block protection feature prevents the protected region of FLASH from program or erase changes.
Block protection is controlled through the FLASH Protection Register (FPROT). When enabled, block
protection begins at any 512 byte boundary below the last address of FLASH, $FFFF. (see Section 4.6.4,
“FLASH Protection Register (FPROT and NVPROT)”).
After exit from reset, FPROT is loaded with the contents of the NVPROT location which is in the
nonvolatile register block of the FLASH memory. FPROT cannot be changed directly from application
software so a runaway program cannot alter the block protection settings. Since NVPROT is within the last
512 bytes of FLASH, if any amount of memory is protected, NVPROT is itself protected and cannot be
altered (intentionally or unintentionally) by the application software. FPROT can be written through
background debug commands which allows a way to erase and reprogram a protected FLASH memory.
The block protection mechanism is illustrated below. The FPS bits are used as the upper bits of the last
address of unprotected memory. This address is formed by concatenating FPS7:FPS1 with logic 1 bits as
shown. For example, in order to protect the last 8192 bytes of memory (addresses $E000 through $FFFF),
the FPS bits must be set to 1101 111 which results in the value $DFFF as the last address of unprotected
memory. In addition to programming the FPS bits to the appropriate value, FPDIS (bit 0 of NVPROT) must
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
55
Chapter 4 Memory
be programmed to logic 0 to enable block protection. Therefore the value $DE must be programmed into
NVPROT to protect addresses $E000 through $FFFF.
FPS7 FPS6 FPS5 FPS4 FPS3 FPS2 FPS1
1
1
1
1
1
1
1
1
1
A15 A14
A13
A12
A11
A10
A9
A8 A7 A6 A5 A4 A3 A2 A1 A0
Figure 4-5. Block Protection Mechanism
One use for block protection is to block protect an area of FLASH memory for a bootloader program. This
bootloader program then can be used to erase the rest of the FLASH memory and reprogram it. Because
the bootloader is protected, it remains intact even if MCU power is lost in the middle of an erase and
reprogram operation.
4.4.7
Vector Redirection
Whenever any block protection is enabled, the reset and interrupt vectors will be protected. Vector
redirection allows users to modify interrupt vector information without unprotecting bootloader and reset
vector space. Vector redirection is enabled by programming the FNORED bit in the NVOPT register
located at address $FFBF to zero. For redirection to occur, at least some portion but not all of the FLASH
memory must be block protected by programming the NVPROT register located at address $FFBD. All of
the interrupt vectors (memory locations $FFC0–$FFFD) are redirected, though the reset vector
($FFFE:FFFF) is not.
For example, if 512 bytes of FLASH are protected, the protected address region is from $FE00 through
$FFFF. The interrupt vectors ($FFC0–$FFFD) are redirected to the locations $FDC0–$FDFD. Now, if an
SPI interrupt is taken for instance, the values in the locations $FDE0:FDE1 are used for the vector instead
of the values in the locations $FFE0:FFE1. This allows the user to reprogram the unprotected portion of
the FLASH with new program code including new interrupt vector values while leaving the protected area,
which includes the default vector locations, unchanged.
4.5
Security
The MC9S08AW60 Series includes circuitry to prevent unauthorized access to the contents of FLASH and
RAM memory. When security is engaged, FLASH and RAM are considered secure resources. Direct-page
registers, high-page registers, and the background debug controller are considered unsecured resources.
Programs executing within secure memory have normal access to any MCU memory locations and
resources. Attempts to access a secure memory location with a program executing from an unsecured
memory space or through the background debug interface are blocked (writes are ignored and reads return
all 0s).
Security is engaged or disengaged based on the state of two nonvolatile register bits (SEC01:SEC00) in
the FOPT register. During reset, the contents of the nonvolatile location NVOPT are copied from FLASH
into the working FOPT register in high-page register space. A user engages security by programming the
NVOPT location which can be done at the same time the FLASH memory is programmed. The 1:0 state
disengages security and the other three combinations engage security. Notice the erased state (1:1) makes
MC9S08AW60 Data Sheet, Rev 2
56
Freescale Semiconductor
Chapter 4 Memory
the MCU secure. During development, whenever the FLASH is erased, it is good practice to immediately
program the SEC00 bit to 0 in NVOPT so SEC01:SEC00 = 1:0. This would allow the MCU to remain
unsecured after a subsequent reset.
The on-chip debug module cannot be enabled while the MCU is secure. The separate background debug
controller can still be used for background memory access commands, but the MCU cannot enter active
background mode except by holding BKGD/MS low at the rising edge of reset.
A user can choose to allow or disallow a security unlocking mechanism through an 8-byte backdoor
security key. If the nonvolatile KEYEN bit in NVOPT/FOPT is 0, the backdoor key is disabled and there
is no way to disengage security without completely erasing all FLASH locations. If KEYEN is 1, a secure
user program can temporarily disengage security by:
1. Writing 1 to KEYACC in the FCNFG register. This makes the FLASH module interpret writes to
the backdoor comparison key locations (NVBACKKEY through NVBACKKEY+7) as values to
be compared against the key rather than as the first step in a FLASH program or erase command.
2. Writing the user-entered key values to the NVBACKKEY through NVBACKKEY+7 locations.
These writes must be done in order starting with the value for NVBACKKEY and ending with
NVBACKKEY+7. STHX should not be used for these writes because these writes cannot be done
on adjacent bus cycles. User software normally would get the key codes from outside the MCU
system through a communication interface such as a serial I/O.
3. Writing 0 to KEYACC in the FCNFG register. If the 8-byte key that was just written matches the
key stored in the FLASH locations, SEC01:SEC00 are automatically changed to 1:0 and security
will be disengaged until the next reset.
The security key can be written only from secure memory (either RAM or FLASH), so it cannot be entered
through background commands without the cooperation of a secure user program.
The backdoor comparison key (NVBACKKEY through NVBACKKEY+7) is located in FLASH memory
locations in the nonvolatile register space so users can program these locations exactly as they would
program any other FLASH memory location. The nonvolatile registers are in the same 512-byte block of
FLASH as the reset and interrupt vectors, so block protecting that space also block protects the backdoor
comparison key. Block protects cannot be changed from user application programs, so if the vector space
is block protected, the backdoor security key mechanism cannot permanently change the block protect,
security settings, or the backdoor key.
Security can always be disengaged through the background debug interface by taking these steps:
1. Disable any block protections by writing FPROT. FPROT can be written only with background
debug commands, not from application software.
2. Mass erase FLASH if necessary.
3. Blank check FLASH. Provided FLASH is completely erased, security is disengaged until the next
reset.
To avoid returning to secure mode after the next reset, program NVOPT so SEC01:SEC00 = 1:0.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
57
Chapter 4 Memory
4.6
FLASH Registers and Control Bits
The FLASH module has nine 8-bit registers in the high-page register space, three locations in the
nonvolatile register space in FLASH memory which are copied into three corresponding high-page control
registers at reset. There is also an 8-byte comparison key in FLASH memory. Refer to Table 4-3 and
Table 4-4 for the absolute address assignments for all FLASH registers. This section refers to registers and
control bits only by their names. A Freescale-provided equate or header file normally is used to translate
these names into the appropriate absolute addresses.
4.6.1
FLASH Clock Divider Register (FCDIV)
Bit 7 of this register is a read-only status flag. Bits 6 through 0 may be read at any time but can be written
only one time. Before any erase or programming operations are possible, write to this register to set the
frequency of the clock for the nonvolatile memory system within acceptable limits.
7
6
5
4
3
2
1
0
R
W
DIVLD
PRDIV8
DIV5
DIV4
DIV3
DIV2
DIV1
DIV0
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 4-6. FLASH Clock Divider Register (FCDIV)
Table 4-6. FCDIV Register Field Descriptions
Description
Field
7
Divisor Loaded Status Flag — When set, this read-only status flag indicates that the FCDIV register has been
written since reset. Reset clears this bit and the first write to this register causes this bit to become set regardless
of the data written.
DIVLD
0 FCDIV has not been written since reset; erase and program operations disabled for FLASH.
1 FCDIV has been written since reset; erase and program operations enabled for FLASH.
6
Prescale (Divide) FLASH Clock by 8
PRDIV8
0 Clock input to the FLASH clock divider is the bus rate clock.
1 Clock input to the FLASH clock divider is the bus rate clock divided by 8.
5:0
DIV[5:0]
Divisor for FLASH Clock Divider — The FLASH clock divider divides the bus rate clock (or the bus rate clock
divided by 8 if PRDIV8 = 1) by the value in the 6-bit DIV5:DIV0 field plus one. The resulting frequency of the
internal FLASH clock must fall within the range of 200 kHz to 150 kHz for proper FLASH operations.
Program/Erase timing pulses are one cycle of this internal FLASH clock which corresponds to a range of 5 μs to
6.7 μs. The automated programming logic uses an integer number of these pulses to complete an erase or
program operation. See Equation 4-1, Equation 4-2, and Table 4-6.
if PRDIV8 = 0 — f
if PRDIV8 = 1 — f
= f
÷ ([DIV5:DIV0] + 1)
Bus
Eqn. 4-1
Eqn. 4-2
FCLK
= f
÷ (8 × ([DIV5:DIV0] + 1))
FCLK
Bus
Table 4-7 shows the appropriate values for PRDIV8 and DIV5:DIV0 for selected bus frequencies.
MC9S08AW60 Data Sheet, Rev 2
58
Freescale Semiconductor
Chapter 4 Memory
Table 4-7. FLASH Clock Divider Settings
PRDIV8
(Binary)
DIV5:DIV0
fFCLK
Program/Erase Timing Pulse
fBus
(Decimal)
(5 μs Min, 6.7 μs Max)
20 MHz
10 MHz
8 MHz
1
0
0
0
0
0
0
0
12
49
39
19
9
192.3 kHz
200 kHz
200 kHz
200 kHz
200 kHz
200 kHz
200 kHz
150 kHz
5.2 μs
5 μs
5 μs
4 MHz
5 μs
2 MHz
5 μs
1 MHz
4
5 μs
200 kHz
150 kHz
0
5 μs
0
6.7 μs
4.6.2
FLASH Options Register (FOPT and NVOPT)
During reset, the contents of the nonvolatile location NVOPT are copied from FLASH into FOPT. Bits 5
through 2 are not used and always read 0. This register may be read at any time, but writes have no meaning
or effect. To change the value in this register, erase and reprogram the NVOPT location in FLASH memory
as usual and then issue a new MCU reset.
7
6
5
4
3
2
1
0
R
W
KEYEN
FNORED
0
0
0
0
SEC01
SEC00
Reset
This register is loaded from nonvolatile location NVOPT during reset.
= Unimplemented or Reserved
Figure 4-7. FLASH Options Register (FOPT)
Table 4-8. FOPT Register Field Descriptions
Description
Field
7
Backdoor Key Mechanism Enable — When this bit is 0, the backdoor key mechanism cannot be used to
disengage security. The backdoor key mechanism is accessible only from user (secured) firmware. BDM
commands cannot be used to write key comparison values that would unlock the backdoor key. For more detailed
information about the backdoor key mechanism, refer to Section 4.5, “Security.”
KEYEN
0 No backdoor key access allowed.
1 If user firmware writes an 8-byte value that matches the nonvolatile backdoor key (NVBACKKEY through
NVBACKKEY+7 in that order), security is temporarily disengaged until the next MCU reset.
6
Vector Redirection Disable — When this bit is 1, then vector redirection is disabled.
FNORED 0 Vector redirection enabled.
1 Vector redirection disabled.
1:0
Security State Code — This 2-bit field determines the security state of the MCU as shown in Table 4-9. When
SEC0[1:0] the MCU is secure, the contents of RAM and FLASH memory cannot be accessed by instructions from any
unsecured source including the background debug interface. For more detailed information about security, refer
to Section 4.5, “Security.”
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
59
Chapter 4 Memory
Table 4-9. Security States
SEC01:SEC00
Description
0:0
0:1
1:0
1:1
secure
secure
unsecured
secure
SEC01:SEC00 changes to 1:0 after successful backdoor key entry or a successful blank check of FLASH.
4.6.3
FLASH Configuration Register (FCNFG)
Bits 7 through 5 may be read or written at any time. Bits 4 through 0 always read 0 and cannot be written.
7
6
5
4
3
2
1
0
R
W
0
0
0
0
0
0
0
KEYACC
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 4-8. FLASH Configuration Register (FCNFG)
Table 4-10. FCNFG Register Field Descriptions
Description
Field
5
Enable Writing of Access Key — This bit enables writing of the backdoor comparison key. For more detailed
information about the backdoor key mechanism, refer to Section 4.5, “Security.”
KEYACC
0 Writes to $FFB0–$FFB7 are interpreted as the start of a FLASH programming or erase command.
1 Writes to NVBACKKEY ($FFB0–$FFB7) are interpreted as comparison key writes.
MC9S08AW60 Data Sheet, Rev 2
60
Freescale Semiconductor
Chapter 4 Memory
4.6.4
FLASH Protection Register (FPROT and NVPROT)
During reset, the contents of the nonvolatile location NVPROT are copied from FLASH into FPROT. This
register may be read at any time.
•
If FPDIS = 0, then protection can be increased (in other words, a smaller value of FPS can be
written).
•
If FPDIS = 1, then writes do not change protection.
7
6
5
4
3
2
1
0
R
FPS7
FPS6
FPS5
FPS4
FPS3
FPS2
FPS1
FPDIS
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
W
Reset
This register is loaded from nonvolatile location NVPROT during reset.
1
Background commands can be used to change the contents of these bits in FPROT.
Figure 4-9. FLASH Protection Register (FPROT)
Table 4-11. FPROT Register Field Descriptions
Field
Description
7:1
FPS[7:1]
FLASH Protect Select Bits — When FPDIS = 0, this 7-bit field determines the ending address of unprotected
FLASH locations at the high address end of the FLASH. Protected FLASH locations cannot be erased or
programmed.
0
FLASH Protection Disable
FPDIS
0 FLASH block specified by FPS[7:1] is block protected (program and erase not allowed).
1 No FLASH block is protected.
4.6.5
FLASH Status Register (FSTAT)
Bits 3, 1, and 0 always read 0 and writes have no meaning or effect. The remaining five bits are status bits
that can be read at any time. Writes to these bits have special meanings that are discussed in the bit
descriptions.
7
6
5
4
3
2
1
0
R
W
FCCF
0
FBLANK
0
0
FCBEF
FPVIOL
FACCERR
Reset
1
1
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 4-10. FLASH Status Register (FSTAT)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
61
Chapter 4 Memory
Field
Table 4-12. FSTAT Register Field Descriptions
Description
7
FLASH Command Buffer Empty Flag — The FCBEF bit is used to launch commands. It also indicates that the
command buffer is empty so that a new command sequence can be executed when performing burst
programming. The FCBEF bit is cleared by writing a one to it or when a burst program command is transferred
to the array for programming. Only burst program commands can be buffered.
FCBEF
0 Command buffer is full (not ready for additional commands).
1 A new burst program command may be written to the command buffer.
6
FLASH Command Complete Flag — FCCF is set automatically when the command buffer is empty and no
command is being processed. FCCF is cleared automatically when a new command is started (by writing 1 to
FCBEF to register a command). Writing to FCCF has no meaning or effect.
0 Command in progress
FCCF
1 All commands complete
5
Protection Violation Flag — FPVIOL is set automatically when FCBEF is cleared to register a command that
attempts to erase or program a location in a protected block (the erroneous command is ignored). FPVIOL is
cleared by writing a 1 to FPVIOL.
FPVIOL
0 No protection violation.
1 An attempt was made to erase or program a protected location.
4
Access Error Flag — FACCERR is set automatically when the proper command sequence is not obeyed exactly
FACCERR (the erroneous command is ignored), if a program or erase operation is attempted before the FCDIV register has
been initialized, or if the MCU enters stop while a command was in progress. For a more detailed discussion of
the exact actions that are considered access errors, see Section 4.4.5, “Access Errors.” FACCERR is cleared by
writing a 1 to FACCERR. Writing a 0 to FACCERR has no meaning or effect.
0 No access error.
1 An access error has occurred.
2
FLASH Verified as All Blank (erased) Flag — FBLANK is set automatically at the conclusion of a blank check
command if the entire FLASH array was verified to be erased. FBLANK is cleared by clearing FCBEF to write a
new valid command. Writing to FBLANK has no meaning or effect.
FBLANK
0 After a blank check command is completed and FCCF = 1, FBLANK = 0 indicates the FLASH array is not
completely erased.
1 After a blank check command is completed and FCCF = 1, FBLANK = 1 indicates the FLASH array is
completely erased (all $FF).
MC9S08AW60 Data Sheet, Rev 2
62
Freescale Semiconductor
Chapter 4 Memory
4.6.6
FLASH Command Register (FCMD)
Only five command codes are recognized in normal user modes as shown in Table 4-14. Refer to
Section 4.4.3, “Program and Erase Command Execution” for a detailed discussion of FLASH
programming and erase operations.
7
6
5
4
3
2
1
0
R
W
0
0
0
0
0
0
0
0
FCMD7
FCMD6
FCMD5
FCMD4
FCMD3
FCMD2
FCMD1
FCMD0
Reset
0
0
0
0
0
0
0
0
Figure 4-11. FLASH Command Register (FCMD)
Table 4-13. FCMD Register Field Descriptions
Description
Field
FCMD[7:0] FLASH Command Bits — See Table 4-14
Table 4-14. FLASH Commands
Command
FCMD
Equate File Label
Blank check
$05
$20
$25
$40
$41
mBlank
Byte program
mByteProg
mBurstProg
mPageErase
mMassErase
Byte program — burst mode
Page erase (512 bytes/page)
Mass erase (all FLASH)
All other command codes are illegal and generate an access error.
It is not necessary to perform a blank check command after a mass erase operation. Only blank check is
required as part of the security unlocking mechanism.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
63
Chapter 4 Memory
MC9S08AW60 Data Sheet, Rev 2
64
Freescale Semiconductor
Chapter 5
Resets, Interrupts, and System Configuration
5.1
Introduction
This chapter discusses basic reset and interrupt mechanisms and the various sources of reset and interrupts
in the MC9S08AW60 Series. Some interrupt sources from peripheral modules are discussed in greater
detail within other chapters of this data manual. This chapter gathers basic information about all reset and
interrupt sources in one place for easy reference. A few reset and interrupt sources, including the computer
operating properly (COP) watchdog and real-time interrupt (RTI), are not part of on-chip peripheral
systems with their own sections but are part of the system control logic.
5.2
Features
Reset and interrupt features include:
•
Multiple sources of reset for flexible system configuration and reliable operation:
— Power-on detection (POR)
— Low voltage detection (LVD) with enable
— External RESET pin
— COP watchdog with enable and two timeout choices
— Illegal opcode
— Serial command from a background debug host
Reset status register (SRS) to indicate source of most recent reset
Separate interrupt vectors for each module (reduces polling overhead) (see Table 5-10)
•
•
5.3
MCU Reset
Resetting the MCU provides a way to start processing from a known set of initial conditions. During reset,
most control and status registers are forced to initial values and the program counter is loaded from the
reset vector ($FFFE:$FFFF). On-chip peripheral modules are disabled and I/O pins are initially configured
as general-purpose high-impedance inputs with pullup devices disabled. The I bit in the condition code
register (CCR) is set to block maskable interrupts so the user program has a chance to initialize the stack
pointer (SP) and system control settings. SP is forced to $00FF at reset.
The MC9S08AW60 Series has seven sources for reset:
•
•
•
Power-on reset (POR)
Low-voltage detect (LVD)
Computer operating properly (COP) timer
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
65
Chapter 5 Resets, Interrupts, and System Configuration
•
•
•
•
Illegal opcode detect
Background debug forced reset
The reset pin (RESET)
Clock generator loss of lock and loss of clock reset
Each of these sources, with the exception of the background debug forced reset, has an associated bit in
the system reset status register. Whenever the MCU enters reset, the internal clock generator (ICG) module
switches to self-clocked mode with the frequency of f
selected. The reset pin is driven low for 34
Self_reset
bus cycles where the internal bus frequency is half the ICG frequency. After the 34 bus cycles are
completed, the pin is released and will be pulled up by the internal pullup resistor, unless it is held low
externally. After the pin is released, it is sampled after another 38 bus cycles to determine whether the reset
pin is the cause of the MCU reset.
5.4
Computer Operating Properly (COP) Watchdog
The COP watchdog is intended to force a system reset when the application software fails to execute as
expected. To prevent a system reset from the COP timer (when it is enabled), application software must
reset the COP timer periodically. If the application program gets lost and fails to reset the COP before it
times out, a system reset is generated to force the system back to a known starting point. The COP
watchdog is enabled by the COPE bit in SOPT (see Section 5.9.4, “System Options Register (SOPT)” for
additional information). The COP timer is reset by writing any value to the address of SRS. This write does
not affect the data in the read-only SRS. Instead, the act of writing to this address is decoded and sends a
reset signal to the COP timer.
After any reset, the COP timer is enabled. This provides a reliable way to detect code that is not executing
as intended. If the COP watchdog is not used in an application, it can be disabled by clearing the COPE
bit in the write-once SOPT register. Also, the COPT bit can be used to choose one of two timeout periods
18
13
(2 or 2 cycles of the bus rate clock). Even if the application will use the reset default settings in COPE
and COPT, the user should write to write-once SOPT during reset initialization to lock in the settings. That
way, they cannot be changed accidentally if the application program gets lost.
The write to SRS that services (clears) the COP timer should not be placed in an interrupt service routine
(ISR) because the ISR could continue to be executed periodically even if the main application program
fails.
When the MCU is in active background mode, the COP timer is temporarily disabled.
5.5
Interrupts
Interrupts provide a way to save the current CPU status and registers, execute an interrupt service routine
(ISR), and then restore the CPU status so processing resumes where it left off before the interrupt. Other
than the software interrupt (SWI), which is a program instruction, interrupts are caused by hardware events
such as an edge on the IRQ pin or a timer-overflow event. The debug module can also generate an SWI
under certain circumstances.
If an event occurs in an enabled interrupt source, an associated read-only status flag will become set. The
CPU will not respond until and unless the local interrupt enable is a logic 1 to enable the interrupt. The
MC9S08AW60 Data Sheet, Rev 2
66
Freescale Semiconductor
Chapter 5 Resets, Interrupts, and System Configuration
I bit in the CCR is 0 to allow interrupts. The global interrupt mask (I bit) in the CCR is initially set after
reset which masks (prevents) all maskable interrupt sources. The user program initializes the stack pointer
and performs other system setup before clearing the I bit to allow the CPU to respond to interrupts.
When the CPU receives a qualified interrupt request, it completes the current instruction before responding
to the interrupt. The interrupt sequence obeys the same cycle-by-cycle sequence as the SWI instruction and
consists of:
•
•
•
•
Saving the CPU registers on the stack
Setting the I bit in the CCR to mask further interrupts
Fetching the interrupt vector for the highest-priority interrupt that is currently pending
Filling the instruction queue with the first three bytes of program information starting from the
address fetched from the interrupt vector locations
While the CPU is responding to the interrupt, the I bit is automatically set to avoid the possibility of another
interrupt interrupting the ISR itself (this is called nesting of interrupts). Normally, the I bit is restored to 0
when the CCR is restored from the value stacked on entry to the ISR. In rare cases, the I bit may be cleared
inside an ISR (after clearing the status flag that generated the interrupt) so that other interrupts can be
serviced without waiting for the first service routine to finish. This practice is not recommended for anyone
other than the most experienced programmers because it can lead to subtle program errors that are difficult
to debug.
The interrupt service routine ends with a return-from-interrupt (RTI) instruction which restores the CCR,
A, X, and PC registers to their pre-interrupt values by reading the previously saved information off the
stack.
NOTE
For compatibility with the M68HC08, the H register is not automatically
saved and restored. It is good programming practice to push H onto the stack
at the start of the interrupt service routine (ISR) and restore it immediately
before the RTI that is used to return from the ISR.
When two or more interrupts are pending when the I bit is cleared, the highest priority source is serviced
first (see Table 5-1).
5.5.1
Interrupt Stack Frame
Figure 5-1 shows the contents and organization of a stack frame. Before the interrupt, the stack pointer
(SP) points at the next available byte location on the stack. The current values of CPU registers are stored
on the stack starting with the low-order byte of the program counter (PCL) and ending with the CCR. After
stacking, the SP points at the next available location on the stack which is the address that is one less than
the address where the CCR was saved. The PC value that is stacked is the address of the instruction in the
main program that would have executed next if the interrupt had not occurred.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
67
Chapter 5 Resets, Interrupts, and System Configuration
TOWARD LOWER ADDRESSES
UNSTACKING
ORDER
7
0
SP AFTER
INTERRUPT STACKING
5
4
3
2
1
1
2
3
4
5
CONDITION CODE REGISTER
ACCUMULATOR
*
INDEX REGISTER (LOW BYTE X)
PROGRAM COUNTER HIGH
PROGRAM COUNTER LOW
SP BEFORE
THE INTERRUPT
STACKING
ORDER
TOWARD HIGHER ADDRESSES
* High byte (H) of index register is not automatically stacked.
Figure 5-1. Interrupt Stack Frame
When an RTI instruction is executed, these values are recovered from the stack in reverse order. As part of
the RTI sequence, the CPU fills the instruction pipeline by reading three bytes of program information,
starting from the PC address recovered from the stack.
The status flag causing the interrupt must be acknowledged (cleared) before returning from the ISR.
Typically, the flag should be cleared at the beginning of the ISR so that if another interrupt is generated by
this same source, it will be registered so it can be serviced after completion of the current ISR.
5.5.2
External Interrupt Request (IRQ) Pin
External interrupts are managed by the IRQSC status and control register. When the IRQ function is
enabled, synchronous logic monitors the pin for edge-only or edge-and-level events. When the MCU is in
stop mode and system clocks are shut down, a separate asynchronous path is used so the IRQ (if enabled)
can wake the MCU.
5.5.2.1
Pin Configuration Options
The IRQ pin enable (IRQPE) control bit in the IRQSC register must be 1 in order for the IRQ pin to act as
the interrupt request (IRQ) input. As an IRQ input, the user can choose the polarity of edges or levels
detected (IRQEDG), whether the pin detects edges-only or edges and levels (IRQMOD), and whether an
event causes an interrupt or only sets the IRQF flag which can be polled by software.
When the IRQ pin is configured to detect rising edges, an optional pulldown resistor is available rather than
a pullup resistor. BIH and BIL instructions may be used to detect the level on the IRQ pin when the pin is
configured to act as the IRQ input.
MC9S08AW60 Data Sheet, Rev 2
68
Freescale Semiconductor
Chapter 5 Resets, Interrupts, and System Configuration
NOTE
The voltage measured on the pulled up IRQ pin may be as low as
– 0.7 V. The internal gates connected to this pin are pulled all the way
V
DD
to V . All other pins with enabled pullup resistors will have an unloaded
DD
measurement of V
.
DD
5.5.2.2
Edge and Level Sensitivity
The IRQMOD control bit reconfigures the detection logic so it detects edge events and pin levels. In this
edge detection mode, the IRQF status flag becomes set when an edge is detected (when the IRQ pin
changes from the deasserted to the asserted level), but the flag is continuously set (and cannot be cleared)
as long as the IRQ pin remains at the asserted level.
5.5.3
Interrupt Vectors, Sources, and Local Masks
Table 5-1 provides a summary of all interrupt sources. Higher-priority sources are located toward the
bottom of the table. The high-order byte of the address for the interrupt service routine is located at the
first address in the vector address column, and the low-order byte of the address for the interrupt service
routine is located at the next higher address.
When an interrupt condition occurs, an associated flag bit becomes set. If the associated local interrupt
enable is 1, an interrupt request is sent to the CPU. Within the CPU, if the global interrupt mask (I bit in
the CCR) is 0, the CPU will finish the current instruction, stack the PCL, PCH, X, A, and CCR CPU
registers, set the I bit, and then fetch the interrupt vector for the highest priority pending interrupt.
Processing then continues in the interrupt service routine.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
69
Chapter 5 Resets, Interrupts, and System Configuration
Table 5-1. Vector Summary
Vector
Priority
Vector
Number
Address
(High/Low)
Vector Name Module
Source
Enable
Description
Lower
26
through
31
$FFC0/FFC1
through
$FFCA/FFCB
Unused Vector Space
(available for user program)
25
$FFCC/FFCD
Vrti
System
control
RTIF
RTIE
Real-time interrupt
24
23
22
21
$FFCE/FFCF
$FFD0/FFD1
$FFD2/FFD3
$FFD4/FFD5
Viic1
Vadc1
Vkeyboard 1
Vsci2tx
IIC1
ADC1
KBI1
SCI2
IICIF
COCO
KBF
TDRE
TC
IICIE
AIEN
KBIE
TIE
TCIE
IIC1
ADC1
KBI1 pins
SCI2 transmit
20
19
$FFD6/FFD7
$FFD8/FFD9
Vsci2rx
SCI2
SCI2
IDLE
RDRF
OR
NF
FE
PF
ILIE
RIE
ORIE
NFIE
FEIE
PFIE
SCI2 receive
SCI2 error
Vsci2err
18
17
16
$FFDA/FFDB
$FFDC/FFDD
$FFDE/FFDF
Vsci1tx
Vsci1rx
Vsci1err
SCI1
SCI1
SCI1
TDRE
TC
IDLE
TIE
TCIE
SCI1 transmit
SCI1 receive
SCI1 error
ILIE
RIE
ORIE
NFIE
FEIE
PFIE
RDRF
OR
NF
FE
PF
15
$FFE0/FFE1
Vspi1
SPI1
SPIF
MODF
SPTEF
SPIE
SPIE
SPTIE
SPI1
14
13
12
11
10
9
8
7
6
5
$FFE2/FFE3
$FFE4/FFE5
$FFE6/FFE7
$FFE8/FFE9
$FFEA/FFEB
$FFEC/FFED
$FFEE/FFEF
$FFF0/FFF1
$FFF2/FFF3
$FFF4/FFF5
$FFF6/FFF7
Vtpm2ovf
Vtpm2ch1
Vtpm2ch0
Vtpm1ovf
Vtpm1ch5
Vtpm1ch4
Vtpm1ch3
Vtpm1ch2
Vtpm1ch1
Vtpm1ch0
Vicg
TPM2
TPM2
TPM2
TPM1
TPM1
TPM1
TPM1
TPM1
TPM1
TPM1
ICG
TOF
CH1F
CH0F
TOF
CH5F
CH4F
CH3F
CH2F
CH1F
CH0F
TOIE
CH1IE
CH0IE
TOIE
CH5IE
CH4IE
CH3IE
CH2IE
CH1IE
TPM2 overflow
TPM2 channel 1
TPM2 channel 0
TPM1 overflow
TPM1 channel 5
TPM1 channel 4
TPM1 channel 3
TPM1 channel 2
TPM1 channel 1
TPM1 channel 0
ICG
CH0IE
4
ICGIF
LOLRE/LOCRE
(LOLS/LOCS)
3
$FFF8/FFF9
Vlvd
System
control
IRQ
LVDF
IRQF
LVDIE
Low-voltage detect
2
1
$FFFA/FFFB
$FFFC/FFFD
Virq
Vswi
IRQIE
—
IRQ pin
Software interrupt
Core
SWI
Instruction
0
$FFFE/FFFF
Vreset
System
control
COP
LVD
RESET pin
Illegal opcode
COPE
LVDRE
—
Watchdog timer
Low-voltage detect
External pin
Higher
—
Illegal opcode
MC9S08AW60 Data Sheet, Rev 2
70
Freescale Semiconductor
Chapter 5 Resets, Interrupts, and System Configuration
5.6
Low-Voltage Detect (LVD) System
The MC9S08AW60 Series includes a system to protect against low voltage conditions in order to protect
memory contents and control MCU system states during supply voltage variations. The system is
comprised of a power-on reset (POR) circuit and an LVD circuit with a user selectable trip voltage, either
high (V
) or low (V
). The LVD circuit is enabled when LVDE in SPMSC1 is high and the trip
LVDH
LVDL
voltage is selected by LVDV in SPMSC2. The LVD is disabled upon entering any of the stop modes unless
the LVDSE bit is set. If LVDSE and LVDE are both set, then the MCU cannot enter stop2, and the current
consumption in stop3 with the LVD enabled will be greater.
5.6.1
Power-On Reset Operation
When power is initially applied to the MCU, or when the supply voltage drops below the V
level, the
POR
POR circuit will cause a reset condition. As the supply voltage rises, the LVD circuit will hold the chip in
reset until the supply has risen above the V
following a POR.
level. Both the POR bit and the LVD bit in SRS are set
LVDL
5.6.2
LVD Reset Operation
The LVD can be configured to generate a reset upon detection of a low voltage condition by setting
LVDRE to 1. After an LVD reset has occurred, the LVD system will hold the MCU in reset until the supply
voltage has risen above the level determined by LVDV. The LVD bit in the SRS register is set following
either an LVD reset or POR.
5.6.3
LVD Interrupt Operation
When a low voltage condition is detected and the LVD circuit is configured for interrupt operation (LVDE
set, LVDIE set, and LVDRE clear), then LVDF will be set and an LVD interrupt will occur.
5.6.4
Low-Voltage Warning (LVW)
The LVD system has a low voltage warning flag to indicate to the user that the supply voltage is
approaching, the LVD voltage. The LVW does not have an interrupt associated with it. There are two user
selectable trip voltages for the LVW, one high (V
) and one low (V
). The trip voltage is selected
LVWH
LVWL
by LVWV in SPMSC2. Setting the LVW trip voltage equal to the LVD trip voltage is not recommended.
Typical use of the LVW would be to select V and V
.
LVDL
LVWH
5.7
Real-Time Interrupt (RTI)
The real-time interrupt function can be used to generate periodic interrupts. The RTI can accept two
sources of clocks, the 1-kHz internal clock or an external clock if available. The 1-kHz internal clock
source is completely independent of any bus clock source and is used only by the RTI module and, on some
MCUs, the COP watchdog. To use an external clock source, it must be available and active. The RTICLKS
bit in SRTISC is used to select the RTI clock source.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
71
Chapter 5 Resets, Interrupts, and System Configuration
Either RTI clock source can be used when the MCU is in run, wait or stop3 mode. When using the external
oscillator in stop3, it must be enabled in stop (OSCSTEN = 1) and configured for low bandwidth operation
(RANGE = 0). Only the internal 1-kHz clock source can be selected to wake the MCU from stop2 mode.
The SRTISC register includes a read-only status flag, a write-only acknowledge bit, and a 3-bit control
value (RTIS2:RTIS1:RTIS0) used to disable the clock source to the real-time interrupt or select one of
seven wakeup periods. The RTI has a local interrupt enable, RTIE, to allow masking of the real-time
interrupt. The RTI can be disabled by writing each bit of RTIS to zeroes, and no interrupts will be
generated. See Section 5.9.7, “System Real-Time Interrupt Status and Control Register (SRTISC),” for
detailed information about this register.
5.8
MCLK Output
The PTC2 pin is shared with the MCLK clock output. Setting the pin enable bit, MPE, causes the PTC2
pin to output a divided version of the internal MCU bus clock. The divide ratio is determined by the
MCSEL bits. When MPE is set, the PTC2 pin is forced to operate as an output pin regardless of the state
of the port data direction control bit for the pin. If the MCSEL bits are all 0s, the pin is driven low. The
slew rate and drive strength for the pin are controlled by PTCSE2 and PTCDS2, respectively. The
maximum clock output frequency is limited if slew rate control is enabled, see Appendix A, “Electrical
Characteristics and Timing Specifications,” for pin rise and fall times with slew rate enabled.
5.9
Reset, Interrupt, and System Control Registers and Control Bits
One 8-bit register in the direct page register space and eight 8-bit registers in the high-page register space
are related to reset and interrupt systems.
Refer to the direct-page register summary in Chapter 4, “Memory,” of this data sheet for the absolute
address assignments for all registers. This section refers to registers and control bits only by their names.
A Freescale-provided equate or header file is used to translate these names into the appropriate absolute
addresses.
Some control bits in the SOPT and SPMSC2 registers are related to modes of operation. Although brief
descriptions of these bits are provided here, the related functions are discussed in greater detail in
Chapter 3, “Modes of Operation.”
MC9S08AW60 Data Sheet, Rev 2
72
Freescale Semiconductor
Chapter 5 Resets, Interrupts, and System Configuration
5.9.1
Interrupt Pin Request Status and Control Register (IRQSC)
This direct page register includes two unimplemented bits which always read 0, four read/write bits, one
read-only status bit, and one write-only bit. These bits are used to configure the IRQ function, report status,
and acknowledge IRQ events.
7
6
5
4
3
2
1
0
R
W
0
0
IRQF
0
IRQEDG
IRQPE
IRQIE
IRQMOD
IRQACK
0
Reset
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 5-2. Interrupt Request Status and Control Register (IRQSC)
Table 5-2. IRQSC Register Field Descriptions
Description
Field
5
Interrupt Request (IRQ) Edge Select — This read/write control bit is used to select the polarity of edges or
levels on the IRQ pin that cause IRQF to be set. The IRQMOD control bit determines whether the IRQ pin is
sensitive to both edges and levels or only edges. When the IRQ pin is enabled as the IRQ input and is configured
to detect rising edges, the optional pullup resistor is re-configured as an optional pulldown resistor.
0 IRQ is falling edge or falling edge/low-level sensitive.
IRQEDG
1 IRQ is rising edge or rising edge/high-level sensitive.
4
IRQ Pin Enable — This read/write control bit enables the IRQ pin function. When this bit is set the IRQ pin can
be used as an interrupt request. Also, when this bit is set, either an internal pull-up or an internal pull-down
resistor is enabled depending on the state of the IRQEDG bit.
IRQPE
0 IRQ pin function is disabled.
1 IRQ pin function is enabled.
3
IRQ Flag — This read-only status bit indicates when an interrupt request event has occurred.
IRQF
0 No IRQ request.
1 IRQ event detected.
2
IRQ Acknowledge — This write-only bit is used to acknowledge interrupt request events (write 1 to clear IRQF).
Writing 0 has no meaning or effect. Reads always return logic 0. If edge-and-level detection is selected
(IRQMOD = 1), IRQF cannot be cleared while the IRQ pin remains at its asserted level.
IRQACK
1
IRQ Interrupt Enable — This read/write control bit determines whether IRQ events generate a hardware
interrupt request.
IRQIE
0 Hardware interrupt requests from IRQF disabled (use polling).
1 Hardware interrupt requested whenever IRQF = 1.
0
IRQ Detection Mode — This read/write control bit selects either edge-only detection or edge-and-level
IRQMOD detection. The IRQEDG control bit determines the polarity of edges and levels that are detected as interrupt
request events. See Section 5.5.2.2, “Edge and Level Sensitivity” for more details.
0 IRQ event on falling edges or rising edges only.
1 IRQ event on falling edges and low levels or on rising edges and high levels.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
73
Chapter 5 Resets, Interrupts, and System Configuration
5.9.2
System Reset Status Register (SRS)
This register includes seven read-only status flags to indicate the source of the most recent reset. When a
debug host forces reset by writing 1 to BDFR in the SBDFR register, none of the status bits in SRS will be
set. Writing any value to this register address clears the COP watchdog timer without affecting the contents
of this register. The reset state of these bits depends on what caused the MCU to reset.
7
6
5
4
3
2
1
0
R
W
POR
PIN
COP
ILOP
0
ICG
LVD
0
Writing any value to SIMRS address clears COP watchdog timer.
POR
LVR:
1
U
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
(1)
(1)
(1)
(1)
Any other
reset:
U = Unaffected by reset
1
Any of these reset sources that are active at the time of reset will cause the corresponding bit(s) to be set; bits corresponding
to sources that are not active at the time of reset will be cleared.
Figure 5-3. System Reset Status (SRS)
Table 5-3. SRS Register Field Descriptions
Field
Description
7
POR
Power-On Reset — Reset was caused by the power-on detection logic. Because the internal supply voltage was
ramping up at the time, the low-voltage reset (LVR) status bit is also set to indicate that the reset occurred while
the internal supply was below the LVR threshold.
0 Reset not caused by POR.
1 POR caused reset.
6
PIN
External Reset Pin — Reset was caused by an active-low level on the external reset pin.
0 Reset not caused by external reset pin.
1 Reset came from external reset pin.
5
COP
Computer Operating Properly (COP) Watchdog — Reset was caused by the COP watchdog timer timing out.
This reset source may be blocked by COPE = 0.
0 Reset not caused by COP timeout.
1 Reset caused by COP timeout.
4
Illegal Opcode — Reset was caused by an attempt to execute an unimplemented or illegal opcode. The STOP
instruction is considered illegal if stop is disabled by STOPE = 0 in the SOPT register. The BGND instruction is
considered illegal if active background mode is disabled by ENBDM = 0 in the BDCSC register.
0 Reset not caused by an illegal opcode.
ILOP
1 Reset caused by an illegal opcode.
MC9S08AW60 Data Sheet, Rev 2
74
Freescale Semiconductor
Chapter 5 Resets, Interrupts, and System Configuration
Table 5-3. SRS Register Field Descriptions (continued)
Field
Description
2
ICG
Internal Clock Generation Module Reset — Reset was caused by an ICG module reset.
0 Reset not caused by ICG module.
1 Reset caused by ICG module.
1
LVD
Low Voltage Detect — If the LVDRE and LVDSE bits are set and the supply drops below the LVD trip voltage,
an LVD reset will occur. This bit is also set by POR.
0 Reset not caused by LVD trip or POR.
1 Reset caused by LVD trip or POR.
5.9.3
System Background Debug Force Reset Register (SBDFR)
This register contains a single write-only control bit. A serial background command such as
WRITE_BYTE must be used to write to SBDFR. Attempts to write this register from a user program are
ignored. Reads always return $00.
7
6
5
4
3
2
1
0
R
W
0
0
0
0
0
0
0
0
BDFR1
0
Reset
0
0
0
0
0
0
0
= Unimplemented or Reserved
1
BDFR is writable only through serial background debug commands, not from user programs.
Figure 5-4. System Background Debug Force Reset Register (SBDFR)
Table 5-4. SBDFR Register Field Descriptions
Description
Field
0
Background Debug Force Reset — A serial background command such as WRITE_BYTE may be used to
allow an external debug host to force a target system reset. Writing logic 1 to this bit forces an MCU reset. This
bit cannot be written from a user program.
BDFR
5.9.4
System Options Register (SOPT)
This register may be read at any time. Bits 3 and 2 are unimplemented and always read 0. This is a
write-once register so only the first write after reset is honored. Any subsequent attempt to write to SOPT
(intentionally or unintentionally) is ignored to avoid accidental changes to these sensitive settings. SOPT
should be written during the user’s reset initialization program to set the desired controls even if the desired
settings are the same as the reset settings.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
75
Chapter 5 Resets, Interrupts, and System Configuration
7
6
5
4
3
2
1
0
R
W
0
0
COPE
COPT
STOPE
Reset
1
1
0
1
0
0
1
1
= Unimplemented or Reserved
Figure 5-5. System Options Register (SOPT)
Table 5-5. SOPT Register Field Descriptions
Description
Field
7
COP Watchdog Enable — This write-once bit defaults to 1 after reset.
0 COP watchdog timer disabled.
COPE
1 COP watchdog timer enabled (force reset on timeout).
6
COP Watchdog Timeout — This write-once bit defaults to 1 after reset.
0 Short timeout period selected (213 cycles of BUSCLK).
1 Long timeout period selected (218 cycles of BUSCLK).
COPT
5
Stop Mode Enable — This write-once bit defaults to 0 after reset, which disables stop mode. If stop mode is
disabled and a user program attempts to execute a STOP instruction, an illegal opcode reset is forced.
0 Stop mode disabled.
STOPE
1 Stop mode enabled.
5.9.5
System MCLK Control Register (SMCLK)
This register is used to control the MCLK clock output.
7
6
5
4
3
2
1
0
R
W
0
0
0
0
MPE
MCSEL
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 5-6. System MCLK Control Register (SMCLK)
Table 5-6. SMCLK Register Field Descriptions
Description
Field
4
MPE
MCLK Pin Enable — This bit is used to enable the MCLK function.
0 MCLK output disabled.
1 MCLK output enabled on PTC2 pin.
2:0
MCSEL
MCLK Divide Select — These bits are used to select the divide ratio for the MCLK output according to the
formula below when the MCSEL bits are not equal to all zeroes. In the case that the MCSEL bits are all zero and
MPE is set, the pin is driven low. See Equation 5-1.
MCLK frequency = Bus Clock frequency ÷ (2 * MCSEL)
Eqn. 5-1
MC9S08AW60 Data Sheet, Rev 2
76
Freescale Semiconductor
Chapter 5 Resets, Interrupts, and System Configuration
5.9.6
System Device Identification Register (SDIDH, SDIDL)
This read-only register is included so host development systems can identify the HCS08 derivative. This
allows the development software to recognize where specific memory blocks, registers, and control bits
are located in a target MCU.
7
6
5
4
3
2
1
0
R
W
ID11
ID10
ID9
ID8
Reset
0
0
0
0
—
—
—
—
= Unimplemented or Reserved
Figure 5-7. System Device Identification Register — High (SDIDH)
Table 5-7. SDIDH Register Field Descriptions
Description
Field
7:4
Bits 7:4 are reserved. Reading these bits will result in an indeterminate value; writes have no effect.
Reserved
3:0
Part Identification Number — Each derivative in the HCS08 family has a unique identification number. The
ID[11:8]
MC9S08AW60 Series is hard coded to the value $008. See also ID bits in Table 5-8.
7
6
5
4
3
2
1
0
R
W
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
Reset
0
0
0
0
1
0
0
0
= Unimplemented or Reserved
Figure 5-8. System Device Identification Register — Low (SDIDL)
Table 5-8. SDIDL Register Field Descriptions
Description
Field
7:0
Part Identification Number — Each derivative in the HCS08 family has a unique identification number. The
ID[7:0]
MC9S08AW60 Series is hard coded to the value $008. See also ID bits in Table 5-7.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
77
Chapter 5 Resets, Interrupts, and System Configuration
5.9.7
System Real-Time Interrupt Status and Control Register (SRTISC)
This register contains one read-only status flag, one write-only acknowledge bit, three read/write delay
selects, and three unimplemented bits, which always read 0.
7
6
5
4
3
2
1
0
R
W
RTIF
0
0
RTICLKS
RTIE
RTIS2
RTIS1
RTIS0
RTIACK
0
Reset
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 5-9. System RTI Status and Control Register (SRTISC)
Table 5-9. SRTISC Register Field Descriptions
Description
Field
7
RTIF
Real-Time Interrupt Flag — This read-only status bit indicates the periodic wakeup timer has timed out.
0 Periodic wakeup timer not timed out.
1 Periodic wakeup timer timed out.
6
Real-Time Interrupt Acknowledge — This write-only bit is used to acknowledge real-time interrupt request
RTIACK
(write 1 to clear RTIF). Writing 0 has no meaning or effect. Reads always return logic 0.
5
Real-Time Interrupt Clock Select — This read/write bit selects the clock source for the real-time interrupt.
RTICLKS 0 Real-time interrupt request clock source is internal 1-kHz oscillator.
1 Real-time interrupt request clock source is external clock.
4
Real-Time Interrupt Enable — This read-write bit enables real-time interrupts.
0 Real-time interrupts disabled.
RTIE
1 Real-time interrupts enabled.
2:0
Real-Time Interrupt Delay Selects — These read/write bits select the wakeup delay for the RTI. The clock
RTIS[2:0] source for the real-time interrupt is a self-clocked source which oscillates at about 1 kHz, is independent of other
MCU clock sources. Using external clock source the delays will be crystal frequency divided by value in
RTIS2:RTIS1:RTIS0. See Table 5-10.
Table 5-10. Real-Time Interrupt Frequency
Using External Clock Source Delay
RTIS2:RTIS1:RTIS0
1-kHz Clock Source Delay1
(Crystal Frequency)
0:0:0
0:0:1
0:1:0
0:1:1
1:0:0
1:0:1
1:1:0
1:1:1
Disable periodic wakeup timer
Disable periodic wakeup timer
divide by 256
8 ms
32 ms
divide by 1024
64 ms
divide by 2048
128 ms
256 ms
512 ms
1.024 s
divide by 4096
divide by 8192
divide by 16384
divide by 32768
1
Normal values are shown in this column based on fRTI = 1 kHz. See Appendix A, “Electrical Characteristics and Timing
Specifications,” fRTI for the tolerance on these values.
MC9S08AW60 Data Sheet, Rev 2
78
Freescale Semiconductor
Chapter 5 Resets, Interrupts, and System Configuration
5.9.8
System Power Management Status and Control 1 Register (SPMSC1)
1
7
6
5
4
3
2
1
0
R
LVDF
0
LVDIE
LVDRE(2)
LVDSE(2)
LVDE(2)
BGBE
W
LVDACK
0
Reset
0
0
1
1
1
0
0
= Unimplemented or Reserved
1
2
Bit 1 is a reserved bit that must always be written to 0.
This bit can be written only one time after reset. Additional writes are ignored.
Figure 5-10. System Power Management Status and Control 1 Register (SPMSC1)
Table 5-11. SPMSC1 Register Field Descriptions
Description
Field
7
Low-Voltage Detect Flag — Provided LVDE = 1, this read-only status bit indicates a low-voltage detect event.
LVDF
6
Low-Voltage Detect Acknowledge — This write-only bit is used to acknowledge low voltage detection errors
LVDACK
(write 1 to clear LVDF). Reads always return 0.
5
Low-Voltage Detect Interrupt Enable — This read/write bit enables hardware interrupt requests for LVDF.
0 Hardware interrupt disabled (use polling).
LVDIE
1 Request a hardware interrupt when LVDF = 1.
4
Low-Voltage Detect Reset Enable — This read/write bit enables LVDF events to generate a hardware reset
(provided LVDE = 1).
LVDRE
0 LVDF does not generate hardware resets.
1 Force an MCU reset when LVDF = 1.
3
Low-Voltage Detect Stop Enable — Provided LVDE = 1, this read/write bit determines whether the low-voltage
detect function operates when the MCU is in stop mode.
LVDSE
0 Low-voltage detect disabled during stop mode.
1 Low-voltage detect enabled during stop mode.
2
Low-Voltage Detect Enable — This read/write bit enables low-voltage detect logic and qualifies the operation
LVDE
of other bits in this register.
0 LVD logic disabled.
1 LVD logic enabled.
0
Bandgap Buffer Enable — The BGBE bit is used to enable an internal buffer for the bandgap voltage reference
for use by the ADC module on one of its internal channels.
0 Bandgap buffer disabled.
BGBE
1 Bandgap buffer enabled.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
79
Chapter 5 Resets, Interrupts, and System Configuration
5.9.9
System Power Management Status and Control 2 Register (SPMSC2)
This register is used to report the status of the low voltage warning function, and to configure the stop mode
behavior of the MCU.
7
6
5
4
3
2
1
0
R
LVWF
0
PPDF
0
LVDV
LVWV
PPDC1
W
LVWACK
0
PPDACK
0
0(2)
0(2)
0(2)
0
U
U
0
U
U
0
0
0
0
0
0
0
0
0
Power-on
reset:
0
0
0
0
LVD
reset:
Any other
reset:
= Unimplemented or Reserved
U = Unaffected by reset
1
2
This bit can be written only one time after reset. Additional writes are ignored.
LVWF will be set in the case when VSupply transitions below the trip point or after reset and VSupply is already below VLVW
.
Figure 5-11. System Power Management Status and Control 2 Register (SPMSC2)
Table 5-12. SPMSC2 Register Field Descriptions
Description
Field
7
Low-Voltage Warning Flag — The LVWF bit indicates the low voltage warning status.
0 Low voltage warning not present.
LVWF
1 Low voltage warning is present or was present.
6
Low-Voltage Warning Acknowledge — The LVWACK bit is the low-voltage warning acknowledge.
LVWACK
Writing a 1 to LVWACK clears LVWF to a 0 if a low voltage warning is not present.
5
Low-Voltage Detect Voltage Select — The LVDV bit selects the LVD trip point voltage (VLVD).
0 Low trip point selected (VLVD = VLVDL).
LVDV
1 High trip point selected (VLVD = VLVDH).
4
Low-Voltage Warning Voltage Select — The LVWV bit selects the LVW trip point voltage (VLVW).
0 Low trip point selected (VLVW = VLVWL).
LVWV
1 High trip point selected (VLVW = VLVWH).
3
Partial Power Down Flag — The PPDF bit indicates that the MCU has exited the stop2 mode.
PPDF
0 Not stop2 mode recovery.
1 Stop2 mode recovery.
2
Partial Power Down Acknowledge — Writing a 1 to PPDACK clears the PPDF bit.
PPDACK
0
Partial Power Down Control — The write-once PPDC bit controls whether stop2 or stop3 mode is selected.
0 Stop3 mode enabled.
PPDC
1 Stop2, partial power down, mode enabled.
MC9S08AW60 Data Sheet, Rev 2
80
Freescale Semiconductor
Chapter 6
Parallel Input/Output
6.1
Introduction
This chapter explains software controls related to parallel input/output (I/O). The MC9S08AW60 has
seven I/O ports which include a total of 54 general-purpose I/O pins. See Chapter 2, “Pins and
Connections” for more information about the logic and hardware aspects of these pins.
Many of these pins are shared with on-chip peripherals such as timer systems, communication systems, or
keyboard interrupts. When these other modules are not controlling the port pins, they revert to
general-purpose I/O control.
Pins that are not used in the application must be terminated. This prevents excess current caused by floating
inputs and enhances immunity during noise or transient events. Termination methods include:
•
•
Configuring unused pins as outputs driving high or low
Configuring unused pins as inputs and using internal or external pullups
Never connect unused pins to V or V .
DD
SS
Table 6-1. KBI and Parallel I/O Interaction
PTxPEn
(Pull Enable)
PTxDDn
KBIPEn
KBEDGn
Pullup
Pulldown
(Data Direction) (KBI Pin Enable) (KBI Edge Select)
0
0
0
1
x
x
x
0
0
0
1
1
1
x1
x
disabled
enabled
disabled
enabled
disabled
disabled
disabled
disabled
disabled
disabled
enabled
disabled
1
x
x
1
0
1
x
1
0
1
x = Don’t care
6.2
Features
Parallel I/O and Pin Control features, depending on package choice, include:
•
•
•
A total of 54 general-purpose I/O pins in seven ports
Hysteresis input buffers
Software-controlled pullups on each input pin
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
81
Chapter 6 Parallel Input/Output
•
•
•
•
•
•
•
•
Software-controlled slew rate output buffers
Eight port A pins
Eight port B pins shared with ADC1
Seven port C pins shared with SCI2, IIC1, and MCLK
Eight port D pins shared with ADC1, KBI1, and TPM1 and TPM2 external clock inputs
Eight port E pins shared with SCI1, TPM1, and SPI1
Eight port F pins shared with TPM1 and TPM2
Seven port G pins shared with XTAL, EXTAL, and KBI1
6.3
Pin Descriptions
The MC9S08AW60 Series has a total of 54 parallel I/O pins in seven ports (PTA–PTG). Not all pins are
bonded out in all packages. Consult the pin assignment in Chapter 2, “Pins and Connections,” for available
parallel I/O pins. All of these pins are available for general-purpose I/O when they are not used by other
on-chip peripheral systems.
After reset, the shared peripheral functions are disabled so that the pins are controlled by the parallel I/O.
All of the parallel I/O are configured as inputs (PTxDDn = 0). The pin control functions for each pin are
configured as follows: slew rate control enabled (PTxSEn = 1), low drive strength selected (PTxDSn = 0),
and internal pullups disabled (PTxPEn = 0).
The following paragraphs discuss each port and the software controls that determine each pin’s use.
6.3.1
Port A
Port A
Bit 7
MCU Pin: PTA7
6
5
4
3
2
1
Bit 0
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
Figure 6-1. Port A Pin Names
Port A pins are general-purpose I/O pins. Parallel I/O function is controlled by the port A data (PTAD) and
data direction (PTADD) registers which are located in page zero register space. The pin control registers,
pullup enable (PTAPE), slew rate control (PTASE), and drive strength select (PTADS) are located in the
high page registers. Refer to Section 6.4, “Parallel I/O Control” for more information about
general-purpose I/O control and Section 6.5, “Pin Control” for more information about pin control.
6.3.2
Port B
Port B
Bit 7
6
5
4
3
2
1
Bit 0
PTB7/
AD1P7
PTB6/
AD1P6
PTB5/
AD1P5
PTB4/
AD1P4
PTB3/
AD1P3
PTB2/
AD1P2
PTB1/
AD1P1
PTB0/
AD1P0
MCU Pin:
Figure 6-2. Port B Pin Names
MC9S08AW60 Data Sheet, Rev 2
82
Freescale Semiconductor
Chapter 6 Parallel Input/Output
Port B pins are general-purpose I/O pins. Parallel I/O function is controlled by the port B data (PTBD) and
data direction (PTBDD) registers which are located in page zero register space. The pin control registers,
pullup enable (PTBPE), slew rate control (PTBSE), and drive strength select (PTBDS) are located in the
high page registers. Refer to Section 6.4, “Parallel I/O Control” for more information about
general-purpose I/O control and Section 6.5, “Pin Control” for more information about pin control.
Port B general-purpose I/O are shared with the ADC. Any pin enabled as an ADC input will have the
general-purpose I/O function disabled. Refer to Chapter 14, “Analog-to-Digital Converter
(S08ADC10V1)” for more information about using port B as analog inputs.
6.3.3
Port C
Port C
Bit 7
6
5
3
3
2
1
Bit 0
PTC5/
RxD2
PTC3/
TxD2
PTC2/
MCLK
PTC1/
SDA1
PTC0/
SCL1
MCU Pin:
PTC6
PTC4
Figure 6-3. Port C Pin Names
Port C pins are general-purpose I/O pins. Parallel I/O function is controlled by the port C data (PTCD) and
data direction (PTCDD) registers which are located in page zero register space. The pin control registers,
pullup enable (PTCPE), slew rate control (PTCSE), and drive strength select (PTCDS) are located in the
high page registers. Refer to Section 6.4, “Parallel I/O Control” for more information about
general-purpose I/O control and Section 6.5, “Pin Control” for more information about pin control.
Port C general-purpose I/O is shared with SCI2, IIC, and MCLK. When any of these shared functions is
enabled, the direction, input or output, is controlled by the shared function and not by the data direction
register of the parallel I/O port. Also, for pins which are configured as outputs by the shared function, the
output data is controlled by the shared function and not by the port data register.
Refer to Chapter 11, “Serial Communications Interface (S08SCIV2)” for more information about using
port C pins as SCI pins.
Refer to Chapter 13, “Inter-Integrated Circuit (S08IICV1)” for more information about using port C pins
as IIC pins.
Refer to Chapter 5, “Resets, Interrupts, and System Configuration” for more information about using
PTC2 as the MCLK pin.
6.3.4
Port D
Port D
Bit 7
6
5
4
3
2
1
Bit 0
PTD7/
AD1P15/
KBI1P7
PTD6/
AD1P14/
TPM1CLK
PTD4/
AD1P12/
TPM2CLK
PTD3/
AD1P11/
KBI1P6
PTD2/
AD1P10/
KBI1P5
PTD5/
AD1P13/
PTD1/
AD1P9
PTD0/
AD1P8
MCU Pin:
Figure 6-4. Port D Pin Names
Port D pins are general-purpose I/O pins. Parallel I/O function is controlled by the port D data (PTDD) and
data direction (PTDDD) registers which are located in page zero register space. The pin control registers,
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
83
Chapter 6 Parallel Input/Output
pullup enable (PTDPE), slew rate control (PTDSE), and drive strength select (PTDDS) are located in the
high page registers. Refer to Section 6.4, “Parallel I/O Control” for more information about
general-purpose I/O control and Section 6.5, “Pin Control” for more information about pin control.
Port D general-purpose I/O are shared with the ADC, KBI, and TPM1 and TPM2 external clock inputs.
When any of these shared functions is enabled, the direction, input or output, is controlled by the shared
function and not by the data direction register of the parallel I/O port. When a pin is shared with both the
ADC and a digital peripheral function, the ADC has higher priority. For example, in the case that both the
ADC and the KBI are configured to use PTD7 then the pin is controlled by the ADC module.
Refer to Chapter 10, “Timer/PWM (S08TPMV2)” for more information about using port D pins as TPM
external clock inputs.
Refer to Chapter 14, “Analog-to-Digital Converter (S08ADC10V1)” for more information about using
port D pins as analog inputs.
Refer to Chapter 9, “Keyboard Interrupt (S08KBIV1)” for more information about using port D pins as
keyboard inputs.
6.3.5
Port E
Port E
Bit 7
6
5
4
3
2
1
Bit 0
PTE7/
SPSCK1
PTE6/
MOSI1
PTE5/
MISO1
PTE4/
SS1
PTE3/ PTE2/
TPM1CH1 TPM1CH0
PTE1/
RxD1
PTE0/
TxD1
MCU Pin:
Figure 6-5. Port E Pin Names
Port E pins are general-purpose I/O pins. Parallel I/O function is controlled by the port E data (PTED) and
data direction (PTEDD) registers which are located in page zero register space. The pin control registers,
pullup enable (PTEPE), slew rate control (PTESE), and drive strength select (PTEDS) are located in the
high page registers. Refer to Section 6.4, “Parallel I/O Control” for more information about
general-purpose I/O control and Section 6.5, “Pin Control” for more information about pin control.
Port E general-purpose I/O is shared with SCI1, SPI, and TPM1 timer channels. When any of these shared
functions is enabled, the direction, input or output, is controlled by the shared function and not by the data
direction register of the parallel I/O port. Also, for pins which are configured as outputs by the shared
function, the output data is controlled by the shared function and not by the port data register.
Refer to Chapter 11, “Serial Communications Interface (S08SCIV2)” for more information about using
port E pins as SCI pins.
Refer to Chapter 12, “Serial Peripheral Interface (S08SPIV3)” for more information about using port E
pins as SPI pins.
Refer to Chapter 10, “Timer/PWM (S08TPMV2)” for more information about using port E pins as TPM
channel pins.
MC9S08AW60 Data Sheet, Rev 2
84
Freescale Semiconductor
Chapter 6 Parallel Input/Output
6.3.6
Port F
Port F
Bit 7
6
5
4
3
2
1
Bit 0
PTF5/
PTF4/
PTF3/
PTF2/
TPM2CH1 TPM2CH0 TPM1CH5 TPM1CH4 TPM1CH3 TPM1CH2
PTF1/
PTF0/
MCU Pin:
PTF7
PTF6
Figure 6-6. Port F Pin Names
Port F pins are general-purpose I/O pins. Parallel I/O function is controlled by the port F data (PTFD) and
data direction (PTFDD) registers which are located in page zero register space. The pin control registers,
pullup enable (PTFPE), slew rate control (PTFSE), and drive strength select (PTFDS) are located in the
high page registers. Refer to Section 6.4, “Parallel I/O Control” for more information about
general-purpose I/O control and Section 6.5, “Pin Control” for more information about pin control.
Port F general-purpose I/O is shared with TPM1 and TPM2 timer channels. When any of these shared
functions is enabled, the direction, input or output, is controlled by the shared function and not by the data
direction register of the parallel I/O port. Also, for pins which are configured as outputs by the shared
function, the output data is controlled by the shared function and not by the port data register.
Refer to Chapter 10, “Timer/PWM (S08TPMV2)” for more information about using port F pins as TPM
channel pins.
6.3.7
Port G
Port G
Bit 7
6
5
4
3
2
1
Bit 0
PTG6/
EXTAL
PTG5/
XTAL
PTG4/
KBI1P4
PTG3/
KBI1P3
PTG2/
KBI1P2
PTG1/
KBI1P1
PTG0/
KBI1P0
MCU Pin:
Figure 6-7. Port G Pin Names
Port G pins are general-purpose I/O pins. Parallel I/O function is controlled by the port G data (PTGD) and
data direction (PTGDD) registers which are located in page zero register space. The pin control registers,
pullup enable (PTGPE), slew rate control (PTGSE), and drive strength select (PTGDS) are located in the
high page registers. Refer to Section 6.4, “Parallel I/O Control” for more information about
general-purpose I/O control and Section 6.5, “Pin Control” for more information about pin control.
Port G general-purpose I/O is shared with KBI, XTAL, and EXTAL. When a pin is enabled as a KBI input,
the pin functions as an input regardless of the state of the associated PTG data direction register bit. When
the external oscillator is enabled, PTG5 and PTG6 function as oscillator pins. In this case the associated
parallel I/O and pin control registers have no control of the pins.
Refer to Chapter 8, “Internal Clock Generator (S08ICGV4)” for more information about using port G pins
as XTAL and EXTAL pins.
Refer to Chapter 9, “Keyboard Interrupt (S08KBIV1)” for more information about using port G pins as
keyboard inputs.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
85
Chapter 6 Parallel Input/Output
6.4
Parallel I/O Control
Reading and writing of parallel I/O is done through the port data registers. The direction, input or output,
is controlled through the port data direction registers. The parallel I/O port function for an individual pin
is illustrated in the block diagram below.
PTxDDn
Output Enable
D
Q
PTxDn
Output Data
D
Q
1
0
Port Read
Data
Input Data
Synchronizer
BUSCLK
Figure 6-8. Parallel I/O Block Diagram
The data direction control bits determine whether the pin output driver is enabled, and they control what
is read for port data register reads. Each port pin has a data direction register bit. When PTxDDn = 0, the
corresponding pin is an input and reads of PTxD return the pin value. When PTxDDn = 1, the
corresponding pin is an output and reads of PTxD return the last value written to the port data register.
When a peripheral module or system function is in control of a port pin, the data direction register bit still
controls what is returned for reads of the port data register, even though the peripheral system has
overriding control of the actual pin direction.
When a shared analog function is enabled for a pin, all digital pin functions are disabled. A read of the port
data register returns a value of 0 for any bits which have shared analog functions enabled. In general,
whenever a pin is shared with both an alternate digital function and an analog function, the analog function
has priority such that if both the digital and analog functions are enabled, the analog function controls the
pin.
It is a good programming practice to write to the port data register before changing the direction of a port
pin to become an output. This ensures that the pin will not be driven momentarily with an old data value
that happened to be in the port data register.
MC9S08AW60 Data Sheet, Rev 2
86
Freescale Semiconductor
Chapter 6 Parallel Input/Output
6.5
Pin Control
The pin control registers are located in the high page register block of the memory. These registers are used
to control pullups, slew rate, and drive strength for the I/O pins. The pin control registers operate
independently of the parallel I/O registers.
6.5.1
Internal Pullup Enable
An internal pullup device can be enabled for each port pin by setting the corresponding bit in one of the
pullup enable registers (PTxPEn). The pullup device is disabled if the pin is configured as an output by the
parallel I/O control logic or any shared peripheral function regardless of the state of the corresponding
pullup enable register bit. The pullup device is also disabled if the pin is controlled by an analog function.
6.5.2
Output Slew Rate Control Enable
Slew rate control can be enabled for each port pin by setting the corresponding bit in one of the slew rate
control registers (PTxSEn). When enabled, slew control limits the rate at which an output can transition in
order to reduce EMC emissions. Slew rate control has no effect on pins which are configured as inputs.
6.5.3
Output Drive Strength Select
An output pin can be selected to have high output drive strength by setting the corresponding bit in one of
the drive strength select registers (PTxDSn). When high drive is selected a pin is capable of sourcing and
sinking greater current. Even though every I/O pin can be selected as high drive, the user must ensure that
the total current source and sink limits for the chip are not exceeded. Drive strength selection is intended
to affect the DC behavior of I/O pins. However, the AC behavior is also affected. High drive allows a pin
to drive a greater load with the same switching speed as a low drive enabled pin into a smaller load.
Because of this the EMC emissions may be affected by enabling pins as high drive.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
87
Chapter 6 Parallel Input/Output
6.6
Pin Behavior in Stop Modes
Depending on the stop mode, I/O functions differently as the result of executing a STOP instruction. An
explanation of I/O behavior for the various stop modes follows:
•
Stop2 mode is a partial power-down mode, whereby I/O latches are maintained in their state as
before the STOP instruction was executed. CPU register status and the state of I/O registers should
be saved in RAM before the STOP instruction is executed to place the MCU in stop2 mode. Upon
recovery from stop2 mode, before accessing any I/O, the user should examine the state of the PPDF
bit in the SPMSC2 register. If the PPDF bit is 0, I/O must be initialized as if a power on reset had
occurred. If the PPDF bit is 1, I/O data previously stored in RAM, before the STOP instruction was
executed, peripherals may require being initialized and restored to their pre-stop condition. The
user must then write a 1 to the PPDACK bit in the SPMSC2 register. Access to I/O is now permitted
again in the user’s application program.
•
In stop3 mode, all I/O is maintained because internal logic circuity stays powered up. Upon
recovery, normal I/O function is available to the user.
6.7
Parallel I/O and Pin Control Registers
This section provides information about the registers associated with the parallel I/O ports and pin control
functions. These parallel I/O registers are located in page zero of the memory map and the pin control
registers are located in the high page register section of memory.
Refer to tables in Chapter 4, “Memory,” for the absolute address assignments for all parallel I/O and pin
control registers. This section refers to registers and control bits only by their names. A Freescale-provided
equate or header file normally is used to translate these names into the appropriate absolute addresses.
6.7.1
Port A I/O Registers (PTAD and PTADD)
Port A parallel I/O function is controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTAD7
PTAD6
PTAD5
PTAD4
PTAD3
PTAD2
PTAD1
PTAD0
Reset
0
0
0
0
0
0
0
0
Figure 6-9. Port A Data Register (PTAD)
Table 6-2. PTAD Register Field Descriptions
Description
Field
7:0
Port A Data Register Bits — For port A pins that are inputs, reads return the logic level on the pin. For port A
PTAD[7:0] pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port A pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTAD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures
all port pins as high-impedance inputs with pullups disabled.
MC9S08AW60 Data Sheet, Rev 2
88
Freescale Semiconductor
Chapter 6 Parallel Input/Output
7
6
5
4
3
2
1
0
R
W
PTADD7
PTADD6
PTADD5
PTADD4
PTADD3
PTADD2
PTADD1
PTADD0
Reset
0
0
0
0
0
0
0
0
Figure 6-10. Data Direction for Port A Register (PTADD)
Table 6-3. PTADD Register Field Descriptions
Description
Field
7:0
Data Direction for Port A Bits — These read/write bits control the direction of port A pins and what is read for
PTADD[7:0] PTAD reads.
0 Input (output driver disabled) and reads return the pin value.
1 Output driver enabled for port A bit n and PTAD reads return the contents of PTADn.
6.7.2
Port A Pin Control Registers (PTAPE, PTASE, PTADS)
In addition to the I/O control, port A pins are controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTAPE7
PTAPE6
PTAPE5
PTAPE4
PTAPE3
PTAPE2
PTAPE1
PTAPE0
Reset
0
0
0
0
0
0
0
0
Figure 6-11. Internal Pullup Enable for Port A (PTAPE)
Table 6-4. PTADD Register Field Descriptions
Description
Field
[7:0]
Internal Pullup Enable for Port A Bits — Each of these control bits determines if the internal pullup device is
PTAPE[7:0] enabled for the associated PTA pin. For port A pins that are configured as outputs, these bits have no effect and
the internal pullup devices are disabled.
0 Internal pullup device disabled for port A bit n.
1 Internal pullup device enabled for port A bit n.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
89
Chapter 6 Parallel Input/Output
7
6
5
4
3
2
1
0
R
PTASE7
0
PTASE6
0
PTASE5
PTASE4
PTASE3
PTASE2
PTASE1
PTASE0
W
Reset
0
0
0
0
0
0
Figure 6-12. Output Slew Rate Control Enable for Port A (PTASE)
Table 6-5. PTASE Register Field Descriptions
Description
Field
7:0
Output Slew Rate Control Enable for Port A Bits — Each of these control bits determine whether output slew
PTASE[7:0] rate control is enabled for the associated PTA pin. For port A pins that are configured as inputs, these bits have
no effect.
0 Output slew rate control disabled for port A bit n.
1 Output slew rate control enabled for port A bit n.
7
6
5
4
3
2
1
0
R
W
PTADS7
PTADS6
PTADS5
PTADS4
PTADS3
PTADS2
PTADS1
PTADS0
Reset
0
0
0
0
0
0
0
0
Figure 6-13. Output Drive Strength Selection for Port A (PTASE)
Table 6-6. PTASE Register Field Descriptions
Description
Field
7:0
Output Drive Strength Selection for Port A Bits — Each of these control bits selects between low and high
PTADS[7:0] output drive for the associated PTA pin.
0 Low output drive enabled for port A bit n.
1 High output drive enabled for port A bit n.
MC9S08AW60 Data Sheet, Rev 2
90
Freescale Semiconductor
Chapter 6 Parallel Input/Output
6.7.3
Port B I/O Registers (PTBD and PTBDD)
Port B parallel I/O function is controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTBD7
PTBD6
PTBD5
PTBD4
PTBD3
PTBD2
PTBD1
PTBD0
Reset
0
0
0
0
0
0
0
0
Figure 6-14. Port B Data Register (PTBD)
Table 6-7. PTBD Register Field Descriptions
Description
Field
7:0
Port B Data Register Bits — For port B pins that are inputs, reads return the logic level on the pin. For port B
PTBD[7:0] pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port B pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTBD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures
all port pins as high-impedance inputs with pullups disabled.
7
6
5
4
3
2
1
0
R
W
PTBDD7
PTBDD6
PTBDD5
PTBDD4
PTBDD3
PTBDD2
PTBDD1
PTBDD0
Reset
0
0
0
0
0
0
0
0
Figure 6-15. Data Direction for Port B (PTBDD)
Table 6-8. PTBDD Register Field Descriptions
Description
Field
7:0
Data Direction for Port B Bits — These read/write bits control the direction of port B pins and what is read for
PTBDD[7:0] PTBD reads.
0 Input (output driver disabled) and reads return the pin value.
1 Output driver enabled for port B bit n and PTBD reads return the contents of PTBDn.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
91
Chapter 6 Parallel Input/Output
6.7.4
Port B Pin Control Registers (PTBPE, PTBSE, PTBDS)
In addition to the I/O control, port B pins are controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTBPE7
PTBPE6
PTBPE5
PTBPE4
PTBPE3
PTBPE2
PTBPE1
PTBPE0
Reset
0
0
0
0
0
0
0
0
Figure 6-16. Internal Pullup Enable for Port B (PTBPE)
Table 6-9. PTBPE Register Field Descriptions
Description
Field
7:0
Internal Pullup Enable for Port B Bits — Each of these control bits determines if the internal pullup device is
PTBPE[7:0] enabled for the associated PTB pin. For port B pins that are configured as outputs, these bits have no effect and
the internal pullup devices are disabled.
0 Internal pullup device disabled for port B bit n.
1 Internal pullup device enabled for port B bit n.
7
6
5
4
3
2
1
0
R
W
PTBSE7
PTBSE6
PTBSE5
PTBSE4
PTBSE3
PTBSE2
PTBSE1
PTBSE0
Reset
0
0
0
0
0
0
0
0
Figure 6-17. Output Slew Rate Control Enable (PTBSE)
Table 6-10. PTBSE Register Field Descriptions
Description
Field
7:0
Output Slew Rate Control Enable for Port B Bits— Each of these control bits determine whether output slew
PTBSE[7:0] rate control is enabled for the associated PTB pin. For port B pins that are configured as inputs, these bits have
no effect.
0 Output slew rate control disabled for port B bit n.
1 Output slew rate control enabled for port B bit n.
MC9S08AW60 Data Sheet, Rev 2
92
Freescale Semiconductor
Chapter 6 Parallel Input/Output
7
6
5
4
3
2
1
0
R
W
PTBDS7
PTBDS6
PTBDS5
PTBDS4
PTBDS3
PTBDS2
PTBDS1
PTBDS0
Reset
0
0
0
0
0
0
0
0
Figure 6-18. Output Drive Strength Selection for Port B (PTBDS)
Table 6-11. PTBDS Register Field Descriptions
Description
Field
7:0
Output Drive Strength Selection for Port B Bits — Each of these control bits selects between low and high
PTBDS[7:0] output drive for the associated PTB pin.
0 Low output drive enabled for port B bit n.
1 High output drive enabled for port B bit n.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
93
Chapter 6 Parallel Input/Output
6.7.5
Port C I/O Registers (PTCD and PTCDD)
Port C parallel I/O function is controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTCD6
PTCD5
PTCD4
PTCD3
PTCD2
PTCD1
PTCD0
Reset
0
0
0
0
0
0
0
0
Figure 6-19. Port C Data Register (PTCD)
Table 6-12. PTCD Register Field Descriptions
Description
Field
6:0
Port C Data Register Bits — For port C pins that are inputs, reads return the logic level on the pin. For port C
PTCD[6:0] pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port C pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTCD to all 0s, but these 0s are not driven out the corresponding pins because reset also
configures all port pins as high-impedance inputs with pullups disabled.
7
6
5
4
3
2
1
0
R
W
PTCDD6
PTCDD5
PTCDD4
PTCDD3
PTCDD2
PTCDD1
PTCDD0
Reset
0
0
0
0
0
0
0
0
Figure 6-20. Data Direction for Port C (PTCDD)
Table 6-13. PTCDD Register Field Descriptions
Description
Field
6:0
Data Direction for Port C Bits — These read/write bits control the direction of port C pins and what is read for
PTCDD[6:0] PTCD reads.
0 Input (output driver disabled) and reads return the pin value.
1 Output driver enabled for port C bit n and PTCD reads return the contents of PTCDn.
MC9S08AW60 Data Sheet, Rev 2
94
Freescale Semiconductor
Chapter 6 Parallel Input/Output
6.7.6
Port C Pin Control Registers (PTCPE, PTCSE, PTCDS)
In addition to the I/O control, port C pins are controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTCPE6
PTCPE5
PTCPE4
PTCPE3
PTCPE2
PTCPE1
PTCPE0
Reset
0
0
0
0
0
0
0
0
Figure 6-21. Internal Pullup Enable for Port C (PTCPE)
Table 6-14. PTCPE Register Field Descriptions
Description
Field
6:0
Internal Pullup Enable for Port C Bits — Each of these control bits determines if the internal pullup device is
PTCPE[6:0] enabled for the associated PTC pin. For port C pins that are configured as outputs, these bits have no effect and
the internal pullup devices are disabled.
0 Internal pullup device disabled for port C bit n.
1 Internal pullup device enabled for port C bit n.
7
6
5
4
3
2
1
0
R
W
PTCSE6
PTCSE5
PTCSE4
PTCSE3
PTCSE2
PTCSE1
PTCSE0
Reset
0
0
0
0
0
0
0
0
Figure 6-22. Output Slew Rate Control Enable for Port C (PTCSE)
Table 6-15. PTCSE Register Field Descriptions
Description
Field
6:0
Output Slew Rate Control Enable for Port C Bits — Each of these control bits determine whether output slew
PTCSE[6:0] rate control is enabled for the associated PTC pin. For port C pins that are configured as inputs, these bits have
no effect.
0 Output slew rate control disabled for port C bit n.
1 Output slew rate control enabled for port C bit n.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
95
Chapter 6 Parallel Input/Output
7
6
5
4
3
2
1
0
R
PTCDS6
0
PTCDS5
PTCDS4
PTCDS3
PTCDS2
PTCDS1
PTCDS0
W
Reset
0
0
0
0
0
0
0
Figure 6-23. Output Drive Strength Selection for Port C (PTCDS)
Table 6-16. PTCDS Register Field Descriptions
Description
Field
6:0
Output Drive Strength Selection for Port C Bits — Each of these control bits selects between low and high
PTCDS[6:0] output drive for the associated PTC pin.
0 Low output drive enabled for port C bit n.
1 High output drive enabled for port C bit n.
MC9S08AW60 Data Sheet, Rev 2
96
Freescale Semiconductor
Chapter 6 Parallel Input/Output
6.7.7
Port D I/O Registers (PTDD and PTDDD)
Port D parallel I/O function is controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTDD7
PTDD6
PTDD5
PTDD4
PTDD3
PTDD2
PTDD1
PTDD0
Reset
0
0
0
0
0
0
0
0
Figure 6-24. Port D Data Register (PTDD)
Table 6-17. PTDD Register Field Descriptions
Description
Field
7:0
Port D Data Register Bits — For port D pins that are inputs, reads return the logic level on the pin. For port D
PTDD[7:0] pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port D pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTDD to all 0s, but these 0s are not driven out the corresponding pins because reset also
configures all port pins as high-impedance inputs with pullups disabled.
7
6
5
4
3
2
1
0
R
W
PTDDD7
PTDDD6
PTDDD5
PTDDD4
PTDDD3
PTDDD2
PTDDD1
PTDDD0
Reset
0
0
0
0
0
0
0
0
Figure 6-25. Data Direction for Port D (PTDDD)
Table 6-18. PTDDD Register Field Descriptions
Description
Field
7:0
Data Direction for Port D Bits — These read/write bits control the direction of port D pins and what is read for
PTDDD[7:0] PTDD reads.
0 Input (output driver disabled) and reads return the pin value.
1 Output driver enabled for port D bit n and PTDD reads return the contents of PTDDn.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
97
Chapter 6 Parallel Input/Output
6.7.8
Port D Pin Control Registers (PTDPE, PTDSE, PTDDS)
In addition to the I/O control, port D pins are controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTDPE7
PTDPE6
PTDPE5
PTDPE4
PTDPE3
PTDPE2
PTDPE1
PTDPE0
Reset
0
0
0
0
0
0
0
0
Figure 6-26. Internal Pullup Enable for Port D (PTDPE)
Table 6-19. PTDPE Register Field Descriptions
Description
Field
7:0
Internal Pullup Enable for Port D Bits — Each of these control bits determines if the internal pullup device is
PTDPE[7:0] enabled for the associated PTD pin. For port D pins that are configured as outputs, these bits have no effect and
the internal pullup devices are disabled.
0 Internal pullup device disabled for port D bit n.
1 Internal pullup device enabled for port D bit n.
7
6
5
4
3
2
1
0
R
W
PTDSE7
PTDSE6
PTDSE5
PTDSE4
PTDSE3
PTDSE2
PTDSE1
PTDSE0
Reset
0
0
0
0
0
0
0
0
Figure 6-27. Output Slew Rate Control Enable for Port D (PTDSE)
Table 6-20. PTDSE Register Field Descriptions
Description
Field
7:0
Output Slew Rate Control Enable for Port D Bits — Each of these control bits determine whether output slew
PTDSE[7:0] rate control is enabled for the associated PTD pin. For port D pins that are configured as inputs, these bits have
no effect.
0 Output slew rate control disabled for port D bit n.
1 Output slew rate control enabled for port D bit n.
MC9S08AW60 Data Sheet, Rev 2
98
Freescale Semiconductor
Chapter 6 Parallel Input/Output
7
6
5
4
3
2
1
0
R
W
PTDDS7
PTDDS6
PTDDS5
PTDDS4
PTDDS3
PTDDS2
PTDDS1
PTDDS0
Reset
0
0
0
0
0
0
0
0
Figure 6-28. Output Drive Strength Selection for Port D (PTDDS)
Table 6-21. PTDDS Register Field Descriptions
Description
Field
7:0
Output Drive Strength Selection for Port D Bits — Each of these control bits selects between low and high
PTDDS[7:0] output drive for the associated PTD pin.
0 Low output drive enabled for port D bit n.
1 High output drive enabled for port D bit n.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
99
Chapter 6 Parallel Input/Output
6.7.9
Port E I/O Registers (PTED and PTEDD)
Port E parallel I/O function is controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTED7
PTED6
PTED5
PTED4
PTED3
PTED2
PTED1
PTED0
Reset
0
0
0
0
0
0
0
0
Figure 6-29. Port E Data Register (PTED)
Table 6-22. PTED Register Field Descriptions
Description
Field
7:0
Port E Data Register Bits — For port E pins that are inputs, reads return the logic level on the pin. For port E
PTED[7:0] pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port E pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTED to all 0s, but these 0s are not driven out the corresponding pins because reset also configures
all port pins as high-impedance inputs with pullups disabled.
7
6
5
4
3
2
1
0
R
W
PTEDD7
PTEDD6
PTEDD5
PTEDD4
PTEDD3
PTEDD2
PTEDD1
PTEDD0
Reset
0
0
0
0
0
0
0
0
Figure 6-30. Data Direction for Port E (PTEDD)
Table 6-23. PTEDD Register Field Descriptions
Description
Field
7:0
Data Direction for Port E Bits — These read/write bits control the direction of port E pins and what is read for
PTEDD[7:0] PTED reads.
0 Input (output driver disabled) and reads return the pin value.
1 Output driver enabled for port E bit n and PTED reads return the contents of PTEDn.
MC9S08AW60 Data Sheet, Rev 2
100
Freescale Semiconductor
Chapter 6 Parallel Input/Output
6.7.10 Port E Pin Control Registers (PTEPE, PTESE, PTEDS)
In addition to the I/O control, port E pins are controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTEPE7
PTEPE6
PTEPE5
PTEPE4
PTEPE3
PTEPE2
PTEPE1
PTEPE0
Reset
0
0
0
0
0
0
0
0
Figure 6-31. Internal Pullup Enable for Port E (PTEPE)
Table 6-24. PTEPE Register Field Descriptions
Description
Field
7:0
Internal Pullup Enable for Port E Bits— Each of these control bits determines if the internal pullup device is
PTEPE[7:0] enabled for the associated PTE pin. For port E pins that are configured as outputs, these bits have no effect and
the internal pullup devices are disabled.
0 Internal pullup device disabled for port E bit n.
1 Internal pullup device enabled for port E bit n.
7
6
5
4
3
2
1
0
R
W
PTESE7
PTESE6
PTESE5
PTESE4
PTESE3
PTESE2
PTESE1
PTESE0
Reset
0
0
0
0
0
0
0
0
Figure 6-32. Output Slew Rate Control Enable for Port E (PTESE)
Table 6-25. PTESE Register Field Descriptions
Description
Field
7:0
Output Slew Rate Control Enable for Port E Bits — Each of these control bits determine whether output slew
PTESE[7:0] rate control is enabled for the associated PTE pin. For port E pins that are configured as inputs, these bits have
no effect.
0 Output slew rate control disabled for port E bit n.
1 Output slew rate control enabled for port E bit n.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
101
Chapter 6 Parallel Input/Output
7
6
5
4
3
2
1
0
R
PTEDS7
0
PTEDS6
0
PTEDS5
PTEDS4
PTEDS3
PTEDS2
PTEDS1
PTEDS0
W
Reset
0
0
0
0
0
0
Figure 6-33. Output Drive Strength Selection for Port E (PTEDS)
Table 6-26. PTEDS Register Field Descriptions
Description
Field
7:0
Output Drive Strength Selection for Port E Bits — Each of these control bits selects between low and high
PTEDS[7:0] output drive for the associated PTE pin.
0 Low output drive enabled for port E bit n.
1 High output drive enabled for port E bit n.
MC9S08AW60 Data Sheet, Rev 2
102
Freescale Semiconductor
Chapter 6 Parallel Input/Output
6.7.11 Port F I/O Registers (PTFD and PTFDD)
Port F parallel I/O function is controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTFD7
PTFD6
PTFD5
PTFD4
PTFD3
PTFD2
PTFD1
PTFD0
Reset
0
0
0
0
0
0
0
0
Figure 6-34. Port F Data Register (PTFD)
Table 6-27. PTFD Register Field Descriptions
Description
Field
7:0
Port F Data Register Bits— For port F pins that are inputs, reads return the logic level on the pin. For port F
PTFD[7:0] pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port F pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTFD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures
all port pins as high-impedance inputs with pullups disabled.
7
6
5
4
3
2
1
0
R
W
PTFDD7
PTFDD6
PTFDD5
PTFDD4
PTFDD3
PTFDD2
PTFDD1
PTFDD0
Reset
0
0
0
0
0
0
0
0
Figure 6-35. Data Direction for Port F (PTFDD)
Table 6-28. PTFDD Register Field Descriptions
Description
Field
7:0
Data Direction for Port F Bits — These read/write bits control the direction of port F pins and what is read for
PTFDD[7:0] PTFD reads.
0 Input (output driver disabled) and reads return the pin value.
1 Output driver enabled for port F bit n and PTFD reads return the contents of PTFDn.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
103
Chapter 6 Parallel Input/Output
6.7.12 Port F Pin Control Registers (PTFPE, PTFSE, PTFDS)
In addition to the I/O control, port F pins are controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTFPE7
PTFPE6
PTFPE5
PTFPE4
PTFPE3
PTFPE2
PTFPE1
PTFPE0
Reset
0
0
0
0
0
0
0
0
Figure 6-36. Internal Pullup Enable for Port F (PTFPE)
Table 6-29. PTFPE Register Field Descriptions
Description
Field
7:0
Internal Pullup Enable for Port F Bits — Each of these control bits determines if the internal pullup device is
PTFPE[7:0] enabled for the associated PTF pin. For port F pins that are configured as outputs, these bits have no effect and
the internal pullup devices are disabled.
0 Internal pullup device disabled for port F bit n.
1 Internal pullup device enabled for port F bit n.
7
6
5
4
3
2
1
0
R
W
PTFSE7
PTFSE6
PTFSE5
PTFSE4
PTFSE3
PTFSE2
PTFSE1
PTFSE0
Reset
0
0
0
0
0
0
0
0
Figure 6-37. Output Slew Rate Control Enable for Port F (PTFSE)
Table 6-30. PTFSE Register Field Descriptions
Description
Field
7:0
Output Slew Rate Control Enable for Port F Bits — Each of these control bits determine whether output slew
PTFSE[7:0] rate control is enabled for the associated PTF pin. For port F pins that are configured as inputs, these bits have
no effect.
0 Output slew rate control disabled for port F bit n.
1 Output slew rate control enabled for port F bit n.
MC9S08AW60 Data Sheet, Rev 2
104
Freescale Semiconductor
Chapter 6 Parallel Input/Output
7
6
5
4
3
2
1
0
R
W
PTFDS7
PTFDS6
PTFDS5
PTFDS4
PTFDS3
PTFDS2
PTFDS1
PTFDS0
Reset
0
0
0
0
0
0
0
0
Figure 6-38. Output Drive Strength Selection for Port F (PTFDS)
Table 6-31. PTFDS Register Field Descriptions
Description
Field
7:0
Output Drive Strength Selection for Port F Bits — Each of these control bits selects between low and high
PTFDS[7:0] output drive for the associated PTF pin.
0 Low output drive enabled for port F bit n.
1 High output drive enabled for port F bit n.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
105
Chapter 6 Parallel Input/Output
6.7.13 Port G I/O Registers (PTGD and PTGDD)
Port G parallel I/O function is controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTGD6
PTGD5
PTGD4
PTGD3
PTGD2
PTGD1
PTGD0
Reset
0
0
0
0
0
0
0
0
Figure 6-39. Port G Data Register (PTGD)
Table 6-32. PTGD Register Field Descriptions
Description
Field
6:0
Port G Data Register Bits — For port G pins that are inputs, reads return the logic level on the pin. For port G
PTGD[6:0] pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port G pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTGD to all 0s, but these 0s are not driven out the corresponding pins because reset also
configures all port pins as high-impedance inputs with pullups disabled.
7
6
5
4
3
2
1
0
R
W
PTGDD6
PTGDD5
PTGDD4
PTGDD3
PTGDD2
PTGDD1
PTGDD0
Reset
0
0
0
0
0
0
0
0
Figure 6-40. Data Direction for Port G (PTGDD)
Table 6-33. PTGDD Register Field Descriptions
Description
Field
6:0
Data Direction for Port G Bits — These read/write bits control the direction of port G pins and what is read for
PTGDD[6:0] PTGD reads.
0 Input (output driver disabled) and reads return the pin value.
1 Output driver enabled for port G bit n and PTGD reads return the contents of PTGDn.
MC9S08AW60 Data Sheet, Rev 2
106
Freescale Semiconductor
Chapter 6 Parallel Input/Output
6.7.14 Port G Pin Control Registers (PTGPE, PTGSE, PTGDS)
In addition to the I/O control, port G pins are controlled by the registers listed below.
7
6
5
4
3
2
1
0
R
W
PTGPE6
PTGPE5
PTGPE4
PTGPE3
PTGPE2
PTGPE1
PTGPE0
Reset
0
0
0
0
0
0
0
0
Figure 6-41. Internal Pullup Enable for Port G Bits (PTGPE)
Table 6-34. PTGPE Register Field Descriptions
Description
Field
6:0
Internal Pullup Enable for Port G Bits — Each of these control bits determines if the internal pullup device is
PTGPE[6:0] enabled for the associated PTG pin. For port G pins that are configured as outputs, these bits have no effect and
the internal pullup devices are disabled.
0 Internal pullup device disabled for port G bit n.
1 Internal pullup device enabled for port G bit n.
7
6
5
4
3
2
1
0
R
W
PTGSE6
PTGSE5
PTGSE4
PTGSE3
PTGSE2
PTGSE1
PTGSE0
Reset
0
0
0
0
0
0
0
0
Figure 6-42. Output Slew Rate Control Enable for Port G Bits (PTGSE)
Table 6-35. PTGSE Register Field Descriptions
Description
Field
6:0
Output Slew Rate Control Enable for Port G Bits— Each of these control bits determine whether output slew
PTGSE[6:0] rate control is enabled for the associated PTG pin. For port G pins that are configured as inputs, these bits have
no effect.
0 Output slew rate control disabled for port G bit n.
1 Output slew rate control enabled for port G bit n.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
107
Chapter 6 Parallel Input/Output
7
6
5
4
3
2
1
0
R
PTGDS6
0
PTGDS5
PTGDS4
PTGDS3
PTGDS2
PTGDS1
PTGDS0
W
Reset
0
0
0
0
0
0
0
Figure 6-43. Output Drive Strength Selection for Port G (PTGDS)
Table 6-36. PTGDS Register Field Descriptions
Description
Field
6:0
Output Drive Strength Selection for Port G Bits — Each of these control bits selects between low and high
PTGDS[6:0] output drive for the associated PTG pin.
0 Low output drive enabled for port G bit n.
1 High output drive enabled for port G bit n.
MC9S08AW60 Data Sheet, Rev 2
108
Freescale Semiconductor
Chapter 7
Central Processor Unit (S08CPUV2)
7.1
Introduction
This section provides summary information about the registers, addressing modes, and instruction set of
the CPU of the HCS08 family. For a more detailed discussion, refer to the HCS08 Family Reference
Manual, volume 1, Freescale Semiconductor document order number HCS08RMV1/D.
The HCS08 CPU is fully source- and object-code-compatible with the M68HC08 CPU. Several
instructions and enhanced addressing modes were added to improve C compiler efficiency and to support
a new background debug system which replaces the monitor mode of earlier M68HC08 microcontrollers
(MCU).
7.1.1
Features
Features of the HCS08 CPU include:
•
•
•
•
•
•
•
Object code fully upward-compatible with M68HC05 and M68HC08 Families
All registers and memory are mapped to a single 64-Kbyte address space
16-bit stack pointer (any size stack anywhere in 64-Kbyte address space)
16-bit index register (H:X) with powerful indexed addressing modes
8-bit accumulator (A)
Many instructions treat X as a second general-purpose 8-bit register
Seven addressing modes:
— Inherent — Operands in internal registers
— Relative — 8-bit signed offset to branch destination
— Immediate — Operand in next object code byte(s)
— Direct — Operand in memory at 0x0000–0x00FF
— Extended — Operand anywhere in 64-Kbyte address space
— Indexed relative to H:X — Five submodes including auto increment
— Indexed relative to SP — Improves C efficiency dramatically
Memory-to-memory data move instructions with four address mode combinations
•
•
Overflow, half-carry, negative, zero, and carry condition codes support conditional branching on
the results of signed, unsigned, and binary-coded decimal (BCD) operations
•
•
•
Efficient bit manipulation instructions
Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions
STOP and WAIT instructions to invoke low-power operating modes
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
109
Chapter 7 Central Processor Unit (S08CPUV2)
7.2
Programmer’s Model and CPU Registers
Figure 7-1 shows the five CPU registers. CPU registers are not part of the memory map.
7
0
ACCUMULATOR
A
16-BIT INDEX REGISTER H:X
INDEX REGISTER (HIGH) INDEX REGISTER (LOW)
H
X
15
8
7
0
SP
PC
STACK POINTER
15
0
PROGRAM COUNTER
7
0
CONDITION CODE REGISTER
V
1
1
H
I
N
Z
C
CCR
CARRY
ZERO
NEGATIVE
INTERRUPT MASK
HALF-CARRY (FROM BIT 3)
TWO’S COMPLEMENT OVERFLOW
Figure 7-1. CPU Registers
7.2.1
Accumulator (A)
The A accumulator is a general-purpose 8-bit register. One operand input to the arithmetic logic unit
(ALU) is connected to the accumulator and the ALU results are often stored into the A accumulator after
arithmetic and logical operations. The accumulator can be loaded from memory using various addressing
modes to specify the address where the loaded data comes from, or the contents of A can be stored to
memory using various addressing modes to specify the address where data from A will be stored.
Reset has no effect on the contents of the A accumulator.
7.2.2
Index Register (H:X)
This 16-bit register is actually two separate 8-bit registers (H and X), which often work together as a 16-bit
address pointer where H holds the upper byte of an address and X holds the lower byte of the address. All
indexed addressing mode instructions use the full 16-bit value in H:X as an index reference pointer;
however, for compatibility with the earlier M68HC05 family, some instructions operate only on the
low-order 8-bit half (X).
Many instructions treat X as a second general-purpose 8-bit register that can be used to hold 8-bit data
values. X can be cleared, incremented, decremented, complemented, negated, shifted, or rotated. Transfer
instructions allow data to be transferred from A or transferred to A where arithmetic and logical operations
can then be performed.
For compatibility with the earlier M68HC05 family, H is forced to 0x00 during reset. Reset has no effect
on the contents of X.
MC9S08AW60 Data Sheet, Rev 2
110
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
7.2.3
Stack Pointer (SP)
This 16-bit address pointer register points at the next available location on the automatic last-in-first-out
(LIFO) stack. The stack may be located anywhere in the 64-Kbyte address space that has RAM and can
be any size up to the amount of available RAM. The stack is used to automatically save the return address
for subroutine calls, the return address and CPU registers during interrupts, and for local variables. The
AIS (add immediate to stack pointer) instruction adds an 8-bit signed immediate value to SP. This is most
often used to allocate or deallocate space for local variables on the stack.
SP is forced to 0x00FF at reset for compatibility with the earlier M68HC05 family. HCS08 programs
normally change the value in SP to the address of the last location (highest address) in on-chip RAM
during reset initialization to free up direct page RAM (from the end of the on-chip registers to 0x00FF).
The RSP (reset stack pointer) instruction was included for compatibility with the M68HC05 family and is
seldom used in new HCS08 programs because it only affects the low-order half of the stack pointer.
7.2.4
Program Counter (PC)
The program counter is a 16-bit register that contains the address of the next instruction or operand to be
fetched.
During normal program execution, the program counter automatically increments to the next sequential
memory location every time an instruction or operand is fetched. Jump, branch, interrupt, and return
operations load the program counter with an address other than that of the next sequential location. This
is called a change-of-flow.
During reset, the program counter is loaded with the reset vector that is located at 0xFFFE and 0xFFFF.
The vector stored there is the address of the first instruction that will be executed after exiting the reset
state.
7.2.5
Condition Code Register (CCR)
The 8-bit condition code register contains the interrupt mask (I) and five flags that indicate the results of
the instruction just executed. Bits 6 and 5 are set permanently to 1. The following paragraphs describe the
functions of the condition code bits in general terms. For a more detailed explanation of how each
instruction sets the CCR bits, refer to the HCS08 Family Reference Manual, volume 1, Freescale
Semiconductor document order number HCS08RMv1.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
111
Chapter 7 Central Processor Unit (S08CPUV2)
7
0
CONDITION CODE REGISTER
V
1
1
H
I
N
Z
C
CCR
CARRY
ZERO
NEGATIVE
INTERRUPT MASK
HALF-CARRY (FROM BIT 3)
TWO’S COMPLEMENT OVERFLOW
Figure 7-2. Condition Code Register
Table 7-1. CCR Register Field Descriptions
Description
Field
7
Two’s Complement Overflow Flag — The CPU sets the overflow flag when a two’s complement overflow occurs.
V
The signed branch instructions BGT, BGE, BLE, and BLT use the overflow flag.
0 No overflow
1 Overflow
4
H
Half-Carry Flag — The CPU sets the half-carry flag when a carry occurs between accumulator bits 3 and 4 during
an add-without-carry (ADD) or add-with-carry (ADC) operation. The half-carry flag is required for binary-coded
decimal (BCD) arithmetic operations. The DAA instruction uses the states of the H and C condition code bits to
automatically add a correction value to the result from a previous ADD or ADC on BCD operands to correct the
result to a valid BCD value.
0 No carry between bits 3 and 4
1 Carry between bits 3 and 4
3
I
Interrupt Mask Bit — When the interrupt mask is set, all maskable CPU interrupts are disabled. CPU interrupts
are enabled when the interrupt mask is cleared. When a CPU interrupt occurs, the interrupt mask is set
automatically after the CPU registers are saved on the stack, but before the first instruction of the interrupt service
routine is executed.
Interrupts are not recognized at the instruction boundary after any instruction that clears I (CLI or TAP). This
ensures that the next instruction after a CLI or TAP will always be executed without the possibility of an intervening
interrupt, provided I was set.
0 Interrupts enabled
1 Interrupts disabled
2
N
Negative Flag — The CPU sets the negative flag when an arithmetic operation, logic operation, or data
manipulation produces a negative result, setting bit 7 of the result. Simply loading or storing an 8-bit or 16-bit value
causes N to be set if the most significant bit of the loaded or stored value was 1.
0 Non-negative result
1 Negative result
1
Z
Zero Flag — The CPU sets the zero flag when an arithmetic operation, logic operation, or data manipulation
produces a result of 0x00 or 0x0000. Simply loading or storing an 8-bit or 16-bit value causes Z to be set if the
loaded or stored value was all 0s.
0 Non-zero result
1 Zero result
0
C
Carry/Borrow Flag — The CPU sets the carry/borrow flag when an addition operation produces a carry out of bit
7 of the accumulator or when a subtraction operation requires a borrow. Some instructions — such as bit test and
branch, shift, and rotate — also clear or set the carry/borrow flag.
0 No carry out of bit 7
1 Carry out of bit 7
MC9S08AW60 Data Sheet, Rev 2
112
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
7.3
Addressing Modes
Addressing modes define the way the CPU accesses operands and data. In the HCS08, all memory, status
and control registers, and input/output (I/O) ports share a single 64-Kbyte linear address space so a 16-bit
binary address can uniquely identify any memory location. This arrangement means that the same
instructions that access variables in RAM can also be used to access I/O and control registers or nonvolatile
program space.
Some instructions use more than one addressing mode. For instance, move instructions use one addressing
mode to specify the source operand and a second addressing mode to specify the destination address.
Instructions such as BRCLR, BRSET, CBEQ, and DBNZ use one addressing mode to specify the location
of an operand for a test and then use relative addressing mode to specify the branch destination address
when the tested condition is true. For BRCLR, BRSET, CBEQ, and DBNZ, the addressing mode listed in
the instruction set tables is the addressing mode needed to access the operand to be tested, and relative
addressing mode is implied for the branch destination.
7.3.1
Inherent Addressing Mode (INH)
In this addressing mode, operands needed to complete the instruction (if any) are located within CPU
registers so the CPU does not need to access memory to get any operands.
7.3.2
Relative Addressing Mode (REL)
Relative addressing mode is used to specify the destination location for branch instructions. A signed 8-bit
offset value is located in the memory location immediately following the opcode. During execution, if the
branch condition is true, the signed offset is sign-extended to a 16-bit value and is added to the current
contents of the program counter, which causes program execution to continue at the branch destination
address.
7.3.3
Immediate Addressing Mode (IMM)
In immediate addressing mode, the operand needed to complete the instruction is included in the object
code immediately following the instruction opcode in memory. In the case of a 16-bit immediate operand,
the high-order byte is located in the next memory location after the opcode, and the low-order byte is
located in the next memory location after that.
7.3.4
Direct Addressing Mode (DIR)
In direct addressing mode, the instruction includes the low-order eight bits of an address in the direct page
(0x0000–0x00FF). During execution a 16-bit address is formed by concatenating an implied 0x00 for the
high-order half of the address and the direct address from the instruction to get the 16-bit address where
the desired operand is located. This is faster and more memory efficient than specifying a complete 16-bit
address for the operand.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
113
Chapter 7 Central Processor Unit (S08CPUV2)
7.3.5
Extended Addressing Mode (EXT)
In extended addressing mode, the full 16-bit address of the operand is located in the next two bytes of
program memory after the opcode (high byte first).
7.3.6
Indexed Addressing Mode
Indexed addressing mode has seven variations including five that use the 16-bit H:X index register pair and
two that use the stack pointer as the base reference.
7.3.6.1
Indexed, No Offset (IX)
This variation of indexed addressing uses the 16-bit value in the H:X index register pair as the address of
the operand needed to complete the instruction.
7.3.6.2
Indexed, No Offset with Post Increment (IX+)
This variation of indexed addressing uses the 16-bit value in the H:X index register pair as the address of
the operand needed to complete the instruction. The index register pair is then incremented
(H:X = H:X + 0x0001) after the operand has been fetched. This addressing mode is only used for MOV
and CBEQ instructions.
7.3.6.3
Indexed, 8-Bit Offset (IX1)
This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus an unsigned
8-bit offset included in the instruction as the address of the operand needed to complete the instruction.
7.3.6.4
Indexed, 8-Bit Offset with Post Increment (IX1+)
This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus an unsigned
8-bit offset included in the instruction as the address of the operand needed to complete the instruction.
The index register pair is then incremented (H:X = H:X + 0x0001) after the operand has been fetched. This
addressing mode is used only for the CBEQ instruction.
7.3.6.5
Indexed, 16-Bit Offset (IX2)
This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus a 16-bit offset
included in the instruction as the address of the operand needed to complete the instruction.
7.3.6.6
SP-Relative, 8-Bit Offset (SP1)
This variation of indexed addressing uses the 16-bit value in the stack pointer (SP) plus an unsigned 8-bit
offset included in the instruction as the address of the operand needed to complete the instruction.
MC9S08AW60 Data Sheet, Rev 2
114
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
7.3.6.7
SP-Relative, 16-Bit Offset (SP2)
This variation of indexed addressing uses the 16-bit value in the stack pointer (SP) plus a 16-bit offset
included in the instruction as the address of the operand needed to complete the instruction.
7.4
Special Operations
The CPU performs a few special operations that are similar to instructions but do not have opcodes like
other CPU instructions. In addition, a few instructions such as STOP and WAIT directly affect other MCU
circuitry. This section provides additional information about these operations.
7.4.1
Reset Sequence
Reset can be caused by a power-on-reset (POR) event, internal conditions such as the COP (computer
operating properly) watchdog, or by assertion of an external active-low reset pin. When a reset event
occurs, the CPU immediately stops whatever it is doing (the MCU does not wait for an instruction
boundary before responding to a reset event). For a more detailed discussion about how the MCU
recognizes resets and determines the source, refer to the Resets, Interrupts, and System Configuration
chapter.
The reset event is considered concluded when the sequence to determine whether the reset came from an
internal source is done and when the reset pin is no longer asserted. At the conclusion of a reset event, the
CPU performs a 6-cycle sequence to fetch the reset vector from 0xFFFE and 0xFFFF and to fill the
instruction queue in preparation for execution of the first program instruction.
7.4.2
Interrupt Sequence
When an interrupt is requested, the CPU completes the current instruction before responding to the
interrupt. At this point, the program counter is pointing at the start of the next instruction, which is where
the CPU should return after servicing the interrupt. The CPU responds to an interrupt by performing the
same sequence of operations as for a software interrupt (SWI) instruction, except the address used for the
vector fetch is determined by the highest priority interrupt that is pending when the interrupt sequence
started.
The CPU sequence for an interrupt is:
1. Store the contents of PCL, PCH, X, A, and CCR on the stack, in that order.
2. Set the I bit in the CCR.
3. Fetch the high-order half of the interrupt vector.
4. Fetch the low-order half of the interrupt vector.
5. Delay for one free bus cycle.
6. Fetch three bytes of program information starting at the address indicated by the interrupt vector
to fill the instruction queue in preparation for execution of the first instruction in the interrupt
service routine.
After the CCR contents are pushed onto the stack, the I bit in the CCR is set to prevent other interrupts
while in the interrupt service routine. Although it is possible to clear the I bit with an instruction in the
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
115
Chapter 7 Central Processor Unit (S08CPUV2)
interrupt service routine, this would allow nesting of interrupts (which is not recommended because it
leads to programs that are difficult to debug and maintain).
For compatibility with the earlier M68HC05 MCUs, the high-order half of the H:X index register pair (H)
is not saved on the stack as part of the interrupt sequence. The user must use a PSHH instruction at the
beginning of the service routine to save H and then use a PULH instruction just before the RTI that ends
the interrupt service routine. It is not necessary to save H if you are certain that the interrupt service routine
does not use any instructions or auto-increment addressing modes that might change the value of H.
The software interrupt (SWI) instruction is like a hardware interrupt except that it is not masked by the
global I bit in the CCR and it is associated with an instruction opcode within the program so it is not
asynchronous to program execution.
7.4.3
Wait Mode Operation
The WAIT instruction enables interrupts by clearing the I bit in the CCR. It then halts the clocks to the
CPU to reduce overall power consumption while the CPU is waiting for the interrupt or reset event that
will wake the CPU from wait mode. When an interrupt or reset event occurs, the CPU clocks will resume
and the interrupt or reset event will be processed normally.
If a serial BACKGROUND command is issued to the MCU through the background debug interface while
the CPU is in wait mode, CPU clocks will resume and the CPU will enter active background mode where
other serial background commands can be processed. This ensures that a host development system can still
gain access to a target MCU even if it is in wait mode.
7.4.4
Stop Mode Operation
Usually, all system clocks, including the crystal oscillator (when used), are halted during stop mode to
minimize power consumption. In such systems, external circuitry is needed to control the time spent in
stop mode and to issue a signal to wake up the target MCU when it is time to resume processing. Unlike
the earlier M68HC05 and M68HC08 MCUs, the HCS08 can be configured to keep a minimum set of
clocks running in stop mode. This optionally allows an internal periodic signal to wake the target MCU
from stop mode.
When a host debug system is connected to the background debug pin (BKGD) and the ENBDM control
bit has been set by a serial command through the background interface (or because the MCU was reset into
active background mode), the oscillator is forced to remain active when the MCU enters stop mode. In this
case, if a serial BACKGROUND command is issued to the MCU through the background debug interface
while the CPU is in stop mode, CPU clocks will resume and the CPU will enter active background mode
where other serial background commands can be processed. This ensures that a host development system
can still gain access to a target MCU even if it is in stop mode.
Recovery from stop mode depends on the particular HCS08 and whether the oscillator was stopped in stop
mode. Refer to the Modes of Operation chapter for more details.
MC9S08AW60 Data Sheet, Rev 2
116
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
7.4.5
BGND Instruction
The BGND instruction is new to the HCS08 compared to the M68HC08. BGND would not be used in
normal user programs because it forces the CPU to stop processing user instructions and enter the active
background mode. The only way to resume execution of the user program is through reset or by a host
debug system issuing a GO, TRACE1, or TAGGO serial command through the background debug
interface.
Software-based breakpoints can be set by replacing an opcode at the desired breakpoint address with the
BGND opcode. When the program reaches this breakpoint address, the CPU is forced to active background
mode rather than continuing the user program.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
117
Chapter 7 Central Processor Unit (S08CPUV2)
7.5
HCS08 Instruction Set Summary
Instruction Set Summary Nomenclature
The nomenclature listed here is used in the instruction descriptions in Table 7-2.
Operators
( ) = Contents of register or memory location shown inside parentheses
←
&
|
⊕
×
÷
:
=
=
=
=
=
=
=
=
=
Is loaded with (read: “gets”)
Boolean AND
Boolean OR
Boolean exclusive-OR
Multiply
Divide
Concatenate
Add
+
–
Negate (two’s complement)
CPU registers
A
CCR
H
X
PC
PCH
PCL
SP
=
Accumulator
Condition code register
=
=
=
=
=
=
=
Index register, higher order (most significant) 8 bits
Index register, lower order (least significant) 8 bits
Program counter
Program counter, higher order (most significant) 8 bits
Program counter, lower order (least significant) 8 bits
Stack pointer
Memory and addressing
M = A memory location or absolute data, depending on addressing mode
M:M + 0x0001= A 16-bit value in two consecutive memory locations. The higher-order (most
significant) 8 bits are located at the address of M, and the lower-order (least
significant) 8 bits are located at the next higher sequential address.
Condition code register (CCR) bits
V
H
I
N
Z
C
=
=
=
=
=
=
Two’s complement overflow indicator, bit 7
Half carry, bit 4
Interrupt mask, bit 3
Negative indicator, bit 2
Zero indicator, bit 1
Carry/borrow, bit 0 (carry out of bit 7)
CCR activity notation
Bit not affected
–
=
MC9S08AW60 Data Sheet, Rev 2
118
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
0
1
=
=
=
=
Bit forced to 0
Bit forced to 1
Bit set or cleared according to results of operation
Undefined after the operation
U
Machine coding notation
dd
ee
ff
ii
jj
kk
hh
ll
=
=
=
=
=
=
=
=
=
Low-order 8 bits of a direct address 0x0000–0x00FF (high byte assumed to be 0x00)
Upper 8 bits of 16-bit offset
Lower 8 bits of 16-bit offset or 8-bit offset
One byte of immediate data
High-order byte of a 16-bit immediate data value
Low-order byte of a 16-bit immediate data value
High-order byte of 16-bit extended address
Low-order byte of 16-bit extended address
Relative offset
rr
Source form
Everything in the source forms columns, except expressions in italic characters, is literal information that
must appear in the assembly source file exactly as shown. The initial 3- to 5-letter mnemonic is always a
literal expression. All commas, pound signs (#), parentheses, and plus signs (+) are literal characters.
n — Any label or expression that evaluates to a single integer in the range 0–7
opr8i — Any label or expression that evaluates to an 8-bit immediate value
opr16i — Any label or expression that evaluates to a 16-bit immediate value
opr8a — Any label or expression that evaluates to an 8-bit value. The instruction treats this 8-bit
value as the low order 8 bits of an address in the direct page of the 64-Kbyte address
space (0x00xx).
opr16a — Any label or expression that evaluates to a 16-bit value. The instruction treats this
value as an address in the 64-Kbyte address space.
oprx8 — Any label or expression that evaluates to an unsigned 8-bit value, used for indexed
addressing
oprx16 — Any label or expression that evaluates to a 16-bit value. Because the HCS08 has a
16-bit address bus, this can be either a signed or an unsigned value.
rel — Any label or expression that refers to an address that is within –128 to +127 locations
from the next address after the last byte of object code for the current instruction. The
assembler will calculate the 8-bit signed offset and include it in the object code for this
instruction.
Address modes
INH
IMM
DIR
EXT
=
=
=
=
Inherent (no operands)
8-bit or 16-bit immediate
8-bit direct
16-bit extended
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
119
Chapter 7 Central Processor Unit (S08CPUV2)
IX
IX+
IX1
=
=
=
=
16-bit indexed no offset
16-bit indexed no offset, post increment (CBEQ and MOV only)
16-bit indexed with 8-bit offset from H:X
16-bit indexed with 8-bit offset, post increment
(CBEQ only)
IX1+
IX2
REL
SP1
SP2
=
=
=
=
16-bit indexed with 16-bit offset from H:X
8-bit relative offset
Stack pointer with 8-bit offset
Stack pointer with 16-bit offset
Table 7-2. HCS08 Instruction Set Summary (Sheet 1 of 7)
Effect
on CCR
Source
Form
Operation
Description
V H I N Z C
ADC #opr8i
IMM
DIR
EXT
IX2
A9 ii
B9 dd
2
3
4
4
3
3
5
4
ADC opr8a
ADC opr16a
ADC oprx16,X
ADC oprx8,X
ADC ,X
ADC oprx16,SP
ADC oprx8,SP
C9 hh ll
D9 ee ff
E9 ff
Add with Carry
A ← (A) + (M) + (C)
↕
↕
↕
↕
↕
↕
↕
↕
↕
↕
–
–
IX1
IX
SP2
SP1
F9
9ED9 ee ff
9EE9 ff
ADD #opr8i
ADD opr8a
IMM
DIR
EXT
IX2
AB ii
BB dd
2
3
4
4
3
3
5
4
ADD opr16a
ADD oprx16,X
ADD oprx8,X
ADD ,X
CB hh ll
DB ee ff
EB ff
Add without Carry
A ← (A) + (M)
IX1
IX
FB
ADD oprx16,SP
ADD oprx8,SP
SP2
SP1
9EDB ee ff
9EEB ff
Add Immediate Value
SP ← (SP) + (M)
AIS #opr8i
–
–
–
–
–
–
–
–
–
–
– IMM
A7 ii
2
(Signed) to Stack Pointer M is sign extended to a 16-bit value
Add Immediate Value
H:X ← (H:X) + (M)
AIX #opr8i
(Signed) to Index
– IMM
AF ii
2
M is sign extended to a 16-bit value
Register (H:X)
AND #opr8i
AND opr8a
IMM
DIR
EXT
A4 ii
B4 dd
2
3
4
4
3
3
5
4
AND opr16a
AND oprx16,X
AND oprx8,X
AND ,X
C4 hh ll
D4 ee ff
E4 ff
IX2
Logical AND
A ← (A) & (M)
0
–
–
–
–
↕
↕
↕
↕
–
IX1
IX
F4
AND oprx16,SP
AND oprx8,SP
SP2
SP1
9ED4 ee ff
9EE4 ff
ASL opr8a
ASLA
DIR
INH
38 dd
48
5
1
1
5
4
6
ASLX
Arithmetic Shift Left
(Same as LSL)
INH
58
↕
↕
C
0
ASL oprx8,X
ASL ,X
IX1
68 ff
78
b7
b0
b0
IX
ASL oprx8,SP
SP1
9E68 ff
ASR opr8a
ASRA
DIR
INH
37 dd
47
5
1
1
5
4
6
ASRX
INH
57
C
Arithmetic Shift Right
↕
–
–
–
–
↕
↕
↕
ASR oprx8,X
ASR ,X
IX1
67 ff
77
b7
IX
ASR oprx8,SP
SP1
9E67 ff
BCC rel
Branch if Carry Bit Clear
Branch if (C) = 0
–
–
–
– REL
24 rr
3
MC9S08AW60 Data Sheet, Rev 2
120
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
Table 7-2. HCS08 Instruction Set Summary (Sheet 2 of 7)
Effect
on CCR
Source
Form
Operation
Description
V H I N Z C
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
11 dd
13 dd
15 dd
17 dd
19 dd
1B dd
1D dd
1F dd
5
5
5
5
5
5
5
5
BCLR n,opr8a
Clear Bit n in Memory
Mn ← 0
– – – – – –
Branch if Carry Bit Set
(Same as BLO)
BCS rel
BEQ rel
Branch if (C) = 1
Branch if (Z) = 1
REL
REL
25 rr
27 rr
3
3
– – – – – –
– – – – – –
Branch if Equal
Branch if Greater Than or
Equal To
BGE rel
Branch if (N ⊕ V) = 0
REL
INH
90 rr
82
3
– – – – – –
– – – – – –
(Signed Operands)
Waits For and Processes BDM
Commands Until GO, TRACE1, or
TAGGO
Enter Active Background
if ENBDM = 1
BGND
5+
Branch if Greater Than
(Signed Operands)
BGT rel
Branch if (Z) | (N ⊕ V) = 0
REL
REL
92 rr
28 rr
3
3
– – – – – –
– – – – – –
Branch if Half Carry Bit
Clear
BHCC rel
Branch if (H) = 0
Branch if Half Carry Bit
Set
BHCS rel
BHI rel
Branch if (H) = 1
Branch if (C) | (Z) = 0
Branch if (C) = 0
REL
REL
REL
29 rr
22 rr
24 rr
3
3
3
– – – – – –
– – – – – –
– – – – – –
Branch if Higher
Branch if Higher or Same
(Same as BCC)
BHS rel
BIH rel
BIL rel
Branch if IRQ Pin High
Branch if IRQ Pin Low
Branch if IRQ pin = 1
Branch if IRQ pin = 0
REL
REL
2F rr
2E rr
3
3
– – – – – –
– – – – – –
BIT #opr8i
BIT opr8a
IMM
DIR
EXT
IX2
A5 ii
B5 dd
2
3
4
4
3
3
5
4
BIT opr16a
BIT oprx16,X
BIT oprx8,X
BIT ,X
C5 hh ll
D5 ee ff
E5 ff
(A) & (M)
(CCR Updated but Operands
Not Changed)
Bit Test
↕
↕
–
0 – –
IX1
IX
SP2
SP1
F5
BIT oprx16,SP
BIT oprx8,SP
9ED5 ee ff
9EE5 ff
Branch if Less Than
or Equal To
(Signed Operands)
BLE rel
Branch if (Z) | (N ⊕ V) = 1
REL
93 rr
3
– – – – – –
Branch if Lower
(Same as BCS)
BLO rel
BLS rel
BLT rel
Branch if (C) = 1
Branch if (C) | (Z) = 1
Branch if (N ⊕ V ) = 1
REL
REL
REL
25 rr
23 rr
91 rr
3
3
3
– – – – – –
– – – – – –
– – – – – –
Branch if Lower or Same
Branch if Less Than
(Signed Operands)
Branch if Interrupt Mask
Clear
BMC rel
BMI rel
BMS rel
Branch if (I) = 0
Branch if (N) = 1
Branch if (I) = 1
REL
REL
REL
2C rr
2B rr
2D rr
3
3
3
– – – – – –
– – – – – –
– – – – – –
Branch if Minus
Branch if Interrupt Mask
Set
BNE rel
BPL rel
BRA rel
Branch if Not Equal
Branch if Plus
Branch if (Z) = 0
Branch if (N) = 0
No Test
REL
REL
REL
26 rr
2A rr
20 rr
3
3
3
– – – – – –
– – – – – –
– – – – – –
Branch Always
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
121
Chapter 7 Central Processor Unit (S08CPUV2)
Table 7-2. HCS08 Instruction Set Summary (Sheet 3 of 7)
Effect
on CCR
Source
Form
Operation
Description
V H I N Z C
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
01 dd rr
03 dd rr
05 dd rr
07 dd rr
09 dd rr
0B dd rr
0D dd rr
0F dd rr
5
5
5
5
5
5
5
5
Branch if Bit n in Memory
BRCLR n,opr8a,rel
BRN rel
Branch if (Mn) = 0
Uses 3 Bus Cycles
Branch if (Mn) = 1
↕
– – – – –
Clear
Branch Never
REL
21 rr
3
– – – – – –
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
00 dd rr
02 dd rr
04 dd rr
06 dd rr
08 dd rr
0A dd rr
0C dd rr
0E dd rr
5
5
5
5
5
5
5
5
Branch if Bit n in Memory
Set
BRSET n,opr8a,rel
↕
– – – – –
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
10 dd
12 dd
14 dd
16 dd
18 dd
1A dd
1C dd
1E dd
5
5
5
5
5
5
5
5
BSET n,opr8a
BSR rel
Set Bit n in Memory
Mn ← 1
– – – – – –
PC ← (PC) + 0x0002
push (PCL); SP ← (SP) – 0x0001
push (PCH); SP ← (SP) – 0x0001
PC ← (PC) + rel
Branch to Subroutine
Compare and Branch if
REL
AD rr
5
– – – – – –
CBEQ opr8a,rel
CBEQA #opr8i,rel
CBEQX #opr8i,rel
CBEQ oprx8,X+,rel Equal
CBEQ ,X+,rel
CBEQ oprx8,SP,rel
Branch if (A) = (M)
Branch if (A) = (M)
Branch if (X) = (M)
Branch if (A) = (M)
Branch if (A) = (M)
Branch if (A) = (M)
DIR
IMM
IMM
IX1+
IX+
31 dd rr
41 ii rr
51 ii rr
61 ff rr
71 rr
5
4
4
5
5
6
– – – – – –
SP1
9E61 ff rr
CLC
CLI
Clear Carry Bit
C ← 0
I ← 0
INH
INH
98
9A
1
1
– – – – – 0
– – 0 – – –
Clear Interrupt Mask Bit
Clear
CLR opr8a
CLRA
M ← 0x00
A ← 0x00
X ← 0x00
H ← 0x00
M ← 0x00
M ← 0x00
M ← 0x00
DIR
INH
INH
INH
IX1
IX
3F dd
4F
5
1
1
1
5
4
6
CLRX
CLRH
5F
8C
0 – – 0 1 –
CLR oprx8,X
CLR ,X
6F ff
7F
CLR oprx8,SP
SP1
9E6F ff
CMP #opr8i
CMP opr8a
IMM
DIR
EXT
IX2
A1 ii
B1 dd
2
3
4
4
3
3
5
4
CMP opr16a
CMP oprx16,X
CMP oprx8,X
CMP ,X
C1 hh ll
D1 ee ff
E1 ff
(A) – (M)
(CCR Updated But Operands Not
Changed)
Compare Accumulator
with Memory
↕
– –
↕
↕
↕
IX1
IX
SP2
SP1
F1
CMP oprx16,SP
CMP oprx8,SP
9ED1 ee ff
9EE1 ff
COM opr8a
COMA
M ← (M)= 0xFF – (M)
A ← (A) = 0xFF – (A)
X ← (X) = 0xFF – (X)
M ← (M) = 0xFF – (M)
M ← (M) = 0xFF – (M)
M ← (M) = 0xFF – (M)
DIR
INH
INH
IX1
IX
33 dd
43
5
1
1
5
4
6
COMX
Complement
53
↕
↕
↕
↕
0 – –
1
COM oprx8,X
COM ,X
COM oprx8,SP
(One’s Complement)
63 ff
73
9E63 ff
SP1
CPHX opr16a
CPHX #opr16i
CPHX opr8a
EXT
IMM
DIR
SP1
3E hh ll
65 jj kk
75 dd
6
3
5
6
(H:X) – (M:M + 0x0001)
(CCR Updated But Operands Not
Changed)
Compare Index Register
(H:X) with Memory
↕
↕
– –
CPHX oprx8,SP
9EF3 ff
MC9S08AW60 Data Sheet, Rev 2
122
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
Table 7-2. HCS08 Instruction Set Summary (Sheet 4 of 7)
Effect
on CCR
Source
Form
Operation
Description
V H I N Z C
CPX #opr8i
IMM
DIR
EXT
IX2
A3 ii
B3 dd
2
3
4
4
3
3
5
4
CPX opr8a
CPX opr16a
CPX oprx16,X
CPX oprx8,X
CPX ,X
CPX oprx16,SP
CPX oprx8,SP
C3 hh ll
D3 ee ff
E3 ff
Compare X (Index
Register Low) with
Memory
(X) – (M)
(CCR Updated But Operands Not
Changed)
↕
↕
↕
↕
↕
↕
↕
– –
IX1
IX
SP2
SP1
F3
9ED3 ee ff
9EE3 ff
Decimal Adjust
Accumulator After ADD or
ADC of BCD Values
DAA
(A)
INH
72
1
U – –
10
DBNZ opr8a,rel
DBNZA rel
DIR
INH
INH
IX1
IX
3B dd rr
4B rr
7
4
4
7
6
8
Decrement A, X, or M
Branch if (result) ≠ 0
DBNZX Affects X Not H
DBNZX rel
Decrement and Branch if
Not Zero
5B rr
– – – – – –
DBNZ oprx8,X,rel
DBNZ ,X,rel
DBNZ oprx8,SP,rel
6B ff rr
7B rr
9E6B ff rr
SP1
DEC opr8a
DECA
M ← (M) – 0x01
A ← (A) – 0x01
X ← (X) – 0x01
M ← (M) – 0x01
M ← (M) – 0x01
M ← (M) – 0x01
DIR
INH
INH
IX1
IX
3A dd
4A
5
1
1
5
4
6
DECX
5A
Decrement
Divide
↕
↕
↕
↕
– –
–
DEC oprx8,X
DEC ,X
DEC oprx8,SP
6A ff
7A
9E6A ff
SP1
A ← (H:A)÷(X)
DIV
↕
INH
52
6
– – – –
H ← Remainder
EOR #opr8i
EOR opr8a
IMM
DIR
EXT
IX2
A8 ii
B8 dd
2
3
4
4
3
3
5
4
EOR opr16a
EOR oprx16,X
EOR oprx8,X
EOR ,X
C8 hh ll
D8 ee ff
E8 ff
Exclusive OR
Memory with
Accumulator
A ← (A ⊕ M)
↕
↕
↕
↕
0 – –
–
–
IX1
IX
SP2
SP1
F8
EOR oprx16,SP
EOR oprx8,SP
9ED8 ee ff
9EE8 ff
INC opr8a
INCA
M ← (M) + 0x01
A ← (A) + 0x01
X ← (X) + 0x01
M ← (M) + 0x01
M ← (M) + 0x01
M ← (M) + 0x01
DIR
INH
INH
IX1
IX
3C dd
4C
5
1
1
5
4
6
INCX
5C
Increment
↕
– –
INC oprx8,X
INC ,X
6C ff
7C
INC oprx8,SP
SP1
9E6C ff
JMP opr8a
JMP opr16a
JMP oprx16,X
JMP oprx8,X
JMP ,X
DIR
EXT
IX2
IX1
IX
BC dd
CC hh ll
DC ee ff
EC ff
3
4
4
3
3
Jump
PC ← Jump Address
– – – – – –
FC
JSR opr8a
JSR opr16a
JSR oprx16,X
JSR oprx8,X
JSR ,X
DIR
EXT
IX2
IX1
IX
BD dd
CD hh ll
DD ee ff
ED ff
5
6
6
5
5
PC ← (PC) + n (n = 1, 2, or 3)
Push (PCL); SP ← (SP) – 0x0001
Push (PCH); SP ← (SP) – 0x0001
PC ← Unconditional Address
Jump to Subroutine
– – – – – –
FD
LDA #opr8i
LDA opr8a
IMM
DIR
EXT
IX2
A6 ii
B6 dd
2
3
4
4
3
3
5
4
LDA opr16a
LDA oprx16,X
LDA oprx8,X
LDA ,X
C6 hh ll
D6 ee ff
E6 ff
Load Accumulator from
Memory
A ← (M)
0 – –
↕
↕
↕
↕
–
–
IX1
IX
SP2
SP1
F6
LDA oprx16,SP
LDA oprx8,SP
9ED6 ee ff
9EE6 ff
LDHX #opr16i
LDHX opr8a
LDHX opr16a
LDHX ,X
LDHX oprx16,X
LDHX oprx8,X
LDHX oprx8,SP
IMM
DIR
EXT
IX
IX2
IX1
SP1
45 jj kk
55 dd
32 hh ll
9EAE
9EBE ee ff
9ECE ff
9EFE ff
3
4
5
5
6
5
5
Load Index Register (H:X)
from Memory
H:X ← (M:M + 0x0001)
0 – –
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
123
Chapter 7 Central Processor Unit (S08CPUV2)
Table 7-2. HCS08 Instruction Set Summary (Sheet 5 of 7)
Effect
on CCR
Source
Form
Operation
Description
V H I N Z C
LDX #opr8i
IMM
DIR
EXT
IX2
AE ii
BE dd
2
3
4
4
3
3
5
4
LDX opr8a
LDX opr16a
LDX oprx16,X
LDX oprx8,X
LDX ,X
LDX oprx16,SP
LDX oprx8,SP
CE hh ll
DE ee ff
EE ff
Load X (Index Register
Low) from Memory
X ← (M)
↕
↕
↕
0 – –
–
IX1
IX
SP2
SP1
FE
9EDE ee ff
9EEE ff
LSL opr8a
LSLA
DIR
INH
INH
IX1
IX
38 dd
48
5
1
1
5
4
6
LSLX
Logical Shift Left
(Same as ASL)
58
C
0
↕
↕
↕
– –
LSL oprx8,X
LSL ,X
68 ff
78
b7
b0
b0
LSL oprx8,SP
SP1
9E68 ff
LSR opr8a
LSRA
DIR
INH
INH
IX1
IX
34 dd
44
5
1
1
5
4
6
LSRX
54
0
C
Logical Shift Right
↕
↕
↕
↕
– – 0
LSR oprx8,X
LSR ,X
64 ff
74
b7
LSR oprx8,SP
SP1
9E64 ff
MOV opr8a,opr8a
MOV opr8a,X+
MOV #opr8i,opr8a
MOV ,X+,opr8a
(M)
← (M)
DIR/DIR
DIR/IX+
IMM/DIR
IX+/DIR
4E dd dd
5E dd
6E ii dd
7E dd
5
5
4
5
destination
source
Move
↕
0 – –
–
H:X ← (H:X) + 0x0001 in
IX+/DIR and DIR/IX+ Modes
MUL
Unsigned multiply
X:A ← (X) × (A)
INH
42
5
– 0 – – – 0
NEG opr8a
NEGA
M ← – (M) = 0x00 – (M)
A ← – (A) = 0x00 – (A)
X ← – (X) = 0x00 – (X)
M ← – (M) = 0x00 – (M)
M ← – (M) = 0x00 – (M)
M ← – (M) = 0x00 – (M)
DIR
INH
INH
IX1
IX
30 dd
40
5
1
1
5
4
6
NEGX
Negate
(Two’s Complement)
50
↕
↕
↕
– –
NEG oprx8,X
NEG ,X
NEG oprx8,SP
60 ff
70
9E60 ff
SP1
NOP
No Operation
Uses 1 Bus Cycle
INH
9D
1
– – – – – –
– – – – – –
Nibble Swap
Accumulator
NSA
A ← (A[3:0]:A[7:4])
INH
62
1
ORA #opr8i
ORA opr8a
IMM
DIR
EXT
IX2
AA ii
BA dd
2
3
4
4
3
3
5
4
ORA opr16a
ORA oprx16,X
ORA oprx8,X
ORA ,X
CA hh ll
DA ee ff
EA ff
InclusiveORAccumulator
and Memory
A ← (A) | (M)
↕
↕
–
0 – –
IX1
IX
SP2
SP1
FA
ORA oprx16,SP
ORA oprx8,SP
9EDA ee ff
9EEA ff
Push Accumulator onto
Stack
PSHA
PSHH
PSHX
PULA
PULH
PULX
Push (A); SP ← (SP) – 0x0001
Push (H); SP ← (SP) – 0x0001
Push (X); SP ← (SP) – 0x0001
SP ← (SP + 0x0001); Pull (A)
SP ← (SP + 0x0001); Pull (H)
SP ← (SP + 0x0001); Pull (X)
INH
INH
INH
INH
INH
INH
87
8B
89
86
8A
88
2
2
2
3
3
3
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
Push H (Index Register
High) onto Stack
Push X (Index Register
Low) onto Stack
Pull Accumulator from
Stack
Pull H (Index Register
High) from Stack
Pull X (Index Register
Low) from Stack
ROL opr8a
ROLA
DIR
INH
INH
IX1
IX
39 dd
49
5
1
1
5
4
6
ROLX
59
C
Rotate Left through Carry
↕
↕
↕
↕
– –
ROL oprx8,X
ROL ,X
ROL oprx8,SP
69 ff
79
9E69 ff
b7
b0
SP1
MC9S08AW60 Data Sheet, Rev 2
124
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
Table 7-2. HCS08 Instruction Set Summary (Sheet 6 of 7)
Effect
on CCR
Source
Form
Operation
Description
V H I N Z C
ROR opr8a
DIR
INH
INH
IX1
IX
36 dd
46
5
1
1
5
4
6
RORA
RORX
Rotate Right through
Carry
56
C
↕
↕
↕
↕
– –
ROR oprx8,X
ROR ,X
66 ff
76
9E66 ff
b7
b0
ROR oprx8,SP
SP1
SP ← 0xFF
RSP
Reset Stack Pointer
Return from Interrupt
Return from Subroutine
INH
INH
INH
9C
80
81
1
9
6
– – – – – –
(High Byte Not Affected)
SP ← (SP) + 0x0001; Pull (CCR)
SP ← (SP) + 0x0001; Pull (A)
SP ← (SP) + 0x0001; Pull (X)
SP ← (SP) + 0x0001; Pull (PCH)
SP ← (SP) + 0x0001; Pull (PCL)
SP ← SP + 0x0001; Pull (PCH)
SP ← SP + 0x0001; Pull (PCL)
RTI
↕
↕
↕
↕
↕
↕
RTS
– – – – – –
SBC #opr8i
SBC opr8a
IMM
DIR
EXT
IX2
A2 ii
2
3
4
4
3
3
5
4
B2 dd
SBC opr16a
SBC oprx16,X
SBC oprx8,X
SBC ,X
C2 hh ll
D2 ee ff
E2 ff
Subtract with Carry
A ← (A) – (M) – (C)
↕
↕
↕
↕
– –
IX1
IX
SP2
SP1
F2
SBC oprx16,SP
SBC oprx8,SP
9ED2 ee ff
9EE2 ff
SEC
SEI
Set Carry Bit
C ← 1
I ← 1
INH
INH
99
9B
1
1
– – – – – 1
– – 1 – – –
Set Interrupt Mask Bit
STA opr8a
DIR
EXT
IX2
IX1
IX
B7 dd
C7 hh ll
D7 ee ff
E7 ff
3
4
4
3
2
5
4
STA opr16a
STA oprx16,X
STA oprx8,X
STA ,X
Store Accumulator in
Memory
M ← (A)
↕
↕
↕
↕
0 – –
–
–
F7
STA oprx16,SP
STA oprx8,SP
SP2
SP1
9ED7 ee ff
9EE7 ff
STHX opr8a
STHX opr16a
STHX oprx8,SP
DIR
EXT
SP1
35 dd
96 hh ll
9EFF ff
4
5
5
Store H:X (Index Reg.)
(M:M + 0x0001) ← (H:X)
I bit ← 0; Stop Processing
0 – –
Enable Interrupts:
Stop Processing
Refer to MCU
STOP
INH
8E
2+
– – 0 – – –
Documentation
STX opr8a
DIR
EXT
IX2
IX1
IX
BF dd
CF hh ll
DF ee ff
EF ff
3
4
4
3
2
5
4
STX opr16a
STX oprx16,X
STX oprx8,X
STX ,X
Store X (Low 8 Bits of
Index Register)
in Memory
M ← (X)
↕
↕
↕
↕
0 – –
–
FF
STX oprx16,SP
STX oprx8,SP
SP2
SP1
9EDF ee ff
9EEF ff
SUB #opr8i
SUB opr8a
IMM
DIR
EXT
IX2
A0 ii
B0 dd
2
3
4
4
3
3
5
4
SUB opr16a
SUB oprx16,X
SUB oprx8,X
SUB ,X
C0 hh ll
D0 ee ff
E0 ff
Subtract
A ← (A) – (M)
↕
↕
– –
IX1
IX
F0
SUB oprx16,SP
SUB oprx8,SP
SP2
SP1
9ED0 ee ff
9EE0 ff
PC ← (PC) + 0x0001
Push (PCL); SP ← (SP) – 0x0001
Push (PCH); SP ← (SP) – 0x0001
Push (X); SP ← (SP) – 0x0001
Push (A); SP ← (SP) – 0x0001
Push (CCR); SP ← (SP) – 0x0001
I ← 1;
SWI
Software Interrupt
INH
83
11
– – 1 – – –
PCH ← Interrupt Vector High Byte
PCL ← Interrupt Vector Low Byte
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
125
Chapter 7 Central Processor Unit (S08CPUV2)
Table 7-2. HCS08 Instruction Set Summary (Sheet 7 of 7)
Effect
on CCR
Source
Form
Operation
Description
V H I N Z C
Transfer Accumulator to
CCR
TAP
TAX
TPA
CCR ← (A)
X ← (A)
↕
↕
↕
↕
↕
↕
INH
INH
INH
84
97
85
1
1
1
Transfer Accumulator to
X (Index Register Low)
– – – – – –
– – – – – –
Transfer CCR to
Accumulator
A ← (CCR)
TST opr8a
TSTA
(M) – 0x00
(A) – 0x00
(X) – 0x00
(M) – 0x00
(M) – 0x00
(M) – 0x00
DIR
INH
INH
IX1
IX
3D dd
4D
4
1
1
4
3
5
TSTX
5D
Test for Negative or Zero
↕
↕
–
0 – –
TST oprx8,X
TST ,X
TST oprx8,SP
6D ff
7D
9E6D ff
SP1
TSX
TXA
TXS
WAIT
Transfer SP to Index Reg.
H:X ← (SP) + 0x0001
A ← (X)
INH
INH
INH
INH
95
9F
94
8F
2
– – – – – –
– – – – – –
– – – – – –
– – 0 – – –
Transfer X (Index Reg.
Low) to Accumulator
1
Transfer Index Reg. to SP
SP ← (H:X) – 0x0001
I bit ← 0; Halt CPU
2
Enable Interrupts; Wait
for Interrupt
2+
1
Bus clock frequency is one-half of the CPU clock frequency.
MC9S08AW60 Data Sheet, Rev 2
126
Freescale Semiconductor
Chapter 7 Central Processor Unit (S08CPUV2)
Table 7-3. Opcode Map (Sheet 1 of 2)
Bit-Manipulation
10
Branch
20
Read-Modify-Write
Control
Register/Memory
00
5
5
3
30
5
40
1
50
1
60
5
70
4
80
9
90
3
A0
2
B0
3
C0
4
D0
4
E0
3
3
BRSET0 BSET0
BRA
NEG
NEGA
NEGX
NEG
NEG
RTI
BGE
SUB
SUB
SUB
SUB
SUB
3
01
DIR
5
2
11
DIR
5
2
21
REL
3
2
DIR
5
1
INH
4
1
INH
4
2
IX1
5
1
IX
5
1
81
INH
6
2
91
REL
3
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
IX
3
31
41
51
61
71
A1
B1
C1
D1
E1
BRCLR0 BCLR0
BRN
CBEQ CBEQA CBEQX CBEQ
CBEQ
RTS
BLT
CMP
CMP
CMP
CMP
CMP
CMP
3
DIR
5
2
DIR
5
2
22
REL
3
3
DIR
5
3
IMM
5
3
IMM
6
3
IX1+
1
2
IX+
1
1
82
INH
2
REL
3
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
02
12
32
42
52
62
72
5+ 92
A2
B2
C2
D2
E2
F2
BRSET1 BSET1
BHI
LDHX
MUL
DIV
NSA
DAA
BGND
BGT
SBC
SBC
SBC
SBC
SBC
SBC
3
DIR
5
2
DIR
5
2
23
REL
3
3
EXT
5
1
43
INH
1
1
53
INH
1
1
63
INH
5
1
73
INH
4
1
INH
2
REL
3
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
03
13
33
83
11 93
A3
B3
C3
D3
E3
F3
BRCLR1 BCLR1
BLS
COM
COMA
COMX
COM
COM
SWI
BLE
CPX
CPX
CPX
CPX
CPX
CPX
3
DIR
5
2
DIR
5
2
24
REL
3
2
DIR
5
1
INH
1
INH
2
IX1
5
1
IX
4
1
84
INH
1
2
94
REL
2
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
04
14
34
44
1
54
1
64
74
A4
B4
C4
D4
E4
F4
BRSET2 BSET2
BCC
LSR
LSRA
LSRX
LSR
LSR
TAP
TXS
AND
AND
AND
AND
AND
AND
3
DIR
5
2
DIR
5
2
25
REL
3
2
35
DIR
4
1
INH
3
1
INH
4
2
65
IX1
3
1
75
IX
5
1
85
INH
1
1
95
INH
2
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
05
15
45
55
A5
B5
C5
D5
E5
F5
BRCLR2 BCLR2
BCS
STHX
LDHX
LDHX
CPHX
CPHX
TPA
TSX
BIT
BIT
BIT
BIT
BIT
BIT
LDA
STA
3
DIR
5
2
DIR
5
2
26
REL
3
2
DIR
5
3
IMM
1
2
DIR
1
3
IMM
5
2
DIR
4
1
86
INH
3
1
96
INH
5
2
A6
IMM
2
2
B6
DIR
3
3
C6
EXT
4
3
D6
IX2
4
2
E6
IX1
3
1
F6
IX
3
06
16
36
ROR
46
56
66
ROR
76
ROR
BRSET3 BSET3
BNE
RORA
RORX
PULA
STHX
LDA
LDA
LDA
LDA
LDA
3
07
DIR
5
2
17
DIR
5
2
27
REL
3
2
DIR
5
1
INH
1
INH
2
IX1
5
1
IX
4
1
87
INH
2
3
97
EXT
1
2
A7
IMM
2
2
B7
DIR
3
3
C7
EXT
4
3
D7
IX2
4
2
E7
IX1
3
1
F7
IX
2
37
47
1
57
1
67
77
BRCLR3 BCLR3
BEQ
ASR
ASRA
ASRX
ASR
ASR
PSHA
TAX
AIS
STA
STA
STA
STA
3
08
DIR
5
2
18
DIR
5
2
28
REL
3
2
DIR
5
1
INH
1
1
INH
1
2
IX1
5
1
IX
4
1
88
INH
3
1
98
INH
1
2
A8
IMM
2
2
B8
DIR
3
3
C8
EXT
4
3
D8
IX2
4
2
E8
IX1
3
1
F8
IX
3
38
48
58
68
78
BRSET4 BSET4
BHCC
LSL
LSLA
LSLX
LSL
LSL
PULX
CLC
EOR
EOR
EOR
EOR
EOR
EOR
3
DIR
5
2
DIR
5
2
REL
2
39
DIR
5
1
INH
1
1
INH
1
2
69
IX1
5
1
79
IX
4
1
INH
2
1
99
INH
1
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
09
19
29
3
49
59
89
A9
B9
C9
D9
E9
F9
BRCLR4 BCLR4
BHCS
ROL
ROLA
ROLX
ROL
ROL
PSHX
SEC
ADC
ADC
ADC
ADC
ADC
ADC
3
DIR
5
2
DIR
5
2
REL
3
2
DIR
5
1
INH
1
1
INH
1
2
IX1
5
1
IX
4
1
INH
3
1
INH
1
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
0A
1A
2A
3A
4A
5A
6A
7A
8A
9A
AA
BA
CA
DA
EA
FA
BRSET5 BSET5
BPL
DEC
DECA
DECX
DEC
DEC
PULH
CLI
ORA
ORA
ORA
ORA
ORA
ORA
3
DIR
5
2
DIR
5
2
2B
REL
3
2
DIR
7
1
INH
1
INH
2
IX1
7
1
IX
6
1
INH
2
1
9B
INH
1
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
0B
1B
3B
4B
4
5B
4
6B
7B
8B
AB
BB
CB
DB
EB
FB
BRCLR5 BCLR5
BMI
DBNZ
DBNZA DBNZX
DBNZ
DBNZ
PSHH
SEI
ADD
ADD
ADD
ADD
ADD
ADD
3
DIR
5
2
DIR
5
2
2C
REL
3
3
DIR
5
2
INH
1
2
INH
1
3
IX1
5
2
IX
4
1
INH
1
9C
INH
1
2
IMM
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
0C
1C
3C
4C
5C
6C
7C
8C
1
BC
CC
DC
EC
FC
BRSET6 BSET6
BMC
INC
INCA
INCX
INC
INC
CLRH
RSP
JMP
JMP
JMP
JMP
JMP
3
DIR
5
2
DIR
5
2
REL
3
2
3D
DIR
4
1
INH
1
1
INH
1
2
6D
IX1
4
1
7D
IX
3
1
INH
1
INH
1
2
DIR
5
3
EXT
6
3
IX2
6
2
IX1
5
1
IX
5
0D
1D
2D
4D
5D
9D
AD
5
BD
CD
DD
ED
FD
BRCLR6 BCLR6
BMS
TST
TSTA
TSTX
TST
TST
NOP
BSR
JSR
JSR
JSR
JSR
JSR
3
DIR
5
2
DIR
5
2
REL
3
2
3E
DIR
6
1
INH
5
1
INH
5
2
6E
IX1
4
1
7E
IX
5
1
INH
2
REL
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
IX
3
0E
1E
2E
4E
5E
8E
2+ 9E
AE
BE
CE
DE
EE
FE
BRSET7 BSET7
BIL
CPHX
MOV
MOV
MOV
MOV
STOP
Page 2
LDX
LDX
LDX
LDX
LDX
LDX
3
DIR
5
2
DIR
5
2
2F
REL
3
3
EXT
3
DD
1
2
DIX+
1
3
IMD
5
2
IX+D
4
1
INH
2
IMM
2
2
DIR
3
3
EXT
4
3
IX2
4
2
IX1
3
1
FF
IX
2
0F
1F
3F
5
4F
5F
6F
7F
1
8F
2+ 9F
1
AF
BF
STX
CF
STX
DF
STX
EF
STX
BRCLR7 BCLR7
BIH
CLR
CLRA
CLRX
CLR
CLR
WAIT
TXA
AIX
STX
3
DIR
2
DIR
2
REL
2
DIR
1
INH
1
INH
2
IX1
IX
1
INH
1
INH
2
IMM
2
DIR
3
EXT
3
IX2
2
IX1
1
IX
INH
IMM
DIR
EXT
DD
Inherent
REL
IX
Relative
SP1
SP2
IX+
Stack Pointer, 8-Bit Offset
Stack Pointer, 16-Bit Offset
Indexed, No Offset with
Post Increment
Indexed, 1-Byte Offset with
Post Increment
Immediate
Direct
Indexed, No Offset
IX1
IX2
IMD
Indexed, 8-Bit Offset
Indexed, 16-Bit Offset
IMM to DIR
Extended
DIR to DIR
IX+D IX+ to DIR
IX1+
DIX+ DIR to IX+
Opcode in
F0
3
HCS08 Cycles
Instruction Mnemonic
Addressing Mode
Hexadecimal
SUB
Number of Bytes
1
IX
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
127
Chapter 7 Central Processor Unit (S08CPUV2)
Table 7-3. Opcode Map (Sheet 2 of 2)
Bit-Manipulation
Branch
Read-Modify-Write
9E60
Control
Register/Memory
6
9ED0
SUB
5
9EE0
4
NEG
SUB
3
SP1
6
4
SP2
5
3
SP1
4
9E61
9ED1
9EE1
CBEQ
CMP
CMP
4
SP1
4
SP2
5
3
SP1
4
9ED2
9EE2
SBC
SBC
4
SP2
5
3
SP1
4
9E63
6
9ED3
9EE3
9EF3
6
COM
CPX
CPX
CPHX
3
SP1
6
4
SP2
5
3
SP1
4
3
SP1
9E64
9ED4
9EE4
LSR
AND
AND
3
SP1
4
SP2
5
3
SP1
4
9ED5
9EE5
BIT
BIT
4
SP2
5
3
SP1
4
9E66
6
9ED6
9EE6
ROR
LDA
LDA
3
SP1
6
4
SP2
5
3
SP1
4
9E67
9ED7
9EE7
ASR
STA
STA
3
SP1
6
4
SP2
5
3
SP1
4
9E68
9ED8
9EE8
LSL
EOR
EOR
3
SP1
6
4
SP2
5
3
SP1
4
9E69
9ED9
9EE9
ROL
ADC
ADC
3
SP1
6
4
SP2
5
3
SP1
4
9E6A
9EDA
9EEA
DEC
ORA
ORA
3
SP1
8
4
SP2
5
3
SP1
4
9E6B
9EDB
9EEB
DBNZ
ADD
ADD
4
SP1
4
SP2
3
SP1
9E6C
6
INC
3
SP1
5
9E6D
TST
3
SP1
5
9EBE
6
5
5
4
5
LDHX
IX
4
IX2
IX1
SP1
5
9E6F
6
CLR
STX
STX
STHX
3
SP1
4
SP2
3
SP1
3
SP1
INH
Inherent
Immediate
Direct
REL
IX
Relative
SP1
SP2
IX+
Stack Pointer, 8-Bit Offset
Stack Pointer, 16-Bit Offset
Indexed, No Offset with
Post Increment
Indexed, 1-Byte Offset with
Post Increment
IMM
DIR
EXT
DD
Indexed, No Offset
Indexed, 8-Bit Offset
Indexed, 16-Bit Offset
IMM to DIR
IX1
IX2
IMD
Extended
DIR to DIR
IX1+
IX+D IX+ to DIR
DIX+ DIR to IX+
Note: All Sheet 2 Opcodes are Preceded by the Page 2 Prebyte (9E)
Prebyte (9E) and Opcode in
Hexadecimal
9E60
3
6
HCS08 Cycles
Instruction Mnemonic
Addressing Mode
NEG
Number of Bytes
SP1
MC9S08AW60 Data Sheet, Rev 2
128
Freescale Semiconductor
Chapter 8
Internal Clock Generator (S08ICGV4)
The internal clock generation (ICG) module is used to generate the system clocks for the MC9S08AW60
Series MCU. The analog supply lines V
and V
are internally derived from the MCU’s V and
DDA
SSA DD
V
pins. Electrical parametric data for the ICG may be found in Appendix A, “Electrical Characteristics
SS
and Timing Specifications.”
SYSTEM
CONTROL
LOGIC
TPM1
TPM2
IIC1
SCI1
SCI2
SPI1
ICGERCLK
RTI
FFE
÷2
ICG
FIXED FREQ CLOCK (XCLK)
BUSCLK
ICGOUT
÷2
ICGLCLK*
CPU
BDC
RAM
FLASH
ADC
ADC has min and max
frequency requirements.
See Chapter 14,
FLASH has frequency
requirements for program
and erase operation.
* ICGLCLK is the alternate BDC clock source for the MC9S08AW60 Series.
“Analog-to-Digital Converter
(S08ADC10V1) and
See Appendix A, “Electrical
Characteristics and Timing
Specifications.
Appendix A, “Electrical
Characteristics and Timing
Specifications
Figure 8-1. System Clock Distribution Diagram
NOTE
Freescale Semiconductor recommends that FLASH location $FFBE be
reserved to store a nonvolatile version of ICGTRM. This will allow
debugger and programmer vendors to perform a manual trim operation and
store the resultant ICGTRM value for users to access at a later time.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
129
Chapter 8 Internal Clock Generator (S08ICGV4)
HCS08 CORE
DEBUG
MODULE (DBG)
8
PTA7– PTA0
BKGD/MS
BDC
CPU
8
PTB7/AD1P7–
PTB0/AD1P0
HCS08 SYSTEM CONTROL
RESET
IRQ
PTC6
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
RxD2
TxD2
PTC5/RxD2
PTC4
PTC3/TxD2
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI2)
PTC2/MCLK
PTC1/SDA1
SDA1
SCL1
RTI
COP
LVD
IIC MODULE (IIC1)
PTC0/SCL1
IRQ
AD1P7–AD1P0
8
V
DDAD
8
10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC1)
AD1P15–AD1P8
V
SSAD
V
REFL
PTD7/AD1P15/KBI1P7
PTD6/AD1P14/TPM1CLK
PTD5/AD1P13
PTD4/AD1P12/TPM2CLK
PTD3/AD1P11/KBI1P6
PTD2/AD1P10/KBI1P5
PTD1/AD1P9
V
REFH
USER FLASH
(AW60 = 63,280 BYTES)
(AW48 = 49,152 BYTES)
(AW32 = 32,768 BYTES)
(AW16 = 16,384 BYTES)
PTD0/AD1P8
SPSCK1
PTE7/SPSCK1
PTE6/MOSI1
MOSI1
SERIAL PERIPHERAL
USER RAM
MISO1
SS1
INTERFACE MODULE (SPI1)
PTE5/MISO1
PTE4/SS1
AW60/48/32 = 2048 BYTES
AW16 = 1024 BYTES
TPM1CLK
PTE3/TPM1CH1
PTE2/TPM1CH0
6-CHANNEL TIMER/PWM
MODULE (TPM1)
TPM1CH5–
TPM1CH0
INTERNAL CLOCK
GENERATOR (ICG)
6
RxD1
TxD1
PTE1/RxD1
PTE0/TxD1
PTF7
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI1)
LOW-POWER OSCILLATOR
PTF6
PTF5/TPM2CH1
PTF4/TPM2CH0
TPM2CLK
V
DD
VOLTAGE
REGULATOR
2-CHANNEL TIMER/PWM
MODULE (TPM2)
TPM2CH1–TPM2CH0
V
SS
2
PTF3/TPM1CH5
KBI1P7–KBI1P5
3
PTF2/TPM1CH4
PTF1/TPM1CH3
PTF0/TPM1CH2
8-BIT KEYBOARD
INTERRUPT MODULE (KBI1)
KBI1P4–KBI1P0
5
EXTAL
XTAL
PTG6/EXTAL
PTG5/XTAL
NOTES:
PTG4/KBI1P4
PTG3/KBI1P3
PTG2/KBI1P2
PTG1/KBI1P1
PTG0/KBI1P0
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software configurable pullup/pulldown device if IRQ is enabled
(IRQPE = 1). Pulldown is enabled if rising edge detect is selected (IRQEDG = 1)
3. IRQ does not have a clamp diode to VDD. IRQ should not be driven above VDD
4. Pin contains integrated pullup device.
.
5. Pins PTD7, PTD3, PTD2, and PTG4 contain both pullup and pulldown devices.
Pulldown enabled when KBI is enabled (KBIPEn = 1) and rising edge is selected
(KBEDGn = 1).
Figure 8-2. Block Diagram Highlighting ICG Module
MC9S08AW60 Data Sheet, Rev 2
130
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.1
Introduction
The ICG provides multiple options for clock sources. This offers a user great flexibility when making
choices between cost, precision, current draw, and performance. As seen in Figure 8-3, the ICG consists
of four functional blocks. Each of these is briefly described here and then in more detail in a later section.
•
Oscillator block — The oscillator block provides means for connecting an external crystal or
resonator. Two frequency ranges are software selectable to allow optimal startup and stability.
Alternatively, the oscillator block can be used to route an external square wave to the system clock.
External sources can provide a very precise clock source. The oscillator is capable of being
configured for low power mode or high amplitude mode as selected by HGO.
•
Internal reference generator — The internal reference generator consists of two controlled clock
sources. One is designed to be approximately 8 MHz and can be selected as a local clock for the
background debug controller. The other internal reference clock source is typically 243 kHz and
can be trimmed for finer accuracy via software when a precise timed event is input to the MCU.
This provides a highly reliable, low-cost clock source.
•
•
Frequency-locked loop — A frequency-locked loop (FLL) stage takes either the internal or
external clock source and multiplies it to a higher frequency. Status bits provide information when
the circuit has achieved lock and when it falls out of lock. Additionally, this block can monitor the
external reference clock and signals whether the clock is valid or not.
Clock select block — The clock select block provides several switch options for connecting
different clock sources to the system clock tree. ICGDCLK is the multiplied clock frequency out
of the FLL, ICGERCLK is the reference clock frequency from the crystal or external clock source,
and FFE (fixed frequency enable) is a control signal used to control the system fixed frequency
clock (XCLK). ICGLCLK is the clock source for the background debug controller (BDC).
8.1.1
Features
The module is intended to be very user friendly with many of the features occurring automatically without
user intervention. To quickly configure the module, go to Section 8.5, “Initialization/Application
Information” and pick an example that best suits the application needs.
Features of the ICG and clock distribution system:
•
Several options for the primary clock source allow a wide range of cost, frequency, and precision
choices:
— 32 kHz–100 kHz crystal or resonator
— 1 MHz–16 MHz crystal or resonator
— External clock
— Internal reference generator
•
•
Defaults to self-clocked mode to minimize startup delays
Frequency-locked loop (FLL) generates 8 MHz to 40 MHz (for bus rates up to 20 MHz)
— Uses external or internal clock as reference frequency
Automatic lockout of non-running clock sources
Reset or interrupt on loss of clock or loss of FLL lock
•
•
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
131
Chapter 8 Internal Clock Generator (S08ICGV4)
•
Digitally-controlled oscillator (DCO) preserves previous frequency settings, allowing fast
frequency lock when recovering from stop3 mode
•
•
•
•
DCO will maintain operating frequency during a loss or removal of reference clock
Post-FLL divider selects 1 of 8 bus rate divisors (/1 through /128)
Separate self-clocked source for real-time interrupt
Trimmable internal clock source supports SCI communications without additional external
components
•
•
Automatic FLL engagement after lock is acquired
External oscillator selectable for low power or high gain
8.1.2
Modes of Operation
This is a high-level description only. Detailed descriptions of operating modes are contained in
Section 8.4, “Functional Description.”
•
•
•
Mode 1 — Off
The output clock, ICGOUT, is static. This mode may be entered when the STOP instruction is
executed.
Mode 2 — Self-clocked (SCM)
Default mode of operation that is entered immediately after reset. The ICG’s FLL is open loop and
the digitally controlled oscillator (DCO) is free running at a frequency set by the filter bits.
Mode 3 — FLL engaged internal (FEI)
In this mode, the ICG’s FLL is used to create frequencies that are programmable multiples of the
internal reference clock.
— FLL engaged internal unlocked is a transition state that occurs while the FLL is attempting to
lock. The FLL DCO frequency is off target and the FLL is adjusting the DCO to match the
target frequency.
— FLL engaged internal locked is a state that occurs when the FLL detects that the DCO is locked
to a multiple of the internal reference.
•
•
Mode 4 — FLL bypassed external (FBE)
In this mode, the ICG is configured to bypass the FLL and use an external clock as the clock source.
Mode 5 — FLL engaged external (FEE)
The ICG’s FLL is used to generate frequencies that are programmable multiples of the external
clock reference.
— FLL engaged external unlocked is a transition state that occurs while the FLL is attempting to
lock. The FLL DCO frequency is off target and the FLL is adjusting the DCO to match the
target frequency.
— FLL engaged external locked is a state which occurs when the FLL detects that the DCO is
locked to a multiple of the internal reference.
MC9S08AW60 Data Sheet, Rev 2
132
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.1.3
Block Diagram
Figure 8-3 is a top-level diagram that shows the functional organization of the internal clock generation
(ICG) module. This section includes a general description and a feature list.
EXTAL
ICG
OSCILLATOR (OSC)
CLOCK
WITH EXTERNAL REF
SELECT
SELECT
ICGERCLK
OUTPUT
XTAL
CLOCK
ICGDCLK
/R
FREQUENCY
LOCKED
SELECT
DCO
ICGOUT
REF
LOOP (FLL)
SELECT
V
DDA
(SEE NOTE 2)
LOSS OF LOCK
AND CLOCK DETECTOR
V
SSA
(SEE NOTE 2)
FIXED
CLOCK
SELECT
FFE
IRG
TYP 243 kHz
ICGIRCLK
INTERNAL
REFERENCE
8 MHz
RG
LOCAL CLOCK FOR OPTIONAL USE WITH BDC
GENERATORS
ICGLCLK
NOTES:
1. See Table 8-9 for specific use of ICGOUT, FFE, ICGLCLK, ICGERCLK
2. Not all HCS08 microcontrollers have unique supply pins for the ICG. See the device pin assignments.
Figure 8-3. ICG Block Diagram
8.2
External Signal Description
The oscillator pins are used to provide an external clock source for the MCU. The oscillator pins are gain
controlled in low-power mode (default). Oscillator amplitudes in low-power mode are limited to
approximately 1 V, peak-to-peak.
8.2.1
EXTAL — External Reference Clock / Oscillator Input
If upon the first write to ICGC1, either the FEE mode or FBE mode is selected, this pin functions as either
the external clock input or the input of the oscillator circuit as determined by REFS. If upon the first write
to ICGC1, either the FEI mode or SCM mode is selected, this pin is not used by the ICG.
8.2.2
XTAL — Oscillator Output
If upon the first write to ICGC1, either the FEE mode or FBE mode is selected, this pin functions as the
output of the oscillator circuit. If upon the first write to ICGC1, either the FEI mode or SCM mode is
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
133
Chapter 8 Internal Clock Generator (S08ICGV4)
selected, this pin is not used by the ICG. The oscillator is capable of being configured to provide a higher
amplitude output for improved noise immunity. This mode of operation is selected by HGO = 1.
8.2.3
External Clock Connections
If an external clock is used, then the pins are connected as shown Figure 8-4.
ICG
EXTAL
XTAL
V
SS
NOT CONNECTED
CLOCK INPUT
Figure 8-4. External Clock Connections
8.2.4
External Crystal/Resonator Connections
If an external crystal/resonator frequency reference is used, then the pins are connected as shown in
Figure 8-5. Recommended component values are listed in the Electrical Characteristics chapter.
ICG
EXTAL
V
XTAL
SS
R
S
C
C
2
1
R
F
CRYSTAL OR RESONATOR
Figure 8-5. External Frequency Reference Connection
MC9S08AW60 Data Sheet, Rev 2
134
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.3
Register Definition
Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address
assignments for all ICG registers. This section refers to registers and control bits only by their names. A
Freescale-provided equate or header file is used to translate these names into the appropriate absolute
addresses.
8.3.1
ICG Control Register 1 (ICGC1)
7
6
5
4
3
2
1
0
R
0
HGO1
RANGE
REFS
CLKS
OSCSTEN
LOCD
W
Reset
0
1
0
0
0
1
0
0
= Unimplemented or Reserved
Figure 8-6. ICG Control Register 1 (ICGC1)
1
This bit can be written only once after reset. Additional writes are ignored.
Table 8-1. ICGC1 Register Field Descriptions
Field
Description
7
High Gain Oscillator Select — The HGO bit is used to select between low power operation and high gain
HGO
operation for improved noise immunity. This bit is write-once after reset.
0
1
Oscillator configured for low power operation.
Oscillator configured for high gain operation.
6
Frequency Range Select — The RANGE bit controls the oscillator, reference divider, and FLL loop prescaler
multiplication factor (P). It selects one of two reference frequency ranges for the ICG. The RANGE bit is
write-once after a reset. The RANGE bit only has an effect in FLL engaged external and FLL bypassed external
modes.
RANGE
0
1
Oscillator configured for low frequency range. FLL loop prescale factor P is 64.
Oscillator configured for high frequency range. FLL loop prescale factor P is 1.
5
External Reference Select — The REFS bit controls the external reference clock source for ICGERCLK. The
REFS
REFS bit is write-once after a reset.
0
1
External clock requested.
Oscillator using crystal or resonator requested.
4:3
CLKS
Clock Mode Select — The CLKS bits control the clock mode as described below. If FLL bypassed external is
requested, it will not be selected until ERCS = 1. If the ICG enters off mode, the CLKS bits will remain
unchanged. Writes to the CLKS bits will not take effect if a previous write is not complete.
00 Self-clocked
01 FLL engaged, internal reference
10 FLL bypassed, external reference
11 FLL engaged, external reference
The CLKS bits are writable at any time, unless the first write after a reset was CLKS = 0X, the CLKS bits cannot
be written to 1X until after the next reset (because the EXTAL pin was not reserved).
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
135
Chapter 8 Internal Clock Generator (S08ICGV4)
Table 8-1. ICGC1 Register Field Descriptions (continued)
Field
Description
2
Enable Oscillator in Off Mode — The OSCSTEN bit controls whether or not the oscillator circuit remains
OSCSTEN enabled when the ICG enters off mode. This bit has no effect if HGO = 1 and RANGE = 1.
0
1
Oscillator disabled when ICG is in off mode unless ENABLE is high, CLKS = 10, and REFST = 1.
Oscillator enabled when ICG is in off mode, CLKS = 1X and REFST = 1.
1
Loss of Clock Disable
LOCD
0
Loss of clock detection enabled.
1
Loss of clock detection disabled.
MC9S08AW60 Data Sheet, Rev 2
136
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.3.2
ICG Control Register 2 (ICGC2)
7
6
5
4
3
2
1
0
R
LOLRE
MFD
LOCRE
RFD
W
Reset
0
0
0
0
0
0
0
0
Figure 8-7. ICG Control Register 2 (ICGC2)
Table 8-2. ICGC2 Register Field Descriptions
Description
Field
7
Loss of Lock Reset Enable — The LOLRE bit determines what type of request is made by the ICG following a
LOLRE
loss of lock indication. The LOLRE bit only has an effect when LOLS is set.
0
1
Generate an interrupt request on loss of lock.
Generate a reset request on loss of lock.
6:4
MFD
Multiplication Factor — The MFD bits control the programmable multiplication factor in the FLL loop. The value
specified by the MFD bits establishes the multiplication factor (N) applied to the reference frequency. Writes to
the MFD bits will not take effect if a previous write is not complete. Select a low enough value for N such that
fICGDCLK does not exceed its maximum specified value.
000 Multiplication factor = 4
001 Multiplication factor = 6
010 Multiplication factor = 8
011 Multiplication factor = 10
100 Multiplication factor = 12
101 Multiplication factor = 14
110 Multiplication factor = 16
111 Multiplication factor = 18
3
Loss of Clock Reset Enable — The LOCRE bit determines how the system manages a loss of clock condition.
LOCRE
0
Generate an interrupt request on loss of clock.
1
Generate a reset request on loss of clock.
2:0
Reduced Frequency Divider — The RFD bits control the value of the divider following the clock select circuitry.
RFD
The value specified by the RFD bits establishes the division factor (R) applied to the selected output clock source.
Writes to the RFD bits will not take effect if a previous write is not complete.
000 Division factor = 1
001 Division factor = 2
010 Division factor = 4
011 Division factor = 8
100 Division factor = 16
101 Division factor = 32
110 Division factor = 64
111 Division factor = 128
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
137
Chapter 8 Internal Clock Generator (S08ICGV4)
8.3.3
ICG Status Register 1 (ICGS1)
7
6
5
4
3
2
1
0
R
CLKST
REFST
LOLS
LOCK
LOCS
ERCS
ICGIF
W
1
0
Reset
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 8-8. ICG Status Register 1 (ICGS1)
Table 8-3. ICGS1 Register Field Descriptions
Description
Field
7:6
CLKST
Clock Mode Status — The CLKST bits indicate the current clock mode. The CLKST bits don’t update
immediately after a write to the CLKS bits due to internal synchronization between clock domains.
00 Self-clocked
01 FLL engaged, internal reference
10 FLL bypassed, external reference
11 FLL engaged, external reference
5
Reference Clock Status — The REFST bit indicates which clock reference is currently selected by the
REFST
Reference Select circuit.
0
1
External Clock selected.
Crystal/Resonator selected.
4
FLL Loss of Lock Status — The LOLS bit is an indication of FLL lock status.
LOLS
0
FLL has not unexpectedly lost lock since LOLS was last cleared.
1
FLL has unexpectedly lost lock since LOLS was last cleared, LOLRE determines action taken.
3
FLL Lock Status — The LOCK bit indicates whether the FLL has acquired lock. The LOCK bit is cleared in off,
LOCK
self-clocked, and FLL bypassed modes.
0
1
FLL is currently unlocked.
FLL is currently locked.
2
Loss Of Clock Status — The LOCS bit is an indication of ICG loss of clock status.
LOCS
0
ICG has not lost clock since LOCS was last cleared.
1
ICG has lost clock since LOCS was last cleared, LOCRE determines action taken.
1
External Reference Clock Status — The ERCS bit is an indication of whether or not the external reference
ERCS
clock (ICGERCLK) meets the minimum frequency requirement.
0
1
External reference clock is not stable, frequency requirement is not met.
External reference clock is stable, frequency requirement is met.
0
ICG Interrupt Flag — The ICGIF read/write flag is set when an ICG interrupt request is pending. It is cleared by
a reset or by reading the ICG status register when ICGIF is set and then writing a logic 1 to ICGIF. If another ICG
interrupt occurs before the clearing sequence is complete, the sequence is reset so ICGIF would remain set after
the clear sequence was completed for the earlier interrupt. Writing a logic 0 to ICGIF has no effect.
ICGIF
0
1
No ICG interrupt request is pending.
An ICG interrupt request is pending.
MC9S08AW60 Data Sheet, Rev 2
138
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.3.4
ICG Status Register 2 (ICGS2)
7
6
5
4
3
2
1
0
R
0
0
0
0
0
0
0
DCOS
W
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 8-9. ICG Status Register 2 (ICGS2)
Table 8-4. ICGS2 Register Field Descriptions
Description
Field
0
DCO Clock Stable — The DCOS bit is set when the DCO clock (ICG2DCLK) is stable, meaning the count error
has not changed by more than nunlock for two consecutive samples and the DCO clock is not static. This bit is
used when exiting off state if CLKS = X1 to determine when to switch to the requested clock mode. It is also used
in self-clocked mode to determine when to start monitoring the DCO clock. This bit is cleared upon entering the
off state.
DCOS
0 DCO clock is unstable.
1 DCO clock is stable.
8.3.5
ICG Filter Registers (ICGFLTU, ICGFLTL)
7
6
5
4
3
2
1
0
R
W
0
0
0
0
FLT
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 8-10. ICG Upper Filter Register (ICGFLTU)
Table 8-5. ICGFLTU Register Field Descriptions
Description
Field
3:0
FLT
Filter Value — The FLT bits indicate the current filter value, which controls the DCO frequency. The FLT bits are
read only except when the CLKS bits are programmed to self-clocked mode (CLKS = 00). In self-clocked mode,
any write to ICGFLTU updates the current 12-bit filter value. Writes to the ICGFLTU register will not affect FLT if
a previous latch sequence is not complete.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
139
Chapter 8 Internal Clock Generator (S08ICGV4)
7
6
5
4
3
2
1
0
R
W
FLT
Reset
1
1
0
0
0
0
0
0
Figure 8-11. ICG Lower Filter Register (ICGFLTL)
Table 8-6. ICGFLTL Register Field Descriptions
Description
Field
7:0
FLT
Filter Value — The FLT bits indicate the current filter value, which controls the DCO frequency. The FLT bits are
read only except when the CLKS bits are programmed to self-clocked mode (CLKS = 00). In self-clocked mode,
any write to ICGFLTU updates the current 12-bit filter value. Writes to the ICGFLTU register will not affect FLT if
a previous latch sequence is not complete. The filter registers show the filter value (FLT).
8.3.6
ICG Trim Register (ICGTRM)
7
6
5
4
3
2
1
0
R
W
TRIM
1
0
0
0
0
0
0
0
POR
Reset:
U
U
U
U
U
U
U
U
U = Unaffected by MCU reset
Figure 8-12. ICG Trim Register (ICGTRM)
Table 8-7. ICGTRM Register Field Descriptions
Description
Field
7
ICG Trim Setting — The TRIM bits control the internal reference generator frequency. They allow a 25%
adjustment of the nominal (POR) period. The bit’s effect on period is binary weighted (i.e., bit 1 will adjust twice
as much as changing bit 0). Increasing the binary value in TRIM will increase the period and decreasing the value
will decrease the period.
TRIM
8.4
Functional Description
This section provides a functional description of each of the five operating modes of the ICG. Also
discussed are the loss of clock and loss of lock errors and requirements for entry into each mode. The ICG
is very flexible, and in some configurations, it is possible to exceed certain clock specifications. When
using the FLL, configure the ICG so that the frequency of ICGDCLK does not exceed its maximum value
to ensure proper MCU operation.
MC9S08AW60 Data Sheet, Rev 2
140
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.4.1
Off Mode (Off)
Normally when the CPU enters stop mode, the ICG will cease all clock activity and is in the off state.
However there are two cases to consider when clock activity continues while the CPU is in stop mode,
8.4.1.1
BDM Active
When the BDM is enabled, the ICG continues activity as originally programmed. This allows access to
memory and control registers via the BDC controller.
8.4.1.2
OSCSTEN Bit Set
When the oscillator is enabled in stop mode (OSCSTEN = 1), the individual clock generators are enabled
but the clock feed to the rest of the MCU is turned off. This option is provided to avoid long oscillator
startup times if necessary, or to run the RTI from the oscillator during stop3.
8.4.1.3
Stop/Off Mode Recovery
Upon the CPU exiting stop mode due to an interrupt, the previously set control bits are valid and the system
clock feed resumes. If FEE is selected, the ICG will source the internal reference until the external clock
is stable. If FBE is selected, the ICG will wait for the external clock to stabilize before enabling ICGOUT.
Upon the CPU exiting stop mode due to a reset, the previously set ICG control bits are ignored and the
default reset values applied. Therefore the ICG will exit stop in SCM mode configured for an
approximately 8 MHz DCO output (4 MHz bus clock) with trim value maintained. If using a crystal, 4096
clocks are detected prior to engaging ICGERCLK. This is incorporated in crystal start-up time.
8.4.2
Self-Clocked Mode (SCM)
Self-clocked mode (SCM) is the default mode of operation and is entered when any of the following
conditions occur:
•
•
After any reset.
Exiting from off mode when CLKS does not equal 10. If CLKS = X1, the ICG enters this state
temporarily until the DCO is stable (DCOS = 1).
•
•
CLKS bits are written from X1 to 00.
CLKS = 1X and ICGERCLK is not detected (both ERCS = 0 and LOCS = 1).
In this state, the FLL loop is open. The DCO is on, and the output clock signal ICGOUT frequency is given
by f / R. The ICGDCLK frequency can be varied from 8 MHz to 40 MHz by writing a new value
ICGDCLK
into the filter registers (ICGFLTH and ICGFLTL). This is the only mode in which the filter registers can
be written.
If this mode is entered due to a reset, f
will default to f
which is nominally 8 MHz. If this
Self_reset
ICGDCLK
mode is entered from FLL engaged internal, f
will maintain the previous frequency.If this mode
ICGDCLK
is entered from FLL engaged external (either by programming CLKS or due to a loss of external reference
clock), f will maintain the previous frequency, but ICGOUT will double if the FLL was unlocked.
ICGDCLK
If this mode is entered from off mode, f
will be equal to the frequency of ICGDCLK before
ICGDCLK
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
141
Chapter 8 Internal Clock Generator (S08ICGV4)
entering off mode. If CLKS bits are set to 01 or 11 coming out of the Off state, the ICG enters this mode
until ICGDCLK is stable as determined by the DCOS bit. After ICGDCLK is considered stable, the ICG
automatically closes the loop by switching to FLL engaged (internal or external) as selected by the CLKS
bits.
CLKST
CLKS
RFD
REFERENCE
DIVIDER (/7)
ICGIRCLK
CLOCK
SELECT
CIRCUIT
REDUCED
FREQUENCY
DIVIDER (R)
ICGOUT
RANGE
MFD
ICGDCLK
FLT
1x
2x
DIGITAL
LOOP
FILTER
DIGITALLY
CONTROLLED
OSCILLATOR
SUBTRACTOR
FLL ANALOG
CLKST
FREQUENCY-
LOCKED
LOOP (FLL)
OVERFLOW
ICG2DCLK
PULSE
COUNTER
COUNTER ENABLE
RANGE
IRQ
LOCK AND
LOSS OF CLOCK
DETECTOR
RESET AND
INTERRUPT
CONTROL
RESET
DCOS LOCK LOLS LOCS ERCS LOCD
ICGIF LOLRE LOCRE
Figure 8-13. Detailed Frequency-Locked Loop Block Diagram
8.4.3
FLL Engaged, Internal Clock (FEI) Mode
FLL engaged internal (FEI) is entered when any of the following conditions occur:
•
•
CLKS bits are written to 01
The DCO clock stabilizes (DCOS = 1) while in SCM upon exiting the off state with CLKS = 01
In FLL engaged internal mode, the reference clock is derived from the internal reference clock
ICGIRCLK, and the FLL loop will attempt to lock the ICGDCLK frequency to the desired value, as
selected by the MFD bits.
MC9S08AW60 Data Sheet, Rev 2
142
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.4.4
FLL Engaged Internal Unlocked
FEI unlocked is a temporary state that is entered when FEI is entered and the count error (Δn) output from
the subtractor is greater than the maximum n
lock detector to detect the unlock condition.
or less than the minimum n
, as required by the
unlock
unlock
The ICG will remain in this state while the count error (Δn) is greater than the maximum n
or less than
lock
the minimum n , as required by the lock detector to detect the lock condition.
lock
In this state the output clock signal ICGOUT frequency is given by f
/ R.
ICGDCLK
8.4.5
FLL Engaged Internal Locked
FLL engaged internal locked is entered from FEI unlocked when the count error (Δn), which comes from
the subtractor, is less than n (max) and greater than n (min) for a given number of samples, as
lock
lock
required by the lock detector to detect the lock condition. The output clock signal ICGOUT frequency is
given by f / R. In FEI locked, the filter value is updated only once every four comparison cycles.
ICGDCLK
The update made is an average of the error measurements taken in the four previous comparisons.
8.4.6
FLL Bypassed, External Clock (FBE) Mode
FLL bypassed external (FBE) is entered when any of the following conditions occur:
•
•
•
From SCM when CLKS = 10 and ERCS is high
When CLKS = 10, ERCS = 1 upon entering off mode, and off is then exited
From FLL engaged external mode if a loss of DCO clock occurs and the external reference remains
valid (both LOCS = 1 and ERCS = 1)
In this state, the DCO and IRG are off and the reference clock is derived from the external reference clock,
ICGERCLK. The output clock signal ICGOUT frequency is given by f / R. If an external clock
ICGERCLK
source is used (REFS = 0), then the input frequency on the EXTAL pin can be anywhere in the range
0 MHz to 40 MHz. If a crystal or resonator is used (REFS = 1), then frequency range is either low for
RANGE = 0 or high for RANGE = 1.
8.4.7
FLL Engaged, External Clock (FEE) Mode
The FLL engaged external (FEE) mode is entered when any of the following conditions occur:
•
•
CLKS = 11 and ERCS and DCOS are both high.
The DCO stabilizes (DCOS = 1) while in SCM upon exiting the off state with CLKS = 11.
In FEE mode, the reference clock is derived from the external reference clock ICGERCLK, and the FLL
loop will attempt to lock the ICGDCLK frequency to the desired value, as selected by the MFD bits. To
run in FEE mode, there must be a working 32 kHz–100 kHz or 2 MHz–10 MHz external clock source. The
maximum external clock frequency is limited to 10 MHz in FEE mode to prevent over-clocking the DCO.
The minimum multiplier for the FLL, from Table 8-12 is 4. Because 4 X 10 MHz is 40MHz, which is the
operational limit of the DCO, the reference clock cannot be any faster than 10 MHz.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
143
Chapter 8 Internal Clock Generator (S08ICGV4)
8.4.7.1
FLL Engaged External Unlocked
FEE unlocked is entered when FEE is entered and the count error (Δn) output from the subtractor is greater
than the maximum n
unlock condition.
or less than the minimum n
, as required by the lock detector to detect the
unlock
unlock
The ICG will remain in this state while the count error (Δn) is greater than the maximum n
or less than
lock
the minimum n , as required by the lock detector to detect the lock condition.
lock
In this state, the pulse counter, subtractor, digital loop filter, and DCO form a closed loop and attempt to
lock it according to their operational descriptions later in this section. Upon entering this state and until
the FLL becomes locked, the output clock signal ICGOUT frequency is given by f
/ (2×R) This
ICGDCLK
extra divide by two prevents frequency overshoots during the initial locking process from exceeding
chip-level maximum frequency specifications. After the FLL has locked, if an unexpected loss of lock
causes it to re-enter the unlocked state while the ICG remains in FEE mode, the output clock signal
ICGOUT frequency is given by f
/ R.
ICGDCLK
8.4.7.2
FLL Engaged External Locked
FEE locked is entered from FEE unlocked when the count error (Δn) is less than n
(max) and greater
lock
than n
(min) for a given number of samples, as required by the lock detector to detect the lock
lock
condition. The output clock signal ICGOUT frequency is given by f
/R. In FLL engaged external
ICGDCLK
locked, the filter value is updated only once every four comparison cycles. The update made is an average
of the error measurements taken in the four previous comparisons.
8.4.8
FLL Lock and Loss-of-Lock Detection
To determine the FLL locked and loss-of-lock conditions, the pulse counter counts the pulses of the DCO
for one comparison cycle (see Table 8-9 for explanation of a comparison cycle) and passes this number to
the subtractor. The subtractor compares this value to the value in MFD and produces a count error, Δn. To
achieve locked status, Δn must be between n
(min) and n
(max). After the FLL has locked, Δn must
lock
lock
stay between n
(min) and n
(max) to remain locked. If Δn goes outside this range unexpectedly,
unlock
unlock
the LOLS status bit is set and remains set until cleared by software or until the MCU is reset. LOLS is
cleared by reading ICGS1 then writing 1 to ICGIF (LOLRE = 0), or by a loss-of-lock induced reset
(LOLRE = 1), or by any MCU reset.
If the ICG enters the off state due to stop mode when ENBDM = OSCSTEN = 0, the FLL loses locked
status (LOCK is cleared), but LOLS remains unchanged because this is not an unexpected loss-of-lock
condition. Though it would be unusual, if ENBDM is cleared to 0 while the MCU is in stop, the ICG enters
the off state. Because this is an unexpected stopping of clocks, LOLS will be set when the MCU wakes up
from stop.
Expected loss of lock occurs when the MFD or CLKS bits are changed or in FEI mode only, when the
TRIM bits are changed. In these cases, the LOCK bit will be cleared until the FLL regains lock, but the
LOLS will not be set.
MC9S08AW60 Data Sheet, Rev 2
144
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.4.9
FLL Loss-of-Clock Detection
The reference clock and the DCO clock are monitored under different conditions (see Table 8-8). Provided
the reference frequency is being monitored, ERCS = 1 indicates that the reference clock meets minimum
frequency requirements. When the reference and/or DCO clock(s) are being monitored, if either one falls
below a certain frequency, f
and f
, respectively, the LOCS status bit will be set to indicate the error.
LOR
LOD
LOCS will remain set until it is acknowledged or until the MCU is reset. LOCS is cleared by reading
ICGS1 then writing 1 to ICGIF (LOCRE = 0), or by a loss-of-clock induced reset (LOCRE = 1), or by any
MCU reset.
If the ICG is in FEE, a loss of reference clock causes the ICG to enter SCM, and a loss of DCO clock causes
the ICG to enter FBE mode. If the ICG is in FBE mode, a loss of reference clock will cause the ICG to
enter SCM. In each case, the CLKST and CLKS bits will be automatically changed to reflect the new state.
If the ICG is in FEE mode when a loss of clock occurs and the ERCS is still set to 1, then the CLKST bits
are set to 10 and the ICG reverts to FBE mode.
A loss of clock will also cause a loss of lock when in FEE or FEI modes. Because the method of clearing
the LOCS and LOLS bits is the same, this would only be an issue in the unlikely case that LOLRE = 1 and
LOCRE = 0. In this case, the interrupt would be overridden by the reset for the loss of lock.
Table 8-8. Clock Monitoring (When LOCD = 0)
External Reference
DCO Clock
Mode
CLKS
REFST
ERCS
Clock
Monitored?
Monitored?
Off
0X or 11
10
X
0
1
X
0
1
X
X
X
0
1
X
Forced Low
Forced Low
Real-Time1
Forced Low
Forced High
Real-Time
Real-Time
Forced Low
Real-Time
Forced High
Real-Time
Real-Time
No
No
Yes(1)
No
No
10
No
SCM
(CLKST = 00)
0X
No
Yes2
Yes(2)
Yes(2)
Yes(2)
Yes
10
No
10
Yes
Yes
No
11
FEI
(CLKST = 01)
0X
11
Yes
No
Yes
FBE
(CLKST = 10)
10
No
10
Yes
Yes
No
FEE
11
Yes
(CLKST = 11)
1
2
If ENABLE is high (waiting for external crystal start-up after exiting stop).
DCO clock will not be monitored until DCOS = 1 upon entering SCM from off or FLL bypassed external mode.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
145
Chapter 8 Internal Clock Generator (S08ICGV4)
8.4.10 Clock Mode Requirements
A clock mode is requested by writing to CLKS1:CLKS0 and the actual clock mode is indicated by
CLKST1:CLKST0. Provided minimum conditions are met, the status shown in CLKST1:CLKST0 should
be the same as the requested mode in CLKS1:CLKS0. Table 8-9 shows the relationship between CLKS,
CLKST, and ICGOUT. It also shows the conditions for CLKS = CLKST or the reason CLKS ≠ CLKST.
NOTE
If a crystal will be used before the next reset, then be sure to set REFS = 1
and CLKS = 1x on the first write to the ICGC1 register. Failure to do so will
result in “locking” REFS = 0 which will prevent the oscillator amplifier
from being enabled until the next reset occurs.
Table 8-9. ICG State Table
Actual
Mode
(CLKST)
Desired
Mode
(CLKS)
Reference
Frequency
(fREFERENCE)
Reason
CLKS1 ≠
CLKST
Comparison
Cycle Time
Conditions1 for
CLKS = CLKST
Range
ICGOUT
Off
(XX)
X
X
0
0
—
—
0
0
—
—
—
Off
(XX)
FBE
(10)
ERCS = 0
Not switching
from FBE to
SCM
SCM
(00)
ICGIRCLK/72
8/fICGIRCLK
X
ICGDCLK/R
—
f
FEI
(01)
8/fICGIRCLK
8/fICGIRCLK
8/fICGIRCLK
8/fICGIRCLK
8/fICGIRCLK
0
X
X
0
ICGDCLK/R
ICGDCLK/R
ICGDCLK/R
ICGDCLK/R
ICGDCLK/R
ICGERCLK/R
ICGERCLK/R
ICGDCLK/R3
ICGDCLK/R(2)
—
DCOS = 0
ERCS = 0
f
f
f
ICGIRCLK/7(1)
ICGIRCLK/7(1)
ICGIRCLK/7(1)
SCM
(00)
FBE
(10)
—
—
FEE
(11)
DCOS = 0 or
ERCS = 0
FEI
(01)
fICGIRCLK/7
DCOS = 1
—
—
ERCS = 0
—
FEI
(01)
FEE
(11)
fICGIRCLK/7
X
X
X
0
FBE
(10)
0
—
ERCS = 1
—
FBE
(10)
FEE
(11)
LOCS = 1 &
ERCS = 1
0
—
ERCS = 1 and
DCOS = 1
fICGERCLK
fICGERCLK
2/fICGERCLK
128/fICGERCLK
—
—
FEE
(11)
FEE
(11)
ERCS = 1 and
DCOS = 1
1
1
2
3
CLKST will not update immediately after a write to CLKS. Several bus cycles are required before CLKST updates to the new
value.
The reference frequency has no effect on ICGOUT in SCM, but the reference frequency is still used in making the comparisons
that determine the DCOS bit
After initial LOCK; will be ICGDCLK/2R during initial locking process and while FLL is re-locking after the MFD bits are changed.
MC9S08AW60 Data Sheet, Rev 2
146
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.4.11 Fixed Frequency Clock
The ICG provides a fixed frequency clock output, XCLK, for use by on-chip peripherals. This output is
equal to the internal bus clock, BUSCLK, in all modes except FEE. In FEE mode, XCLK is equal to
ICGERCLK ÷ 2 when the following conditions are met:
•
(P × N) ÷ R ≥ 4 where P is determined by RANGE (see Table 8-11), N and R are determined by
MFD and RFD respectively (see Table 8-12).
•
LOCK = 1.
If the above conditions are not true, then XCLK is equal to BUSCLK.
When the ICG is in either FEI or SCM mode, XCLK is turned off. Any peripherals which can use XCLK
as a clock source must not do so when the ICG is in FEI or SCM mode.
8.4.12 High Gain Oscillator
The oscillator has the option of running in a high gain oscillator (HGO) mode, which improves the
oscillator's resistance to EMC noise when running in FBE or FEE modes. This option is selected by writing
a 1 to the HGO bit in the ICGC1 register. HGO is used with both the high and low range oscillators but is
only valid when REFS = 1 in the ICGC1 register. When HGO = 0, the standard low-power oscillator is
selected. This bit is writable only once after any reset.
8.5
Initialization/Application Information
Introduction
8.5.1
The section is intended to give some basic direction on which configuration a user would want to select
when initializing the ICG. For some applications, the serial communication link may dictate the accuracy
of the clock reference. For other applications, lowest power consumption may be the chief clock
consideration. Still others may have lowest cost as the primary goal. The ICG allows great flexibility in
choosing which is best for any application.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
147
Chapter 8 Internal Clock Generator (S08ICGV4)
Table 8-10. ICG Configuration Consideration
Clock Reference Source = Internal
Clock Reference Source = External
FEI
FEE
4 MHz < fBus < 20 MHz.
4 MHz < fBus < 20 MHz
Medium power (will be less than FEE if oscillator
range = high)
Medium power (will be less than FEI if oscillator
range = low)
FLL
Good clock accuracy (After IRG is trimmed)
Lowest system cost (no external components
required)
IRG is on. DCO is on. 1
Engaged
High clock accuracy
Medium/High system cost (crystal, resonator or
external clock source required)
IRG is off. DCO is on.
SCM
FBE
This mode is mainly provided for quick and reliable
system startup.
3 MHz < fBus < 5 MHz (default).
3 MHz < fBus < 20 MHz (via filter bits).
Medium power
Poor accuracy.
IRG is off. DCO is on and open loop.
fBus range ≤ 8 MHz when crystal or resonator is
used.
Lowest power
Highest clock accuracy
Medium/High system cost (Crystal, resonator or
external clock source required)
IRG is off. DCO is off.
FLL
Bypassed
1
The IRG typically consumes 100 μA. The FLL and DCO typically consumes 0.5 to 2.5 mA, depending upon output frequency.
For minimum power consumption and minimum jitter, choose N and R to be as small as possible.
The following sections contain initialization examples for various configurations.
NOTE
Hexadecimal values designated by a preceding $, binary values designated
by a preceding %, and decimal values have no preceding character.
Important configuration information is repeated here for reference.
Table 8-11. ICGOUT Frequency Calculation Options
1
Clock Scheme
fICGOUT
P
Note
SCM — self-clocked mode (FLL bypassed
internal)
fICGDCLK / R
NA
Typical fICGOUT = 8 MHz
immediately after reset
FBE — FLL bypassed external
FEI — FLL engaged internal
FEE — FLL engaged external
fext / R
NA
64
(fIRG / 7)* 64 * N / R
fext * P * N / R
Typical fIRG = 243 kHz
Range = 0 ; P = 64
Range = 1; P = 1
1
Ensure that f
, which is equal to f
* R, does not exceed f
.
ICGDCLK
ICGOUT
ICGDCLKmax
Table 8-12. MFD and RFD Decode Table
MFD Value
Multiplication Factor (N)
RFD
Division Factor (R)
000
001
010
011
100
4
6
000
001
010
011
100
÷1
÷2
÷4
÷8
÷16
8
10
12
MC9S08AW60 Data Sheet, Rev 2
148
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
Table 8-12. MFD and RFD Decode Table
101
110
111
14
16
18
101
110
111
÷32
÷64
÷128
8.5.2
Example #1: External Crystal = 32 kHz, Bus Frequency = 4.19 MHz
In this example, the FLL will be used (in FEE mode) to multiply the external 32 kHz oscillator up to
8.38 MHz to achieve 4.19 MHz bus frequency.
After the MCU is released from reset, the ICG is in self-clocked mode (SCM) and supplies approximately
8 MHz on ICGOUT, which corresponds to a 4 MHz bus frequency (f ).
Bus
The clock scheme will be FLL engaged, external (FEE). So
f
= f * P * N / R ; P = 64, f = 32 kHz
ext
Eqn. 8-1
Eqn. 8-2
ICGOUT
ext
Solving for N / R gives:
N / R = 8.38 MHz /(32 kHz * 64) = 4 ; we can choose N = 4 and R =1
The values needed in each register to set up the desired operation are:
ICGC1 = $38 (%00111000)
Bit 7
Bit 6
Bit 5
HGO
RANGE
REFS
0
0
1
11
Configures oscillator for low power
Configures oscillator for low-frequency range; FLL prescale factor is 64
Oscillator using crystal or resonator is requested
FLL engaged, external reference clock mode
Oscillator disabled
Loss-of-clock detection enabled
Unimplemented or reserved, always reads zero
Bits 4:3 CLKS
Bit 2
Bit 1
Bit 0
OSCSTEN 0
LOCD
0
0
ICGC2 = $00 (%00000000)
Bit 7 LOLRE
0
Generates an interrupt request on loss of lock
Bits 6:4 MFD
000 Sets the MFD multiplication factor to 4
Generates an interrupt request on loss of clock
000 Sets the RFD division factor to ÷1
Bit 3
LOCRE
0
Bits 2:0 RFD
ICGS1 = $xx
This is read only except for clearing interrupt flag
ICGS2 = $xx
This is read only; should read DCOS = 1 before performing any time critical tasks
ICGFLTLU/L = $xx
Only needed in self-clocked mode; FLT will be adjusted by loop to give 8.38 MHz DCO clock
Bits 15:12 unused
0000
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
149
Chapter 8 Internal Clock Generator (S08ICGV4)
Bits 11:0 FLT
ICGTRM = $xx
Bits 7:0 TRIM
No need for user initialization
Only need to write when trimming internal oscillator; not used when external
crystal is clock source
Figure 8-14 shows flow charts for three conditions requiring ICG initialization.
QUICK RECOVERY FROM STOP
MINIMUM CURRENT DRAW IN STOP
RESET
RECOVERY FROM STOP
OSCSTEN = 0
RECOVERY FROM STOP
OSCSTEN = 1
INITIALIZE ICG
ICGC1 = $38
ICGC2 = $00
CHECK
NO
CHECK
NO
FLL LOCK STATUS.
FLL LOCK STATUS.
LOCK = 1?
LOCK = 1?
YES
YES
CHECK
FLL LOCK STATUS.
LOCK = 1?
NO
CONTINUE
CONTINUE
YES
CONTINUE
NOTE: THIS WILL REQUIRE THE OSCILLATOR TO START AND
STABILIZE. ACTUAL TIME IS DEPENDENT ON CRYSTAL /RESONATOR
AND EXTERNAL CIRCUITRY.
Figure 8-14. ICG Initialization for FEE in Example #1
MC9S08AW60 Data Sheet, Rev 2
150
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.5.3
Example #2: External Crystal = 4 MHz, Bus Frequency = 20 MHz
In this example, the FLL will be used (in FEE mode) to multiply the external 4 MHz oscillator up to
40-MHz to achieve 20 MHz bus frequency.
After the MCU is released from reset, the ICG is in self-clocked mode (SCM) and supplies approximately
8 MHz on ICGOUT which corresponds to a 4 MHz bus frequency (f ).
Bus
During reset initialization software, the clock scheme will be set to FLL engaged, external (FEE). So
f
= f * P * N / R ; P = 1, f = 4.00 MHz
Eqn. 8-3
ICGOUT
ext
ext
Solving for N / R gives:
N / R = 40 MHz /(4 MHz * 1) = 10 ; We can choose N = 10 and R = 1
The values needed in each register to set up the desired operation are:
ICGC1 = $78 (%01111000)
Eqn. 8-4
Bit 7
Bit 6
Bit 5
HGO
RANGE
REFS
0
1
1
Configures oscillator for low power
Configures oscillator for high-frequency range; FLL prescale factor is 1
Requests an oscillator
Bits 4:3 CLKS
11
FLL engaged, external reference clock mode
Disables the oscillator
Loss-of-clock detection enabled
Bit 2
Bit 1
Bit 0
OSCSTEN 0
LOCD
0
0
Unimplemented or reserved, always reads zero
ICGC2 = $30 (%00110000)
Bit 7 LOLRE
0
Generates an interrupt request on loss of lock
Bit 6:4 MFD
011 Sets the MFD multiplication factor to 10
Generates an interrupt request on loss of clock
000 Sets the RFD division factor to ÷1
Bit 3
LOCRE
0
Bit 2:0 RFD
ICGS1 = $xx
This is read only except for clearing interrupt flag
ICGS2 = $xx
This is read only. Should read DCOS before performing any time critical tasks
ICGFLTLU/L = $xx
Not used in this example
ICGTRM
Not used in this example
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
151
Chapter 8 Internal Clock Generator (S08ICGV4)
RECOVERY
FROM STOP
RESET
INITIALIZE ICG
ICGC1 = $7A
ICGC2 = $30
SERVICE INTERRUPT
SOURCE (f
= 4 MHz)
Bus
CHECK
FLL LOCK STATUS
LOCK = 1?
NO
CHECK
FLL LOCK STATUS
LOCK = 1?
NO
YES
YES
CONTINUE
CONTINUE
Figure 8-15. ICG Initialization and Stop Recovery for Example #2
MC9S08AW60 Data Sheet, Rev 2
152
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.5.4
Example #3: No External Crystal Connection, 5.4 MHz Bus
Frequency
In this example, the FLL will be used (in FEI mode) to multiply the internal 243 kHz (approximate)
reference clock up to 10.8 MHz to achieve 5.4 MHz bus frequency. This system will also use the trim
function to fine tune the frequency based on an external reference signal.
After the MCU is released from reset, the ICG is in self-clocked mode (SCM) and supplies approximately
8 MHz on ICGOUT which corresponds to a 4 MHz bus frequency (f ).
Bus
The clock scheme will be FLL engaged, internal (FEI). So
f
= (f
/ 7) * P * N / R ; P = 64, f = 243 kHz
IRG
Eqn. 8-5
Eqn. 8-6
ICGOUT
IRG
Solving for N / R gives:
N / R = 10.8 MHz /(243/7 kHz * 64) = 4.86 ; We can choose N = 10 and R = 2.
A trim procedure will be required to hone the frequency to exactly 5.4 MHz. An example of the trim
procedure is shown in example #4.
The values needed in each register to set up the desired operation are:
ICGC1 = $28 (%00101000)
Bit 7
Bit 6
Bit 5
HGO
RANGE
REFS
0
0
1
01
Configures oscillator for low power
Configures oscillator for low-frequency range; FLL prescale factor is 64
Oscillator using crystal or resonator requested (bit is really a don’t care)
FLL engaged, internal reference clock mode
Disables the oscillator
Loss-of-clock enabled
Unimplemented or reserved, always reads zero
Bits 4:3 CLKS
Bit 2
Bit 1
Bit 0
OSCSTEN 0
LOCD
0
0
ICGC2 = $31 (%00110001)
Bit 7 LOLRE
Bit 6:4 MFD
0
Generates an interrupt request on loss of lock
011 Sets the MFD multiplication factor to 10
Generates an interrupt request on loss of clock
001 Sets the RFD division factor to ÷2
Bit 3
LOCRE
0
Bit 2:0 RFD
ICGS1 = $xx
This is read only except for clearing interrupt flag
ICGS2 = $xx
This is read only; good idea to read this before performing time critical operations
ICGFLTLU/L = $xx
Not used in this example
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
153
Chapter 8 Internal Clock Generator (S08ICGV4)
ICGTRM = $xx
Bit 7:0 TRIM
Only need to write when trimming internal oscillator; done in separate
operation (see example #4)
RECOVERY
FROM STOP
RESET
INITIALIZE ICG
ICGC1 = $28
ICGC2 = $31
CHECK
FLL LOCK STATUS.
LOCK = 1?
NO
YES
CHECK
FLL LOCK STATUS.
LOCK = 1?
NO
CONTINUE
YES
CONTINUE
NOTE: THIS WILL REQUIRE THE INTERAL REFERENCE CLOCK TO START AND
STABILIZE.
Figure 8-16. ICG Initialization and Stop Recovery for Example #3
MC9S08AW60 Data Sheet, Rev 2
154
Freescale Semiconductor
Chapter 8 Internal Clock Generator (S08ICGV4)
8.5.5
Example #4: Internal Clock Generator Trim
The internally generated clock source is guaranteed to have a period 25% of the nominal value. In some
cases, this may be sufficient accuracy. For other applications that require a tight frequency tolerance, a
trimming procedure is provided that will allow a very accurate source. This section outlines one example
of trimming the internal oscillator. Many other possible trimming procedures are valid and can be used.
Initial conditions:
1) Clock supplied from ATE has 500 μsec duty period
2) ICG configured for internal reference with 4 MHz bus
START TRIM PROCEDURE
ICGTRM = $80, n = 1
MEASURE
INCOMING CLOCK WIDTH
(COUNT = # OF BUS CLOCKS / 4)
COUNT < EXPECTED = 500
(RUNNING TOO SLOW)
COUNT = EXPECTED = 500
.
CASE STATEMENT
COUNT > EXPECTED = 500
(RUNNING TOO FAST)
ICGTRM =
ICGTRM - 128 / (2**n)
(DECREASING ICGTRM
INCREASES THE FREQUENCY)
ICGTRM =
STORE ICGTRM VALUE
IN NON-VOLATILE
MEMORY
ICGTRM + 128 / (2**n)
(INCREASING ICGTRM
DECREASES THE FREQUENCY)
CONTINUE
n = n + 1
YES
IS n > 8?
NO
Figure 8-17. Trim Procedure
In this particular case, the MCU has been attached to a PCB and the entire assembly is undergoing final
test with automated test equipment. A separate signal or message is provided to the MCU operating under
user provided software control. The MCU initiates a trim procedure as outlined in Figure 8-17 while the
tester supplies a precision reference signal.
If the intended bus frequency is near the maximum allowed for the device, it is recommended to trim using
a reduction divisor (R) twice the final value. After the trim procedure is complete, the reduction divisor
can be restored. This will prevent accidental overshoot of the maximum clock frequency.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
155
Chapter 8 Internal Clock Generator (S08ICGV4)
MC9S08AW60 Data Sheet, Rev 2
156
Freescale Semiconductor
Chapter 9
Keyboard Interrupt (S08KBIV1)
9.1
Introduction
The MC9S08AW60 Series has one KBI module with eight keyboard interrupt inputs that are shared with
port D and port G pins. See Chapter 2, “Pins and Connections,” for more information about the logic and
hardware aspects of these pins.
9.2
Keyboard Pin Sharing
The KBI input KBIP7 shares a common pin with PTD7 and AD15. When KBIP7 is enabled the pin is
forced to its input state regardless of the value of the associated port D data direction bit. The port D pullup
enable is still used to control the pullup resistor and the pin state can be sensed through a read of the port
D data register (this requires that bit 7 of the port D DDR is 0). In the case that the pin is enabled as an
ADC input, both the PTD7 and KBIP7 functions are disabled, including the pullup resistor.
The KBI input KBIP6 shares a common pin with PTD3 and AD11, and KBI input KBIP5 shares a common
pin with PTD2 and AD10. The sharing of each of these inputs with port and ADC functions operates in
the same way as described above for KBIP7.
The KBI inputs KBIP4 – KBIP0 are shared on common pins with PTG4 – PTG0. These pins all operate
in the same way as described above for KBIP7 except that none are shared with an ADC input.
KBIP3 – KBIP0 are always falling-edge/low-level sensitive. KBIP7 – KBIP4 can be configured for
rising-edge/high-level or for falling-edge/low-level sensitivity. When any of the inputs KBIP7 – KBIP0 are
enabled and configured to detect rising edges/high levels, and the pin pullup is enabled through the
corresponding port pullup enable bit for that pin, a pulldown resistor rather than a pullup resistor is enabled
on the pin.
Table 9-1. KBI and Parallel I/O Interaction
PTxPEn
(Pull Enable)
PTxDDn
KBIPEn
KBEDGn
Pullup
Pulldown
(Data Direction) (KBI Pin Enable) (KBI Edge Select)
0
1
x
1
1
0
0
0
1
x
x
x
0
0
0
1
1
1
x1
x
disabled
enabled
disabled
enabled
disabled
disabled
disabled
disabled
disabled
disabled
enabled
disabled
x
0
1
x
1
x = Don’t care
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
157
Chapter 9 Keyboard Interrupt (S08KBIV1)
9.3
Features
The keyboard interrupt (KBI) module features include:
•
•
•
•
•
Four falling edge/low level sensitive
Four falling edge/low level or rising edge/high level sensitive
Choice of edge-only or edge-and-level sensitivity
Common interrupt flag and interrupt enable control
Capable of waking up the MCU from stop3 or wait mode
MC9S08AW60 Data Sheet, Rev 2
158
Freescale Semiconductor
Chapter 9 Keyboard Interrupt (S08KBIV1)
HCS08 CORE
DEBUG
MODULE (DBG)
8
PTA7– PTA0
BKGD/MS
BDC
CPU
8
PTB7/AD1P7–
PTB0/AD1P0
HCS08 SYSTEM CONTROL
RESET
IRQ
PTC6
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
RxD2
TxD2
PTC5/RxD2
PTC4
PTC3/TxD2
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI2)
PTC2/MCLK
PTC1/SDA1
SDA1
SCL1
RTI
COP
LVD
IIC MODULE (IIC1)
PTC0/SCL1
IRQ
AD1P7–AD1P0
8
V
DDAD
8
10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC1)
AD1P15–AD1P8
V
SSAD
V
REFL
PTD7/AD1P15/KBI1P7
PTD6/AD1P14/TPM1CLK
PTD5/AD1P13
PTD4/AD1P12/TPM2CLK
PTD3/AD1P11/KBI1P6
PTD2/AD1P10/KBI1P5
PTD1/AD1P9
V
REFH
USER FLASH
(AW60 = 63,280 BYTES)
(AW48 = 49,152 BYTES)
(AW32 = 32,768 BYTES)
(AW16 = 16,384 BYTES)
PTD0/AD1P8
SPSCK1
PTE7/SPSCK1
PTE6/MOSI1
MOSI1
SERIAL PERIPHERAL
USER RAM
MISO1
SS1
INTERFACE MODULE (SPI1)
PTE5/MISO1
PTE4/SS1
AW60/48/32 = 2048 BYTES
AW16 = 1024 BYTES
TPM1CLK
PTE3/TPM1CH1
PTE2/TPM1CH0
6-CHANNEL TIMER/PWM
MODULE (TPM1)
TPM1CH5–
TPM1CH0
INTERNAL CLOCK
GENERATOR (ICG)
6
RxD1
TxD1
PTE1/RxD1
PTE0/TxD1
PTF7
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI1)
LOW-POWER OSCILLATOR
PTF6
PTF5/TPM2CH1
PTF4/TPM2CH0
TPM2CLK
V
DD
VOLTAGE
REGULATOR
2-CHANNEL TIMER/PWM
MODULE (TPM2)
TPM2CH1–TPM2CH0
V
SS
2
PTF3/TPM1CH5
KBI1P7–KBI1P5
3
PTF2/TPM1CH4
PTF1/TPM1CH3
PTF0/TPM1CH2
8-BIT KEYBOARD
INTERRUPT MODULE (KBI1)
KBI1P4–KBI1P0
5
EXTAL
XTAL
PTG6/EXTAL
PTG5/XTAL
NOTES:
PTG4/KBI1P4
PTG3/KBI1P3
PTG2/KBI1P2
PTG1/KBI1P1
PTG0/KBI1P0
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software configurable pullup/pulldown device if IRQ is enabled
(IRQPE = 1). Pulldown is enabled if rising edge detect is selected (IRQEDG = 1)
3. IRQ does not have a clamp diode to VDD. IRQ should not be driven above VDD
4. Pin contains integrated pullup device.
.
5. Pins PTD7, PTD3, PTD2, and PTG4 contain both pullup and pulldown devices.
Pulldown enabled when KBI is enabled (KBIPEn = 1) and rising edge is selected
(KBEDGn = 1).
Figure 9-1. Block Diagram Highlighting KBI Module
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
159
Chapter 9 Keyboard Interrupt (S08KBIV1)
9.3.1
KBI Block Diagram
Figure 9-2 shows the block diagram for a KBI module.
KBI1P0
KBIPE0
BUSCLK
KBACK
RESET
KBI1P3
V
KBIPE3
KBIPE4
DD
KBF
CLR
D
Q
1
0
SYNCHRONIZER
STOP BYPASS
CK
KBI1P4
S
KEYBOARD
INTERRUPT FF
STOP
KEYBOARD
INTERRUPT
REQUEST
KBEDG4
KBIMOD
1
0
KBIE
KBI1Pn
S
KBIPEn
KBEDGn
Figure 9-2. KBI Block Diagram
9.4
Register Definition
This section provides information about all registers and control bits associated with the KBI module.
Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address
assignments for all KBI registers. This section refers to registers and control bits only by their names. A
Freescale-provided equate or header file is used to translate these names into the appropriate absolute
addresses.
MC9S08AW60 Data Sheet, Rev 2
160
Freescale Semiconductor
Chapter 9 Keyboard Interrupt (S08KBIV1)
9.4.1
KBI Status and Control Register (KBI1SC)
7
6
5
4
3
2
1
0
R
KBF
0
KBEDG7
KBEDG6
KBEDG5
KBEDG4
KBIE
KBIMOD
W
KBACK
0
Reset
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 9-3. KBI Status and Control Register (KBI1SC)
Table 9-2. KBI1SC Register Field Descriptions
Description
Field
7:4
Keyboard Edge Select for KBI Port Bits — Each of these read/write bits selects the polarity of the edges and/or
KBEDG[7:4] levels that are recognized as trigger events on the corresponding KBI port pin when it is configured as a keyboard
interrupt input (KBIPEn = 1). Also see the KBIMOD control bit, which determines whether the pin is sensitive to
edges-only or edges and levels.
0 Falling edges/low levels
1 Rising edges/high levels
3
Keyboard Interrupt Flag — This read-only status flag is set whenever the selected edge event has been
KBF
detected on any of the enabled KBI port pins. This flag is cleared by writing a 1 to the KBACK control bit. The
flag will remain set if KBIMOD = 1 to select edge-and-level operation and any enabled KBI port pin remains at
the asserted level.
KBF can be used as a software pollable flag (KBIE = 0) or it can generate a hardware interrupt request to the
CPU (KBIE = 1).
0 No KBI interrupt pending
1 KBI interrupt pending
2
Keyboard Interrupt Acknowledge — This write-only bit (reads always return 0) is used to clear the KBF status
flag by writing a 1 to KBACK. When KBIMOD = 1 to select edge-and-level operation and any enabled KBI port
pin remains at the asserted level, KBF is being continuously set so writing 1 to KBACK does not clear the KBF
flag.
KBACK
1
Keyboard Interrupt Enable — This read/write control bit determines whether hardware interrupts are generated
when the KBF status flag equals 1. When KBIE = 0, no hardware interrupts are generated, but KBF can still be
used for software polling.
KBIE
0 KBF does not generate hardware interrupts (use polling)
1 KBI hardware interrupt requested when KBF = 1
KBIMOD
Keyboard Detection Mode — This read/write control bit selects either edge-only detection or edge-and-level
detection. KBI port bits 3 through 0 can detect falling edges-only or falling edges and low levels. KBI port bits 7
through 4 can be configured to detect either:
• Rising edges-only or rising edges and high levels (KBEDGn = 1)
• Falling edges-only or falling edges and low levels (KBEDGn = 0)
0 Edge-only detection
1 Edge-and-level detection
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
161
Chapter 9 Keyboard Interrupt (S08KBIV1)
9.4.2
KBI Pin Enable Register (KBI1PE)
7
6
5
4
3
2
1
0
R
KBIPE7
KBIPE6
KBIPE5
KBIPE4
KBIPE3
KBIPE2
KBIPE1
KBIPE0
W
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 9-4. KBI Pin Enable Register (KBI1PE)
Table 9-3. KBI1PE Register Field Descriptions
Description
Field
7:0
Keyboard Pin Enable for KBI Port Bits — Each of these read/write bits selects whether the associated KBI
KBIPE[7:0] port pin is enabled as a keyboard interrupt input or functions as a general-purpose I/O pin.
0 Bit n of KBI port is a general-purpose I/O pin not associated with the KBI
1 Bit n of KBI port enabled as a keyboard interrupt input
9.5
Functional Description
Pin Enables
9.5.1
The KBIPEn control bits in the KBI1PE register allow a user to enable (KBIPEn = 1) any combination of
KBI-related port pins to be connected to the KBI module. Pins corresponding to 0s in KBI1PE are
general-purpose I/O pins that are not associated with the KBI module.
9.5.2
Edge and Level Sensitivity
Synchronous logic is used to detect edges. Prior to detecting an edge, enabled keyboard inputs in a KBI
module must be at the deasserted logic level.
A falling edge is detected when an enabled keyboard input signal is seen as a logic 1 (the deasserted level)
during one bus cycle and then a logic 0 (the asserted level) during the next cycle.
A rising edge is detected when the input signal is seen as a logic 0 during one bus cycle and then a logic 1
during the next cycle.
The KBIMOD control bit can be set to reconfigure the detection logic so that it detects edges and levels.
In KBIMOD = 1 mode, the KBF status flag becomes set when an edge is detected (when one or more
enabled pins change from the deasserted to the asserted level while all other enabled pins remain at their
deasserted levels), but the flag is continuously set (and cannot be cleared) as long as any enabled keyboard
input pin remains at the asserted level. When the MCU enters stop3 mode, the synchronous edge-detection
logic is bypassed (because clocks are stopped). In stop3 mode, KBI inputs act as asynchronous
level-sensitive inputs so they can wake the MCU from stop3 mode.
MC9S08AW60 Data Sheet, Rev 2
162
Freescale Semiconductor
Chapter 9 Keyboard Interrupt (S08KBIV1)
9.5.3
KBI Interrupt Controls
The KBF status flag becomes set (1) when an edge event has been detected on any KBI input pin. If
KBIE = 1 in the KBI1SC register, a hardware interrupt will be requested whenever KBF = 1. The KBF flag
is cleared by writing a 1 to the keyboard acknowledge (KBACK) bit.
When KBIMOD = 0 (selecting edge-only operation), KBF is always cleared by writing 1 to KBACK.
When KBIMOD = 1 (selecting edge-and-level operation), KBF cannot be cleared as long as any keyboard
input is at its asserted level.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
163
Chapter 9 Keyboard Interrupt (S08KBIV1)
MC9S08AW60 Data Sheet, Rev 2
164
Freescale Semiconductor
Chapter 10
Timer/PWM (S08TPMV2)
10.1 Introduction
The MC9S08AW60 Series includes two independent timer/PWM (TPM) modules which support
traditional input capture, output compare, or buffered edge-aligned pulse-width modulation (PWM) on
each channel. A control bit in each TPM configures all channels in that timer to operate as center-aligned
PWM functions. In each of these two TPMs, timing functions are based on a separate 16-bit counter with
prescaler and modulo features to control frequency and range (period between overflows) of the time
reference. This timing system is ideally suited for a wide range of control applications, and the
center-aligned PWM capability on the 3-channel TPM extends the field of applications to motor control in
small appliances.
The use of the fixed system clock, XCLK, as the clock source for either of the TPM modules allows the
TPM prescaler to run using the oscillator rate divided by two (ICGERCLK/2). This option is only available
if the ICG is configured in FEE mode and the proper conditions are met (see Section 8.4.11, “Fixed
Frequency Clock”). In all other ICG modes this selection is redundant because XCLK is the same as
BUSCLK.
10.2 Features
The timer system in the MC9S08AW60 Series includes a 6-channel TPM1 and a separate 2-channel
TPM2. Timer system features include:
•
A total of eight channels:
— Each channel may be input capture, output compare, or buffered edge-aligned PWM
— Rising-edge, falling-edge, or any-edge input capture trigger
— Set, clear, or toggle output compare action
— Selectable polarity on PWM outputs
•
•
Each TPM may be configured for buffered, center-aligned pulse-width modulation (CPWM) on all
channels
Clock source to prescaler for each TPM is independently selectable as bus clock, fixed system
clock, or an external pin:
— Prescale taps for divide by 1, 2, 4, 8, 16, 32, 64, or 128
— External clock inputs TPM1CLK for TPM1 and TPM2CLK for TPM2 (only available in
64-pin package)
•
•
•
•
16-bit free-running or up/down (CPWM) count operation
16-bit modulus register to control counter range
Timer system enable
One interrupt per channel plus a terminal count interrupt for each TPM module
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
165
Chapter 10 Timer/PWM (S08TPMV2)
HCS08 CORE
DEBUG
MODULE (DBG)
8
PTA7– PTA0
BKGD/MS
BDC
CPU
8
PTB7/AD1P7–
PTB0/AD1P0
HCS08 SYSTEM CONTROL
RESET
IRQ
PTC6
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
RxD2
TxD2
PTC5/RxD2
PTC4
PTC3/TxD2
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI2)
PTC2/MCLK
PTC1/SDA1
SDA1
SCL1
RTI
COP
LVD
IIC MODULE (IIC1)
PTC0/SCL1
IRQ
AD1P7–AD1P0
8
V
DDAD
8
10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC1)
AD1P15–AD1P8
V
SSAD
V
REFL
PTD7/AD1P15/KBI1P7
PTD6/AD1P14/TPM1CLK
PTD5/AD1P13
PTD4/AD1P12/TPM2CLK
PTD3/AD1P11/KBI1P6
PTD2/AD1P10/KBI1P5
PTD1/AD1P9
V
REFH
USER FLASH
(AW60 = 63,280 BYTES)
(AW48 = 49,152 BYTES)
(AW32 = 32,768 BYTES)
(AW16 = 16,384 BYTES)
PTD0/AD1P8
SPSCK1
PTE7/SPSCK1
PTE6/MOSI1
MOSI1
SERIAL PERIPHERAL
USER RAM
MISO1
SS1
INTERFACE MODULE (SPI1)
PTE5/MISO1
PTE4/SS1
AW60/48/32 = 2048 BYTES
AW16 = 1024 BYTES
TPM1CLK
PTE3/TPM1CH1
PTE2/TPM1CH0
6-CHANNEL TIMER/PWM
MODULE (TPM1)
TPM1CH5–
TPM1CH0
INTERNAL CLOCK
GENERATOR (ICG)
6
RxD1
TxD1
PTE1/RxD1
PTE0/TxD1
PTF7
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI1)
LOW-POWER OSCILLATOR
PTF6
PTF5/TPM2CH1
PTF4/TPM2CH0
TPM2CLK
V
DD
VOLTAGE
REGULATOR
2-CHANNEL TIMER/PWM
MODULE (TPM2)
TPM2CH1–TPM2CH0
V
SS
2
PTF3/TPM1CH5
KBI1P7–KBI1P5
3
PTF2/TPM1CH4
PTF1/TPM1CH3
PTF0/TPM1CH2
8-BIT KEYBOARD
INTERRUPT MODULE (KBI1)
KBI1P4–KBI1P0
5
EXTAL
XTAL
PTG6/EXTAL
PTG5/XTAL
NOTES:
PTG4/KBI1P4
PTG3/KBI1P3
PTG2/KBI1P2
PTG1/KBI1P1
PTG0/KBI1P0
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software configurable pullup/pulldown device if IRQ is enabled
(IRQPE = 1). Pulldown is enabled if rising edge detect is selected (IRQEDG = 1)
3. IRQ does not have a clamp diode to VDD. IRQ should not be driven above VDD
4. Pin contains integrated pullup device.
.
5. Pins PTD7, PTD3, PTD2, and PTG4 contain both pullup and pulldown devices.
Pulldown enabled when KBI is enabled (KBIPEn = 1) and rising edge is selected
(KBEDGn = 1).
Figure 10-1. Block Diagram Highlighting the TPM Module
MC9S08AW60 Data Sheet, Rev 2
166
Freescale Semiconductor
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
10.2.1 Features
The TPM has the following features:
•
Each TPM may be configured for buffered, center-aligned pulse-width modulation (CPWM) on all
channels
•
•
•
•
•
•
•
Clock sources independently selectable per TPM (multiple TPMs device)
Selectable clock sources (device dependent): bus clock, fixed system clock, external pin
Clock prescaler taps for divide by 1, 2, 4, 8, 16, 32, 64, or 128
16-bit free-running or up/down (CPWM) count operation
16-bit modulus register to control counter range
Timer system enable
One interrupt per channel plus a terminal count interrupt for each TPM module (multiple TPMs
device)
•
Channel features:
— Each channel may be input capture, output compare, or buffered edge-aligned PWM
— Rising-edge, falling-edge, or any-edge input capture trigger
— Set, clear, or toggle output compare action
— Selectable polarity on PWM outputs
10.2.2 Block Diagram
Figure 10-2 shows the structure of a TPM. Some MCUs include more than one TPM, with various
numbers of channels.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
167
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
BUSCLK
CLOCK SOURCE
SELECT
PRESCALE AND SELECT
DIVIDE BY
XCLK
OFF, BUS, XCLK, EXT
1, 2, 4, 8, 16, 32, 64, or 128
SYNC
TPMxCLK
PS2
PS1
PS0
CLKSB
CLKSA
CPWMS
MAIN 16-BIT COUNTER
TOF
TOIE
INTERRUPT
LOGIC
COUNTER RESET
16-BIT COMPARATOR
TPMxMODH:TPMxMODL
ELS0B ELS0A
CHANNEL 0
PORT
LOGIC
TPMxCH0
16-BIT COMPARATOR
TPMxC0VH:TPMxC0VL
CH0F
INTERRUPT
LOGIC
16-BIT LATCH
CH0IE
MS0B
MS0A
ELS1B ELS1A
CHANNEL 1
16-BIT COMPARATOR
TPMxC1VH:TPMxC1VL
16-BIT LATCH
TPMxCH1
PORT
LOGIC
CH1F
INTERRUPT
LOGIC
CH1IE
MS1B
MS1A
ELSnB ELSnA
CHANNEL n
TPMxCHn
PORT
LOGIC
16-BIT COMPARATOR
TPMxCnVH:TPMxCnVL
CHnF
INTERRUPT
LOGIC
16-BIT LATCH
CHnIE
MSnA
MSnB
Figure 10-2. TPM Block Diagram
The central component of the TPM is the 16-bit counter that can operate as a free-running counter, a
modulo counter, or an up-/down-counter when the TPM is configured for center-aligned PWM. The TPM
counter (when operating in normal up-counting mode) provides the timing reference for the input capture,
output compare, and edge-aligned PWM functions. The timer counter modulo registers,
TPMxMODH:TPMxMODL, control the modulo value of the counter. (The values 0x0000 or 0xFFFF
effectively make the counter free running.) Software can read the counter value at any time without
affecting the counting sequence. Any write to either byte of the TPMxCNT counter resets the counter
regardless of the data value written.
MC9S08AW60 Data Sheet, Rev 2
168
Freescale Semiconductor
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
All TPM channels are programmable independently as input capture, output compare, or buffered
edge-aligned PWM channels.
10.3 External Signal Description
When any pin associated with the timer is configured as a timer input, a passive pullup can be enabled.
After reset, the TPM modules are disabled and all pins default to general-purpose inputs with the passive
pullups disabled.
10.3.1 External TPM Clock Sources
When control bits CLKSB:CLKSA in the timer status and control register are set to 1:1, the prescaler and
consequently the 16-bit counter for TPMx are driven by an external clock source, TPMxCLK, connected
to an I/O pin. A synchronizer is needed between the external clock and the rest of the TPM. This
synchronizer is clocked by the bus clock so the frequency of the external source must be less than one-half
the frequency of the bus rate clock. The upper frequency limit for this external clock source is specified to
be one-fourth the bus frequency to conservatively accommodate duty cycle and phase-locked loop (PLL)
or frequency-locked loop (FLL) frequency jitter effects.
On some devices the external clock input is shared with one of the TPM channels. When a TPM channel
is shared as the external clock input, the associated TPM channel cannot use the pin. (The channel can still
be used in output compare mode as a software timer.) Also, if one of the TPM channels is used as the
external clock input, the corresponding ELSnB:ELSnA control bits must be set to 0:0 so the channel is not
trying to use the same pin.
10.3.2 TPMxCHn — TPMx Channel n I/O Pins
Each TPM channel is associated with an I/O pin on the MCU. The function of this pin depends on the
configuration of the channel. In some cases, no pin function is needed so the pin reverts to being controlled
by general-purpose I/O controls. When a timer has control of a port pin, the port data and data direction
registers do not affect the related pin(s). See the Pins and Connections chapter for additional information
about shared pin functions.
10.4 Register Definition
The TPM includes:
•
•
•
An 8-bit status and control register (TPMxSC)
A 16-bit counter (TPMxCNTH:TPMxCNTL)
A 16-bit modulo register (TPMxMODH:TPMxMODL)
Each timer channel has:
•
•
An 8-bit status and control register (TPMxCnSC)
A 16-bit channel value register (TPMxCnVH:TPMxCnVL)
Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address
assignments for all TPM registers. This section refers to registers and control bits only by their names. A
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
169
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
Freescale-provided equate or header file is used to translate these names into the appropriate absolute
addresses.
Some MCU systems have more than one TPM, so register names include placeholder characters to identify
which TPM and which channel is being referenced. For example, TPMxCnSC refers to timer (TPM) x,
channel n and TPM1C2SC is the status and control register for timer 1, channel 2.
10.4.1 Timer x Status and Control Register (TPMxSC)
TPMxSC contains the overflow status flag and control bits that are used to configure the interrupt enable,
TPM configuration, clock source, and prescale divisor. These controls relate to all channels within this
timer module.
7
6
5
4
3
2
1
0
R
W
TOF
TOIE
CPWMS
CLKSB
CLKSA
PS2
PS1
PS0
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 10-3. Timer x Status and Control Register (TPMxSC)
Table 10-1. TPMxSC Register Field Descriptions
Description
Field
7
TOF
Timer Overflow Flag — This flag is set when the TPM counter changes to 0x0000 after reaching the modulo
value programmed in the TPM counter modulo registers. When the TPM is configured for CPWM, TOF is set
after the counter has reached the value in the modulo register, at the transition to the next lower count value.
Clear TOF by reading the TPM status and control register when TOF is set and then writing a 0 to TOF. If another
TPM overflow occurs before the clearing sequence is complete, the sequence is reset so TOF would remain set
after the clear sequence was completed for the earlier TOF. Reset clears TOF. Writing a 1 to TOF has no effect.
0 TPM counter has not reached modulo value or overflow
1 TPM counter has overflowed
6
Timer Overflow Interrupt Enable — This read/write bit enables TPM overflow interrupts. If TOIE is set, an
interrupt is generated when TOF equals 1. Reset clears TOIE.
0 TOF interrupts inhibited (use software polling)
TOIE
1 TOF interrupts enabled
5
Center-Aligned PWM Select — This read/write bit selects CPWM operating mode. Reset clears this bit so the
TPM operates in up-counting mode for input capture, output compare, and edge-aligned PWM functions. Setting
CPWMS reconfigures the TPM to operate in up-/down-counting mode for CPWM functions. Reset clears
CPWMS.
CPWMS
0 All TPMx channels operate as input capture, output compare, or edge-aligned PWM mode as selected by the
MSnB:MSnA control bits in each channel’s status and control register
1 All TPMx channels operate in center-aligned PWM mode
4:3
Clock Source Select — As shown in Table 10-2, this 2-bit field is used to disable the TPM system or select one
CLKS[B:A] of three clock sources to drive the counter prescaler. The external source and the XCLK are synchronized to the
bus clock by an on-chip synchronization circuit.
2:0
PS[2:0]
Prescale Divisor Select — This 3-bit field selects one of eight divisors for the TPM clock input as shown in
Table 10-3. This prescaler is located after any clock source synchronization or clock source selection, so it affects
whatever clock source is selected to drive the TPM system.
MC9S08AW60 Data Sheet, Rev 2
170
Freescale Semiconductor
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
Table 10-2. TPM Clock Source Selection
CLKSB:CLKSA
TPM Clock Source to Prescaler Input
0:0
0:1
1:0
1:1
No clock selected (TPMx disabled)
Bus rate clock (BUSCLK)
Fixed system clock (XCLK)
External source (TPMxCLK)1,2
1
2
The maximum frequency that is allowed as an external clock is one-fourth of the bus
frequency.
If the external clock input is shared with channel n and is selected as the TPM clock source,
the corresponding ELSnB:ELSnA control bits should be set to 0:0 so channel n does not try
to use the same pin for a conflicting function.
Table 10-3. Prescale Divisor Selection
PS2:PS1:PS0
TPM Clock Source Divided-By
0:0:0
0:0:1
0:1:0
0:1:1
1:0:0
1:0:1
1:1:0
1:1:1
1
2
4
8
16
32
64
128
10.4.2 Timer x Counter Registers (TPMxCNTH:TPMxCNTL)
The two read-only TPM counter registers contain the high and low bytes of the value in the TPM counter.
Reading either byte (TPMxCNTH or TPMxCNTL) latches the contents of both bytes into a buffer where
they remain latched until the other byte is read. This allows coherent 16-bit reads in either order. The
coherency mechanism is automatically restarted by an MCU reset, a write of any value to TPMxCNTH or
TPMxCNTL, or any write to the timer status/control register (TPMxSC).
Reset clears the TPM counter registers.
7
6
5
4
3
2
1
0
R
W
Bit 15
14
13
12
11
10
9
Bit 8
Any write to TPMxCNTH clears the 16-bit counter.
Reset
0
0
0
0
0
0
0
0
Figure 10-4. Timer x Counter Register High (TPMxCNTH)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
171
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
7
6
5
4
3
2
1
0
R
W
Bit 7
6
5
4
3
2
1
Bit 0
Any write to TPMxCNTL clears the 16-bit counter.
Reset
0
0
0
0
0
0
0
0
Figure 10-5. Timer x Counter Register Low (TPMxCNTL)
When background mode is active, the timer counter and the coherency mechanism are frozen such that the
buffer latches remain in the state they were in when the background mode became active even if one or
both bytes of the counter are read while background mode is active.
10.4.3 Timer x Counter Modulo Registers (TPMxMODH:TPMxMODL)
The read/write TPM modulo registers contain the modulo value for the TPM counter. After the TPM
counter reaches the modulo value, the TPM counter resumes counting from 0x0000 at the next clock
(CPWMS = 0) or starts counting down (CPWMS = 1), and the overflow flag (TOF) becomes set. Writing
to TPMxMODH or TPMxMODL inhibits TOF and overflow interrupts until the other byte is written. Reset
sets the TPM counter modulo registers to 0x0000, which results in a free-running timer counter (modulo
disabled).
7
6
5
4
3
2
1
0
R
W
Bit 15
14
13
12
11
10
9
Bit 8
Reset
0
0
0
0
0
0
0
0
Figure 10-6. Timer x Counter Modulo Register High (TPMxMODH)
7
6
5
4
3
2
1
0
R
W
Bit 7
6
5
4
3
2
1
Bit 0
Reset
0
0
0
0
0
0
0
0
Figure 10-7. Timer x Counter Modulo Register Low (TPMxMODL)
It is good practice to wait for an overflow interrupt so both bytes of the modulo register can be written well
before a new overflow. An alternative approach is to reset the TPM counter before writing to the TPM
modulo registers to avoid confusion about when the first counter overflow will occur.
MC9S08AW60 Data Sheet, Rev 2
172
Freescale Semiconductor
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
10.4.4 Timer x Channel n Status and Control Register (TPMxCnSC)
TPMxCnSC contains the channel interrupt status flag and control bits that are used to configure the
interrupt enable, channel configuration, and pin function.
7
6
5
4
3
2
1
0
R
W
0
0
CHnF
CHnIE
MSnB
MSnA
ELSnB
ELSnA
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 10-8. Timer x Channel n Status and Control Register (TPMxCnSC)
Table 10-4. TPMxCnSC Register Field Descriptions
Description
Field
7
Channel n Flag — When channel n is configured for input capture, this flag bit is set when an active edge occurs
on the channel n pin. When channel n is an output compare or edge-aligned PWM channel, CHnF is set when
the value in the TPM counter registers matches the value in the TPM channel n value registers. This flag is
seldom used with center-aligned PWMs because it is set every time the counter matches the channel value
register, which correspond to both edges of the active duty cycle period.
CHnF
A corresponding interrupt is requested when CHnF is set and interrupts are enabled (CHnIE = 1). Clear CHnF
by reading TPMxCnSC while CHnF is set and then writing a 0 to CHnF. If another interrupt request occurs before
the clearing sequence is complete, the sequence is reset so CHnF would remain set after the clear sequence
was completed for the earlier CHnF. This is done so a CHnF interrupt request cannot be lost by clearing a
previous CHnF. Reset clears CHnF. Writing a 1 to CHnF has no effect.
0 No input capture or output compare event occurred on channel n
1 Input capture or output compare event occurred on channel n
6
Channel n Interrupt Enable — This read/write bit enables interrupts from channel n. Reset clears CHnIE.
0 Channel n interrupt requests disabled (use software polling)
CHnIE
1 Channel n interrupt requests enabled
5
Mode Select B for TPM Channel n — When CPWMS = 0, MSnB = 1 configures TPM channel n for
MSnB
edge-aligned PWM mode. For a summary of channel mode and setup controls, refer to Table 10-5.
4
Mode Select A for TPM Channel n — When CPWMS = 0 and MSnB = 0, MSnA configures TPM channel n for
input capture mode or output compare mode. Refer to Table 10-5 for a summary of channel mode and setup
controls.
MSnA
3:2
Edge/Level Select Bits — Depending on the operating mode for the timer channel as set by
ELSn[B:A] CPWMS:MSnB:MSnA and shown in Table 10-5, these bits select the polarity of the input edge that triggers an
input capture event, select the level that will be driven in response to an output compare match, or select the
polarity of the PWM output.
Setting ELSnB:ELSnA to 0:0 configures the related timer pin as a general-purpose I/O pin unrelated to any timer
channel functions. This function is typically used to temporarily disable an input capture channel or to make the
timer pin available as a general-purpose I/O pin when the associated timer channel is set up as a software timer
that does not require the use of a pin.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
173
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
Table 10-5. Mode, Edge, and Level Selection
CPWMS
MSnB:MSnA
ELSnB:ELSnA
Mode
Configuration
X
XX
00
Pin not used for TPM channel; use as an external clock for the TPM or
revert to general-purpose I/O
0
00
01
01
10
11
00
01
10
11
10
X1
10
X1
Input capture
Capture on rising edge only
Capture on falling edge only
Capture on rising or falling edge
Software compare only
Output
compare
Toggle output on compare
Clear output on compare
Set output on compare
1X
XX
Edge-aligned
PWM
High-true pulses (clear output on compare)
Low-true pulses (set output on compare)
1
Center-aligned High-true pulses (clear output on compare-up)
PWM
Low-true pulses (set output on compare-up)
If the associated port pin is not stable for at least two bus clock cycles before changing to input capture
mode, it is possible to get an unexpected indication of an edge trigger. Typically, a program would clear
status flags after changing channel configuration bits and before enabling channel interrupts or using the
status flags to avoid any unexpected behavior.
10.4.5 Timer x Channel Value Registers (TPMxCnVH:TPMxCnVL)
These read/write registers contain the captured TPM counter value of the input capture function or the
output compare value for the output compare or PWM functions. The channel value registers are cleared
by reset.
7
6
5
4
3
2
1
0
R
W
Bit 15
14
13
12
11
10
9
Bit 8
Reset
0
0
0
0
0
0
0
0
Figure 10-9. Timer x Channel Value Register High (TPMxCnVH)
7
6
5
4
3
2
1
0
R
W
Bit 7
6
5
4
3
2
1
Bit 0
Reset
0
0
0
0
0
0
0
0
Figure 10-10. Timer Channel Value Register Low (TPMxCnVL)
In input capture mode, reading either byte (TPMxCnVH or TPMxCnVL) latches the contents of both bytes
into a buffer where they remain latched until the other byte is read. This latching mechanism also resets
(becomes unlatched) when the TPMxCnSC register is written.
MC9S08AW60 Data Sheet, Rev 2
174
Freescale Semiconductor
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
In output compare or PWM modes, writing to either byte (TPMxCnVH or TPMxCnVL) latches the value
into a buffer. When both bytes have been written, they are transferred as a coherent 16-bit value into the
timer channel value registers. This latching mechanism may be manually reset by writing to the
TPMxCnSC register.
This latching mechanism allows coherent 16-bit writes in either order, which is friendly to various
compiler implementations.
10.5 Functional Description
All TPM functions are associated with a main 16-bit counter that allows flexible selection of the clock
source and prescale divisor. A 16-bit modulo register also is associated with the main 16-bit counter in the
TPM. Each TPM channel is optionally associated with an MCU pin and a maskable interrupt function.
The TPM has center-aligned PWM capabilities controlled by the CPWMS control bit in TPMxSC. When
CPWMS is set to 1, timer counter TPMxCNT changes to an up-/down-counter and all channels in the
associated TPM act as center-aligned PWM channels. When CPWMS = 0, each channel can
independently be configured to operate in input capture, output compare, or buffered edge-aligned PWM
mode.
The following sections describe the main 16-bit counter and each of the timer operating modes (input
capture, output compare, edge-aligned PWM, and center-aligned PWM). Because details of pin operation
and interrupt activity depend on the operating mode, these topics are covered in the associated mode
sections.
10.5.1 Counter
All timer functions are based on the main 16-bit counter (TPMxCNTH:TPMxCNTL). This section
discusses selection of the clock source, up-counting vs. up-/down-counting, end-of-count overflow, and
manual counter reset.
After any MCU reset, CLKSB:CLKSA = 0:0 so no clock source is selected and the TPM is inactive.
Normally, CLKSB:CLKSA would be set to 0:1 so the bus clock drives the timer counter. The clock source
for each of the TPM can be independently selected to be off, the bus clock (BUSCLK), the fixed system
clock (XCLK), or an external input. The maximum frequency allowed for the external clock option is
one-fourth the bus rate. Refer to Section 10.4.1, “Timer x Status and Control Register (TPMxSC)” and
Table 10-2 for more information about clock source selection.
When the microcontroller is in active background mode, the TPM temporarily suspends all counting until
the microcontroller returns to normal user operating mode. During stop mode, all TPM clocks are stopped;
therefore, the TPM is effectively disabled until clocks resume. During wait mode, the TPM continues to
operate normally.
The main 16-bit counter has two counting modes. When center-aligned PWM is selected (CPWMS = 1),
the counter operates in up-/down-counting mode. Otherwise, the counter operates as a simple up-counter.
As an up-counter, the main 16-bit counter counts from 0x0000 through its terminal count and then
continues with 0x0000. The terminal count is 0xFFFF or a modulus value in TPMxMODH:TPMxMODL.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
175
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
When center-aligned PWM operation is specified, the counter counts upward from 0x0000 through its
terminal count and then counts downward to 0x0000 where it returns to up-counting. Both 0x0000 and the
terminal count value (value in TPMxMODH:TPMxMODL) are normal length counts (one timer clock
period long).
An interrupt flag and enable are associated with the main 16-bit counter. The timer overflow flag (TOF) is
a software-accessible indication that the timer counter has overflowed. The enable signal selects between
software polling (TOIE = 0) where no hardware interrupt is generated, or interrupt-driven operation
(TOIE = 1) where a static hardware interrupt is automatically generated whenever the TOF flag is 1.
The conditions that cause TOF to become set depend on the counting mode (up or up/down). In
up-counting mode, the main 16-bit counter counts from 0x0000 through 0xFFFF and overflows to 0x0000
on the next counting clock. TOF becomes set at the transition from 0xFFFF to 0x0000. When a modulus
limit is set, TOF becomes set at the transition from the value set in the modulus register to 0x0000. When
the main 16-bit counter is operating in up-/down-counting mode, the TOF flag gets set as the counter
changes direction at the transition from the value set in the modulus register and the next lower count value.
This corresponds to the end of a PWM period. (The 0x0000 count value corresponds to the center of a
period.)
Because the HCS08 MCU is an 8-bit architecture, a coherency mechanism is built into the timer counter
for read operations. Whenever either byte of the counter is read (TPMxCNTH or TPMxCNTL), both bytes
are captured into a buffer so when the other byte is read, the value will represent the other byte of the count
at the time the first byte was read. The counter continues to count normally, but no new value can be read
from either byte until both bytes of the old count have been read.
The main timer counter can be reset manually at any time by writing any value to either byte of the timer
count TPMxCNTH or TPMxCNTL. Resetting the counter in this manner also resets the coherency
mechanism in case only one byte of the counter was read before resetting the count.
10.5.2 Channel Mode Selection
Provided CPWMS = 0 (center-aligned PWM operation is not specified), the MSnB and MSnA control bits
in the channel n status and control registers determine the basic mode of operation for the corresponding
channel. Choices include input capture, output compare, and buffered edge-aligned PWM.
10.5.2.1 Input Capture Mode
With the input capture function, the TPM can capture the time at which an external event occurs. When an
active edge occurs on the pin of an input capture channel, the TPM latches the contents of the TPM counter
into the channel value registers (TPMxCnVH:TPMxCnVL). Rising edges, falling edges, or any edge may
be chosen as the active edge that triggers an input capture.
When either byte of the 16-bit capture register is read, both bytes are latched into a buffer to support
coherent 16-bit accesses regardless of order. The coherency sequence can be manually reset by writing to
the channel status/control register (TPMxCnSC).
An input capture event sets a flag bit (CHnF) that can optionally generate a CPU interrupt request.
MC9S08AW60 Data Sheet, Rev 2
176
Freescale Semiconductor
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
10.5.2.2 Output Compare Mode
With the output compare function, the TPM can generate timed pulses with programmable position,
polarity, duration, and frequency. When the counter reaches the value in the channel value registers of an
output compare channel, the TPM can set, clear, or toggle the channel pin.
In output compare mode, values are transferred to the corresponding timer channel value registers only
after both 8-bit bytes of a 16-bit register have been written. This coherency sequence can be manually reset
by writing to the channel status/control register (TPMxCnSC).
An output compare event sets a flag bit (CHnF) that can optionally generate a CPU interrupt request.
10.5.2.3 Edge-Aligned PWM Mode
This type of PWM output uses the normal up-counting mode of the timer counter (CPWMS = 0) and can
be used when other channels in the same TPM are configured for input capture or output compare
functions. The period of this PWM signal is determined by the setting in the modulus register
(TPMxMODH:TPMxMODL). The duty cycle is determined by the setting in the timer channel value
register (TPMxCnVH:TPMxCnVL). The polarity of this PWM signal is determined by the setting in the
ELSnA control bit. Duty cycle cases of 0 percent and 100 percent are possible.
As Figure 10-11 shows, the output compare value in the TPM channel registers determines the pulse width
(duty cycle) of the PWM signal. The time between the modulus overflow and the output compare is the
pulse width. If ELSnA = 0, the counter overflow forces the PWM signal high and the output compare
forces the PWM signal low. If ELSnA = 1, the counter overflow forces the PWM signal low and the output
compare forces the PWM signal high.
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
PULSE
WIDTH
TPMxC
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
Figure 10-11. PWM Period and Pulse Width (ELSnA = 0)
When the channel value register is set to 0x0000, the duty cycle is 0 percent. By setting the timer channel
value register (TPMxCnVH:TPMxCnVL) to a value greater than the modulus setting, 100% duty cycle
can be achieved. This implies that the modulus setting must be less than 0xFFFF to get 100% duty cycle.
Because the HCS08 is a family of 8-bit MCUs, the settings in the timer channel registers are buffered to
ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to either register,
TPMxCnVH or TPMxCnVL, write to buffer registers. In edge-PWM mode, values are transferred to the
corresponding timer channel registers only after both 8-bit bytes of a 16-bit register have been written and
the value in the TPMxCNTH:TPMxCNTL counter is 0x0000. (The new duty cycle does not take effect
until the next full period.)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
177
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
10.5.3 Center-Aligned PWM Mode
This type of PWM output uses the up-/down-counting mode of the timer counter (CPWMS = 1). The
output compare value in TPMxCnVH:TPMxCnVL determines the pulse width (duty cycle) of the PWM
signal and the period is determined by the value in TPMxMODH:TPMxMODL.
TPMxMODH:TPMxMODL should be kept in the range of 0x0001 to 0x7FFF because values outside this
range can produce ambiguous results. ELSnA will determine the polarity of the CPWM output.
pulse width = 2 x (TPMxCnVH:TPMxCnVL)
Eqn. 10-1
period = 2 x (TPMxMODH:TPMxMODL);
for TPMxMODH:TPMxMODL = 0x0001–0x7FFF
Eqn. 10-2
If the channel value register TPMxCnVH:TPMxCnVL is zero or negative (bit 15 set), the duty cycle will
be 0%. If TPMxCnVH:TPMxCnVL is a positive value (bit 15 clear) and is greater than the (nonzero)
modulus setting, the duty cycle will be 100% because the duty cycle compare will never occur. This
implies the usable range of periods set by the modulus register is 0x0001 through 0x7FFE (0x7FFF if
generation of 100% duty cycle is not necessary). This is not a significant limitation because the resulting
period is much longer than required for normal applications.
TPMxMODH:TPMxMODL = 0x0000 is a special case that should not be used with center-aligned PWM
mode. When CPWMS = 0, this case corresponds to the counter running free from 0x0000 through
0xFFFF, but when CPWMS = 1 the counter needs a valid match to the modulus register somewhere other
than at 0x0000 in order to change directions from up-counting to down-counting.
Figure 10-12 shows the output compare value in the TPM channel registers (multiplied by 2), which
determines the pulse width (duty cycle) of the CPWM signal. If ELSnA = 0, the compare match while
counting up forces the CPWM output signal low and a compare match while counting down forces the
output high. The counter counts up until it reaches the modulo setting in TPMxMODH:TPMxMODL, then
counts down until it reaches zero. This sets the period equal to two times TPMxMODH:TPMxMODL.
COUNT = 0
OUTPUT
COMPARE
(COUNT UP)
OUTPUT
COMPARE
(COUNT DOWN)
COUNT =
TPMxMODH:TPMx
COUNT =
TPMxMODH:TPMx
TPM1C
PULSE WIDTH
PERIOD
2 x
2 x
Figure 10-12. CPWM Period and Pulse Width (ELSnA = 0)
Center-aligned PWM outputs typically produce less noise than edge-aligned PWMs because fewer I/O pin
transitions are lined up at the same system clock edge. This type of PWM is also required for some types
of motor drives.
Because the HCS08 is a family of 8-bit MCUs, the settings in the timer channel registers are buffered to
ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers,
TPMxMODH, TPMxMODL, TPMxCnVH, and TPMxCnVL, actually write to buffer registers. Values are
MC9S08AW60 Data Sheet, Rev 2
178
Freescale Semiconductor
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
transferred to the corresponding timer channel registers only after both 8-bit bytes of a 16-bit register have
been written and the timer counter overflows (reverses direction from up-counting to down-counting at the
end of the terminal count in the modulus register). This TPMxCNT overflow requirement only applies to
PWM channels, not output compares.
Optionally, when TPMxCNTH:TPMxCNTL = TPMxMODH:TPMxMODL, the TPM can generate a TOF
interrupt at the end of this count. The user can choose to reload any number of the PWM buffers, and they
will all update simultaneously at the start of a new period.
Writing to TPMxSC cancels any values written to TPMxMODH and/or TPMxMODL and resets the
coherency mechanism for the modulo registers. Writing to TPMxCnSC cancels any values written to the
channel value registers and resets the coherency mechanism for TPMxCnVH:TPMxCnVL.
10.6 TPM Interrupts
The TPM generates an optional interrupt for the main counter overflow and an interrupt for each channel.
The meaning of channel interrupts depends on the mode of operation for each channel. If the channel is
configured for input capture, the interrupt flag is set each time the selected input capture edge is
recognized. If the channel is configured for output compare or PWM modes, the interrupt flag is set each
time the main timer counter matches the value in the 16-bit channel value register. See the Resets,
Interrupts, and System Configuration chapter for absolute interrupt vector addresses, priority, and local
interrupt mask control bits.
For each interrupt source in the TPM, a flag bit is set on recognition of the interrupt condition such as timer
overflow, channel input capture, or output compare events. This flag may be read (polled) by software to
verify that the action has occurred, or an associated enable bit (TOIE or CHnIE) can be set to enable
hardware interrupt generation. While the interrupt enable bit is set, a static interrupt will be generated
whenever the associated interrupt flag equals 1. It is the responsibility of user software to perform a
sequence of steps to clear the interrupt flag before returning from the interrupt service routine.
10.6.1 Clearing Timer Interrupt Flags
TPM interrupt flags are cleared by a 2-step process that includes a read of the flag bit while it is set (1)
followed by a write of 0 to the bit. If a new event is detected between these two steps, the sequence is reset
and the interrupt flag remains set after the second step to avoid the possibility of missing the new event.
10.6.2 Timer Overflow Interrupt Description
The conditions that cause TOF to become set depend on the counting mode (up or up/down). In
up-counting mode, the 16-bit timer counter counts from 0x0000 through 0xFFFF and overflows to 0x0000
on the next counting clock. TOF becomes set at the transition from 0xFFFF to 0x0000. When a modulus
limit is set, TOF becomes set at the transition from the value set in the modulus register to 0x0000. When
the counter is operating in up-/down-counting mode, the TOF flag gets set as the counter changes direction
at the transition from the value set in the modulus register and the next lower count value. This corresponds
to the end of a PWM period. (The 0x0000 count value corresponds to the center of a period.)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
179
Chapter 10 Timer/Pulse-Width Modulator (S08TPMV2)
10.6.3 Channel Event Interrupt Description
The meaning of channel interrupts depends on the current mode of the channel (input capture, output
compare, edge-aligned PWM, or center-aligned PWM).
When a channel is configured as an input capture channel, the ELSnB:ELSnA control bits select rising
edges, falling edges, any edge, or no edge (off) as the edge that triggers an input capture event. When the
selected edge is detected, the interrupt flag is set. The flag is cleared by the 2-step sequence described in
Section 10.6.1, “Clearing Timer Interrupt Flags.”
When a channel is configured as an output compare channel, the interrupt flag is set each time the main
timer counter matches the 16-bit value in the channel value register. The flag is cleared by the 2-step
sequence described in Section 10.6.1, “Clearing Timer Interrupt Flags.”
10.6.4 PWM End-of-Duty-Cycle Events
For channels that are configured for PWM operation, there are two possibilities:
•
When the channel is configured for edge-aligned PWM, the channel flag is set when the timer
counter matches the channel value register that marks the end of the active duty cycle period.
•
When the channel is configured for center-aligned PWM, the timer count matches the channel
value register twice during each PWM cycle. In this CPWM case, the channel flag is set at the start
and at the end of the active duty cycle, which are the times when the timer counter matches the
channel value register.
The flag is cleared by the 2-step sequence described in Section 10.6.1, “Clearing Timer Interrupt Flags.”
MC9S08AW60 Data Sheet, Rev 2
180
Freescale Semiconductor
Chapter 11
Serial Communications Interface (S08SCIV2)
11.1 Introduction
The MC9S08AW60 Series includes two independent serial communications interface (SCI) modules
which are sometimes called universal asynchronous receiver/transmitters (UARTs). Typically, these
systems are used to connect to the RS232 serial input/output (I/O) port of a personal computer or
workstation, but they can also be used to communicate with other embedded controllers.
A flexible, 13-bit, modulo-based baud rate generator supports a broad range of standard baud rates beyond
115.2 kbaud. Transmit and receive within the same SCI use a common baud rate, and each SCI module
has a separate baud rate generator.
This SCI system offers many advanced features not commonly found on other asynchronous serial I/O
peripherals on other embedded controllers. The receiver employs an advanced data sampling technique
that ensures reliable communication and noise detection. Hardware parity, receiver wakeup, and double
buffering on transmit and receive are also included.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
181
Chapter 11 Serial Communications Interface (S08SCIV2)
HCS08 CORE
DEBUG
MODULE (DBG)
8
PTA7– PTA0
BKGD/MS
BDC
CPU
8
PTB7/AD1P7–
PTB0/AD1P0
HCS08 SYSTEM CONTROL
RESET
IRQ
PTC6
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
RxD2
TxD2
PTC5/RxD2
PTC4
PTC3/TxD2
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI2)
PTC2/MCLK
PTC1/SDA1
SDA1
SCL1
RTI
COP
LVD
IIC MODULE (IIC1)
PTC0/SCL1
IRQ
AD1P7–AD1P0
8
V
DDAD
8
10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC1)
AD1P15–AD1P8
V
SSAD
V
REFL
PTD7/AD1P15/KBI1P7
PTD6/AD1P14/TPM1CLK
PTD5/AD1P13
PTD4/AD1P12/TPM2CLK
PTD3/AD1P11/KBI1P6
PTD2/AD1P10/KBI1P5
PTD1/AD1P9
V
REFH
USER FLASH
(AW60 = 63,280 BYTES)
(AW48 = 49,152 BYTES)
(AW32 = 32,768 BYTES)
(AW16 = 16,384 BYTES)
PTD0/AD1P8
SPSCK1
PTE7/SPSCK1
PTE6/MOSI1
MOSI1
SERIAL PERIPHERAL
USER RAM
MISO1
SS1
INTERFACE MODULE (SPI1)
PTE5/MISO1
PTE4/SS1
AW60/48/32 = 2048 BYTES
AW16 = 1024 BYTES
TPM1CLK
PTE3/TPM1CH1
PTE2/TPM1CH0
6-CHANNEL TIMER/PWM
MODULE (TPM1)
TPM1CH5–
TPM1CH0
INTERNAL CLOCK
GENERATOR (ICG)
6
RxD1
TxD1
PTE1/RxD1
PTE0/TxD1
PTF7
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI1)
LOW-POWER OSCILLATOR
PTF6
PTF5/TPM2CH1
PTF4/TPM2CH0
TPM2CLK
V
DD
VOLTAGE
REGULATOR
2-CHANNEL TIMER/PWM
MODULE (TPM2)
TPM2CH1–TPM2CH0
V
SS
2
PTF3/TPM1CH5
KBI1P7–KBI1P5
3
PTF2/TPM1CH4
PTF1/TPM1CH3
PTF0/TPM1CH2
8-BIT KEYBOARD
INTERRUPT MODULE (KBI1)
KBI1P4–KBI1P0
5
EXTAL
XTAL
PTG6/EXTAL
PTG5/XTAL
NOTES:
PTG4/KBI1P4
PTG3/KBI1P3
PTG2/KBI1P2
PTG1/KBI1P1
PTG0/KBI1P0
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software configurable pullup/pulldown device if IRQ is enabled
(IRQPE = 1). Pulldown is enabled if rising edge detect is selected (IRQEDG = 1)
3. IRQ does not have a clamp diode to VDD. IRQ should not be driven above VDD
4. Pin contains integrated pullup device.
.
5. Pins PTD7, PTD3, PTD2, and PTG4 contain both pullup and pulldown devices.
Pulldown enabled when KBI is enabled (KBIPEn = 1) and rising edge is selected
(KBEDGn = 1).
Figure 11-1. Block Diagram Highlighting the SCI Modules
MC9S08AW60 Data Sheet, Rev 2
182
Freescale Semiconductor
Chapter 11 Serial Communications Interface (S08SCIV2)
11.1.1 Features
Features of SCI module include:
•
•
•
•
Full-duplex, standard non-return-to-zero (NRZ) format
Double-buffered transmitter and receiver with separate enables
Programmable baud rates (13-bit modulo divider)
Interrupt-driven or polled operation:
— Transmit data register empty and transmission complete
— Receive data register full
— Receive overrun, parity error, framing error, and noise error
— Idle receiver detect
•
•
•
•
•
Hardware parity generation and checking
Programmable 8-bit or 9-bit character length
Receiver wakeup by idle-line or address-mark
Optional 13-bit break character
Selectable transmitter output polarity
11.1.2 Modes of Operation
See Section 11.3, “Functional Description,” for a detailed description of SCI operation in the different
modes.
•
•
•
•
8- and 9-bit data modes
Stop modes — SCI is halted during all stop modes
Loop mode
Single-wire mode
11.1.3 Block Diagram
Figure 11-2 shows the transmitter portion of the SCI.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
183
Chapter 11 Serial Communications Interface (S08SCIV2)
INTERNAL BUS
(WRITE-ONLY)
LOOPS
RSRC
SCID – Tx BUFFER
LOOP
CONTROL
TO RECEIVE
DATA IN
M
11-BIT TRANSMIT SHIFT REGISTER
H
8
7
6
5
4
3
2
1
0
L
TO TxD PIN
1 × BAUD
RATE CLOCK
SHIFT DIRECTION
TXINV
T8
PE
PT
PARITY
GENERATION
SCI CONTROLS TxD
TxD DIRECTION
TE
SBK
TO TxD
TRANSMIT CONTROL
PIN LOGIC
TXDIR
BRK13
TDRE
TIE
Tx INTERRUPT
REQUEST
TC
TCIE
Figure 11-2. SCI Transmitter Block Diagram
MC9S08AW60 Data Sheet, Rev 2
184
Freescale Semiconductor
Chapter 11 Serial Communications Interface (S08SCIV2)
Figure 11-3 shows the receiver portion of the SCI.
INTERNAL BUS
(READ-ONLY)
SCID – Rx BUFFER
DIVIDE
BY 16
16 × BAUD
RATE CLOCK
M
11-BIT RECEIVE SHIFT REGISTER
H
8
7
6
5
4
3
2
1
0
L
DATA RECOVERY
FROM RxD PIN
SHIFT DIRECTION
LOOPS
RSRC
WAKE
SINGLE-WIRE
LOOP CONTROL
WAKEUP
LOGIC
RWU
ILT
FROM
TRANSMITTER
RDRF
RIE
Rx INTERRUPT
REQUEST
IDLE
ILIE
OR
ORIE
FE
FEIE
ERROR INTERRUPT
REQUEST
NF
NEIE
PE
PT
PARITY
CHECKING
PF
PEIE
Figure 11-3. SCI Receiver Block Diagram
11.2 Register Definition
The SCI has eight 8-bit registers to control baud rate, select SCI options, report SCI status, and for
transmit/receive data.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
185
Chapter 11 Serial Communications Interface (S08SCIV2)
Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address
assignments for all SCI registers. This section refers to registers and control bits only by their names. A
Freescale-provided equate or header file is used to translate these names into the appropriate absolute
addresses.
11.2.1 SCI Baud Rate Registers (SCIxBDH, SCIxBHL)
This pair of registers controls the prescale divisor for SCI baud rate generation. To update the 13-bit baud
rate setting [SBR12:SBR0], first write to SCIxBDH to buffer the high half of the new value and then write
to SCIxBDL. The working value in SCIxBDH does not change until SCIxBDL is written.
SCIxBDL is reset to a non-zero value, so after reset the baud rate generator remains disabled until the first
time the receiver or transmitter is enabled (RE or TE bits in SCIxC2 are written to 1).
7
6
5
4
3
2
1
0
R
W
0
0
0
SBR12
SBR11
SBR10
SBR9
SBR8
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 11-4. SCI Baud Rate Register (SCIxBDH)
Table 11-1. SCIxBDH Register Field Descriptions
Description
Field
4:0
Baud Rate Modulo Divisor — These 13 bits are referred to collectively as BR, and they set the modulo divide
SBR[12:8] rate for the SCI baud rate generator. When BR = 0, the SCI baud rate generator is disabled to reduce supply
current. When BR = 1 to 8191, the SCI baud rate = BUSCLK/(16×BR). See also BR bits in Table 11-2.
7
6
5
4
3
2
1
0
R
W
SBR7
SBR6
SBR5
SBR4
SBR3
SBR2
SBR1
SBR0
Reset
0
0
0
0
0
1
0
0
Figure 11-5. SCI Baud Rate Register (SCIxBDL)
Table 11-2. SCIxBDL Register Field Descriptions
Description
Field
4:0
Baud Rate Modulo Divisor — These 13 bits are referred to collectively as BR, and they set the modulo divide
SBR[12:8] rate for the SCI baud rate generator. When BR = 0, the SCI baud rate generator is disabled to reduce supply
current. When BR = 1 to 8191, the SCI baud rate = BUSCLK/(16×BR). See also BR bits in Table 11-1.
MC9S08AW60 Data Sheet, Rev 2
186
Freescale Semiconductor
Chapter 11 Serial Communications Interface (S08SCIV2)
11.2.2 SCI Control Register 1 (SCIxC1)
This read/write register is used to control various optional features of the SCI system.
7
6
5
4
3
2
1
0
R
W
LOOPS
SCISWAI
RSRC
M
WAKE
ILT
PE
PT
Reset
0
0
0
0
0
0
0
0
Figure 11-6. SCI Control Register 1 (SCIxC1)
Table 11-3. SCIxC1 Register Field Descriptions
Description
Field
7
Loop Mode Select — Selects between loop back modes and normal 2-pin full-duplex modes. When
LOOPS = 1, the transmitter output is internally connected to the receiver input.
0 Normal operation — RxD and TxD use separate pins.
LOOPS
1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input. (See
RSRC bit.) RxD pin is not used by SCI.
6
SCI Stops in Wait Mode
SCISWAI 0 SCI clocks continue to run in wait mode so the SCI can be the source of an interrupt that wakes up the CPU.
1 SCI clocks freeze while CPU is in wait mode.
5
Receiver Source Select — This bit has no meaning or effect unless the LOOPS bit is set to 1. When
LOOPS = 1, the receiver input is internally connected to the TxD pin and RSRC determines whether this
connection is also connected to the transmitter output.
RSRC
0 Provided LOOPS = 1, RSRC = 0 selects internal loop back mode and the SCI does not use the RxD or TxD
pins.
1 Single-wire SCI mode where the TxD pin is connected to the transmitter output and receiver input.
4
9-Bit or 8-Bit Mode Select
M
0 Normal — start + 8 data bits (LSB first) + stop.
1 Receiver and transmitter use 9-bit data characters
start + 8 data bits (LSB first) + 9th data bit + stop.
3
Receiver Wakeup Method Select — Refer to Section 11.3.3.2, “Receiver Wakeup Operation” for more
WAKE
information.
0 Idle-line wakeup.
1 Address-mark wakeup.
2
ILT
Idle Line Type Select — Setting this bit to 1 ensures that the stop bit and logic 1 bits at the end of a character
do not count toward the 10 or 11 bit times of the logic high level by the idle line detection logic. Refer to
Section 11.3.3.2.1, “Idle-Line Wakeup” for more information.
0 Idle character bit count starts after start bit.
1 Idle character bit count starts after stop bit.
1
PE
Parity Enable — Enables hardware parity generation and checking. When parity is enabled, the most significant
bit (MSB) of the data character (eighth or ninth data bit) is treated as the parity bit.
0 No hardware parity generation or checking.
1 Parity enabled.
0
Parity Type — Provided parity is enabled (PE = 1), this bit selects even or odd parity. Odd parity means the total
PT
number of 1s in the data character, including the parity bit, is odd. Even parity means the total number of 1s in
the data character, including the parity bit, is even.
0 Even parity.
1 Odd parity.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
187
Chapter 11 Serial Communications Interface (S08SCIV2)
11.2.3 SCI Control Register 2 (SCIxC2)
This register can be read or written at any time.
7
6
5
4
3
2
1
0
R
W
TIE
TCIE
RIE
ILIE
TE
RE
RWU
SBK
Reset
0
0
0
0
0
0
0
0
Figure 11-7. SCI Control Register 2 (SCIxC2)
Table 11-4. SCIxC2 Register Field Descriptions
Description
Field
7
Transmit Interrupt Enable (for TDRE)
TIE
0 Hardware interrupts from TDRE disabled (use polling).
1 Hardware interrupt requested when TDRE flag is 1.
6
Transmission Complete Interrupt Enable (for TC)
0 Hardware interrupts from TC disabled (use polling).
1 Hardware interrupt requested when TC flag is 1.
TCIE
5
Receiver Interrupt Enable (for RDRF)
RIE
0 Hardware interrupts from RDRF disabled (use polling).
1 Hardware interrupt requested when RDRF flag is 1.
4
Idle Line Interrupt Enable (for IDLE)
ILIE
0 Hardware interrupts from IDLE disabled (use polling).
1 Hardware interrupt requested when IDLE flag is 1.
3
TE
Transmitter Enable
0 Transmitter off.
1 Transmitter on.
TE must be 1 in order to use the SCI transmitter. Normally, when TE = 1, the SCI forces the TxD pin to act as an
output for the SCI system. If LOOPS = 1 and RSRC = 0, the TxD pin reverts to being a port B general-purpose
I/O pin even if TE = 1.
When the SCI is configured for single-wire operation (LOOPS = RSRC = 1), TXDIR controls the direction of
traffic on the single SCI communication line (TxD pin).
TE also can be used to queue an idle character by writing TE = 0 then TE = 1 while a transmission is in progress.
Refer to Section 11.3.2.1, “Send Break and Queued Idle” for more details.
When TE is written to 0, the transmitter keeps control of the port TxD pin until any data, queued idle, or queued
break character finishes transmitting before allowing the pin to revert to a general-purpose I/O pin.
2
Receiver Enable — When the SCI receiver is off, the RxD pin reverts to being a general-purpose port I/O pin.
RE
0 Receiver off.
1 Receiver on.
MC9S08AW60 Data Sheet, Rev 2
188
Freescale Semiconductor
Chapter 11 Serial Communications Interface (S08SCIV2)
Table 11-4. SCIxC2 Register Field Descriptions (continued)
Field
Description
1
Receiver Wakeup Control — This bit can be written to 1 to place the SCI receiver in a standby state where it
waits for automatic hardware detection of a selected wakeup condition. The wakeup condition is either an idle
line between messages (WAKE = 0, idle-line wakeup), or a logic 1 in the most significant data bit in a character
(WAKE = 1, address-mark wakeup). Application software sets RWU and (normally) a selected hardware
condition automatically clears RWU. Refer to Section 11.3.3.2, “Receiver Wakeup Operation” for more details.
0 Normal SCI receiver operation.
RWU
1 SCI receiver in standby waiting for wakeup condition.
0
SBK
Send Break — Writing a 1 and then a 0 to SBK queues a break character in the transmit data stream. Additional
break characters of 10 or 11 bit times of logic 0 are queued as long as SBK = 1. Depending on the timing of the
set and clear of SBK relative to the information currently being transmitted, a second break character may be
queued before software clears SBK. Refer to Section 11.3.2.1, “Send Break and Queued Idle” for more details.
0 Normal transmitter operation.
1 Queue break character(s) to be sent.
11.2.4 SCI Status Register 1 (SCIxS1)
This register has eight read-only status flags. Writes have no effect. Special software sequences (which do
not involve writing to this register) are used to clear these status flags.
7
6
5
4
3
2
1
0
R
W
TDRE
TC
RDRF
IDLE
OR
NF
FE
PF
Reset
1
1
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 11-8. SCI Status Register 1 (SCIxS1)
Table 11-5. SCIxS1 Register Field Descriptions
Description
Field
7
Transmit Data Register Empty Flag — TDRE is set out of reset and when a transmit data value transfers from
the transmit data buffer to the transmit shifter, leaving room for a new character in the buffer. To clear TDRE, read
SCIxS1 with TDRE = 1 and then write to the SCI data register (SCIxD).
0 Transmit data register (buffer) full.
TDRE
1 Transmit data register (buffer) empty.
6
TC
Transmission Complete Flag — TC is set out of reset and when TDRE = 1 and no data, preamble, or break
character is being transmitted.
0 Transmitter active (sending data, a preamble, or a break).
1 Transmitter idle (transmission activity complete).
TC is cleared automatically by reading SCIxS1 with TC = 1 and then doing one of the following three things:
• Write to the SCI data register (SCIxD) to transmit new data
• Queue a preamble by changing TE from 0 to 1
• Queue a break character by writing 1 to SBK in SCIxC2
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
189
Chapter 11 Serial Communications Interface (S08SCIV2)
Table 11-5. SCIxS1 Register Field Descriptions (continued)
Field
Description
5
Receive Data Register Full Flag — RDRF becomes set when a character transfers from the receive shifter into
the receive data register (SCIxD). In 8-bit mode, to clear RDRF, read SCIxS1 with RDRF = 1 and then read the
SCI data register (SCIxD). In 9-bit mode, to clear RDRF, read SCIxS1 with RDRF = 1 and then read SCIxD and
the SCI control 3 register (SCIxC3). SCIxD and SCIxC3 can be read in any order, but the flag is cleared only after
both data registers are read.
RDRF
0 Receive data register empty.
1 Receive data register full.
4
IDLE
Idle Line Flag — IDLE is set when the SCI receive line becomes idle for a full character time after a period of
activity. When ILT = 0, the receiver starts counting idle bit times after the start bit. So if the receive character is
all 1s, these bit times and the stop bit time count toward the full character time of logic high (10 or 11 bit times
depending on the M control bit) needed for the receiver to detect an idle line. When ILT = 1, the receiver doesn’t
start counting idle bit times until after the stop bit. So the stop bit and any logic high bit times at the end of the
previous character do not count toward the full character time of logic high needed for the receiver to detect an
idle line.
To clear IDLE, read SCIxS1 with IDLE = 1 and then read the SCI data register (SCIxD). After IDLE has been
cleared, it cannot become set again until after a new character has been received and RDRF has been set. IDLE
will get set only once even if the receive line remains idle for an extended period.
0 No idle line detected.
1 Idle line was detected.
3
OR
Receiver Overrun Flag — OR is set when a new serial character is ready to be transferred to the receive data
register (buffer), but the previously received character has not been read from SCIxD yet. In this case, the new
character (and all associated error information) is lost because there is no room to move it into SCIxD. To clear
OR, read SCIxS1 with OR = 1 and then read the SCI data register (SCIxD).
0 No overrun.
1 Receive overrun (new SCI data lost).
2
NF
Noise Flag — The advanced sampling technique used in the receiver takes seven samples during the start bit
and three samples in each data bit and the stop bit. If any of these samples disagrees with the rest of the samples
within any bit time in the frame, the flag NF will be set at the same time as the flag RDRF gets set for the
character. To clear NF, read SCIxS1 and then read the SCI data register (SCIxD).
0 No noise detected.
1 Noise detected in the received character in SCIxD.
1
FE
Framing Error Flag — FE is set at the same time as RDRF when the receiver detects a logic 0 where the stop
bit was expected. This suggests the receiver was not properly aligned to a character frame. To clear FE, read
SCIxS1 with FE = 1 and then read the SCI data register (SCIxD).
0 No framing error detected. This does not guarantee the framing is correct.
1 Framing error.
0
Parity Error Flag — PF is set at the same time as RDRF when parity is enabled (PE = 1) and the parity bit in
PF
the received character does not agree with the expected parity value. To clear PF, read SCIxS1 and then read
the SCI data register (SCIxD).
0 No parity error.
1 Parity error.
MC9S08AW60 Data Sheet, Rev 2
190
Freescale Semiconductor
Chapter 11 Serial Communications Interface (S08SCIV2)
11.2.5 SCI Status Register 2 (SCIxS2)
This register has one read-only status flag. Writes have no effect.
7
6
5
4
3
2
1
0
R
W
0
0
0
0
0
0
RAF
BRK13
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 11-9. SCI Status Register 2 (SCIxS2)
Table 11-6. SCIxS2 Register Field Descriptions
Description
Field
2
Break Character Length — BRK13 is used to select a longer break character length. Detection of a framing
error is not affected by the state of this bit.
BRK13
0 Break character is 10 bit times (11 if M = 1)
1 Break character is 13 bit times (14 if M = 1)
0
RAF
Receiver Active Flag — RAF is set when the SCI receiver detects the beginning of a valid start bit, and RAF is
cleared automatically when the receiver detects an idle line. This status flag can be used to check whether an
SCI character is being received before instructing the MCU to go to stop mode.
0 SCI receiver idle waiting for a start bit.
1 SCI receiver active (RxD input not idle).
11.2.6 SCI Control Register 3 (SCIxC3)
7
6
5
4
3
2
1
0
R
W
R8
T8
TXDIR
TXINV
ORIE
NEIE
FEIE
PEIE
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 11-10. SCI Control Register 3 (SCIxC3)
Table 11-7. SCIxC3 Register Field Descriptions
Description
Field
7
R8
Ninth Data Bit for Receiver — When the SCI is configured for 9-bit data (M = 1), R8 can be thought of as a
ninth receive data bit to the left of the MSB of the buffered data in the SCIxD register. When reading 9-bit data,
both R8 and SCIxD must be read to complete the automatic RDRF clearing sequence.
6
T8
Ninth Data Bit for Transmitter — When the SCI is configured for 9-bit data (M = 1), T8 may be thought of as a
ninth transmit data bit to the left of the MSB of the data in the SCIxD register. When writing 9-bit data, the entire
9-bit value is transferred to the SCI shift register after SCIxD is written so T8 should be written (if it needs to
change from its previous value) before SCIxD is written. If T8 does not need to change in the new value (such
as when it is used to generate mark or space parity), it need not be written each time SCIxD is written.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
191
Chapter 11 Serial Communications Interface (S08SCIV2)
Table 11-7. SCIxC3 Register Field Descriptions (continued)
Field
Description
5
TxD Pin Direction in Single-Wire Mode — When the SCI is configured for single-wire half-duplex operation
(LOOPS = RSRC = 1), this bit determines the direction of data at the TxD pin.
0 TxD pin is an input in single-wire mode.
TXDIR
1 TxD pin is an output in single-wire mode.
4
Transmit Data Inversion — Setting this bit reverses the polarity of the transmitted data output.
0 Transmit data not inverted
TXINV1
1 Transmit data inverted
3
Overrun Interrupt Enable — This bit enables the overrun flag (OR) to generate hardware interrupt requests.
0 OR interrupts disabled (use polling).
ORIE
1 Hardware interrupt requested when OR = 1.
2
Noise Error Interrupt Enable — This bit enables the noise flag (NF) to generate hardware interrupt requests.
0 NF interrupts disabled (use polling).
NEIE
1 Hardware interrupt requested when NF = 1.
1
Framing Error Interrupt Enable — This bit enables the framing error flag (FE) to generate hardware interrupt
FEIE
requests.
0 FE interrupts disabled (use polling).
1 Hardware interrupt requested when FE = 1.
0
Parity Error Interrupt Enable — This bit enables the parity error flag (PF) to generate hardware interrupt
PEIE
requests.
0 PF interrupts disabled (use polling).
1 Hardware interrupt requested when PF = 1.
1
Setting TXINV inverts the TxD output for all cases: data bits, start and stop bits, break, and idle.
11.2.7 SCI Data Register (SCIxD)
This register is actually two separate registers. Reads return the contents of the read-only receive data
buffer and writes go to the write-only transmit data buffer. Reads and writes of this register are also
involved in the automatic flag clearing mechanisms for the SCI status flags.
7
6
5
4
3
2
1
0
R
W
R7
R6
R5
R4
R3
R2
R1
R0
T7
0
T6
0
T5
0
T4
0
T3
0
T2
0
T1
0
T0
0
Reset
Figure 11-11. SCI Data Register (SCIxD)
11.3 Functional Description
The SCI allows full-duplex, asynchronous, NRZ serial communication among the MCU and remote
devices, including other MCUs. The SCI comprises a baud rate generator, transmitter, and receiver block.
The transmitter and receiver operate independently, although they use the same baud rate generator. During
normal operation, the MCU monitors the status of the SCI, writes the data to be transmitted, and processes
received data. The following describes each of the blocks of the SCI.
MC9S08AW60 Data Sheet, Rev 2
192
Freescale Semiconductor
Chapter 11 Serial Communications Interface (S08SCIV2)
11.3.1 Baud Rate Generation
As shown in Figure 11-12, the clock source for the SCI baud rate generator is the bus-rate clock.
MODULO DIVIDE BY
(1 THROUGH 8191)
DIVIDE BY
16
Tx BAUD RATE
BUSCLK
SBR12:SBR0
Rx SAMPLING CLOCK
BAUD RATE GENERATOR
OFF IF [SBR12:SBR0] = 0
(16 × BAUD RATE)
BUSCLK
BAUD RATE =
[SBR12:SBR0] × 16
Figure 11-12. SCI Baud Rate Generation
SCI communications require the transmitter and receiver (which typically derive baud rates from
independent clock sources) to use the same baud rate. Allowed tolerance on this baud frequency depends
on the details of how the receiver synchronizes to the leading edge of the start bit and how bit sampling is
performed.
The MCU resynchronizes to bit boundaries on every high-to-low transition, but in the worst case, there are
no such transitions in the full 10- or 11-bit time character frame so any mismatch in baud rate is
accumulated for the whole character time. For a Freescale Semiconductor SCI system whose bus
frequency is driven by a crystal, the allowed baud rate mismatch is about 4.5 percent for 8-bit data format
and about 4 percent for 9-bit data format. Although baud rate modulo divider settings do not always
produce baud rates that exactly match standard rates, it is normally possible to get within a few percent,
which is acceptable for reliable communications.
11.3.2 Transmitter Functional Description
This section describes the overall block diagram for the SCI transmitter, as well as specialized functions
for sending break and idle characters. The transmitter block diagram is shown in Figure 11-2.
The transmitter output (TxD) idle state defaults to logic high (TXINV = 0 following reset). The transmitter
output is inverted by setting TXINV = 1. The transmitter is enabled by setting the TE bit in SCIxC2. This
queues a preamble character that is one full character frame of the idle state. The transmitter then remains
idle until data is available in the transmit data buffer. Programs store data into the transmit data buffer by
writing to the SCI data register (SCIxD).
The central element of the SCI transmitter is the transmit shift register that is either 10 or 11 bits long
depending on the setting in the M control bit. For the remainder of this section, we will assume M = 0,
selecting the normal 8-bit data mode. In 8-bit data mode, the shift register holds a start bit, eight data bits,
and a stop bit. When the transmit shift register is available for a new SCI character, the value waiting in
the transmit data register is transferred to the shift register (synchronized with the baud rate clock) and the
transmit data register empty (TDRE) status flag is set to indicate another character may be written to the
transmit data buffer at SCIxD.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
193
Chapter 11 Serial Communications Interface (S08SCIV2)
If no new character is waiting in the transmit data buffer after a stop bit is shifted out the TxD pin, the
transmitter sets the transmit complete flag and enters an idle mode, with TxD high, waiting for more
characters to transmit.
Writing 0 to TE does not immediately release the pin to be a general-purpose I/O pin. Any transmit activity
that is in progress must first be completed. This includes data characters in progress, queued idle
characters, and queued break characters.
11.3.2.1 Send Break and Queued Idle
The SBK control bit in SCIxC2 is used to send break characters which were originally used to gain the
attention of old teletype receivers. Break characters are a full character time of logic 0 (10 bit times
including the start and stop bits). A longer break of 13 bit times can be enabled by setting BRK13 = 1.
Normally, a program would wait for TDRE to become set to indicate the last character of a message has
moved to the transmit shifter, then write 1 and then write 0 to the SBK bit. This action queues a break
character to be sent as soon as the shifter is available. If SBK is still 1 when the queued break moves into
the shifter (synchronized to the baud rate clock), an additional break character is queued. If the receiving
device is another Freescale Semiconductor SCI, the break characters will be received as 0s in all eight data
bits and a framing error (FE = 1) occurs.
When idle-line wakeup is used, a full character time of idle (logic 1) is needed between messages to wake
up any sleeping receivers. Normally, a program would wait for TDRE to become set to indicate the last
character of a message has moved to the transmit shifter, then write 0 and then write 1 to the TE bit. This
action queues an idle character to be sent as soon as the shifter is available. As long as the character in the
shifter does not finish while TE = 0, the SCI transmitter never actually releases control of the TxD pin. If
there is a possibility of the shifter finishing while TE = 0, set the general-purpose I/O controls so the pin
that is shared with TxD is an output driving a logic 1. This ensures that the TxD line will look like a normal
idle line even if the SCI loses control of the port pin between writing 0 and then 1 to TE.
The length of the break character is affected by the BRK13 and M bits as shown below.
Table 11-8. Break Character Length
BRK13
M
Break Character Length
0
0
1
1
0
1
0
1
10 bit times
11 bit times
13 bit times
14 bit times
11.3.3 Receiver Functional Description
In this section, the receiver block diagram (Figure 11-3) is used as a guide for the overall receiver
functional description. Next, the data sampling technique used to reconstruct receiver data is described in
more detail. Finally, two variations of the receiver wakeup function are explained.
The receiver is enabled by setting the RE bit in SCIxC2. Character frames consist of a start bit of logic 0,
eight (or nine) data bits (LSB first), and a stop bit of logic 1. For information about 9-bit data mode, refer
MC9S08AW60 Data Sheet, Rev 2
194
Freescale Semiconductor
Chapter 11 Serial Communications Interface (S08SCIV2)
to Section 11.3.5.1, “8- and 9-Bit Data Modes.” For the remainder of this discussion, we assume the SCI
is configured for normal 8-bit data mode.
After receiving the stop bit into the receive shifter, and provided the receive data register is not already full,
the data character is transferred to the receive data register and the receive data register full (RDRF) status
flag is set. If RDRF was already set indicating the receive data register (buffer) was already full, the overrun
(OR) status flag is set and the new data is lost. Because the SCI receiver is double-buffered, the program
has one full character time after RDRF is set before the data in the receive data buffer must be read to avoid
a receiver overrun.
When a program detects that the receive data register is full (RDRF = 1), it gets the data from the receive
data register by reading SCIxD. The RDRF flag is cleared automatically by a 2-step sequence which is
normally satisfied in the course of the user’s program that handles receive data. Refer to Section 11.3.4,
“Interrupts and Status Flags” for more details about flag clearing.
11.3.3.1 Data Sampling Technique
The SCI receiver uses a 16× baud rate clock for sampling. The receiver starts by taking logic level samples
at 16 times the baud rate to search for a falling edge on the RxD serial data input pin. A falling edge is
defined as a logic 0 sample after three consecutive logic 1 samples. The 16× baud rate clock is used to
divide the bit time into 16 segments labeled RT1 through RT16. When a falling edge is located, three more
samples are taken at RT3, RT5, and RT7 to make sure this was a real start bit and not merely noise. If at
least two of these three samples are 0, the receiver assumes it is synchronized to a receive character.
The receiver then samples each bit time, including the start and stop bits, at RT8, RT9, and RT10 to
determine the logic level for that bit. The logic level is interpreted to be that of the majority of the samples
taken during the bit time. In the case of the start bit, the bit is assumed to be 0 if at least two of the samples
at RT3, RT5, and RT7 are 0 even if one or all of the samples taken at RT8, RT9, and RT10 are 1s. If any
sample in any bit time (including the start and stop bits) in a character frame fails to agree with the logic
level for that bit, the noise flag (NF) will be set when the received character is transferred to the receive
data buffer.
The falling edge detection logic continuously looks for falling edges, and if an edge is detected, the sample
clock is resynchronized to bit times. This improves the reliability of the receiver in the presence of noise
or mismatched baud rates. It does not improve worst case analysis because some characters do not have
any extra falling edges anywhere in the character frame.
In the case of a framing error, provided the received character was not a break character, the sampling logic
that searches for a falling edge is filled with three logic 1 samples so that a new start bit can be detected
almost immediately.
In the case of a framing error, the receiver is inhibited from receiving any new characters until the framing
error flag is cleared. The receive shift register continues to function, but a complete character cannot
transfer to the receive data buffer if FE is still set.
11.3.3.2 Receiver Wakeup Operation
Receiver wakeup is a hardware mechanism that allows an SCI receiver to ignore the characters in a
message that is intended for a different SCI receiver. In such a system, all receivers evaluate the first
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
195
Chapter 11 Serial Communications Interface (S08SCIV2)
character(s) of each message, and as soon as they determine the message is intended for a different
receiver, they write logic 1 to the receiver wake up (RWU) control bit in SCIxC2. When RWU = 1, it
inhibits setting of the status flags associated with the receiver, thus eliminating the software overhead for
handling the unimportant message characters. At the end of a message, or at the beginning of the next
message, all receivers automatically force RWU to 0 so all receivers wake up in time to look at the first
character(s) of the next message.
11.3.3.2.1
Idle-Line Wakeup
When WAKE = 0, the receiver is configured for idle-line wakeup. In this mode, RWU is cleared
automatically when the receiver detects a full character time of the idle-line level. The M control bit selects
8-bit or 9-bit data mode that determines how many bit times of idle are needed to constitute a full character
time (10 or 11 bit times because of the start and stop bits).
When the RWU bit is set, the idle character that wakes a receiver does not set the receiver idle bit, IDLE,
or the receive data register full flag, RDRF. It therefore will not generate an interrupt when this idle
character occurs. The receiver will wake up and wait for the next data transmission which will set RDRF
and generate an interrupt if enabled.
The idle-line type (ILT) control bit selects one of two ways to detect an idle line. When ILT = 0, the idle
bit counter starts after the start bit so the stop bit and any logic 1s at the end of a character count toward
the full character time of idle. When ILT = 1, the idle bit counter does not start until after a stop bit time,
so the idle detection is not affected by the data in the last character of the previous message.
11.3.3.2.2
Address-Mark Wakeup
When WAKE = 1, the receiver is configured for address-mark wakeup. In this mode, RWU is cleared
automatically when the receiver detects a logic 1 in the most significant bit of a received character (eighth
bit in M = 0 mode and ninth bit in M = 1 mode).
Address-mark wakeup allows messages to contain idle characters but requires that the MSB be reserved
for use in address frames. The logic 1 MSB of an address frame clears the receivers RWU bit before the
stop bit is received and sets the RDRF flag.
11.3.4 Interrupts and Status Flags
The SCI system has three separate interrupt vectors to reduce the amount of software needed to isolate the
cause of the interrupt. One interrupt vector is associated with the transmitter for TDRE and TC events.
Another interrupt vector is associated with the receiver for RDRF and IDLE events, and a third vector is
used for OR, NF, FE, and PF error conditions. Each of these eight interrupt sources can be separately
masked by local interrupt enable masks. The flags can still be polled by software when the local masks are
cleared to disable generation of hardware interrupt requests.
The SCI transmitter has two status flags that optionally can generate hardware interrupt requests. Transmit
data register empty (TDRE) indicates when there is room in the transmit data buffer to write another
transmit character to SCIxD. If the transmit interrupt enable (TIE) bit is set, a hardware interrupt will be
requested whenever TDRE = 1. Transmit complete (TC) indicates that the transmitter is finished
transmitting all data, preamble, and break characters and is idle with TxD high. This flag is often used in
MC9S08AW60 Data Sheet, Rev 2
196
Freescale Semiconductor
Chapter 11 Serial Communications Interface (S08SCIV2)
systems with modems to determine when it is safe to turn off the modem. If the transmit complete interrupt
enable (TCIE) bit is set, a hardware interrupt will be requested whenever TC = 1. Instead of hardware
interrupts, software polling may be used to monitor the TDRE and TC status flags if the corresponding TIE
or TCIE local interrupt masks are 0s.
When a program detects that the receive data register is full (RDRF = 1), it gets the data from the receive
data register by reading SCIxD. The RDRF flag is cleared by reading SCIxS1 while RDRF = 1 and then
reading SCIxD. If the SCI is configured to operate in 9-bit mode, an additional read to the SCIxC3 register
is required to clear RDRF
When polling is used, this sequence is naturally satisfied in the normal course of the user program. If
hardware interrupts are used, SCIxS1 must be read in the interrupt service routine (ISR). Normally, this is
done in the ISR anyway to check for receive errors, so the sequence is automatically satisfied.
The IDLE status flag includes logic that prevents it from getting set repeatedly when the RxD line remains
idle for an extended period of time. IDLE is cleared by reading SCIxS1 while IDLE = 1 and then reading
SCIxD. After IDLE has been cleared, it cannot become set again until the receiver has received at least one
new character and has set RDRF.
If the associated error was detected in the received character that caused RDRF to be set, the error flags —
noise flag (NF), framing error (FE), and parity error flag (PF) — get set at the same time as RDRF. These
flags are not set in overrun cases.
If RDRF was already set when a new character is ready to be transferred from the receive shifter to the
receive data buffer, the overrun (OR) flag gets set instead and the data and any associated NF, FE, or PF
condition is lost.
11.3.5 Additional SCI Functions
The following sections describe additional SCI functions.
11.3.5.1 8- and 9-Bit Data Modes
The SCI system (transmitter and receiver) can be configured to operate in 9-bit data mode by setting the
M control bit in SCIxC1. In 9-bit mode, there is a ninth data bit to the left of the MSB of the SCI data
register. For the transmit data buffer, this bit is stored in T8 in SCIxC3. For the receiver, the ninth bit is
held in R8 in SCIxC3.
When transmitting 9-bit data, write to the T8 bit before writing to SCIxD for coherent writes to the transmit
data buffer. If the bit value to be transmitted as the ninth bit of a new character is the same as for the
previous character, it is not necessary to write to T8 again. When data is transferred from the transmit data
buffer to the transmit shifter, the value in T8 is copied at the same time data is transferred from SCIxD to
the shifter.
When receiving 9-bit data, clear the RDRF bit by reading both R8 and SCIxD. R8 and SCIxD can be read
in either order.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
197
Chapter 11 Serial Communications Interface (S08SCIV2)
9-bit data mode typically is used in conjunction with parity to allow eight bits of data plus the parity in the
ninth bit. Or it is used with address-mark wakeup so the ninth data bit can serve as the wakeup bit. In
custom protocols, the ninth bit can also serve as a software-controlled marker.
11.3.5.2 Stop Mode Operation
During all stop modes, clocks to the SCI module are halted.
In stop1 and stop2 modes, all SCI register data is lost and must be re-initialized upon recovery from these
two stop modes.
No SCI module registers are affected in stop3 mode.
Note, because the clocks are halted, the SCI module will resume operation upon exit from stop (only in
stop3 mode). Software should ensure stop mode is not entered while there is a character being transmitted
out of or received into the SCI module.
11.3.5.3 Loop Mode
When LOOPS = 1, the RSRC bit in the same register chooses between loop mode (RSRC = 0) or
single-wire mode (RSRC = 1). Loop mode is sometimes used to check software, independent of
connections in the external system, to help isolate system problems. In this mode, the transmitter output is
internally connected to the receiver input and the RxD pin is not used by the SCI, so it reverts to a
general-purpose port I/O pin.
11.3.5.4 Single-Wire Mode
When LOOPS = 1, the RSRC bit in the same register chooses between loop mode (RSRC = 0) or
single-wire mode (RSRC = 1). Single-wire mode is used to implement a half-duplex serial connection.
The receiver is internally connected to the transmitter output and to the TxD pin. The RxD pin is not used
and reverts to a general-purpose port I/O pin.
In single-wire mode, the TXDIR bit in SCIxC3 controls the direction of serial data on the TxD pin. When
TXDIR = 0, the TxD pin is an input to the SCI receiver and the transmitter is temporarily disconnected
from the TxD pin so an external device can send serial data to the receiver. When TXDIR = 1, the TxD pin
is an output driven by the transmitter.
MC9S08AW60 Data Sheet, Rev 2
198
Freescale Semiconductor
Chapter 12
Serial Peripheral Interface (S08SPIV3)
The MC9S08AW60 Series has one serial peripheral interface (SPI) module. The four pins associated with
SPI functionality are shared with port E pins 4–7. See Appendix A, “Electrical Characteristics and Timing
Specifications,” for SPI electrical parametric information.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
199
SPIChapter 12 Serial Peripheral Interface (S08SPIV3)
HCS08 CORE
DEBUG
MODULE (DBG)
8
PTA7– PTA0
BKGD/MS
BDC
CPU
8
PTB7/AD1P7–
PTB0/AD1P0
HCS08 SYSTEM CONTROL
RESET
IRQ
PTC6
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
RxD2
TxD2
PTC5/RxD2
PTC4
PTC3/TxD2
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI2)
PTC2/MCLK
PTC1/SDA1
SDA1
SCL1
RTI
COP
LVD
IIC MODULE (IIC1)
PTC0/SCL1
IRQ
AD1P7–AD1P0
8
V
DDAD
8
10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC1)
AD1P15–AD1P8
V
SSAD
V
REFL
PTD7/AD1P15/KBI1P7
PTD6/AD1P14/TPM1CLK
PTD5/AD1P13
PTD4/AD1P12/TPM2CLK
PTD3/AD1P11/KBI1P6
PTD2/AD1P10/KBI1P5
PTD1/AD1P9
V
REFH
USER FLASH
(AW60 = 63,280 BYTES)
(AW48 = 49,152 BYTES)
(AW32 = 32,768 BYTES)
(AW16 = 16,384 BYTES)
PTD0/AD1P8
SPSCK1
PTE7/SPSCK1
PTE6/MOSI1
MOSI1
SERIAL PERIPHERAL
INTERFACE MODULE (SPI1)
USER RAM
MISO1
SS1
PTE5/MISO1
PTE4/SS1
AW60/48/32 = 2048 BYTES
AW16 = 1024 BYTES
TPM1CLK
PTE3/TPM1CH1
PTE2/TPM1CH0
6-CHANNEL TIMER/PWM
MODULE (TPM1)
TPM1CH5–
TPM1CH0
INTERNAL CLOCK
GENERATOR (ICG)
6
RxD1
TxD1
PTE1/RxD1
PTE0/TxD1
PTF7
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI1)
LOW-POWER OSCILLATOR
PTF6
PTF5/TPM2CH1
PTF4/TPM2CH0
TPM2CLK
V
DD
VOLTAGE
REGULATOR
2-CHANNEL TIMER/PWM
MODULE (TPM2)
TPM2CH1–TPM2CH0
V
SS
2
PTF3/TPM1CH5
KBI1P7–KBI1P5
3
PTF2/TPM1CH4
PTF1/TPM1CH3
PTF0/TPM1CH2
8-BIT KEYBOARD
INTERRUPT MODULE (KBI1)
KBI1P4–KBI1P0
5
EXTAL
XTAL
PTG6/EXTAL
PTG5/XTAL
NOTES:
PTG4/KBI1P4
PTG3/KBI1P3
PTG2/KBI1P2
PTG1/KBI1P1
PTG0/KBI1P0
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software configurable pullup/pulldown device if IRQ is enabled
(IRQPE = 1). Pulldown is enabled if rising edge detect is selected (IRQEDG = 1)
3. IRQ does not have a clamp diode to VDD. IRQ should not be driven above VDD
4. Pin contains integrated pullup device.
.
5. Pins PTD7, PTD3, PTD2, and PTG4 contain both pullup and pulldown devices.
Pulldown enabled when KBI is enabled (KBIPEn = 1) and rising edge is selected
(KBEDGn = 1).
Figure 12-1. Block Diagram Highlighting the SPI Module
MC9S08AW60 Data Sheet, Rev 2
200
Freescale Semiconductor
Chapter 12 Serial Peripheral Interface (S08SPIV3)
12.0.1 Features
Features of the SPI module include:
•
•
•
•
•
•
•
Master or slave mode operation
Full-duplex or single-wire bidirectional option
Programmable transmit bit rate
Double-buffered transmit and receive
Serial clock phase and polarity options
Slave select output
Selectable MSB-first or LSB-first shifting
12.0.2 Block Diagrams
This section includes block diagrams showing SPI system connections, the internal organization of the SPI
module, and the SPI clock dividers that control the master mode bit rate.
12.0.2.1 SPI System Block Diagram
Figure 12-2 shows the SPI modules of two MCUs connected in a master-slave arrangement. The master
device initiates all SPI data transfers. During a transfer, the master shifts data out (on the MOSI pin) to the
slave while simultaneously shifting data in (on the MISO pin) from the slave. The transfer effectively
exchanges the data that was in the SPI shift registers of the two SPI systems. The SPSCK signal is a clock
output from the master and an input to the slave. The slave device must be selected by a low level on the
slave select input (SS pin). In this system, the master device has configured its SS pin as an optional slave
select output.
SLAVE
MASTER
MOSI
MISO
MOSI
MISO
SPI SHIFTER
SPI SHIFTER
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
SPSCK
SS
SPSCK
SS
CLOCK
GENERATOR
Figure 12-2. SPI System Connections
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
201
Chapter 12 Serial Peripheral Interface (S08SPIV3)
The most common uses of the SPI system include connecting simple shift registers for adding input or
output ports or connecting small peripheral devices such as serial A/D or D/A converters. Although
Figure 12-2 shows a system where data is exchanged between two MCUs, many practical systems involve
simpler connections where data is unidirectionally transferred from the master MCU to a slave or from a
slave to the master MCU.
12.0.2.2 SPI Module Block Diagram
Figure 12-3 is a block diagram of the SPI module. The central element of the SPI is the SPI shift register.
Data is written to the double-buffered transmitter (write to SPI1D) and gets transferred to the SPI shift
register at the start of a data transfer. After shifting in a byte of data, the data is transferred into the
double-buffered receiver where it can be read (read from SPI1D). Pin multiplexing logic controls
connections between MCU pins and the SPI module.
When the SPI is configured as a master, the clock output is routed to the SPSCK pin, the shifter output is
routed to MOSI, and the shifter input is routed from the MISO pin.
When the SPI is configured as a slave, the SPSCK pin is routed to the clock input of the SPI, the shifter
output is routed to MISO, and the shifter input is routed from the MOSI pin.
In the external SPI system, simply connect all SPSCK pins to each other, all MISO pins together, and all
MOSI pins together. Peripheral devices often use slightly different names for these pins.
MC9S08AW60 Data Sheet, Rev 2
202
Freescale Semiconductor
Chapter 12 Serial Peripheral Interface (S08SPIV3)
PIN CONTROL
M
MOSI
SPE
S
(MOMI)
Tx BUFFER (WRITE SPI1D)
ENABLE
M
S
MISO
SPI SYSTEM
(SISO)
SHIFT
OUT
SHIFT
IN
SPI SHIFT REGISTER
SPC0
Rx BUFFER (READ SPI1D)
BIDIROE
SHIFT
SHIFT
Rx BUFFER
FULL
Tx BUFFER
EMPTY
LSBFE
DIRECTION
CLOCK
MASTER CLOCK
SLAVE CLOCK
M
S
BUS RATE
CLOCK
CLOCK
LOGIC
SPIBR
SPSCK
CLOCK GENERATOR
MASTER/SLAVE
MODE SELECT
MASTER/
SLAVE
MSTR
MODFEN
SSOE
MODE FAULT
DETECTION
SS
SPTEF
SPTIE
SPRF
SPI
INTERRUPT
REQUEST
MODF
SPIE
Figure 12-3. SPI Module Block Diagram
12.0.3 SPI Baud Rate Generation
As shown in Figure 12-4, the clock source for the SPI baud rate generator is the bus clock. The three
prescale bits (SPPR2:SPPR1:SPPR0) choose a prescale divisor of 1, 2, 3, 4, 5, 6, 7, or 8. The three rate
select bits (SPR2:SPR1:SPR0) divide the output of the prescaler stage by 2, 4, 8, 16, 32, 64, 128, or 256
to get the internal SPI master mode bit-rate clock.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
203
Chapter 12 Serial Peripheral Interface (S08SPIV3)
PRESCALER
CLOCK RATE DIVIDER
MASTER
SPI
BIT RATE
DIVIDE BY
DIVIDE BY
BUS CLOCK
1, 2, 3, 4, 5, 6, 7, or 8
2, 4, 8, 16, 32, 64, 128, or 256
SPPR2:SPPR1:SPPR0
SPR2:SPR1:SPR0
Figure 12-4. SPI Baud Rate Generation
12.1 External Signal Description
The SPI optionally shares four port pins. The function of these pins depends on the settings of SPI control
bits. When the SPI is disabled (SPE = 0), these four pins revert to being general-purpose port I/O pins that
are not controlled by the SPI.
12.1.1 SPSCK — SPI Serial Clock
When the SPI is enabled as a slave, this pin is the serial clock input. When the SPI is enabled as a master,
this pin is the serial clock output.
12.1.2 MOSI — Master Data Out, Slave Data In
When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not bidirectional mode), this
pin is the serial data output. When the SPI is enabled as a slave and SPC0 = 0, this pin is the serial data
input. If SPC0 = 1 to select single-wire bidirectional mode, and master mode is selected, this pin becomes
the bidirectional data I/O pin (MOMI). Also, the bidirectional mode output enable bit determines whether
the pin acts as an input (BIDIROE = 0) or an output (BIDIROE = 1). If SPC0 = 1 and slave mode is
selected, this pin is not used by the SPI and reverts to being a general-purpose port I/O pin.
12.1.3 MISO — Master Data In, Slave Data Out
When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not bidirectional mode), this
pin is the serial data input. When the SPI is enabled as a slave and SPC0 = 0, this pin is the serial data
output. If SPC0 = 1 to select single-wire bidirectional mode, and slave mode is selected, this pin becomes
the bidirectional data I/O pin (SISO) and the bidirectional mode output enable bit determines whether the
pin acts as an input (BIDIROE = 0) or an output (BIDIROE = 1). If SPC0 = 1 and master mode is selected,
this pin is not used by the SPI and reverts to being a general-purpose port I/O pin.
12.1.4 SS — Slave Select
When the SPI is enabled as a slave, this pin is the low-true slave select input. When the SPI is enabled as
a master and mode fault enable is off (MODFEN = 0), this pin is not used by the SPI and reverts to being
a general-purpose port I/O pin. When the SPI is enabled as a master and MODFEN = 1, the slave select
output enable bit determines whether this pin acts as the mode fault input (SSOE = 0) or as the slave select
output (SSOE = 1).
MC9S08AW60 Data Sheet, Rev 2
204
Freescale Semiconductor
Chapter 12 Serial Peripheral Interface (S08SPIV3)
12.2 Modes of Operation
12.2.1 SPI in Stop Modes
The SPI is disabled in all stop modes, regardless of the settings before executing the STOP instruction.
During either stop1 or stop2 mode, the SPI module will be fully powered down. Upon wake-up from stop1
or stop2 mode, the SPI module will be in the reset state. During stop3 mode, clocks to the SPI module are
halted. No registers are affected. If stop3 is exited with a reset, the SPI will be put into its reset state. If
stop3 is exited with an interrupt, the SPI continues from the state it was in when stop3 was entered.
12.3 Register Definition
The SPI has five 8-bit registers to select SPI options, control baud rate, report SPI status, and for
transmit/receive data.
Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address
assignments for all SPI registers. This section refers to registers and control bits only by their names, and
a Freescale-provided equate or header file is used to translate these names into the appropriate absolute
addresses.
12.3.1 SPI Control Register 1 (SPI1C1)
This read/write register includes the SPI enable control, interrupt enables, and configuration options.
7
6
5
4
3
2
1
0
R
W
SPIE
SPE
SPTIE
MSTR
CPOL
CPHA
SSOE
LSBFE
Reset
0
0
0
0
0
1
0
0
Figure 12-5. SPI Control Register 1 (SPI1C1)
Table 12-1. SPI1C1 Field Descriptions
Description
Field
7
SPI Interrupt Enable (for SPRF and MODF) — This is the interrupt enable for SPI receive buffer full (SPRF)
and mode fault (MODF) events.
SPIE
0 Interrupts from SPRF and MODF inhibited (use polling)
1 When SPRF or MODF is 1, request a hardware interrupt
6
SPI System Enable — Disabling the SPI halts any transfer that is in progress, clears data buffers, and initializes
SPE
internal state machines. SPRF is cleared and SPTEF is set to indicate the SPI transmit data buffer is empty.
0 SPI system inactive
1 SPI system enabled
5
SPI Transmit Interrupt Enable — This is the interrupt enable bit for SPI transmit buffer empty (SPTEF).
0 Interrupts from SPTEF inhibited (use polling)
SPTIE
1 When SPTEF is 1, hardware interrupt requested
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
205
Chapter 12 Serial Peripheral Interface (S08SPIV3)
Table 12-1. SPI1C1 Field Descriptions (continued)
Field
Description
4
Master/Slave Mode Select
MSTR
0 SPI module configured as a slave SPI device
1 SPI module configured as a master SPI device
3
Clock Polarity — This bit effectively places an inverter in series with the clock signal from a master SPI or to a
slave SPI device. Refer to Section 12.4.1, “SPI Clock Formats” for more details.
0 Active-high SPI clock (idles low)
CPOL
1 Active-low SPI clock (idles high)
2
Clock Phase — This bit selects one of two clock formats for different kinds of synchronous serial peripheral
devices. Refer to Section 12.4.1, “SPI Clock Formats” for more details.
CPHA
0 First edge on SPSCK occurs at the middle of the first cycle of an 8-cycle data transfer
1 First edge on SPSCK occurs at the start of the first cycle of an 8-cycle data transfer
1
Slave Select Output Enable — This bit is used in combination with the mode fault enable (MODFEN) bit in
SSOE
SPCR2 and the master/slave (MSTR) control bit to determine the function of the SS pin as shown in Table 12-2.
0
LSB First (Shifter Direction)
LSBFE
0 SPI serial data transfers start with most significant bit
1 SPI serial data transfers start with least significant bit
Table 12-2. SS Pin Function
MODFEN
SSOE
Master Mode
Slave Mode
Slave select input
0
0
1
1
0
1
0
1
General-purpose I/O (not SPI)
General-purpose I/O (not SPI)
SS input for mode fault
Slave select input
Slave select input
Slave select input
Automatic SS output
NOTE
Ensure that the SPI should not be disabled (SPE=0) at the same time as a bit change to the CPHA bit. These
changes should be performed as separate operations or unexpected behavior may occur.
12.3.2 SPI Control Register 2 (SPI1C2)
This read/write register is used to control optional features of the SPI system. Bits 7, 6, 5, and 2 are not
implemented and always read 0.
7
6
5
4
3
2
1
0
R
W
0
0
0
0
MODFEN
BIDIROE
SPISWAI
SPC0
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 12-6. SPI Control Register 2 (SPI1C2)
MC9S08AW60 Data Sheet, Rev 2
206
Freescale Semiconductor
Chapter 12 Serial Peripheral Interface (S08SPIV3)
Table 12-3. SPI1C2 Register Field Descriptions
Field
Description
4
Master Mode-Fault Function Enable — When the SPI is configured for slave mode, this bit has no meaning or
MODFEN effect. (The SS pin is the slave select input.) In master mode, this bit determines how the SS pin is used (refer
to Table 12-2 for more details).
0 Mode fault function disabled, master SS pin reverts to general-purpose I/O not controlled by SPI
1 Mode fault function enabled, master SS pin acts as the mode fault input or the slave select output
3
Bidirectional Mode Output Enable — When bidirectional mode is enabled by SPI pin control 0 (SPC0) = 1,
BIDIROE BIDIROE determines whether the SPI data output driver is enabled to the single bidirectional SPI I/O pin.
Depending on whether the SPI is configured as a master or a slave, it uses either the MOSI (MOMI) or MISO
(SISO) pin, respectively, as the single SPI data I/O pin. When SPC0 = 0, BIDIROE has no meaning or effect.
0 Output driver disabled so SPI data I/O pin acts as an input
1 SPI I/O pin enabled as an output
1
SPI Stop in Wait Mode
SPISWAI 0 SPI clocks continue to operate in wait mode
1 SPI clocks stop when the MCU enters wait mode
0
SPI Pin Control 0 — The SPC0 bit chooses single-wire bidirectional mode. If MSTR = 0 (slave mode), the SPI
uses the MISO (SISO) pin for bidirectional SPI data transfers. If MSTR = 1 (master mode), the SPI uses the
MOSI (MOMI) pin for bidirectional SPI data transfers. When SPC0 = 1, BIDIROE is used to enable or disable the
output driver for the single bidirectional SPI I/O pin.
SPC0
0 SPI uses separate pins for data input and data output
1 SPI configured for single-wire bidirectional operation
12.3.3 SPI Baud Rate Register (SPI1BR)
This register is used to set the prescaler and bit rate divisor for an SPI master. This register may be read or
written at any time.
7
6
5
4
3
2
1
0
R
W
0
0
SPPR2
SPPR1
SPPR0
SPR2
SPR1
SPR0
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 12-7. SPI Baud Rate Register (SPI1BR)
Table 12-4. SPI1BR Register Field Descriptions
Description
Field
6:4
SPI Baud Rate Prescale Divisor — This 3-bit field selects one of eight divisors for the SPI baud rate prescaler
SPPR[2:0] as shown in Table 12-5. The input to this prescaler is the bus rate clock (BUSCLK). The output of this prescaler
drives the input of the SPI baud rate divider (see Figure 12-4).
2:0
SPR[2:0]
SPI Baud Rate Divisor — This 3-bit field selects one of eight divisors for the SPI baud rate divider as shown in
Table 12-6. The input to this divider comes from the SPI baud rate prescaler (see Figure 12-4). The output of this
divider is the SPI bit rate clock for master mode.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
207
Chapter 12 Serial Peripheral Interface (S08SPIV3)
Table 12-5. SPI Baud Rate Prescaler Divisor
SPPR2:SPPR1:SPPR0
Prescaler Divisor
0:0:0
0:0:1
0:1:0
0:1:1
1:0:0
1:0:1
1:1:0
1:1:1
1
2
3
4
5
6
7
8
Table 12-6. SPI Baud Rate Divisor
SPR2:SPR1:SPR0
0:0:0
Rate Divisor
2
0:0:1
0:1:0
0:1:1
1:0:0
1:0:1
1:1:0
1:1:1
4
8
16
32
64
128
256
12.3.4 SPI Status Register (SPI1S)
This register has three read-only status bits. Bits 6, 3, 2, 1, and 0 are not implemented and always read 0.
Writes have no meaning or effect.
7
6
5
4
3
2
1
0
R
W
SPRF
0
SPTEF
MODF
0
0
0
0
Reset
0
0
1
0
0
0
0
0
= Unimplemented or Reserved
Figure 12-8. SPI Status Register (SPI1S)
MC9S08AW60 Data Sheet, Rev 2
208
Freescale Semiconductor
Chapter 12 Serial Peripheral Interface (S08SPIV3)
Table 12-7. SPI1S Register Field Descriptions
Field
Description
7
SPI Read Buffer Full Flag — SPRF is set at the completion of an SPI transfer to indicate that received data may
be read from the SPI data register (SPI1D). SPRF is cleared by reading SPRF while it is set, then reading the
SPI data register.
SPRF
0 No data available in the receive data buffer
1 Data available in the receive data buffer
5
SPI Transmit Buffer Empty Flag — This bit is set when there is room in the transmit data buffer. It is cleared by
reading SPI1S with SPTEF set, followed by writing a data value to the transmit buffer at SPI1D. SPI1S must be
read with SPTEF = 1 before writing data to SPI1D or the SPI1D write will be ignored. SPTEF generates an
SPTEF CPU interrupt request if the SPTIE bit in the SPI1C1 is also set. SPTEF is automatically set when a data
byte transfers from the transmit buffer into the transmit shift register. For an idle SPI (no data in the transmit buffer
or the shift register and no transfer in progress), data written to SPI1D is transferred to the shifter almost
immediately so SPTEF is set within two bus cycles allowing a second 8-bit data value to be queued into the
transmit buffer. After completion of the transfer of the value in the shift register, the queued value from the
transmit buffer will automatically move to the shifter and SPTEF will be set to indicate there is room for new data
in the transmit buffer. If no new data is waiting in the transmit buffer, SPTEF simply remains set and no data
moves from the buffer to the shifter.
SPTEF
0 SPI transmit buffer not empty
1 SPI transmit buffer empty
4
Master Mode Fault Flag — MODF is set if the SPI is configured as a master and the slave select input goes
low, indicating some other SPI device is also configured as a master. The SS pin acts as a mode fault error input
only when MSTR = 1, MODFEN = 1, and SSOE = 0; otherwise, MODF will never be set. MODF is cleared by
reading MODF while it is 1, then writing to SPI control register 1 (SPI1C1).
0 No mode fault error
MODF
1 Mode fault error detected
12.3.5 SPI Data Register (SPI1D)
7
6
5
4
3
2
1
0
R
W
Bit 7
6
5
4
3
2
1
Bit 0
Reset
0
0
0
0
0
0
0
0
Figure 12-9. SPI Data Register (SPI1D)
Reads of this register return the data read from the receive data buffer. Writes to this register write data to
the transmit data buffer. When the SPI is configured as a master, writing data to the transmit data buffer
initiates an SPI transfer.
Data should not be written to the transmit data buffer unless the SPI transmit buffer empty flag (SPTEF)
is set, indicating there is room in the transmit buffer to queue a new transmit byte.
Data may be read from SPI1D any time after SPRF is set and before another transfer is finished. Failure
to read the data out of the receive data buffer before a new transfer ends causes a receive overrun condition
and the data from the new transfer is lost.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
209
Chapter 12 Serial Peripheral Interface (S08SPIV3)
12.4 Functional Description
An SPI transfer is initiated by checking for the SPI transmit buffer empty flag (SPTEF = 1) and then
writing a byte of data to the SPI data register (SPI1D) in the master SPI device. When the SPI shift register
is available, this byte of data is moved from the transmit data buffer to the shifter, SPTEF is set to indicate
there is room in the buffer to queue another transmit character if desired, and the SPI serial transfer starts.
During the SPI transfer, data is sampled (read) on the MISO pin at one SPSCK edge and shifted, changing
the bit value on the MOSI pin, one-half SPSCK cycle later. After eight SPSCK cycles, the data that was in
the shift register of the master has been shifted out the MOSI pin to the slave while eight bits of data were
shifted in the MISO pin into the master’s shift register. At the end of this transfer, the received data byte is
moved from the shifter into the receive data buffer and SPRF is set to indicate the data can be read by
reading SPI1D. If another byte of data is waiting in the transmit buffer at the end of a transfer, it is moved
into the shifter, SPTEF is set, and a new transfer is started.
Normally, SPI data is transferred most significant bit (MSB) first. If the least significant bit first enable
(LSBFE) bit is set, SPI data is shifted LSB first.
When the SPI is configured as a slave, its SS pin must be driven low before a transfer starts and SS must
stay low throughout the transfer. If a clock format where CPHA = 0 is selected, SS must be driven to a
logic 1 between successive transfers. If CPHA = 1, SS may remain low between successive transfers. See
Section 12.4.1, “SPI Clock Formats” for more details.
Because the transmitter and receiver are double buffered, a second byte, in addition to the byte currently
being shifted out, can be queued into the transmit data buffer, and a previously received character can be
in the receive data buffer while a new character is being shifted in. The SPTEF flag indicates when the
transmit buffer has room for a new character. The SPRF flag indicates when a received character is
available in the receive data buffer. The received character must be read out of the receive buffer (read
SPI1D) before the next transfer is finished or a receive overrun error results.
In the case of a receive overrun, the new data is lost because the receive buffer still held the previous
character and was not ready to accept the new data. There is no indication for such an overrun condition
so the application system designer must ensure that previous data has been read from the receive buffer
before a new transfer is initiated.
12.4.1 SPI Clock Formats
To accommodate a wide variety of synchronous serial peripherals from different manufacturers, the SPI
system has a clock polarity (CPOL) bit and a clock phase (CPHA) control bit to select one of four clock
formats for data transfers. CPOL selectively inserts an inverter in series with the clock. CPHA chooses
between two different clock phase relationships between the clock and data.
Figure 12-10 shows the clock formats when CPHA = 1. At the top of the figure, the eight bit times are
shown for reference with bit 1 starting at the first SPSCK edge and bit 8 ending one-half SPSCK cycle after
the sixteenth SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending
on the setting in LSBFE. Both variations of SPSCK polarity are shown, but only one of these waveforms
applies for a specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies to the
MOSI input of a slave or the MISO input of a master. The MOSI waveform applies to the MOSI output
MC9S08AW60 Data Sheet, Rev 2
210
Freescale Semiconductor
Chapter 12 Serial Peripheral Interface (S08SPIV3)
pin from a master and the MISO waveform applies to the MISO output from a slave. The SS OUT
waveform applies to the slave select output from a master (provided MODFEN and SSOE = 1). The master
SS output goes to active low one-half SPSCK cycle before the start of the transfer and goes back high at
the end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select input of a
slave.
BIT TIME #
(REFERENCE)
1
2
...
6
7
8
SPSCK
(CPOL = 0)
SPSCK
(CPOL = 1)
SAMPLE IN
(MISO OR MOSI)
MOSI
(MASTER OUT)
MSB FIRST
LSB FIRST
BIT 7
BIT 0
BIT 6
BIT 1
...
...
BIT 2
BIT 5
BIT 1
BIT 6
BIT 0
BIT 7
MISO
(SLAVE OUT)
SS OUT
(MASTER)
SS IN
(SLAVE)
Figure 12-10. SPI Clock Formats (CPHA = 1)
When CPHA = 1, the slave begins to drive its MISO output when SS goes to active low, but the data is not
defined until the first SPSCK edge. The first SPSCK edge shifts the first bit of data from the shifter onto
the MOSI output of the master and the MISO output of the slave. The next SPSCK edge causes both the
master and the slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the
third SPSCK edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled,
and shifts the second data bit value out the other end of the shifter to the MOSI and MISO outputs of the
master and slave, respectively. When CHPA = 1, the slave’s SS input is not required to go to its inactive
high level between transfers.
Figure 12-11 shows the clock formats when CPHA = 0. At the top of the figure, the eight bit times are
shown for reference with bit 1 starting as the slave is selected (SS IN goes low), and bit 8 ends at the last
SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending on the setting
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
211
Chapter 12 Serial Peripheral Interface (S08SPIV3)
in LSBFE. Both variations of SPSCK polarity are shown, but only one of these waveforms applies for a
specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies to the MOSI input
of a slave or the MISO input of a master. The MOSI waveform applies to the MOSI output pin from a
master and the MISO waveform applies to the MISO output from a slave. The SS OUT waveform applies
to the slave select output from a master (provided MODFEN and SSOE = 1). The master SS output goes
to active low at the start of the first bit time of the transfer and goes back high one-half SPSCK cycle after
the end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select input of a
slave.
BIT TIME #
(REFERENCE)
1
2
...
6
7
8
SPSCK
(CPOL = 0)
SPSCK
(CPOL = 1)
SAMPLE IN
(MISO OR MOSI)
MOSI
(MASTER OUT)
MSB FIRST
LSB FIRST
BIT 7
BIT 0
BIT 6
BIT 1
...
...
BIT 2
BIT 5
BIT 1
BIT 6
BIT 0
BIT 7
MISO
(SLAVE OUT)
SS OUT
(MASTER)
SS IN
(SLAVE)
Figure 12-11. SPI Clock Formats (CPHA = 0)
When CPHA = 0, the slave begins to drive its MISO output with the first data bit value (MSB or LSB
depending on LSBFE) when SS goes to active low. The first SPSCK edge causes both the master and the
slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the second SPSCK
edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled and shifts the
second data bit value out the other end of the shifter to the MOSI and MISO outputs of the master and
slave, respectively. When CPHA = 0, the slave’s SS input must go to its inactive high level between
transfers.
MC9S08AW60 Data Sheet, Rev 2
212
Freescale Semiconductor
Chapter 12 Serial Peripheral Interface (S08SPIV3)
12.4.2 SPI Interrupts
There are three flag bits, two interrupt mask bits, and one interrupt vector associated with the SPI system.
The SPI interrupt enable mask (SPIE) enables interrupts from the SPI receiver full flag (SPRF) and mode
fault flag (MODF). The SPI transmit interrupt enable mask (SPTIE) enables interrupts from the SPI
transmit buffer empty flag (SPTEF). When one of the flag bits is set, and the associated interrupt mask bit
is set, a hardware interrupt request is sent to the CPU. If the interrupt mask bits are cleared, software can
poll the associated flag bits instead of using interrupts. The SPI interrupt service routine (ISR) should
check the flag bits to determine what event caused the interrupt. The service routine should also clear the
flag bit(s) before returning from the ISR (usually near the beginning of the ISR).
12.4.3 Mode Fault Detection
A mode fault occurs and the mode fault flag (MODF) becomes set when a master SPI device detects an
error on the SS pin (provided the SS pin is configured as the mode fault input signal). The SS pin is
configured to be the mode fault input signal when MSTR = 1, mode fault enable is set (MODFEN = 1),
and slave select output enable is clear (SSOE = 0).
The mode fault detection feature can be used in a system where more than one SPI device might become
a master at the same time. The error is detected when a master’s SS pin is low, indicating that some other
SPI device is trying to address this master as if it were a slave. This could indicate a harmful output driver
conflict, so the mode fault logic is designed to disable all SPI output drivers when such an error is detected.
When a mode fault is detected, MODF is set and MSTR is cleared to change the SPI configuration back
to slave mode. The output drivers on the SPSCK, MOSI, and MISO (if not bidirectional mode) are
disabled.
MODF is cleared by reading it while it is set, then writing to the SPI control register 1 (SPI1C1). User
software should verify the error condition has been corrected before changing the SPI back to master
mode.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
213
Chapter 12 Serial Peripheral Interface (S08SPIV3)
MC9S08AW60 Data Sheet, Rev 2
214
Freescale Semiconductor
Chapter 13
Inter-Integrated Circuit (S08IICV1)
13.1 Introduction
The MC9S08AW60 Series of microcontrollers has an inter-integrated circuit (IIC) module for
communication with other integrated circuits. The two pins associated with this module, SCL and SDA,
are open-drain outputs and are shared with port C pins 0 and 1, respectively.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
215
IICChapter 13 Inter-Integrated Circuit (S08IICV1)
HCS08 CORE
DEBUG
MODULE (DBG)
8
PTA7– PTA0
BKGD/MS
BDC
CPU
8
PTB7/AD1P7–
PTB0/AD1P0
HCS08 SYSTEM CONTROL
RESET
IRQ
PTC6
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
RxD2
TxD2
PTC5/RxD2
PTC4
PTC3/TxD2
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI2)
PTC2/MCLK
PTC1/SDA1
SDA1
SCL1
RTI
COP
LVD
IIC MODULE (IIC1)
PTC0/SCL1
IRQ
AD1P7–AD1P0
8
V
DDAD
8
10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC1)
AD1P15–AD1P8
V
SSAD
V
REFL
PTD7/AD1P15/KBI1P7
PTD6/AD1P14/TPM1CLK
PTD5/AD1P13
PTD4/AD1P12/TPM2CLK
PTD3/AD1P11/KBI1P6
PTD2/AD1P10/KBI1P5
PTD1/AD1P9
V
REFH
USER FLASH
(AW60 = 63,280 BYTES)
(AW48 = 49,152 BYTES)
(AW32 = 32,768 BYTES)
(AW16 = 16,384 BYTES)
PTD0/AD1P8
SPSCK1
PTE7/SPSCK1
PTE6/MOSI1
MOSI1
SERIAL PERIPHERAL
USER RAM
MISO1
SS1
INTERFACE MODULE (SPI1)
PTE5/MISO1
PTE4/SS1
AW60/48/32 = 2048 BYTES
AW16 = 1024 BYTES
TPM1CLK
PTE3/TPM1CH1
PTE2/TPM1CH0
6-CHANNEL TIMER/PWM
MODULE (TPM1)
TPM1CH5–
TPM1CH0
INTERNAL CLOCK
GENERATOR (ICG)
6
RxD1
TxD1
PTE1/RxD1
PTE0/TxD1
PTF7
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI1)
LOW-POWER OSCILLATOR
PTF6
PTF5/TPM2CH1
PTF4/TPM2CH0
TPM2CLK
V
DD
VOLTAGE
REGULATOR
2-CHANNEL TIMER/PWM
MODULE (TPM2)
TPM2CH1–TPM2CH0
V
SS
2
PTF3/TPM1CH5
KBI1P7–KBI1P5
3
PTF2/TPM1CH4
PTF1/TPM1CH3
PTF0/TPM1CH2
8-BIT KEYBOARD
INTERRUPT MODULE (KBI1)
KBI1P4–KBI1P0
5
EXTAL
XTAL
PTG6/EXTAL
PTG5/XTAL
NOTES:
PTG4/KBI1P4
PTG3/KBI1P3
PTG2/KBI1P2
PTG1/KBI1P1
PTG0/KBI1P0
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software configurable pullup/pulldown device if IRQ is enabled
(IRQPE = 1). Pulldown is enabled if rising edge detect is selected (IRQEDG = 1)
3. IRQ does not have a clamp diode to VDD. IRQ should not be driven above VDD
4. Pin contains integrated pullup device.
.
5. Pins PTD7, PTD3, PTD2, and PTG4 contain both pullup and pulldown devices.
Pulldown enabled when KBI is enabled (KBIPEn = 1) and rising edge is selected
(KBEDGn = 1).
Figure 13-1. Block Diagram Highlighting the IIC Module
MC9S08AW60 Data Sheet, Rev 2
216
Freescale Semiconductor
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.1.1 Features
The IIC includes these distinctive features:
•
•
•
•
•
•
•
•
•
•
•
Compatible with IIC bus standard
Multi-master operation
Software programmable for one of 64 different serial clock frequencies
Software selectable acknowledge bit
Interrupt driven byte-by-byte data transfer
Arbitration lost interrupt with automatic mode switching from master to slave
Calling address identification interrupt
START and STOP signal generation/detection
Repeated START signal generation
Acknowledge bit generation/detection
Bus busy detection
13.1.2 Modes of Operation
The IIC functions the same in normal and monitor modes. A brief description of the IIC in the various
MCU modes is given here.
•
•
•
Run mode — This is the basic mode of operation. To conserve power in this mode, disable the
module.
Wait mode — The module will continue to operate while the MCU is in wait mode and can provide
a wake-up interrupt.
Stop mode — The IIC is inactive in stop3 mode for reduced power consumption. The STOP
instruction does not affect IIC register states. Stop2 will reset the register contents.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
217
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.1.3 Block Diagram
Figure 13-2 is a block diagram of the IIC.
ADDRESS
DATA BUS
DATA_MUX
INTERRUPT
ADDR_DECODE
CTRL_REG
FREQ_REG
ADDR_REG
STATUS_REG
DATA_REG
INPUT
SYNC
IN/OUT
DATA
START
STOP
SHIFT
ARBITRATION
CONTROL
REGISTER
CLOCK
ADDRESS
COMPARE
CONTROL
SDA
SCL
Figure 13-2. IIC Functional Block Diagram
13.2 External Signal Description
This section describes each user-accessible pin signal.
13.2.1 SCL — Serial Clock Line
The bidirectional SCL is the serial clock line of the IIC system.
13.2.2 SDA — Serial Data Line
The bidirectional SDA is the serial data line of the IIC system.
13.3 Register Definition
This section consists of the IIC register descriptions in address order.
MC9S08AW60 Data Sheet, Rev 2
218
Freescale Semiconductor
Chapter 13 Inter-Integrated Circuit (S08IICV1)
Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address
assignments for all IIC registers. This section refers to registers and control bits only by their names. A
Freescale-provided equate or header file is used to translate these names into the appropriate absolute
addresses.
13.3.1 IIC Address Register (IIC1A)
7
6
5
4
3
2
1
0
R
W
0
ADDR
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 13-3. IIC Address Register (IIC1A)
Table 13-1. IIC1A Register Field Descriptions
Description
Field
7:1
IIC Address Register — The ADDR contains the specific slave address to be used by the IIC module. This is
ADDR[7:1] the address the module will respond to when addressed as a slave.
13.3.2 IIC Frequency Divider Register (IIC1F)
7
6
5
4
3
2
1
0
R
W
MULT
ICR
Reset
0
0
0
0
0
0
0
0
Figure 13-4. IIC Frequency Divider Register (IIC1F)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
219
Chapter 13 Inter-Integrated Circuit (S08IICV1)
Table 13-2. IIC1A Register Field Descriptions
Field
Description
7:6
IIC Multiplier Factor — The MULT bits define the multiplier factor mul. This factor is used along with the SCL
MULT
divider to generate the IIC baud rate. The multiplier factor mul as defined by the MULT bits is provided below.
00 mul = 01
01 mul = 02
10 mul = 04
11 Reserved
5:0
ICR
IIC Clock Rate — The ICR bits are used to prescale the bus clock for bit rate selection. These bits are used to
define the SCL divider and the SDA hold value. The SCL divider multiplied by the value provided by the MULT
register (multiplier factor mul) is used to generate IIC baud rate.
IIC baud rate = bus speed (Hz)/(mul * SCL divider)
SDA hold time is the delay from the falling edge of the SCL (IIC clock) to the changing of SDA (IIC data). The
ICR is used to determine the SDA hold value.
SDA hold time = bus period (s) * SDA hold value
Table 13-3 provides the SCL divider and SDA hold values for corresponding values of the ICR. These values can
be used to set IIC baud rate and SDA hold time. For example:
Bus speed = 8 MHz
MULT is set to 01 (mul = 2)
Desired IIC baud rate = 100 kbps
IIC baud rate = bus speed (Hz)/(mul * SCL divider)
100000 = 8000000/(2*SCL divider)
SCL divider = 40
Table 13-3 shows that ICR must be set to 0B to provide an SCL divider of 40 and that this will result in an SDA
hold value of 9.
SDA hold time = bus period (s) * SDA hold value
SDA hold time = 1/8000000 * 9 = 1.125 μs
If the generated SDA hold value is not acceptable, the MULT bits can be used to change the ICR. This will result
in a different SDA hold value.
MC9S08AW60 Data Sheet, Rev 2
220
Freescale Semiconductor
Chapter 13 Inter-Integrated Circuit (S08IICV1)
Table 13-3. IIC Divider and Hold Values
ICR
(hex)
SDA Hold
Value
ICR
(hex)
SDA Hold
Value
SCL Divider
SCL Divider
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
22
7
7
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
160
192
17
17
24
8
224
33
26
8
256
33
28
9
288
49
30
9
320
49
34
10
10
7
384
65
40
480
65
28
320
33
32
7
384
33
36
9
448
65
40
9
512
65
44
11
11
13
13
9
576
97
48
640
97
56
768
129
129
65
68
960
48
640
56
9
768
65
64
13
13
17
17
21
21
9
896
129
129
193
193
257
257
129
129
257
257
385
385
513
513
72
1024
1152
1280
1536
1920
1280
1536
1792
2048
2304
2560
3072
3840
80
88
104
128
80
96
9
112
128
144
160
192
240
17
17
25
25
33
33
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
221
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.3.3 IIC Control Register (IIC1C)
7
6
5
4
3
2
1
0
R
W
0
0
0
IICEN
IICIE
MST
TX
TXAK
RSTA
0
Reset
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 13-5. IIC Control Register (IIC1C)
Table 13-4. IIC1C Register Field Descriptions
Description
Field
7
IIC Enable — The IICEN bit determines whether the IIC module is enabled.
IICEN
0 IIC is not enabled.
1 IIC is enabled.
6
IICIE
IIC Interrupt Enable — The IICIE bit determines whether an IIC interrupt is requested.
0 IIC interrupt request not enabled.
1 IIC interrupt request enabled.
5
Master Mode Select — The MST bit is changed from a 0 to a 1 when a START signal is generated on the bus
MST
and master mode is selected. When this bit changes from a 1 to a 0 a STOP signal is generated and the mode
of operation changes from master to slave.
0 Slave Mode.
1 Master Mode.
4
Transmit Mode Select — The TX bit selects the direction of master and slave transfers. In master mode this bit
TX
should be set according to the type of transfer required. Therefore, for address cycles, this bit will always be high.
When addressed as a slave this bit should be set by software according to the SRW bit in the status register.
0 Receive.
1 Transmit.
3
Transmit Acknowledge Enable — This bit specifies the value driven onto the SDA during data acknowledge
cycles for both master and slave receivers.
TXAK
0 An acknowledge signal will be sent out to the bus after receiving one data byte.
1 No acknowledge signal response is sent.
2
Repeat START — Writing a one to this bit will generate a repeated START condition provided it is the current
RSTA
master. This bit will always be read as a low. Attempting a repeat at the wrong time will result in loss of arbitration.
MC9S08AW60 Data Sheet, Rev 2
222
Freescale Semiconductor
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.3.4 IIC Status Register (IIC1S)
7
6
5
4
3
2
1
0
R
W
TCF
BUSY
0
SRW
RXAK
IAAS
ARBL
IICIF
Reset
1
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 13-6. IIC Status Register (IIC1S)
Table 13-5. IIC1S Register Field Descriptions
Description
Field
7
TCF
Transfer Complete Flag — This bit is set on the completion of a byte transfer. Note that this bit is only valid
during or immediately following a transfer to the IIC module or from the IIC module.The TCF bit is cleared by
reading the IIC1D register in receive mode or writing to the IIC1D in transmit mode.
0 Transfer in progress.
1 Transfer complete.
6
Addressed as a Slave — The IAAS bit is set when the calling address matches the programmed slave address.
IAAS
Writing the IIC1C register clears this bit.
0 Not addressed.
1 Addressed as a slave.
5
Bus Busy — The BUSY bit indicates the status of the bus regardless of slave or master mode. The BUSY bit is
BUSY
set when a START signal is detected and cleared when a STOP signal is detected.
0 Bus is idle.
1 Bus is busy.
4
Arbitration Lost — This bit is set by hardware when the arbitration procedure is lost. The ARBL bit must be
ARBL
cleared by software, by writing a one to it.
0 Standard bus operation.
1 Loss of arbitration.
2
Slave Read/Write — When addressed as a slave the SRW bit indicates the value of the R/W command bit of
the calling address sent to the master.
SRW
0 Slave receive, master writing to slave.
1 Slave transmit, master reading from slave.
1
IIC Interrupt Flag — The IICIF bit is set when an interrupt is pending. This bit must be cleared by software, by
IICIF
writing a one to it in the interrupt routine. One of the following events can set the IICIF bit:
•
•
•
One byte transfer completes
Match of slave address to calling address
Arbitration lost
0 No interrupt pending.
1 Interrupt pending.
0
Receive Acknowledge — When the RXAK bit is low, it indicates an acknowledge signal has been received after
RXAK
the completion of one byte of data transmission on the bus. If the RXAK bit is high it means that no acknowledge
signal is detected.
0 Acknowledge received.
1 No acknowledge received.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
223
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.3.5 IIC Data I/O Register (IIC1D)
7
6
5
4
3
2
1
0
R
W
DATA
Reset
0
0
0
0
0
0
0
0
Figure 13-7. IIC Data I/O Register (IIC1D)
Table 13-6. IIC1D Register Field Descriptions
Description
Field
7:0
Data — In master transmit mode, when data is written to the IIC1D, a data transfer is initiated. The most
DATA
significant bit is sent first. In master receive mode, reading this register initiates receiving of the next byte of data.
NOTE
When transmitting out of master receive mode, the IIC mode should be
switched before reading the IIC1D register to prevent an inadvertent
initiation of a master receive data transfer.
In slave mode, the same functions are available after an address match has occurred.
Note that the TX bit in IIC1C must correctly reflect the desired direction of transfer in master and slave
modes for the transmission to begin. For instance, if the IIC is configured for master transmit but a master
receive is desired, then reading the IIC1D will not initiate the receive.
Reading the IIC1D will return the last byte received while the IIC is configured in either master receive or
slave receive modes. The IIC1D does not reflect every byte that is transmitted on the IIC bus, nor can
software verify that a byte has been written to the IIC1D correctly by reading it back.
In master transmit mode, the first byte of data written to IIC1D following assertion of MST is used for the
address transfer and should comprise of the calling address (in bit 7–bit 1) concatenated with the required
R/W bit (in position bit 0).
MC9S08AW60 Data Sheet, Rev 2
224
Freescale Semiconductor
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.4 Functional Description
This section provides a complete functional description of the IIC module.
13.4.1 IIC Protocol
The IIC bus system uses a serial data line (SDA) and a serial clock line (SCL) for data transfer. All devices
connected to it must have open drain or open collector outputs. A logic AND function is exercised on both
lines with external pull-up resistors. The value of these resistors is system dependent.
Normally, a standard communication is composed of four parts:
•
•
•
•
START signal
Slave address transmission
Data transfer
STOP signal
The STOP signal should not be confused with the CPU STOP instruction. The IIC bus system
communication is described briefly in the following sections and illustrated in Figure 13-8.
MSB
1
LSB
8
MSB
1
LSB
8
SCL
SDA
2
3
4
5
6
7
9
2
3
4
5
6
7
9
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W
XXX
D7 D6 D5 D4 D3 D2 D1 D0
START
SIGNAL
CALLING ADDRESS
READ/ ACK
BIT
WRITE
DATA BYTE
NO STOP
ACK SIGNAL
BIT
MSB
1
LSB
MSB
LSB
8
SCL
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
9
SDA
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W
XX
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W
START
SIGNAL
CALLING ADDRESS
READ/ ACK REPEATED
BIT START
SIGNAL
NEW CALLING ADDRESS
NO STOP
ACK SIGNAL
BIT
READ/
WRITE
WRITE
Figure 13-8. IIC Bus Transmission Signals
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
225
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.4.1.1 START Signal
When the bus is free; i.e., no master device is engaging the bus (both SCL and SDA lines are at logical
high), a master may initiate communication by sending a START signal. As shown in Figure 13-8, a
START signal is defined as a high-to-low transition of SDA while SCL is high. This signal denotes the
beginning of a new data transfer (each data transfer may contain several bytes of data) and brings all slaves
out of their idle states.
13.4.1.2 Slave Address Transmission
The first byte of data transferred immediately after the START signal is the slave address transmitted by
the master. This is a seven-bit calling address followed by a R/W bit. The R/W bit tells the slave the desired
direction of data transfer.
1 = Read transfer, the slave transmits data to the master.
0 = Write transfer, the master transmits data to the slave.
Only the slave with a calling address that matches the one transmitted by the master will respond by
sending back an acknowledge bit. This is done by pulling the SDA low at the 9th clock (see Figure 13-8).
No two slaves in the system may have the same address. If the IIC module is the master, it must not transmit
an address that is equal to its own slave address. The IIC cannot be master and slave at the same time.
However, if arbitration is lost during an address cycle, the IIC will revert to slave mode and operate
correctly even if it is being addressed by another master.
13.4.1.3 Data Transfer
Before successful slave addressing is achieved, the data transfer can proceed byte-by-byte in a direction
specified by the R/W bit sent by the calling master.
All transfers that come after an address cycle are referred to as data transfers, even if they carry sub-address
information for the slave device
Each data byte is 8 bits long. Data may be changed only while SCL is low and must be held stable while
SCL is high as shown in Figure 13-8. There is one clock pulse on SCL for each data bit, the MSB being
transferred first. Each data byte is followed by a 9th (acknowledge) bit, which is signalled from the
receiving device. An acknowledge is signalled by pulling the SDA low at the ninth clock. In summary, one
complete data transfer needs nine clock pulses.
If the slave receiver does not acknowledge the master in the 9th bit time, the SDA line must be left high
by the slave. The master interprets the failed acknowledge as an unsuccessful data transfer.
If the master receiver does not acknowledge the slave transmitter after a data byte transmission, the slave
interprets this as an end of data transfer and releases the SDA line.
In either case, the data transfer is aborted and the master does one of two things:
•
•
Relinquishes the bus by generating a STOP signal.
Commences a new calling by generating a repeated START signal.
MC9S08AW60 Data Sheet, Rev 2
226
Freescale Semiconductor
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.4.1.4 STOP Signal
The master can terminate the communication by generating a STOP signal to free the bus. However, the
master may generate a START signal followed by a calling command without generating a STOP signal
first. This is called repeated START. A STOP signal is defined as a low-to-high transition of SDA while
SCL at logical 1 (see Figure 13-8).
The master can generate a STOP even if the slave has generated an acknowledge at which point the slave
must release the bus.
13.4.1.5 Repeated START Signal
As shown in Figure 13-8, a repeated START signal is a START signal generated without first generating a
STOP signal to terminate the communication. This is used by the master to communicate with another
slave or with the same slave in different mode (transmit/receive mode) without releasing the bus.
13.4.1.6 Arbitration Procedure
The IIC bus is a true multi-master bus that allows more than one master to be connected on it. If two or
more masters try to control the bus at the same time, a clock synchronization procedure determines the bus
clock, for which the low period is equal to the longest clock low period and the high is equal to the shortest
one among the masters. The relative priority of the contending masters is determined by a data arbitration
procedure, a bus master loses arbitration if it transmits logic 1 while another master transmits logic 0. The
losing masters immediately switch over to slave receive mode and stop driving SDA output. In this case,
the transition from master to slave mode does not generate a STOP condition. Meanwhile, a status bit is
set by hardware to indicate loss of arbitration.
13.4.1.7 Clock Synchronization
Because wire-AND logic is performed on the SCL line, a high-to-low transition on the SCL line affects all
the devices connected on the bus. The devices start counting their low period and after a device’s clock has
gone low, it holds the SCL line low until the clock high state is reached. However, the change of low to
high in this device clock may not change the state of the SCL line if another device clock is still within its
low period. Therefore, synchronized clock SCL is held low by the device with the longest low period.
Devices with shorter low periods enter a high wait state during this time (see Figure 13-9). When all
devices concerned have counted off their low period, the synchronized clock SCL line is released and
pulled high. There is then no difference between the device clocks and the state of the SCL line and all the
devices start counting their high periods. The first device to complete its high period pulls the SCL line
low again.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
227
Chapter 13 Inter-Integrated Circuit (S08IICV1)
START COUNTING HIGH PERIOD
DELAY
SCL1
SCL2
SCL
INTERNAL COUNTER RESET
Figure 13-9. IIC Clock Synchronization
13.4.1.8 Handshaking
The clock synchronization mechanism can be used as a handshake in data transfer. Slave devices may hold
the SCL low after completion of one byte transfer (9 bits). In such case, it halts the bus clock and forces
the master clock into wait states until the slave releases the SCL line.
13.4.1.9 Clock Stretching
The clock synchronization mechanism can be used by slaves to slow down the bit rate of a transfer. After
the master has driven SCL low the slave can drive SCL low for the required period and then release it. If
the slave SCL low period is greater than the master SCL low period then the resulting SCL bus signal low
period is stretched.
13.5 Resets
The IIC is disabled after reset. The IIC cannot cause an MCU reset.
13.6 Interrupts
The IIC generates a single interrupt.
An interrupt from the IIC is generated when any of the events in Table 13-7 occur provided the IICIE bit
is set. The interrupt is driven by bit IICIF (of the IIC status register) and masked with bit IICIE (of the IIC
control register). The IICIF bit must be cleared by software by writing a one to it in the interrupt routine.
The user can determine the interrupt type by reading the status register.
Table 13-7. Interrupt Summary
Interrupt Source
Status
Flag
Local Enable
Complete 1-byte transfer
Match of received calling address
Arbitration Lost
TCF
IAAS
ARBL
IICIF
IICIF
IICIF
IICIE
IICIE
IICIE
MC9S08AW60 Data Sheet, Rev 2
228
Freescale Semiconductor
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.6.1 Byte Transfer Interrupt
The TCF (transfer complete flag) bit is set at the falling edge of the 9th clock to indicate the completion of
byte transfer.
13.6.2 Address Detect Interrupt
When the calling address matches the programmed slave address (IIC address register), the IAAS bit in
the status register is set. The CPU is interrupted provided the IICIE is set. The CPU must check the SRW
bit and set its Tx mode accordingly.
13.6.3 Arbitration Lost Interrupt
The IIC is a true multi-master bus that allows more than one master to be connected on it. If two or more
masters try to control the bus at the same time, the relative priority of the contending masters is determined
by a data arbitration procedure. The IIC module asserts this interrupt when it loses the data arbitration
process and the ARBL bit in the status register is set.
Arbitration is lost in the following circumstances:
•
•
SDA sampled as a low when the master drives a high during an address or data transmit cycle.
SDA sampled as a low when the master drives a high during the acknowledge bit of a data receive
cycle.
•
•
•
A START cycle is attempted when the bus is busy.
A repeated START cycle is requested in slave mode.
A STOP condition is detected when the master did not request it.
This bit must be cleared by software by writing a one to it.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
229
Chapter 13 Inter-Integrated Circuit (S08IICV1)
13.7 Initialization/Application Information
Module Initialization (Slave)
1. Write: IICA
—
to set the slave address
2. Write: IICC
—
to enable IIC and interrupts
3. Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data
4. Initialize RAM variables used to achieve the routine shown in Figure 13-11
Module Initialization (Master)
1. Write: IICF
—
to set the IIC baud rate (example provided in this chapter)
2. Write: IICC
—
to enable IIC and interrupts
3. Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data
4. Initialize RAM variables used to achieve the routine shown in Figure 13-11
5. Write: IICC
—
to enable TX
6. Write: IICC
—
to enable MST (master mode)
7. Write: IICD
—
with the address of the target slave. (The LSB of this byte will determine whether the communication is
master receive or transmit.)
Module Use
The routine shown in Figure 13-11 can handle both master and slave IIC operations. For slave operation, an
incoming IIC message that contains the proper address will begin IIC communication. For master operation,
communication must be initiated by writing to the IICD register.
Register Model
ADDR
Address to which the module will respond when addressed as a slave (in slave mode)
MULT
Baud rate = BUSCLK / (2 x MULT x (SCL DIVIDER))
0
IICA
IICF
ICR
IICEN
Module configuration
TCF IAAS
Module status flags
IICIE
MST
TX
TXAK
RSTA
0
0
IICC
IICS
IICD
BUSY
ARBL
0
SRW
IICIF
RXAK
DATA
Data register; Write to transmit IIC data read to read IIC data
Figure 13-10. IIC Module Quick Start
MC9S08AW60 Data Sheet, Rev 2
230
Freescale Semiconductor
Chapter 13 Inter-Integrated Circuit (S08IICV1)
Clear
IICIF
Master
Mode
?
Y
N
Y
Arbitration
Lost
TX
RX
Tx/Rx
?
?
N
Last Byte
Transmitted
Clear ARBL
Y
N
?
N
Last
Byte to Be Read
?
Y
N
RXAK=0
?
IAAS=1
?
IAAS=1
?
Y
N
Y
Y
N
Data Transfer
Address Transfer
Y
End of
Addr Cycle
(Master Rx)
?
2nd Last
Byte to Be Read
?
(Read)
Y
Y
SRW=1
?
TX/RX
?
RX
TX
(Write)
N
N
N
ACK from
Receiver
?
Y
Generate
Stop Signal
(MST = 0)
Write Next
Byte to IICD
Set TX
Mode
Set TXACK =1
N
Read Data
from IICD
and Store
Tx Next
Byte
Write Data
to IICD
Switch to
Rx Mode
Set RX
Mode
Switch to
Rx Mode
Generate
Stop Signal
(MST = 0)
Read Data
from IICD
and Store
Dummy Read
from IICD
Dummy Read
from IICD
Dummy Read
from IICD
RTI
Figure 13-11. Typical IIC Interrupt Routine
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
231
Chapter 13 Inter-Integrated Circuit (S08IICV1)
MC9S08AW60 Data Sheet, Rev 2
232
Freescale Semiconductor
Chapter 14
Analog-to-Digital Converter (S08ADC10V1)
14.1 Overview
The 10-bit analog-to-digital converter (ADC) is a successive approximation ADC designed for operation
within an integrated microcontroller system-on-chip. The ADC module design supports up to 28 separate
analog inputs (AD0-AD27). Only 18 (AD0-AD15, AD26, and AD27) of the possible inputs are
implemented on the MC9S08AW60 Series of MCUs. These inputs are selected by the ADCH bits. Some
inputs are shared with I/O pins as shown in Figure 14-1. All of the channel assignments of the ADC for
the MC9S08AW60 Series devices are summarized in Table 14-1.
14.2 Channel Assignments
The ADC channel assignments for the MC9S08AW60 Series devices are shown in the table below.
Channels that are unimplemented are internally connected to V
. Reserved channels convert to an
REFL
unknown value. Channels which are connected to an I/O pin have an associated pin control bit as shown.
Table 14-1. ADC Channel Assignment
ADCH
Channel
Input
Pin Control
ADCH
Channel
Input
Pin Control
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
PTB0/ADC1P0
PTB1/ADC1P1
PTB2/ADC1P2
PTB3/ADC1P3
PTB4/ADC1P4
PTB5/ADC1P5
PTB6/ADC1P6
PTB7/ADC1P7
PTD0/ADC1P8
PTD1/ADC1P9
ADPC0
ADPC1
ADPC2
ADPC3
ADPC4
ADPC5
ADPC6
ADPC7
ADPC8
ADPC9
ADPC10
10000
10001
10010
10011
10100
10101
10110
10111
11000
11001
11010
AD16
AD17
AD18
AD19
AD20
AD21
AD22
AD23
AD24
AD25
AD26
VREFL
VREFL
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
VREFL
VREFL
VREFL
VREFL
Reserved
Reserved
Reserved
Reserved
PTD2/ADC1P10/
KBI1P5
Temperature
Sensor1
01011
01100
01101
AD11
AD12
AD13
PTD3/ADC1P11/
KBI1P6
ADPC11
ADPC12
ADPC13
11011
11100
11101
AD27
Internal Bandgap
N/A
N/A
N/A
PTD4/ADC1P12/
TPM2CLK
Reserved
—
PTD5/ADC1P13
VREFH
VREFH
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
233
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
Table 14-1. ADC Channel Assignment (continued)
ADCH
Channel
Input
Pin Control
ADCH
Channel
Input
Pin Control
01110
AD14
PTD6/ADC1P14/
TPM1CLK
ADPC14
11110
VREFL
VREFL
N/A
01111
AD15
PTD7ADC1P15/
KBI1P7
ADPC15
11111
Module
disabled
None
N/A
1
For more information, see Section 14.2.3, “Temperature Sensor.”
NOTE
Selecting the internal bandgap channel requires BGBE =1 in SPMSC1 see
Section 5.9.8, “System Power Management Status and Control 1 Register
(SPMSC1).” For value of bandgap voltage reference see Section Table A-7.,
“DC Characteristics.”
14.2.1 Alternate Clock
The ADC module is capable of performing conversions using the MCU bus clock, the bus clock divided
by two, the local asynchronous clock (ADACK) within the module, or the alternate clock, ALTCLK. The
alternate clock for the MC9S08AW60 Series MCU devices is the external reference clock (ICGERCLK)
from the internal clock generator (ICG) module.
Because ICGERCLK is active only while an external clock source is enabled, the ICG must be configured
for either FBE or FEE mode (CLKS1 = 1). ICGERCLK must run at a frequency such that the ADC
conversion clock (ADCK) runs at a frequency within its specified range (f
) after being divided down
ADCK
from the ALTCLK input as determined by the ADIV bits. For example, if the ADIV bits are set up to divide
by four, then the minimum frequency for ALTCLK (ICGERCLK) is four times the minimum value for
f
and the maximum frequency is four times the maximum value for f
. Because of the minimum
ADCK
ADCK
frequency requirement, when an oscillator circuit is used it must be configured for high range operation
(RANGE = 1).
ALTCLK is active while the MCU is in wait mode provided the conditions described above are met. This
allows ALTCLK to be used as the conversion clock source for the ADC while the MCU is in wait mode.
ALTCLK cannot be used as the ADC conversion clock source while the MCU is in stop3.
14.2.2 Hardware Trigger
The ADC hardware trigger, ADHWT, is output from the real time interrupt (RTI) counter. The RTI counter
can be clocked by either ICGERCLK or a nominal 1 kHz clock source within the RTI block. The 1-kHz
clock source can be used with the MCU in run, wait, or stop3. With the ICG configured for either FBE or
FEE mode, ICGERCLK can be used with the MCU in run or wait.
The period of the RTI is determined by the input clock frequency and the RTIS bits. When the ADC
hardware trigger is enabled, a conversion is initiated upon an RTI counter overflow. The RTI counter is a
free running counter that generates an overflow at the RTI rate determined by the RTIS bits.
MC9S08AW60 Data Sheet, Rev 2
234
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
14.2.2.1 Analog Pin Enables
The ADC on MC9S08AW60 Series contains only two analog pin enable registers, APCTL1 and APCTL2.
14.2.2.2 Low-Power Mode Operation
The ADC is capable of running in stop3 mode but requires LVDSE and LVDE in SPMSC1 to be set.
14.2.3 Temperature Sensor
The ADC1 module includes a temperature sensor whose output is connected to one of the ADC analog
channel inputs. Equation 14-1 provides an approximate transfer function of the temperature sensor.
Temp = 25 - ((V
-V
) ÷ m)
TEMP25
Eqn. 14-1
TEMP
where:
— V
— V
is the voltage of the temperature sensor channel at the ambient temperature.
TEMP
is the voltage of the temperature sensor channel at 25°C.
TEMP25
— m is the hot or cold voltage versus temperature slope in V/°C.
For temperature calculations, use the V and m values from the ADC Electricals table.
TEMP25
In application code, the user reads the temperature sensor channel, calculates V
, and compares to
TEMP
V
. If V
is greater than V
the cold slope value is applied in Equation 14-1. If V
is
TEMP25
TEMP
TEMP25
TEMP
less than V
the hot slope value is applied in Equation 14-1.
TEMP25
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
235
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
HCS08 CORE
DEBUG
MODULE (DBG)
8
PTA7– PTA0
BKGD/MS
BDC
CPU
8
PTB7/AD1P7–
PTB0/AD1P0
HCS08 SYSTEM CONTROL
RESET
IRQ
PTC6
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
RxD2
TxD2
PTC5/RxD2
PTC4
PTC3/TxD2
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI2)
PTC2/MCLK
PTC1/SDA1
SDA1
SCL1
RTI
COP
LVD
IIC MODULE (IIC1)
PTC0/SCL1
IRQ
AD1P7–AD1P0
8
V
DDAD
8
10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC1)
AD1P15–AD1P8
V
V
SSAD
REFL
PTD7/AD1P15/KBI1P7
PTD6/AD1P14/TPM1CLK
PTD5/AD1P13
PTD4/AD1P12/TPM2CLK
PTD3/AD1P11/KBI1P6
PTD2/AD1P10/KBI1P5
PTD1/AD1P9
V
REFH
USER FLASH
(AW60 = 63,280 BYTES)
(AW48 = 49,152 BYTES)
(AW32 = 32,768 BYTES)
(AW16 = 16,384 BYTES)
PTD0/AD1P8
SPSCK1
PTE7/SPSCK1
PTE6/MOSI1
MOSI1
SERIAL PERIPHERAL
USER RAM
MISO1
SS1
INTERFACE MODULE (SPI1)
PTE5/MISO1
PTE4/SS1
AW60/48/32 = 2048 BYTES
AW16 = 1024 BYTES
TPM1CLK
PTE3/TPM1CH1
PTE2/TPM1CH0
6-CHANNEL TIMER/PWM
MODULE (TPM1)
TPM1CH5–
TPM1CH0
INTERNAL CLOCK
GENERATOR (ICG)
6
RxD1
TxD1
PTE1/RxD1
PTE0/TxD1
PTF7
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI1)
LOW-POWER OSCILLATOR
PTF6
PTF5/TPM2CH1
PTF4/TPM2CH0
TPM2CLK
V
DD
VOLTAGE
REGULATOR
2-CHANNEL TIMER/PWM
MODULE (TPM2)
TPM2CH1–TPM2CH0
V
SS
2
PTF3/TPM1CH5
KBI1P7–KBI1P5
3
PTF2/TPM1CH4
PTF1/TPM1CH3
PTF0/TPM1CH2
8-BIT KEYBOARD
INTERRUPT MODULE (KBI1)
KBI1P4–KBI1P0
5
EXTAL
XTAL
PTG6/EXTAL
PTG5/XTAL
NOTES:
PTG4/KBI1P4
PTG3/KBI1P3
PTG2/KBI1P2
PTG1/KBI1P1
PTG0/KBI1P0
1. Port pins are software configurable with pullup device if input port.
2. Pin contains software configurable pullup/pulldown device if IRQ is enabled
(IRQPE = 1). Pulldown is enabled if rising edge detect is selected (IRQEDG = 1)
3. IRQ does not have a clamp diode to VDD. IRQ should not be driven above VDD
4. Pin contains integrated pullup device.
.
5. Pins PTD7, PTD3, PTD2, and PTG4 contain both pullup and pulldown devices.
Pulldown enabled when KBI is enabled (KBIPEn = 1) and rising edge is selected
(KBEDGn = 1).
Figure 14-1. MC9S08AW60 Block Diagram Highlighting ADC Block and Pins
MC9S08AW60 Data Sheet, Rev 2
236
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
14.2.4 Features
Features of the ADC module include:
•
•
•
•
•
•
•
•
•
•
•
Linear successive approximation algorithm with 10 bits resolution.
Up to 28 analog inputs.
Output formatted in 10- or 8-bit right-justified format.
Single or continuous conversion (automatic return to idle after single conversion).
Configurable sample time and conversion speed/power.
Conversion complete flag and interrupt.
Input clock selectable from up to four sources.
Operation in wait or stop3 modes for lower noise operation.
Asynchronous clock source for lower noise operation.
Selectable asynchronous hardware conversion trigger.
Automatic compare with interrupt for less-than, or greater-than or equal-to, programmable value.
14.2.5 Block Diagram
Figure 14-2 provides a block diagram of the ADC module
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
237
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
Compare true
ADC1SC1
3
ADC1CFG
Async
Clock Gen
1
2
ADACK
Bus Clock
ALTCLK
MCU STOP
ADHWT
ADCK
Clock
Divide
Control Sequencer
÷2
AD0
1
2
AIEN
Interrupt
COCO
ADVIN
SAR Converter
AD27
V
V
REFH
Data Registers
REFL
Compare true
ADC1SC2
3
Compare
Logic
Compare Value Registers
Figure 14-2. ADC Block Diagram
14.3 External Signal Description
The ADC module supports up to 28 separate analog inputs. It also requires four supply/reference/ground
connections.
Table 14-2. Signal Properties
Name
Function
AD27–AD0
VREFH
Analog Channel inputs
High reference voltage
Low reference voltage
Analog power supply
Analog ground
VREFL
VDDAD
VSSAD
MC9S08AW60 Data Sheet, Rev 2
238
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
14.3.1 Analog Power (VDDAD
)
The ADC analog portion uses V
as its power connection. In some packages, V
is connected
DDAD
DDAD
internally to V . If externally available, connect the V
pin to the same voltage potential as V
.
DD
DDAD
DD
External filtering may be necessary to ensure clean V
for good results.
DDAD
14.3.2 Analog Ground (VSSAD
)
The ADC analog portion uses V
as its ground connection. In some packages, V
is connected
SSAD
SSAD
internally to V . If externally available, connect the V
pin to the same voltage potential as V .
SS
SSAD
SS
14.3.3 Voltage Reference High (VREFH
)
V
V
is the high reference voltage for the converter. In some packages, V
is connected internally to
REFH
REFH
. If externally available, V
may be connected to the same potential as V
, or may be
DDAD
REFH
DDAD
driven by an external source that is between the minimum V
spec and the V
potential (V
DDAD
DDAD REFH
must never exceed V
).
DDAD
14.3.4 Voltage Reference Low (VREFL
)
V
V
is the low reference voltage for the converter. In some packages, V
is connected internally to
REFL
REFL
SSAD
. If externally available, connect the V
pin to the same voltage potential as V
.
REFL
SSAD
14.3.5 Analog Channel Inputs (ADx)
The ADC module supports up to 28 separate analog inputs. An input is selected for conversion through the
ADCH channel select bits.
14.4 Register Definition
These memory mapped registers control and monitor operation of the ADC:
•
•
•
•
•
•
Status and control register, ADC1SC1
Status and control register, ADC1SC2
Data result registers, ADC1RH and ADC1RL
Compare value registers, ADC1CVH and ADC1CVL
Configuration register, ADC1CFG
Pin enable registers, APCTL1, APCTL2, APCTL3
14.4.1 Status and Control Register 1 (ADC1SC1)
This section describes the function of the ADC status and control register (ADC1SC1). Writing ADC1SC1
aborts the current conversion and initiates a new conversion (if the ADCH bits are equal to a value other
than all 1s).
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
239
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
7
6
5
4
3
2
1
0
R
W
COCO
AIEN
ADCO
ADCH
Reset:
0
0
0
1
1
1
1
1
= Unimplemented or Reserved
Figure 14-3. Status and Control Register (ADC1SC1)
Table 14-3. ADC1SC1 Register Field Descriptions
Description
Field
7
Conversion Complete Flag — The COCO flag is a read-only bit which is set each time a conversion is
completed when the compare function is disabled (ACFE = 0). When the compare function is enabled (ACFE =
1) the COCO flag is set upon completion of a conversion only if the compare result is true. This bit is cleared
whenever ADC1SC1 is written or whenever ADC1RL is read.
COCO
0 Conversion not completed
1 Conversion completed
6
Interrupt Enable — AIEN is used to enable conversion complete interrupts. When COCO becomes set while
AIEN is high, an interrupt is asserted.
AIEN
0 Conversion complete interrupt disabled
1 Conversion complete interrupt enabled
5
Continuous Conversion Enable — ADCO is used to enable continuous conversions.
ADCO
0 One conversion following a write to the ADC1SC1 when software triggered operation is selected, or one
conversion following assertion of ADHWT when hardware triggered operation is selected.
1 Continuous conversions initiated following a write to ADC1SC1 when software triggered operation is selected.
Continuous conversions are initiated by an ADHWT event when hardware triggered operation is selected.
4:0
ADCH
Input Channel Select — The ADCH bits form a 5-bit field which is used to select one of the input channels. The
input channels are detailed in Figure 14-4.
The successive approximation converter subsystem is turned off when the channel select bits are all set to 1.
This feature allows for explicit disabling of the ADC and isolation of the input channel from all sources.
Terminating continuous conversions this way will prevent an additional, single conversion from being performed.
It is not necessary to set the channel select bits to all 1s to place the ADC in a low-power state when continuous
conversions are not enabled because the module automatically enters a low-power state when a conversion
completes.
Figure 14-4. Input Channel Select
ADCH
Input Select
ADCH
Input Select
00000
00001
00010
00011
00100
00101
00110
00111
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
10000
10001
10010
10011
10100
10101
10110
10111
AD16
AD17
AD18
AD19
AD20
AD21
AD22
AD23
MC9S08AW60 Data Sheet, Rev 2
240
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
Figure 14-4. Input Channel Select (continued)
ADCH
Input Select
ADCH
Input Select
01000
01001
01010
01011
01100
01101
01110
01111
AD8
AD9
11000
11001
11010
11011
11100
11101
11110
11111
AD24
AD25
AD10
AD11
AD12
AD13
AD14
AD15
AD26
AD27
Reserved
VREFH
VREFL
Module disabled
14.4.2 Status and Control Register 2 (ADC1SC2)
The ADC1SC2 register is used to control the compare function, conversion trigger and conversion active
of the ADC module.
7
6
5
4
3
2
1
0
R
W
ADACT
0
0
ADTRG
ACFE
ACFGT
R1
R1
Reset:
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
1
Bits 1 and 0 are reserved bits that must always be written to 0.
Figure 14-5. Status and Control Register 2 (ADC1SC2)
Table 14-4. ADC1SC2 Register Field Descriptions
Description
Field
7
Conversion Active — ADACT indicates that a conversion is in progress. ADACT is set when a conversion is
initiated and cleared when a conversion is completed or aborted.
0 Conversion not in progress
ADACT
1 Conversion in progress
6
Conversion Trigger Select — ADTRG is used to select the type of trigger to be used for initiating a conversion.
Two types of trigger are selectable: software trigger and hardware trigger. When software trigger is selected, a
conversion is initiated following a write to ADC1SC1. When hardware trigger is selected, a conversion is initiated
following the assertion of the ADHWT input.
ADTRG
0 Software trigger selected
1 Hardware trigger selected
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
241
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
Table 14-4. ADC1SC2 Register Field Descriptions (continued)
Field
Description
5
Compare Function Enable — ACFE is used to enable the compare function.
0 Compare function disabled
ACFE
1 Compare function enabled
4
Compare Function Greater Than Enable — ACFGT is used to configure the compare function to trigger when
the result of the conversion of the input being monitored is greater than or equal to the compare value. The
compare function defaults to triggering when the result of the compare of the input being monitored is less than
the compare value.
ACFGT
0 Compare triggers when input is less than compare level
1 Compare triggers when input is greater than or equal to compare level
14.4.3 Data Result High Register (ADC1RH)
ADC1RH contains the upper two bits of the result of a 10-bit conversion. When configured for 8-bit
conversions both ADR8 and ADR9 are equal to zero. ADC1RH is updated each time a conversion
completes except when automatic compare is enabled and the compare condition is not met. In 10-bit
MODE, reading ADC1RH prevents the ADC from transferring subsequent conversion results into the
result registers until ADC1RL is read. If ADC1RL is not read until after the next conversion is completed,
then the intermediate conversion result will be lost. In 8-bit mode there is no interlocking with ADC1RL.
In the case that the MODE bits are changed, any data in ADC1RH becomes invalid.
7
6
5
4
3
2
1
0
R
W
0
0
0
0
0
0
ADR9
ADR8
Reset:
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 14-6. Data Result High Register (ADC1RH)
14.4.4 Data Result Low Register (ADC1RL)
ADC1RL contains the lower eight bits of the result of a 10-bit conversion, and all eight bits of an 8-bit
conversion. This register is updated each time a conversion completes except when automatic compare is
enabled and the compare condition is not met. In 10-bit mode, reading ADC1RH prevents the ADC from
transferring subsequent conversion results into the result registers until ADC1RL is read. If ADC1RL is
not read until the after next conversion is completed, then the intermediate conversion results will be lost.
In 8-bit mode, there is no interlocking with ADC1RH. In the case that the MODE bits are changed, any
data in ADC1RL becomes invalid.
MC9S08AW60 Data Sheet, Rev 2
242
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
7
6
5
4
3
2
1
0
R
W
ADR7
ADR6
ADR5
ADR4
ADR3
ADR2
ADR1
ADR0
Reset:
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 14-7. Data Result Low Register (ADC1RL)
14.4.5 Compare Value High Register (ADC1CVH)
This register holds the upper two bits of the 10-bit compare value. These bits are compared to the upper
two bits of the result following a conversion in 10-bit mode when the compare function is enabled.In 8-bit
operation, ADC1CVH is not used during compare.
7
6
5
4
3
2
1
0
R
W
0
0
0
0
ADCV9
ADCV8
Reset:
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 14-8. Compare Value High Register (ADC1CVH)
14.4.6 Compare Value Low Register (ADC1CVL)
This register holds the lower 8 bits of the 10-bit compare value, or all 8 bits of the 8-bit compare value.
Bits ADCV7:ADCV0 are compared to the lower 8 bits of the result following a conversion in either 10-bit
or 8-bit mode.
7
6
5
4
3
2
1
0
R
W
ADCV7
ADCV6
ADCV5
ADCV4
ADCV3
ADCV2
ADCV1
ADCV0
Reset:
0
0
0
0
0
0
0
0
Figure 14-9. Compare Value Low Register(ADC1CVL)
14.4.7 Configuration Register (ADC1CFG)
ADC1CFG is used to select the mode of operation, clock source, clock divide, and configure for low power
or long sample time.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
243
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
7
6
5
4
3
2
1
0
R
W
ADLPC
ADIV
ADLSMP
MODE
ADICLK
Reset:
0
0
0
0
0
0
0
0
Figure 14-10. Configuration Register (ADC1CFG)
Table 14-5. ADC1CFG Register Field Descriptions
Description
Field
7
Low Power Configuration — ADLPC controls the speed and power configuration of the successive
approximation converter. This is used to optimize power consumption when higher sample rates are not required.
0 High speed configuration
ADLPC
1 Low power configuration: {FC31}The power is reduced at the expense of maximum clock speed.
6:5
Clock Divide Select — ADIV select the divide ratio used by the ADC to generate the internal clock ADCK.
ADIV
Table 14-6 shows the available clock configurations.
4
Long Sample Time Configuration — ADLSMP selects between long and short sample time. This adjusts the
ADLSMP sample period to allow higher impedance inputs to be accurately sampled or to maximize conversion speed for
lower impedance inputs. Longer sample times can also be used to lower overall power consumption when
continuous conversions are enabled if high conversion rates are not required.
0 Short sample time
1 Long sample time
3:2
Conversion Mode Selection — MODE bits are used to select between 10- or 8-bit operation. See Table 14-7.
MODE
1:0
Input Clock Select — ADICLK bits select the input clock source to generate the internal clock ADCK. See
ADICLK
Table 14-8.
Table 14-6. Clock Divide Select
ADIV
Divide Ratio
Clock Rate
00
01
10
11
1
2
4
8
Input clock
Input clock ÷ 2
Input clock ÷ 4
Input clock ÷ 8
Table 14-7. Conversion Modes
Mode Description
MODE
00
01
10
11
8-bit conversion (N=8)
Reserved
10-bit conversion (N=10)
Reserved
MC9S08AW60 Data Sheet, Rev 2
244
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
Table 14-8. Input Clock Select
ADICLK
Selected Clock Source
00
01
10
11
Bus clock
Bus clock divided by 2
Alternate clock (ALTCLK)
Asynchronous clock (ADACK)
14.4.8 Pin Control 1 Register (APCTL1)
The pin control registers are used to disable the I/O port control of MCU pins used as analog inputs.
APCTL1 is used to control the pins associated with channels 0–7 of the ADC module.
7
6
5
4
3
2
1
0
R
W
ADPC7
ADPC6
ADPC5
ADPC4
ADPC3
ADPC2
ADPC1
ADPC0
Reset:
0
0
0
0
0
0
0
0
Figure 14-11. Pin Control 1 Register (APCTL1)
Table 14-9. APCTL1 Register Field Descriptions
Description
Field
7
ADC Pin Control 7 — ADPC7 is used to control the pin associated with channel AD7.
0 AD7 pin I/O control enabled
ADPC7
1 AD7 pin I/O control disabled
6
ADC Pin Control 6 — ADPC6 is used to control the pin associated with channel AD6.
0 AD6 pin I/O control enabled
ADPC6
1 AD6 pin I/O control disabled
5
ADC Pin Control 5 — ADPC5 is used to control the pin associated with channel AD5.
0 AD5 pin I/O control enabled
ADPC5
1 AD5 pin I/O control disabled
4
ADC Pin Control 4 — ADPC4 is used to control the pin associated with channel AD4.
0 AD4 pin I/O control enabled
ADPC4
1 AD4 pin I/O control disabled
3
ADC Pin Control 3 — ADPC3 is used to control the pin associated with channel AD3.
0 AD3 pin I/O control enabled
ADPC3
1 AD3 pin I/O control disabled
2
ADC Pin Control 2 — ADPC2 is used to control the pin associated with channel AD2.
0 AD2 pin I/O control enabled
ADPC2
1 AD2 pin I/O control disabled
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
245
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
Table 14-9. APCTL1 Register Field Descriptions (continued)
Field
Description
1
ADC Pin Control 1 — ADPC1 is used to control the pin associated with channel AD1.
0 AD1 pin I/O control enabled
ADPC1
1 AD1 pin I/O control disabled
0
ADC Pin Control 0 — ADPC0 is used to control the pin associated with channel AD0.
0 AD0 pin I/O control enabled
ADPC0
1 AD0 pin I/O control disabled
14.4.9 Pin Control 2 Register (APCTL2)
APCTL2 is used to control channels 8–15 of the ADC module.
7
6
5
4
3
2
1
0
R
W
ADPC15
ADPC14
ADPC13
ADPC12
ADPC11
ADPC10
ADPC9
ADPC8
Reset:
0
0
0
0
0
0
0
0
Figure 14-12. Pin Control 2 Register (APCTL2)
Table 14-10. APCTL2 Register Field Descriptions
Description
Field
7
ADC Pin Control 15 — ADPC15 is used to control the pin associated with channel AD15.
ADPC15 0 AD15 pin I/O control enabled
1 AD15 pin I/O control disabled
6
ADC Pin Control 14 — ADPC14 is used to control the pin associated with channel AD14.
ADPC14 0 AD14 pin I/O control enabled
1 AD14 pin I/O control disabled
5
ADC Pin Control 13 — ADPC13 is used to control the pin associated with channel AD13.
ADPC13 0 AD13 pin I/O control enabled
1 AD13 pin I/O control disabled
4
ADC Pin Control 12 — ADPC12 is used to control the pin associated with channel AD12.
ADPC12 0 AD12 pin I/O control enabled
1 AD12 pin I/O control disabled
3
ADC Pin Control 11 — ADPC11 is used to control the pin associated with channel AD11.
ADPC11 0 AD11 pin I/O control enabled
1 AD11 pin I/O control disabled
2
ADC Pin Control 10 — ADPC10 is used to control the pin associated with channel AD10.
ADPC10 0 AD10 pin I/O control enabled
1 AD10 pin I/O control disabled
MC9S08AW60 Data Sheet, Rev 2
246
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
Table 14-10. APCTL2 Register Field Descriptions (continued)
Field
Description
1
ADC Pin Control 9 — ADPC9 is used to control the pin associated with channel AD9.
ADPC9 0 AD9 pin I/O control enabled
1 AD9 pin I/O control disabled
0
ADC Pin Control 8 — ADPC8 is used to control the pin associated with channel AD8.
ADPC8 0 AD8 pin I/O control enabled
1 AD8 pin I/O control disabled
14.4.10 Pin Control 3 Register (APCTL3)
APCTL3 is used to control channels 16–23 of the ADC module.
7
6
5
4
3
2
1
0
R
W
ADPC23
ADPC22
ADPC21
ADPC20
ADPC19
ADPC18
ADPC17
ADPC16
Reset:
0
0
0
0
0
0
0
0
Figure 14-13. Pin Control 3 Register (APCTL3)
Table 14-11. APCTL3 Register Field Descriptions
Description
Field
7
ADC Pin Control 23 — ADPC23 is used to control the pin associated with channel AD23.
ADPC23 0 AD23 pin I/O control enabled
1 AD23 pin I/O control disabled
6
ADC Pin Control 22 — ADPC22 is used to control the pin associated with channel AD22.
ADPC22 0 AD22 pin I/O control enabled
1 AD22 pin I/O control disabled
5
ADC Pin Control 21 — ADPC21 is used to control the pin associated with channel AD21.
ADPC21 0 AD21 pin I/O control enabled
1 AD21 pin I/O control disabled
4
ADC Pin Control 20 — ADPC20 is used to control the pin associated with channel AD20.
ADPC20 0 AD20 pin I/O control enabled
1 AD20 pin I/O control disabled
3
ADC Pin Control 19 — ADPC19 is used to control the pin associated with channel AD19.
ADPC19 0 AD19 pin I/O control enabled
1 AD19 pin I/O control disabled
2
ADC Pin Control 18 — ADPC18 is used to control the pin associated with channel AD18.
ADPC18 0 AD18 pin I/O control enabled
1 AD18 pin I/O control disabled
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
247
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
Table 14-11. APCTL3 Register Field Descriptions (continued)
Field
Description
1
ADC Pin Control 17 — ADPC17 is used to control the pin associated with channel AD17.
ADPC17 0 AD17 pin I/O control enabled
1 AD17 pin I/O control disabled
0
ADC Pin Control 16 — ADPC16 is used to control the pin associated with channel AD16.
ADPC16 0 AD16 pin I/O control enabled
1 AD16 pin I/O control disabled
14.5 Functional Description
The ADC module is disabled during reset or when the ADCH bits are all high. The module is idle when a
conversion has completed and another conversion has not been initiated. When idle, the module is in its
lowest power state.
The ADC can perform an analog-to-digital conversion on any of the software selectable channels. The
selected channel voltage is converted by a successive approximation algorithm into an 11-bit digital result.
In 8-bit mode, the selected channel voltage is converted by a successive approximation algorithm into a
9-bit digital result.
When the conversion is completed, the result is placed in the data registers (ADC1RH and ADC1RL).In
10-bit mode, the result is rounded to 10 bits and placed in ADC1RH and ADC1RL. In 8-bit mode, the
result is rounded to 8 bits and placed in ADC1RL. The conversion complete flag (COCO) is then set and
an interrupt is generated if the conversion complete interrupt has been enabled (AIEN = 1).
The ADC module has the capability of automatically comparing the result of a conversion with the
contents of its compare registers. The compare function is enabled by setting the ACFE bit and operates
in conjunction with any of the conversion modes and configurations.
14.5.1 Clock Select and Divide Control
One of four clock sources can be selected as the clock source for the ADC module. This clock source is
then divided by a configurable value to generate the input clock to the converter (ADCK). The clock is
selected from one of the following sources by means of the ADICLK bits.
•
The bus clock, which is equal to the frequency at which software is executed. This is the default
selection following reset.
•
The bus clock divided by 2. For higher bus clock rates, this allows a maximum divide by 16 of the
bus clock.
•
•
ALTCLK, as defined for this MCU (See module section introduction).
The asynchronous clock (ADACK) – This clock is generated from a clock source within the ADC
module. When selected as the clock source this clock remains active while the MCU is in wait or
stop3 mode and allows conversions in these modes for lower noise operation.
Whichever clock is selected, its frequency must fall within the specified frequency range for ADCK. If the
available clocks are too slow, the ADC will not perform according to specifications. If the available clocks
MC9S08AW60 Data Sheet, Rev 2
248
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
are too fast, then the clock must be divided to the appropriate frequency. This divider is specified by the
ADIV bits and can be divide-by 1, 2, 4, or 8.
14.5.2 Input Select and Pin Control
The pin control registers (APCTL3, APCTL2, and APCTL1) are used to disable the I/O port control of the
pins used as analog inputs.When a pin control register bit is set, the following conditions are forced for the
associated MCU pin:
•
•
The output buffer is forced to its high impedance state.
The input buffer is disabled. A read of the I/O port returns a zero for any pin with its input buffer
disabled.
•
The pullup is disabled.
14.5.3 Hardware Trigger
The ADC module has a selectable asynchronous hardware conversion trigger, ADHWT, that is enabled
when the ADTRG bit is set. This source is not available on all MCUs. Consult the module introduction for
information on the ADHWT source specific to this MCU.
When ADHWT source is available and hardware trigger is enabled (ADTRG=1), a conversion is initiated
on the rising edge of ADHWT. If a conversion is in progress when a rising edge occurs, the rising edge is
ignored. In continuous convert configuration, only the initial rising edge to launch continuous conversions
is observed. The hardware trigger function operates in conjunction with any of the conversion modes and
configurations.
14.5.4 Conversion Control
Conversions can be performed in either 10-bit mode or 8-bit mode as determined by the MODE bits.
Conversions can be initiated by either a software or hardware trigger. In addition, the ADC module can be
configured for low power operation, long sample time, continuous conversion, and automatic compare of
the conversion result to a software determined compare value.
14.5.4.1 Initiating Conversions
A conversion is initiated:
•
Following a write to ADC1SC1 (with ADCH bits not all 1s) if software triggered operation is
selected.
•
•
Following a hardware trigger (ADHWT) event if hardware triggered operation is selected.
Following the transfer of the result to the data registers when continuous conversion is enabled.
If continuous conversions are enabled a new conversion is automatically initiated after the completion of
the current conversion. In software triggered operation, continuous conversions begin after ADC1SC1 is
written and continue until aborted. In hardware triggered operation, continuous conversions begin after a
hardware trigger event and continue until aborted.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
249
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
14.5.4.2 Completing Conversions
A conversion is completed when the result of the conversion is transferred into the data result registers,
ADC1RH and ADC1RL. This is indicated by the setting of COCO. An interrupt is generated if AIEN is
high at the time that COCO is set.
A blocking mechanism prevents a new result from overwriting previous data in ADC1RH and ADC1RL
if the previous data is in the process of being read while in 10-bit MODE (the ADC1RH register has been
read but the ADC1RL register has not). When blocking is active, the data transfer is blocked, COCO is not
set, and the new result is lost. In the case of single conversions with the compare function enabled and the
compare condition false, blocking has no effect and ADC operation is terminated. In all other cases of
operation, when a data transfer is blocked, another conversion is initiated regardless of the state of ADCO
(single or continuous conversions enabled).
If single conversions are enabled, the blocking mechanism could result in several discarded conversions
and excess power consumption. To avoid this issue, the data registers must not be read after initiating a
single conversion until the conversion completes.
14.5.4.3 Aborting Conversions
Any conversion in progress will be aborted when:
•
A write to ADC1SC1 occurs (the current conversion will be aborted and a new conversion will be
initiated, if ADCH are not all 1s).
•
A write to ADC1SC2, ADC1CFG, ADC1CVH, or ADC1CVL occurs. This indicates a mode of
operation change has occurred and the current conversion is therefore invalid.
•
•
The MCU is reset.
The MCU enters stop mode with ADACK not enabled.
When a conversion is aborted, the contents of the data registers, ADC1RH and ADC1RL, are not altered
but continue to be the values transferred after the completion of the last successful conversion. In the case
that the conversion was aborted by a reset, ADC1RH and ADC1RL return to their reset states.
14.5.4.4 Power Control
The ADC module remains in its idle state until a conversion is initiated. If ADACK is selected as the
conversion clock source, the ADACK clock generator is also enabled.
Power consumption when active can be reduced by setting ADLPC. This results in a lower maximum value
for f
(see the electrical specifications).
ADCK
14.5.4.5 Total Conversion Time
The total conversion time depends on the sample time (as determined by ADLSMP), the MCU bus
frequency, the conversion mode (8-bit or 10-bit), and the frequency of the conversion clock (fADCK). After
the module becomes active, sampling of the input begins. ADLSMP is used to select between short and
long sample times.When sampling is complete, the converter is isolated from the input channel and a
successive approximation algorithm is performed to determine the digital value of the analog signal. The
MC9S08AW60 Data Sheet, Rev 2
250
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
result of the conversion is transferred to ADC1RH and ADC1RL upon completion of the conversion
algorithm.
If the bus frequency is less than the f
frequency, precise sample time for continuous conversions
ADCK
cannot be guaranteed when short sample is enabled (ADLSMP=0). If the bus frequency is less than 1/11th
of the f frequency, precise sample time for continuous conversions cannot be guaranteed when long
ADCK
sample is enabled (ADLSMP=1).
The maximum total conversion time for different conditions is summarized in Table 14-12.
Table 14-12. Total Conversion Time vs. Control Conditions
Conversion Type
ADICLK
ADLSMP
Max Total Conversion Time
Single or first continuous 8-bit
Single or first continuous 10-bit
Single or first continuous 8-bit
Single or first continuous 10-bit
Single or first continuous 8-bit
Single or first continuous 10-bit
Single or first continuous 8-bit
Single or first continuous 10-bit
0x, 10
0x, 10
0x, 10
0x, 10
11
0
0
1
1
0
0
1
1
0
20 ADCK cycles + 5 bus clock cycles
23 ADCK cycles + 5 bus clock cycles
40 ADCK cycles + 5 bus clock cycles
43 ADCK cycles + 5 bus clock cycles
5 μs + 20 ADCK + 5 bus clock cycles
5 μs + 23 ADCK + 5 bus clock cycles
5 μs + 40 ADCK + 5 bus clock cycles
5 μs + 43 ADCK + 5 bus clock cycles
17 ADCK cycles
11
11
11
Subsequent continuous 8-bit;
xx
fBUS > fADCK
Subsequent continuous 10-bit;
xx
xx
xx
0
1
1
20 ADCK cycles
37 ADCK cycles
40 ADCK cycles
fBUS > fADCK
Subsequent continuous 8-bit;
fBUS > fADCK/11
Subsequent continuous 10-bit;
fBUS > fADCK/11
The maximum total conversion time is determined by the clock source chosen and the divide ratio selected.
The clock source is selectable by the ADICLK bits, and the divide ratio is specified by the ADIV bits. For
example, in 10-bit mode, with the bus clock selected as the input clock source, the input clock divide-by-1
ratio selected, and a bus frequency of 8 MHz, then the conversion time for a single conversion is:
23 ADCK cyc
8 MHz/1
5 bus cyc
8 MHz
= 3.5 μs
Conversion time =
+
Number of bus cycles = 3.5 μs x 8 MHz = 28 cycles
NOTE
The ADCK frequency must be between f
maximum to meet ADC specifications.
minimum and f
ADCK
ADCK
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
251
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
14.5.5 Automatic Compare Function
The compare function can be configured to check for either an upper limit or lower limit. After the input
is sampled and converted, the result is added to the two’s complement of the compare value (ADC1CVH
and ADC1CVL). When comparing to an upper limit (ACFGT = 1), if the result is greater-than or equal-to
the compare value, COCO is set. When comparing to a lower limit (ACFGT = 0), if the result is less than
the compare value, COCO is set. The value generated by the addition of the conversion result and the two’s
complement of the compare value is transferred to ADC1RH and ADC1RL.
Upon completion of a conversion while the compare function is enabled, if the compare condition is not
true, COCO is not set and no data is transferred to the result registers. An ADC interrupt is generated upon
the setting of COCO if the ADC interrupt is enabled (AIEN = 1).
NOTE
The compare function can be used to monitor the voltage on a channel while
the MCU is in either wait or stop3 mode. The ADC interrupt will wake the
MCU when the compare condition is met.
14.5.6 MCU Wait Mode Operation
The WAIT instruction puts the MCU in a lower power-consumption standby mode from which recovery
is very fast because the clock sources remain active. If a conversion is in progress when the MCU enters
wait mode, it continues until completion. Conversions can be initiated while the MCU is in wait mode by
means of the hardware trigger or if continuous conversions are enabled.
The bus clock, bus clock divided by two, and ADACK are available as conversion clock sources while in
wait mode. The use of ALTCLK as the conversion clock source in wait is dependent on the definition of
ALTCLK for this MCU. Consult the module introduction for information on ALTCLK specific to this
MCU.
A conversion complete event sets the COCO and generates an ADC interrupt to wake the MCU from wait
mode if the ADC interrupt is enabled (AIEN = 1).
14.5.7 MCU Stop3 Mode Operation
The STOP instruction is used to put the MCU in a low power-consumption standby mode during which
most or all clock sources on the MCU are disabled.
14.5.7.1 Stop3 Mode With ADACK Disabled
If the asynchronous clock, ADACK, is not selected as the conversion clock, executing a STOP instruction
aborts the current conversion and places the ADC in its idle state. The contents of ADC1RH and ADC1RL
are unaffected by stop3 mode.After exiting from stop3 mode, a software or hardware trigger is required to
resume conversions.
MC9S08AW60 Data Sheet, Rev 2
252
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
14.5.7.2 Stop3 Mode With ADACK Enabled
If ADACK is selected as the conversion clock, the ADC continues operation during stop3 mode. For
guaranteed ADC operation, the MCU’s voltage regulator must remain active during stop3 mode. Consult
the module introduction for configuration information for this MCU.
If a conversion is in progress when the MCU enters stop3 mode, it continues until completion. Conversions
can be initiated while the MCU is in stop3 mode by means of the hardware trigger or if continuous
conversions are enabled.
A conversion complete event sets the COCO and generates an ADC interrupt to wake the MCU from stop3
mode if the ADC interrupt is enabled (AIEN = 1).
NOTE
It is possible for the ADC module to wake the system from low power stop
and cause the MCU to begin consuming run-level currents without
generating a system level interrupt. To prevent this scenario, software
should ensure that the data transfer blocking mechanism (discussed in
Section 14.5.4.2, “Completing Conversions) is cleared when entering stop3
and continuing ADC conversions.
14.5.8 MCU Stop1 and Stop2 Mode Operation
The ADC module is automatically disabled when the MCU enters either stop1 or stop2 mode. All module
registers contain their reset values following exit from stop1 or stop2. Therefore the module must be
re-enabled and re-configured following exit from stop1 or stop2.
14.6 Initialization Information
This section gives an example which provides some basic direction on how a user would initialize and
configure the ADC module. The user has the flexibility of choosing between configuring the module for
8-bit or 10-bit resolution, single or continuous conversion, and a polled or interrupt approach, among many
other options. Refer to Table 14-6, Table 14-7, and Table 14-8 for information used in this example.
NOTE
Hexadecimal values designated by a preceding 0x, binary values designated
by a preceding %, and decimal values have no preceding character.
14.6.1 ADC Module Initialization Example
14.6.1.1 Initialization Sequence
Before the ADC module can be used to complete conversions, an initialization procedure must be
performed. A typical sequence is as follows:
1. Update the configuration register (ADCCFG) to select the input clock source and the divide ratio
used to generate the internal clock, ADCK. This register is also used for selecting sample time and
low-power configuration.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
253
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
2. Update status and control register 2 (ADCSC2) to select the conversion trigger (hardware or
software) and compare function options, if enabled.
3. Update status and control register 1 (ADCSC1) to select whether conversions will be continuous
or completed only once, and to enable or disable conversion complete interrupts. The input channel
on which conversions will be performed is also selected here.
14.6.1.2 Pseudo — Code Example
In this example, the ADC module will be set up with interrupts enabled to perform a single 10-bit
conversion at low power with a long sample time on input channel 1, where the internal ADCK clock will
be derived from the bus clock divided by 1.
ADCCFG = 0x98 (%10011000)
Bit 7
Bit 6:5 ADIV
Bit 4
ADLPC
1
00
Configures for low power (lowers maximum clock speed)
Sets the ADCK to the input clock ÷ 1
Configures for long sample time
ADLSMP 1
Bit 3:2 MODE
10
Sets mode at 10-bit conversions
Bit 1:0 ADICLK 00
Selects bus clock as input clock source
ADCSC2 = 0x00 (%00000000)
Bit 7
Bit 6
Bit 5
ADACT
ADTRG
ACFE
0
0
0
Flag indicates if a conversion is in progress
Software trigger selected
Compare function disabled
Bit 4
ACFGT
0
Not used in this example
Bit 3:2
Bit 1:0
00
00
Unimplemented or reserved, always reads zero
Reserved for Freescale’s internal use; always write zero
ADCSC1 = 0x41 (%01000001)
Bit 7
Bit 6
Bit 5
COCO
AIEN
ADCO
0
1
0
Read-only flag which is set when a conversion completes
Conversion complete interrupt enabled
One conversion only (continuous conversions disabled)
Bit 4:0 ADCH
00001 Input channel 1 selected as ADC input channel
ADCRH/L = 0xxx
Holds results of conversion. Read high byte (ADCRH) before low byte (ADCRL) so that conversion
data cannot be overwritten with data from the next conversion.
ADCCVH/L = 0xxx
Holds compare value when compare function enabled
APCTL1=0x02
AD1 pin I/O control disabled. All other AD pins remain general purpose I/O pins
APCTL2=0x00
All other AD pins remain general purpose I/O pins
MC9S08AW60 Data Sheet, Rev 2
254
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
RESET
INITIALIZE ADC
ADCCFG = $98
ADCSC2 = $00
ADCSC1 = $41
NO
CHECK
COCO=1?
YES
READ ADCRH
THEN ADCRL TO
CLEAR COCO BIT
CONTINUE
Figure 14-14. Initialization Flowchart for Example
14.7 Application Information
This section contains information for using the ADC module in applications. The ADC has been designed
to be integrated into a microcontroller for use in embedded control applications requiring an A/D
converter.
14.7.1 External Pins and Routing
The following sections discuss the external pins associated with the ADC module and how they should be
used for best results.
14.7.1.1 Analog Supply Pins
The ADC module has analog power and ground supplies (V
and V
) which are available as
DDAD
SSAD
separate pins on some devices. On other devices, V
is shared on the same pin as the MCU digital V ,
SSAD
SS
and on others, both V
and V
are shared with the MCU digital supply pins. In these cases, there
SSAD
DDAD
are separate pads for the analog supplies which are bonded to the same pin as the corresponding digital
supply so that some degree of isolation between the supplies is maintained.
When available on a separate pin, both V
and V
must be connected to the same voltage potential
SSAD
DDAD
as their corresponding MCU digital supply (V and V ) and must be routed carefully for maximum
DD
SS
noise immunity and bypass capacitors placed as near as possible to the package.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
255
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
In cases where separate power supplies are used for analog and digital power, the ground connection
between these supplies must be at the V
pin. This should be the only ground connection between these
SSAD
supplies if possible. The V
pin makes a good single point ground location.
SSAD
14.7.1.2 Analog Reference Pins
In addition to the analog supplies, the ADC module has connections for two reference voltage inputs. The
high reference is V
, which may be shared on the same pin as V
on some devices. The low
REFH
DDAD
reference is V
, which may be shared on the same pin as V
on some devices.
REFL
SSAD
When available on a separate pin, V
may be connected to the same potential as V
, or may be
DDAD
REFH
driven by an external source that is between the minimum V
spec and the V
potential (V
DDAD
DDAD REFH
must never exceed V
). When available on a separate pin, V
must be connected to the same
DDAD
REFL
voltage potential as V
. Both V
and V
must be routed carefully for maximum noise
SSAD
REFH
REFL
immunity and bypass capacitors placed as near as possible to the package.
AC current in the form of current spikes required to supply charge to the capacitor array at each successive
approximation step is drawn through the V
and V
loop. The best external component to meet this
REFH
REFL
current demand is a 0.1 μF capacitor with good high frequency characteristics. This capacitor is connected
between V and V and must be placed as near as possible to the package pins. Resistance in the
REFH
REFL
path is not recommended because the current will cause a voltage drop which could result in conversion
errors. Inductance in this path must be minimum (parasitic only).
14.7.1.3 Analog Input Pins
The external analog inputs are typically shared with digital I/O pins on MCU devices. The pin I/O control
is disabled by setting the appropriate control bit in one of the pin control registers. Conversions can be
performed on inputs without the associated pin control register bit set. It is recommended that the pin
control register bit always be set when using a pin as an analog input. This avoids problems with contention
because the output buffer will be in its high impedance state and the pullup is disabled. Also, the input
buffer draws dc current when its input is not at either V or V . Setting the pin control register bits for
DD
SS
all pins used as analog inputs should be done to achieve lowest operating current.
Empirical data shows that capacitors on the analog inputs improve performance in the presence of noise
or when the source impedance is high. Use of 0.01 μF capacitors with good high-frequency characteristics
is sufficient. These capacitors are not necessary in all cases, but when used they must be placed as near as
possible to the package pins and be referenced to V
.
SSA
For proper conversion, the input voltage must fall between V
and V
. If the input is equal to or
REFH
REFL
exceeds V
, the converter circuit converts the signal to $3FF (full scale 10-bit representation) or $FF
REFH
(full scale 8-bit representation). If the input is equal to or less than V
, the converter circuit converts it
REFL
to $000. Input voltages between V
and V
are straight-line linear conversions. There will be a
REFH
REFL
brief current associated with V
when the sampling capacitor is charging. The input is sampled for
REFL
3.5 cycles of the ADCK source when ADLSMP is low, or 23.5 cycles when ADLSMP is high.
For minimal loss of accuracy due to current injection, pins adjacent to the analog input pins should not be
transitioning during conversions.
MC9S08AW60 Data Sheet, Rev 2
256
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
14.7.2 Sources of Error
Several sources of error exist for A/D conversions. These are discussed in the following sections.
14.7.2.1 Sampling Error
For proper conversions, the input must be sampled long enough to achieve the proper accuracy. Given the
maximum input resistance of approximately 7kΩ and input capacitance of approximately 5.5 pF, sampling
to within 1/4LSB (at 10-bit resolution) can be achieved within the minimum sample window (3.5 cycles @
8 MHz maximum ADCK frequency) provided the resistance of the external analog source (R ) is kept
AS
below 5 kΩ.
Higher source resistances or higher-accuracy sampling is possible by setting ADLSMP (to increase the
sample window to 23.5 cycles) or decreasing ADCK frequency to increase sample time.
14.7.2.2 Pin Leakage Error
Leakage on the I/O pins can cause conversion error if the external analog source resistance (R ) is high.
AS
N
If this error cannot be tolerated by the application, keep R lower than V
/ (2 *I
) for less than
AS
DDAD
LEAK
1/4LSB leakage error (N = 8 in 8-bit mode or 10 in 10-bit mode).
14.7.2.3 Noise-Induced Errors
System noise which occurs during the sample or conversion process can affect the accuracy of the
conversion. The ADC accuracy numbers are guaranteed as specified only if the following conditions are
met:
•
•
•
There is a 0.1 μF low-ESR capacitor from V
There is a 0.1 μF low-ESR capacitor from V
to V
.
REFH
REFL
to V
.
DDAD
SSAD
If inductive isolation is used from the primary supply, an additional 1 μF capacitor is placed from
V
to V
.
DDAD
SSAD
•
•
V
(and V
, if connected) is connected to V at a quiet point in the ground plane.
REFL SS
SSAD
Operate the MCU in wait or stop3 mode before initiating (hardware triggered conversions) or
immediately after initiating (hardware or software triggered conversions) the ADC conversion.
— For software triggered conversions, immediately follow the write to the ADC1SC1 with a
WAIT instruction or STOP instruction.
— For stop3 mode operation, select ADACK as the clock source. Operation in stop3 reduces V
noise but increases effective conversion time due to stop recovery.
DD
•
There is no I/O switching, input or output, on the MCU during the conversion.
There are some situations where external system activity causes radiated or conducted noise emissions or
excessive V noise is coupled into the ADC. In these situations, or when the MCU cannot be placed in
DD
wait or stop3 or I/O activity cannot be halted, these recommended actions may reduce the effect of noise
on the accuracy:
•
Place a 0.01 μF capacitor (C ) on the selected input channel to V
or V
(this will
SSAD
AS
REFL
improve noise issues but will affect sample rate based on the external analog source resistance).
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
257
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
•
•
Average the result by converting the analog input many times in succession and dividing the sum
of the results. Four samples are required to eliminate the effect of a 1LSB, one-time error.
Reduce the effect of synchronous noise by operating off the asynchronous clock (ADACK) and
averaging. Noise that is synchronous to ADCK cannot be averaged out.
14.7.2.4 Code Width and Quantization Error
The ADC quantizes the ideal straight-line transfer function into 1024 steps (in 10-bit mode). Each step
ideally has the same height (1 code) and width. The width is defined as the delta between the transition
points to one code and the next. The ideal code width for an N bit converter (in this case N can be 8 or 10),
defined as 1LSB, is:
N
1LSB = (V
- V
) / 2
Eqn. 14-2
REFH
REFL
There is an inherent quantization error due to the digitization of the result. For 8-bit or 10-bit conversions
the code will transition when the voltage is at the midpoint between the points where the straight line
transfer function is exactly represented by the actual transfer function. Therefore, the quantization error
will be 1/2LSB in 8- or 10-bit mode. As a consequence, however, the code width of the first ($000)
conversion is only 1/2LSB and the code width of the last ($FF or $3FF) is 1.5LSB.
14.7.2.5 Linearity Errors
The ADC may also exhibit non-linearity of several forms. Every effort has been made to reduce these
errors but the system should be aware of them because they affect overall accuracy. These errors are:
•
Zero-scale error (E ) (sometimes called offset) — This error is defined as the difference between
ZS
the actual code width of the first conversion and the ideal code width (1/2LSB). Note, if the first
conversion is $001, then the difference between the actual $001 code width and its ideal (1LSB) is
used.
•
Full-scale error (E ) — This error is defined as the difference between the actual code width of
FS
the last conversion and the ideal code width (1.5LSB). Note, if the last conversion is $3FE, then the
difference between the actual $3FE code width and its ideal (1LSB) is used.
•
•
Differential non-linearity (DNL) — This error is defined as the worst-case difference between the
actual code width and the ideal code width for all conversions.
Integral non-linearity (INL) — This error is defined as the highest-value the (absolute value of the)
running sum of DNL achieves. More simply, this is the worst-case difference of the actual
transition voltage to a given code and its corresponding ideal transition voltage, for all codes.
•
Total unadjusted error (TUE) — This error is defined as the difference between the actual transfer
function and the ideal straight-line transfer function, and therefore includes all forms of error.
14.7.2.6 Code Jitter, Non-Monotonicity and Missing Codes
Analog-to-digital converters are susceptible to three special forms of error. These are code jitter,
non-monotonicity, and missing codes.
Code jitter is when, at certain points, a given input voltage converts to one of two values when sampled
repeatedly. Ideally, when the input voltage is infinitesimally smaller than the transition voltage, the
MC9S08AW60 Data Sheet, Rev 2
258
Freescale Semiconductor
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
converter yields the lower code (and vice-versa). However, even very small amounts of system noise can
cause the converter to be indeterminate (between two codes) for a range of input voltages around the
transition voltage. This range is normally around 1/2LSB and will increase with noise. This error may be
reduced by repeatedly sampling the input and averaging the result. Additionally the techniques discussed
in Section 14.7.2.3 will reduce this error.
Non-monotonicity is defined as when, except for code jitter, the converter converts to a lower code for a
higher input voltage. Missing codes are those values which are never converted for any input value.
In 8-bit or 10-bit mode, the ADC is guaranteed to be monotonic and to have no missing codes.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
259
Chapter 14 Analog-to-Digital Converter (S08ADC10V1)
MC9S08AW60 Data Sheet, Rev 2
260
Freescale Semiconductor
Chapter 15
Development Support
15.1 Introduction
Development support systems in the HCS08 include the background debug controller (BDC) and the
on-chip debug module (DBG). The BDC provides a single-wire debug interface to the target MCU that
provides a convenient interface for programming the on-chip FLASH and other nonvolatile memories. The
BDC is also the primary debug interface for development and allows non-intrusive access to memory data
and traditional debug features such as CPU register modify, breakpoints, and single instruction trace
commands.
In the HCS08 family, address and data bus signals are not available on external pins (not even in test
modes). Debug is done through commands fed into the target MCU via the single-wire background debug
interface. The debug module provides a means to selectively trigger and capture bus information so an
external development system can reconstruct what happened inside the MCU on a cycle-by-cycle basis
without having external access to the address and data signals.
The alternate BDC clock source for MC9S08AW60 Series is the ICGLCLK. See Chapter 8, “Internal
Clock Generator (S08ICGV4)” for more information about ICGCLK and how to select clock sources.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
261
Chapter 15 Development Support
15.1.1 Features
Features of the BDC module include:
•
•
•
•
•
•
•
•
•
•
Single pin for mode selection and background communications
BDC registers are not located in the memory map
SYNC command to determine target communications rate
Non-intrusive commands for memory access
Active background mode commands for CPU register access
GO and TRACE1 commands
BACKGROUND command can wake CPU from stop or wait modes
One hardware address breakpoint built into BDC
Oscillator runs in stop mode, if BDC enabled
COP watchdog disabled while in active background mode
Features of the ICE system include:
•
•
Two trigger comparators: Two address + read/write (R/W) or one full address + data + R/W
Flexible 8-word by 16-bit FIFO (first-in, first-out) buffer for capture information:
— Change-of-flow addresses or
— Event-only data
•
•
Two types of breakpoints:
— Tag breakpoints for instruction opcodes
— Force breakpoints for any address access
Nine trigger modes:
— Basic: A-only, A OR B
— Sequence: A then B
— Full: A AND B data, A AND NOT B data
— Event (store data): Event-only B, A then event-only B
— Range: Inside range (A ≤ address ≤ B), outside range (address < A or address > B)
15.2 Background Debug Controller (BDC)
All MCUs in the HCS08 family contain a single-wire background debug interface that supports in-circuit
programming of on-chip nonvolatile memory and sophisticated non-intrusive debug capabilities. Unlike
debug interfaces on earlier 8-bit MCUs, this system does not interfere with normal application resources.
It does not use any user memory or locations in the memory map and does not share any on-chip
peripherals.
BDC commands are divided into two groups:
•
Active background mode commands require that the target MCU is in active background mode (the
user program is not running). Active background mode commands allow the CPU registers to be
read or written, and allow the user to trace one user instruction at a time, or GO to the user program
from active background mode.
MC9S08AW60 Data Sheet, Rev 2
262
Freescale Semiconductor
Chapter 15 Development Support
•
Non-intrusive commands can be executed at any time even while the user’s program is running.
Non-intrusive commands allow a user to read or write MCU memory locations or access status and
control registers within the background debug controller.
Typically, a relatively simple interface pod is used to translate commands from a host computer into
commands for the custom serial interface to the single-wire background debug system. Depending on the
development tool vendor, this interface pod may use a standard RS-232 serial port, a parallel printer port,
or some other type of communications such as a universal serial bus (USB) to communicate between the
host PC and the pod. The pod typically connects to the target system with ground, the BKGD pin, RESET,
and sometimes V . An open-drain connection to reset allows the host to force a target system reset,
DD
which is useful to regain control of a lost target system or to control startup of a target system before the
on-chip nonvolatile memory has been programmed. Sometimes V can be used to allow the pod to use
DD
power from the target system to avoid the need for a separate power supply. However, if the pod is powered
separately, it can be connected to a running target system without forcing a target system reset or otherwise
disturbing the running application program.
2
GND
BKGD
1
NO CONNECT 3
NO CONNECT 5
4 RESET
6 V
DD
Figure 15-1. BDM Tool Connector
15.2.1 BKGD Pin Description
BKGD is the single-wire background debug interface pin. The primary function of this pin is for
bidirectional serial communication of active background mode commands and data. During reset, this pin
is used to select between starting in active background mode or starting the user’s application program.
This pin is also used to request a timed sync response pulse to allow a host development tool to determine
the correct clock frequency for background debug serial communications.
BDC serial communications use a custom serial protocol first introduced on the M68HC12 family of
microcontrollers. This protocol assumes the host knows the communication clock rate that is determined
by the target BDC clock rate. All communication is initiated and controlled by the host that drives a
high-to-low edge to signal the beginning of each bit time. Commands and data are sent most significant bit
first (MSB first). For a detailed description of the communications protocol, refer to Section 15.2.2,
“Communication Details.”
If a host is attempting to communicate with a target MCU that has an unknown BDC clock rate, a SYNC
command may be sent to the target MCU to request a timed sync response signal from which the host can
determine the correct communication speed.
BKGD is a pseudo-open-drain pin and there is an on-chip pullup so no external pullup resistor is required.
Unlike typical open-drain pins, the external RC time constant on this pin, which is influenced by external
capacitance, plays almost no role in signal rise time. The custom protocol provides for brief, actively
driven speedup pulses to force rapid rise times on this pin without risking harmful drive level conflicts.
Refer to Section 15.2.2, “Communication Details,” for more detail.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
263
Chapter 15 Development Support
When no debugger pod is connected to the 6-pin BDM interface connector, the internal pullup on BKGD
chooses normal operating mode. When a debug pod is connected to BKGD it is possible to force the MCU
into active background mode after reset. The specific conditions for forcing active background depend
upon the HCS08 derivative (refer to the introduction to this Development Support section). It is not
necessary to reset the target MCU to communicate with it through the background debug interface.
15.2.2 Communication Details
The BDC serial interface requires the external controller to generate a falling edge on the BKGD pin to
indicate the start of each bit time. The external controller provides this falling edge whether data is
transmitted or received.
BKGD is a pseudo-open-drain pin that can be driven either by an external controller or by the MCU. Data
is transferred MSB first at 16 BDC clock cycles per bit (nominal speed). The interface times out if
512 BDC clock cycles occur between falling edges from the host. Any BDC command that was in progress
when this timeout occurs is aborted without affecting the memory or operating mode of the target MCU
system.
The custom serial protocol requires the debug pod to know the target BDC communication clock speed.
The clock switch (CLKSW) control bit in the BDC status and control register allows the user to select the
BDC clock source. The BDC clock source can either be the bus or the alternate BDC clock source.
The BKGD pin can receive a high or low level or transmit a high or low level. The following diagrams
show timing for each of these cases. Interface timing is synchronous to clocks in the target BDC, but
asynchronous to the external host. The internal BDC clock signal is shown for reference in counting cycles.
MC9S08AW60 Data Sheet, Rev 2
264
Freescale Semiconductor
Chapter 15 Development Support
Figure 15-2 shows an external host transmitting a logic 1 or 0 to the BKGD pin of a target HCS08 MCU.
The host is asynchronous to the target so there is a 0-to-1 cycle delay from the host-generated falling edge
to where the target perceives the beginning of the bit time. Ten target BDC clock cycles later, the target
senses the bit level on the BKGD pin. Typically, the host actively drives the pseudo-open-drain BKGD pin
during host-to-target transmissions to speed up rising edges. Because the target does not drive the BKGD
pin during the host-to-target transmission period, there is no need to treat the line as an open-drain signal
during this period.
BDC CLOCK
(TARGET MCU)
HOST
TRANSMIT 1
HOST
TRANSMIT 0
10 CYCLES
EARLIEST START
OF NEXT BIT
SYNCHRONIZATION
UNCERTAINTY
TARGET SENSES BIT LEVEL
PERCEIVED START
OF BIT TIME
Figure 15-2. BDC Host-to-Target Serial Bit Timing
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
265
Chapter 15 Development Support
Figure 15-3 shows the host receiving a logic 1 from the target HCS08 MCU. Because the host is
asynchronous to the target MCU, there is a 0-to-1 cycle delay from the host-generated falling edge on
BKGD to the perceived start of the bit time in the target MCU. The host holds the BKGD pin low long
enough for the target to recognize it (at least two target BDC cycles). The host must release the low drive
before the target MCU drives a brief active-high speedup pulse seven cycles after the perceived start of the
bit time. The host should sample the bit level about 10 cycles after it started the bit time.
BDC CLOCK
(TARGET MCU)
HOST DRIVE
HIGH-IMPEDANCE
TO BKGD PIN
TARGET MCU
SPEEDUP PULSE
HIGH-IMPEDANCE
HIGH-IMPEDANCE
PERCEIVED START
OF BIT TIME
R-C RISE
BKGD PIN
10 CYCLES
10 CYCLES
EARLIEST START
OF NEXT BIT
HOST SAMPLES BKGD PIN
Figure 15-3. BDC Target-to-Host Serial Bit Timing (Logic 1)
MC9S08AW60 Data Sheet, Rev 2
266
Freescale Semiconductor
Chapter 15 Development Support
Figure 15-4 shows the host receiving a logic 0 from the target HCS08 MCU. Because the host is
asynchronous to the target MCU, there is a 0-to-1 cycle delay from the host-generated falling edge on
BKGD to the start of the bit time as perceived by the target MCU. The host initiates the bit time but the
target HCS08 finishes it. Because the target wants the host to receive a logic 0, it drives the BKGD pin low
for 13 BDC clock cycles, then briefly drives it high to speed up the rising edge. The host samples the bit
level about 10 cycles after starting the bit time.
BDC CLOCK
(TARGET MCU)
HOST DRIVE
TO BKGD PIN
HIGH-IMPEDANCE
SPEEDUP
PULSE
TARGET MCU
DRIVE AND
SPEED-UP PULSE
PERCEIVED START
OF BIT TIME
BKGD PIN
10 CYCLES
10 CYCLES
EARLIEST START
OF NEXT BIT
HOST SAMPLES BKGD PIN
Figure 15-4. BDM Target-to-Host Serial Bit Timing (Logic 0)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
267
Chapter 15 Development Support
15.2.3 BDC Commands
BDC commands are sent serially from a host computer to the BKGD pin of the target HCS08 MCU. All
commands and data are sent MSB-first using a custom BDC communications protocol. Active background
mode commands require that the target MCU is currently in the active background mode while
non-intrusive commands may be issued at any time whether the target MCU is in active background mode
or running a user application program.
Table 15-1 shows all HCS08 BDC commands, a shorthand description of their coding structure, and the
meaning of each command.
Coding Structure Nomenclature
This nomenclature is used in Table 15-1 to describe the coding structure of the BDC commands.
Commands begin with an 8-bit hexadecimal command code in the host-to-target
direction (most significant bit first)
/
d
= separates parts of the command
=
=
=
=
=
=
=
=
=
delay 16 target BDC clock cycles
a 16-bit address in the host-to-target direction
AAAA
RD
8 bits of read data in the target-to-host direction
8 bits of write data in the host-to-target direction
16 bits of read data in the target-to-host direction
16 bits of write data in the host-to-target direction
the contents of BDCSCR in the target-to-host direction (STATUS)
8 bits of write data for BDCSCR in the host-to-target direction (CONTROL)
WD
RD16
WD16
SS
CC
RBKP
16 bits of read data in the target-to-host direction (from BDCBKPT breakpoint
register)
WBKP
=
16 bits of write data in the host-to-target direction (for BDCBKPT breakpoint register)
MC9S08AW60 Data Sheet, Rev 2
268
Freescale Semiconductor
Chapter 15 Development Support
Description
Table 15-1. BDC Command Summary
Command
Mnemonic
Active BDM/
Coding
Non-intrusive
Structure
Request a timed reference pulse to determine
target BDC communication speed
n/a1
D5/d
D6/d
90/d
SYNC
Non-intrusive
Enable acknowledge protocol. Refer to
Freescale document order no. HCS08RMv1/D.
ACK_ENABLE
ACK_DISABLE
BACKGROUND
Non-intrusive
Non-intrusive
Non-intrusive
Disable acknowledge protocol. Refer to
Freescale document order no. HCS08RMv1/D.
Enter active background mode if enabled
(ignore if ENBDM bit equals 0)
READ_STATUS
WRITE_CONTROL
READ_BYTE
Non-intrusive
Non-intrusive
Non-intrusive
Non-intrusive
E4/SS
C4/CC
Read BDC status from BDCSCR
Write BDC controls in BDCSCR
Read a byte from target memory
Read a byte and report status
E0/AAAA/d/RD
READ_BYTE_WS
E1/AAAA/d/SS/RD
Re-read byte from address just read and
report status
READ_LAST
Non-intrusive
E8/SS/RD
WRITE_BYTE
WRITE_BYTE_WS
READ_BKPT
Non-intrusive
Non-intrusive
Non-intrusive
Non-intrusive
C0/AAAA/WD/d
C1/AAAA/WD/d/SS
E2/RBKP
Write a byte to target memory
Write a byte and report status
Read BDCBKPT breakpoint register
Write BDCBKPT breakpoint register
WRITE_BKPT
C2/WBKP
Go to execute the user application program
starting at the address currently in the PC
GO
Active BDM
Active BDM
Active BDM
08/d
10/d
18/d
Trace 1 user instruction at the address in the
PC, then return to active background mode
TRACE1
TAGGO
Same as GO but enable external tagging
(HCS08 devices have no external tagging pin)
READ_A
Active BDM
Active BDM
Active BDM
Active BDM
Active BDM
68/d/RD
Read accumulator (A)
READ_CCR
READ_PC
READ_HX
READ_SP
69/d/RD
Read condition code register (CCR)
Read program counter (PC)
Read H and X register pair (H:X)
Read stack pointer (SP)
6B/d/RD16
6C/d/RD16
6F/d/RD16
Increment H:X by one then read memory byte
located at H:X
READ_NEXT
Active BDM
Active BDM
70/d/RD
Increment H:X by one then read memory byte
located at H:X. Report status and data.
READ_NEXT_WS
71/d/SS/RD
WRITE_A
Active BDM
Active BDM
Active BDM
Active BDM
Active BDM
48/WD/d
Write accumulator (A)
WRITE_CCR
WRITE_PC
WRITE_HX
WRITE_SP
49/WD/d
Write condition code register (CCR)
Write program counter (PC)
Write H and X register pair (H:X)
Write stack pointer (SP)
4B/WD16/d
4C/WD16/d
4F/WD16/d
Increment H:X by one, then write memory byte
located at H:X
WRITE_NEXT
Active BDM
Active BDM
50/WD/d
Increment H:X by one, then write memory byte
located at H:X. Also report status.
WRITE_NEXT_WS
51/WD/d/SS
1
The SYNC command is a special operation that does not have a command code.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
269
Chapter 15 Development Support
The SYNC command is unlike other BDC commands because the host does not necessarily know the
correct communications speed to use for BDC communications until after it has analyzed the response to
the SYNC command.
To issue a SYNC command, the host:
•
Drives the BKGD pin low for at least 128 cycles of the slowest possible BDC clock (The slowest
clock is normally the reference oscillator/64 or the self-clocked rate/64.)
•
Drives BKGD high for a brief speedup pulse to get a fast rise time (This speedup pulse is typically
one cycle of the fastest clock in the system.)
•
•
Removes all drive to the BKGD pin so it reverts to high impedance
Monitors the BKGD pin for the sync response pulse
The target, upon detecting the SYNC request from the host (which is a much longer low time than would
ever occur during normal BDC communications):
•
•
•
•
•
Waits for BKGD to return to a logic high
Delays 16 cycles to allow the host to stop driving the high speedup pulse
Drives BKGD low for 128 BDC clock cycles
Drives a 1-cycle high speedup pulse to force a fast rise time on BKGD
Removes all drive to the BKGD pin so it reverts to high impedance
The host measures the low time of this 128-cycle sync response pulse and determines the correct speed for
subsequent BDC communications. Typically, the host can determine the correct communication speed
within a few percent of the actual target speed and the communication protocol can easily tolerate speed
errors of several percent.
15.2.4 BDC Hardware Breakpoint
The BDC includes one relatively simple hardware breakpoint that compares the CPU address bus to a
16-bit match value in the BDCBKPT register. This breakpoint can generate a forced breakpoint or a tagged
breakpoint. A forced breakpoint causes the CPU to enter active background mode at the first instruction
boundary following any access to the breakpoint address. The tagged breakpoint causes the instruction
opcode at the breakpoint address to be tagged so that the CPU will enter active background mode rather
than executing that instruction if and when it reaches the end of the instruction queue. This implies that
tagged breakpoints can only be placed at the address of an instruction opcode while forced breakpoints can
be set at any address.
The breakpoint enable (BKPTEN) control bit in the BDC status and control register (BDCSCR) is used to
enable the breakpoint logic (BKPTEN = 1). When BKPTEN = 0, its default value after reset, the
breakpoint logic is disabled and no BDC breakpoints are requested regardless of the values in other BDC
breakpoint registers and control bits. The force/tag select (FTS) control bit in BDCSCR is used to select
forced (FTS = 1) or tagged (FTS = 0) type breakpoints.
The on-chip debug module (DBG) includes circuitry for two additional hardware breakpoints that are more
flexible than the simple breakpoint in the BDC module.
MC9S08AW60 Data Sheet, Rev 2
270
Freescale Semiconductor
Chapter 15 Development Support
15.3 On-Chip Debug System (DBG)
Because HCS08 devices do not have external address and data buses, the most important functions of an
in-circuit emulator have been built onto the chip with the MCU. The debug system consists of an 8-stage
FIFO that can store address or data bus information, and a flexible trigger system to decide when to capture
bus information and what information to capture. The system relies on the single-wire background debug
system to access debug control registers and to read results out of the eight stage FIFO.
The debug module includes control and status registers that are accessible in the user’s memory map.
These registers are located in the high register space to avoid using valuable direct page memory space.
Most of the debug module’s functions are used during development, and user programs rarely access any
of the control and status registers for the debug module. The one exception is that the debug system can
provide the means to implement a form of ROM patching. This topic is discussed in greater detail in
Section 15.3.6, “Hardware Breakpoints.”
15.3.1 Comparators A and B
Two 16-bit comparators (A and B) can optionally be qualified with the R/W signal and an opcode tracking
circuit. Separate control bits allow you to ignore R/W for each comparator. The opcode tracking circuitry
optionally allows you to specify that a trigger will occur only if the opcode at the specified address is
actually executed as opposed to only being read from memory into the instruction queue. The comparators
are also capable of magnitude comparisons to support the inside range and outside range trigger modes.
Comparators are disabled temporarily during all BDC accesses.
The A comparator is always associated with the 16-bit CPU address. The B comparator compares to the
CPU address or the 8-bit CPU data bus, depending on the trigger mode selected. Because the CPU data
bus is separated into a read data bus and a write data bus, the RWAEN and RWA control bits have an
additional purpose, in full address plus data comparisons they are used to decide which of these buses to
use in the comparator B data bus comparisons. If RWAEN = 1 (enabled) and RWA = 0 (write), the CPU’s
write data bus is used. Otherwise, the CPU’s read data bus is used.
The currently selected trigger mode determines what the debugger logic does when a comparator detects
a qualified match condition. A match can cause:
•
•
•
•
Generation of a breakpoint to the CPU
Storage of data bus values into the FIFO
Starting to store change-of-flow addresses into the FIFO (begin type trace)
Stopping the storage of change-of-flow addresses into the FIFO (end type trace)
15.3.2 Bus Capture Information and FIFO Operation
The usual way to use the FIFO is to setup the trigger mode and other control options, then arm the
debugger. When the FIFO has filled or the debugger has stopped storing data into the FIFO, you would
read the information out of it in the order it was stored into the FIFO. Status bits indicate the number of
words of valid information that are in the FIFO as data is stored into it. If a trace run is manually halted by
writing 0 to ARM before the FIFO is full (CNT = 1:0:0:0), the information is shifted by one position and
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
271
Chapter 15 Development Support
the host must perform ((8 – CNT) – 1) dummy reads of the FIFO to advance it to the first significant entry
in the FIFO.
In most trigger modes, the information stored in the FIFO consists of 16-bit change-of-flow addresses. In
these cases, read DBGFH then DBGFL to get one coherent word of information out of the FIFO. Reading
DBGFL (the low-order byte of the FIFO data port) causes the FIFO to shift so the next word of information
is available at the FIFO data port. In the event-only trigger modes (see Section 15.3.5, “Trigger Modes”),
8-bit data information is stored into the FIFO. In these cases, the high-order half of the FIFO (DBGFH) is
not used and data is read out of the FIFO by simply reading DBGFL. Each time DBGFL is read, the FIFO
is shifted so the next data value is available through the FIFO data port at DBGFL.
In trigger modes where the FIFO is storing change-of-flow addresses, there is a delay between CPU
addresses and the input side of the FIFO. Because of this delay, if the trigger event itself is a change-of-flow
address or a change-of-flow address appears during the next two bus cycles after a trigger event starts the
FIFO, it will not be saved into the FIFO. In the case of an end-trace, if the trigger event is a change-of-flow,
it will be saved as the last change-of-flow entry for that debug run.
The FIFO can also be used to generate a profile of executed instruction addresses when the debugger is not
armed. When ARM = 0, reading DBGFL causes the address of the most-recently fetched opcode to be
saved in the FIFO. To use the profiling feature, a host debugger would read addresses out of the FIFO by
reading DBGFH then DBGFL at regular periodic intervals. The first eight values would be discarded
because they correspond to the eight DBGFL reads needed to initially fill the FIFO. Additional periodic
reads of DBGFH and DBGFL return delayed information about executed instructions so the host debugger
can develop a profile of executed instruction addresses.
15.3.3 Change-of-Flow Information
To minimize the amount of information stored in the FIFO, only information related to instructions that
cause a change to the normal sequential execution of instructions is stored. With knowledge of the source
and object code program stored in the target system, an external debugger system can reconstruct the path
of execution through many instructions from the change-of-flow information stored in the FIFO.
For conditional branch instructions where the branch is taken (branch condition was true), the source
address is stored (the address of the conditional branch opcode). Because BRA and BRN instructions are
not conditional, these events do not cause change-of-flow information to be stored in the FIFO.
Indirect JMP and JSR instructions use the current contents of the H:X index register pair to determine the
destination address, so the debug system stores the run-time destination address for any indirect JMP or
JSR. For interrupts, RTI, or RTS, the destination address is stored in the FIFO as change-of-flow
information.
15.3.4 Tag vs. Force Breakpoints and Triggers
Tagging is a term that refers to identifying an instruction opcode as it is fetched into the instruction queue,
but not taking any other action until and unless that instruction is actually executed by the CPU. This
distinction is important because any change-of-flow from a jump, branch, subroutine call, or interrupt
causes some instructions that have been fetched into the instruction queue to be thrown away without being
executed.
MC9S08AW60 Data Sheet, Rev 2
272
Freescale Semiconductor
Chapter 15 Development Support
A force-type breakpoint waits for the current instruction to finish and then acts upon the breakpoint
request. The usual action in response to a breakpoint is to go to active background mode rather than
continuing to the next instruction in the user application program.
The tag vs. force terminology is used in two contexts within the debug module. The first context refers to
breakpoint requests from the debug module to the CPU. The second refers to match signals from the
comparators to the debugger control logic. When a tag-type break request is sent to the CPU, a signal is
entered into the instruction queue along with the opcode so that if/when this opcode ever executes, the CPU
will effectively replace the tagged opcode with a BGND opcode so the CPU goes to active background
mode rather than executing the tagged instruction. When the TRGSEL control bit in the DBGT register is
set to select tag-type operation, the output from comparator A or B is qualified by a block of logic in the
debug module that tracks opcodes and only produces a trigger to the debugger if the opcode at the compare
address is actually executed. There is separate opcode tracking logic for each comparator so more than one
compare event can be tracked through the instruction queue at a time.
15.3.5 Trigger Modes
The trigger mode controls the overall behavior of a debug run. The 4-bit TRG field in the DBGT register
selects one of nine trigger modes. When TRGSEL = 1 in the DBGT register, the output of the comparator
must propagate through an opcode tracking circuit before triggering FIFO actions. The BEGIN bit in
DBGT chooses whether the FIFO begins storing data when the qualified trigger is detected (begin trace),
or the FIFO stores data in a circular fashion from the time it is armed until the qualified trigger is detected
(end trigger).
A debug run is started by writing a 1 to the ARM bit in the DBGC register, which sets the ARMF flag and
clears the AF and BF flags and the CNT bits in DBGS. A begin-trace debug run ends when the FIFO gets
full. An end-trace run ends when the selected trigger event occurs. Any debug run can be stopped manually
by writing a 0 to ARM or DBGEN in DBGC.
In all trigger modes except event-only modes, the FIFO stores change-of-flow addresses. In event-only
trigger modes, the FIFO stores data in the low-order eight bits of the FIFO.
The BEGIN control bit is ignored in event-only trigger modes and all such debug runs are begin type
traces. When TRGSEL = 1 to select opcode fetch triggers, it is not necessary to use R/W in comparisons
because opcode tags would only apply to opcode fetches that are always read cycles. It would also be
unusual to specify TRGSEL = 1 while using a full mode trigger because the opcode value is normally
known at a particular address.
The following trigger mode descriptions only state the primary comparator conditions that lead to a trigger.
Either comparator can usually be further qualified with R/W by setting RWAEN (RWBEN) and the
corresponding RWA (RWB) value to be matched against R/W. The signal from the comparator with
optional R/W qualification is used to request a CPU breakpoint if BRKEN = 1 and TAG determines
whether the CPU request will be a tag request or a force request.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
273
Chapter 15 Development Support
A-Only — Trigger when the address matches the value in comparator A
A OR B — Trigger when the address matches either the value in comparator A or the value in
comparator B
A Then B — Trigger when the address matches the value in comparator B but only after the address for
another cycle matched the value in comparator A. There can be any number of cycles after the A match
and before the B match.
A AND B Data (Full Mode) — This is called a full mode because address, data, and R/W (optionally)
must match within the same bus cycle to cause a trigger event. Comparator A checks address, the low byte
of comparator B checks data, and R/W is checked against RWA if RWAEN = 1. The high-order half of
comparator B is not used.
In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN = TAG = 1), but if you
do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the
CPU breakpoint is issued when the comparator A address matches.
A AND NOT B Data (Full Mode) — Address must match comparator A, data must not match the low
half of comparator B, and R/W must match RWA if RWAEN = 1. All three conditions must be met within
the same bus cycle to cause a trigger.
In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN = TAG = 1), but if you
do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the
CPU breakpoint is issued when the comparator A address matches.
Event-Only B (Store Data) — Trigger events occur each time the address matches the value in
comparator B. Trigger events cause the data to be captured into the FIFO. The debug run ends when the
FIFO becomes full.
A Then Event-Only B (Store Data) — After the address has matched the value in comparator A, a trigger
event occurs each time the address matches the value in comparator B. Trigger events cause the data to be
captured into the FIFO. The debug run ends when the FIFO becomes full.
Inside Range (A ≤ Address ≤ B) — A trigger occurs when the address is greater than or equal to the value
in comparator A and less than or equal to the value in comparator B at the same time.
Outside Range (Address < A or Address > B) — A trigger occurs when the address is either less than
the value in comparator A or greater than the value in comparator B.
MC9S08AW60 Data Sheet, Rev 2
274
Freescale Semiconductor
Chapter 15 Development Support
15.3.6 Hardware Breakpoints
The BRKEN control bit in the DBGC register may be set to 1 to allow any of the trigger conditions
described in Section 15.3.5, “Trigger Modes,” to be used to generate a hardware breakpoint request to the
CPU. TAG in DBGC controls whether the breakpoint request will be treated as a tag-type breakpoint or a
force-type breakpoint. A tag breakpoint causes the current opcode to be marked as it enters the instruction
queue. If a tagged opcode reaches the end of the pipe, the CPU executes a BGND instruction to go to active
background mode rather than executing the tagged opcode. A force-type breakpoint causes the CPU to
finish the current instruction and then go to active background mode.
If the background mode has not been enabled (ENBDM = 1) by a serial WRITE_CONTROL command
through the BKGD pin, the CPU will execute an SWI instruction instead of going to active background
mode.
15.4 Register Definition
This section contains the descriptions of the BDC and DBG registers and control bits.
Refer to the high-page register summary in the device overview chapter of this data sheet for the absolute
address assignments for all DBG registers. This section refers to registers and control bits only by their
names. A Freescale-provided equate or header file is used to translate these names into the appropriate
absolute addresses.
15.4.1 BDC Registers and Control Bits
The BDC has two registers:
•
The BDC status and control register (BDCSCR) is an 8-bit register containing control and status
bits for the background debug controller.
•
The BDC breakpoint match register (BDCBKPT) holds a 16-bit breakpoint match address.
These registers are accessed with dedicated serial BDC commands and are not located in the memory
space of the target MCU (so they do not have addresses and cannot be accessed by user programs).
Some of the bits in the BDCSCR have write limitations; otherwise, these registers may be read or written
at any time. For example, the ENBDM control bit may not be written while the MCU is in active
background mode. (This prevents the ambiguous condition of the control bit forbidding active background
mode while the MCU is already in active background mode.) Also, the four status bits (BDMACT, WS,
WSF, and DVF) are read-only status indicators and can never be written by the WRITE_CONTROL serial
BDC command. The clock switch (CLKSW) control bit may be read or written at any time.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
275
Chapter 15 Development Support
15.4.1.1 BDC Status and Control Register (BDCSCR)
This register can be read or written by serial BDC commands (READ_STATUS and WRITE_CONTROL)
but is not accessible to user programs because it is not located in the normal memory map of the MCU.
7
6
5
4
3
2
1
0
R
BDMACT
WS
WSF
DVF
ENBDM
BKPTEN
FTS
CLKSW
W
Normal
Reset
0
1
0
1
0
0
0
0
0
1
0
0
0
0
0
0
Reset in
Active BDM:
= Unimplemented or Reserved
Figure 15-5. BDC Status and Control Register (BDCSCR)
Table 15-2. BDCSCR Register Field Descriptions
Description
Field
7
Enable BDM (Permit Active Background Mode) — Typically, this bit is written to 1 by the debug host shortly
after the beginning of a debug session or whenever the debug host resets the target and remains 1 until a normal
reset clears it.
ENBDM
0 BDM cannot be made active (non-intrusive commands still allowed)
1 BDM can be made active to allow active background mode commands
6
Background Mode Active Status — This is a read-only status bit.
BDMACT 0 BDM not active (user application program running)
1 BDM active and waiting for serial commands
5
BDC Breakpoint Enable — If this bit is clear, the BDC breakpoint is disabled and the FTS (force tag select)
control bit and BDCBKPT match register are ignored.
0 BDC breakpoint disabled
BKPTEN
1 BDC breakpoint enabled
4
FTS
Force/Tag Select — When FTS = 1, a breakpoint is requested whenever the CPU address bus matches the
BDCBKPT match register. When FTS = 0, a match between the CPU address bus and the BDCBKPT register
causes the fetched opcode to be tagged. If this tagged opcode ever reaches the end of the instruction queue,
the CPU enters active background mode rather than executing the tagged opcode.
0 Tag opcode at breakpoint address and enter active background mode if CPU attempts to execute that
instruction
1 Breakpoint match forces active background mode at next instruction boundary (address need not be an
opcode)
3
Select Source for BDC Communications Clock — CLKSW defaults to 0, which selects the alternate BDC
CLKSW
clock source.
0 Alternate BDC clock source
1 MCU bus clock
MC9S08AW60 Data Sheet, Rev 2
276
Freescale Semiconductor
Chapter 15 Development Support
Table 15-2. BDCSCR Register Field Descriptions (continued)
Field
Description
2
WS
Wait or Stop Status — When the target CPU is in wait or stop mode, most BDC commands cannot function.
However, the BACKGROUND command can be used to force the target CPU out of wait or stop and into active
background mode where all BDC commands work. Whenever the host forces the target MCU into active
background mode, the host should issue a READ_STATUS command to check that BDMACT = 1 before
attempting other BDC commands.
0 Target CPU is running user application code or in active background mode (was not in wait or stop mode when
background became active)
1 Target CPU is in wait or stop mode, or a BACKGROUND command was used to change from wait or stop to
active background mode
1
WSF
Wait or Stop Failure Status — This status bit is set if a memory access command failed due to the target CPU
executing a wait or stop instruction at or about the same time. The usual recovery strategy is to issue a
BACKGROUND command to get out of wait or stop mode into active background mode, repeat the command
that failed, then return to the user program. (Typically, the host would restore CPU registers and stack values and
re-execute the wait or stop instruction.)
0 Memory access did not conflict with a wait or stop instruction
1 Memory access command failed because the CPU entered wait or stop mode
0
DVF
Data Valid Failure Status — This status bit is not used in the MC9S08AW60 Series because it does not have
any slow access memory.
0 Memory access did not conflict with a slow memory access
1 Memory access command failed because CPU was not finished with a slow memory access
15.4.1.2 BDC Breakpoint Match Register (BDCBKPT)
This 16-bit register holds the address for the hardware breakpoint in the BDC. The BKPTEN and FTS
control bits in BDCSCR are used to enable and configure the breakpoint logic. Dedicated serial BDC
commands (READ_BKPT and WRITE_BKPT) are used to read and write the BDCBKPT register but is
not accessible to user programs because it is not located in the normal memory map of the MCU.
Breakpoints are normally set while the target MCU is in active background mode before running the user
application program. For additional information about setup and use of the hardware breakpoint logic in
the BDC, refer to Section 15.2.4, “BDC Hardware Breakpoint.”
15.4.2 System Background Debug Force Reset Register (SBDFR)
This register contains a single write-only control bit. A serial background mode command such as
WRITE_BYTE must be used to write to SBDFR. Attempts to write this register from a user program are
ignored. Reads always return 0x00.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
277
Chapter 15 Development Support
7
6
5
4
3
2
1
0
R
W
0
0
0
0
0
0
0
0
BDFR1
0
Reset
0
0
0
0
0
0
0
= Unimplemented or Reserved
1
BDFR is writable only through serial background mode debug commands, not from user programs.
Figure 15-6. System Background Debug Force Reset Register (SBDFR)
Table 15-3. SBDFR Register Field Description
Description
Field
0
Background Debug Force Reset — A serial active background mode command such as WRITE_BYTE allows
an external debug host to force a target system reset. Writing 1 to this bit forces an MCU reset. This bit cannot
be written from a user program.
BDFR
15.4.3 DBG Registers and Control Bits
The debug module includes nine bytes of register space for three 16-bit registers and three 8-bit control
and status registers. These registers are located in the high register space of the normal memory map so
they are accessible to normal application programs. These registers are rarely if ever accessed by normal
user application programs with the possible exception of a ROM patching mechanism that uses the
breakpoint logic.
15.4.3.1 Debug Comparator A High Register (DBGCAH)
This register contains compare value bits for the high-order eight bits of comparator A. This register is
forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1.
15.4.3.2 Debug Comparator A Low Register (DBGCAL)
This register contains compare value bits for the low-order eight bits of comparator A. This register is
forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1.
15.4.3.3 Debug Comparator B High Register (DBGCBH)
This register contains compare value bits for the high-order eight bits of comparator B. This register is
forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1.
15.4.3.4 Debug Comparator B Low Register (DBGCBL)
This register contains compare value bits for the low-order eight bits of comparator B. This register is
forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1.
MC9S08AW60 Data Sheet, Rev 2
278
Freescale Semiconductor
Chapter 15 Development Support
15.4.3.5 Debug FIFO High Register (DBGFH)
This register provides read-only access to the high-order eight bits of the FIFO. Writes to this register have
no meaning or effect. In the event-only trigger modes, the FIFO only stores data into the low-order byte of
each FIFO word, so this register is not used and will read 0x00.
Reading DBGFH does not cause the FIFO to shift to the next word. When reading 16-bit words out of the
FIFO, read DBGFH before reading DBGFL because reading DBGFL causes the FIFO to advance to the
next word of information.
15.4.3.6 Debug FIFO Low Register (DBGFL)
This register provides read-only access to the low-order eight bits of the FIFO. Writes to this register have
no meaning or effect.
Reading DBGFL causes the FIFO to shift to the next available word of information. When the debug
module is operating in event-only modes, only 8-bit data is stored into the FIFO (high-order half of each
FIFO word is unused). When reading 8-bit words out of the FIFO, simply read DBGFL repeatedly to get
successive bytes of data from the FIFO. It isn’t necessary to read DBGFH in this case.
Do not attempt to read data from the FIFO while it is still armed (after arming but before the FIFO is filled
or ARMF is cleared) because the FIFO is prevented from advancing during reads of DBGFL. This can
interfere with normal sequencing of reads from the FIFO.
Reading DBGFL while the debugger is not armed causes the address of the most-recently fetched opcode
to be stored to the last location in the FIFO. By reading DBGFH then DBGFL periodically, external host
software can develop a profile of program execution. After eight reads from the FIFO, the ninth read will
return the information that was stored as a result of the first read. To use the profiling feature, read the FIFO
eight times without using the data to prime the sequence and then begin using the data to get a delayed
picture of what addresses were being executed. The information stored into the FIFO on reads of DBGFL
(while the FIFO is not armed) is the address of the most-recently fetched opcode.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
279
Chapter 15 Development Support
15.4.3.7 Debug Control Register (DBGC)
This register can be read or written at any time.
7
6
5
4
3
2
1
0
R
W
DBGEN
ARM
TAG
BRKEN
RWA
RWAEN
RWB
RWBEN
Reset
0
0
0
0
0
0
0
0
Figure 15-7. Debug Control Register (DBGC)
Table 15-4. DBGC Register Field Descriptions
Description
Field
7
Debug Module Enable — Used to enable the debug module. DBGEN cannot be set to 1 if the MCU is secure.
DBGEN
0 DBG disabled
1 DBG enabled
6
Arm Control — Controls whether the debugger is comparing and storing information in the FIFO. A write is used
ARM
to set this bit (and ARMF) and completion of a debug run automatically clears it. Any debug run can be manually
stopped by writing 0 to ARM or to DBGEN.
0 Debugger not armed
1 Debugger armed
5
TAG
Tag/Force Select — Controls whether break requests to the CPU will be tag or force type requests. If
BRKEN = 0, this bit has no meaning or effect.
0 CPU breaks requested as force type requests
1 CPU breaks requested as tag type requests
4
Break Enable — Controls whether a trigger event will generate a break request to the CPU. Trigger events can
cause information to be stored in the FIFO without generating a break request to the CPU. For an end trace, CPU
break requests are issued to the CPU when the comparator(s) and R/W meet the trigger requirements. For a
begin trace, CPU break requests are issued when the FIFO becomes full. TRGSEL does not affect the timing of
CPU break requests.
BRKEN
0 CPU break requests not enabled
1 Triggers cause a break request to the CPU
3
R/W Comparison Value for Comparator A — When RWAEN = 1, this bit determines whether a read or a write
access qualifies comparator A. When RWAEN = 0, RWA and the R/W signal do not affect comparator A.
0 Comparator A can only match on a write cycle
RWA
1 Comparator A can only match on a read cycle
2
Enable R/W for Comparator A — Controls whether the level of R/W is considered for a comparator A match.
0 R/W is not used in comparison A
RWAEN
1 R/W is used in comparison A
1
R/W Comparison Value for Comparator B — When RWBEN = 1, this bit determines whether a read or a write
access qualifies comparator B. When RWBEN = 0, RWB and the R/W signal do not affect comparator B.
0 Comparator B can match only on a write cycle
RWB
1 Comparator B can match only on a read cycle
0
Enable R/W for Comparator B — Controls whether the level of R/W is considered for a comparator B match.
0 R/W is not used in comparison B
RWBEN
1 R/W is used in comparison B
MC9S08AW60 Data Sheet, Rev 2
280
Freescale Semiconductor
Chapter 15 Development Support
15.4.3.8 Debug Trigger Register (DBGT)
This register can be read any time, but may be written only if ARM = 0, except bits 4 and 5 are hard-wired
to 0s.
7
6
5
4
3
2
1
0
R
W
0
0
TRGSEL
BEGIN
TRG3
TRG2
TRG1
TRG0
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 15-8. Debug Trigger Register (DBGT)
Table 15-5. DBGT Register Field Descriptions
Description
Field
7
Trigger Type — Controls whether the match outputs from comparators A and B are qualified with the opcode
tracking logic in the debug module. If TRGSEL is set, a match signal from comparator A or B must propagate
through the opcode tracking logic and a trigger event is only signalled to the FIFO logic if the opcode at the match
address is actually executed.
TRGSEL
0 Trigger on access to compare address (force)
1 Trigger if opcode at compare address is executed (tag)
6
Begin/End Trigger Select — Controls whether the FIFO starts filling at a trigger or fills in a circular manner until
a trigger ends the capture of information. In event-only trigger modes, this bit is ignored and all debug runs are
assumed to be begin traces.
BEGIN
0 Data stored in FIFO until trigger (end trace)
1 Trigger initiates data storage (begin trace)
3:0
TRG[3:0]
Select Trigger Mode — Selects one of nine triggering modes, as described below.
0000 A-only
0001 A OR B
0010 A Then B
0011 Event-only B (store data)
0100 A then event-only B (store data)
0101 A AND B data (full mode)
0110 A AND NOT B data (full mode)
0111 Inside range: A ≤ address ≤ B
1000 Outside range: address < A or address > B
1001 – 1111 (No trigger)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
281
Chapter 15 Development Support
15.4.3.9 Debug Status Register (DBGS)
This is a read-only status register.
7
6
5
4
3
2
1
0
R
W
AF
BF
ARMF
0
CNT3
CNT2
CNT1
CNT0
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 15-9. Debug Status Register (DBGS)
Table 15-6. DBGS Register Field Descriptions
Description
Field
7
Trigger Match A Flag — AF is cleared at the start of a debug run and indicates whether a trigger match A
AF
condition was met since arming.
0 Comparator A has not matched
1 Comparator A match
6
Trigger Match B Flag — BF is cleared at the start of a debug run and indicates whether a trigger match B
BF
condition was met since arming.
0 Comparator B has not matched
1 Comparator B match
5
Arm Flag — While DBGEN = 1, this status bit is a read-only image of ARM in DBGC. This bit is set by writing 1
to the ARM control bit in DBGC (while DBGEN = 1) and is automatically cleared at the end of a debug run. A
debug run is completed when the FIFO is full (begin trace) or when a trigger event is detected (end trace). A
debug run can also be ended manually by writing 0 to ARM or DBGEN in DBGC.
0 Debugger not armed
ARMF
1 Debugger armed
3:0
CNT[3:0]
FIFO Valid Count — These bits are cleared at the start of a debug run and indicate the number of words of valid
data in the FIFO at the end of a debug run. The value in CNT does not decrement as data is read out of the FIFO.
The external debug host is responsible for keeping track of the count as information is read out of the FIFO.
0000 Number of valid words in FIFO = No valid data
0001 Number of valid words in FIFO = 1
0010 Number of valid words in FIFO = 2
0011 Number of valid words in FIFO = 3
0100 Number of valid words in FIFO = 4
0101 Number of valid words in FIFO = 5
0110 Number of valid words in FIFO = 6
0111 Number of valid words in FIFO = 7
1000 Number of valid words in FIFO = 8
MC9S08AW60 Data Sheet, Rev 2
282
Freescale Semiconductor
Appendix A
Electrical Characteristics and Timing Specifications
A.1
Introduction
This section contains electrical and timing specifications.
A.2
Parameter Classification
The electrical parameters shown in this supplement are guaranteed by various methods. To give you a
better understanding, the following classification is used and the parameters are tagged accordingly in the
tables where appropriate:
Table A-1. Parameter Classifications
Those parameters are guaranteed during production testing on each individual device.
P
C
Those parameters are achieved by the design characterization by measuring a statistically relevant
sample size across process variations.
Those parameters are achieved by design characterization on a small sample size from typical devices
under typical conditions unless otherwise noted. All values shown in the typical column are within this
category.
T
Those parameters are derived mainly from simulations.
D
NOTE
The classification is shown in the column labeled “C” in the parameter
tables where appropriate.
A.3
Absolute Maximum Ratings
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not
guaranteed. Stress beyond the limits specified in Table A-2 may affect device reliability or cause
permanent damage to the device. For functional operating conditions, refer to the remaining tables in this
section.
This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher than
maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage level (for instance, either V or V ).
SS
DD
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
283
Appendix A Electrical Characteristics and Timing Specifications
Table A-2. Absolute Maximum Ratings
Rating
Symbol
Value
Unit
Supply voltage
Input voltage
V
–0.3 to + 5.8
V
V
DD
V
– 0.3 to VDD + 0.3
In
Instantaneous maximum current
Single pin limit (applies to all port pins)1, 2, 3
ID
25
mA
Maximum current into V
Storage temperature
IDD
120
–55 to +150
150
mA
°C
DD
T
stg
TJ
Maximum junction temperature
°C
1
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp
voltages, then use the larger of the two resistance values.
2
3
All functional non-supply pins are internally clamped to VSS and VDD
.
Power supply must maintain regulation within operating VDD range during instantaneous and
operating maximum current conditions. If positive injection current (VIn > VDD) is greater than
IDD, the injection current may flow out of VDD and could result in external power supply going
out of regulation. Ensure external VDD load will shunt current greater than maximum injection
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low which would reduce overall power
consumption.
MC9S08AW60 Data Sheet, Rev 2
284
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
A.4
Thermal Characteristics
This section provides information about operating temperature range, power dissipation, and package
thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in
on-chip logic and it is user-determined rather than being controlled by the MCU design. In order to take
P
into account in power calculations, determine the difference between actual pin voltage and V or
I/O
SS
V
and multiply by the pin current for each I/O pin. Except in cases of unusually high pin current (heavy
DD
loads), the difference between pin voltage and V or V will be very small.
SS
DD
Table A-3. Thermal Characteristics
Rating
Symbol
Value
Unit
Thermal resistance 1,2,3,4
64-pin QFP
1s
2s2p
57
43
64-pin LQFP
48-pin QFN
44-pin LQFP
1s
2s2p
69
54
θJA
°C/W
1s
2s2p
84
27
1s
2s2p
73
56
1
Junction temperature is a function of die size, on-chip power dissipation, package thermal
resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation
of other components on the board, and board thermal resistance.
2
3
4
Junction to Ambient Natural Convection
1s - Single Layer Board, one signal layer
2s2p - Four Layer Board, 2 signal and 2 power layers
The average chip-junction temperature (T ) in °C can be obtained from:
J
T = T + (P × θ
)
Eqn. A-1
J
A
D
JA
where:
T = Ambient temperature, °C
A
θ = Package thermal resistance, junction-to-ambient, °C/W
JA
P = P + P
D
int
I/O
P = I × V , Watts — chip internal power
int
DD
DD
P
= Power dissipation on input and output pins — user determined
I/O
For most applications, P << P and can be neglected. An approximate relationship between P and T
J
I/O
int
D
(if P is neglected) is:
I/O
P = K ÷ (T + 273°C)
Eqn. A-2
D
J
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
285
Appendix A Electrical Characteristics and Timing Specifications
Solving equations 1 and 2 for K gives:
2
K = P × (T + 273°C) + θ × (P )
Eqn. A-3
D
A
JA
D
where K is a constant pertaining to the particular part. K can be determined from equation 3 by measuring
P (at equilibrium) for a known T . Using this value of K, the values of P and T can be obtained by
D
A
D
J
solving equations 1 and 2 iteratively for any value of T .
A
A.5
ESD Protection and Latch-Up Immunity
Although damage from electrostatic discharge (ESD) is much less common on these devices than on early
CMOS circuits, normal handling precautions should be used to avoid exposure to static discharge.
Qualification tests are performed to ensure that these devices can withstand exposure to reasonable levels
of static without suffering any permanent damage.
All ESD testing is in conformity with AEC-Q100 Stress Test Qualification for Automotive Grade
Integrated Circuits. During the device qualification ESD stresses were performed for the Human Body
Model (HBM), the Machine Model (MM) and the Charge Device Model (CDM).
A device is defined as a failure if after exposure to ESD pulses the device no longer meets the device
specification. Complete DC parametric and functional testing is performed per the applicable device
specification at room temperature followed by hot temperature, unless specified otherwise in the device
specification.
Table A-4. ESD and Latch-up Test Conditions
Model
Description
Symbol
Value
Unit
Ω
Series Resistance
R1
1500
Human Body
Model
Storage Capacitance
C
100
3
pF
Number of Pulse per pin
—
Series Resistance
R1
0
Ω
Machine Model
Latch-Up
Storage Capacitance
C
200
3
pF
Number of Pulse per pin
Minimum input voltage limit
Maximum input voltage limit
—
–2.5
7.5
V
V
Table A-5. ESD and Latch-Up Protection Characteristics
Num C
Rating
Symbol
VHBM
VMM
Min
2000
200
500
100
Max
Unit
1
2
3
4
C Human Body Model (HBM)
—
—
—
—
V
V
C Machine Model (MM)
VCDM
ILAT
C Charge Device Model (CDM)
V
Latch-up Current at TA = 125°C
C
mA
MC9S08AW60 Data Sheet, Rev 2
286
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
A.6
DC Characteristics
This section includes information about power supply requirements, I/O pin characteristics, and power
supply current in various operating modes.
Table A-6. MCU Operating Conditions
Uni
Characteristic
Min
Typ
Max
t
Supply Voltage
Temperature
2.7
—
5.5
V
°C
M
V
C
–40
–40
-40
—
—
—
125
105
85
Table A-7. DC Characteristics
Num C
Parameter
Symbol
Min
Typ1
Max
Unit
Output high voltage — Low Drive (PTxDSn = 0)
5 V, ILoad = –2 mA
VDD – 1.5
—
—
—
—
—
—
—
—
3 V, ILoad = –0.6 mA
5 V, ILoad = –0.4 mA
3 V, ILoad = –0.24 mA
VDD – 1.5
VDD – 0.8
VDD – 0.8
1
P
VOH
V
Output high voltage — High Drive (PTxDSn = 1)
5 V, ILoad = –10 mA
VDD – 1.5
VDD – 1.5
VDD – 0.8
VDD – 0.8
—
—
—
—
—
—
—
—
3 V, ILoad = –3 mA
5 V, ILoad = –2 mA
3 V, ILoad = –0.4 mA
Output low voltage — Low Drive (PTxDSn = 0)
5 V, ILoad = 2 mA
—
—
—
—
—
—
—
—
1.5
1.5
0.8
0.8
3 V, ILoad = 0.6 mA
5 V, ILoad = 0.4 mA
3 V, ILoad = 0.24 mA
2
P
VOL
V
Output low voltage — High Drive (PTxDSn = 1)
5 V, ILoad = 10 mA
—
—
—
—
—
—
—
—
1.5
1.5
0.8
0.8
3 V, ILoad = 3 mA
5 V, ILoad = 2 mA
3 V, ILoad = 0.4 mA
3
4
D Output high current — Max total IOH for all ports
5V IOHT
3V
—
—
—
—
100
60
mA
mA
V
D Output low current — Max total IOL for all ports
5V IOLT
3V
—
—
—
—
100
60
5
6
7
8
P Input high voltage; all digital inputs
P Input low voltage; all digital inputs
T Input hysteresis; all digital inputs
P Input leakage current; input only pins2
VIH
VIL
0.65 x VDD
—
—
—
—
0.06 x VDD
—
0.35 x VDD
Vhys
|IIn|
mV
0.01
1
μA
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
287
Appendix A Electrical Characteristics and Timing Specifications
Table A-7. DC Characteristics (continued)
Num C
Parameter
Symbol
|IOZ
Min
Typ1
Max
Unit
9
P High Impedance (off-state) leakage current2
|
—
20
20
—
0.01
45
1
65
65
8
µA
kΩ
kΩ
pF
V
10 P Internal pullup resistors3
RPU
RPD
CIn
11 P Internal pulldown resistors4
12 C Input Capacitance; all non-supply pins
13 P POR rearm voltage
45
—
VPOR
tPOR
0.9
10
1.4
—
2.0
—
14 D POR rearm time
µs
15 P Low-voltage detection threshold — high range
VDD falling VLVDH
DD rising
4.2
4.3
4.3
4.4
4.4
4.5
V
V
V
V
V
Low-voltage detection threshold — low range
DD falling VLVDL
DD rising
16
17
18
19
P
P
P
P
V
V
2.48
2.54
2.56
2.62
2.64
2.7
Low-voltage warning threshold — high range
DD falling VLVWH
DD rising
V
V
4.2
4.3
4.3
4.4
4.4
4.5
Low-voltage warning threshold — low range
DD falling VLVWL
DD rising
V
V
2.48
2.54
2.56
2.62
2.64
2.7
Low-voltage inhibit reset/recover hysteresis
5V Vhys
3V
—
—
100
60
—
—
mV
V
20 P Bandgap Voltage Reference
VBG
1.185
1.20
1.215
Factory trimmed at
DD = 5.0 V
Temp = 25 °C
V
5, 6, 7, 8
21 D dc injection current
DC Injection Current
Single pin limit
V
IN > VDD
VIN < VSS
Total MCU limit, includes sum of all stressed pins
IN > VDD
VIN < VSS
0
0
-
-
2
–0.2
mA
mA
|IIC|
V
0
0
-
-
25
–5
mA
mA
1
2
3
4
5
Typical values are based on characterization data at 25°C unless otherwise stated.
Measured with VIn = VDD or VSS
Measured with VIn = VSS
Measured with VIn = VDD
.
.
.
Power supply must maintain regulation within operating VDD range during instantaneous and operating
maximum current conditions. If positive injection current (VIn > VDD) is greater than IDD, the injection current
may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD
load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU
is not consuming power. Examples are: if no system clock is present, or if clock rate is very low which (would
reduce overall power consumption).
6
7
All functional non-supply pins are internally clamped to VSS and VDD
.
Input must be current limited to the value specified. To determine the value of the required current-limiting
resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two
values.
MC9S08AW60 Data Sheet, Rev 2
288
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
8
IRQ does not have a clamp diode to VDD. Do not drive IRQ above VDD
.
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0.8
0.7
0.6
0.5
0.4
0.3
0.2
125ºC
85ºC
25ºC
40ºC
125ºC
85ºC
25ºC
40ºC
IOL = 2mA
VDD = 5V
0.2
0.6
1.2
1.6
2.0
2.4
3.0
2.75 3.0 3.25 3.5 3.75 4.0 4.25 4.5 4.75 5.0 5.25 5.5
I
OL (mA)
VDD (V)
Figure A-1. Typical Low-Side Driver (Sink) Characteristics — Low Drive (PTxDS = 0)
n
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.4
1.3
125ºC
85ºC
25ºC
40ºC
125ºC
IOL = +10mA
85ºC
25ºC
40ºC
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
VDD = 5V
0.2 1.2 1.6 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
3.0
4.0
5.0
IOL (mA)
V
DD (V)
Figure A-2. Typical Low-Side Driver (Sink) Characteristics — High Drive (PTxDS = 1)
n
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
289
Appendix A Electrical Characteristics and Timing Specifications
1.2
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
125ºC
85ºC
25ºC
40ºC
125ºC
85ºC
25ºC
40ºC
1.0
0.8
0.6
0.4
0.2
0
VDD = 5V
IOH = -2mA
0.2
0.6
1.2
1.6
IOH (mA)
2.0
2.4
3.0
2.75 3.0 3.25 3.5 3.75 4.0 4.25 4.5 4.75 5.0 5.25 5.5
VDD (V)
Figure A-3. Typical High-Side (Source) Characteristics — Low Drive (PTxDS = 0)
n
1.2
1.0
0.8
0.6
0.4
0.2
0
1.5
1.4
125ºC
85ºC
25ºC
40ºC
125ºC
85ºC
25ºC
40ºC
1.3
1.2
1.1
1.0
0.9
0.8
0.7
0.6
VDD = 5V
IOH = -10mA
0.2 1.2 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
3.0
4.0
5.0
IOH (mA)
VDD (V)
Figure A-4. Typical High-Side (Source) Characteristics — High Drive (PTxDSn = 1)
MC9S08AW60 Data Sheet, Rev 2
290
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
A.7
Supply Current Characteristics
Table A-8. Supply Current Characteristics
VDD
(V)
Temp
(°C)
Typ1
Num
C
Parameter
Symbol
Max
Unit
Run supply current2 measured at
(CPU clock = 2 MHz, fBus = 1 MHz)
5
3
5
3
5
3
0.750
0.570
4.90
3.50
16.8
11.5
0.950
0.770
5.10
3.70
18.5
12.5
1
P
RIDD
mA
–40 to 125°C
–40 to 125°C
–40 to 125°C
Run supply current2 measured at
(CPU clock = 16 MHz, fBus = 8 MHz)
2
3
P
P
RIDD
mA
mA
Run supply current3 measured at (CPU
clock = 40 MHz, fBus = 20 MHz)
RIDD
Stop2 mode supply current
18.0
60
–40 to 85°C
–40 to 125°C
5
3
0.900
0.720
μA
μA
4
5
6
P
P
C
17.0
50
–40 to 85°C
–40 to 125°C
S2IDD
Stop3 mode supply current
20.0
90
–40 to 85°C
–40 to 125°C
5
0.975
μA
S3IDD
19.0
85
–40 to 85°C
–40 to 125°C
3
5
0.825
300
μA
500
500
–40 to 85°C
–40 to 125°C
nA
RTI adder to stop2 or stop34
S23IDDRTI
500
500
–40 to 85°C
–40 to 125°C
3
300
nA
5
3
110
90
180
160
μA
μA
–40 to 125°C
–40 to 125°C
7
8
C
C
LVD adder to stop3 (LVDE = LVDSE = 1)
S3IDDLVD
Adder to stop3 for oscillator enabled
(OSCSTEN =1)5
5,3
5
8
μA
–40 to 125°C
S3IDDOSC
1
Typical values are based on characterization data at 25°C unless otherwise stated. See Figure A-5 through Figure A-7 for
typical curves across voltage/temperature.
2
3
4
All modules except ADC enabled, but not active. ICG configured for FBE. Does not include any DC loads on port pins.
All modules except ADC active, ICG configured for FBE and does not include any DC loads on port pins
Most customers are expected to find that auto-wakeup from stop2 or stop3 can be used instead of the higher current wait
mode. Wait mode typical is 500 μA at 5 V with fBus = 1 MHz.
Values given under the following conditions: low range operation (RANGE = 0) with a 32.768 kHz crystal, low power mode
(HGO = 0), clock monitor disabled (LOCD = 1).
5
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
291
Appendix A Electrical Characteristics and Timing Specifications
24.0
20 MHz – FEI Clock Mode, ADC Module Off
22.0
20.0
18.0
16.0
14.0
12.0
10.0
8.0
20 MHz – FBE Clock Mode, ADC Module Off
8 MHz – FEI Clock Mode, ADC Module Off
8 MHz – FBE Clock Mode, ADC Module Off
1 MHz – FEI Clock Mode, ADC Module Off
1 MHz – FBE Clock Mode, ADC Module Off
6.0
4.0
2.0
0
2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
VDD (V)
Note: All modules except ADC active.
Figure A-5. Typical Run I for FBE and FEI Modes, I vs. V
DD
DD
DD
Stop2 I (A)
DD
Average of Meas I
DD
4.000E–05
3.500E–05
3.000E–05
2.500E–05
Temp
–40
2.000E–05
1.500E–05
1.000E–05
25
85
125
5.000E–06
0.000E+00
1.8
3.5
(V)
4.5
2
2.5
3
4
5
V
DD
Figure A-6. Typical Stop 2 I
DD
MC9S08AW60 Data Sheet, Rev 2
292
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
Stop3 I (A)
DD
Average of Meas I
DD
50.0E–6
45.0E–6
40.0E–6
35.0E–6
30.0E–6
25.0E–6
20.0E–6
15.0E–6
10.0E–6
Temp
–40
25
85
125
5.0E–6
000.0E+0
1.8
3.5
(V)
4.5
2
2.5
3
4
5
V
DD
Figure A-7. Typical Stop3 I
DD
A.8
ADC Characteristics
Table A-9. 5 Volt 10-bit ADC Operating Conditions
Characteristic
Supply voltage
Conditions
Symb
Min
Typ1
Max
Unit
Absolute
Delta to VDD (VDD–VDDAD
VDDAD
ΔVDDAD
ΔVSSAD
VREFH
2.7
–100
–100
2.7
—
5.5
V
mV
mV
V
2
)
0
0
+100
+100
VDDAD
2
Ground voltage
Ref voltage high
Delta to VSS (VSS–VSSAD)
VDDAD
Ref voltage low
VREFL
VSSAD
VSSAD
VSSAD
V
Input voltage
VADIN
CADIN
RADIN
RAS
VREFL
—
—
4.5
3
VREFH
5.5
V
Input capacitance
Input resistance
pF
kΩ
kΩ
—
5
Analog source resistance
External to MCU
10-bit mode
fADCK > 4MHz
ADCK < 4MHz
—
—
—
—
5
10
f
8-bit mode (all valid fADCK
High speed (ADLPC = 0)
Low power (ADLPC = 1)
)
—
—
—
—
10
8.0
4.0
ADC conversion clock frequency
fADCK
0.4
0.4
MHz
1
2
Typical values assume VDDAD = 5.0 V, Temp = 25°C, fADCK = 1.0MHz unless otherwise stated. Typical values are for reference
only and are not tested in production.
dc potential difference.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
293
Appendix A Electrical Characteristics and Timing Specifications
SIMPLIFIED
INPUT PIN EQUIVALENT
CIRCUIT
Z
ADIN
SIMPLIFIED
CHANNEL SELECT
CIRCUIT
Pad
Z
AS
leakage
due to
input
ADC SAR
ENGINE
R
R
AS
ADIN
protection
+
V
ADIN
–
C
AS
V
+
AS
–
R
ADIN
INPUT PIN
INPUT PIN
INPUT PIN
R
ADIN
R
ADIN
C
ADIN
Figure A-8. ADC Input Impedance Equivalency Diagram
Table A-10. 10-bit ADC Characteristics (V
= V
, V
= V
)
SSAD
REFH
DDAD REFL
Characteristic
Conditions
C
Symb
Min
Typ1
Max
Unit
Supply current
ADLPC = 1
ADLSMP = 1
ADCO = 1
T
IDDAD
IDDAD
IDDAD
IDDAD
IDDAD
—
133
—
μA
Supply current
ADLPC = 1
ADLSMP = 0
ADCO = 1
T
T
P
—
—
—
—
218
327
—
—
μA
μA
μA
μA
Supply current
ADLPC = 0
ADLSMP = 1
ADCO = 1
Supply current
ADLPC = 0
ADLSMP = 0
ADCO = 1
V
DDAD < 5.5 V
582
990
1
Supply current
Stop, reset,
module off
0.011
MC9S08AW60 Data Sheet, Rev 2
294
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
Table A-10. 10-bit ADC Characteristics (V
= V
, V
= V
) (continued)
SSAD
REFH
DDAD REFL
Characteristic
Conditions
High speed
C
Symb
Min
Typ1
3.3
Max
Unit
ADC asynchronous clock
source
tADACK = 1/fADACK
P
P
P
fADACK
2
1.25
—
5
MHzS
(ADLPC = 0)
Low power
(ADLPC = 1)
2
20
3.3
—
—
—
—
Conversion time
(Including sample time)
Short sample
(ADLSMP = 0)
tADC
ADCK
cycles
Long sample
(ADLSMP = 1)
—
40
Sample time
Short sample
(ADLSMP = 0)
tADS
—
3.5
23.5
ADCK
cycles
Long sample
—
(ADLSMP = 1)
Total unadjusted error
Includes quantization
10-bit mode
8-bit mode
10-bit mode
8-bit mode
P
P
ETUE
DNL
—
—
—
—
1
2.5
1.0
1.0
0.5
LSB2
LSB2
0.5
0.5
0.3
Differential non-linearity
Monotonicity and no-missing-codes guaranteed
Integral non-linearity
Zero-scale error
10-bit mode
8-bit mode
10-bit mode
8-bit mode
10-bit mode
8-bit mode
10-bit mode
8-bit mode
10-bit mode
8-bit mode
-40°C - 25°C
25°C - 125°C
25°C
C
P
P
D
D
INL
EZS
EFS
EQ
—
—
—
—
—
—
—
—
—
—
—
—
0.5
0.3
1.0
0.5
1.5
0.5
1.5
0.5
0.5
0.5
2.5
1
LSB2
LSB2
LSB2
LSB2
LSB2
mV/°C
0.5
VADIN = VSSA
0.5
Full-scale error
ADIN = VDDA
0.5
V
0.5
Quantization error
—
—
Input leakage error
Pad leakage3 * RAS
EIL
0.2
0.1
3.266
3.638
1.396
—
Temp sensor slope
Temp sensor voltage
T
m
—
—
V
V
TEMP25
P
—
1
Typical values assume VDDAD = 5.0V, Temp = 25C, fADCK=1.0 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
2
3
1 LSB = (VREFH – VREFL)/2N
Based on input pad leakage current. Refer to pad electricals.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
295
Appendix A Electrical Characteristics and Timing Specifications
A.9
Internal Clock Generation Module Characteristics
ICG
EXTAL
XTAL
RS
R
F
Crystal or Resonator
C
1
C
2
Table A-11. ICG DC Electrical Specifications (Temperature Range = –40 to 125°C Ambient)
Characteristic
Symbol
Min
Typ1
Max
Unit
Load capacitors
Feedback resistor
C1
C2
See Note 2
Low range (32k to 100 kHz)
High range (1M – 16 MHz)
RF
10
1
MΩ
MΩ
Series resistor
Low range
Low Gain (HGO = 0)
High Gain (HGO = 1)
High range
—
—
0
100
—
—
RS
kΩ
Low Gain (HGO = 0)
High Gain (HGO = 1)
≥ 8 MHz
—
0
—
—
—
—
0
10
20
—
—
—
4 MHz
1 MHz
1
2
Typical values are based on characterization data at VDD = 5.0V, 25°C or is typical recommended value.
See crystal or resonator manufacturer’s recommendation.
MC9S08AW60 Data Sheet, Rev 2
296
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
A.9.1
ICG Frequency Specifications
Table A-12. ICG Frequency Specifications
(min) to V (max), Temperature Range = –40 to 125°C Ambient)
(V
= V
DDA
DDA
DDA
Num
C
Characteristic
Symbol
Min
Typ1
Max
Unit
Oscillator crystal or resonator (REFS = 1)
(Fundamental mode crystal or ceramic resonator)
Low range
flo
32
—
100
kHz
High range
1
T
High Gain, FBE (HGO = 1,CLKS = 10)
High Gain, FEE (HGO = 1,CLKS = 11)
Low Power, FBE (HGO = 0, CLKS = 10)
Low Power, FEE (HGO = 0, CLKS = 11)
fhi_byp
fhi_eng
flp_byp
flp_eng
1
2
1
2
—
—
16
10
8
MHz
MHz
MHz
MHz
8
Input clock frequency (CLKS = 11, REFS = 0)
flo
fhi_eng
Low range
High range
2
T
32
2
—
—
100
10
kHz
MHz
fExtal
fICGIRCLK
tdc
3
4
5
T
P
P
0
—
243
—
40
303.75
60
MHz
kHz
%
Input clock frequency (CLKS = 10, REFS = 0)
Internal reference frequency (untrimmed)
Duty cycle of input clock (REFS = 0)
182.25
40
Output clock ICGOUT frequency
CLKS = 10, REFS = 0
All other cases
f
Extal (max)
fExtal (min)
flo (min)
fICGOUT
6
P
—
—
fICGDCLKmax MHz
(max)
Minimum DCO clock (ICGDCLK) frequency
Maximum DCO clock (ICGDCLK) frequency
Self-clock mode (ICGOUT) frequency 2
Self-clock mode reset (ICGOUT) frequency
fICGDCLKmin
fICGDCLKmax
fSelf
7
8
8
—
—
MHz
40
MHz
MHz
MHz
fICGDCLKmin
5.5
fICGDCLKmax
9
P
P
fSelf_reset
10
8
10.5
Loss of reference frequency 3
Low range
High range
Loss of DCO frequency 4
Crystal start-up time 5, 6
Low range
fLOR
fLOD
11
12
13
T
T
T
5
50
25
500
kHz
0.5
1.5
MHz
t
CSTL
—
—
430
4
—
—
t
ms
ms
CSTH
High range
7
FLL lock time
Low range
High range
tLockl
tLockh
14
P
—
—
5
5
FLL frequency unlock range
FLL frequency lock range
nUnlock
nLock
15
16
T
T
–4*N
–2*N
4*N
2*N
counts
counts
ICGOUT period jitter, 8 measured at fICGOUT Max
Long term jitter (averaged over 2 ms interval)
CJitter
17
18
T
T
% fICG
V
—
0.2
Oscillator Amplitude (peak-to-peak)
Voscamp
HGO = 0
HGO = 1
—
—
1
VDD
—
—
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
297
Appendix A Electrical Characteristics and Timing Specifications
Table A-12. ICG Frequency Specifications (continued)
(min) to V (max), Temperature Range = –40 to 125°C Ambient)
(V
= V
DDA
DDA
DDA
Num
C
Characteristic
Symbol
Min
Typ1
Max
Unit
MC9S08AWxx: Internal oscillator deviation from trimmed frequency9
VDD = 2.7 – 5.5 V, (constant temperature)
ACCint
0.5
0.5
C
P
—
—
2
2
%
%
VDD = 5.0 V 10%, –40° C to 125°C
19
S9S08AWxx: Internal oscillator deviation from trimmed frequency9
VDD = 2.7 – 5.5 V, (constant temperature)
ACCint
0.5
C
P
P
—
—
—
1.5
1.5
2
%
%
%
VDD = 5.0 V 10%, –40° C to 85°C
VDD = 5.0 V 10%, –40° C to 125°C
0.5
0.5
1
2
3
Typical values are based on characterization data at VDD = 5.0V, 25°C unless otherwise stated.
Self-clocked mode frequency is the frequency that the DCO generates when the FLL is open-loop.
Loss of reference frequency is the reference frequency detected internally, which transitions the ICG into self-clocked mode if it
is not in the desired range.
4
Loss of DCO frequency is the DCO frequency detected internally, which transitions the ICG into FLL bypassed external mode
(if an external reference exists) if it is not in the desired range.
5
6
7
This parameter is characterized before qualification rather than 100% tested.
Proper PC board layout procedures must be followed to achieve specifications.
This specification applies to the period of time required for the FLL to lock after entering FLL engaged internal or external modes.
If a crystal/resonator is being used as the reference, this specification assumes it is already running.
8
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fICGOUT
.
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via VDDA and VSSA and variation in crystal oscillator frequency increase the CJitter percentage for
a given interval.
9
See Figure A-9.
MC9S08AW60 Data Sheet, Rev 2
298
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
Internal Oscillator Deviation from Trimmed Frequency
Variable
5 V
0.0
–0.5
–1.0
3 V
–1.5
–2.0
–50
–25
0
25
50
Temp
75
100
125
Device trimmed at 25°C at 3.0 V.
Figure A-9. Internal Oscillator Deviation from Trimmed Frequency
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
299
Appendix A Electrical Characteristics and Timing Specifications
A.10 AC Characteristics
This section describes ac timing characteristics for each peripheral system. For detailed information about
how clocks for the bus are generated, see Chapter 8, “Internal Clock Generator (S08ICGV4).”
A.10.1 Control Timing
Table A-13. Control Timing
Num
C
Parameter
Bus frequency (tcyc = 1/fBus
Symbol
fBus
Min
dc
Typ1
Max
20
Unit
MHz
μs
1
2
3
)
—
P
tRTI
Real-time interrupt internal oscillator period
External reset pulse width2
700
1300
1.5 x
tSelf_reset
textrst
—
ns
(tcyc = 1/fSelf_reset
)
Reset low drive3
4
trstdrv
tMSSU
tMSH
34 x tcyc
25
—
—
—
ns
ns
ns
5
Active background debug mode latch setup time
Active background debug mode latch hold time
6
25
IRQ pulse width
Asynchronous path2
Synchronous path4
tILIH, IHIL
t
100
1.5 x tcyc
—
—
—
—
ns
ns
7
8
KBIPx pulse width
Asynchronous path2
Synchronous path3
tILIH, IHIL
t
100
1.5 x tcyc
Port rise and fall time —
Low output drive (PTxDS = 0) (load = 50 pF)5
Slew rate control disabled (PTxSE = 0)
Slew rate control enabled (PTxSE = 1)
tRise, tFall
ns
ns
—
—
40
75
—
—
9
T
Port rise and fall time —
High output drive (PTxDS = 1) (load = 50 pF)
Slew rate control disabled (PTxSE = 0)
Slew rate control enabled (PTxSE = 1)
tRise, tFall
—
—
11
35
—
—
1
2
Typical values are based on characterization data at VDD = 5.0V, 25°C unless otherwise stated.
This is the shortest pulse that is guaranteed to be recognized as a reset pin request. Shorter pulses are not guaranteed to
override reset requests from internal sources.
3
4
5
When any reset is initiated, internal circuitry drives the reset pin low for about 34 bus cycles and then samples the level on
the reset pin about 38 bus cycles later to distinguish external reset requests from internal requests.
This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or
may not be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized in that case.
Timing is shown with respect to 20% VDD and 80% VDD levels. Temperature range –40°C to 125°C.
MC9S08AW60 Data Sheet, Rev 2
300
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
1300
1250
1200
1150
1100
1050
1000
950
+3 SD
Mean
–3 SD
900
850
800
–40
–20
0
20
40
60
80
100
120
Temperature (ºC)
Figure A-10. Typical RTI Clock Period vs. Temperature
t
extrst
RESET PIN
Figure A-11. Reset Timing
BKGD/MS
RESET
t
MSH
t
MSSU
Figure A-12. Active Background Debug Mode Latch Timing
t
IHIL
IRQ/KBIP7-KBIP4
IRQ/KBIPx
t
ILIH
Figure A-13. IRQ/KBIPx Timing
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
301
Appendix A Electrical Characteristics and Timing Specifications
A.10.2 Timer/PWM (TPM) Module Timing
Synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that
can be used as the optional external source to the timer counter. These synchronizers operate from the
current bus rate clock.
Table A-14. TPM Input Timing
Function
External clock frequency
External clock period
Symbol
fTPMext
tTPMext
tclkh
Min
dc
Max
fBus/4
—
Unit
Hz
tcyc
tcyc
tcyc
tcyc
4
External clock high time
External clock low time
Input capture pulse width
1.5
1.5
1.5
—
tclkl
—
tICPW
—
t
TPMext
t
clkh
TPMxCLK
t
clkl
Figure A-14. Timer External Clock
t
ICPW
TPMxCHn
TPMxCHn
t
ICPW
Figure A-15. Timer Input Capture Pulse
MC9S08AW60 Data Sheet, Rev 2
302
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
A.11 SPI Characteristics
Table A-15 and Figure A-16 through Figure A-19 describe the timing requirements for the SPI system.
Table A-15. SPI Electrical Characteristic
Num1
C
Characteristic2
Symbol
Min
Max
Unit
Operating frequency3
Master
Slave
Hz
f
/2048
dc
f
f
/2
/4
f
Bus
Bus
Bus
op
f
op
1
2
Cycle time
Master
Slave
2
4
2048
—
tcyc
tcyc
tSCK
tSCK
Enable lead time
Master
Slave
—
1/2
t
t
1/2
—
t
t
Lead
Lead
SCK
SCK
3
Enable lag time
Master
Slave
—
1/2
t
t
1/2
—
t
t
Lag
Lag
SCK
SCK
4
5
6
Clock (SPSCK) high time
Master and Slave
1/2 tSCK – 25
1/2 tSCK – 25
—
—
ns
ns
t
SCKH
Clock (SPSCK) low time Master
and Slave
t
SCKL
Data setup time (inputs)
Master
Slave
30
30
—
—
ns
ns
t
t
SI(M)
SI(S)
7
Data hold time (inputs)
Master
Slave
30
30
—
—
ns
ns
t
t
HI(M)
HI(S)
8
9
Access time, slave4
Disable time, slave5
0
40
40
ns
ns
t
A
—
t
dis
10
Data setup time (outputs)
Master
Slave
25
25
—
—
ns
ns
t
t
SO
SO
11
Data hold time (outputs)
Master
Slave
–10
–10
—
—
ns
ns
t
t
HO
HO
1
2
Refer to Figure A-16 through Figure A-19.
All timing is shown with respect to 20% V
and 70% V , unless noted; 100 pF load on all SPI
DD
DD
pins. All timing assumes slew rate control disabled and high drive strength enabled for SPI output
pins.
3
4
5
Maximum baud rate must be limited to 5 MHz due to pad input characteristics.
Time to data active from high-impedance state.
Hold time to high-impedance state.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
303
Appendix A Electrical Characteristics and Timing Specifications
1
SS
(OUTPUT)
1
2
3
SCK
(CPOL = 0)
(OUTPUT)
5
4
4
5
SCK
(CPOL = 1)
(OUTPUT)
6
7
MISO
(INPUT)
2
MSB IN
10
BIT 6 . . . 1
LSB IN
10
11
MOSI
(OUTPUT)
2
BIT 6 . . . 1
LSB OUT
MSB OUT
NOTES:
1. SS output mode (MODFEN = 1, SSOE = 1).
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure A-16. SPI Master Timing (CPHA = 0)
(1)
SS
(OUTPUT)
1
2
3
SCK
(CPOL = 0)
(OUTPUT)
5
4
SCK
(CPOL = 1)
5
4
(OUTPUT)
6
7
MISO
(INPUT)
(2)
MSB IN
BIT 6 . . . 1
11
BIT 6 . . . 1
LSB IN
10
MOSI
(OUTPUT)
(2)
LSB OUT
MSB OUT
NOTES:
1. SS output mode (MODFEN = 1, SSOE = 1).
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure A-17. SPI Master Timing (CPHA = 1)
MC9S08AW60 Data Sheet, Rev 2
304
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
SS
(INPUT)
3
1
SCK
5
4
(CPOL = 0)
4
5
(INPUT)
2
SCK
(CPOL = 1)
(INPUT)
9
8
11
10
MISO
(OUTPUT)
SEE
NOTE
BIT 6 . . . 1
BIT 6 . . . 1
SLAVE LSB OUT
MSB OUT
7
SLAVE
6
MOSI
(INPUT)
MSB IN
LSB IN
NOTE:
1. Not defined but normally MSB of character just received
Figure A-18. SPI Slave Timing (CPHA = 0)
SS
(INPUT)
1
3
2
SCK
(CPOL = 0)
(INPUT)
5
4
SCK
(CPOL = 1)
5
4
(INPUT)
10
11
9
MISO
(OUTPUT)
SEE
BIT 6 . . . 1
SLAVE LSB OUT
LSB IN
SLAVE MSB OUT
NOTE
6
7
8
MOSI
(INPUT)
MSB IN
BIT 6 . . . 1
NOTE:
1. Not defined but normally LSB of character just received
Figure A-19. SPI Slave Timing (CPHA = 1)
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
305
Appendix A Electrical Characteristics and Timing Specifications
A.12 FLASH Specifications
This section provides details about program/erase times and program-erase endurance for the FLASH
memory.
Program and erase operations do not require any special power sources other than the normal V supply.
DD
For more detailed information about program/erase operations, see Chapter 4, “Memory.”
Table A-16. FLASH Characteristics
Num
C
P
P
P
P
Characteristic
Symbol
Vprog/erase
VRead
fFCLK
Min
2.7
2.7
150
5
Typ1
Max
5.5
Unit
1
2
3
4
Supply voltage for program/erase
Supply voltage for read operation
V
5.5
V
Internal FCLK frequency2
200
6.67
kHz
μs
tFcyc
Internal FCLK period (1/FCLK)
Byte program time (random location)3
Byte program time (burst mode)3
Page erase time3
tprog
tFcyc
tFcyc
tFcyc
tFcyc
5
P
9
4
6
C
tBurst
tPage
7
P
4000
Mass erase time3
8
P
tMass
20,000
Program/erase endurance4
9
C
C
10,000
—
—
100,000
—
—
cycles
years
TL to TH = –40°C to + 125°C
T = 25°C
Data retention5
tD_ret
10
15
100
—
1
2
3
Typical values are based on characterization data at VDD = 5.0 V, 25°C unless otherwise stated.
The frequency of this clock is controlled by a software setting.
These values are hardware state machine controlled. User code does not need to count cycles. This information
supplied for calculating approximate time to program and erase.
4
5
Typical endurance for FLASH was evaluated for this product family on the 9S12Dx64. For additional information
on how Freescale Semiconductor defines typical endurance, please refer to Engineering Bulletin EB619/D, Typical
Endurance for Nonvolatile Memory.
Typical data retention values are based on intrinsic capability of the technology measured at high temperature and
de-rated to 25°C using the Arrhenius equation. For additional information on how Freescale Semiconductor defines
typical data retention, please refer to Engineering Bulletin EB618/D, Typical Data Retention for Nonvolatile Memory.
MC9S08AW60 Data Sheet, Rev 2
306
Freescale Semiconductor
Appendix A Electrical Characteristics and Timing Specifications
A.13 EMC Performance
Electromagnetic compatibility (EMC) performance is highly dependant on the environment in which the
MCU resides. Board design and layout, circuit topology choices, location and characteristics of external
components as well as MCU software operation all play a significant role in EMC performance. The
system designer should consult Freescale applications notes such as AN2321, AN1050, AN1263,
AN2764, and AN1259 for advice and guidance specifically targeted at optimizing EMC performance.
A.13.1 Radiated Emissions
Microcontroller radiated RF emissions are measured from 150 kHz to 1 GHz using the TEM/GTEM Cell
method in accordance with the IEC 61967-2 and SAE J1752/3 standards. The measurement is performed
with the microcontroller installed on a custom EMC evaluation board while running specialized EMC test
software. The radiated emissions from the microcontroller are measured in a TEM cell in two package
orientations (North and East). For more detailed information concerning the evaluation results, conditions
and setup, please refer to the EMC Evaluation Report for this device.
The maximum radiated RF emissions of the tested configuration in all orientations are less than or equal
to the reported emissions levels.
Table A-17. Radiated Emissions
Level1
Parameter
Symbol
Conditions
fOSC/fBUS
Frequency
Unit
(Max)
4 MHz crystal
20 MHz Bus
0.15 – 50 MHz
50 – 150 MHz
150 – 500 MHz
500 – 1000 MHz
IEC Level
16
3
dBμV
1
0
L
—
—
VDD = 5.5V
SAE Level
2
TA = +25oC
package type
64 QFP
Radiated emissions,
electric field
VRE_TEM
32 kHz crystal
8 MHz Bus
0.15 – 50 MHz
50 – 150 MHz
150 – 500 MHz
500 – 1000 MHz
IEC Level
-1
-6
-10
-10
N
dBμV
—
—
SAE Level
1
1
Data based on qualification test results.
A.13.2 Conducted Transient Susceptibility
Microcontroller transient conducted susceptibility is measured in accordance with an internal Freescale
test method. The measurement is performed with the microcontroller installed on a custom EMC
evaluation board and running specialized EMC test software designed in compliance with the test method.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
307
Appendix A Electrical Characteristics and Timing Specifications
The conducted susceptibility is determined by injecting the transient susceptibility signal on each pin of
the microcontroller. The transient waveform and injection methodology is based on IEC 61000-4-4
(EFT/B). The transient voltage required to cause performance degradation on any pin in the tested
configuration is greater than or equal to the reported levels unless otherwise indicated by footnotes below
the table.
Table A-18. Conducted Susceptibility
Amplitude1
fOSC/fBUS
Parameter
Symbol
Conditions
Result
Unit
(Min)
0
A
B
C
D
2.02
VDD = 5.5V
TA = +25oC
package type
64 QFP
2.5
Conducted susceptibility, electrical
fast transient/burst (EFT/B)
32768 Hz
crystal
2 MHz Bus
VCS_EFT
kV
3.0
> 3.0
1
2
Data based on qualification test results. Not tested in production.
The RESET pin is susceptible to the minimum applied transient of 220 V. All other pins have a result of A up to a minimum of
2000V.
The susceptibility performance classification is described in Table A-19.
Table A-19. Susceptibility Performance Classification
Result
Performance Criteria
A
B
No failure
The MCU performs as designed during and after exposure.
Self-recovering The MCU does not perform as designed during exposure. The MCU returns
failure
automatically to normal operation after exposure is removed.
C
D
E
Soft failure
The MCU does not perform as designed during exposure. The MCU does not return to
normal operation until exposure is removed and the RESET pin is asserted.
Hard failure
Damage
The MCU does not perform as designed during exposure. The MCU does not return to
normal operation until exposure is removed and the power to the MCU is cycled.
The MCU does not perform as designed during and after exposure. The MCU cannot
be returned to proper operation due to physical damage or other permanent
performance degradation.
MC9S08AW60 Data Sheet, Rev 2
308
Freescale Semiconductor
Appendix B
Ordering Information and Mechanical Drawings
B.1
Ordering Information
This section contains ordering numbers for MC9S08AW60 Series devices. See below for an example of
the device numbering system.
Table B-1. Consumer and Industrial Device Numbering System
Memory
Available Packages2
Type
Device Number1
FLASH
RAM
MC9S08AW60
MC9S08AW48
MC9S08AW32
63,280
49,152
32,768
64-pin LQFP
64-pin QFP
48-pin QFN
44-pin LQFP
2048
1024
MC9S08AW16
16,384
1
2
See Table 1-1 for a complete description of modules included on each device.
See Table B-3 for package information.
Table B-2. Automotive Device Numbering System
Memory
Available Packages2
Device Number1
FLASH
RAM
Type
S9S08AW60
S9S08AW48
S9S08AW32
63,280
49,152
32,768
64-pin LQFP
48-pin QFN
44-pin LQFP
2048
48-pin QFN
44-pin LQFP
S9S08AW16
16,384
1024
1
2
See Table 1-1 for a complete description of modules included on each device.
See Table B-3 for package information.
MC9S08AW60 Data Sheet, Rev 2
Freescale Semiconductor
309
Appendix B Ordering Information and Mechanical Drawings
B.2
Orderable Part Numbering System
B.2.1
Consumer and Industrial Orderable Part Numbering System
MC 9 S08 AW 60 C XX E
Pb free indicator
Package designator (See Table B-3)
Status (MC =Consumer &
Industrial Fully Qualified)
Memory
Temperature range
(C = –40°C to 85°C)
(M = –40°C to 125°C)
(9 = FLASH-based)
Core
Family
Memory size designator
B.2.2
Automotive Orderable Part Numbering System
S
9 S08 AW 60 C XX E
Pb free indicator
Package designator (See Table B-3)
Status (S = Automotive
Fully Qualified)
Memory
Temperature range
(C = –40°C to 85°C)
(V = –40°C to 105°C)
(M = –40°C to 125°C)
(9 = FLASH-based)
Core
Family
Memory size designator
B.3
Mechanical Drawings
This following pages contain mechanical specifications for MC9S08AW60 Series package options. See
Table B-3 for the document numbers that correspond to each package type.
Table B-3. Package Information
Pin Count
Type
Designator
Document No.
44
48
64
64
LQFP
QFN
FG
FD
PU
FU
98ASS23225W
98ARH99048A
98ASS23234W
98ASB42844B
LQFP
QFP
MC9S08AW60 Data Sheet, Rev 2
310
Freescale Semiconductor
Information in this document is provided solely to enable system and software implementers to use
Freescale Semiconductor products. There are no express or implied copyright licenses granted
hereunder to design or fabricate any integrated circuits or integrated circuits based on the information
in this document.
How to Reach Us:
USA/Europe/Locations not listed:
Freescale Semiconductor Literature Distribution
P.O. Box 5405, Denver, Colorado 80217
1-800-521-6274 or 480-768-2130
Freescale Semiconductor reserves the right to make changes without further notice to any products
herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages. “Typical” parameters
which may be provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating parameters,
including “Typicals” must be validated for each customer application by customer’s technical experts.
Freescale Semiconductor does not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized for use as components
in systems intended for surgical implant into the body, or other applications intended to support or
sustain life, or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer purchase or use
Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall
indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney
fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was
negligent regarding the design or manufacture of the part.
Japan:
Freescale Semiconductor Japan Ltd.
SPS, Technical Information Center
3-20-1, Minami-Azabu
Minato-ku
Tokyo 106-8573, Japan
81-3-3440-3569
Asia/Pacific:
Freescale Semiconductor H.K. Ltd.
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T. Hong Kong
852-26668334
Learn More:
For more information about Freescale
Semiconductor products, please visit
http://www.freescale.com
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other
product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2005.
MC9S08AW60, Rev 2
12/2006
相关型号:
©2020 ICPDF网 联系我们和版权申明