KMPC860TCZQ66D4_技术文档

MPC860EC

Rev. 9, 02/2012

Freescale Semiconductor

Technical Data

MPC860 PowerQUICC Family

Hardware Specifications

Contents

This hardware specification contains detailed information on

1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3. Maximum Tolerated Ratings . . . . . . . . . . . . . . . . . . . 7

4. Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . 8

5. Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6. DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7. Thermal Calculation and Measurement . . . . . . . . . . 12

8. Layout Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

9. Bus Signal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 15

10. IEEE 1149.1 Electrical Specifications . . . . . . . . . . . 41

11. CPM Electrical Characteristics . . . . . . . . . . . . . . . . . 43

12. UTOPIA AC Electrical Specifications . . . . . . . . . . . 65

13. FEC Electrical Characteristics . . . . . . . . . . . . . . . . . 67

14. Mechanical Data and Ordering Information . . . . . . . 70

15. Document Revision History . . . . . . . . . . . . . . . . . . . 76

power considerations, DC/AC electrical characteristics, and

AC timing specifications for the MPC860 family.

To locate published errata or updates for this document, see

the MPC860 product summary page on the website listed on

the back cover of this document or contact your local

Freescale sales office.

Freescale reserves the right to change the detail specifications as may be required

to permit improvements in the design of its products.

Overview

1 Overview

The MPC860 power quad integrated communications controller (PowerQUICC™) is a versatile one-chip

integrated microprocessor and peripheral combination designed for a variety of controller applications. It

particularly excels in communications and networking systems. The PowerQUICC unit is referred to as

the MPC860 in this hardware specification.

The MPC860 implements Power Architecture™ technology and contains a superset of Freescale’s

MC68360 quad integrated communications controller (QUICC), referred to here as the QUICC, RISC

communications proccessor module (CPM). The CPU on the MPC860 is a 32-bit core built on Power

Architecture technology that incorporates memory management units (MMUs) and instruction and data

caches.. The CPM from the MC68360 QUICC has been enhanced by the addition of the inter-integrated

2

controller (I C) channel. The memory controller has been enhanced, enabling the MPC860 to support any

type of memory, including high-performance memories and new types of DRAMs. A PCMCIA socket

controller supports up to two sockets. A real-time clock has also been integrated.

Table 1 shows the functionality supported by the MPC860 family.

Table 1. MPC860 Family Functionality

Cache (Kbytes)

Ethernet

1

Part

ATM

SCC

Reference

Instruction

Cache

Data Cache

10T

10/100

MPC860DE

MPC860DT

MPC860DP

MPC860EN

MPC860SR

MPC860T

4

8

4

8

4

Up to 2

Up to 4

1

—

1

—

2

4

1

2

Yes

—

16

4

1

—

1

4

Yes

4

MPC860P

MPC855T

16

4

1

Supporting documentation for these devices refers to the following:

1. MPC860 PowerQUICC Family User’s Manual (MPC860UM, Rev. 3)

2. MPC855T User’s Manual (MPC855TUM, Rev. 1)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

2

Freescale Semiconductor

Features

2 Features

The following list summarizes the key MPC860 features:

•

Embedded single-issue, 32-bit core (implementing the Power Architecture technology) with

thirty-two 32-bit general-purpose registers (GPRs)

— The core performs branch prediction with conditional prefetch without conditional execution.

— 4- or 8-Kbyte data cache and 4- or 16-Kbyte instruction cache (see Table 1)

– 16-Kbyte instruction caches are four-way, set-associative with 256 sets; 4-Kbyte instruction

caches are two-way, set-associative with 128 sets.

– 8-Kbyte data caches are two-way, set-associative with 256 sets; 4-Kbyte data caches are

two-way, set-associative with 128 sets.

– Cache coherency for both instruction and data caches is maintained on 128-bit (4-word)

cache blocks.

– Caches are physically addressed, implement a least recently used (LRU) replacement

algorithm, and are lockable on a cache block basis.

— MMUs with 32-entry TLB, fully-associative instruction, and data TLBs

— MMUs support multiple page sizes of 4-, 16-, and 512-Kbytes, and 8-Mbytes; 16 virtual

address spaces and 16 protection groups

— Advanced on-chip-emulation debug mode

Up to 32-bit data bus (dynamic bus sizing for 8, 16, and 32 bits)

32 address lines

•

Operates at up to 80 MHz

Memory controller (eight banks)

— Contains complete dynamic RAM (DRAM) controller

— Each bank can be a chip select or RAS to support a DRAM bank.

— Up to 15 wait states programmable per memory bank

— Glueless interface to DRAM, SIMMS, SRAM, EPROM, Flash EPROM, and other memory

devices

— DRAM controller programmable to support most size and speed memory interfaces

— Four CAS lines, four WE lines, and one OE line

— Boot chip-select available at reset (options for 8-, 16-, or 32-bit memory)

— Variable block sizes (32 Kbytes to 256 Mbytes)

— Selectable write protection

— On-chip bus arbitration logic

•

General-purpose timers

— Four 16-bit timers or two 32-bit timers

— Gate mode can enable/disable counting

— Interrupt can be masked on reference match and event capture.

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

3

Features

•

System integration unit (SIU)

— Bus monitor

— Software watchdog

— Periodic interrupt timer (PIT)

— Low-power stop mode

— Clock synthesizer

— Decrementer, time base, and real-time clock (RTC)

— Reset controller

— IEEE 1149.1™ Std. test access port (JTAG)

Interrupts

•

— Seven external interrupt request (IRQ) lines

— 12 port pins with interrupt capability

— 23 internal interrupt sources

— Programmable priority between SCCs

— Programmable highest priority request

•

10/100 Mbps Ethernet support, fully compliant with the IEEE 802.3u® Standard (not available

when using ATM over UTOPIA interface)

ATM support compliant with ATM forum UNI 4.0 specification

— Cell processing up to 50–70 Mbps at 50-MHz system clock

— Cell multiplexing/demultiplexing

— Support of AAL5 and AAL0 protocols on a per-VC basis. AAL0 support enables OAM and

software implementation of other protocols.

— ATM pace control (APC) scheduler, providing direct support for constant bit rate (CBR) and

unspecified bit rate (UBR) and providing control mechanisms enabling software support of

available bit rate (ABR)

— Physical interface support for UTOPIA (10/100-Mbps is not supported with this interface) and

byte-aligned serial (for example, T1/E1/ADSL)

— UTOPIA-mode ATM supports level-1 master with cell-level handshake, multi-PHY (up to four

physical layer devices), connection to 25-, 51-, or 155-Mbps framers, and UTOPIA/system

clock ratios of 1/2 or 1/3.

— Serial-mode ATM connection supports transmission convergence (TC) function for

T1/E1/ADSL lines, cell delineation, cell payload scrambling/descrambling, automatic

idle/unassigned cell insertion/stripping, header error control (HEC) generation, checking, and

statistics.

•

Communications processor module (CPM)

— RISC communications processor (CP)

— Communication-specific commands (for example, GRACEFUL STOP TRANSMIT, ENTER HUNT

MODE, and RESTART TRANSMIT)

— Supports continuous mode transmission and reception on all serial channels

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

4

Freescale Semiconductor

Features

— Up to 8 Kbytes of dual-port RAM

— 16 serial DMA (SDMA) channels

— Three parallel I/O registers with open-drain capability

Four baud-rate generators (BRGs)

•

— Independent (can be tied to any SCC or SMC)

— Allows changes during operation

— Autobaud support option

Four serial communications controllers (SCCs)

— Ethernet/IEEE 802.3® standard optional on SCC1–4, supporting full 10-Mbps operation

(available only on specially programmed devices)

— HDLC/SDLC (all channels supported at 2 Mbps)

— HDLC bus (implements an HDLC-based local area network (LAN))

— Asynchronous HDLC to support point-to-point protocol (PPP)

— AppleTalk

— Universal asynchronous receiver transmitter (UART)

— Synchronous UART

— Serial infrared (IrDA)

— Binary synchronous communication (BISYNC)

— Totally transparent (bit streams)

— Totally transparent (frame-based with optional cyclic redundancy check (CRC))

Two SMCs (serial management channels)

— UART

•

— Transparent

— General circuit interface (GCI) controller

— Can be connected to the time-division multiplexed (TDM) channels

One SPI (serial peripheral interface)

•

— Supports master and slave modes

— Supports multimaster operation on the same bus

2

One I C (inter-integrated circuit) port

— Supports master and slave modes

— Multiple-master environment support

Time-slot assigner (TSA)

— Allows SCCs and SMCs to run in multiplexed and/or non-multiplexed operation

— Supports T1, CEPT, PCM highway, ISDN basic rate, ISDN primary rate, user defined

— 1- or 8-bit resolution

— Allows independent transmit and receive routing, frame synchronization, and clocking

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

5

Features

— Allows dynamic changes

— Can be internally connected to six serial channels (four SCCs and two SMCs)

Parallel interface port (PIP)

•

— Centronics interface support

— Supports fast connection between compatible ports on the MPC860 or the MC68360

PCMCIA interface

— Master (socket) interface, release 2.1 compliant

— Supports two independent PCMCIA sockets

— Supports eight memory or I/O windows

Low power support

•

— Full on—all units fully powered

— Doze—core functional units disabled except time base decrementer, PLL, memory controller,

RTC, and CPM in low-power standby

— Sleep—all units disabled except RTC and PIT, PLL active for fast wake up

— Deep sleep—all units disabled including PLL except RTC and PIT

— Power down mode—all units powered down except PLL, RTC, PIT, time base, and

decrementer

•

Debug interface

— Eight comparators: four operate on instruction address, two operate on data address, and two

operate on data

— Supports conditions: = ≠ < >

— Each watchpoint can generate a break-point internally.

3.3-V operation with 5-V TTL compatibility except EXTAL and EXTCLK

357-pin ball grid array (BGA) package

•

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

6

Freescale Semiconductor

Maximum Tolerated Ratings

3 Maximum Tolerated Ratings

This section provides the maximum tolerated voltage and temperature ranges for the MPC860. Table 2

provides the maximum ratings.

This device contains circuitry protecting against damage due to high-static voltage or electrical fields;

however, it is advised that normal precautions be taken to avoid application of any voltages higher than

maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused

inputs are tied to an appropriate logic voltage level (for example, either GND or V ).

DD

Table 2. Maximum Tolerated Ratings

(GND = 0 V)

Rating

Symbol

Value

Unit

1

Supply voltage

V

–0.3 to 4.0

GND – 0.3 to V

0

V

DDH

V

DDL

KAPWR

V

DDSYN

2

Input voltage

V

in

DDH

3

Temperature (standard)

T

°C

A(min)

T

95

j(max)

3

Temperature (extended)

T

–40

A(min)

T

95

j(max)

Storage temperature range

T

–55 to 150

stg

1

2

The power supply of the device must start its ramp from 0.0 V.

Functional operating conditions are provided with the DC electrical specifications in Table 6. Absolute maximum ratings are

stress ratings only; functional operation at the maxima is not guaranteed. Stress beyond those listed may affect device

reliability or cause permanent damage to the device.

Caution: All inputs that tolerate 5 V cannot be more than 2.5 V greater than the supply voltage. This restriction applies to

power-up and normal operation (that is, if the MPC860 is unpowered, voltage greater than 2.5 V must not be applied to its

inputs).

3

Minimum temperatures are guaranteed as ambient temperature, T . Maximum temperatures are guaranteed as junction

A

temperature, T .

j

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

7

Thermal Characteristics

Figure 1 shows the undershoot and overshoot voltages at the interface of the MPC860.

V

/V

+ 20%

DDH DDL

V

/V

+ 5%

/V

DDH DDL

V

DDH DDL

IH

GND

GND – 0.3 V

V

IL

GND – 0.7 V

Not to Exceed 10%

1

of t

interface

Note:

1. t

refers to the clock period associated with the bus clock interface.

interface

Figure 1. Undershoot/Overshoot Voltage for V

and V

DDL

DDH

4 Thermal Characteristics

Table 3. Package Description

Package Designator

Package Code (Case No.)

Package Description

ZP

5050 (1103-01)

PBGA 357 25*25*0.9P1.27

PBGA 357 25*25*1.2P1.27

ZQ/VR

5058 (1103D-02)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

8

Freescale Semiconductor

Thermal Characteristics

Table 4 shows the thermal characteristics for the MPC860.

Table 4. MPC860 Thermal Resistance Data

ZP

ZQ / VR

Unit

Rating

Environment

Symbol

MPC860P MPC860P

Mold Compound Thickness

0.85

34

22

27

18

14

6

1.15

34

22

27

18

13

8

mm

1

2

Junction-to-ambient

Natural convection

Single-layer board (1s)

R

•C/W

θJA

3

Four-layer board (2s2p)

Single-layer board (1s)

Four-layer board (2s2p)

R

θJMA

Airflow (200 ft/min)

4

Junction-to-board

R

θJB

θJC

5

Junction-to-case

R

6

Junction-to-package top Natural convection

Ψ

2

JT

1

Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board)

temperature, ambient temperature, airflow, power dissipation of other components on the board, and board thermal

resistance.

Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board horizontal.

Per JEDEC JESD51-6 with the board horizontal.

Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured

on the top surface of the board near the package.

Indicates the average thermal resistance between the die and the case top surface as measured by the cold plate method

(MIL SPEC-883 Method 1012.1) with the cold plate temperature used for the case temperature. For exposed pad

packages where the pad would be expected to be soldered, junction-to-case thermal resistance is a simulated value from

the junction to the exposed pad without contact resistance.

2

3

4

5

6

Thermal characterization parameter indicating the temperature difference between the package top and the junction

temperature per JEDEC JESD51-2.

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

9

Power Dissipation

5 Power Dissipation

Table 5 provides power dissipation information. The modes are 1:1, where CPU and bus speeds are equal,

and 2:1, where CPU frequency is twice the bus speed.

Table 5. Power Dissipation (P )

D

1

2

Die Revision

Frequency (MHz)

Typical

Maximum

Unit

D.4

(1:1 mode)

50

66

80

656

TBD

722

851

735

TBD

762

909

mW

D.4

(2:1 mode)

1

2

Typical power dissipation is measured at 3.3 V.

Maximum power dissipation is measured at 3.5 V.

NOTE

Values in Table 5 represent V

-based power dissipation and do not

DDL

include I/O power dissipation over V

. I/O power dissipation varies

DDH

widely by application due to buffer current, depending on external circuitry.

6 DC Characteristics

Table 6 provides the DC electrical characteristics for the MPC860.

Table 6. DC Electrical Specifications

Characteristic

Symbol

, V , V

Min

Max

Unit

Operating voltage at 40 MHz or less

V

3.0

2.0

3.6

V

DDH

DDL DDSYN

KAPWR

(power-down mode)

KAPWR

(all other operating modes)

V

– 0.4

V

DDH

Operating voltage greater than 40 MHz

V

, V

, KAPWR,

DDL

3.135

2.0

3.465

DDH

V

DDSYN

KAPWR

(power-down mode)

3.6

KAPWR

(all other operating modes)

– 0.4

V

DDH

Input high voltage (all inputs except EXTAL and

EXTCLK)

V

2.0

5.5

0.8

IH

1

Input low voltage

V

GND

V

IL

EXTAL, EXTCLK input high voltage

V

0.7 × (V

)

V

+ 0.3

DDH

IHC

DDH

Input leakage current, V = 5.5 V (except TMS, TRST,

I

—

100

µA

in

DSCK, and DSDI pins)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

10

Freescale Semiconductor

DC Characteristics

Table 6. DC Electrical Specifications (continued)

Characteristic Symbol Min

Max

Unit

Input leakage current, V = 3.6 V (except TMS, TRST,

DSCK, and DSDI pins)

I

—

10

µA

in

In

Input leakage current, V = 0 V (except TMS, TRST,

µA

in

In

DSCK, and DSDI pins)

2

Input capacitance

C

—

20

—

pF

V

in

Output high voltage, I

= –2.0 mA, V

= 3.0 V

V

OH

2.4

OH

DDH

(except XTAL, XFC, and open-drain pins)

Output low voltage

V

—

0.5

V

OL

I

= 2.0 mA, CLKOUT

OL

3

= 3.2 mA

= 5.3 mA

4

= 7.0 mA, TXD1/PA14, TXD2/PA12

= 8.9 mA, TS, TA, TEA, BI, BB, HRESET, SRESET

1

2

V (max) for the I C interface is 0.8 V rather than the 1.5 V as specified in the I C standard.

IL

2

3

Input capacitance is periodically sampled.

A(0:31), TSIZ0/REG, TSIZ1, D(0:31), DP(0:3)/IRQ(3:6), RD/WR, BURST, RSV/IRQ2, IP_B(0:1)/IWP(0:1)/VFLS(0:1),

IP_B2/IOIS16_B/AT2, IP_B3/IWP2/VF2, IP_B4/LWP0/VF0, IP_B5/LWP1/VF1, IP_B6/DSDI/AT0, IP_B7/PTR/AT3,

RXD1/PA15, RXD2/PA13, L1TXDB/PA11, L1RXDB/PA10, L1TXDA/PA9, L1RXDA/PA8, TIN1/L1RCLKA/BRGO1/CLK1/PA7,

BRGCLK1/TOUT1/CLK2/PA6, TIN2/L1TCLKA/BRGO2/CLK3/PA5, TOUT2/CLK4/PA4, TIN3/BRGO3/CLK5/PA3, BRGCLK2/

L1RCLKB/TOUT3/CLK6/PA2, TIN4/BRGO4/CLK7/PA1, L1TCLKB/TOUT4/CLK8/PA0, REJCT1/SPISEL/PB31, SPICLK/

PB30,SPIMOSI/PB29, BRGO4/SPIMISO/PB28, BRGO1/I2CSDA/PB27, BRGO2/I2CSCL/PB26, SMTXD1/PB25, SMRXD1/

PB24, SMSYN1/SDACK1/PB23, SMSYN2/SDACK2/PB22, SMTXD2/L1CLKOB/PB21, SMRXD2/L1CLKOA/PB20, L1ST1/

RTS1/PB19, L1ST2/RTS2/PB18, L1ST3/L1RQB/PB17, L1ST4/L1RQA/PB16, BRGO3/PB15, RSTRT1/PB14, L1ST1/RTS1/

DREQ0/PC15, L1ST2/RTS2/DREQ1/PC14, L1ST3/L1RQB/PC13, L1ST4/L1RQA/PC12, CTS1/PC11, TGATE1/CD1/PC10,

CTS2/PC9, TGATE2/CD2/PC8, SDACK2/L1TSYNCB/PC7, L1RSYNCB/PC6, SDACK1/L1TSYNCA/PC5, L1RSYNCA/PC4,

PD15, PD14, PD13, PD12, PD11, PD10, PD9, PD8, PD5, PD6, PD7, PD4, PD3, MII_MDC, MII_TX_ER, MII_EN, MII_MDIO,

and MII_TXD[0:3]

4

BDIP/GPL_B(5), BR, BG, FRZ/IRQ6, CS(0:5), CS(6)/CE(1)_B, CS(7)/CE(2)_B, WE0/BS_B0/IORD, WE1/BS_B1/IOWR,

WE2/BS_B2/PCOE, WE3/BS_B3/PCWE, BS_A(0:3), GPL_A0/GPL_B0, OE/GPL_A1/GPL_B1, GPL_A(2:3)/GPL_B(2:3)/

CS(2:3), UPWAITA/GPL_A4, UPWAITB/GPL_B4, GPL_A5, ALE_A, CE1_A, CE2_A, ALE_B/DSCK/AT1, OP(0:1),

OP2/MODCK1/STS, OP3/MODCK2/DSDO, and BADDR(28:30)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

11

Thermal Calculation and Measurement

7 Thermal Calculation and Measurement

For the following discussions, P = (V × I ) + PI/O, where PI/O is the power dissipation of the I/O

D

DD

drivers.

7.1

Estimation with Junction-to-Ambient Thermal Resistance

An estimation of the chip junction temperature, T_J, in ºC can be obtained from the equation:

T = T + (R × P )

J

A

θJA

D

where:

T = ambient temperature (ºC)

A

R

= package junction-to-ambient thermal resistance (ºC/W)

θJA

P = power dissipation in package

D

The junction-to-ambient thermal resistance is an industry standard value which provides a quick and easy

estimation of thermal performance. However, the answer is only an estimate; test cases have demonstrated

that errors of a factor of two (in the quantity T – T ) are possible.

J

A

7.2

Estimation with Junction-to-Case Thermal Resistance

Historically, the thermal resistance has frequently been expressed as the sum of a junction-to-case thermal

resistance and a case-to-ambient thermal resistance:

R

= R

+ R

θJC θCA

θJA

where:

R

= junction-to-ambient thermal resistance (ºC/W)

= junction-to-case thermal resistance (ºC/W)

= case-to-ambient thermal resistance (ºC/W)

θJA

θJC

θCA

R

is device related and cannot be influenced by the user. The user adjusts the thermal environment to

θJC

affect the case-to-ambient thermal resistance, R

. For instance, the user can change the airflow around

θCA

the device, add a heat sink, change the mounting arrangement on the printed-circuit board, or change the

thermal dissipation on the printed-circuit board surrounding the device. This thermal model is most useful

for ceramic packages with heat sinks where some 90% of the heat flows through the case and the heat sink

to the ambient environment. For most packages, a better model is required.

7.3

Estimation with Junction-to-Board Thermal Resistance

A simple package thermal model which has demonstrated reasonable accuracy (about 20%) is a

two-resistor model consisting of a junction-to-board and a junction-to-case thermal resistance. The

junction-to-case thermal resistance covers the situation where a heat sink is used or where a substantial

amount of heat is dissipated from the top of the package. The junction-to-board thermal resistance

describes the thermal performance when most of the heat is conducted to the printed-circuit board. It has

been observed that the thermal performance of most plastic packages, especially PBGA packages, is

strongly dependent on the board temperature; see Figure 2.

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

12

Freescale Semiconductor

Thermal Calculation and Measurement

Board Temperature Rise Above Ambient Divided by Package Power

Figure 2. Effect of Board Temperature Rise on Thermal Behavior

If the board temperature is known, an estimate of the junction temperature in the environment can be made

using the following equation:

T = T + (R

× P )

D

J

B

θJB

where:

R

= junction-to-board thermal resistance (ºC/W)

θJB

T = board temperature (ºC)

B

P = power dissipation in package

D

If the board temperature is known and the heat loss from the package case to the air can be ignored,

acceptable predictions of junction temperature can be made. For this method to work, the board and board

mounting must be similar to the test board used to determine the junction-to-board thermal resistance,

namely a 2s2p (board with a power and a ground plane) and by attaching the thermal balls to the ground

plane.

7.4

Estimation Using Simulation

When the board temperature is not known, a thermal simulation of the application is needed. The simple

two-resistor model can be used with the thermal simulation of the application [2], or a more accurate and

complex model of the package can be used in the thermal simulation.

7.5

Experimental Determination

To determine the junction temperature of the device in the application after prototypes are available, the

thermal characterization parameter (Ψ ) can be used to determine the junction temperature with a

JT

measurement of the temperature at the top center of the package case using the following equation:

T = T + (Ψ × P )

J

T

JT

D

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

13

Layout Practices

where:

Ψ = thermal characterization parameter

JT

T = thermocouple temperature on top of package

T

P = power dissipation in package

D

The thermal characterization parameter is measured per JEDEC JESD51-2 specification using a 40 gauge

type T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned

so that the thermocouple junction rests on the package. A small amount of epoxy is placed over the

thermocouple junction and over 1 mm of wire extending from the junction. The thermocouple wire is

placed flat against the package case to avoid measurement errors caused by cooling effects of the

thermocouple wire.

7.6

References

Semiconductor Equipment and Materials International

(415) 964-5111

805 East Middlefield Rd.

Mountain View, CA 94043

MIL-SPEC and EIA/JESD (JEDEC) Specifications

(Available from Global Engineering Documents)

800-854-7179 or

303-397-7956

JEDEC Specifications

http://www.jedec.org

1. C.E. Triplett and B. Joiner, “An Experimental Characterization of a 272 PBGA Within an

Automotive Engine Controller Module,” Proceedings of SemiTherm, San Diego, 1998, pp. 47–54.

2. B. Joiner and V. Adams, “Measurement and Simulation of Junction to Board Thermal Resistance

and Its Application in Thermal Modeling,” Proceedings of SemiTherm, San Diego, 1999,

pp. 212–220.

8 Layout Practices

Each V_DDpin on the MPC860 should be provided with a low-impedance path to the board’s supply. Each

GND pin should likewise be provided with a low-impedance path to ground. The power supply pins drive

distinct groups of logic on the chip. The V_DDpower supply should be bypassed to ground using at least

four 0.1 µF-bypass capacitors located as close as possible to the four sides of the package. The capacitor

leads and associated printed circuit traces connecting to chip V_DDand GND should be kept to less than half

an inch per capacitor lead. A four-layer board employing two inner layers as V_CCand GND planes is

recommended.

All output pins on the MPC860 have fast rise and fall times. Printed circuit (PC) trace interconnection

length should be minimized in order to minimize undershoot and reflections caused by these fast output

switching times. This recommendation particularly applies to the address and data buses. Maximum PC

trace lengths of 6 inches are recommended. Capacitance calculations should consider all device loads as

well as parasitic capacitances due to the PC traces. Attention to proper PCB layout and bypassing becomes

especially critical in systems with higher capacitive loads because these loads create higher transient

currents in the V_CCand GND circuits. Pull up all unused inputs or signals that will be inputs during reset.

Special care should be taken to minimize the noise levels on the PLL supply pins.

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

14

Freescale Semiconductor

Bus Signal Timing

9 Bus Signal Timing

Table 7 provides the bus operation timing for the MPC860 at 33, 40, 50, and 66 MHz.

The maximum bus speed supported by the MPC860 is 66 MHz. Higher-speed parts must be operated in

half-speed bus mode (for example, an MPC860 used at 80 MHz must be configured for a 40-MHz bus).

The timing for the MPC860 bus shown assumes a 50-pF load for maximum delays and a 0-pF load for

minimum delays.

Table 7. Bus Operation Timings

33 MHz

Min Max

40 MHz

Min Max

50 MHz

Min Max

66 MHz

Min Max

Num

Characteristic

Unit

B1

CLKOUT period

30.30 30.30 25.00 30.30 20.00 30.30 15.15 30.30

–0.90 0.90 –0.90 0.90 –0.90 0.90 –0.90 0.90

ns

B1a EXTCLK to CLKOUT phase skew

(EXTCLK > 15 MHz and MF <= 2)

B1b EXTCLK to CLKOUT phase skew

(EXTCLK > 10 MHz and MF < 10)

–2.30 2.30 –2.30 2.30 –2.30 2.30 –2.30 2.30

–0.60 0.60 –0.60 0.60 –0.60 0.60 –0.60 0.60

–2.00 2.00 –2.00 2.00 –2.00 2.00 –2.00 2.00

ns

B1c CLKOUT phase jitter (EXTCLK > 15 MHz

1

and MF <= 2)

1

B1d CLKOUT phase jitter

ns

%

1

B1e CLKOUT frequency jitter (MF < 10)

—

0.50

2.00

3.00

0.50

—

0.50

2.00

3.00

0.50

—

0.50

2.00

3.00

0.50

—

0.50

2.00

3.00

0.50

—

1

B1f

CLKOUT frequency jitter (10 < MF < 500)

%

1

B1g CLKOUT frequency jitter (MF > 500)

—

%

2

B1h Frequency jitter on EXTCLK

—

%

B2

B3

B4

CLKOUT pulse width low

CLKOUT width high

12.12

—

10.00

—

8.00

—

6.06

—

ns

—

3

CLKOUT rise time

4.00

—

4.00

—

4.00

—

4.00

—

33

3

B5

B7

CLKOUT fall time

—

CLKOUT to A(0:31), BADDR(28:30),

7.58

6.25

5.00

3.80

RD/WR, BURST, D(0:31), DP(0:3) invalid

B7a CLKOUT to TSIZ(0:1), REG, RSV, AT(0:3),

BDIP, PTR invalid

7.58

—

6.25

—

5.00

—

3.80

—

ns

B7b CLKOUT to BR, BG, FRZ, VFLS(0:1),

4

VF(0:2) IWP(0:2), LWP(0:1), STS invalid

B8

CLKOUT to A(0:31), BADDR(28:30)

RD/WR, BURST, D(0:31), DP(0:3) valid

7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.04

B8a CLKOUT to TSIZ(0:1), REG, RSV, AT(0:3)

BDIP, PTR valid

B8b CLKOUT to BR, BG, VFLS(0:1), VF(0:2),

4

IWP(0:2), FRZ, LWP(0:1), STS valid

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

15

Bus Signal Timing

Table 7. Bus Operation Timings (continued)

33 MHz 40 MHz

Min Max Min Max

50 MHz

Min Max

66 MHz

Min Max

Num

Characteristic

Unit

B9

CLKOUT to A(0:31), BADDR(28:30),

RD/WR, BURST, D(0:31), DP(0:3),

TSIZ(0:1), REG, RSV, AT(0:3), PTR High-Z

7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.04

ns

B11 CLKOUT to TS, BB assertion

7.58 13.58 6.25 12.25 5.00 11.00 3.80 11.29

ns

B11a CLKOUT to TA, BI assertion (when driven by 2.50

the memory controller or PCMCIA interface)

9.25

2.50

9.25

2.50

9.25

2.50

9.75

B12 CLKOUT to TS, BB negation

7.58 14.33 6.25 13.00 5.00 11.75 3.80

8.54

9.00

ns

B12a CLKOUT to TA, BI negation (when driven by 2.50 11.00 2.50 11.00 2.50 11.00 2.50

the memory controller or PCMCIA interface)

B13 CLKOUT to TS, BB High-Z

7.58 21.58 6.25 20.25 5.00 19.00 3.80 14.04

2.50 15.00 2.50 15.00 2.50 15.00 2.50 15.00

ns

B13a CLKOUT to TA, BI High-Z (when driven by

the memory controller or PCMCIA interface)

B14 CLKOUT to TEA assertion

B15 CLKOUT to TEA High-Z

2.50 10.00 2.50 10.00 2.50 10.00 2.50

9.00

ns

2.50 15.00 2.50 15.00 2.50 15.00 2.50 15.00

B16 TA, BI valid to CLKOUT (setup time)

9.75

—

9.75

—

9.75

—

6.00

4.50

—

B16a TEA, KR, RETRY, CR valid to CLKOUT

(setup time)

10.00

5

B16b BB, BG, BR, valid to CLKOUT (setup time)

8.50

1.00

—

8.50

1.00

—

8.50

1.00

—

4.00

2.00

—

ns

B17 CLKOUT to TA, TEA, BI, BB, BG, BR valid

(hold time)

B17a CLKOUT to KR, RETRY, CR valid (hold

time)

2.00

6.00

1.00

4.00

2.00

—

2.00

6.00

1.00

4.00

2.00

—

2.00

6.00

1.00

4.00

2.00

—

2.00

6.00

2.00

4.00

2.00

—

ns

B18 D(0:31), DP(0:3) valid to CLKOUT rising

6

edge (setup time)

B19 CLKOUT rising edge to D(0:31), DP(0:3)

6

valid (hold time)

B20 D(0:31), DP(0:3) valid to CLKOUT falling

7

edge (setup time)

B21 CLKOUT falling edge to D(0:31), DP(0:3)

7

valid (hold time)

B22 CLKOUT rising edge to CS asserted GPCM 7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.04

ACS = 00

B22a CLKOUT falling edge to CS asserted GPCM

ACS = 10, TRLX = 0

—

8.00

—

8.00

—

8.00

—

8.00

B22b CLKOUT falling edge to CS asserted GPCM 7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.54

ACS = 11, TRLX = 0, EBDF = 0

B22c CLKOUT falling edge to CS asserted GPCM 10.86 17.99 8.88 16.00 7.00 14.13 5.18 12.31

ACS = 11, TRLX = 0, EBDF = 1

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

16

Freescale Semiconductor

Bus Signal Timing

Table 7. Bus Operation Timings (continued)

33 MHz 40 MHz

50 MHz

66 MHz

Unit

Num

Characteristic

Min

Max

Min

Max

Min

Max

Min

Max

B23 CLKOUT rising edge to CS negated GPCM 2.00

read access, GPCM write access ACS = 00,

TRLX = 0, and CSNT = 0

8.00

2.00

8.00

2.00

8.00

2.00

8.00

ns

B24 A(0:31) and BADDR(28:30) to CS asserted 5.58

GPCM ACS = 10, TRLX = 0

—

4.25

10.50

—

3.00

8.00

—

1.79

5.58

—

ns

B24a A(0:31) and BADDR(28:30) to CS asserted 13.15

GPCM ACS = 11, TRLX = 0

B25 CLKOUT rising edge to OE, WE(0:3)

asserted

—

9.00

B26 CLKOUT rising edge to OE negated

2.00

9.00

—

2.00

9.00

—

2.00

9.00

—

2.00

9.00

—

ns

B27 A(0:31) and BADDR(28:30) to CS asserted 35.88

GPCM ACS = 10, TRLX = 1

29.25

23.00

16.94

B27a A(0:31) and BADDR(28:30) to CS asserted 43.45

GPCM ACS = 11, TRLX = 1

—

35.50

—

28.00

—

20.73

—

ns

B28 CLKOUT rising edge to WE(0:3) negated

GPCM write access CSNT = 0

—

9.00

B28a CLKOUT falling edge to WE(0:3) negated

GPCM write access TRLX = 0, 1, CSNT = 1,

EBDF = 0

7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.54

B28b CLKOUT falling edge to CS negated GPCM

write access TRLX = 0, 1, CSNT = 1,

—

14.33

—

13.00

—

11.75

—

10.54

ns

ACS = 10, or ACS = 11, EBDF = 0

B28c CLKOUT falling edge to WE(0:3) negated

GPCM write access TRLX = 0, 1, CSNT = 1

write access TRLX = 0, CSNT = 1,

EBDF = 1

10.86 17.99 8.88 16.00 7.00 14.13 5.18 12.31

B28d CLKOUT falling edge to CS negated GPCM

write access TRLX = 0, 1, CSNT = 1,

—

17.99

—

16.00

—

14.13

—

12.31

ns

ACS = 10, or ACS = 11, EBDF = 1

B29 WE(0:3) negated to D(0:31), DP(0:3) High-Z 5.58

GPCM write access CSNT = 0, EBDF = 0

—

4.25

10.5

—

3.00

8.00

—

1.79

5.58

—

ns

B29a WE(0:3) negated to D(0:31), DP(0:3) High-Z 13.15

GPCM write access, TRLX = 0, CSNT = 1,

EBDF = 0

B29b CS negated to D(0:31), DP(0:3), High-Z

GPCM write access, ACS = 00, TRLX = 0, 1,

and CSNT = 0

5.58

—

4.25

10.5

—

3.00

8.00

—

1.79

5.58

—

ns

B29c CS negated to D(0:31), DP(0:3) High-Z

GPCM write access, TRLX = 0, CSNT = 1,

ACS = 10, or ACS = 11, EBDF = 0

13.15

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

17

Bus Signal Timing

Table 7. Bus Operation Timings (continued)

33 MHz 40 MHz

50 MHz

66 MHz

Num

Characteristic

Unit

Min

Max

Min

Max

Min

Max

Min

Max

B29d WE(0:3) negated to D(0:31), DP(0:3) High-Z 43.45

GPCM write access, TRLX = 1, CSNT = 1,

EBDF = 0

—

35.5

—

28.00

5.00

—

20.73

29.73

3.18

—

ns

B29e CS negated to D(0:31), DP(0:3) High-Z

GPCM write access, TRLX = 1, CSNT = 1,

ACS = 10, or ACS = 11, EBDF = 0

43.45

—

35.5

—

ns

B29f WE(0:3) negated to D(0:31), DP(0:3) High-Z 8.86

GPCM write access, TRLX = 0, CSNT = 1,

EBDF = 1

6.88

B29g CS negated to D(0:31), DP(0:3) High-Z

GPCM write access, TRLX = 0, CSNT = 1,

ACS = 10, or ACS = 11, EBDF = 1

8.86

6.88

5.00

3.18

B29h WE(0:3) negated to D(0:31), DP(0:3) High-Z 38.67

GPCM write access, TRLX = 1, CSNT = 1,

EBDF = 1

31.38

24.50

17.83

B29i CS negated to D(0:31), DP(0:3) High-Z

GPCM write access, TRLX = 1, CSNT = 1,

ACS = 10, or ACS = 11, EBDF = 1

38.67

B30 CS, WE(0:3) negated to A(0:31),

BADDR(28:30) invalid GPCM write access

5.58

—

4.25

—

3.00

8.00

—

1.79

5.58

—

ns

8

B30a WE(0:3) negated to A(0:31), BADDR(28:30) 13.15

invalid GPCM, write access, TRLX = 0,

10.50

CSNT = 1, CS negated to A(0:31) invalid

GPCM write access, TRLX = 0, CSNT = 1

ACS = 10, or ACS = 11, EBDF = 0

B30b WE(0:3) negated to A(0:31), invalid GPCM 43.45

BADDR(28:30) invalid GPCM write access,

TRLX = 1, CSNT = 1. CS negated to

A(0:31), Invalid GPCM, write access,

TRLX = 1, CSNT = 1, ACS = 10, or

—

35.50

—

28.00

—

20.73

—

ns

ACS = 11, EBDF = 0

B30c WE(0:3) negated to A(0:31), BADDR(28:30) 8.36

invalid GPCM write access, TRLX = 0,

—

6.38

31.38

1.50

—

4.50

24.50

1.50

—

2.68

17.83

1.50

—

ns

CSNT = 1. CS negated to A(0:31) invalid

GPCM write access, TRLX = 0, CSNT = 1,

ACS = 10, ACS = 11, EBDF = 1

B30d WE(0:3) negated to A(0:31), BADDR(28:30) 38.67

invalid GPCM write access, TRLX = 1,

CSNT =1. CS negated to A(0:31) invalid

GPCM write access TRLX = 1, CSNT = 1,

ACS = 10, or ACS = 11, EBDF = 1

B31 CLKOUT falling edge to CS valid—as

requested by control bit CST4 in the

corresponding word in UPM

1.50

6.00

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

18

Freescale Semiconductor

Bus Signal Timing

Table 7. Bus Operation Timings (continued)

33 MHz 40 MHz

Min Max Min Max

7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.54

50 MHz

Min Max

66 MHz

Unit

Num

Characteristic

Min

Max

B31a CLKOUT falling edge to CS valid—as

requested by control bit CST1 in the

corresponding word in UPM

ns

B31b CLKOUT rising edge to CS valid—as

requested by control bit CST2 in the

corresponding word in UPM

1.50

8.00

1.50

8.00

1.50

8.00

1.50

8.00

B31c CLKOUT rising edge to CS valid—as

requested by control bit CST3 in the

corresponding word in UPM

7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.04

13.26 17.99 11.28 16.00 9.40 14.13 7.58 12.31

B31d CLKOUT falling edge to CS valid—as

requested by control bit CST1 in the

corresponding word in UPM, EBDF = 1

B32 CLKOUT falling edge to BS valid—as

requested by control bit BST4 in the

corresponding word in UPM

1.50

6.00

1.50

6.00

1.50

6.00

1.50

6.00

B32a CLKOUT falling edge to BS valid—as

requested by control bit BST1 in the

7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.54

corresponding word in UPM, EBDF = 0

B32b CLKOUT rising edge to BS valid—as

requested by control bit BST2 in the

corresponding word in UPM

1.50

8.00

1.50

8.00

1.50

8.00

1.50

8.00

B32c CLKOUT rising edge to BS valid—as

requested by control bit BST3 in the

corresponding word in UPM

7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.54

13.26 17.99 11.28 16.00 9.40 14.13 7.58 12.31

B32d CLKOUT falling edge to BS valid—as

requested by control bit BST1 in the

corresponding word in UPM, EBDF = 1

B33 CLKOUT falling edge to GPL valid—as

requested by control bit GxT4 in the

corresponding word in UPM

1.50

6.00

1.50

6.00

1.50

6.00

1.50

6.00

B33a CLKOUT rising edge to GPL valid—as

requested by control bit GxT3 in the

corresponding word in UPM

7.58 14.33 6.25 13.00 5.00 11.75 3.80 10.54

B34 A(0:31), BADDR(28:30), and D(0:31) to CS 5.58

valid—as requested by control bit CST4 in

the corresponding word in UPM

—

4.25

10.50

16.75

—

3.00

8.00

—

1.79

5.58

9.36

—

B34a A(0:31), BADDR(28:30), and D(0:31) to CS 13.15

valid—as requested by control bit CST1 in

the corresponding word in UPM

B34b A(0:31), BADDR(28:30), and D(0:31) to CS 20.73

valid—as requested by control bit CST2 in

the corresponding word in UPM

13.00

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

19

Bus Signal Timing

Table 7. Bus Operation Timings (continued)

33 MHz 40 MHz

50 MHz

66 MHz

Num

Characteristic

Unit

Min

5.58

Max

Min

Max

Min

Max

Min

Max

B35 A(0:31), BADDR(28:30) to CS valid—as

requested by control bit BST4 in the

corresponding word in UPM

—

4.25

10.50

16.75

4.25

—

3.00

—

1.79

5.58

9.36

1.79

—

ns

B35a A(0:31), BADDR(28:30), and D(0:31) to BS 13.15

valid—as requested by control bit BST1 in

the corresponding word in UPM

—

8.00

—

ns

B35b A(0:31), BADDR(28:30), and D(0:31) to BS 20.73

valid—as requested by control bit BST2 in

the corresponding word in UPM

13.00

3.00

B36 A(0:31), BADDR(28:30), and D(0:31) to

GPL valid—as requested by control bit GxT4

in the corresponding word in UPM

5.58

9

B37 UPWAIT valid to CLKOUT falling edge

6.00

1.00

7.00

—

6.00

1.00

7.00

—

6.00

1.00

7.00

—

6.00

1.00

7.00

—

ns

9

B38 CLKOUT falling edge to UPWAIT valid

10

B39 AS valid to CLKOUT rising edge

B40 A(0:31), TSIZ(0:1), RD/WR, BURST, valid to 7.00

CLKOUT rising edge

B41 TS valid to CLKOUT rising edge (setup time) 7.00

B42 CLKOUT rising edge to TS valid (hold time) 2.00

—

7.00

2.00

—

7.00

2.00

—

7.00

2.00

—

ns

B43 AS negation to memory controller signals

negation

—

TBD

1

2

Phase and frequency jitter performance results are only valid if the input jitter is less than the prescribed value.

If the rate of change of the frequency of EXTAL is slow (that is, it does not jump between the minimum and maximum values

in one cycle) or the frequency of the jitter is fast (that is, it does not stay at an extreme value for a long time) then the maximum

allowed jitter on EXTAL can be up to 2%.

The timings specified in B4 and B5 are based on full strength clock.

The timing for BR output is relevant when the MPC860 is selected to work with external bus arbiter. The timing for BG output

is relevant when the MPC860 is selected to work with internal bus arbiter.

3

4

5

6

7

The timing required for BR input is relevant when the MPC860 is selected to work with internal bus arbiter. The timing for BG

input is relevant when the MPC860 is selected to work with external bus arbiter.

The D(0:31) and DP(0:3) input timings B18 and B19 refer to the rising edge of the CLKOUT in which the TA input signal is

asserted.

The D(0:31) and DP(0:3) input timings B20 and B21 refer to the falling edge of the CLKOUT. This timing is valid only for read

accesses controlled by chip-selects under control of the UPM in the memory controller, for data beats where DLT3 = 1 in the

UPM RAM words. (This is only the case where data is latched on the falling edge of CLKOUT.)

The timing B30 refers to CS when ACS = 00 and to WE(0:3) when CSNT = 0.

The signal UPWAIT is considered asynchronous to the CLKOUT and synchronized internally. The timings specified in B37 and

B38 are specified to enable the freeze of the UPM output signals as described in Figure 18.

The AS signal is considered asynchronous to the CLKOUT. The timing B39 is specified in order to allow the behavior specified

in Figure 21.

8

9

10

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

20

Freescale Semiconductor

Bus Signal Timing

Figure 3 is the control timing diagram.

CLKOUT

A

B

Outputs

Inputs

A

B

D

C

D

C

Inputs

A

B

C

D

Maximum output delay specification.

Minimum output hold time.

Minimum input setup time specification.

Minimum input hold time specification.

Figure 3. Control Timing

Figure 4 provides the timing for the external clock.

CLKOUT

B1

B3

B2

B4

B5

Figure 4. External Clock Timing

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

21

Bus Signal Timing

Figure 5 provides the timing for the synchronous output signals.

CLKOUT

B8

B7

B9

Output

Signals

B8a

B8b

B7a

B7b

B9

Output

Signals

Output

Signals

Figure 5. Synchronous Output Signals Timing

Figure 6 provides the timing for the synchronous active pull-up and open-drain output signals.

CLKOUT

B13

B11

B12

B12a

B15

TS, BB

B13a

B11a

B14

TA, BI

TEA

Figure 6. Synchronous Active Pull-Up Resistor and Open-Drain Outputs Signals Timing

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

22

Freescale Semiconductor

Bus Signal Timing

Figure 7 provides the timing for the synchronous input signals.

CLKOUT

B16

B17

TA, BI

B16a

B17a

B17

TEA, KR,

RETRY, CR

B16b

BB, BG, BR

Figure 7. Synchronous Input Signals Timing

Figure 8 provides normal case timing for input data. It also applies to normal read accesses under the

control of the UPM in the memory controller.

CLKOUT

B16

B17

TA

B18

B19

D[0:31],

DP[0:3]

Figure 8. Input Data Timing in Normal Case

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

23

Bus Signal Timing

Figure 9 provides the timing for the input data controlled by the UPM for data beats where DLT3 = 1 in

the UPM RAM words. (This is only the case where data is latched on the falling edge of CLKOUT.)

CLKOUT

TA

B20

B21

D[0:31],

DP[0:3]

Figure 9. Input Data Timing when Controlled by UPM in the Memory Controller and DLT3 = 1

Figure 10 through Figure 13 provide the timing for the external bus read controlled by various GPCM

factors.

CLKOUT

B11

B8

B12

TS

A[0:31]

CSx

B22

B23

B25

B26

B19

OE

B28

WE[0:3]

B18

D[0:31],

DP[0:3]

Figure 10. External Bus Read Timing (GPCM Controlled—ACS = 00)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

24

Freescale Semiconductor

Bus Signal Timing

CLKOUT

TS

B11

B8

B12

A[0:31]

CSx

B22a

B24

B23

B25

B26

B19

OE

B18

D[0:31],

DP[0:3]

Figure 11. External Bus Read Timing (GPCM Controlled—TRLX = 0, ACS = 10)

CLKOUT

TS

B11

B8

B12

B22b

B22c

A[0:31]

B23

CSx

OE

B24a

B25

B26

B19

B18

D[0:31],

DP[0:3]

Figure 12. External Bus Read Timing (GPCM Controlled—TRLX = 0, ACS = 11)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

25

Bus Signal Timing

CLKOUT

B11

B12

TS

B8

A[0:31]

B22a

B23

CSx

OE

B27

B26

B19

B27a

B22bB22c

B18

D[0:31],

DP[0:3]

Figure 13. External Bus Read Timing (GPCM Controlled—TRLX = 0 or 1, ACS = 10, ACS = 11)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

26

Freescale Semiconductor

Bus Signal Timing

Figure 14 through Figure 16 provide the timing for the external bus write controlled by various GPCM

factors.

CLKOUT

B11

B8

B12

TS

B30

A[j0:31]

B22

B23

CSx

WE[0:3]

OE

B25

B28

B29b

B29

B26

B8

B9

D[0:31],

DP[0:3]

Figure 14. External Bus Write Timing (GPCM Controlled—TRLX = 0 or 1, CSNT = 0)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

27

Bus Signal Timing

CLKOUT

B11

B8

B12

TS

B30aB30c

B23

A[0:31]

B28b B28d

B25

B22

CSx

WE[0:3]

OE

B29c B29g

B29a B29f

B26

B28a B28c

B8

B9

D[0:31],

DP[0:3]

Figure 15. External Bus Write Timing (GPCM Controlled—TRLX = 0 or 1, CSNT = 1)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

28

Freescale Semiconductor

Bus Signal Timing

CLKOUT

TS

B11

B12

B30b B30d

B8

A[0:31]

B28b B28d

B22

B23

CSx

WE[0:3]

OE

B29e B29i

B29d B29h

B25

B26

B29b

B28a B28c

B8

B9

D[0:31],

DP[0:3]

Figure 16. External Bus Write Timing (GPCM Controlled—TRLX = 0 or 1, CSNT = 1)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

29

Bus Signal Timing

Figure 17 provides the timing for the external bus controlled by the UPM.

CLKOUT

B8

A[0:31]

B31a

B31d

B31c

B31b

B31

CSx

B34

B34a

B34b

B32aB32d

B32c

B32b

B32

BS_A[0:3],

BS_B[0:3]

B35 B36

B35b

B35a

B33a

B33

GPL_A[0:5],

GPL_B[0:5]

Figure 17. External Bus Timing (UPM Controlled Signals)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

30

Freescale Semiconductor

Bus Signal Timing

Figure 18 provides the timing for the asynchronous asserted UPWAIT signal controlled by the UPM.

CLKOUT

UPWAIT

CSx

B37

B38

BS_A[0:3],

BS_B[0:3]

GPL_A[0:5],

GPL_B[0:5]

Figure 18. Asynchronous UPWAIT Asserted Detection in UPM Handled Cycles Timing

Figure 19 provides the timing for the asynchronous negated UPWAIT signal controlled by the UPM.

CLKOUT

B37

UPWAIT

B38

CSx

BS_A[0:3],

BS_B[0:3]

GPL_A[0:5],

GPL_B[0:5]

Figure 19. Asynchronous UPWAIT Negated Detection in UPM Handled Cycles Timing

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

31

Bus Signal Timing

Figure 20 provides the timing for the synchronous external master access controlled by the GPCM.

CLKOUT

B41

B40

B42

TS

A[0:31],

TSIZ[0:1],

R/W, BURST

B22

CSx

Figure 20. Synchronous External Master Access Timing (GPCM Handled ACS = 00)

Figure 21 provides the timing for the asynchronous external master memory access controlled by the

GPCM.

CLKOUT

B39

AS

B40

A[0:31],

TSIZ[0:1],

R/W

B22

CSx

Figure 21. Asynchronous External Master Memory Access Timing (GPCM Controlled—ACS = 00)

Figure 22 provides the timing for the asynchronous external master control signals negation.

AS

B43

CSx, WE[0:3],

OE, GPLx,

BS[0:3]

Figure 22. Asynchronous External Master—Control Signals Negation Timing

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

32

Freescale Semiconductor

Bus Signal Timing

Table 8 provides interrupt timing for the MPC860.

Table 8. Interrupt Timing

All Frequencies

Min Max

1

Num

Characteristic

Unit

I39

I40

I41

I42

I43

IRQx valid to CLKOUT rising edge (setup time)

IRQx hold time after CLKOUT

IRQx pulse width low

6.00

2.00

3.00

—

ns

—

IRQx pulse width high

IRQx edge-to-edge time

4 × T

CLOCKOUT

1

The timings I39 and I40 describe the testing conditions under which the IRQ lines are tested when being defined as

level-sensitive. The IRQ lines are synchronized internally and do not have to be asserted or negated with reference to the

CLKOUT.

The timings I41, I42, and I43 are specified to allow the correct function of the IRQ lines detection circuitry and have no direct

relation with the total system interrupt latency that the MPC860 is able to support.

Figure 23 provides the interrupt detection timing for the external level-sensitive lines.

CLKOUT

I39

I40

IRQx

Figure 23. Interrupt Detection Timing for External Level Sensitive Lines

Figure 24 provides the interrupt detection timing for the external edge-sensitive lines.

CLKOUT

I41

I42

IRQx

I43

Figure 24. Interrupt Detection Timing for External Edge Sensitive Lines

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

33

Bus Signal Timing

Table 9 shows the PCMCIA timing for the MPC860.

Table 9. PCMCIA Timing

33 MHz 40 MHz

50 MHz

66 MHz

Num

Characteristic

Unit

Min

Max

Min

Max

Min

Max

Min

Max

P44 A(0:31), REG valid to PCMCIA Strobe

20.73

—

16.75

—

13.00

—

9.36

—

ns

1

asserted

1

P45 A(0:31), REG valid to ALE negation

28.30

—

23.00

—

18.00

—

13.15

—

ns

P46 CLKOUT to REG valid

7.58 15.58 6.25 14.25 5.00 13.00 3.79 11.84

8.58 7.25 6.00 4.84

P47 CLKOUT to REG invalid

—

P48 CLKOUT to CE1, CE2 asserted

P49 CLKOUT to CE1, CE2 negated

7.58 15.58 6.25 14.25 5.00 13.00 3.79 11.84

P50 CLKOUT to PCOE, IORD, PCWE, IOWR

assert time

—

11.00

—

11.00

—

11.00

P51 CLKOUT to PCOE, IORD, PCWE, IOWR

negate time

2.00 11.00 2.00 11.00 2.00 11.00 2.00 11.00

ns

P52 CLKOUT to ALE assert time

P53 CLKOUT to ALE negate time

7.58 15.58 6.25 14.25 5.00 13.00 3.79 10.04

ns

—

15.58

—

14.25

—

13.00

—

11.84

—

1

P54 PCWE, IOWR negated to D(0:31) invalid

5.58

8.00

4.25

8.00

3.00

8.00

1.79

8.00

P55 WAITA and WAITB valid to CLKOUT rising

—

1

edge

P56 CLKOUT rising edge to WAITA and WAITB

2.00

—

2.00

—

2.00

—

2.00

—

ns

1

invalid

1

PSST = 1. Otherwise add PSST times cycle time.

PSHT = 0. Otherwise add PSHT times cycle time.

These synchronous timings define when the WAITx signals are detected in order to freeze (or relieve) the

PCMCIA current cycle. The WAITx assertion will be effective only if it is detected 2 cycles before the

PSL timer expiration. See Chapter 16, “PCMCIA Interface,” in the MPC860 PowerQUICC™ Family

User’s Manual.

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

34

Freescale Semiconductor

Bus Signal Timing

Figure 25 provides the PCMCIA access cycle timing for the external bus read.

CLKOUT

TS

P44

A[0:31]

P46

P48

P45

P47

P49

P51

P52

REG

CE1/CE2

PCOE, IORD

ALE

P50

P53

P52

B18

B19

D[0:31]

Figure 25. PCMCIA Access Cycle Timing External Bus Read

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

35

Bus Signal Timing

Figure 26 provides the PCMCIA access cycle timing for the external bus write.

CLKOUT

TS

P44

A[0:31]

P46

P48

P45

P47

P49

P51

P52

B9

REG

CE1/CE2

PCWE, IOWR

ALE

P50

P53

B8

P54

P52

D[0:31]

Figure 26. PCMCIA Access Cycle Timing External Bus Write

Figure 27 provides the PCMCIA WAIT signal detection timing.

CLKOUT

P55

P56

WAITx

Figure 27. PCMCIA WAIT Signal Detection Timing

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

36

Freescale Semiconductor

Bus Signal Timing

Table 10 shows the PCMCIA port timing for the MPC860.

Table 10. PCMCIA Port Timing

33 MHz 40 MHz

50 MHz

66 MHz

Unit

Num

Characteristic

Min

Max

Min

Max

Min

Max

Min

Max

P57 CLKOUT to OPx valid

—

19.00

—

19.00

—

19.00

—

19.00

—

ns

1

P58 HRESET negated to OPx drive

25.73

5.00

1.00

21.75

5.00

1.00

18.00

5.00

1.00

14.36

5.00

1.00

P59 IP_Xx valid to CLKOUT rising edge

P60 CLKOUT rising edge to IP_Xx invalid

OP2 and OP3 only.

—

1

Figure 28 provides the PCMCIA output port timing for the MPC860.

CLKOUT

P57

Output

Signals

HRESET

P58

OP2, OP3

Figure 28. PCMCIA Output Port Timing

Figure 29 provides the PCMCIA output port timing for the MPC860.

CLKOUT

P59

P60

Input

Signals

Figure 29. PCMCIA Input Port Timing

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

37

Bus Signal Timing

Table 11 shows the debug port timing for the MPC860.

Table 11. Debug Port Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

P61 DSCK cycle time

3 × T

—

ns

CLOCKOUT

P62 DSCK clock pulse width

P63 DSCK rise and fall times

1.25 × T

CLOCKOUT

0.00

3.00

—

P64 DSDI input data setup time

P65 DSDI data hold time

8.00

5.00

0.00

—

P66 DSCK low to DSDO data valid

P67 DSCK low to DSDO invalid

15.00

2.00

Figure 30 provides the input timing for the debug port clock.

DSCK

D61

D62

D61

D62

D63

Figure 30. Debug Port Clock Input Timing

D63

Figure 31 provides the timing for the debug port.

DSCK

D64

D65

DSDI

D66

D67

DSDO

Figure 31. Debug Port Timings

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

38

Freescale Semiconductor

Bus Signal Timing

Table 12 shows the reset timing for the MPC860.

Table 12. Reset Timing

33 MHz 40 MHz

50 MHz

66 MHz

Num

Characteristic

Unit

Min

Max

Min

Max

Min

Max

Min

Max

R69 CLKOUT to HRESET high impedance

R70 CLKOUT to SRESET high impedance

R71 RSTCONF pulse width

—

20.00

—

20.00

—

20.00

—

20.00

—

ns

515.15

—

425.00

—

340.00

—

257.58

—

R72

—

R73 Configuration data to HRESET rising edge 504.55

setup time

—

425.00

350.00

—

277.27

—

ns

R74 Configuration data to RSTCONF rising

edge setup time

350.00

0.00

—

350.00

0.00

—

350.00

0.00

—

350.00

0.00

—

R75 Configuration data hold time after

RSTCONF negation

R76 Configuration data hold time after

HRESET negation

—

0.00

—

R77 HRESET and RSTCONF asserted to data

out drive

25.00

R78 RSTCONF negated to data out high

impedance

—

R79 CLKOUT of last rising edge before chip

three-state HRESET to data out high

impedance

—

R80 DSDI, DSCK setup

90.91

0.00

—

75.00

0.00

—

60.00

0.00

—

45.45

0.00

—

ns

R81 DSDI, DSCK hold time

R82 SRESET negated to CLKOUT rising edge 242.42

for DSDI and DSCK sample

200.00

160.00

121.21

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

39

Bus Signal Timing

Figure 32 shows the reset timing for the data bus configuration.

HRESET

R71

R76

RSTCONF

D[0:31] (IN)

R73

R74

R75

Figure 32. Reset Timing—Configuration from Data Bus

Figure 33 provides the reset timing for the data bus weak drive during configuration.

CLKOUT

R69

HRESET

R79

RSTCONF

R77

R78

D[0:31] (OUT)

(Weak)

Figure 33. Reset Timing—Data Bus Weak Drive During Configuration

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

40

Freescale Semiconductor

IEEE 1149.1 Electrical Specifications

Figure 34 provides the reset timing for the debug port configuration.

CLKOUT

R70

R82

SRESET

R80

R81

DSCK, DSDI

Figure 34. Reset Timing—Debug Port Configuration

10 IEEE 1149.1 Electrical Specifications

Table 13 provides the JTAG timings for the MPC860 shown in Figure 35 through Figure 38.

Table 13. JTAG Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

J82

J83

J84

J85

J86

J87

J88

J89

J90

J91

J92

J93

J94

J95

J96

TCK cycle time

100.00

40.00

0.00

5.00

25.00

—

ns

TCK clock pulse width measured at 1.5 V

TCK rise and fall times

10.00

—

TMS, TDI data setup time

TMS, TDI data hold time

—

TCK low to TDO data valid

27.00

—

TCK low to TDO data invalid

0.00

—

TCK low to TDO high impedance

TRST assert time

20.00

—

100.00

40.00

—

TRST setup time to TCK low

—

TCK falling edge to output valid

TCK falling edge to output valid out of high impedance

TCK falling edge to output high impedance

Boundary scan input valid to TCK rising edge

TCK rising edge to boundary scan input invalid

50.00

—

50.00

—

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

41

IEEE 1149.1 Electrical Specifications

TCK

J82

J83

J82

J83

J84

Figure 35. JTAG Test Clock Input Timing

TCK

J85

J86

TMS, TDI

J87

J88

J89

TDO

TCK

Figure 36. JTAG Test Access Port Timing Diagram

J91

J90

TRST

TCK

Figure 37. JTAG TRST Timing Diagram

J92

J93

J94

Output

Signals

Output

Signals

J95

J96

Output

Signals

Figure 38. Boundary Scan (JTAG) Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

42

Freescale Semiconductor

CPM Electrical Characteristics

11 CPM Electrical Characteristics

This section provides the AC and DC electrical specifications for the communications processor module

(CPM) of the MPC860.

11.1 PIP/PIO AC Electrical Specifications

Table 14 provides the PIP/PIO AC timings as shown in Figure 39 through Figure 43.

Table 14. PIP/PIO Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

21

22

23

24

25

26

27

28

29

30

31

Data-in setup time to STBI low

Data-in hold time to STBI high

STBI pulse width

0

2.5 – t3

1.5

—

2

ns

CLK

ns

1

STBO pulse width

1 CLK – 5 ns

Data-out setup time to STBO low

2

5

CLK

ns

Data-out hold time from STBO high

STBI low to STBO low (Rx interlock)

STBI low to STBO high (Tx interlock)

Data-in setup time to clock high

—

2

—

25

15

7.5

—

Data-in hold time from clock high

ns

Clock low to data-out valid (CPU writes data, control, or direction)

ns

1

t3 = Specification 23.

DATA-IN

21

22

23

STBI

27

24

STBO

Figure 39. PIP Rx (Interlock Mode) Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

43

CPM Electrical Characteristics

DATA-OUT

25

26

24

STBO

(Output)

28

23

STBI

(Input)

Figure 40. PIP Tx (Interlock Mode) Timing Diagram

DATA-IN

21

22

23

24

STBI

(Input)

STBO

(Output)

Figure 41. PIP Rx (Pulse Mode) Timing Diagram

DATA-OUT

25

26

24

STBO

(Output)

23

STBI

(Input)

Figure 42. PIP TX (Pulse Mode) Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

44

Freescale Semiconductor

CPM Electrical Characteristics

CLKO

DATA-IN

29

30

31

DATA-OUT

Figure 43. Parallel I/O Data-In/Data-Out Timing Diagram

11.2 Port C Interrupt AC Electrical Specifications

Table 15 provides the timings for port C interrupts.

Table 15. Port C Interrupt Timing

1

≥ 33.34 MHz

Num

Characteristic

Unit

Min

Max

35

36

Port C interrupt pulse width low (edge-triggered mode)

Port C interrupt minimum time between active edges

55

—

ns

1

External bus frequency of greater than or equal to 33.34 MHz.

Figure 44 shows the port C interrupt detection timing.

36

Port C

(Input)

35

Figure 44. Port C Interrupt Detection Timing

11.3 IDMA Controller AC Electrical Specifications

Table 16 provides the IDMA controller timings as shown in Figure 45 through Figure 48.

Table 16. IDMA Controller Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

40

41

DREQ setup time to clock high

DREQ hold time from clock high

7

3

—

ns

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

45

CPM Electrical Characteristics

Table 16. IDMA Controller Timing (continued)

Characteristic

All Frequencies

Num

Unit

Min

Max

42

43

44

45

46

SDACK assertion delay from clock high

SDACK negation delay from clock low

—

7

12

20

15

—

ns

SDACK negation delay from TA low

SDACK negation delay from clock high

TA assertion to rising edge of the clock setup time (applies to external TA)

CLKO

(Output)

41

40

DREQ

(Input)

Figure 45. IDMA External Requests Timing Diagram

CLKO

(Output)

TS

(Output)

R/W

(Output)

42

43

DATA

46

TA

(Input)

SDACK

Figure 46. SDACK Timing Diagram—Peripheral Write, Externally-Generated TA

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

46

Freescale Semiconductor

CPM Electrical Characteristics

CLKO

(Output)

TS

(Output)

R/W

(Output)

42

44

DATA

TA

(Output)

SDACK

Figure 47. SDACK Timing Diagram—Peripheral Write, Internally-Generated TA

CLKO

(Output)

TS

(Output)

R/W

(Output)

42

45

DATA

TA

(Output)

SDACK

Figure 48. SDACK Timing Diagram—Peripheral Read, Internally-Generated TA

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

47

CPM Electrical Characteristics

11.4 Baud Rate Generator AC Electrical Specifications

Table 17 provides the baud rate generator timings as shown in Figure 49.

Table 17. Baud Rate Generator Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

50

51

52

BRGO rise and fall time

BRGO duty cycle

BRGO cycle

—

40

10

60

—

ns

%

ns

50

BRGOX

51

52

Figure 49. Baud Rate Generator Timing Diagram

11.5 Timer AC Electrical Specifications

Table 18 provides the general-purpose timer timings as shown in Figure 50.

Table 18. Timer Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

61

62

63

64

65

TIN/TGATE rise and fall time

TIN/TGATE low time

10

1

—

25

ns

CLK

ns

TIN/TGATE high time

TIN/TGATE cycle time

CLKO low to TOUT valid

2

3

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

48

Freescale Semiconductor

CPM Electrical Characteristics

CLKO

60

61

63

62

TIN/TGATE

(Input)

61

64

65

TOUT

(Output)

Figure 50. CPM General-Purpose Timers Timing Diagram

11.6 Serial Interface AC Electrical Specifications

Table 19 provides the serial interface timings as shown in Figure 51 through Figure 55.

Table 19. SI Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

1, 2

70

71

71a

72

73

74

75

76

77

78

L1RCLK, L1TCLK frequency (DSC = 0)

—

SYNCCLK/2.5 MHz

2

L1RCLK, L1TCLK width low (DSC = 0)

P + 10

—

ns

MHz

3

L1RCLK, L1TCLK width high (DSC = 0)

L1TXD, L1ST(1–4), L1RQ, L1CLKO rise/fall time

L1RSYNC, L1TSYNC valid to L1CLK edge (SYNC setup time)

L1CLK edge to L1RSYNC, L1TSYNC, invalid (SYNC hold time)

L1RSYNC, L1TSYNC rise/fall time

15.00

—

20.00

35.00

—

15.00

—

L1RXD valid to L1CLK edge (L1RXD setup time)

L1CLK edge to L1RXD invalid (L1RXD hold time)

17.00

13.00

10.00

0.00

—

4

L1CLK edge to L1ST(1–4) valid

45.00

55.00

42.00

78A L1SYNC valid to L1ST(1–4) valid

79

80

L1CLK edge to L1ST(1–4) invalid

L1CLK edge to L1TXD valid

4

80A L1TSYNC valid to L1TXD valid

81

82

L1CLK edge to L1TXD high impedance

L1RCLK, L1TCLK frequency (DSC =1 )

—

16.00 or

SYNCCLK/2

83

L1RCLK, L1TCLK width low (DSC = 1)

L1RCLK, L1TCLK width high (DSC = 1)

P + 10

—

ns

3

83a

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

49

CPM Electrical Characteristics

Table 19. SI Timing (continued)

All Frequencies

Num

Characteristic

Unit

Min

Max

84

85

L1CLK edge to L1CLKO valid (DSC = 1)

—

30.00

—

ns

4

L1RQ valid before falling edge of L1TSYNC

1.00

L1TCL

K

2

86

87

88

L1GR setup time

42.00

—

ns

L1GR hold time

L1CLK edge to L1SYNC valid (FSD = 00) CNT = 0000, BYT = 0, DSC = 0)

0.00

1

2

3

4

The ratio SYNCCLK/L1RCLK must be greater than 2.5/1.

These specs are valid for IDL mode only.

Where P = 1/CLKOUT. Thus, for a 25-MHz CLKO1 rate, P = 40 ns.

These strobes and TxD on the first bit of the frame become valid after L1CLK edge or L1SYNC, whichever comes later.

L1RCLK

(FE = 0, CE = 0)

(Input)

71

70

71a

72

L1RCLK

(FE = 1, CE = 1)

(Input)

RFSD=1

75

74

L1RSYNC

(Input)

73

77

L1RXD

(Input)

BIT0

76

78

79

L1ST(4–1)

(Output)

Figure 51. SI Receive Timing Diagram with Normal Clocking (DSC = 0)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

50

Freescale Semiconductor

CPM Electrical Characteristics

L1RCLK

(FE = 1, CE = 1)

(Input)

72

83a

82

L1RCLK

(FE = 0, CE = 0)

(Input)

RFSD=1

75

L1RSYNC

(Input)

73

74

77

L1RXD

(Input)

BIT0

76

78

79

L1ST(4–1)

(Output)

84

L1CLKO

(Output)

Figure 52. SI Receive Timing with Double-Speed Clocking (DSC = 1)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

51

CPM Electrical Characteristics

L1TCLK

(FE = 0, CE = 0)

(Input)

71

70

72

L1TCLK

(FE = 1, CE = 1)

(Input)

73

TFSD=0

75

74

L1TSYNC

(Input)

80a

BIT0

80

81

L1TXD

(Output)

79

78

L1ST(4–1)

(Output)

Figure 53. SI Transmit Timing Diagram (DSC = 0)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

52

Freescale Semiconductor

CPM Electrical Characteristics

L1RCLK

(FE = 0, CE = 0)

(Input)

72

83a

82

L1RCLK

(FE = 1, CE = 1)

(Input)

TFSD=0

75

L1RSYNC

(Input)

73

74

81

L1TXD

(Output)

BIT0

80

78a

79

L1ST(4–1)

(Output)

78

84

L1CLKO

(Output)

Figure 54. SI Transmit Timing with Double Speed Clocking (DSC = 1)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

53

CPM Electrical Characteristics

Figure 55. IDL Timing

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

54

Freescale Semiconductor

CPM Electrical Characteristics

11.7 SCC in NMSI Mode Electrical Specifications

Table 20 provides the NMSI external clock timing.

Table 20. NMSI External Clock Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

1

100

101

102

103

104

105

106

107

108

RCLK1 and TCLK1 width high

1/SYNCCLK

—

ns

RCLK1 and TCLK1 width low

1/SYNCCLK + 5

RCLK1 and TCLK1 rise/fall time

—

15.00

50.00

—

TXD1 active delay (from TCLK1 falling edge)

RTS1 active/inactive delay (from TCLK1 falling edge)

CTS1 setup time to TCLK1 rising edge

RXD1 setup time to RCLK1 rising edge

0.00

5.00

—

2

RXD1 hold time from RCLK1 rising edge

—

CD1 setup Time to RCLK1 rising edge

—

1

2

The ratios SYNCCLK/RCLK1 and SYNCCLK/TCLK1 must be greater than or equal to 2.25/1.

Also applies to CD and CTS hold time when they are used as external sync signals.

Table 21 provides the NMSI internal clock timing.

Table 21. NMSI Internal Clock Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

1

100

102

103

104

105

106

107

108

RCLK1 and TCLK1 frequency

0.00

—

SYNCCLK/3

MHz

ns

RCLK1 and TCLK1 rise/fall time

—

30.00

—

TXD1 active delay (from TCLK1 falling edge)

RTS1 active/inactive delay (from TCLK1 falling edge)

CTS1 setup time to TCLK1 rising edge

RXD1 setup time to RCLK1 rising edge

0.00

40.00

0.00

40.00

ns

—

ns

2

RXD1 hold time from RCLK1 rising edge

—

ns

CD1 setup time to RCLK1 rising edge

—

ns

1

2

The ratios SYNCCLK/RCLK1 and SYNCCLK/TCLK1 must be greater than or equal to 3/1.

Also applies to CD and CTS hold time when they are used as external sync signals.

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

55

CPM Electrical Characteristics

Figure 56 through Figure 58 show the NMSI timings.

RCLK1

102

101

106

100

RxD1

(Input)

107

108

CD1

(Input)

107

CD1

(SYNC Input)

Figure 56. SCC NMSI Receive Timing Diagram

TCLK1

102

101

100

TxD1

(Output)

103

105

RTS1

(Output)

104

CTS1

(Input)

107

CTS1

(SYNC Input)

Figure 57. SCC NMSI Transmit Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

56

Freescale Semiconductor

CPM Electrical Characteristics

TCLK1

102

101

100

TxD1

(Output)

103

RTS1

(Output)

104

107

104

105

CTS1

(Echo Input)

Figure 58. HDLC Bus Timing Diagram

11.8 Ethernet Electrical Specifications

Table 22 provides the Ethernet timings as shown in Figure 59 through Figure 63.

Table 22. Ethernet Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

CLSN width high

RCLK1 rise/fall time

RCLK1 width low

RCLK1 clock period

RXD1 setup time

RXD1 hold time

40

—

15

—

ns

40

80

20

5

1

120

—

RENA active delay (from RCLK1 rising edge of the last data bit)

10

100

—

RENA width low

TCLK1 rise/fall time

TCLK1 width low

—

15

—

40

99

10

1

TCLK1 clock period

101

50

TXD1 active delay (from TCLK1 rising edge)

TXD1 inactive delay (from TCLK1 rising edge)

TENA active delay (from TCLK1 rising edge)

TENA inactive delay (from TCLK1 rising edge)

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

57

CPM Electrical Characteristics

Table 22. Ethernet Timing (continued)

Characteristic

All Frequencies

Num

Unit

Min

Max

135

136

137

138

139

RSTRT active delay (from TCLK1 falling edge)

RSTRT inactive delay (from TCLK1 falling edge)

10

1

50

—

20

ns

REJECT width low

CLK

ns

2

CLKO1 low to SDACK asserted

—

2

CLKO1 low to SDACK negated

ns

1

2

The ratios SYNCCLK/RCLK1 and SYNCCLK/TCLK1 must be greater than or equal to 2/1.

SDACK is asserted whenever the SDMA writes the incoming frame DA into memory.

CLSN(CTS1)

(Input)

120

Figure 59. Ethernet Collision Timing Diagram

RCLK1

121

124

123

RxD1

(Input)

Last Bit

125

126

127

RENA(CD1)

(Input)

Figure 60. Ethernet Receive Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

58

Freescale Semiconductor

CPM Electrical Characteristics

TCLK1

128

129

131

121

TxD1

(Output)

132

133

134

TENA(RTS1)

(Input)

RENA(CD1)

(Input)

(Note 2)

Notes:

1. Transmit clock invert (TCI) bit in GSMR is set.

2. If RENA is deasserted before TENA, or RENA is not asserted at all during transmit, then the CSL bit is set in

the buffer descriptor at the end of the frame transmission.

Figure 61. Ethernet Transmit Timing Diagram

RCLK1

RxD1

(Input)

0

1

BIT1

125

BIT2

136

Start Frame Delimiter

RSTRT

(Output)

Figure 62. CAM Interface Receive Start Timing Diagram

REJECT

137

Figure 63. CAM Interface REJECT Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

59

CPM Electrical Characteristics

11.9 SMC Transparent AC Electrical Specifications

Table 23 provides the SMC transparent timings as shown in Figure 64.

Table 23. SMC Transparent Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

1

150

151

SMCLK clock period

SMCLK width low

100

50

—

15

50

—

ns

151A SMCLK width high

152

153

154

155

SMCLK rise/fall time

SMTXD active delay (from SMCLK falling edge)

SMRXD/SMSYNC setup time

10

20

5

RXD1/SMSYNC hold time

1

SYNCCLK must be at least twice as fast as SMCLK.

SMCLK

151A

150

152

151

SMTXD

(Output)

Note 1

154

153

155

SMSYNC

154

155

SMRXD

(Input)

Note:

1. This delay is equal to an integer number of character-length clocks.

Figure 64. SMC Transparent Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

60

Freescale Semiconductor

CPM Electrical Characteristics

11.10 SPI Master AC Electrical Specifications

Table 24 provides the SPI master timings as shown in Figure 65 and Figure 66.

Table 24. SPI Master Timing

All Frequencies

Unit

Num

Characteristic

Min

Max

160

161

162

163

164

165

166

167

MASTER cycle time

4

2

1024

512

—

t

cyc

MASTER clock (SCK) high or low time

MASTER data setup time (inputs)

Master data hold time (inputs)

Master data valid (after SCK edge)

Master data hold time (outputs)

Rise time output

50

0

ns

—

0

20

—

15

Fall time output

15

SPICLK

(CI = 0)

(Output)

161

167

166

167

160

SPICLK

(CI = 1)

(Output)

163

162

SPIMISO

msb

167

Data

165

lsb

msb

(Input)

164

166

SPIMOSI

(Output)

msb

Data

lsb

msb

Figure 65. SPI Master (CP = 0) Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

61

CPM Electrical Characteristics

SPICLK

(CI = 0)

(Output)

161

167

166

167

161

160

SPICLK

(CI = 1)

(Output)

163

162

SPIMISO

(Input)

msb

167

Data

165

lsb

msb

164

166

SPIMOSI

(Output)

msb

Data

lsb

msb

Figure 66. SPI Master (CP = 1) Timing Diagram

11.11 SPI Slave AC Electrical Specifications

Table 25 provides the SPI slave timings as shown in Figure 67 and Figure 68.

Table 25. SPI Slave Timing

All Frequencies

Num

Characteristic

Unit

Min

Max

170

171

172

173

174

175

176

177

Slave cycle time

2

15

1

—

50

t

cyc

Slave enable lead time

Slave enable lag time

ns

Slave clock (SPICLK) high or low time

Slave sequential transfer delay (does not require deselect)

Slave data setup time (inputs)

t

cyc

1

t

20

—

ns

Slave data hold time (inputs)

Slave access time

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

62

Freescale Semiconductor

CPM Electrical Characteristics

SPISEL

(Input)

172

171

174

SPICLK

(CI = 0)

(Input)

173

182

181

173

170

SPICLK

(CI = 1)

(Input)

177

181

182

180

178

Undef

SPIMISO

(Output)

msb

175

Data

lsb

msb

179

176

181 182

lsb

SPIMOSI

(Input)

msb

Data

Figure 67. SPI Slave (CP = 0) Timing Diagram

SPISEL

(Input)

172

174

171

170

SPICLK

(CI = 0)

(Input)

173

182

181

182

173

181

SPICLK

(CI = 1)

(Input)

177

180

178

SPIMISO

(Output)

msb

Undef

175

Data

lsb

179

176

msb

181 182

Data

SPIMOSI

(Input)

lsb

Figure 68. SPI Slave (CP = 1) Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

63

CPM Electrical Characteristics

2

11.12 I C AC Electrical Specifications

2

Table 26 provides the I C (SCL < 100 kHz) timings.

2

Table 26. I C Timing (SCL < 100 kHZ)

All Frequencies

Num

Characteristic

Unit

Min

Max

200

202

203

204

205

206

207

208

209

210

211

SCL clock frequency (slave)

SCL clock frequency (master)

0

100

—

kHz

μs

1

1.5

4.7

4.0

4.7

4.0

0

Bus free time between transmissions

Low period of SCL

—

μs

High period of SCL

—

μs

Start condition setup time

Start condition hold time

Data hold time

—

μs

—

μs

—

μs

Data setup time

250

—

ns

SDL/SCL rise time

1

μs

SDL/SCL fall time

—

300

—

ns

Stop condition setup time

4.7

μs

1

SCL frequency is given by SCL = BRGCLK_frequency / ((BRG register + 3 × pre_scaler × 2).

The ratio SYNCCLK/(BRGCLK/pre_scaler) must be greater than or equal to 4/1.

2

Table 27 provides the I C (SCL > 100 kHz) timings.

2

Table 27. . I C Timing (SCL > 100 kHZ)

All Frequencies

Num

Characteristic

SCL clock frequency (slave)

Expression

Unit

Min

Max

200

202

203

204

205

206

207

208

209

210

211

fSCL

0

BRGCLK/48

Hz

s

1

SCL clock frequency (master)

BRGCLK/16512

1/(2.2 * fSCL)

0

BRGCLK/48

Bus free time between transmissions

Low period of SCL

—

s

High period of SCL

—

s

Start condition setup time

Start condition hold time

Data hold time

—

s

—

s

—

s

Data setup time

1/(40 * fSCL)

—

s

SDL/SCL rise time

1/(10 * fSCL)

1/(33 * fSCL)

—

s

SDL/SCL fall time

—

s

Stop condition setup time

1/2(2.2 * fSCL)

s

1

SCL frequency is given by SCL = BRGCLK_frequency / ((BRG register + 3) × pre_scaler × 2).

The ratio SYNCCLK/(BRGCLK / pre_scaler) must be greater than or equal to 4/1.

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

64

Freescale Semiconductor

UTOPIA AC Electrical Specifications

2

Figure 69 shows the I C bus timing.

SDA

202

203

204

208

205

207

SCL

206

209

210

211

2

Figure 69. I C Bus Timing Diagram

12 UTOPIA AC Electrical Specifications

Table 28 shows the AC electrical specifications for the UTOPIA interface.

Table 28. UTOPIA AC Electrical Specifications

Num

Signal Characteristic

Direction

Min

Max

Unit

U1

UtpClk rise/fall time (Internal clock option)

Output

—

50

—

40

—

2

3.5

50

3.5

60

50

16

—

ns

%

Duty cycle

Frequency

MHz

ns

U1a UtpClk rise/fall time (external clock option)

Input

Duty cycle

Frequency

%

MHz

ns

U2

U3

U4

U5

RxEnb and TxEnb active delay

Output

Input

UTPB, SOC, Rxclav and Txclav setup time

UTPB, SOC, Rxclav and Txclav hold time

8

ns

Input

1

—

ns

UTPB, SOC active delay (and PHREQ and PHSEL active delay in

MPHY mode)

Output

2

16

ns

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

65

UTOPIA AC Electrical Specifications

Figure 70 shows signal timings during UTOPIA receive operations.

U1

UtpClk

U5

PHREQn

U3

3

U4

4

RxClav

U2

2

RxEnb

U3

3

U4

UTPB

SOC

Figure 70. UTOPIA Receive Timing

Figure 71 shows signal timings during UTOPIA transmit operations.

U1

1

UtpClk

U5

5

PHSELn

U4

4

U3

3

TxClav

U2

2

TxEnb

U5

5

UTPB

SOC

Figure 71. UTOPIA Transmit Timing

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

66

Freescale Semiconductor

FEC Electrical Characteristics

13 FEC Electrical Characteristics

This section provides the AC electrical specifications for the Fast Ethernet controller (FEC). Note that the

timing specifications for the MII signals are independent of system clock frequency (part speed

designation). Also, MII signals use TTL signal levels compatible with devices operating at either 5.0 V or

3.3 V.

13.1 MII Receive Signal Timing (MII_RXD[3:0], MII_RX_DV, MII_RX_ER,

MII_RX_CLK)

The receiver functions correctly up to a MII_RX_CLK maximum frequency of 25 MHz + 1%. There is no

minimum frequency requirement. In addition, the processor clock frequency must exceed the

MII_RX_CLK frequency – 1%.

Table 29 provides information on the MII receive signal timing.

Table 29. MII Receive Signal Timing

Num

Characteristic

Min

Max

Unit

M1

M2

M3

MII_RXD[3:0], MII_RX_DV, MII_RX_ER to MII_RX_CLK setup

MII_RX_CLK to MII_RXD[3:0], MII_RX_DV, MII_RX_ER hold

MII_RX_CLK pulse width high

5

—

ns

35%

65%

MII_RX_CLK

period

M4

MII_RX_CLK pulse width low

35%

65%

MII_RX_CLK

period

Figure 72 shows MII receive signal timing.

M3

MII_RX_CLK (Input)

M4

MII_RXD[3:0] (Inputs)

MII_RX_DV

MII_RX_ER

M1

M2

Figure 72. MII Receive Signal Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

67

FEC Electrical Characteristics

13.2 MII Transmit Signal Timing (MII_TXD[3:0], MII_TX_EN,

MII_TX_ER, MII_TX_CLK)

The transmitter functions correctly up to a MII_TX_CLK maximum frequency of 25 MHz +1%. There is

no minimum frequency requirement. In addition, the processor clock frequency must exceed the

MII_TX_CLK frequency – 1%.

Table 30 provides information on the MII transmit signal timing.

Table 30. MII Transmit Signal Timing

Num

Characteristic

Min

Max

Unit

M5

M6

M7

MII_TX_CLK to MII_TXD[3:0], MII_TX_EN, MII_TX_ER invalid

MII_TX_CLK to MII_TXD[3:0], MII_TX_EN, MII_TX_ER valid

MII_TX_CLK pulse width high

5

—

25

ns

—

35

65%

MII_TX_CLK

period

M8

MII_TX_CLK pulse width low

35%

65%

MII_TX_CLK

period

Figure 73 shows the MII transmit signal timing diagram.

M7

MII_TX_CLK (Input)

RMII_REFCLK

M5

M8

MII_TXD[3:0] (Outputs)

MII_TX_EN

MII_TX_ER

M6

Figure 73. MII Transmit Signal Timing Diagram

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

68

Freescale Semiconductor

FEC Electrical Characteristics

13.3 MII Async Inputs Signal Timing (MII_CRS, MII_COL)

Table 31 provides information on the MII async inputs signal timing.

Table 31. MII Async Inputs Signal Timing

Num

Characteristic

Min

Max

Unit

M9

MII_CRS, MII_COL minimum pulse width

1.5

—

MII_TX_CLK

period

Figure 74 shows the MII asynchronous inputs signal timing diagram.

MII_CRS, MII_COL

M9

Figure 74. MII Async Inputs Timing Diagram

13.4 MII Serial Management Channel Timing (MII_MDIO, MII_MDC)

Table 32 provides information on the MII serial management channel signal timing. The FEC functions

correctly with a maximum MDC frequency in excess of 2.5 MHz. The exact upper bound is under

investigation.

Table 32. MII Serial Management Channel Timing

Num

Characteristic

Min

Max

Unit

M10 MII_MDC falling edge to MII_MDIO output invalid (minimum propagation

delay)

0

—

ns

M11 MII_MDC falling edge to MII_MDIO output valid (max prop delay)

M12 MII_MDIO (input) to MII_MDC rising edge setup

M13 MII_MDIO (input) to MII_MDC rising edge hold

M14 MII_MDC pulse width high

—

10

25

—

ns

0

—

40%

60%

MII_MDC

period

M15 MII_MDC pulse width low

40%

60%

MII_MDC

period

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

69

Mechanical Data and Ordering Information

Figure 75 shows the MII serial management channel timing diagram.

M14

MM15

MII_MDC (Output)

MII_MDIO (Output)

M10

M11

MII_MDIO (Input)

M12

M13

Figure 75. MII Serial Management Channel Timing Diagram

14 Mechanical Data and Ordering Information

14.1 Ordering Information

Table 33 provides information on the MPC860 Revision D.4 derivative devices.

Table 33. MPC860 Family Revision D.4 Derivatives

2

Number of Ethernet Support

Multichannel

HDLC Support Support

ATM

Device

1

SCCs

(Mbps)

MPC855T

1

2

10/100

10

Yes

N/A

Yes

N/A

Yes

N/A

Yes

N/A

Yes

MPC860DE

MPC860DT

MPC860DP

MPC860EN

MPC860SR

MPC860T

10/100

10

4

10

10/100

MPC860P

1

Serial communications controller (SCC)

Up to 4 channels at 40 MHz or 2 channels at 25 MHz

2

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

70

Freescale Semiconductor

Mechanical Data and Ordering Information

Table 34 identifies the packages and operating frequencies available for the MPC860.

Table 34. MPC860 Family Package/Frequency Availability

Freq. (MHz) /

Temp. (Tj)

Package Type

Package

Order Number

1

Ball grid array

50

ZP/ZQ

MPC855TZQ50D4

MPC860DEZQ50D4

MPC860DTZQ50D4

MPC860ENZQ50D4

MPC860SRZQ50D4

MPC860TZQ50D4

MPC860DPZQ50D4

MPC860PZQ50D4

ZP suffix—leaded

ZQ suffix—leaded

VR suffix—lead-free

0° to 95°C

Tape and Reel

MPC855TZQ50D4R2

MPC860DEZQ50D4R2

MPC860ENZQ50D4R2

MPC860SRZQ50D4R2

MPC860TZQ50D4R2

MPC860DPZQ50D4R2

MC860ENCVR50D4R2

MPC855TVR50D4R2

MPC860ENVR50D4R2

MPC860SRVR50D4R2

MPC860TVR50D4R2

VR

MPC855TCVR50D4

MPC855TVR50D4

MPC860DEVR50D4

MPC860DPVR50D4

MPC860DTVR50D4

MPC860ENVR50D4

MPC860PVR50D4

MPC860SRVR50D4

MPC860TVR50D4

1

66

ZP/ZQ

MPC855TZQ66D4

MPC860DEZQ66D4

MPC860DTZQ66D4

MPC860ENZQ66D4

MPC860SRZQ66D4

MPC860TZQ66D4

MPC860DPZQ66D4

MPC860PZQ66D4

0° to 95°C

Tape and Reel

VR

MPC860SRZQ66D4R2

MPC860PZQ66D4R2

MPC855TCVR66D4

MPC855TVR66D4

MPC860DEVR66D4

MPC860DPVR66D4

MPC860DTVR66D4

MPC860ENVR66D4

MPC860PVR66D4

MPC860SRVR66D4

MPC860TVR66D4

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

71

Mechanical Data and Ordering Information

Table 34. MPC860 Family Package/Frequency Availability (continued)

Freq. (MHz) /

Temp. (Tj)

Package Type

Ball grid array (continued)

ZP suffix—leaded

ZQ suffix—leaded

VR suffix—lead-free

Package

Order Number

1

80

ZP/ZQ

MPC855TZQ80D4

MPC860DEZQ80D4

MPC860DTZQ80D4

MPC860ENZQ80D4

MPC860SRZQ80D4

MPC860TZQ80D4

MPC860DPZQ80D4

MPC860PZQ80D4

0° to 95°C

Tape and Reel

VR

MPC860PZQ80D4R2

MPC860PVR80D4R2

MPC855TVR80D4

MPC860DEVR80D4

MPC860DPVR80D4

MPC860ENVR80D4

MPC860PVR80D4

MPC860SRVR80D4

MPC860TVR80D4

1

Ball grid array (CZP suffix)

CZP suffix—leaded

CZQ suffix—leaded

50

ZP/ZQ

MPC855TCZQ50D4

MPC860DECZQ50D4

MPC860DTCZQ50D4

MPC860ENCZQ50D4

MPC860SRCZQ50D4

MPC860TCZQ50D4

MPC860DPCZQ50D4

MPC860PCZQ50D4

–40° to 95°C

CVR suffix—lead-free

Tape and Reel

CVR

MPC855TCZQ50D4R2

MC860ENCVR50D4R2

MPC860DECVR50D4

MPC860DTCVR50D4

MPC860ENCVR50D4

MPC860PCVR50D4

MPC860SRCVR50D4

MPC860TCVR50D4

1

66

ZP/ZQ

MPC855TCZQ66D4

MPC860ENCZQ66D4

MPC860SRCZQ66D4

MPC860TCZQ66D4

MPC860DPCZQ66D4

MPC860PCZQ66D4

–40° to 95°C

CVR

MPC860DTCVR66D4

MPC860ENCVR66D4

MPC860PCVR66D4

MPC860SRCVR66D4

MPC860TCVR66D4

1

The ZP package is no longer recommended for use. The ZQ package replaces the ZP package.

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

72

Freescale Semiconductor

Mechanical Data and Ordering Information

14.2 Pin Assignments

Figure 76 shows the top view pinout of the PBGA package. For additional information, see the MPC860

PowerQUICC User’s Manual, or the MPC855T User’s Manual.

NOTE: This is the top view of the device.

W

PD10 PD8

PD14 PD13 PD9

PA0 PB14 PD15

PD3

IRQ7 D0

D4

D1

D2

D10

D11

D9

D3

D5

VDDL

D20

D6

D7

D29

DP1

DP2 CLKOUT IPA3

V

U

T

VSSSYN1

N/C

PD6 M_Tx_EN IRQ0 D13

D27

D23

D17

D14

D16

D15

D18

D19

D22

D24

D26

D31

D28

D30

DP3

DP0

PD4

PD5 IRQ1

D8

D21

IPA5 IPA4 IPA2

N/C VSSSYN

XFC VDDSYN

PA1

PC6

PC5

PC4 PD11

PD7 VDDH D12

VDDH

D25

IPA6 IPA0 IPA1 IPA7

R

P

N

M

L

VDDH

WAIT_B WAIT_A

VDDL RSTCONF

PA2 PB15 PD12

KAPWR

PORESET

SRESET

PA4 PB17 PA3 VDDL

PB19 PA5 PB18 PB16

GND

XTAL

TEXP

HRESET

EXTCLK EXTAL

PA7

PC8

PA6

PC7

BADDR28

MODCK2

OP0

BADDR29 VDDL

OP1 MODCK1

PB22 PC9

PA8 PB20

AS

K

J

PC10 PA9 PB23 PB21

PC11 PB24 PA10 PB25

GND

BADDR30 IPB6 ALEA IRQ4

IPB5 IPB1 IPB2 ALEB

M_COL IRQ2 IPB0 IPB7

H

G

F

VDDL M_MDIO TDI

TCK

TRST TMS TDO PA11

PB26 PC12 PA12 VDDL

PB27 PC13 PA13 PB29

PB28 PC14 PA14 PC15

BR

VDDL

CS3

IRQ6 IPB4 IPB3

GND

TS

BI

IRQ3 BURST

VDDH

CS6

E

D

C

B

A

BG

BB

A8

A9

N/C

A12

A13

N/C

A16

A17

A15

A20

A21

A19

A24

A23

A25

A18 BSA0 GPLA0 N/C

CS2 GPLA5 BDIP TEA

PB30 PA15 PB31

A3

A6

A26 TSIZ1 BSA1 WE0 GPLA1 GPLA3 CS7

CS0

TA GPLA4

A0

19

A1

A4

A10

A22 TSIZ0 BSA3 M_CRS WE2 GPLA2 CS5 CE1A WR GPLB4

A2

18

A5

17

A7

16

A11

15

A14

14

A27

13

A29

12

A30

11

A28

10

A31 VDDL BSA2 WE1 WE3 CS4 CE2A CS1

9

8

7

6

5

4

3

2

1

Figure 76. Pinout of the PBGA Package

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

73

Mechanical Data and Ordering Information

14.3 Mechanical Dimensions of the PBGA Package

Figure 77 shows the mechanical dimensions of the ZP PBGA package.

C

0.2

4X

0.2 C

0.25 C

0.35 C

D

A

E2

E

D2

B

TOP VIEW

A2

A3

A1

A

D1

SIDE VIEW

18X e

W

V

U

T

R

P

N

M

L

K

J

E1

H

G

F

MILLIMETERS

E

D

C

B

A

DIM MIN

MAX

2.05

0.70

1.35

0.90

A

A1

A2

A3

b

---

0.50

0.95

0.70

0.60

1

3

5

7

9

11 13 15 17 19

2

4 6 8 10 12 14 16 18

357X

b

BOTTOM VIEW

M

0.3

C A B

C

D

25.00 BSC

22.86 BSC

M

0.15

D1

D2

e

22.40

22.60

1.27 BSC

25.00 BSC

22.86 BSC

E

NOTE

E1

E2

1. Dimensions and tolerance per ASME Y14.5M, 1994.

22.40

22.60

2. Dimensions in millimeters.

3. Dimension b is the maximum solder ball diameter

measured parallel to data C.

Figure 77. Mechanical Dimensions and Bottom Surface Nomenclature of the ZP PBGA Package

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

74

Freescale Semiconductor

Mechanical Data and Ordering Information

Figure 78 shows the mechanical dimensions of the ZQ PBGA package.

NOTE

1. All Dimensions in millimeters.

2. Dimensions and tolerance per ASME Y14.5M, 1994.

3. Maximum Solder Ball Diameter measured parallel to Datum A.

4.

Datum A, the seating plane, is defined by the spherical crowns of the solder balls.

Figure 78. Mechanical Dimensions and Bottom Surface Nomenclature of the ZQ PBGA Package

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

75

Document Revision History

15 Document Revision History

Table 35 lists significant changes between revisions of this hardware specification.

Table 35. Document Revision History

Revision

Date

Changes

9

10/2011

Updated orderable part numbers in Table 34, “MPC860 Family Package/Frequency

Availability.”

8

08/2007

• Updated template.

• On page 1, added a second paragraph.

• After Table 2, inserted a new figure showing the undershoot/overshoot voltage

(Figure 1) and renumbered the rest of the figures.

• In Figure 3, changed all reference voltage measurement points from 0.2 and 0.8 V to

50% level.

• In Table 16, changed num 46 description to read, “TA assertion to rising edge ...”

• In Figure 46, changed TA to reflect the rising edge of the clock.

7.0

9/2004

• Added a tablefootnote to Table 6 DC Electrical Specifications about meeting the VIL

Max of the I2C Standard

• Replaced the thermal characteristics in Table 4 by the ZQ package

• Add the new parts to the Ordering and Availablity Chart in Table 34

• Added the mechanical spec of the ZQ package in Figure 78

• Removed all of the old revisions from Table 5

6.3

6.2

9/2003

8/2003

• •Added Section 11.2 on the Port C interrupt pins

• •Nontechnical reformatting

• Changed B28a through B28d and B29d to show that TRLX can be 0 or 1

• Changed reference documentation to reflect the Rev 2 MPC860 PowerQUICC Family

Users Manual

• Nontechnical reformatting

6.1

11/2002

• Corrected UTOPIA RXenb* and TXenb* timing values

• Changed incorrect usage of Vcc to Vdd

• Corrected dual port RAM to 8 Kbytes

6

10/2002

11/2001

• Added the MPC855T. Corrected Figure 26 on page -36.

5.1

• Revised template format, removed references to MAC functionality, changed Table 7

B23 max value @ 66 MHz from 2ns to 8ns, added this revision history table

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

76

Freescale Semiconductor

Document Revision History

MPC860 PowerQUICC Family Hardware Specifications, Rev. 9

Freescale Semiconductor

77

How to Reach Us:

Home Page:

www.freescale.com

Web Support:

http://www.freescale.com/support

USA/Europe or Locations Not Listed:

Freescale Semiconductor, Inc.

Technical Information Center, EL516

2100 East Elliot Road

Tempe, Arizona 85284

1-800-521-6274 or

Information in this document is provided solely to enable system and software

implementers to use Freescale Semiconductor products. There are no express or

implied copyright licenses granted hereunder to design or fabricate any integrated

circuits or integrated circuits based on the information in this document.

+1-480-768-2130

www.freescale.com/support

Freescale Semiconductor reserves the right to make changes without further notice to

any products herein. Freescale Semiconductor makes no warranty, representation or

guarantee regarding the suitability of its products for any particular purpose, nor does

Freescale Semiconductor assume any liability arising out of the application or use of

any product or circuit, and specifically disclaims any and all liability, including without

limitation consequential or incidental damages. “Typical” parameters which may be

provided in Freescale Semiconductor data sheets and/or specifications can and do

vary in different applications and actual performance may vary over time. All operating

parameters, including “Typicals” must be validated for each customer application by

customer’s technical experts. Freescale Semiconductor does not convey any license

under its patent rights nor the rights of others. Freescale Semiconductor products are

not designed, intended, or authorized for use as components in systems intended for

surgical implant into the body, or other applications intended to support or sustain life,

or for any other application in which the failure of the Freescale Semiconductor product

could create a situation where personal injury or death may occur. Should Buyer

purchase or use Freescale Semiconductor products for any such unintended or

unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor

and its officers, employees, subsidiaries, affiliates, and distributors harmless against all

claims, costs, damages, and expenses, and reasonable attorney fees arising out of,

directly or indirectly, any claim of personal injury or death associated with such

unintended or unauthorized use, even if such claim alleges that Freescale

Europe, Middle East, and Africa:

Freescale Halbleiter Deutschland GmbH

Technical Information Center

Schatzbogen 7

81829 Muenchen, Germany

+44 1296 380 456 (English)

+46 8 52200080 (English)

+49 89 92103 559 (German)

+33 1 69 35 48 48 (French)

www.freescale.com/support

Japan:

Freescale Semiconductor Japan Ltd.

Headquarters

ARCO Tower 15F

1-8-1, Shimo-Meguro, Meguro-ku

Tokyo 153-0064

Japan

0120 191014 or

+81 3 5437 9125

support.japan@freescale.com

Asia/Pacific:

Freescale Semiconductor China Ltd.

Exchange Building 23F

No. 118 Jianguo Road

Chaoyang District

Semiconductor was negligent regarding the design or manufacture of the part.

Beijing 100022

China

+86 10 5879 8000

support.asia@freescale.com

Freescale, the Freescale logo, CodeWarrior, ColdFire, PowerQUICC,

QorIQ, StarCore, and Symphony are trademarks of Freescale

Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. CoreNet, QorIQ Qonverge,

QUICC Engine, and VortiQa are trademarks of Freescale Semiconductor,

Inc. All other product or service names are the property of their respective

owners. The Power Architecture and Power.org word marks and the Power

and Power.org logos and related marks are trademarks and service marks

licensed by Power.org.

Document Number: MPC860EC

Rev. 9

02/2012


型号：	KMPC860TCZQ66D4
厂家：	NXP
描述：	KMPC860TCZQ66D4 PC
文件：	总78页 (文件大小：529K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

KMPC860TCZQ66D4 [NXP]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E