CBTL06121AHF,518 [NXP]
CBTL06121 - Gen1 hex display multiplexer QFN 56-Pin;
| 型号： | CBTL06121AHF,518 |
| 厂家： | 
NXP |
| 描述： | CBTL06121 - Gen1 hex display multiplexer QFN 56-Pin |
| 文件： | 总20页 (文件大小：159K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CBTL06121
Gen1 hex display multiplexer
Rev. 2 — 26 October 2010
Product data sheet
1. General description
The CBTL06121 is a six-channel (‘hex’) multiplexer for DisplayPort and PCI Express
applications at Generation 1 (‘Gen1’) speeds. It provides four differential channels
capable of switching or multiplexing (bidirectional and AC-coupled) PCI Express or
DisplayPort signals, using high-bandwidth pass-gate technology. Additionally, it provides
for switching/multiplexing of the Hot Plug Detect signal as well as the AUX or DDC (Direct
Display Control) signals, for a total of six channels.
The CBTL06121 is designed for Gen1 speeds, at 2.5 Gbit/s for PCI Express or 2.7 Gbit/s
for DisplayPort. The device is available in two different pinouts (A and B, orderable as
separate part numbers) to suit different motherboard layout requirements.
The typical application of CBTL06121 is on motherboards, docking stations or add-in
cards where the graphics and I/O system controller chip utilizes I/O pins that are
configurable for either PCI Express or DisplayPort operation. The hex display MUX can be
used in such applications to route the signal from the controller chip to either a physical
DisplayPort connector or a PCI Express connector using its 1 : 2 multiplexer topology. The
controller chip selects which path to use by setting a select signal (which can be latched)
HIGH or LOW.
Optionally, the hex MUX device can be used in conjunction with an HDMI/DVI level shifter
device (PTN3300A, PTN3300B or PTN3301) to allow for DisplayPort as well as HDMI/DVI
connectivity.
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
MULTI-MODE
DISPLAY SOURCE
CBTL06121
4
4
DisplayPort
connector
DP
PEG
HPD
AUX
4
docking connector
DisplayPort
REPEATER
DisplayPort
connector
002aad089
Fig 1. Intended usage 1: DisplayPort docking solution for mobile platform
MULTI-MODE
DISPLAY SOURCE
CBTL06121
4
HDMI/DVI
4
PTN3300
or
HDMI/DVI
connector
PTN3301
PEG
HPD
DDC
4
docking connector
dock
PTN3300 or
PTN3301
HDMI/DVI
connector
002aad090
Fig 2. Intended usage 2: HDMI/DVI docking solution for mobile platform
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
2 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
DDC
MULTI-MODE
DISPLAY SOURCE
CBTL06121
DP/HDMI/
DVI/PEG
4
DP/
HDMI/
DVI
connector
4
PTN3300
or
PTN3301
PEG
HPD/PEG RX
AUX/PEG RX
4
x16 PEG connector
002aad091
Fig 3. Intended usage 3: Digital display + external graphics solution for desktop
platform
2. Features and benefits
1 : 2 multiplexing of DisplayPort (v1.1 - 2.7 Gbit/s) or PCI Express (v1.1 - 2.5 Gbit/s)
signals
4 high-speed differential channels
1 channel for AUX differential signals or DDC clock and data
1 channel for HPD
High-bandwidth analog pass-gate technology
Very low intra-pair differential skew (< 5 ps)
Very low inter-pair skew (< 180 ps)
All path delays matched including between RX1− to X− and RX1+ to X+
Switch/MUX position select with latch function
Shutdown mode CMOS input
Shutdown mode minimizes power consumption while switching all channels off
Very low operation current of 0.2 mA typ
Very low shutdown current of < 10 μA
Standby mode minimizes power consumption while switching all channels off
Single 3.3 V power supply
ESD 8 kV HBM, 1 kV CDM
Two pinouts (A and B) available as separate ordering part numbers
Available in 11 mm × 5 mm HWQFN56R package
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
3 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
3. Applications
Motherboard applications requiring DisplayPort and PCI Express
switching/multiplexing
Docking stations
Notebook computers
Chip sets requiring flexible allocation of PCI Express or DisplayPort I/O pins to board
connectors
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
CBTL06121AHF[1][2]
CBTL06121BHF[1][2]
HWQFN56R plastic thermal enhanced very very thin quad flat package; no leads; SOT1033-1
56 terminals; resin based; body 11 × 5 × 0.7 mm[3]
[1] The A and B suffix in the part number correspond to the A and B pinouts, respectively (see Figure 5 and Figure 6).
[2] HF is the package designator for the HWQFN package.
[3] Total height after printed circuit board mounting = 0.8 mm (max.).
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
4 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
5. Functional diagram
MULTI-MODE
DISPLAY SOURCE
SEL
CBTL06121
MUX
LOGIC
LE_N
XSD
PCIe PHY
ELECTRICAL
PCIe
output buffer
AC-coupled
differential pair
D0+
IN_0+
D0−
DATA LANE
IN_0−
TX
TX0+
TX0−
PCIe
output buffer
AC-coupled
differential pair
D1+
IN_1+
D1−
DATA LANE
IN_1−
TX
TX1+
TX1−
PCIe
output buffer
AC-coupled
differential pair
D2+
IN_2+
D2−
DATA LANE
IN_2−
TX
TX2+
TX2−
PCIe
output buffer
AC-coupled
differential pair
D3+
IN_3+
D3−
DATA LANE
IN_3−
TX
TX3+
TX3−
HPD
X+
PCIe
input buffer
RX1+
X− to RX1− path matches
X+ to RX1+ path
RX
SPARE
X−
RX1−
PCIe
input buffer
AUX+
OUT+
AUX−
AUX DATA
OUT−
RX
RX0+
RX0−
TX
PEG CONNECTOR
OR
DOCKING CONNECTOR
002aad092
Fig 4. Functional diagram
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
5 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
6. Pinning information
6.1 Pinning
terminal 1
index area
terminal 1
index area
GND
IN_0+
IN_0−
IN_1+
IN_1−
1
2
3
4
5
6
7
8
9
48 GND
47 TX2+
46 TX2−
45 TX3+
44 TX3−
43 D0+
42 D0−
41 D1+
40 D1−
39 D2+
38 D2−
37 D3+
36 D3−
35 GND
GND
1
2
3
4
5
6
7
8
9
48 GND
47 D2+
46 D2−
45 D3+
44 D3−
43 TX0+
42 TX0−
41 TX1+
40 TX1−
SEL
LE_N
IN_0+
IN_0−
V
DD
V
DD
IN_2+
IN_2−
IN_3+
IN_1+
IN_1−
IN_2+
IN_3− 10
GND 11
OUT+ 12
OUT− 13
X+ 14
IN_2− 10
GND 11
IN_3+ 12
IN_3− 13
OUT+ 14
OUT− 15
GND 16
39 TX2+
CBTL06121AHF
CBTL06121BHF
38 TX2−
A pinout
B pinout
37 TX3+
36 TX3−
35 GND
X− 15
34
V
DD
34
V
DD
GND 16
33 RX0+
32 RX0−
31 RX1+
30 RX1−
29 GND
33 AUX+
32 AUX−
31 HPD
V
DD
17
V
DD
17
SEL 18
LE_N 19
GND 20
X+ 18
X− 19
30 SPARE
29 GND
GND 20
Transparent top view
Transparent top view
002aad655
002aad656
Fig 5. Pin configuration for HWQFN56R, A pinout
Fig 6. Pin configuration for HWQFN56R, B pinout
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
6 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
6.2 Pin description
Table 2.
Symbol
Pin description
Pin
Type
Description
Pinout A Pinout B
SEL
18
19
50
2
3.3 V low-voltage CMOS
single-ended input
SEL controls the MUX through a flow-through latch.
The latch gate is controlled by LE_N.
LE_N
XSD
3
3.3 V low-voltage CMOS
single-ended input
50
3.3 V low-voltage CMOS
single-ended input
Optional shutdown pin. Should be driven HIGH or
connected to VDD for normal operation. When LOW, all
paths are switched off (non-conducting) and supply current
consumption is minimized.
RX0+
RX0−
RX1+
RX1−
33
32
31
30
26
25
24
23
differential input
differential input
differential input
differential input
Differential input from PCIe connector or device. RX0+
makes a differential pair with RX0−. RX0+ is passed
through to the OUT+ pin when SEL = 0.
Differential input from PCIe connector or device. RX0−
makes a differential pair with RX0+. RX0− is passed
through to the OUT− pin when SEL = 0.
Differential input from PCIe connector or device. RX1+
makes a differential pair with RX1−. RX1+ is passed
through to the X+ pin when SEL = 0.
Differential input from PCIe connector or device. RX1−
makes a differential pair with RX1+. RX1− is passed
through to the X− pin on a path that matches the RX1+ to
X+ path.
IN_0+
IN_0−
IN_1+
IN_1−
IN_2+
IN_2−
IN_3+
IN_3−
HPD
2
4
differential input
differential input
differential input
differential input
differential input
differential input
differential input
differential input
Differential input from display source PCIe outputs.
IN_0+ makes a differential pair with IN_0−.
3
5
Differential input from display source PCIe outputs.
IN_0− makes a differential pair with IN_0+.
4
7
Differential input from display source PCIe outputs.
IN_1+ makes a differential pair with IN_1−.
5
8
Differential input from display source PCIe outputs.
IN_1− makes a differential pair with IN_1+.
7
9
Differential input from display source PCIe outputs.
IN_2+ makes a differential pair with IN_2−.
8
10
12
13
31
Differential input from display source PCIe outputs.
IN_2− makes a differential pair with IN_2+.
9
Differential input from display source PCIe outputs.
IN_3+ makes a differential pair with IN_3−.
10
24
Differential input from display source PCIe outputs.
IN_3− makes a differential pair with IN_3+.
high-voltage
single-ended input
Low frequency, 0 V to 5 V/3.3 V (nominal) input signal. This
signal comes from the HDMI/DP connector. Voltage HIGH
indicates a ‘plugged’ state; voltage LOW indicates
‘unplugged’.
X+
14
18
(SEL = HIGH); HPD:
Low frequency, 0 V to 5 V/3.3 V (nominal) input signal. This
high-voltage single-ended signal comes from the HDMI/DP connector.
input
(SEL = LOW); X+:
Analog ‘pass-through’ output corresponding to RX1+.
pass-through output
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
7 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
Table 2.
Symbol
Pin description …continued
Pin
Type
Description
Pinout A Pinout B
X−
15
19
pass-through output
from RX1− input
X− is an analog ‘pass-through’ output corresponding to the
RX1− input. The path from RX1− to X− is matched with the
path from RX1+ to X+. X+ and X− form a differential pair
when the pass-through MUX mode is selected.
D0+
43
42
41
40
39
38
37
36
54
53
52
51
47
46
45
44
54
53
52
51
47
46
45
44
43
42
41
40
39
38
37
36
pass-through output 1,
option 1
Analog ‘pass-through’ output 1 corresponding to IN_0+ and
IN_0−, when SEL = 1.
D0−
D1+
pass-through output 2,
option 1
Analog ‘pass-through’ output 1 corresponding to IN_1+ and
IN_1−, when SEL = 1.
D1−
D2+
pass-through output 3,
option 1
Analog ‘pass-through’ output 1 corresponding to IN_2+ and
IN_2−, when SEL = 1.
D2−
D3+
pass-through output 4,
option 1
Analog ‘pass-through’ output 1 corresponding to IN_3+ and
IN_3−, when SEL = 1.
D3−
TX0+
TX0−
TX1+
TX1−
TX2+
TX2−
TX3+
TX3−
VDD
pass-through output 1,
option 2
Analog ‘pass-through’ output 2 corresponding to IN_0+ and
IN_0−, when SEL = 0.
pass-through output 2,
option 2
Analog ‘pass-through’ output 2 corresponding to IN_1+ and
IN_1−, when SEL = 0.
pass-through output 3,
option 2
Analog ‘pass-through’ output 2 corresponding to IN_2+ and
IN_2−, when SEL = 0.
pass-through output 4,
option 2
Analog ‘pass-through’ output 2 corresponding to IN_3+ and
IN_3−, when SEL = 0.
6, 17, 22, 6, 17, 22, 3.3 V supply
Supply voltage (3.3 V ± 10 %).
27, 34,
55
27, 34,
55
AUX+
AUX−
OUT+
OUT−
GND[1]
26
25
12
13
33
32
14
15
differential input
differential input
differential input
differential input
High-speed differential pair for AUX signals.
High-speed differential pair for PCIe RX0+ signal.
High-speed differential pair for PCIe RX0− signal.
Ground.
1, 11, 16, 1, 11, 16, supply ground
20, 21,
28, 29,
35, 48,
49, 56
20, 21,
28, 29,
35, 48,
49, 56
SPARE
23
30
single-ended input
Spare channel for general-purpose switch use.
Connected to pin X− when SEL = 1.
[1] HWQFN56R package die supply ground is connected to both GND pins and exposed center pad. GND pins must be connected to
supply ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be
soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias
need to be incorporated in the PCB in the thermal pad region.
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
8 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
7. Functional description
Refer to Figure 4 “Functional diagram”.
The CBTL06121 uses 3.3 V power supply. All signal paths are implemented using
high-bandwidth pass-gate technology, are bidirectional and no clock or reset signal is
needed for the multiplexer to function.
The switch position is selected using the select signal (SEL), which can be latched using
the latch enable pin (LE_N). The detailed operation is described in Section 7.1.
7.1 MUX select (SEL) function
The internal multiplexer switch position is controlled by two logic inputs SEL and LE_N as
described below.
Table 3.
MUX select control
Dx
SEL
0
TXx; RXx
high-impedance
active; follows IN_x
active; follows IN_x
high-impedance
1
The switch position select input signal SEL controls the MUX through a flow-through latch,
which is gated by the latch enable input signal LE_N (active LOW). The latch is open
when LE_N is LOW; in this state the internal switch position will respond to the state of the
SEL input signal. The latch is closed when LE_N is HIGH, and the switch position will not
respond to input state changes on the SEL input.
Table 4.
MUX select latch control
Internal MUX select
responds to changes on SEL
latched
LE_N
0
1
Dx+
IN_x+
TXx+
Dx−
TXx−
IN_x−
internal
MUX select
TRANSPARENT
LATCH
SEL
LE_N
002aad088
Fig 7. MUX select function
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
9 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
7.2 Shutdown function
The CBTL06121 provides a shutdown function to minimize power consumption when the
application is not active but power to the CBTL06121 is provided. Pin XSD (active LOW)
puts all channels in off mode (non-conducting) while reducing current consumption to
near-zero.
Table 5.
Shutdown function
State
XSD
0
1
shutdown
active
8. Limiting values
Table 6.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
VDD
Parameter
Conditions
Min
−0.3
−40
Max
+5
Unit
V
supply voltage
case temperature
Tcase
for operation within
specification
+85
°C
[1]
[2]
Vesd
electrostatic discharge
voltage
HBM
CDM
-
-
8000
1000
V
V
[1] Human Body Model: ANSI/EOS/ESD-S5.1-1994, standard for ESD sensitivity testing, Human Body Model -
Component level; Electrostatic Discharge Association, Rome, NY, USA.
[2] Charged Device Model: ANSI/EOS/ESD-S5.3-1-1999, standard for ESD sensitivity testing, Charged Device
Model - Component level; Electrostatic Discharge Association, Rome, NY, USA.
9. Recommended operating conditions
Table 7.
Recommended operating conditions
Conditions
Symbol Parameter
Min
3.0
-
Typ
Max
3.6
Unit
V
VDD
VI
supply voltage
input voltage
3.3
-
-
3.6
V
Tamb
ambient temperature operating in free air
−40
+85
°C
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
10 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
10. Characteristics
10.1 General characteristics
Table 8.
General characteristics
Symbol Parameter
Conditions
Min
Typ
Max
1
Unit
mA
μA
IDD
supply current
operating mode (XSD = HIGH); VDD = 3.3 V
shutdown mode (XSD = LOW); VDD = 3.3 V
-
-
-
-
0.2
-
-
-
10
5
Ptot
total power consumption operating mode (XSD = HIGH); VDD = 3.3 V
mW
ms
tstartup
start-up time
supply voltage valid or XSD going HIGH to
channel specified operating characteristics
1
trcfg
reconfiguration time
SEL state change to channel specified
operating characteristics
-
-
1
ms
10.2 DisplayPort channel characteristics
Table 9.
DisplayPort channel characteristics
Symbol Parameter
Conditions
Min
−0.3
0
Typ
Max
+2.6
2.0
+1.2
-
Unit
V
VI
input voltage
-
VIC
VID
DDIL
common-mode input voltage
differential input voltage
differential insertion loss
-
V
−1.2
−2.5
−4.5
-
-
V
channel is on; 0 Hz ≤ f ≤ 1.0 GHz
channel is on; f = 2.5 GHz
−1.6
dB
dB
dB
dB
dB
-
-
-
-
-
channel is off; 0 Hz ≤ f ≤ 3.0 GHz
channel is on; 0 Hz ≤ f ≤ 1.0 GHz
−20
−10
−30
DDRL
differential return loss
-
DDNEXT differential near-end crosstalk adjacent channels are on;
-
0 Hz ≤ f ≤ 1.0 GHz
B
bandwidth
−3.0 dB intercept
-
-
2.5
-
-
GHz
ps
tPD
propagation delay
from left-side port to right-side port
or vice versa
180
tsk(dif)
tsk
differential skew time
skew time
intra-pair
inter-pair
-
-
-
-
5
ps
ps
180
10.3 AUX and DDC ports
Table 10. AUX and DDC port characteristics
Symbol
VI
Parameter
Conditions
DDC or AUX
DDC or AUX
Min
−0.3
0
Typ
Max
+2.6
2.0
+1.2
-
Unit
V
input voltage
-
VIC
common-mode input voltage
differential input voltage
propagation delay
-
V
VID
−1.2
-
-
V
[1]
tPD
from left-side port to right-side port
or vice versa
180
ps
[1] Time from DDC/AUX input changing state to AUX output changing state. Includes DDC/AUX rise/fall time.
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
11 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
10.4 HPD input, HPD output
Table 11. HPD input and output characteristics
Symbol
VI
Parameter
Conditions
Min
−0.3
-
Typ
-
Max
3.6
-
Unit
V
[1]
[2]
input voltage
propagation delay
tPD
from HPD_SINK to HPD_SOURCE
180
ps
[1] Low-speed input changes state on cable plug/unplug.
[2] Time from HPD_IN changing state to HPD changing state. Includes HPD rise/fall time.
10.5 MUX select and latch input
Table 12. SEL, LE_N input characteristics
Symbol
VIH
Parameter
Conditions
Min
2.0
0
Typ
Max
3.6
0.8
10
Unit
V
HIGH-level input voltage
LOW-level input voltage
input leakage current
-
-
-
VIL
V
ILI
measured with input at
VIH(max) and VIL(min)
-
μA
11. Test information
11.1 Switch test fixture requirements
The test fixture for switch S-parameter measurement shall be designed and built to
specific requirements, as described below, to ensure good measurement quality and
consistency.
• The test fixture shall be a FR4-based PCB of the microstrip structure; the dielectric
thickness or stack-up shall be about 4 mils.
• The total thickness of the test fixture PCB shall be 1.57 mm (0.62 in).
• The measurement signals shall be launched into the switch from the top of the test
fixture, capturing the through-hole stub effect.
• Traces between the DUT and measurement ports (SMA or microprobe) should be
uncoupled from each other, as much as possible. Therefore, the traces should be
routed in such a way that traces will diverge from each other exiting from the switch
pin field.
• The trace lengths between the DUT and measurement port shall be minimized. The
maximum trace length shall not exceed 1000 mils. The trace lengths between the
DUT and measurement port shall be equal.
• All of the traces on the test board and add-in card must be held to a characteristic
impedance of 50 Ω with a tolerance of ±7 %.
• SMA connector is recommended for ease of use. The SMA launch structure shall be
designed to minimize the connection discontinuity from SMA to the trace. The
impedance range of the SMA seen from a TDR with a 60 ps rise time should be
within 50 Ω ± 7 Ω.
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
12 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
12. Package outline
HWQFN56R: plastic thermal enhanced very very thin quad flat package; no leads;
56 terminals; resin based; body 11 x 5 x 0.7 mm
SOT1033-1
D
B
A
terminal 1
index area
E
A
detail X
e
1
e
1/2 e
C
M
M
v
w
C A
C
B
b
L
1
y
1
y
L
C
21
28
29
20
e
E
h
e
2
1/2 e
48
1
56
49
D
h
X
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
b
D
D
h
E
E
e
e
1
e
2
L
L
v
w
y
y
1
h
1
max
0.27
0.23
5.1
4.9
2.5
2.3
11.1
10.9
8.5
8.3
0.42
0.38
0.1
0.0
mm
0.8
0.5
3.5
9.5
0.1
0.05 0.05
0.1
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
- - -
JEDEC
JEITA
07-09-19
07-12-01
- - -
- - -
SOT1033-1
Fig 8. Package outline HWQFN56R (SOT1033-1)
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
13 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
13. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
13.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
13.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
• Board specifications, including the board finish, solder masks and vias
• Package footprints, including solder thieves and orientation
• The moisture sensitivity level of the packages
• Package placement
• Inspection and repair
• Lead-free soldering versus SnPb soldering
13.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
14 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
13.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 9) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 13 and 14
Table 13. SnPb eutectic process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
235
≥ 350
220
< 2.5
≥ 2.5
220
220
Table 14. Lead-free process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
260
350 to 2000
> 2000
260
< 1.6
260
250
245
1.6 to 2.5
> 2.5
260
245
250
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 9.
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
15 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 9. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
14. Abbreviations
Table 15. Abbreviations
Acronym
AUX
CDM
CMOS
DDC
DP
Description
Auxiliary channel in DisplayPort definition
Charged-Device Model
Complementary Metal-Oxide Semiconductor
Direct Display Control
DisplayPort
DUT
DVI
Device Under Test
Digital Video Interface
ElectroStatic Discharge
Human Body Model
ESD
HBM
HDMI
HPD
I/O
High-Definition Multimedia Interface
Hot Plug Detect
Input/Output
MUX
PCB
PCI
Multiplexer
Printed-Circuit Board
Peripheral Component Interconnect
PCI Express
PCIe
PEG
SMA
TDR
PCI Express Graphics
SubMiniature, version A (connector)
Time-Domain Reflectometry
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
16 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
15. Revision history
Table 16. Revision history
Document ID
CBTL06121 v.2
Modifications:
CBTL06121 v.1
Release date
20101026
Data sheet status
Change notice
Supersedes
Product data sheet
-
CBTL06121 v.1
• Table 9 row B (bandwidth): typical value corrected from 25 to 2.5
20080523 Product data sheet
-
-
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
17 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
malfunction of an NXP Semiconductors product can reasonably be expected
16.2 Definitions
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
16.3 Disclaimers
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
18 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
CBTL06121
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
19 of 20
CBTL06121
NXP Semiconductors
Gen1 hex display multiplexer
18. Contents
1
2
3
4
5
General description. . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ordering information. . . . . . . . . . . . . . . . . . . . . 4
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 5
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 6
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 7
7
7.1
7.2
Functional description . . . . . . . . . . . . . . . . . . . 9
MUX select (SEL) function . . . . . . . . . . . . . . . . 9
Shutdown function . . . . . . . . . . . . . . . . . . . . . 10
8
9
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 10
Recommended operating conditions. . . . . . . 10
10
Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . 11
General characteristics. . . . . . . . . . . . . . . . . . 11
DisplayPort channel characteristics . . . . . . . . 11
AUX and DDC ports . . . . . . . . . . . . . . . . . . . . 11
HPD input, HPD output. . . . . . . . . . . . . . . . . . 12
MUX select and latch input. . . . . . . . . . . . . . . 12
10.1
10.2
10.3
10.4
10.5
11
11.1
12
Test information. . . . . . . . . . . . . . . . . . . . . . . . 12
Switch test fixture requirements . . . . . . . . . . . 12
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 13
13
Soldering of SMD packages . . . . . . . . . . . . . . 14
Introduction to soldering . . . . . . . . . . . . . . . . . 14
Wave and reflow soldering . . . . . . . . . . . . . . . 14
Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 14
Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . 15
13.1
13.2
13.3
13.4
14
15
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 16
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 17
16
Legal information. . . . . . . . . . . . . . . . . . . . . . . 18
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 18
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16.1
16.2
16.3
16.4
17
18
Contact information. . . . . . . . . . . . . . . . . . . . . 19
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2010.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 26 October 2010
Document identifier: CBTL06121
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明