LPC2292FET144 [NXP]
IC 32-BIT, FLASH, 60 MHz, RISC MICROCONTROLLER, PBGA144, 12 X 12 MM, 0.80 MM HEIGHT, PLASTIC, MO-216, SOT-569-1, TFBGA-144, Microcontroller;型号: | LPC2292FET144 |
厂家: | NXP |
描述: | IC 32-BIT, FLASH, 60 MHz, RISC MICROCONTROLLER, PBGA144, 12 X 12 MM, 0.80 MM HEIGHT, PLASTIC, MO-216, SOT-569-1, TFBGA-144, Microcontroller 时钟 微控制器 外围集成电路 |
文件: | 总53页 (文件大小:261K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LPC2292/LPC2294
16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with
CAN, 10-bit ADC and external memory interface
Rev. 7 — 4 December 2008
Product data sheet
1. General description
The LPC2292/LPC2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU
with real-time emulation and embedded trace support, together with 256 kB of embedded
high-speed flash memory. A 128-bit wide memory interface and a unique accelerator
architecture enable 32-bit code execution at the maximum clock rate. For critical code size
applications, the alternative 16-bit Thumb mode reduces code by more than 30 % with
minimal performance penalty.
With their 144-pin package, low power consumption, various 32-bit timers, 8-channel
10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine
external interrupt pins these microcontrollers are particularly suitable for automotive and
industrial control applications as well as medical systems and fault-tolerant maintenance
buses. The number of available GPIOs ranges from 76 (with external memory) through
112 (single-chip). With a wide range of additional serial communications interfaces, they
are also suited for communication gateways and protocol converters as well as many
other general-purpose applications.
Remark: Throughout the data sheet, the term LPC2292/LPC2294 will apply to devices
with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate
from other devices only when necessary.
2. Features
2.1 Key features brought by LPC2292/LPC2294/01 devices
I Fast GPIO ports enable port pin toggling up to 3.5 times faster than the original device.
They also allow for a port pin to be read at any time regardless of its function.
I Dedicated result registers for ADC(s) reduce interrupt overhead. The ADC pads are
5 V tolerant when configured for digital I/O function(s).
I UART0/1 include fractional baud rate generator, auto-bauding capabilities and
handshake flow-control fully implemented in hardware.
I Buffered SSP serial controller supporting SPI, 4-wire SSI, and Microwire formats.
I SPI programmable data length and master mode enhancement.
I Diversified Code Read Protection (CRP) enables different security levels to be
implemented. This feature is available in LPC2292/LPC2294/00 devices as well.
I General purpose timers can operate as external event counters.
2.2 Key features common for all devices
I 16/32-bit ARM7TDMI-S microcontroller in a LQFP144 package.
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
I 16 kB on-chip static RAM and 256 kB on-chip flash program memory. 128-bit wide
interface/accelerator enables high-speed 60 MHz operation.
I In-System Programming/In-Application Programming (ISP/IAP) via on-chip bootloader
software. Single flash sector or full chip erase in 400 ms and programming of 256 B in
1 ms.
I EmbeddedICE-RT and Embedded Trace interfaces offer real-time debugging with the
on-chip RealMonitor software as well as high-speed real-time tracing of instruction
execution.
I Two/four (LPC2292/LPC2294) interconnected CAN interfaces with advanced
acceptance filters. Additional serial interfaces include two UARTs (16C550), Fast
I2C-bus (400 kbit/s) and two SPIs.
I Eight channel 10-bit ADC with conversion time as low as 2.44 µs.
I Two 32-bit timers (with four capture and four compare channels), PWM unit (six
outputs), Real-Time Clock (RTC), and watchdog.
I Vectored Interrupt Controller (VIC) with configurable priorities and vector addresses.
I Configurable external memory interface with up to four banks, each up to 16 MB and
8/16/32-bit data width.
I Up to 112 general purpose I/O pins (5 V tolerant). Up to nine edge/level sensitive
external interrupt pins available.
I 60 MHz maximum CPU clock available from programmable on-chip PLL with settling
time of 100 µs.
I The on-chip crystal oscillator should have an operating range of 1 MHz to 25 MHz.
I Power saving modes include Idle and Power-down.
I Processor wake-up from Power-down mode via external interrupt.
I Individual enable/disable of peripheral functions for power optimization.
I Dual power supply:
N CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ± 0.15 V).
N I/O power supply range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads.
3. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
LPC2292FBD144
LQFP144
plastic low profile quad flat package;
SOT486-1
144 leads; body 20 × 20 × 1.4 mm
LPC2292FBD144/00
LPC2292FBD144/01
LPC2292FET144/00
LPC2292FET144/01
LPC2292FET144/G
LQFP144
LQFP144
plastic low profile quad flat package;
144 leads; body 20 × 20 × 1.4 mm
SOT486-1
SOT486-1
plastic low profile quad flat package;
144 leads; body 20 × 20 × 1.4 mm
TFBGA144 plastic thin fine-pitch ball grid array package; SOT569-2
144 balls; body 12 × 12 × 0.8 mm
TFBGA144 plastic thin fine-pitch ball grid array package; SOT569-2
144 balls; body 12 × 12 × 0.8 mm
TFBGA144 plastic thin fine-pitch ball grid array package; SOT569-2
144 balls; body 12 × 12 × 0.8 mm
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
2 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 1.
Ordering information …continued
Type number
Package
Name
Description
Version
LPC2294HBD144
LQFP144
plastic low profile quad flat package;
SOT486-1
144 leads; body 20 × 20 × 1.4 mm
LPC2294HBD144/00
LPC2294HBD144/01
LQFP144
LQFP144
plastic low profile quad flat package;
144 leads; body 20 × 20 × 1.4 mm
SOT486-1
SOT486-1
plastic low profile quad flat package;
144 leads; body 20 × 20 × 1.4 mm
3.1 Ordering options
Table 2.
Ordering options
Type number
Flash
memory
RAM
CAN
Fast GPIO/
SSP/
Temperature range
Enhanced
UART, ADC,
Timer
LPC2292FBD144
256 kB
16 kB
16 kB
16 kB
16 kB
16 kB
16 kB
16 kB
16 kB
16 kB
2 channels no
2 channels no
2 channels yes
2 channels no
2 channels yes
2 channels no
4 channels no
4 channels no
4 channels yes
−40 °C to +85 °C
−40 °C to +85 °C
−40 °C to +85 °C
−40 °C to +85 °C
−40 °C to +85 °C
−40 °C to +85 °C
−40 °C to +125 °C
−40 °C to +125 °C
−40 °C to +125 °C
LPC2292FBD144/00 256 kB
LPC2292FBD144/01 256 kB
LPC2292FET144/00 256 kB
LPC2292FET144/01 256 kB
LPC2292FET144/G 256 kB
LPC2294HBD144
256 kB
LPC2294HBD144/00 256 kB
LPC2294HBD144/01 256 kB
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
3 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
4. Block diagram
(1)
(1)
TMS
(1)
TDI
(1)
XTAL2
(1)
TRST
TCK
TDO
XTAL1 RESET
LPC2292
LPC2294
TEST/DEBUG
INTERFACE
SYSTEM
FUNCTIONS
PLL
ARM7TDMI-S
HIGH-SPEED
GPIO
48 PINS TOTAL
system
clock
(4)
P0, P1
VECTORED
INTERRUPT
CONTROLLER
AHB BRIDGE
AMBA AHB
(Advanced High-performance Bus)
ARM7 local bus
INTERNAL
SRAM
INTERNAL
FLASH
CONTROLLER
CONTROLLER
AHB
DECODER
(2)
CS3 to CS0
(2)
16 kB
SRAM
256 kB
FLASH
AHB TO APB
BRIDGE
APB
DIVIDER
A23 to A0
EXTERNAL MEMORY
CONTROLLER
(2)
BLS3 to BLS0
(2)
OE, WE
APB (advanced
peripheral bus)
EXTERNAL
(2)
EINT3 to EINT0
D31 to D0
INTERRUPTS
SCL
2
I C-BUS SERIAL
INTERFACE
4 × CAP0
4 × CAP1
4 × MAT0
4 × MAT1
SDA
CAPTURE/
COMPARE
TIMER 0/TIMER 1
SCK1
MOSI1
MISO1
SSEL1
(4)
SPI1/SSP
SERIAL INTERFACE
AIN3 to AIN0
AIN7 to AIN4
A/D CONVERTER
SCK0
SPI0
MOSI0
MISO0
SSEL0
SERIAL INTERFACE
P0[30:0]
P1[31:16], P1[1:0]
P2[31:0]
GENERAL
PURPOSE I/O
TXD0, TXD1
RXD0, RXD1
P3[31:0]
UART0/UART1
DSR1, CTS1,
DCD1, RI1
PWM6 to PWM1
PWM0
TD2, TD1
RD2, RD1
TD4, TD3
CAN
(3)
REAL-TIME CLOCK
SYSTEM CONTROL
(3)
RD4, RD3
WATCHDOG
TIMER
002aad184
(1) When test/debug interface is used, GPIO/other functions sharing these pins are not available.
(2) Pins shared with GPIO.
(3) Available in LPC2294 only.
(4) SSP interface and high-speed GPIO are available on LPC2292/2294/01 only.
Fig 1. Block diagram
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
4 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
5. Pinning information
5.1 Pinning
1
108
LPC2292FBD
LPC2294HBD(1)
36
73
002aad185
(1) Pin configuration is identical for devices with and without /00 and /01 suffixes.
Fig 2. LQFP144 pinning
ball A1
index area
LPC2292FET144(1)
1
2 3 4 5 6 7 8 9 10 11 12 13
A
B
C
D
E
F
G
H
J
K
L
M
N
002aad191
Transparent top view
(1) Pin configuration is identical for devices with and without /00 and /01 suffixes.
Fig 3. TFBGA144 pinning
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
5 of 53
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 3.
Ball allocation
Row Column
1
2
3
4
5
6
7
8
9
10
11
12
13
A
P2[22]/
D22
VDDA(1V8) P1[28]/
TDI
P2[21]/
D21
P2[18]/
D18
P2[14]/
D14
P1[29]/
TCK
P2[11]/
D11
P2[10]/
D10
P2[7]/D7 VDD(3V3)
VDD(1V8)
P2[4]/D4
B
VDD(3V3)
P1[27]/
TDO
XTAL2
VSSA(PLL) P2[19]/
D19
P2[15]/
D15
P2[12]/
D12
P0[20]/
MAT1[3]/
SSEL1/
EINT3
VDD(3V3)
P2[6]/D6 VSS
P2[3]/D3 VSS
C
D
E
P0[21]/
PWM5/
CAP1[3]
VSS
XTAL1
VSSA
RESET
P2[16]/
D16
P2[13]/
D13
P0[19]/
P2[9]/D9 P2[5]/D5 P2[2]/D2 P2[1]/D1 VDD(3V3)
MAT1[2]/
MOSI1/
CAP1[2]
P0[24]/
TD2
P1[19]/
TRACE
PKT3
P0[23]/
RD2
P0[22]/
CAP0[0]/ D20
MAT0[0]
P2[20]/
P2[17]/
D17
VSS
P0[18]/
P2[8]/D8 P1[30]/
TMS
VSS
P1[20]/
TRACE
SYNC
P0[17]/
CAP1[2]/
SCK1/
CAP1[3]/
MISO1/
MAT1[3]
MAT1[2]
P2[25]/
D25
P2[24]/
D24
P2[23]
VSS
P0[16]/
EINT0/
P0[15]/
RI1/
P2[0]/D0 P3[30]/
BLS1
MAT0[2]/ EINT2
CAP0[2]
F
P2[27]/
D27/
BOOT1
P1[18]/
TRACE
PKT2
VDDA(3V3) P2[26]/
D26/
P3[31]/
BLS0
P1[21]/
PIPE
STAT0
VDD(3V3)
VSS
BOOT0
G
H
P2[29]/
D29
P2[28]/
D28
P2[30]/
D30/AIN4 D31/AIN5
P2[31]/
P0[14]/
DCD1/
EINT1
P1[0]/CS0 P3[0]/A0 P1[1]/OE
P0[25]/
RD1
TD1
P0[27]/
AIN0/
P1[17]/
TRACE
P0[13]/
DTR1/
P1[22]/
PIPE
P3[2]/A2 P3[1]/A1
CAP0[1]/ PKT1
MAT0[1]
MAT1[1]
STAT1
J
P0[28]/
AIN1/
CAP0[2]/
MAT0[2]
VSS
P3[29]/
BLS2/
AIN6
P3[28]/
BLS3/
AIN7
P3[3]/A3 P1[23]/
PIPE
P0[11]/
CTS1/
CAP1[1]
P0[12]/
DSR1/
MAT1[0]
STAT2
K
P3[27]/
WE
P3[26]/
CS1
VDD(3V3)
P3[22]/
A22
P3[20]/
A20
P0[1]/
P3[14]/
A14
P1[25]/
EXTIN0
P3[11]/
A11
VDD(3V3)
P0[10]/
RTS1/
CAP1[0]
VSS
P3[4]/A4
RXD0/
PWM3/
EINT0
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Ball allocation …continued
Table 3.
Row Column
1
2
3
4
5
6
7
8
9
10
11
12
13
L
P0[29]/
AIN2/
CAP0[3]/ EINT3/
P0[30]/
AIN3/
P1[16]/
TRACE
PKT0
P0[0]/
TXD0/
PWM1
P3[19]/
A19
P0[2]/
SCL/
CAP0[0]
P3[15]/
A15
P0[4]/
SCK0/
CAP0[1]
P3[12]/
A12
VSS
P1[24]/
TRACE
CLK
P0[8]/
TXD1/
PWM4
P0[9]/
RXD1/
PWM6/
EINT3
MAT0[3]
CAP0[0]
M
N
P3[25]/
CS2
P3[24]/
CS3
VDD(3V3)
P1[31]/
TRST
P3[18]/
A18
VDD(3V3)
P3[16]/
A16
P0[3]/
SDA/
MAT0[0]/
EINT1
P3[13]/
A13
P3[9]/A9 P0[7]/
SSEL0/
P3[7]/A7 P3[5]/A5
P3[8]/A8 P3[6]/A6
PWM2/
EINT2
VDD(1V8)
VSS
P3[23]/
A23/
XCLK
P3[21]/
A21
P3[17]/
A17
P1[26]/
RTCK
VSS
VDD(3V3)
P0[5]/
MISO0/
MAT0[1]
P3[10]/
A10
P0[6]/
MOSI0/
CAP0[2]
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
5.2 Pin description
Table 4.
Symbol
Pin description
Pin (LQFP)
Pin
(TFBGA)[1]
Type
Description
P0[0] to P0[31]
I/O
Port 0: Port 0 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 0 pins
depends upon the pin function selected via the Pin Connect
Block.
Pins 26 and 31 of port 0 are not available.
TXD0 — Transmitter output for UART0.
PWM1 — Pulse Width Modulator output 1.
RXD0 — Receiver input for UART0.
P0[0]/TXD0/
PWM1
42[2]
49[4]
L4[2]
K6[4]
O
O
I
P0[1]/RXD0/
PWM3/EINT0
O
I
PWM3 — Pulse Width Modulator output 3.
EINT0 — External interrupt 0 input
P0[2]/SCL/
CAP0[0]
50[5]
58[5]
L6[5]
I/O
SCL — I2C-bus clock input/output. Open-drain output (for
I2C-bus compliance).
I
CAP0[0] — Capture input for Timer 0, channel 0.
SDA — I2C-bus data input/output. Open-drain output (for
I2C-bus compliance).
P0[3]/SDA/
MAT0[0]/EINT1
M8[5]
I/O
O
I
MAT0[0] — Match output for Timer 0, channel 0.
EINT1 — External interrupt 1 input.
P0[4]/SCK0/
CAP0[1]
59[2]
61[2]
68[2]
69[4]
L8[2]
I/O
SCK0 — Serial clock for SPI0. SPI clock output from master
or input to slave.
I
CAP0[1] — Capture input for Timer 0, channel 1.
P0[5]/MISO0/
MAT0[1]
N9[2]
I/O
MISO0 — Master In Slave OUT for SPI0. Data input to SPI
master or data output from SPI slave.
O
MAT0[1] — Match output for Timer 0, channel 1.
P0[6]/MOSI0/
CAP0[2]
N11[2]
M11[4]
I/O
MOSI0 — Master Out Slave In for SPI0. Data output from SPI
master or data input to SPI slave.
I
I
CAP0[2] — Capture input for Timer 0, channel 2.
P0[7]/SSEL0/
PWM2/EINT2
SSEL0 — Slave Select for SPI0. Selects the SPI interface as
a slave.
O
I
PWM2 — Pulse Width Modulator output 2.
EINT2 — External interrupt 2 input.
P0[8]/TXD1/
PWM4
75[2]
76[4]
L12[2]
L13[4]
O
O
I
TXD1 — Transmitter output for UART1.
PWM4 — Pulse Width Modulator output 4.
RXD1 — Receiver input for UART1.
P0[9]/RXD1/
PWM6/EINT3
O
I
PWM6 — Pulse Width Modulator output 6.
EINT3 — External interrupt 3 input.
P0[10]/RTS1/
CAP1[0]
78[2]
83[2]
K11[2]
J12[2]
O
I
RTS1 — Request to Send output for UART1.
CAP1[0] — Capture input for Timer 1, channel 0.
CTS1 — Clear to Send input for UART1.
CAP1[1] — Capture input for Timer 1, channel 1.
P0[11]/CTS1/
CAP1[1]
I
I
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
8 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Symbol
Pin description …continued
Pin (LQFP)
Pin
(TFBGA)[1]
Type
Description
P0[12]/DSR1/
MAT1[0]/RD4
84[2]
J13[2]
H10[2]
G10[4]
I
DSR1 — Data Set Ready input for UART1.
MAT1[0] — Match output for Timer 1, channel 0.
RD4 — CAN4 receiver input (LPC2294 only).
DTR1 — Data Terminal Ready output for UART1.
MAT1[1] — Match output for Timer 1, channel 1.
TD4 — CAN4 transmitter output (LPC2294 only).
DCD1 — Data Carrier Detect input for UART1.
EINT1 — External interrupt 1 input.
O
I
P0[13]/DTR1/
MAT1[1]/TD4
85[2]
O
O
O
I
P0[14]/DCD1/
EINT1
92[4]
I
Note: LOW on this pin while RESET is LOW forces on-chip
bootloader to take over control of the part after reset.
P0[15]/RI1/
EINT2
99[4]
E11[4]
E10[4]
I
RI1 — Ring Indicator input for UART1.
I
EINT2 — External interrupt 2 input.
P0[16]/EINT0/
MAT0[2]/
CAP0[2]
100[4]
I
EINT0 — External interrupt 0 input.
O
MAT0[2] — Match output for Timer 0, channel 2.
CAP0[2] — Capture input for Timer 0, channel 2.
CAP1[2] — Capture input for Timer 1, channel 2.
SCK1 — Serial Clock for SPI1/SSP[3]. SPI clock output from
master or input to slave.
I
P0[17]/CAP1[2]/ 101[2]
SCK1/MAT1[2]
D13[2]
D8[2]
C8[2]
B8[4]
I
I/O
O
I
MAT1[2] — Match output for Timer 1, channel 2.
CAP1[3] — Capture input for Timer 1, channel 3.
MISO1 — Master In Slave Out for SPI1/SSP[3]. Data input to
P0[18]/CAP1[3]/ 121[2]
MISO1/MAT1[3]
I/O
SPI master or data output from SPI slave.
O
MAT1[3] — Match output for Timer 1, channel 3.
MAT1[2] — Match output for Timer 1, channel 2.
MOSI1 — Master Out Slave In for SPI1/SSP[3]. Data output
P0[19]/MAT1[2]/ 122[2]
MOSI1/CAP1[2]
O
I/O
from SPI master or data input to SPI slave.
I
CAP1[2] — Capture input for Timer 1, channel 2.
MAT1[3] — Match output for Timer 1, channel 3.
SSEL1 — Slave Select for SPI1/SSP[3]. Selects the SPI
P0[20]/MAT1[3]/ 123[4]
SSEL1/EINT3
O
I
interface as a slave.
I
EINT3 — External interrupt 3 input.
P0[21]/PWM5/ 4[2]
RD3/CAP1[3]
C1[2]
D4[2]
O
I
PWM5 — Pulse Width Modulator output 5.
RD3 — CAN3 receiver input (LPC2294 only).
CAP1[3] — Capture input for Timer 1, channel 3.
TD3 — CAN3 transmitter output (LPC2294 only).
CAP0[0] — Capture input for Timer 0, channel 0.
MAT0[0] — Match output for Timer 0, channel 0.
RD2 — CAN2 receiver input.
I
P0[22]/TD3/
CAP0[0]/
MAT0[0]
5[2]
O
I
O
I
P0[23]/RD2
P0[24]/TD2
P0[25]/RD1
6[2]
8[2]
21[2]
D3[2]
D1[2]
H1[2]
O
I
TD2 — CAN2 transmitter output.
RD1 — CAN1 receiver input.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
9 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Symbol
Pin description …continued
Pin (LQFP)
Pin
(TFBGA)[1]
Type
Description
P0[27]/AIN0/
CAP0[1]/
MAT0[1]
23[6]
H3[6]
J1[6]
L1[6]
L2[6]
I
AIN0 — ADC, input 0. This analog input is always connected
to its pin.
I
CAP0[1] — Capture input for Timer 0, channel 1.
MAT0[1] — Match output for Timer 0, channel 1.
O
I
P0[28]/AIN1/
CAP0[2]/
MAT0[2]
25[6]
32[6]
33[6]
AIN1 — ADC, input 1. This analog input is always connected
to its pin.
I
CAP0[2] — Capture input for Timer 0, channel 2.
MAT0[2] — Match output for Timer 0, channel 2.
O
I
P0[29]/AIN2/
CAP0[3]/
MAT0[3]
AIN2 — ADC, input 2. This analog input is always connected
to its pin.
I
CAP0[3] — Capture input for Timer 0, Channel 3.
MAT0[3] — Match output for Timer 0, channel 3.
O
I
P0[30]/AIN3/
AIN3 — ADC, input 3. This analog input is always connected
EINT3/CAP0[0]
to its pin.
I
EINT3 — External interrupt 3 input.
I
CAP0[0] — Capture input for Timer 0, channel 0.
P1[0] to P1[31]
I/O
Port 1: Port 1 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 1 pins
depends upon the pin function selected via the Pin Connect
Block.
Pins 2 through 15 of port 1 are not available.
CS0 — LOW-active Chip Select 0 signal.
P1[0]/CS0
P1[1]/OE
91[7]
G11[7]
O
(Bank 0 addresses range 0x8000 0000 to 0x80FF FFFF)
OE — LOW-active Output Enable signal.
90[7]
34[7]
G13[7]
L3[7]
O
O
P1[16]/
TRACEPKT0 — Trace Packet, bit 0. Standard I/O port with
TRACEPKT0
internal pull-up.
P1[17]/
TRACEPKT1
24[7]
15[7]
7[7]
H4[7]
F2[7]
O
O
O
O
TRACEPKT1 — Trace Packet, bit 1. Standard I/O port with
internal pull-up.
P1[18]/
TRACEPKT2
TRACEPKT2 — Trace Packet, bit 2. Standard I/O port with
internal pull-up.
P1[19]/
TRACEPKT3
D2[7]
D12[7]
TRACEPKT3 — Trace Packet, bit 3. Standard I/O port with
internal pull-up.
P1[20]/
102[7]
TRACESYNC — Trace Synchronization. Standard I/O port
TRACESYNC
with internal pull-up.
Note: LOW on this pin while RESET is LOW, enables pins
P1[25:16] to operate as Trace port after reset.
P1[21]/
PIPESTAT0
95[7]
86[7]
82[7]
70[7]
F11[7]
H11[7]
J11[7]
L11[7]
O
O
O
O
PIPESTAT0 — Pipeline Status, bit 0. Standard I/O port with
internal pull-up.
P1[22]/
PIPESTAT1
PIPESTAT1 — Pipeline Status, bit 1. Standard I/O port with
internal pull-up.
P1[23]/
PIPESTAT2
PIPESTAT2 — Pipeline Status, bit 2. Standard I/O port with
internal pull-up.
P1[24]/
TRACECLK — Trace Clock. Standard I/O port with internal
TRACECLK
pull-up.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
10 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Symbol
Pin description …continued
Pin (LQFP)
Pin
(TFBGA)[1]
Type
I
Description
P1[25]/EXTIN0 60[7]
K8[7]
N6[7]
EXTIN0 — External Trigger Input. Standard I/O with internal
pull-up.
P1[26]/RTCK
52[7]
I/O
RTCK — Returned Test Clock output. Extra signal added to
the JTAG port. Assists debugger synchronization when
processor frequency varies. Bidirectional pin with internal
pull-up.
Note: LOW on this pin while RESET is LOW, enables pins
P1[31:26] to operate as Debug port after reset.
P1[27]/TDO
P1[28]/TDI
P1[29]/TCK
144[7]
140[7]
126[7]
B2[7]
A3[7]
A7[7]
O
I
TDO — Test Data out for JTAG interface.
TDI — Test Data in for JTAG interface.
I
TCK — Test Clock for JTAG interface. This clock must be
slower than 1⁄6 of the CPU clock (CCLK) for the JTAG interface
to operate.
P1[30]/TMS
113[7]
43[7]
D10[7]
M4[7]
I
TMS — Test Mode Select for JTAG interface.
TRST — Test Reset for JTAG interface.
P1[31]/TRST
P2[0] to P2[31]
I
I/O
Port 2 — Port 2 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 2 pins
depends upon the pin function selected via the Pin Connect
Block.
P2[0]/D0
98[7]
E12[7]
C12[7]
C11[7]
B12[7]
A13[7]
C10[7]
B10[7]
A10[7]
D9[7]
C9[7]
A9[7]
A8[7]
B7[7]
C7[7]
A6[7]
B6[7]
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
D0 — External memory data line 0.
D1 — External memory data line 1.
D2 — External memory data line 2.
D3 — External memory data line 3.
D4 — External memory data line 4.
D5 — External memory data line 5.
D6 — External memory data line 6.
D7 — External memory data line 7.
D8 — External memory data line 8.
D9 — External memory data line 9.
D10 — External memory data line 10.
D11 — External memory data line 11.
D12 — External memory data line 12.
D13 — External memory data line 13.
D14 — External memory data line 14.
D15 — External memory data line 15.
D16 — External memory data line 16.
D17 — External memory data line 17.
D18 — External memory data line 18.
D19 — External memory data line 19.
D20 — External memory data line 20.
D21 — External memory data line 21.
D22 — External memory data line 22.
D23 — External memory data line 23.
P2[1]/D1
105[7]
106[7]
108[7]
109[7]
114[7]
115[7]
116[7]
117[7]
118[7]
120[7]
124[7]
125[7]
127[7]
129[7]
130[7]
131[7]
132[7]
133[7]
134[7]
136[7]
137[7]
1[7]
P2[2]/D2
P2[3]/D3
P2[4]/D4
P2[5]/D5
P2[6]/D6
P2[7]/D7
P2[8]/D8
P2[9]/D9
P2[10]/D10
P2[11]/D11
P2[12]/D12
P2[13]/D13
P2[14]/D14
P2[15]/D15
P2[16]/D16
P2[17]/D17
P2[18]/D18
P2[19]/D19
P2[20]/D20
P2[21]/D21
P2[22]/D22
P2[23]/D23
C6[7]
D6[7]
A5[7]
B5[7]
D5[7]
A4[7]
A1[7]
E3[7]
10[7]
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
11 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Symbol
Pin description …continued
Pin (LQFP)
Pin
(TFBGA)[1]
Type
Description
P2[24]/D24
P2[25]/D25
11[7]
12[7]
13[7]
E2[7]
E1[7]
F4[7]
I/O
I/O
I/O
I
D24 — External memory data line 24.
D25 — External memory data line 25.
D26 — External memory data line 26.
P2[26]/D26/
BOOT0
BOOT0 — While RESET is low, together with BOOT1 controls
booting and internal operation. Internal pull-up ensures high
state if pin is left unconnected.
P2[27]/D27/
BOOT1
16[7]
F1[7]
I/O
I
D27 — External memory data line 27.
BOOT1 — While RESET is low, together with BOOT0 controls
booting and internal operation. Internal pull-up ensures high
state if pin is left unconnected.
BOOT1:0 = 00 selects 8-bit memory on CS0 for boot.
BOOT1:0 = 01 selects 16-bit memory on CS0 for boot.
BOOT1:0 = 10 selects 32-bit memory on CS0 for boot.
BOOT1:0 = 11 selects internal flash memory.
D28 — External memory data line 28.
P2[28]/D28
P2[29]/D29
17[7]
18[7]
19[6]
G2[7]
G1[7]
G3[6]
I/O
I/O
I/O
I
D29 — External memory data line 29.
P2[30]/D30/
AIN4
D30 — External memory data line 30.
AIN4 — ADC, input 4. This analog input is always connected
to its pin.
P2[31]/D31/
AIN5
20[6]
G4[6]
I/O
I
D31 — External memory data line 31.
AIN5 — ADC, input 5. This analog input is always connected
to its pin.
P3[0] to P3[31]
I/O
Port 3 — Port 3 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 3 pins
depends upon the pin function selected via the Pin Connect
Block.
P3[0]/A0
89[7]
88[7]
87[7]
81[7]
80[7]
74[7]
73[7]
72[7]
71[7]
66[7]
65[7]
64[7]
63[7]
62[7]
56[7]
55[7]
53[7]
G12[7]
H13[7]
H12[7]
J10[7]
K13[7]
M13[7]
N13[7]
M12[7]
N12[7]
M10[7]
N10[7]
K9[7]
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
A0 — External memory address line 0.
A1 — External memory address line 1.
A2 — External memory address line 2.
A3 — External memory address line 3.
A4 — External memory address line 4.
A5 — External memory address line 5.
A6 — External memory address line 6.
A7 — External memory address line 7.
A8 — External memory address line 8.
A9 — External memory address line 9.
A10 — External memory address line 10.
A11 — External memory address line 11.
A12 — External memory address line 12.
A13 — External memory address line 13.
A14 — External memory address line 14.
A15 — External memory address line 15.
A16 — External memory address line 16.
P3[1]/A1
P3[2]/A2
P3[3]/A3
P3[4]/A4
P3[5]/A5
P3[6]/A6
P3[7]/A7
P3[8]/A8
P3[9]/A9
P3[10]/A10
P3[11]/A11
P3[12]/A12
P3[13]/A13
P3[14]/A14
P3[15]/A15
P3[16]/A16
L9[7]
M9[7]
K7[7]
L7[7]
M7[7]
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
12 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Symbol
Pin description …continued
Pin (LQFP)
Pin
(TFBGA)[1]
Type
Description
P3[17]/A17
P3[18]/A18
P3[19]/A19
P3[20]/A20
P3[21]/A21
P3[22]/A22
48[7]
47[7]
46[7]
45[7]
44[7]
41[7]
40[7]
N5[7]
M5[7]
L5[7]
K5[7]
N4[7]
K4[7]
N3[7]
O
O
O
O
O
O
I/O
O
O
A17 — External memory address line 17.
A18 — External memory address line 18.
A19 — External memory address line 19.
A20 — External memory address line 20.
A21 — External memory address line 21.
A22 — External memory address line 22.
A23 — External memory address line 23.
XCLK — Clock output.
P3[23]/A23/
XCLK
P3[24]/CS3
P3[25]/CS2
P3[26]/CS1
P3[27]/WE
36[7]
35[7]
30[7]
M2[7]
M1[7]
K2[7]
CS3 — LOW-active Chip Select 3 signal.
(Bank 3 addresses range 0x8300 0000 to 0x83FF FFFF)
CS2 — LOW-active Chip Select 2 signal.
(Bank 2 addresses range 0x8200 0000 to 0x82FF FFFF)
CS1 — LOW-active Chip Select 1 signal.
(Bank 1 addresses range 0x8100 0000 to 0x81FF FFFF)
WE — LOW-active Write enable signal.
O
O
29[7]
28[6]
K1[7]
J4[6]
O
O
I
P3[28]/BLS3/
AIN7
BLS3 — LOW-active Byte Lane Select signal (Bank 3).
AIN7 — ADC, input 7. This analog input is always connected
to its pin.
P3[29]/BLS2/
AIN6
27[6]
J3[6]
O
I
BLS2 — LOW-active Byte Lane Select signal (Bank 2).
AIN6 — ADC, input 6. This analog input is always connected
to its pin.
P3[30]/BLS1
P3[31]/BLS0
TD1
97[7]
96[7]
22[7]
135[8]
E13[7]
F10[7]
H2[7]
O
O
O
I
BLS1 — LOW-active Byte Lane Select signal (Bank 1).
BLS0 — LOW-active Byte Lane Select signal (Bank 0).
TD1: CAN1 transmitter output.
RESET
C5[8]
External Reset input: A LOW on this pin resets the device,
causing I/O ports and peripherals to take on their default
states, and processor execution to begin at address 0. TTL
with hysteresis, 5 V tolerant.
XTAL1
142[9]
141[9]
C3[9]
B3[9]
I
Input to the oscillator circuit and internal clock generator
circuits.
XTAL2
VSS
O
I
Output from the oscillator amplifier.
3, 9, 26, 38, C2, E4, J2,
54, 67, 79, N2, N7, L10,
93, 103, 107, K12, F13,
Ground: 0 V reference.
111, 128
D11, B13,
B11, D7
VSSA
139
C4
I
I
I
Analog ground: 0 V reference. This should nominally be the
same voltage as VSS, but should be isolated to minimize noise
and error.
VSSA(PLL)
138
B4
PLL analog ground: 0 V reference. This should nominally be
the same voltage as VSS, but should be isolated to minimize
noise and error.
VDD(1V8)
37, 110
N1, A12
1.8 V core power supply: This is the power supply voltage
for internal circuitry.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
13 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Symbol
Pin description …continued
Pin (LQFP)
Pin
(TFBGA)[1]
Type
Description
VDDA(1V8)
143
A2
I
Analog 1.8 V core power supply: This is the power supply
voltage for internal circuitry. This should be nominally the
same voltage as VDD(1V8) but should be isolated to minimize
noise and error.
VDD(3V3)
2, 31, 39, 51, B1, K3, M3,
57, 77, 94, M6, N8, K10,
104, 112, 119 F12, C13,
A11, B9
I
I
3.3 V pad power supply: This is the power supply voltage for
the I/O ports.
VDDA(3V3)
14
F3
Analog 3.3 V pad power supply: This should be nominally
the same voltage as VDD(3V3) but should be isolated to
minimize noise and error.
[1] LPC2294 only.
[2] 5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control.
[3] SSP interface available on LPC2292/2294/01 only.
[4] 5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control. If configured for an input
function, this pad utilizes built-in glitch filter that blocks pulses shorter than 3 ns.
[5] Open-drain 5 V tolerant digital I/O I2C-bus 400 kHz specification compatible pad. It requires external pull-up to provide an output
functionality. Open-drain configuration applies to all output functions on this pin.
[6] 5 V tolerant pad providing digital I/O (with TTL levels and hysteresis and 10 ns slew rate control) and analog input function. If configured
for a digital input function, this pad utilizes built-in glitch filter that blocks pulses shorter than 3 ns. When configured as an ADC input,
digital section of the pad is disabled.
[7] 5 V tolerant pad with built-in pull-up resistor providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control.
The pull-up resistor’s value ranges from 60 kΩ to 300 kΩ.
[8] 5 V tolerant pad providing digital input (with TTL levels and hysteresis) function only.
[9] Pad provides special analog functionality.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
14 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6. Functional description
6.1 Architectural overview
The ARM7TDMI-S is a general purpose 32-bit microprocessor, which offers high
performance and very low power consumption. The ARM architecture is based on RISC
principles, and the instruction set and related decode mechanism are much simpler than
those of microprogrammed CISC. This simplicity results in a high instruction throughput
and impressive real-time interrupt response from a small and cost-effective processor
core.
Pipeline techniques are employed so that all parts of the processing and memory systems
can operate continuously. Typically, while one instruction is being executed, its successor
is being decoded, and a third instruction is being fetched from memory.
The ARM7TDMI-S processor also employs a unique architectural strategy known as
Thumb, which makes it ideally suited to high-volume applications with memory
restrictions, or applications where code density is an issue.
The key idea behind Thumb is that of a super-reduced instruction set. Essentially, the
ARM7TDMI-S processor has two instruction sets:
• The standard 32-bit ARM set
• A 16-bit Thumb set
The Thumb set’s 16-bit instruction length allows it to approach twice the density of
standard ARM code while retaining most of the ARM’s performance advantage over a
traditional 16-bit processor using 16-bit registers. This is possible because Thumb code
operates on the same 32-bit register set as ARM code.
Thumb code is able to provide up to 65 % of the code size of ARM, and 160 % of the
performance of an equivalent ARM processor connected to a 16-bit memory system.
6.2 On-chip flash program memory
The LPC2292/LPC2294 incorporate a 256 kB flash memory system respectively. This
memory may be used for both code and data storage. Programming of the flash memory
may be accomplished in several ways. It may be programmed In System via the serial
port. The application program may also erase and/or program the flash while the
application is running, allowing a great degree of flexibility for data storage field firmware
upgrades, etc. When the on-chip bootloader is used, 248 kB of flash memory is available
for user code.
The LPC2292/LPC2294 flash memory provides a minimum of 100000 erase/write cycles
and 20 years of data retention.
On-chip bootloader (as of revision 1.64) provides Code Read Protection (CRP) for the
LPC2292/LPC2294 on-chip flash memory. When the CRP is enabled, the JTAG debug
port, external memory boot and ISP commands accessing either the on-chip RAM or flash
memory are disabled. However, the ISP flash erase command can be executed at any
time (no matter whether the CRP is on or off). Removal of CRP is achieved by erasure of
full on-chip user flash. With the CRP off, full access to the chip via the JTAG and/or ISP is
restored.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
15 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.3 On-chip SRAM
On-chip SRAM may be used for code and/or data storage. The SRAM may be accessed
as 8-bit, 16-bit, and 32-bit. The LPC2292/LPC2294 provide 16 kB of SRAM.
6.4 Memory map
The LPC2292/LPC2294 memory maps incorporate several distinct regions, as shown in
Figure 4.
In addition, the CPU interrupt vectors may be re-mapped to allow them to reside in either
flash memory (the default) or on-chip static RAM. This is described in Section 6.19
“System control”.
4.0 GB
3.75 GB
3.5 GB
0xFFFF FFFF
AHB PERIPHERALS
APB PERIPHERALS
0xF000 0000
0xEFFF FFFF
0xE000 0000
0xDFFF FFFF
0xC000 0000
3.0 GB
RESERVED ADDRESS SPACE
0x8000 0000
0x7FFF FFFF
2.0 GB
BOOT BLOCK (RE-MAPPED FROM
ON-CHIP FLASH MEMORY)
0x7FFF E000
0x7FFF DFFF
RESERVED ADDRESS SPACE
16 kB ON-CHIP STATIC RAM
0x4000 4000
0x4000 3FFF
0x4000 0000
0x3FFF FFFF
1.0 GB
RESERVED ADDRESS SPACE
0x0004 0000
0x0003 FFFF
256 kB ON-CHIP FLASH MEMORY
0x0000 0000
0.0 GB
002aaa754
Fig 4. LPC2292/LPC2294 memory map
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
16 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.5 Interrupt controller
The VIC accepts all of the interrupt request inputs and categorizes them as Fast Interrupt
Request (FIQ), vectored Interrupt Request (IRQ), and non-vectored IRQ as defined by
programmable settings. The programmable assignment scheme means that priorities of
interrupts from the various peripherals can be dynamically assigned and adjusted.
FIQ has the highest priority. If more than one request is assigned to FIQ, the VIC
combines the requests to produce the FIQ signal to the ARM processor. The fastest
possible FIQ latency is achieved when only one request is classified as FIQ, because then
the FIQ service routine can simply start dealing with that device. But if more than one
request is assigned to the FIQ class, the FIQ service routine can read a word from the VIC
that identifies which FIQ source(s) is (are) requesting an interrupt.
Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned
to this category. Any of the interrupt requests can be assigned to any of the 16 vectored
IRQ slots, among which slot 0 has the highest priority and slot 15 has the lowest.
Non-vectored IRQs have the lowest priority.
The VIC combines the requests from all the vectored and non-vectored IRQs to produce
the IRQ signal to the ARM processor. The IRQ service routine can start by reading a
register from the VIC and jumping there. If any of the vectored IRQs are requesting, the
VIC provides the address of the highest-priority requesting IRQs service routine,
otherwise it provides the address of a default routine that is shared by all the non-vectored
IRQs. The default routine can read another VIC register to see what IRQs are active.
6.5.1 Interrupt sources
Table 5 lists the interrupt sources for each peripheral function. Each peripheral device has
one interrupt line connected to the VIC, but may have several internal interrupt flags.
Individual interrupt flags may also represent more than one interrupt source.
Table 5.
Block
Interrupt sources
Flag(s)
VIC channel #
WDT
Watchdog Interrupt (WDINT)
0
1
2
3
4
-
Reserved for software interrupts only
EmbeddedICE, DbgCommRx
ARM Core
ARM Core
Timer 0
EmbeddedICE, DbgCommTx
Match 0 to 3 (MR0, MR1, MR2, MR3)
Capture 0 to 3 (CR0, CR1, CR2, CR3)
Match 0 to 3 (MR0, MR1, MR2, MR3)
Capture 0 to 3 (CR0, CR1, CR2, CR3)
RX Line Status (RLS)
Timer 1
UART0
5
6
Transmit Holding Register Empty (THRE)
RX Data Available (RDA)
Character Time-out Indicator (CTI)
Auto-baud time-out (ABTO)[1]
End of auto-baud (ABEO)[1]
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
17 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 5.
Interrupt sources …continued
Block
Flag(s)
VIC channel #
UART1
RX Line Status (RLS)
7
Transmit Holding Register empty (THRE)
RX Data Available (RDA)
Character Time-out Indicator (CTI)
Modem Status Interrupt (MSI)
Auto-baud time-out (ABTO)[1]
End of auto-baud (ABEO)[1]
Match 0 to 6 (MR0, MR1, MR2, MR3, MR4, MR5, MR6)
SI (state change)
PWM0
I2C
8
9
SPI0
SPIF, MODF
10
SPI1 and SSP[1] SPIF, MODF and TXRIS, RXRIS, RTRIS, RORRIS
11
PLL
PLL Lock (PLOCK)
12
RTC
RTCCIF (Counter Increment), RTCALF (Alarm)
13
System Control External Interrupt 0 (EINT0)
External Interrupt 1 (EINT1)
14
15
External Interrupt 2 (EINT2)
16
External Interrupt 3 (EINT3)
17
ADC
CAN
ADC
18
1 ORed CAN Acceptance Filter
CAN1/2 Tx
19
20, 21
22, 23
24, 25
26, 27
28,29
CAN2/3 Tx (LPC2294 only)
reserved
CAN1/2 Rx
CAN3/4 Rx (LPC2294 only)
[1] SSP interface and UART0/1 auto-baud control are available on LPC2292/2294/01 only.
6.6 Pin connect block
The pin connect block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on chip peripherals. Peripherals should be connected to the appropriate pins
prior to being activated, and prior to any related interrupt(s) being enabled. Activity of any
enabled peripheral function that is not mapped to a related pin should be considered
undefined.
6.7 External memory controller
The external Static Memory Controller is a module which provides an interface between
the system bus and external (off-chip) memory devices. It provides support for up to four
independently configurable memory banks (16 MB each with byte lane enable control)
simultaneously. Each memory bank is capable of supporting SRAM, ROM, flash EPROM,
burst ROM memory, or some external I/O devices.
Each memory bank may be 8-bit, 16-bit, or 32-bit wide.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
18 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.8 General purpose parallel I/O (GPIO) and Fast I/O
Device pins that are not connected to a specific peripheral function are controlled by the
parallel I/O registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back, as well as the current state of the port pins.
6.8.1 Features
• Bit-level set and clear registers allow a single instruction set or clear of any number of
bits in one port.
• Direction control of individual bits.
• Separate control of output set and clear.
• All I/O default to inputs after reset.
6.8.2 Features added with the Fast GPIO set of registers available on
LPC2292/LPC2294/01 only
• Fast GPIO registers are relocated to the ARM local bus for the fastest possible I/O
timing, enabling port pin toggling up to 3.5 times faster than earlier LPC2000 devices.
• Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
• All Fast GPIO registers are byte addressable.
• Entire port value can be written in one instruction.
• Ports are accessible via either the legacy group of registers (GPIOs) or the group of
registers providing accelerated port access (Fast GPIOs).
6.9 10-bit ADC
The LPC2292/LPC2294 each contain a single 10-bit successive approximation ADC with
four multiplexed channels.
6.9.1 Features
• Measurement range of 0 V to 3 V.
• Capable of performing more than 400000 10-bit samples per second.
• Burst conversion mode for single or multiple inputs.
• Optional conversion on transition on input pin or Timer Match signal.
6.9.2 ADC features available in LPC2292/LPC2294/01 only
• Every analog input has a dedicated result register to reduce interrupt overhead.
• Every analog input can generate an interrupt once the conversion is completed.
• The ADC pads are 5 V tolerant when configured for digital I/O function(s).
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
19 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.10 CAN controllers and acceptance filter
The LPC2292/LPC2294 each contain two/four CAN controllers. The CAN is a serial
communications protocol which efficiently supports distributed real-time control with a
very high level of security. Its domain of application ranges from high-speed networks to
low cost multiplex wiring.
6.10.1 Features
• Data rates up to 1 Mbit/s on each bus.
• 32-bit register and RAM access.
• Compatible with CAN specification 2.0B, ISO 11898-1.
• Global Acceptance Filter recognizes 11-bit and 29-bit RX identifiers for all CAN buses.
• Acceptance Filter can provide FullCAN-style automatic reception for selected
Standard identifiers.
6.11 UARTs
The LPC2292/LPC2294 each contain two UARTs. In addition to standard transmit and
receive data lines, the UART1 also provides a full modem control handshake interface.
6.11.1 Features
• 16 B Receive and Transmit FIFOs.
• Register locations conform to 16C550 industry standard.
• Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B
• Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• Transmission FIFO control enables implementation of software (XON/XOFF) flow
control on both UARTs.
• UART1 is equipped with standard modem interface signals. This module also
provides full support for hardware flow control (auto-CTS/RTS).
6.11.2 UART features available in LPC2292/LPC2294/01 only
Compared to previous LPC2000 microcontrollers, UARTs in LPC2292/LPC2294/01
introduce a fractional baud rate generator for both UARTs, enabling these microcontrollers
to achieve standard baud rates such as 115200 Bd with any crystal frequency above
2 MHz. In addition, auto-CTS/RTS flow-control functions are fully implemented in
hardware.
• Fractional baud rate generator enables standard baud rates such as 115200 Bd to be
achieved with any crystal frequency above 2 MHz.
• Auto-bauding.
• Auto-CTS/RTS flow-control fully implemented in hardware.
6.12 I2C-bus serial I/O controller
The I2C-bus is bidirectional, for inter-IC control using only two wires: a serial clock line
(SCL), and a serial data line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver or a transmitter with the
© NXP B.V. 2008. All rights reserved.
LPC2292_2294_7
Product data sheet
Rev. 7 — 4 December 2008
20 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I2C-bus is a multi-master bus, it can be
controlled by more than one bus master connected to it.
The I2C-bus implemented in LPC2292/LPC2294 supports bit rate up to 400 kbit/s (Fast
I2C-bus).
6.12.1 Features
• Compliant with standard I2C-bus interface.
• Easy to configure as master, slave, or master/slave.
• Programmable clocks allow versatile rate control.
• Bidirectional data transfer between masters and slaves.
• Multi-master bus (no central master).
• Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
• The I2C-bus may be used for test and diagnostic purposes.
6.13 SPI serial I/O controller
The LPC2292/LPC2294 each contain two SPIs. The SPI is a full duplex serial interface,
designed to be able to handle multiple masters and slaves connected to a given bus. Only
a single master and a single slave can communicate on the interface during a given data
transfer. During a data transfer the master always sends a byte of data to the slave, and
the slave always sends a byte of data to the master.
6.13.1 Features
• Compliant with Serial Peripheral Interface (SPI) specification.
• Synchronous, Serial, Full Duplex communication.
• Combined SPI master and slave.
• Maximum data bit rate of 1⁄8 of the input clock rate.
6.13.2 Features available in LPC2292/LPC2294/01 only
• Eight to 16 bits per frame.
• When the SPI interface is used in Master mode, the SSELn pin is not needed (can be
used for a different function).
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
21 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.14 SSP controller (LPC2292/94/01 only)
The SSP is a controller capable of operation on a SPI, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. Data transfers are in
principle full duplex, with frames of four to 16 bits of data flowing from the master to the
slave and from the slave to the master.
While the SSP and SPI1 peripherals share the same physical pins, it is not possible to
have both of these two peripherals active at the same time. Application can switch on the
fly from SPI1 to SSP and back.
6.14.1 Features
• Compatible with Motorola’s SPI, Texas Instrument’s 4-wire SSI, and National
Semiconductor’s Microwire buses.
• Synchronous serial communication.
• Master or slave operation.
• 8-frame FIFOs for both transmit and receive.
• Four to 16 bits per frame.
6.15 General purpose timers
The Timer/Counter is designed to count cycles of the peripheral clock (PCLK) or an
externally supplied clock and optionally generate interrupts or perform other actions at
specified timer values, based on four match registers. It also includes four capture inputs
to trap the timer value when an input signal transitions, optionally generating an interrupt.
Multiple pins can be selected to perform a single capture or match function, providing an
application with ‘or’ and ‘and’, as well as ‘broadcast’ functions among them.
6.15.1 Features
• A 32-bit Timer/Counter with a programmable 32-bit Prescaler.
• Timer or external event counter operation
• Four 32-bit capture channels per timer that can take a snapshot of the timer value
when an input signal transitions. A capture event may also optionally generate an
interrupt.
• Four 32-bit match registers that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Four external outputs per timer corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
22 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.15.2 Features available in LPC2292/LPC2294/01 only
The LPC2292/LPC2294/01 can count external events on one of the capture inputs if the
external pulse lasts at least one half of the period of the PCLK. In this configuration,
unused capture lines can be selected as regular timer capture inputs, or used as external
interrupts.
• Timer can count cycles of either the peripheral clock (PCLK) or an externally supplied
clock.
• When counting cycles of an externally supplied clock, only one of the timer’s capture
inputs can be selected as the timer’s clock. The rate of such a clock is limited to
PCLK / 4. Duration of HIGH/LOW levels on the selected CAP input cannot be shorter
than 1 / (2PCLK).
6.16 Watchdog timer
The purpose of the watchdog is to reset the microcontroller within a reasonable amount of
time if it enters an erroneous state. When enabled, the watchdog will generate a system
reset if the user program fails to ‘feed’ (or reload) the watchdog within a predetermined
amount of time.
6.16.1 Features
• Internally resets chip if not periodically reloaded.
• Debug mode.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
• Incorrect/incomplete feed sequence causes reset/interrupt if enabled.
• Flag to indicate watchdog reset.
• Programmable 32-bit timer with internal prescaler.
• Selectable time period from (Tcy(PCLK) × 256 × 4) to (Tcy(PCLK) × 232 × 4) in multiples of
T
cy(PCLK) × 4.
6.17 Real-time clock
The Real-Time Clock (RTC) is designed to provide a set of counters to measure time
when normal or idle operating mode is selected. The RTC has been designed to use little
power, making it suitable for battery powered systems where the CPU is not running
continuously (Idle mode).
6.17.1 Features
• Measures the passage of time to maintain a calendar and clock.
• Ultra-low power design to support battery powered systems.
• Provides Seconds, Minutes, Hours, Day of Month, Month, Year, Day of Week, and Day
of Year.
• Programmable Reference Clock Divider allows adjustment of the RTC to match
various crystal frequencies.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
23 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.18 Pulse width modulator
The PWM is based on the standard Timer block and inherits all of its features, although
only the PWM function is pinned out on the LPC2292/LPC2294. The Timer is designed to
count cycles of the peripheral clock (PCLK) and optionally generate interrupts or perform
other actions when specified timer values occur, based on seven match registers. The
PWM function is also based on match register events.
The ability to separately control rising and falling edge locations allows the PWM to be
used for more applications. For instance, multi-phase motor control typically requires three
non-overlapping PWM outputs with individual control of all three pulse widths and
positions.
Two match registers can be used to provide a single edge controlled PWM output. One
match register (MR0) controls the PWM cycle rate, by resetting the count upon match.
The other match register controls the PWM edge position. Additional single edge
controlled PWM outputs require only one match register each, since the repetition rate is
the same for all PWM outputs. Multiple single edge controlled PWM outputs will all have a
rising edge at the beginning of each PWM cycle, when an MR0 match occurs.
Three match registers can be used to provide a PWM output with both edges controlled.
Again, the MR0 match register controls the PWM cycle rate. The other match registers
control the two PWM edge positions. Additional double edge controlled PWM outputs
require only two match registers each, since the repetition rate is the same for all PWM
outputs.
With double edge controlled PWM outputs, specific match registers control the rising and
falling edge of the output. This allows both positive going PWM pulses (when the rising
edge occurs prior to the falling edge), and negative going PWM pulses (when the falling
edge occurs prior to the rising edge).
6.18.1 Features
• Seven match registers allow up to six single edge controlled or three double edge
controlled PWM outputs, or a mix of both types.
• The match registers also allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Supports single edge controlled and/or double edge controlled PWM outputs. Single
edge controlled PWM outputs all go HIGH at the beginning of each cycle unless the
output is a constant LOW. Double edge controlled PWM outputs can have either edge
occur at any position within a cycle. This allows for both positive going and negative
going pulses.
• Pulse period and width can be any number of timer counts. This allows complete
flexibility in the trade-off between resolution and repetition rate. All PWM outputs will
occur at the same repetition rate.
• Double edge controlled PWM outputs can be programmed to be either positive going
or negative going pulses.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
24 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
• Match register updates are synchronized with pulse outputs to prevent generation of
erroneous pulses. Software must ‘release’ new match values before they can become
effective.
• May be used as a standard timer if the PWM mode is not enabled.
• A 32-bit Timer/Counter with a programmable 32-bit prescaler.
6.19 System control
6.19.1 Crystal oscillator
The oscillator supports crystals in the range of 1 MHz to 25 MHz. The oscillator output
frequency is called fosc and the ARM processor clock frequency is referred to as CCLK for
purposes of rate equations, etc. fosc and CCLK are the same value unless the PLL is
running and connected. Refer to Section 6.19.2 “PLL” for additional information.
6.19.2 PLL
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up into the range of 10 MHz to 60 MHz with a Current Controlled
Oscillator (CCO). The multiplier can be an integer value from 1 to 32 (in practice, the
multiplier value cannot be higher than 6 on this family of microcontrollers due to the upper
frequency limit of the CPU). The CCO operates in the range of 156 MHz to 320 MHz, so
there is an additional divider in the loop to keep the CCO within its frequency range while
the PLL is providing the desired output frequency. The output divider may be set to divide
by 2, 4, 8, or 16 to produce the output clock. Since the minimum output divider value is 2,
it is insured that the PLL output has a 50 % duty cycle.The PLL is turned off and bypassed
following a chip reset and may be enabled by software. The program must configure and
activate the PLL, wait for the PLL to Lock, then connect to the PLL as a clock source. The
PLL settling time is 100 µs.
6.19.3 Reset and wake-up timer
Reset has two sources on the LPC2292/LPC2294: the RESET pin and watchdog reset.
The RESET pin is a Schmitt trigger input pin with an additional glitch filter. Assertion of
chip reset by any source starts the Wake-up Timer (see Wake-up Timer description
below), causing the internal chip reset to remain asserted until the external reset is
de-asserted, the oscillator is running, a fixed number of clocks have passed, and the
on-chip flash controller has completed its initialization.
When the internal reset is removed, the processor begins executing at address 0, which is
the reset vector. At that point, all of the processor and peripheral registers have been
initialized to predetermined values.
The Wake-up Timer ensures that the oscillator and other analog functions required for
chip operation are fully functional before the processor is allowed to execute instructions.
This is important at power-on, all types of reset, and whenever any of the aforementioned
functions are turned off for any reason. Since the oscillator and other functions are turned
off during Power-down mode, any wake-up of the processor from Power-down mode
makes use of the Wake-up Timer.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
25 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
The Wake-up Timer monitors the crystal oscillator as the means of checking whether it is
safe to begin code execution. When power is applied to the chip, or some event caused
the chip to exit Power-down mode, some time is required for the oscillator to produce a
signal of sufficient amplitude to drive the clock logic. The amount of time depends on
many factors, including the rate of VDD ramp (in the case of power-on), the type of crystal
and its electrical characteristics (if a quartz crystal is used), as well as any other external
circuitry (e.g. capacitors), and the characteristics of the oscillator itself under the existing
ambient conditions.
6.19.4 Code security (Code Read Protection - CRP)
This feature of the LPC2292/LPC2294/01 allows the user to enable different levels of
security in the system so that access to the on-chip flash and use of the JTAG and ISP
can be restricted. When needed, CRP is invoked by programming a specific pattern into a
dedicated flash location. IAP commands are not affected by the CRP.
There are three levels of the Code Read Protection.
CRP1 disables access to chip via the JTAG and allows partial flash update (excluding
flash sector 0) using a limited set of the ISP commands. This mode is useful when CRP is
required and flash field updates are needed but all sectors can not be erased.
CRP2 disables access to chip via the JTAG and only allows full flash erase and update
using a reduced set of the ISP commands.
Running an application with level CRP3 selected fully disables any access to chip via the
JTAG pins and the ISP. This mode effectively disables ISP override using P0[14] pin, too. It
is up to the user’s application to provide (if needed) flash update mechanism using IAP
calls or call reinvoke ISP command to enable flash update via UART0.
CAUTION
If level three Code Read Protection (CRP3) is selected, no future factory testing can be
performed on the device.
Remark: Devices without a /00 or /01 in the name have only a security level equivalent to
CRP2 available.
6.19.5 External interrupt inputs
The LPC2292/LPC2294 include up to nine edge or level sensitive External Interrupt Inputs
as selectable pin functions. When the pins are combined, external events can be
processed as four independent interrupt signals. The External Interrupt Inputs can
optionally be used to wake up the processor from Power-down mode.
6.19.6 Memory mapping control
The Memory Mapping Control alters the mapping of the interrupt vectors that appear
beginning at address 0x0000 0000. Vectors may be mapped to the bottom of the on-chip
flash memory, or to the on-chip static RAM. This allows code running in different memory
spaces to have control of the interrupts.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
26 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.19.7 Power control
The LPC2292/LPC2294 support two reduced power modes: Idle mode and Power-down
mode. In Idle mode, execution of instructions is suspended until either a reset or interrupt
occurs. Peripheral functions continue operation during Idle mode and may generate
interrupts to cause the processor to resume execution. Idle mode eliminates power used
by the processor itself, memory systems and related controllers, and internal buses.
In Power-down mode, the oscillator is shut down, and the chip receives no internal clocks.
The processor state and registers, peripheral registers, and internal SRAM values are
preserved throughout Power-down mode, and the logic levels of chip output pins remain
static. The Power-down mode can be terminated and normal operation resumed by either
a reset or certain specific interrupts that are able to function without clocks. Since all
dynamic operation of the chip is suspended, Power-down mode reduces chip power
consumption to nearly zero.
A Power Control for Peripherals feature allows individual peripherals to be turned off if
they are not needed in the application, resulting in additional power savings.
6.19.8 APB bus
The APB divider determines the relationship between the processor clock (CCLK) and the
clock used by peripheral devices (PCLK). The APB divider serves two purposes. The first
is to provide peripherals with the desired PCLK via APB bus so that they can operate at
the speed chosen for the ARM processor. In order to achieve this, the APB bus may be
slowed down to 1⁄2 to 1⁄4 of the processor clock rate. Because the APB bus must work
properly at power-up (and its timing cannot be altered if it does not work since the APB
divider control registers reside on the APB bus), the default condition at reset is for the
APB bus to run at 1⁄4 of the processor clock rate. The second purpose of the APB divider
is to allow power savings when an application does not require any peripherals to run at
the full processor rate. Because the APB divider is connected to the PLL output, the PLL
remains active (if it was running) during Idle mode.
6.20 Emulation and debugging
The LPC2292/LPC2294 support emulation and debugging via a JTAG serial port. A trace
port allows tracing program execution. Debugging and trace functions are multiplexed only
with GPIOs on Port 1. This means that all communication, timer and interface peripherals
residing on Port 0 are available during the development and debugging phase as they are
when the application is run in the embedded system itself.
6.20.1 EmbeddedICE
Standard ARM EmbeddedICE logic provides on-chip debug support. The debugging of
the target system requires a host computer running the debugger software and an
EmbeddedICE protocol converter. EmbeddedICE protocol converter converts the remote
debug protocol commands to the JTAG data needed to access the ARM core.
The ARM core has a Debug Communication Channel function built-in. The debug
communication channel allows a program running on the target to communicate with the
host debugger or another separate host without stopping the program flow or even
entering the debug state. The debug communication channel is accessed as a
co-processor 14 by the program running on the ARM7TDMI-S core. The debug
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
27 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
communication channel allows the JTAG port to be used for sending and receiving data
without affecting the normal program flow. The debug communication channel data and
control registers are mapped in to addresses in the EmbeddedICE logic.
The JTAG clock (TCK) must be slower than 1⁄6 of the CPU clock (CCLK) for the JTAG
interface to operate.
6.20.2 Embedded trace
Since the LPC2292/LPC2294 have significant amounts of on-chip memory, it is not
possible to determine how the processor core is operating simply by observing the
external pins. The Embedded Trace Macrocell (ETM) provides real-time trace capability
for deeply embedded processor cores. It outputs information about processor execution to
the trace port.
The ETM is connected directly to the ARM core and not to the main AMBA system bus. It
compresses the trace information and exports it through a narrow trace port. An external
trace port analyzer must capture the trace information under software debugger control.
Instruction trace (or PC trace) shows the flow of execution of the processor and provides a
list of all the instructions that were executed. Instruction trace is significantly compressed
by only broadcasting branch addresses as well as a set of status signals that indicate the
pipeline status on a cycle by cycle basis. Trace information generation can be controlled
by selecting the trigger resource. Trigger resources include address comparators,
counters and sequencers. Since trace information is compressed the software debugger
requires a static image of the code being executed. Self-modifying code cannot be traced
because of this restriction.
6.20.3 RealMonitor
RealMonitor is a configurable software module, developed by ARM Inc., which enables
real-time debug. It is a lightweight debug monitor that runs in the background while users
debug their foreground application. It communicates with the host using the Debug
Communications Channel (DCC), which is present in the EmbeddedICE logic. The
LPC2292/LPC2294 contain a specific configuration of RealMonitor software programmed
into the on-chip flash memory.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
28 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
7. Limiting values
Table 6.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
VDD(1V8)
VDD(3V3)
VDDA(3V3)
VIA
Parameter
Conditions
Min
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
-
Max
Unit
V
[2]
[3]
supply voltage (1.8 V)
supply voltage (3.3 V)
analog supply voltage (3.3 V)
analog input voltage
input voltage
+2.5
+3.6
V
+4.6
V
+5.1
V
[4][5]
[4][6]
[7][8]
[8][9]
VI
5 V tolerant I/O pins
other I/O pins
+6.0
V
VDD(3V3) + 0.5
100
V
IDD
supply current
mA
mA
°C
°C
W
ISS
ground current
-
100
Tj
junction temperature
storage temperature
-
150
[10]
[11]
Tstg
Ptot(pack)
−65
-
+150
1.5
total power dissipation (per
package)
based on package heat
transfer, not device
power consumption
Vesd
electrostatic discharge voltage human body model
all pins
−2000
+2000
V
[1] The following applies to Table 6:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2] Internal rail.
[3] External rail.
[4] Including voltage on outputs in 3-state mode.
[5] Only valid when the VDD(3V3) supply voltage is present.
[6] Not to exceed 4.6 V.
[7] Per supply pin.
[8] The peak current is limited to 25 times the corresponding maximum current.
[9] Per ground pin.
[10] Dependent on package type.
[11] Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
29 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
8. Static characteristics
Table 7.
Static characteristics
Tamb = −40 °C to +125 °C, unless otherwise specified.
Symbol Parameter
Conditions
Min
1.65
3.0
Typ[1]
1.8
Max
1.95
3.6
Unit
V
[2]
[3]
VDD(1V8) supply voltage (1.8 V)
VDD(3V3) supply voltage (3.3 V)
3.3
V
VDDA(3V3) analog supply voltage
(3.3 V)
2.5
3.3
3.6
V
Standard port pins, RESET, RTCK
IIL
LOW-level input current
HIGH-level input current
OFF-state output current
VI = 0 V; no pull-up
-
-
-
-
-
-
3
3
3
µA
µA
µA
IIH
IOZ
VI = VDD(3V3); no pull-down
VO = 0 V, VO = VDD(3V3)
;
no pull-up/down
Ilatch
VI
I/O latch-up current
input voltage
−(0.5VDD(3V3)) < VI <
(1.5VDD(3V3)); Tj < 125 °C
100
0
-
-
-
mA
V
[4][5]
[6]
5.5
VO
output voltage
output active
0
-
-
-
-
VDD(3V3)
V
VIH
VIL
HIGH-level input voltage
LOW-level input voltage
hysteresis voltage
2.0
-
-
V
0.8
V
Vhys
VOH
VOL
IOH
IOL
0.4
-
V
[7]
[7]
[7]
[7]
[8]
HIGH-level output voltage
LOW-level output voltage
HIGH-level output current
LOW-level output current
IOH = −4 mA
IOL = 4 mA
V
-
DD(3V3) − 0.4 -
-
V
-
-
-
-
0.4
-
V
VOH = VDD(3V3) − 0.4 V
VOL = 0.4 V
−4
4
-
mA
mA
mA
-
IOHS
HIGH-level short-circuit
output current
VOH = 0 V
−45
[8]
IOLS
LOW-level short-circuit
output current
VOL = VDD(3V3)
-
-
50
mA
[9]
[10]
[9]
Ipd
Ipu
pull-down current
pull-up current
VI = 5 V
10
−15
0
50
−50
0
150
−85
0
µA
µA
µA
VI = 0 V
VDD(3V3) < VI < 5 V
Power consumption LPC2292, LPC2292/00, LPC2294, LPC2294/00
IDD(act)
active mode supply current VDD(1V8) = 1.8 V;
CCLK = 60 MHz;
-
50
-
mA
T
amb = 25 °C; code
while(1){}
executed from flash; all
peripherals enabled via
PCONP[11] register but not
configured to run
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
30 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 7.
Static characteristics …continued
Tamb = −40 °C to +125 °C, unless otherwise specified.
Symbol Parameter
IDD(pd) Power-down mode supply
current
Conditions
Min
Typ[1]
Max
Unit
VDD(1V8) = 1.8 V;
-
10
-
µA
T
amb = 25 °C
VDD(1V8) = 1.8 V;
amb = 85 °C
VDD(1V8) = 1.8 V;
amb = 125 °C
Power consumption LPC2292/01 and LPC2294/01
-
-
110
300
500
µA
µA
T
1000
T
IDD(act)
active mode supply current VDD(1V8) = 1.8 V;
CCLK = 60 MHz;
-
45
-
mA
T
amb = 25 °C; code
while(1){}
executed from flash; all
peripherals enabled via
PCONP[11] register but not
configured to run
IDD(idle)
Idle mode supply current
VDD(1V8) = 1.8 V;
CCLK = 60 MHz;
-
11.5
-
mA
T
amb = 25 °C;
executed from flash; all
peripherals enabled via
PCONP[11] register but not
configured to run
IDD(pd)
Power-down mode supply
current
VDD(1V8) = 1.8 V;
-
-
-
10
-
-
µA
µA
µA
T
amb = 25 °C
VDD(1V8) = 1.8 V;
amb = 85 °C
VDD(1V8) = 1.8 V;
amb = 125 °C
180
430
T
-
T
I2C-bus pins
VIH
VIL
Vhys
VOL
ILI
HIGH-level input voltage
0.7VDD(3V3)
-
-
V
LOW-level input voltage
hysteresis voltage
-
-
-
-
-
-
0.3VDD(3V3)
V
0.5VDD(3V3)
-
V
[7]
LOW-level output voltage
input leakage current
IOLS = 3 mA
VI = VDD(3V3)
VI = 5 V
-
0.4
4
V
[12]
2
µA
µA
10
22
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
31 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 7.
Static characteristics …continued
Tamb = −40 °C to +125 °C, unless otherwise specified.
Symbol Parameter
Oscillator pins
Conditions
Min
Typ[1]
Max
Unit
Vi(XTAL1)
input voltage on pin XTAL1
0
0
-
-
1.8
1.8
V
V
Vo(XTAL2) output voltage on pin
XTAL2
[1] Typical ratings are not guaranteed. The values listed are at room temperature (+25 °C), nominal supply voltages.
[2] Internal rail.
[3] External rail.
[4] Including voltage on outputs in 3-state mode.
[5] VDD(3V3) supply voltages must be present.
[6] 3-state outputs go into 3-state mode when VDD(3V3) is grounded.
[7] Accounts for 100 mV voltage drop in all supply lines.
[8] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[9] Minimum condition for VI = 4.5 V, maximum condition for VI = 5.5 V.
[10] Applies to P1[25:16].
[11] See the LPC2119/2129/2194/2292/2294 User Manual.
[12] To VSS
.
Table 8.
ADC static characteristics
VDDA = 2.5 V to 3.6 V; Tamb = −40 °C to +125 °C unless otherwise specified. ADC frequency 4.5 MHz.
Symbol
VIA
Parameter
Conditions
Min
Typ
Max
Unit
analog input voltage
0
-
-
-
VDDA
1
V
Cia
analog input
capacitance
pF
ED
differential linearity
error
-
-
±1
LSB
[1][2][3]
[1][4]
[1][5]
[1][6]
[1][7]
EL(adj)
EO
integral non-linearity
offset error
-
-
-
-
-
-
-
-
±2
LSB
LSB
%
±3
EG
gain error
±0.5
±4
ET
absolute error
LSB
[1] Conditions: VSSA = 0 V, VDDA = 3.3 V.
[2] The ADC is monotonic, there are no missing codes.
[3] The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 5.
[4] The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See Figure 5.
[5] The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See Figure 5.
[6] The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
error, and the straight line which fits the ideal transfer curve. See Figure 5.
[7] The absolute voltage error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the
non-calibrated ADC and the ideal transfer curve. See Figure 5.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
32 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
gain
error
offset
error
E
E
O
G
1023
1022
1021
1020
1019
1018
(2)
7
code
out
(1)
6
5
4
3
2
1
0
(5)
(4)
(3)
1 LSB
(ideal)
1018 1019 1020 1021 1022 1023 1024
1
2
3
4
5
6
7
V
IA
(LSB
)
ideal
V
− V
SSA
DDA
1 LSB =
offset
error
1024
002aaa668
E
O
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 5. ADC characteristics
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
33 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
8.1 Power consumption measurements for LPC2292/01 and LPC2294/01
The power consumption measurements represent typical values for the given conditions.
The peripherals were enabled through the PCONP register, but for these measurements,
the peripherals were not configured to run. Peripherals were disabled through the PCONP
register. For a description of the PCONP register bits, refer to the
LPC2119/2129/2194/2292/2294 User Manual.
002aad102
50
I
DD(act)
(mA)
40
30
20
10
0
all peripherals enabled
all peripherals disabled
12
20
28
36
44
52
60
frequency (MHz)
Test conditions: Active mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; core voltage 1.8 V.
Fig 6. Typical LPC2292/01 IDD(act) measured at different frequencies
002aad103
50
60 MHz
I
DD(act)
(mA)
48 MHz
40
30
20
10
0
12 MHz
1.65
1.80
1.95
voltage (V)
Test conditions: Active mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; all peripherals enabled but not active.
Fig 7. Typical LPC2292/01 IDD(act) measured at different core voltages
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
34 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aad104
45
60 MHz
I
DD(act)
(mA)
48 MHz
35
25
15
5
12 MHz
-40
-15
10
35
60
85
temperature (°C)
Test conditions: Active mode entered executing code on-chip flash; PCLK = CCLK⁄4;
core voltage 1.8 V; all peripherals disabled.
Fig 8. Typical LPC2292/01 IDD(act) measured at different temperatures
002aad105
10.0
I
DD(idle)
(mA)
8.0
6.0
4.0
2.0
0.0
all peripherals enabled
all peripherals disabled
12
20
28
36
44
52
60
frequency (MHz)
Test conditions: Idle mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; core voltage 1.8 V.
Fig 9. Typical LPC2292/01 IDD(idle) measured at different frequencies
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
35 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aad106
10.0
I
DD(idle)
(mA)
60 MHz
48 MHz
8.0
6.0
4.0
2.0
12 MHz
1.65
1.80
1.95
voltage (V)
Test conditions: Idle mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; all peripherals enabled but not active.
Fig 10. Typical LPC2292/01 IDD(idle) measured at different core voltages
002aad107
6.0
I
DD(idle)
(mA)
5.0
4.0
3.0
2.0
1.0
60 MHz
48 MHz
12 MHz
-40
-15
10
35
60
85
temperature (°C)
Test conditions: Idle mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Core voltage 1.8 V; all peripherals disabled.
Fig 11. Typical LPC2292/01 IDD(idle) measured at different temperatures
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
36 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aad108
200
I
DD(pd)
(µA)
1.95 V
1.8 V
160
120
80
1.65 V
40
0
-40
-15
10
35
60
85
temperature (°C)
Test conditions: Power-down mode entered executing code from on-chip flash.
Fig 12. Typical LPC2292/01 core power-down current IDD(pd) measured at different temperatures
002aad109
50.0
I
DD(act)
(mA)
all peripherals enabled
all peripherals disabled
40.0
30.0
20.0
10.0
0.0
12
20
28
36
44
52
60
frequency (MHz)
Test conditions: Active mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; core voltage 1.8 V.
Fig 13. Typical LPC2294/01 IDD(act) measured at different frequencies
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
37 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aad110
55.0
I
DD(act)
(mA)
60 MHz
48 MHz
45.0
35.0
25.0
15.0
5.0
12 MHz
1.65
1.80
1.95
voltage (V)
Test conditions: Active mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; all peripherals enabled but not active.
Fig 14. Typical LPC2294/01 IDD(act) measured at different core voltages
002aad111
45.0
60 MHz
I
DD(act)
(mA)
48 MHz
35.0
25.0
15.0
5.0
12 MHz
-40
-25
-10
5
20
35
50
65
80
95
110
temperature (°C)
125
Test conditions: Active mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
core voltage 1.8 V; all peripherals disabled.
Fig 15. Typical LPC2294/01 IDD(act) measured at different temperatures
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
38 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aad112
15.0
I
DD(idle)
(mA)
10.0
5.0
all peripherals enabled
all peripherals disabled
0.0
12
20
28
36
44
52
60
frequency (MHz)
Test conditions: Idle mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; core voltage 1.8 V.
Fig 16. Typical LPC2294/01 IDD(idle) measured at different frequencies
002aad113
15.0
I
DD(idle)
(mA)
60 MHz
48 MHz
10.0
5.0
12 MHz
0.0
1.65
1.80
1.95
voltage (V)
Test conditions: Idle mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; all peripherals enabled but not active.
Fig 17. Typical LPC2294/01 IDD(idle) measured at different core voltages
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
39 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aad114
6.50
I
DD(idle)
(mA)
60 MHz
5.50
48 MHz
4.50
3.50
2.50
1.50
0.50
12 MHz
-40
-25
-10
5
20
35
50
65
80
95
110
125
temperature (°C)
Test conditions: Idle mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
core voltage 1.8 V; all peripherals disabled.
Fig 18. Typical LPC2294/01 IDD(idle) measured at different temperatures
002aad115
500
I
DD(pd)
(µA)
1.95 V
1.8 V
400
300
200
100
0
1.65 V
-40
-25
-10
5
20
35
50
65
80
95
110
125
temperature (°C)
Test conditions: Power-down mode entered executing code from on-chip flash.
Fig 19. Typical LPC2294/01 core power-down current IDD(pd) measured at different temperatures
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
40 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aad116
45.0
I
DD(act)
(mA)
60 MHz
48 MHz
35.0
25.0
15.0
5.0
12 MHz
1.65
1.80
1.95
voltage (V)
Test conditions: Active mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; all peripherals disabled.
Fig 20. Typical LPC2292/01 and LPC2294/01 IDD(act) measured at different core voltages
002aad117
10.0
I
DD(idle)
(mA)
60 MHz
48 MHz
5.0
12 MHz
0.0
1.65
1.80
1.95
voltage (V)
Test conditions: Idle mode entered executing code from on-chip flash; PCLK = CCLK⁄4;
Tamb = 25 °C; all peripherals disabled.
Fig 21. Typical LPC2292/01 and LPC2294/01 IDD(idle) measured at different core voltages
Table 9.
Typical LPC2292/01 peripheral power consumption in active mode
Core voltage 1.8 V; Tamb = 25 °C; all measurements in µA; PCLK = CCLK⁄4; all peripherals enabled.
Peripheral
Timer0
CCLK = 12 MHz
CCLK = 48 MHz
CCLK = 60 MHz
43
141
150
320
351
184
180
398
421
Timer1
46
UART0
UART1
98
103
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
41 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 9.
Typical LPC2292/01 peripheral power consumption in active mode …continued
Core voltage 1.8 V; Tamb = 25 °C; all measurements in µA; PCLK = CCLK⁄4; all peripherals enabled.
Peripheral
PWM0
I2C-bus
SPI0/1
RTC
CCLK = 12 MHz
CCLK = 48 MHz
CCLK = 60 MHz
103
9
341
37
407
53
6
27
29
16
306
33
229
55
78
PCEMC
ADC
994
128
771
1205
167
914
CAN1/2
Table 10. Typical LPC2294/01 peripheral power consumption in active mode
Core voltage 1.8 V; Tamb = 25 °C; all measurements in µA; PCLK = CCLK⁄4; all peripherals enabled.
Peripheral
Timer0
Timer1
UART0
UART1
PWM0
CCLK = 12 MHz
CCLK = 48 MHz
CCLK = 60 MHz
43
46
98
103
103
9
141
150
320
351
341
37
184
180
398
421
407
53
I2C-bus
SPI0/1
6
27
29
RTC
16
306
33
230
55
78
PCEMC
ADC
994
128
769
1205
167
912
CAN1/2/3/4
9. Dynamic characteristics
Table 11. Dynamic characteristics
Tamb = −40 °C to +125 °C; VDD(1V8), VDD(3V3) over specified ranges.[1]
Symbol
External clock
fosc
Parameter
Conditions
Min
Typ
Max
Unit
oscillator frequency
supplied by an external
oscillator (signal generator)
1
1
-
-
25
25
MHz
MHz
external clock frequency
supplied by an external
crystal oscillator
external clock frequency if
on-chip PLL is used
10
10
-
-
25
25
MHz
MHz
external clock frequency if
on-chip bootloader is used
for initial code download
Tcy(clk)
tCHCX
tCLCX
clock cycle time
clock HIGH time
clock LOW time
20
-
-
-
1000
ns
ns
ns
Tcy(clk) × 0.4
cy(clk) × 0.4
-
-
T
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
42 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 11. Dynamic characteristics …continued
Tamb = −40 °C to +125 °C; VDD(1V8), VDD(3V3) over specified ranges.[1]
Symbol
tCLCH
Parameter
Conditions
Min
Typ
Max
5
Unit
ns
clock rise time
clock fall time
-
-
-
-
tCHCL
5
ns
Port pins (except P0[2] and P0[3])
tr
tf
rise time
-
-
10
10
-
-
ns
ns
fall time
I2C-bus pins (P0[2] and P0[3])
[2]
tf fall time
VIH to VIL
20 + 0.1 × Cb
-
-
ns
[1] Parameters are valid over operating temperature range unless otherwise specified.
[2] Bus capacitance Cb in pF, from 10 pF to 400 pF.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
43 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 12. External memory interface dynamic characteristics
CL = 25 pF, Tamb = 40 °C
Symbol
Parameter
Conditions
Min
Typ Max
Unit
Common to read and write cycles
tCHAV
XCLK HIGH to address valid
time
-
-
10
ns
tCHCSL
tCHCSH
XCLK HIGH to CS LOW time
-
-
-
-
10
10
ns
ns
XCLK HIGH to CS HIGH
time
tCHANV
XCLK HIGH to address
invalid time
-
-
10
ns
Read cycle parameters
tCSLAV CS LOW to address valid
[1]
[1]
−5
−5
−5
-
-
+10
+10
ns
ns
time
tOELAV
OE LOW to address valid
time
tCSLOEL
tam
CS LOW to OE LOW time
memory access time
-
-
+5
-
ns
ns
[2][3]
[2][3]
[2][4]
[5]
(Tcy(CCLK) × (2 + WST1)) +
(−20)
tam(ibr)
tam(sbr)
memory access time (initial
burst-ROM)
(Tcy(CCLK) × (2 + WST1)) +
(−20)
-
-
-
-
ns
ns
memory access time
Tcy(CCLK) + (−20)
(subsequent burst-ROM)
th(D)
data input hold time
0
-
-
-
-
ns
ns
ns
tCSHOEH
tOEHANV
CS HIGH to OE HIGH time
−5
−5
+5
+5
OE HIGH to address invalid
time
tCHOEL
tCHOEH
XCLK HIGH to OE LOW time
−5
−5
-
-
+5
+5
ns
ns
XCLK HIGH to OE HIGH
time
Write cycle parameters
[1]
tAVCSL
address valid to CS LOW
T
cy(CCLK) − 10
-
-
ns
time
tCSLDV
CS LOW to data valid time
CS LOW to WE LOW time
CS LOW to BLS LOW time
WE LOW to data valid time
CS LOW to data valid time
WE LOW to WE HIGH time
−5
−5
−5
−5
−5
-
-
-
-
-
-
+5
+5
+5
+5
+5
ns
ns
ns
ns
ns
ns
tCSLWEL
tCSLBLSL
tWELDV
tCSLDV
[2]
[2]
[2]
tWELWEH
T
T
T
cy(CCLK) × (1 + WST2) − 5
cy(CCLK) × (1 + WST2) − 5
cy(CCLK) − 5
T
cy(CCLK) × (1 +
WST2) + 5
tBLSLBLSH BLS LOW to BLS HIGH time
-
-
Tcy(CCLK)
(1 + WST2) + 5
×
ns
ns
tWEHANV
tWEHDNV
WE HIGH to address invalid
time
Tcy(CCLK) + 5
[2]
[2]
WE HIGH to data invalid time
(2 × Tcy(CCLK)) − 5
Tcy(CCLK) − 5
-
-
(2 × Tcy(CCLK)) + 5 ns
Tcy(CCLK) + 5 ns
tBLSHANV BLS HIGH to address invalid
time
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
44 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 12. External memory interface dynamic characteristics …continued
CL = 25 pF, Tamb = 40 °C
Symbol
Parameter
Conditions
Min
Typ Max
Unit
[2]
tBLSHDNV BLS HIGH to data invalid
time
(2 × Tcy(CCLK)) − 5
-
-
-
-
-
-
-
(2 × Tcy(CCLK)) + 5 ns
tCHDV
XCLK HIGH to data valid
time
-
-
-
-
-
-
10
10
10
10
10
10
ns
ns
ns
ns
ns
ns
tCHWEL
tCHBLSL
tCHWEH
tCHBLSH
tCHDNV
XCLK HIGH to WE LOW
time
XCLK HIGH to BLS LOW
time
XCLK HIGH to WE HIGH
time
XCLK HIGH to BLS HIGH
time
XCLK HIGH to data invalid
time
[1] Except on initial access, in which case the address is set up Tcy(CCLK) earlier.
[2] Tcy(CCLK) = 1⁄CCLK
.
[3] Latest of address valid, CS LOW, OE LOW to data valid.
[4] Address valid to data valid.
[5] Earliest of CS HIGH, OE HIGH, address change to data invalid.
Table 13. Standard read access specifications
Access cycle
Max frequency
WST[1] setting
Memory access time requirement
WST ≥ 0; round up to
integer
standard read
2 + WST1
RAM + 20 ns
t
RAM + 20 ns
tRAM ≤ tcy(CCLK) × (2 + WST1) – 20 ns
f MAX
f MAX
f MAX
f MAX
≤
≤
≤
≤
--------------------------------
WST1 ≥
WST2 ≥
– 2
--------------------------------
tcy(CCLK)
t
standard write
1 + WST2
t
WRITE – tCYC + 5
tWRITE ≤ tcy(CCLK) × (1 + WST2) – 5 ns
tINIT ≤ tcy(CCLK) × (2 + WST1) – 20 ns
---------------------------------
-------------------------------------------
t
WRITE + 5 ns
tcy(CCLK)
burst read - initial
burst read - subsequent 3×
2 + WST1
tINIT + 20 ns
-------------------------------
WST1 ≥
– 2
-------------------------------
tINIT + 20 ns
tcy(CCLK)
N/A
1
t
ROM ≤ tcy(CCLK) – 20 ns
--------------------------------
tROM + 20 ns
[1] See the LPC2119/2129/2194/2292/2294 User Manual for a description of the WSTn bits.
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
45 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
9.1 Timing
XCLK
t
t
CSHOEH
CSLAV
CS
addr
data
t
t
h(D)
am
t
CSLOEL
t
t
OEHANV
OELAV
OE
t
t
CHOEH
CHOEL
002aaa749
Fig 22. External memory read access
XCLK
CS
t
CSLDV
t
AVCSL
t
WELWEH
t
CSLWEL
t
BLSLBLSH
BLS/WE
t
WEHANV
t
t
WELDV
CSLBLSL
t
BLSHANV
addr
data
t
t
WEHDNV
BLSHDNV
t
CSLDV
OE
002aaa750
Fig 23. External memory write access
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
46 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
t
CHCX
t
t
t
CHCL
CLCX
CLCH
T
cy(clk)
002aaa907
Fig 24. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
47 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
10. Package outline
LQFP144: plastic low profile quad flat package; 144 leads; body 20 x 20 x 1.4 mm
SOT486-1
y
X
A
108
109
73
72
Z
E
e
H
A
E
2
A
E
(A )
3
A
1
θ
w M
p
L
p
b
L
pin 1 index
detail X
37
144
1
36
v
M
A
Z
w M
D
b
p
e
D
B
H
v
M
B
D
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
D
H
L
L
v
w
y
Z
Z
E
θ
1
2
3
p
E
p
D
max.
7o
0o
0.15 1.45
0.05 1.35
0.27 0.20 20.1 20.1
0.17 0.09 19.9 19.9
22.15 22.15
21.85 21.85
0.75
0.45
1.4
1.1
1.4
1.1
mm
1.6
0.25
1
0.2 0.08 0.08
0.5
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
00-03-14
03-02-20
SOT486-1
136E23
MS-026
Fig 25. Package outline SOT486-1 (LQFP144)
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
48 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
TFBGA144: plastic thin fine-pitch ball grid array package; 144 balls
SOT569-2
D
B
A
ball A1
index area
A
2
E
A
A
1
detail X
e
1
C
M
M
v
C
C
A
B
e
b
y
y
w
C
1
N
M
K
H
L
J
e
e
2
G
E
C
A
F
D
B
ball A1
index area
1
3
5
7
9
11
13
2
4
6
8
10
12
X
0
5
scale
10 mm
DIMENSIONS (mm are the original dimensions)
UNIT
A
A
1
A
2
b
D
E
e
e
1
e
2
v
w
y
y
1
max 1.20 0.40 0.80 0.50 12.1 12.1
nom 1.05 0.35 0.70 0.45 12.0 12.0
mm
0.8
9.6
9.6
0.15 0.05
0.1
0.08
min
0.95 0.30 0.65 0.40 11.9 11.9
REFERENCES
JEDEC JEITA
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
08-01-29
08-03-14
SOT569-2
Fig 26. Package outline SOT569-2 (TFBGA144)
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
49 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
11. Abbreviations
Table 14. Acronym list
Acronym
ADC
AHB
AMBA
APB
Description
Analog-to-Digital Converter
Advanced High-performance Bus
Advanced Microcontroller Bus Architecture
Advanced Peripheral Bus
Controller Area Network
CAN
CISC
FIFO
GPIO
I/O
Complex Instruction Set Computer
First In, First Out
General Purpose Input/Output
Input/Output
JTAG
LSB
Joint Test Action Group
Least Significant Bit
PLL
Phase-Locked Loop
PWM
RISC
SPI
Pulse Width Modulator
Reduced Instruction Set Computer
Serial Peripheral Interface
Static Random Access Memory
Synchronous Serial Interface
Synchronous Serial Port
SRAM
SSI
SSP
TTL
Transistor-Transistor Logic
Universal Asynchronous Receiver/Transmitter
UART
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
50 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
12. Revision history
Table 15. Revision history
Document ID
LPC2292_2294_7
Modifications:
Release date
20081204
Data sheet status
Change notice
Supersedes
Product data sheet
-
LPC2292_2294_6
• Figure 1 “Block diagram”: corrected high-speed GPIO ports 48 pins; P0/P1 only.
• Figure 24 “External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)”: removed
figure note row “VDD = 1.8 V”, updated graphic.
• Table 4 “Pin description”: pad descriptions corrected for pins P2[30], P2[31], P3[28], P3[30],
P3[31].
• Table 5 “Interrupt sources”: CAN and UART0/1 interrupt sources corrected.
• Table 7 “Static characteristics”: Vhys, moved 0.4 from Typ to Min column.
• Maximum frequency fosc for external oscillator and external crystal updated.
• Changed SOT569-1 to SOT569-2.
• Added overbar to indicate LOW-active for BLSn, CSn, OE, and WE
LPC2292_2294_6
Modifications:
20071210
Product data sheet
-
LPC2292_2294_5
• Type number LPC2292FBD144/01 has been added.
• Type number LPC2292FET144/01 has been added.
• Type number LPC2294HBD144/01 has been added.
• Details introduced with /01 devices on new peripherals/features (Fast I/O ports, SSP, CRP)
and enhancements to existing ones (UART0/1, Timers, ADC, and SPI) added.
• Power consumption measurements for LPC2292/2294/01 added.
• Description of JTAG pin TCK has been updated.
LPC2292_2294_5
LPC2292_2294_4
LPC2292_2294_3
LPC2292_2294-02
LPC2292_2294-01
20070215
20060711
20051101
20041223
20040205
Product data sheet
Product data sheet
Product data sheet
Product data
-
-
-
-
-
LPC2292_2294_4
LPC2292_2294_3
LPC2292_2294-02
LPC2292_2294-01
-
Preliminary data
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
51 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
13. Legal information
13.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
to result in personal injury, death or severe property or environmental
13.2 Definitions
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
13.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
13.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
I2C-bus — logo is a trademark of NXP B.V.
14. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
LPC2292_2294_7
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 7 — 4 December 2008
52 of 53
LPC2292/LPC2294
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
15. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
6.15.2
Features available in LPC2292/
LPC2294/01 only . . . . . . . . . . . . . . . . . . . . . . 23
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . 23
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Real-time clock. . . . . . . . . . . . . . . . . . . . . . . . 23
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Pulse width modulator . . . . . . . . . . . . . . . . . . 24
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
System control . . . . . . . . . . . . . . . . . . . . . . . . 25
Crystal oscillator. . . . . . . . . . . . . . . . . . . . . . . 25
PLL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Reset and wake-up timer . . . . . . . . . . . . . . . . 25
Code security (Code Read Protection - CRP) 26
External interrupt inputs. . . . . . . . . . . . . . . . . 26
Memory mapping control . . . . . . . . . . . . . . . . 26
Power control . . . . . . . . . . . . . . . . . . . . . . . . . 27
APB bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Emulation and debugging. . . . . . . . . . . . . . . . 27
EmbeddedICE . . . . . . . . . . . . . . . . . . . . . . . . 27
Embedded trace. . . . . . . . . . . . . . . . . . . . . . . 28
RealMonitor . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2
2.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Key features brought by LPC2292/
LPC2294/01 devices. . . . . . . . . . . . . . . . . . . . . 1
Key features common for all devices . . . . . . . . 1
6.16
6.16.1
6.17
6.17.1
6.18
6.18.1
6.19
6.19.1
6.19.2
6.19.3
6.19.4
6.19.5
6.19.6
6.19.7
6.19.8
6.20
2.2
3
3.1
4
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Ordering options. . . . . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5
5.1
5.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 5
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 8
6
Functional description . . . . . . . . . . . . . . . . . . 15
Architectural overview. . . . . . . . . . . . . . . . . . . 15
On-chip flash program memory . . . . . . . . . . . 15
On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . 16
Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 16
Interrupt controller . . . . . . . . . . . . . . . . . . . . . 17
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 17
Pin connect block . . . . . . . . . . . . . . . . . . . . . . 18
External memory controller. . . . . . . . . . . . . . . 18
General purpose parallel I/O (GPIO) and
6.1
6.2
6.3
6.4
6.5
6.5.1
6.6
6.7
6.8
6.20.1
6.20.2
6.20.3
7
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 29
Fast I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Features added with the Fast GPIO set of
8
8.1
Static characteristics . . . . . . . . . . . . . . . . . . . 30
Power consumption measurements for
LPC2292/01 and LPC2294/01 . . . . . . . . . . . . 34
6.8.1
6.8.2
registers available on LPC2292/
9
Dynamic characteristics. . . . . . . . . . . . . . . . . 42
Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 48
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 50
Revision history . . . . . . . . . . . . . . . . . . . . . . . 51
LPC2294/01 only . . . . . . . . . . . . . . . . . . . . . . 19
10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ADC features available in LPC2292/
LPC2294/01 only . . . . . . . . . . . . . . . . . . . . . . 19
CAN controllers and acceptance filter . . . . . . 20
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
UARTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
UART features available in LPC2292/
9.1
10
11
12
6.9
6.9.1
6.9.2
6.10
6.10.1
6.11
6.11.1
6.11.2
13
Legal information . . . . . . . . . . . . . . . . . . . . . . 52
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 52
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.1
13.2
13.3
13.4
LPC2294/01 only . . . . . . . . . . . . . . . . . . . . . . 20
I2C-bus serial I/O controller . . . . . . . . . . . . . . 20
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SPI serial I/O controller. . . . . . . . . . . . . . . . . . 21
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Features available in LPC2292/LPC2294/
14
15
Contact information . . . . . . . . . . . . . . . . . . . . 52
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6.12
6.12.1
6.13
6.13.1
6.13.2
01 only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SSP controller (LPC2292/94/01 only). . . . . . . 22
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
General purpose timers . . . . . . . . . . . . . . . . . 22
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.14
6.14.1
6.15
6.15.1
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2008.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 4 December 2008
Document identifier: LPC2292_2294_7
相关型号:
LPC2292FET144/00
16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface
NXP
LPC2292FET144/00,5
LPC2292/2294 - 16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface BGA 144-Pin
NXP
LPC2292FET144/01
16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface
NXP
LPC2292FET144/G
16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface
NXP
LPC2292_07
16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface
NXP
LPC2294
16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface
NXP
LPC2294HBD144
16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface
NXP
LPC2294HBD144/00
16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface
NXP
LPC2294HBD144/01
16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface
NXP
LPC2294HBD144/01,5
LPC2292/2294 - 16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface QFP 144-Pin
NXP
LPC2294JBD144
16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface
NXP
©2020 ICPDF网 联系我们和版权申明