首页 |元器件品牌

NTB0102GU [NXP]

Dual supply translating transceiver; auto direction sensing ; 3-state; 双电源转换收发器;自动方向感应;三态
NTB0102GU
型号： NTB0102GU
厂家： NXP    NXP
描述：

Dual supply translating transceiver; auto direction sensing ; 3-state
双电源转换收发器;自动方向感应;三态

线路驱动器或接收器 驱动程序和接口 接口集成电路
文件： 总26页 (文件大小：217K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
NTB0102  
Dual supply translating transceiver; auto direction sensing;  
3-state  
Rev. 2 — 28 April 2011  
Product data sheet  
1. General description  
The NTB0102 is a 2-bit, dual supply translating transceiver with auto direction sensing,  
that enables bidirectional voltage level translation. It features two 2-bit input-output ports  
(An and Bn), one output enable input (OE) and two supply pins (VCC(A) and VCC(B)). VCC(A)  
can be supplied at any voltage between 1.2 V and 3.6 V and VCC(B) can be supplied at any  
voltage between 1.65 V and 5.5 V, making the device suitable for translating between any  
of the low voltage nodes (1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V and 5.0 V).  
Pins An and OE are referenced to VCC(A) and pins Bn are referenced to VCC(B). A LOW  
level at pin OE causes the outputs to assume a high-impedance OFF-state. This device is  
fully specified for partial power-down applications using IOFF. The IOFF circuitry disables  
the output, preventing the damaging backflow current through the device when it is  
powered down.  
2. Features and benefits  
„ Wide supply voltage range:  
‹ VCC(A): 1.2 V to 3.6 V and VCC(B): 1.65 V to 5.5 V  
„ IOFF circuitry provides partial Power-down mode operation  
„ Inputs accept voltages up to 5.5 V  
„ ESD protection:  
‹ HBM JESD22-A114E Class 2 exceeds 2500 V for A port  
‹ HBM JESD22-A114E Class 3B exceeds 15000 V for B port  
‹ MM JESD22-A115-A exceeds 200 V  
‹ CDM JESD22-C101E exceeds 1500 V  
„ Latch-up performance exceeds 100 mA per JESD 78B Class II  
„ Multiple package options  
„ Specified from −40 °C to +85 °C and −40 °C to +125 °C  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
3. Ordering information  
Table 1.  
Ordering information  
Type number  
Package  
Temperature range Name  
Description  
Version  
NTB0102DP  
NTB0102GT  
NTB0102GD  
NTB0102GF  
NTB0102GU  
−40 °C to +125 °C  
−40 °C to +125 °C  
−40 °C to +125 °C  
−40 °C to +125 °C  
−40 °C to +125 °C  
TSSOP8 plastic thin shrink small outline package; 8 leads;  
body width 3 mm; lead length 0.5 mm  
SOT505-2  
XSON8  
plastic extremely thin small outline package; no leads; SOT833-1  
8 terminals; body 1 × 1.95 × 0.5 mm  
XSON8U plastic extremely thin small outline package; no leads; SOT996-2  
8 terminals; UTLP based; body 3 × 2 × 0.5 mm  
XSON8  
extremely thin small outline package; no leads;  
SOT1089  
8 terminals; body 1.35 × 1 × 0.5 mm  
XQFN10  
plastic, extremely thin quad flat package; no leads;  
SOT1160-1  
10 terminals; body 1.40 × 1.80 × 0.50 mm  
4. Marking  
Table 2.  
Marking  
Type number  
NTB0102DP  
NTB0102GT  
NTB0102GD  
NTB0102GF  
NTB0102GU  
Marking code[1]  
t02  
t02  
t02  
t2  
t2  
[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.  
5. Functional diagram  
6
OE  
4
A2  
1
B2  
5
A1  
8
B1  
V
CC(A)  
V
CC(B)  
001aal914  
Fig 1. Logic symbol  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
2 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
6. Pinning information  
6.1 Pinning  
NTB0102  
B2  
1
2
3
4
8
7
6
5
B1  
GND  
V
CC(B)  
NTB0102  
V
OE  
A1  
CC(A)  
A2  
1
2
3
4
8
7
6
5
B2  
B1  
GND  
V
CC(B)  
V
OE  
A1  
CC(A)  
A2  
001aam485  
Transparent top view  
001aam484  
Fig 2. Pin configuration SOT505-2 (TSSOP8)  
Fig 3. Pin configuration SOT833-1 (XSON8) and  
SOT1089 (XSON8)  
NTB0102  
terminal 1  
index area  
NTB0102  
B2  
1
2
3
4
8
7
6
5
B1  
A2  
1
2
7
6
n.c.  
GND  
V
CC(B)  
V
V
CC(B)  
CC(A)  
V
OE  
A1  
CC(A)  
A2  
001aam560  
001aam486  
Transparent top view  
Transparent top view  
Fig 4. Pin configuration SOT996-2 (XSON8U)  
Fig 5. Pin configuration SOT1160-1 (XQFN10)  
6.2 Pin description  
Table 3.  
Symbol  
Pin description  
Pin  
Description  
SOT505-2, SOT833-1, SOT1089 and SOT996-2 SOT1160-1  
B2, B1  
GND  
1, 8  
2
5, 8  
9
data input or output (referenced to VCC(B)  
)
)
ground (0 V)  
VCC(A)  
A2, A1  
3
2
supply voltage A  
4, 5  
1, 10  
data input or output (referenced to VCC(A)  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
3 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Table 3.  
Symbol  
Pin description …continued  
Pin  
SOT505-2, SOT833-1, SOT1089 and SOT996-2 SOT1160-1  
Description  
OE  
6
4
output enable input (active HIGH;  
referenced to VCC(A)  
supply voltage B  
not connected  
)
VCC(B)  
n.c.  
7
-
6
3, 7  
7. Functional description  
Table 4.  
Function table[1]  
Supply voltage  
VCC(A)  
Input  
OE  
L
Input/output  
VCC(B)  
An  
Bn  
1.2 V to VCC(B)  
1.2 V to VCC(B)  
GND[2]  
1.65 V to 5.5 V  
1.65 V to 5.5 V  
GND[2]  
Z
Z
H
input or output  
Z
output or input  
Z
X
[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state.  
[2] When either VCC(A) or VCC(B) is at GND level, the device goes into Power-down mode.  
8. Limiting values  
Table 5.  
Limiting values  
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).  
Symbol  
VCC(A)  
VCC(B)  
VI  
Parameter  
Conditions  
Min  
−0.5  
−0.5  
−0.5  
−0.5  
−0.5  
−50  
−50  
-
Max  
+6.5  
+6.5  
+6.5  
VCCO + 0.5  
+6.5  
-
Unit  
V
supply voltage A  
supply voltage B  
input voltage  
V
[1]  
[1][2][3]  
[1]  
V
VO  
output voltage  
Active mode  
V
Power-down or 3-state mode  
VI < 0 V  
V
IIK  
input clamping current  
output clamping current  
output current  
mA  
mA  
mA  
mA  
mA  
°C  
mW  
IOK  
IO  
VO < 0 V  
-
[2]  
VO = 0 V to VCCO  
ICC(A) or ICC(B)  
±50  
100  
-
ICC  
IGND  
Tstg  
Ptot  
supply current  
-
ground current  
−100  
−65  
-
storage temperature  
total power dissipation  
+150  
250  
[4]  
Tamb = −40 °C to +125 °C  
[1] The minimum input and minimum output voltage ratings may be exceeded if the input and output current ratings are observed.  
[2] VCCO is the supply voltage associated with the output.  
[3] VCCO + 0.5 V should not exceed 6.5 V.  
[4] For TSSOP8 package: above 55 °C the value of Ptot derates linearly with 2.5 mW/K.  
For XSON8 and XSON8U packages: above 118 °C the value of Ptot derates linearly with 7.8 mW/K.  
For XQFN10 package: above 128 °C the value of Ptot derates linearly with 11.5 mW/K.  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
4 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
9. Recommended operating conditions  
Table 6.  
Symbol  
VCC(A)  
VCC(B)  
VI  
Recommended operating conditions[1][2]  
Parameter  
Conditions  
Min  
1.2  
1.65  
0
Max  
3.6  
Unit  
V
supply voltage A  
supply voltage B  
input voltage  
5.5  
5.5  
V
V
VO  
output voltage  
Power-down or 3-state mode;  
CC(A) = 1.2 V to 3.6 V;  
V
VCC(B) = 1.65 V to 5.5 V  
A port  
B port  
0
3.6  
V
0
5.5  
V
Tamb  
ambient temperature  
−40  
+125  
40  
°C  
ns/V  
Δt/ΔV  
input transition rise and fall rate VCC(A) = 1.2 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
-
[1] The A and B sides of an unused I/O pair must be held in the same state, both at VCCI or both at GND.  
[2] VCC(A) must be less than or equal to VCC(B)  
.
10. Static characteristics  
Table 7.  
Typical static characteristics  
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); Tamb = 25 °C.  
Symbol Parameter  
Conditions  
Min  
Typ  
Max  
Unit  
VOH  
VOL  
II  
HIGH-level  
output voltage  
A port; VCC(A) = 1.2 V; IO = −20 μA  
-
1.1  
-
V
LOW-level  
output voltage  
A port; VCC(A) = 1.2 V; IO = 20 μA  
-
-
-
-
-
0.09  
-
V
input leakage  
current  
OE input; VI = 0 V to 3.6 V; VCC(A) = 1.2 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
-
-
-
-
±1  
±1  
±1  
±1  
μA  
μA  
μA  
μA  
[1]  
IOZ  
IOFF  
OFF-stateoutput A or B port; VO = 0 V to VCCO; VCC(A) = 1.2 V to 3.6 V;  
current  
VCC(B) = 1.65 V to 5.5 V  
power-off  
A port; VI or VO = 0 V to 3.6 V;  
leakage current VCC(A) = 0 V; VCC(B) = 0 V to 5.5 V  
B port; VI or VO = 0 V to 5.5 V;  
VCC(B) = 0 V; VCC(A) = 0 V to 3.6 V  
[2]  
ICC  
supply current  
VI = 0 V or VCCI; IO = 0 A  
ICC(A); VCC(A) = 1.2 V; VCC(B) = 1.65 V to 5.5 V  
ICC(B); VCC(A) = 1.2 V; VCC(B) = 1.65 V to 5.5 V  
ICC(A) + ICC(B); VCC(A) = 1.2 V; VCC(B) = 1.65 V to 5.5 V  
OE input; VCC(A) = 1.2 V to 3.6 V; VCC(B) = 1.65 V to 5.5 V  
-
-
-
-
0.05  
3.3  
-
-
-
-
μA  
μA  
μA  
pF  
3.5  
1.0  
CI  
input  
capacitance  
CI/O  
input/output  
capacitance  
A port; VCC(A) = 1.2 V to 3.6 V; VCC(B) = 1.65 V to 5.5 V  
B port; VCC(A) = 1.2 V to 3.6 V; VCC(B) = 1.65 V to 5.5 V  
-
-
4.0  
7.5  
-
-
pF  
pF  
[1] VCCO is the supply voltage associated with the output.  
[2] VCCI is the supply voltage associated with the input.  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
5 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Table 8.  
Typical supply current  
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); Tamb = 25 °C.  
VCC(A)  
VCC(B)  
Unit  
1.8 V  
2.5 V  
3.3 V  
5.0 V  
ICC(A)  
10  
10  
10  
-
ICC(B)  
10  
10  
10  
-
ICC(A)  
10  
10  
10  
10  
-
ICC(B)  
10  
10  
10  
10  
-
ICC(A)  
10  
ICC(B)  
20  
ICC(A)  
10  
ICC(B)  
1050  
650  
350  
40  
1.2 V  
1.5 V  
1.8 V  
2.5 V  
3.3 V  
nA  
nA  
nA  
nA  
nA  
10  
10  
10  
10  
10  
10  
10  
10  
10  
-
-
10  
10  
10  
10  
Table 9.  
Static characteristics  
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).  
Symbol Parameter  
Conditions  
−40 °C to +85 °C  
−40 °C to +125 °C  
Unit  
Min  
Max  
Min  
Max  
[1]  
[1]  
[2]  
VIH  
HIGH-level  
input voltage  
A or B port and OE input  
VCC(A) = 1.2 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
0.65VCCI  
-
0.65VCCI  
-
V
V
VIL  
LOW-level  
input voltage  
A or B port and OE input  
VCC(A) = 1.2 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
-
0.35VCCI  
-
0.35VCCI  
VOH  
HIGH-level  
IO = −20 μA  
output voltage  
A port; VCC(A) = 1.4 V to 3.6 V  
B port; VCC(B) = 1.65 V to 5.5 V  
IO = 20 μA  
VCCO − 0.4  
VCCO − 0.4  
-
-
VCCO − 0.4  
VCCO − 0.4  
-
-
V
V
[2]  
VOL  
LOW-level  
output voltage  
A port; VCC(A) = 1.4 V to 3.6 V  
B port; VCC(B) = 1.65 V to 5.5 V  
-
-
-
0.4  
0.4  
±2  
-
-
-
0.4  
0.4  
±5  
V
V
II  
input leakage OE input; VI = 0 V to 3.6 V;  
μA  
current  
VCC(A) = 1.2 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
[2]  
IOZ  
OFF-state  
A or B port; VO = 0 V or VCCO  
;
-
±2  
-
±10  
μA  
output current  
VCC(A) = 1.2 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
IOFF  
power-off  
leakage  
current  
A port; VI or VO = 0 V to 3.6 V;  
VCC(A) = 0 V; VCC(B) = 0 V to 5.5 V  
-
-
±2  
±2  
-
-
±10  
±10  
μA  
μA  
B port; VI or VO = 0 V to 5.5 V;  
VCC(B) = 0 V; VCC(A) = 0 V to 3.6 V  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
6 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Table 9.  
Static characteristics …continued  
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).  
Symbol Parameter Conditions −40 °C to +85 °C  
−40 °C to +125 °C  
Unit  
Min  
Max  
Min  
Max  
[1]  
ICC  
supply current VI = 0 V or VCCI; IO = 0 A  
ICC(A)  
OE = LOW;  
VCC(A) = 1.4 V to 3.6 V;  
-
-
3
3
-
-
15  
20  
μA  
μA  
VCC(B) = 1.65 V to 5.5 V  
OE = HIGH;  
VCC(A) = 1.4 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
V
CC(A) = 3.6 V; VCC(B) = 0 V  
-
-
2
-
-
15  
μA  
μA  
VCC(A) = 0 V; VCC(B) = 5.5 V  
ICC(B)  
−2  
−15  
OE = LOW;  
VCC(A) = 1.4 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
-
-
5
5
-
-
15  
20  
μA  
μA  
OE = HIGH;  
VCC(A) = 1.4 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
VCC(A) = 3.6 V; VCC(B) = 0 V  
VCC(A) = 0 V; VCC(B) = 5.5 V  
CC(A) + ICC(B)  
-
-
−2  
-
-
−15  
μA  
μA  
2
15  
I
VCC(A) = 1.4 V to 3.6 V;  
VCC(B) = 1.65 V to 5.5 V  
-
8
-
40  
μA  
[1] VCCI is the supply voltage associated with the input.  
[2] VCCO is the supply voltage associated with the output.  
11. Dynamic characteristics  
Table 10. Typical dynamic characteristics for temperature 25 °C[1]  
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for waveforms see Figure 6 and Figure 7.  
Symbol Parameter  
Conditions  
VCC(B)  
Unit  
1.8 V  
2.5 V  
3.3 V  
5.0 V  
VCC(A) = 1.2 V; Tamb = 25 °C  
tpd  
propagation delay A to B  
5.9  
5.6  
0.5  
6.9  
9.5  
81  
4.8  
4.8  
0.5  
6.9  
8.6  
69  
4.4  
4.5  
0.5  
6.9  
8.5  
83  
4.2  
4.4  
0.5  
6.9  
8.0  
68  
ns  
ns  
μs  
ns  
ns  
ns  
ns  
ns  
ns  
B to A  
ten  
enable time  
disable time  
OE to A, B  
[2]  
[2]  
tdis  
OE to A; no external load  
OE to B; no external load  
OE to A  
OE to B  
81  
69  
83  
68  
tt  
transition time  
A port  
4.0  
2.6  
4.0  
2.0  
4.1  
1.7  
4.1  
1.4  
B port  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
7 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Table 10. Typical dynamic characteristics for temperature 25 °C[1] …continued  
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for waveforms see Figure 6 and Figure 7.  
Symbol Parameter  
Conditions  
VCC(B)  
Unit  
1.8 V  
0.2  
15  
2.5 V  
0.2  
13  
3.3 V  
0.2  
13  
5.0 V  
0.2  
13  
[3]  
tsk(o)  
tW  
output skew time  
between channels  
data inputs  
ns  
pulse width  
data rate  
ns  
fdata  
70  
80  
80  
80  
Mbps  
[1] tpd is the same as tPLH and tPHL  
ten is the same as tPZL and tPZH  
tdis is the same as tPLZ and tPHZ  
tt is the same as tTHL and tTLH  
.
.
.
[2] Delay between OE going LOW and when the outputs are actually disabled.  
[3] Skew between any two outputs of the same package switching in the same direction.  
Table 11. Dynamic characteristics for temperature range −40 °C to +85 °C[1]  
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7.  
Symbol Parameter  
Conditions  
VCC(B)  
Unit  
1.8 V ± 0.15 V 2.5 V ± 0.2 V 3.3 V ± 0.3 V 5.0 V ± 0.5 V  
Min  
Max Min Max Min Max Min Max  
VCC(A) = 1.5 V ± 0.1 V  
tpd  
propagation  
delay  
A to B  
1.4  
0.9  
-
12.9  
14.2  
1.0  
1.2  
0.7  
-
10.1  
12.0  
1.0  
1.1  
0.4  
-
10.0  
11.7  
1.0  
0.8  
0.3  
-
9.9 ns  
B to A  
13.7 ns  
1.0 μs  
11.9 ns  
13.8 ns  
280 ns  
200 ns  
5.1 ns  
2.7 ns  
0.5 ns  
ten  
enable time  
OE to A, B  
[2]  
[2]  
tdis  
disable time OE to A; no external load  
1.0  
1.0  
-
11.9  
16.9  
320  
200  
5.1  
1.0  
1.0  
-
11.9  
15.2  
260  
200  
5.1  
1.0  
1.0  
-
11.9  
14.1  
260  
200  
5.1  
1.0  
1.0  
-
OE to B; no external load  
OE to A  
OE to B  
-
-
-
-
tt  
transition  
time  
A port  
B port  
0.9  
0.9  
-
0.9  
0.6  
-
0.9  
0.5  
-
0.9  
0.4  
-
4.7  
3.2  
2.5  
[3]  
tsk(o)  
output skew between channels  
time  
0.5  
0.5  
0.5  
tW  
pulse width  
data rate  
data inputs  
25  
-
-
25  
-
-
25  
-
-
25  
-
-
ns  
fdata  
40  
40  
40  
40 Mbps  
VCC(A) = 1.8 V ± 0.15 V  
tpd  
propagation  
delay  
A to B  
1.6  
1.5  
-
11.0  
12.0  
1.0  
1.4  
1.3  
-
7.7  
8.4  
1.3  
1.0  
-
6.8  
7.6  
1.2  
0.9  
-
6.5 ns  
7.1 ns  
1.0 μs  
11.0 ns  
12.1 ns  
230 ns  
200 ns  
4.1 ns  
2.7 ns  
B to A  
ten  
enable time  
OE to A, B  
1.0  
1.0  
[2]  
[2]  
tdis  
disable time OE to A; no external load  
1.0  
1.0  
-
11.0  
15.4  
260  
200  
4.1  
1.0  
1.0  
-
11.0  
13.5  
230  
200  
4.1  
1.0  
1.0  
-
11.0  
12.4  
230  
200  
4.1  
1.0  
1.0  
-
OE to B; no external load  
OE to A  
OE to B  
-
-
-
-
tt  
transition  
time  
A port  
B port  
0.8  
0.9  
0.8  
0.6  
0.8  
0.5  
0.8  
0.4  
4.7  
3.2  
2.5  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
8 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Table 11. Dynamic characteristics for temperature range −40 °C to +85 °C[1] …continued  
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7.  
Symbol Parameter  
Conditions  
VCC(B)  
Unit  
1.8 V ± 0.15 V 2.5 V ± 0.2 V 3.3 V ± 0.3 V 5.0 V ± 0.5 V  
Min  
Max Min Max Min Max Min Max  
[3]  
tsk(o)  
output skew between channels  
time  
-
0.5  
-
0.5  
-
0.5  
-
0.5 ns  
tW  
pulse width  
data rate  
data inputs  
20  
-
-
17  
-
-
17  
-
-
17  
-
-
ns  
fdata  
49  
60  
60  
60 Mbps  
VCC(A) = 2.5 V ± 0.2 V  
tpd  
propagation  
delay  
A to B  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.1  
1.2  
-
6.3  
6.6  
1.0  
9.2  
11.9  
200  
200  
3.0  
3.2  
0.5  
1.0  
1.1  
-
5.2  
5.1  
1.0  
0.9  
0.9  
-
4.7 ns  
4.4 ns  
1.0 μs  
9.2 ns  
10.2 ns  
200 ns  
200 ns  
3.0 ns  
2.7 ns  
0.5 ns  
B to A  
ten  
enable time  
OE to A, B  
[2]  
[2]  
tdis  
disable time OE to A; no external load  
1.0  
1.0  
-
1.0  
1.0  
-
9.2  
1.0  
1.0  
-
OE to B; no external load  
OE to A  
10.7  
200  
200  
3.0  
OE to B  
-
-
-
tt  
transition  
time  
A port  
B port  
0.7  
0.7  
-
0.7  
0.5  
-
0.7  
0.4  
-
2.5  
[3]  
tsk(o)  
output skew between channels  
time  
0.5  
tW  
pulse width  
data rate  
data inputs  
-
-
-
-
12  
-
-
10  
-
-
10  
-
-
ns  
fdata  
85  
100  
100 Mbps  
VCC(A) = 3.3 V ± 0.3 V  
tpd  
propagation  
delay  
A to B  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.9  
1.0  
-
4.7  
4.9  
1.0  
0.8  
0.9  
-
4.0 ns  
3.8 ns  
1.0 μs  
9.2 ns  
9.6 ns  
260 ns  
200 ns  
2.5 ns  
2.7 ns  
0.5 ns  
B to A  
ten  
enable time  
OE to A, B  
[2]  
[2]  
tdis  
disable time OE to A; no external load  
1.0  
1.0  
-
9.2  
1.0  
1.0  
-
OE to B; no external load  
OE to A  
10.1  
260  
200  
2.5  
OE to B  
-
-
tt  
transition  
time  
A port  
B port  
0.7  
0.5  
-
0.7  
0.4  
-
2.5  
[3]  
tsk(o)  
output skew between channels  
time  
0.5  
tW  
pulse width  
data rate  
data inputs  
-
-
-
-
-
-
-
-
10  
-
-
10  
-
-
ns  
fdata  
100  
100 Mbps  
[1] tpd is the same as tPLH and tPHL  
ten is the same as tPZL and tPZH  
tdis is the same as tPLZ and tPHZ  
tt is the same as tTHL and tTLH  
[2] Delay between OE going LOW and when the outputs are actually disabled.  
[3] Skew between any two outputs of the same package switching in the same direction.  
.
.
.
.
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
9 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Table 12. Dynamic characteristics for temperature range −40 °C to +125 °C[1]  
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7.  
Symbol Parameter  
Conditions  
VCC(B)  
Unit  
1.8 V ± 0.15 V 2.5 V ± 0.2 V 3.3 V ± 0.3 V 5.0 V ± 0.5 V  
Min  
Max Min Max Min Max Min Max  
VCC(A) = 1.5 V ± 0.1 V  
tpd  
propagation  
delay  
A to B  
1.4  
0.9  
-
15.9  
17.2  
1.0  
1.2  
0.7  
-
13.1  
15.0  
1.0  
1.1  
0.4  
-
13.0  
14.7  
1.0  
0.8  
0.3  
-
12.9 ns  
B to A  
16.7 ns  
1.0 μs  
12.5 ns  
14.6 ns  
300 ns  
220 ns  
7.1 ns  
4.7 ns  
0.5 ns  
ten  
enable time  
OE to A, B  
[2]  
[2]  
tdis  
disable time OE to A; no external load  
1.0  
1.0  
-
12.5  
18.1  
340  
220  
7.1  
1.0  
1.0  
-
12.5  
16.2  
280  
220  
7.1  
1.0  
1.0  
-
12.5  
14.9  
280  
220  
7.1  
1.0  
1.0  
-
OE to B; no external load  
OE to A  
OE to B  
-
-
-
-
tt  
transition  
time  
A port  
B port  
0.9  
0.9  
-
0.9  
0.6  
-
0.9  
0.5  
-
0.9  
0.4  
-
6.5  
5.2  
4.8  
[3]  
tsk(o)  
output skew between channels  
time  
0.5  
0.5  
0.5  
tW  
pulse width  
data rate  
data inputs  
25  
-
-
25  
-
-
25  
-
-
25  
-
-
ns  
fdata  
40  
40  
40  
40 Mbps  
VCC(A) = 1.8 V ± 0.15 V  
tpd  
propagation  
delay  
A to B  
1.6  
1.5  
-
14.0  
15.0  
1.0  
1.4  
1.3  
-
10.7  
11.4  
1.0  
1.3  
1.0  
-
9.8  
10.6  
1.0  
1.2  
0.9  
-
9.5 ns  
10.1 ns  
1.0 μs  
11.5 ns  
12.7 ns  
250 ns  
220 ns  
6.1 ns  
4.7 ns  
0.5 ns  
B to A  
ten  
enable time  
OE to A, B  
[2]  
[2]  
tdis  
disable time OE to A; no external load  
1.0  
1.0  
-
11.5  
16.5  
280  
220  
6.2  
1.0  
1.0  
-
11.5  
14.5  
250  
220  
6.1  
1.0  
1.0  
-
11.5  
13.3  
250  
220  
6.1  
1.0  
1.0  
-
OE to B; no external load  
OE to A  
OE to B  
-
-
-
-
tt  
transition  
time  
A port  
B port  
0.8  
0.9  
-
0.8  
0.6  
-
0.8  
0.5  
-
0.8  
0.4  
-
5.8  
5.2  
4.8  
[3]  
tsk(o)  
output skew between channels  
time  
0.5  
0.5  
0.5  
tW  
pulse width  
data rate  
data inputs  
22  
-
-
19  
-
-
19  
-
-
19  
-
-
ns  
fdata  
45  
55  
55  
55 Mbps  
VCC(A) = 2.5 V ± 0.2 V  
tpd  
propagation  
delay  
A to B  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.1  
1.2  
-
9.3  
9.6  
1.0  
1.1  
-
8.2  
8.1  
0.9  
0.9  
-
7.7 ns  
7.4 ns  
1.0 μs  
9.6 ns  
10.8 ns  
220 ns  
220 ns  
5.0 ns  
4.7 ns  
B to A  
ten  
enable time  
OE to A, B  
1.0  
1.0  
[2]  
[2]  
tdis  
disable time OE to A; no external load  
1.0  
1.0  
-
9.6  
1.0  
1.0  
-
9.6  
1.0  
1.0  
-
OE to B; no external load  
OE to A  
12.6  
220  
220  
5.0  
11.4  
220  
220  
5.0  
OE to B  
-
-
-
tt  
transition  
time  
A port  
B port  
0.7  
0.7  
0.7  
0.5  
0.7  
0.4  
4.6  
4.8  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
10 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Table 12. Dynamic characteristics for temperature range −40 °C to +125 °C[1] …continued  
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7.  
Symbol Parameter  
Conditions  
VCC(B)  
Unit  
1.8 V ± 0.15 V 2.5 V ± 0.2 V 3.3 V ± 0.3 V 5.0 V ± 0.5 V  
Min  
Max Min Max Min Max Min Max  
[3]  
tsk(o)  
output skew between channels  
time  
-
-
-
0.5  
-
0.5  
-
0.5 ns  
tW  
pulse width  
data rate  
data inputs;  
-
-
-
-
14  
-
-
13  
-
-
10  
-
-
ns  
fdata  
75  
80  
100 Mbps  
VCC(A) = 3.3 V ± 0.3 V  
tpd  
propagation  
delay  
A to B  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.9  
1.0  
-
7.7  
7.9  
1.0  
0.8  
0.9  
-
7.0 ns  
6.8 ns  
1.0 μs  
9.5 ns  
9.6 ns  
280 ns  
220 ns  
4.5 ns  
4.7 ns  
0.5 ns  
B to A  
ten  
enable time  
OE to A, B  
[2]  
[2]  
tdis  
disable time OE to A; no external load  
1.0  
1.0  
-
9.5  
1.0  
1.0  
-
OE to B; no external load  
OE to A  
10.7  
280  
220  
4.5  
OE to B  
-
-
tt  
transition  
time  
A port  
B port  
0.7  
0.5  
-
0.7  
0.4  
-
4.1  
[3]  
tsk(o)  
output skew between channels  
time  
0.5  
tW  
pulse width  
data rate  
data inputs  
-
-
-
-
-
-
-
-
10  
-
-
10  
-
-
ns  
fdata  
100  
100 Mbps  
[1] tpd is the same as tPLH and tPHL  
ten is the same as tPZL and tPZH  
.
.
tdis is the same as tPLZ and tPHZ  
.
tt is the same as tTHL and tTLH.  
[2] Delay between OE going LOW and when the outputs are actually disabled.  
[3] Skew between any two outputs of the same package switching in the same direction.  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
11 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Table 13. Typical power dissipation capacitance  
Voltages are referenced to GND (ground = 0 V).[1][2]  
Symbol Parameter  
Conditions  
VCC(A)  
1.8 V  
VCC(B)  
1.8 V  
Unit  
1.2 V  
1.8 V  
1.2 V  
5.0 V  
1.5 V  
1.8 V  
2.5 V  
2.5 V  
2.5 V  
5.0 V  
3.3 V  
3.3 V  
to  
5.0 V  
Tamb = 25 °C  
CPD  
power  
dissipation  
capacitance  
outputs enabled; OE = VCC(A)  
A port: (direction A to B)  
A port: (direction B to A)  
B port: (direction A to B)  
B port: (direction B to A)  
outputs disabled; OE = GND  
A port: (direction A to B)  
A port: (direction B to A)  
B port: (direction A to B)  
B port: (direction B to A)  
5
8
5
8
5
8
5
8
5
8
5
8
5
8
pF  
pF  
pF  
pF  
18  
13  
18  
16  
18  
12  
18  
12  
18  
12  
18  
12  
18  
13  
0.12  
0.01  
0.01  
0.07  
0.12  
0.01  
0.01  
0.09  
0.04  
0.01  
0.01  
0.07  
0.05  
0.01  
0.01  
0.07  
0.08  
0.01  
0.01  
0.05  
0.08  
0.01  
0.01  
0.09  
0.07 pF  
0.01 pF  
0.01 pF  
0.09 pF  
[1] CPD is used to determine the dynamic power dissipation (PD in μW).  
PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where:  
fi = input frequency in MHz;  
fo = output frequency in MHz;  
CL = load capacitance in pF;  
VCC = supply voltage in V;  
N = number of inputs switching;  
Σ(CL × VCC2 × fo) = sum of the outputs.  
[2] fi = 10 MHz; VI = GND to VCC; tr = tf = 1 ns; CL = 0 pF; RL = ∞ Ω.  
12. Waveforms  
V
I
An, Bn  
input  
V
M
GND  
t
t
PHL  
PLH  
V
OH  
90 %  
Bn, An  
output  
V
M
10 %  
V
OL  
t
t
THL  
TLH  
001aal918  
Measurement points are given in Table 14.  
VOL and VOH are typical output voltage levels that occur with the output load.  
Fig 6. Data input (An, Bn) to data output (Bn, An) propagation delay times  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
12 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
V
I
OE input  
V
M
GND  
t
t
PLZ  
PZL  
V
CCO  
output  
V
LOW-to-OFF  
OFF-to-LOW  
M
V
X
V
OL  
t
t
PHZ  
PZH  
V
OH  
V
Y
output  
HIGH-to-OFF  
OFF-to-HIGH  
V
M
GND  
outputs  
enabled  
outputs  
disabled  
outputs  
enabled  
001aal919  
Measurement points are given in Table 14.  
VOL and VOH are typical output voltage levels that occur with the output load.  
Fig 7. Enable and disable times  
Table 14. Measurement points[1]  
Supply voltage  
VCCO  
Input  
Output  
VM  
VM  
VX  
VY  
1.2 V  
0.5VCCI  
0.5VCCI  
0.5VCCI  
0.5VCCI  
0.5VCCI  
0.5VCCI  
0.5VCCO  
0.5VCCO  
0.5VCCO  
0.5VCCO  
0.5VCCO  
0.5VCCO  
VOL + 0.1 V  
VOL + 0.1 V  
VOL + 0.15 V  
VOL + 0.15 V  
VOL + 0.3 V  
VOL + 0.3 V  
VOH − 0.1 V  
VOH − 0.1 V  
VOH − 0.15 V  
VOH − 0.15 V  
VOH − 0.3 V  
VOH − 0.3 V  
1.5 V ± 0.1 V  
1.8 V ± 0.15 V  
2.5 V ± 0.2 V  
3.3 V ± 0.3 V  
5.0 V ± 0.5 V  
[1] VCCI is the supply voltage associated with the input and VCCO is the supply voltage associated with the output.  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
13 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
t
W
V
I
90 %  
negative  
pulse  
V
M
V
M
10 %  
0 V  
t
f
t
r
t
r
t
f
V
I
90 %  
positive  
pulse  
V
M
V
M
10 %  
0 V  
t
W
V
EXT  
V
CC  
R
L
L
V
V
O
I
G
DUT  
C
R
L
001aal920  
Test data is given in Table 15.  
All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz; ZO = 50 Ω; dV/dt ≥ 1.0 V/ns.  
RL = Load resistance.  
CL = Load capacitance including jig and probe capacitance.  
VEXT = External voltage for measuring switching times.  
Fig 8. Test circuit for measuring switching times  
Table 15. Test data  
Supply voltage  
VCC(A) VCC(B)  
Input  
VI[1]  
Load  
CL  
VEXT  
[2]  
[3]  
Δt/ΔV  
RL  
tPLH, tPHL tPZH, tPHZ tPZL, tPLZ  
1.2 V to 3.6 V 1.65 V to 5.5 V VCCI  
≤ 1.0 ns/V  
15 pF  
50 kΩ, 1 MΩ open  
open  
2VCCO  
[1] VCCI is the supply voltage associated with the input.  
[2] For measuring data rate, pulse width, propagation delay and output rise and fall measurements, RL = 1 MΩ; for measuring enable and  
disable times, RL = 50 kΩ.  
[3] VCCO is the supply voltage associated with the output.  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
14 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
13. Application information  
13.1 Applications  
Voltage level-translation applications. The NTB0102 can be used to interface between  
devices or systems operating at different supply voltages. See Figure 9 for a typical  
operating circuit using the NTB0102.  
1.8 V  
3.3 V  
1.8 V  
V
CC(A)  
V
CC(B)  
3.3 V  
0.1 μF  
0.1 μF  
SYSTEM  
SYSTEM  
CONTROLLER  
OE  
NTB0102  
A1  
A2  
B1  
B2  
DATA  
DATA  
GND  
001aam487  
Fig 9. Typical operating circuit  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
15 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
13.2 Architecture  
The architecture of the NTB0102 is shown in Figure 10. The device does not require an  
extra input signal to control the direction of data flow from A to B or from B to A. In a static  
state, the output drivers of the NTB0102 can maintain a defined output level, but the  
output architecture is designed to be weak, so that they can be overdriven by an external  
driver when data on the bus starts flowing in the opposite direction. The output of one-shot  
circuits detect rising or falling edges on the A or B ports. During a rising edge, the  
one-shot circuits turn on the PMOS transistors (T1, T3) for a short duration, accelerating  
the LOW-to-HIGH transition. Similarly, during a falling edge, the one-shot circuits turn on  
the NMOS transistors (T2, T4) for a short duration, accelerating the HIGH-to-LOW  
transition. During output transitions the typical output impedance is 70 Ω at VCCO = 1.2 V  
to 1.8 V, 50 Ω at VCCO = 1.8 V to 3.3 V and 40 Ω at VCCO = 3.3 V to 5.0 V.  
V
CC(A)  
V
CC(B)  
ONE  
SHOT  
T1  
4 kΩ  
T2  
ONE  
SHOT  
B
A
ONE  
SHOT  
T3  
4 kΩ  
T4  
ONE  
SHOT  
001aal921  
Fig 10. Architecture of NTB0102 I/O cell (one channel)  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
16 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
13.3 Input driver requirements  
For correct operation, the device driving the data I/Os of the NTB0102 must have a  
minimum drive capability of ±2 mA See Figure 11 for a plot of typical input current versus  
input voltage.  
I
I
V /4 kΩ  
T
V
I
−(V − V )/4 kΩ  
D
T
001aal922  
VT: input threshold voltage of the NTB0102 (typically VCCI / 2).  
VD: supply voltage of the external driver.  
Fig 11. Typical input current versus input voltage graph  
13.4 Power-up  
During operation VCC(A) must never be higher than VCC(B), however during power-up  
VCC(A) ≥ VCC(B) does not damage the device, so either power supply can be ramped up  
first. There is no special power-up sequencing required. The NTB0102 includes circuitry  
that disables all output ports when either VCC(A) or VCC(B) is switched off.  
13.5 Enable and disable  
An output enable input (OE) is used to disable the device. Setting OE = LOW causes all  
I/Os to assume the high-impedance OFF-state. The disable time (tdis with no external  
load) indicates the delay between when OE goes LOW and when outputs actually  
become disabled. The enable time (ten) indicates the amount of time the user must allow  
for one one-shot circuitry to become operational after OE is taken HIGH. To ensure the  
high-impedance OFF-state during power-up or power-down, pin OE should be tied to  
GND through a pull-down resistor, the minimum value of the resistor is determined by the  
current-sourcing capability of the driver.  
13.6 Pull-up or pull-down resistors on I/O lines  
As mentioned previously the NTB0102 is designed with low static drive strength to drive  
capacitive loads of up to 70 pF. To avoid output contention issues, any pull-up or  
pull-down resistors used must be above 50 kΩ. For this reason the NTB0102 is not  
recommended for use in open drain driver applications such as 1-Wire or I2C-bus. For  
these applications, the NTS0102 level translator is recommended.  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
17 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
14. Package outline  
TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm  
SOT505-2  
D
E
A
X
c
H
v
M
y
A
E
Z
5
8
A
2
A
(A )  
3
A
1
pin 1 index  
θ
L
p
L
detail X  
1
4
e
w
M
b
p
0
2.5  
5 mm  
scale  
DIMENSIONS (mm are the original dimensions)  
A
(1)  
(1)  
(1)  
A
A
A
b
c
D
E
e
H
E
L
L
p
UNIT  
v
w
y
Z
θ
1
2
3
p
max.  
0.15  
0.00  
0.95  
0.75  
0.38  
0.22  
0.18  
0.08  
3.1  
2.9  
3.1  
2.9  
4.1  
3.9  
0.47  
0.33  
0.70  
0.35  
8°  
0°  
mm  
1.1  
0.65  
0.25  
0.5  
0.2  
0.13  
0.1  
Note  
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.  
REFERENCES  
OUTLINE  
EUROPEAN  
PROJECTION  
ISSUE DATE  
VERSION  
IEC  
JEDEC  
JEITA  
02-01-16  
SOT505-2  
- - -  
Fig 12. Package outline SOT505-2 (TSSOP8)  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
18 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm  
SOT833-1  
b
1
2
3
4
4×  
(2)  
L
L
1
e
8
7
6
5
e
1
e
1
e
1
8×  
A
(2)  
A
1
D
E
terminal 1  
index area  
0
1
2 mm  
scale  
DIMENSIONS (mm are the original dimensions)  
(1)  
A
A
1
UNIT  
b
D
E
e
e
1
L
L
1
max max  
0.25  
0.17  
2.0  
1.9  
1.05  
0.95  
0.35 0.40  
0.27 0.32  
mm  
0.5 0.04  
0.6  
0.5  
Notes  
1. Including plating thickness.  
2. Can be visible in some manufacturing processes.  
REFERENCES  
OUTLINE  
VERSION  
EUROPEAN  
PROJECTION  
ISSUE DATE  
IEC  
JEDEC  
JEITA  
- - -  
07-11-14  
07-12-07  
SOT833-1  
- - -  
MO-252  
Fig 13. Package outline SOT833-1 (XSON8)  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
19 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
XSON8U: plastic extremely thin small outline package; no leads;  
8 terminals; UTLP based; body 3 x 2 x 0.5 mm  
SOT996-2  
D
B
A
E
A
A
1
detail X  
terminal 1  
index area  
e
1
C
M
M
v
w
C A  
C
B
b
e
L
1
y
1
y
C
1
4
L
2
L
8
5
X
0
1
2 mm  
scale  
DIMENSIONS (mm are the original dimensions)  
A
UNIT  
A
1
b
D
E
e
e
1
L
L
L
v
w
y
y
1
1
2
max  
0.05 0.35  
0.00 0.15  
2.1  
1.9  
3.1  
2.9  
0.5  
0.3  
0.15  
0.05  
0.6  
0.4  
mm  
0.5  
0.5  
1.5  
0.1  
0.05 0.05  
0.1  
REFERENCES  
OUTLINE  
VERSION  
EUROPEAN  
PROJECTION  
ISSUE DATE  
IEC  
- - -  
JEDEC  
JEITA  
07-12-18  
07-12-21  
SOT996-2  
- - -  
Fig 14. Package outline SOT996-2 (XSON8U)  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
20 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
XSON8: extremely thin small outline package; no leads;  
8 terminals; body 1.35 x 1 x 0.5 mm  
SOT1089  
E
terminal 1  
index area  
D
A
A
1
detail X  
(2)  
(4×)  
e
L
(2)  
(8×)  
b
4
5
e
1
1
8
terminal 1  
index area  
L
1
X
0
0.5  
1 mm  
scale  
Dimensions  
Unit  
(1)  
A
A
1
b
D
E
e
e
1
L
L
1
max 0.5 0.04 0.20 1.40 1.05  
0.35 0.40  
0.15 1.35 1.00 0.55 0.35 0.30 0.35  
0.12 1.30 0.95 0.27 0.32  
mm nom  
min  
Note  
1. Including plating thickness.  
2. Visible depending upon used manufacturing technology.  
sot1089_po  
References  
Outline  
version  
European  
projection  
Issue date  
IEC  
JEDEC  
JEITA  
10-04-09  
10-04-12  
SOT1089  
MO-252  
Fig 15. Package outline SOT1089 (XSON8)  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
21 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
XQFN10: plastic, extremely thin quad flat package; no leads;  
10 terminals; body 1.40 x 1.80 x 0.50 mm  
SOT1160-1  
X
D
B
A
E
terminal 1  
index area  
A
A
1
A
3
detail X  
e
1
e
C
v
w
C A  
B
C
b
y
C
1
y
3
5
L
2
1
6
7
e
2
terminal 1  
index area  
10  
8
L
1
0
1
2 mm  
w
scale  
Dimensions  
(1)  
Unit  
A
A
1
A
3
b
D
E
e
e
1
e
2
L
L
1
v
y
y
1
max 0.5 0.05  
mm nom  
min  
0.25 1.5 1.9  
0.127 0.20 1.4 1.8 0.4 0.8 0.4 0.40 0.50 0.1 0.05 0.05 0.05  
0.15 1.3 1.7 0.35 0.45  
0.45 0.55  
0.00  
Note  
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.  
sot1160-1_po  
References  
Outline  
version  
European  
projection  
Issue date  
IEC  
- - -  
JEDEC  
- - -  
JEITA  
- - -  
09-12-28  
09-12-29  
SOT1160-1  
Fig 16. Package outline SOT1160-1 (XQFN10)  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
22 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
15. Abbreviations  
Table 16. Abbreviations  
Acronym  
CDM  
Description  
Charged Device Model  
DUT  
Device Under Test  
ESD  
ElectroStatic Discharge  
Human Body Model  
HBM  
MM  
Machine Model  
NMOS  
PMOS  
PRR  
N-type Metal Oxide Semiconductor  
P-type Metal Oxide Semiconductor  
Pulse Repetition Rate  
16. Revision history  
Table 17. Revision history  
Document ID  
NTB0102 v.2  
Modifications:  
NTB0102 v.1  
Release date  
20110428  
Data sheet status  
Change notice  
Supersedes  
Product data sheet  
-
NTB0102 v.1  
• Added Table 8: total supply current (typical).  
20100922 Product data sheet  
-
-
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
23 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
17. Legal information  
17.1 Data sheet status  
Document status[1][2]  
Product status[3]  
Development  
Definition  
Objective [short] data sheet  
This document contains data from the objective specification for product development.  
This document contains data from the preliminary specification.  
This document contains the product specification.  
Preliminary [short] data sheet Qualification  
Product [short] data sheet Production  
[1]  
[2]  
[3]  
Please consult the most recently issued document before initiating or completing a design.  
The term ‘short data sheet’ is explained in section “Definitions”.  
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status  
information is available on the Internet at URL http://www.nxp.com.  
suitable for use in medical, military, aircraft, space or life support equipment,  
17.2 Definitions  
nor in applications where failure or malfunction of an NXP Semiconductors  
product can reasonably be expected to result in personal injury, death or  
severe property or environmental damage. NXP Semiconductors accepts no  
liability for inclusion and/or use of NXP Semiconductors products in such  
equipment or applications and therefore such inclusion and/or use is at the  
customer’s own risk.  
Draft — The document is a draft version only. The content is still under  
internal review and subject to formal approval, which may result in  
modifications or additions. NXP Semiconductors does not give any  
representations or warranties as to the accuracy or completeness of  
information included herein and shall have no liability for the consequences of  
use of such information.  
Applications — Applications that are described herein for any of these  
products are for illustrative purposes only. NXP Semiconductors makes no  
representation or warranty that such applications will be suitable for the  
specified use without further testing or modification.  
Short data sheet — A short data sheet is an extract from a full data sheet  
with the same product type number(s) and title. A short data sheet is intended  
for quick reference only and should not be relied upon to contain detailed and  
full information. For detailed and full information see the relevant full data  
sheet, which is available on request via the local NXP Semiconductors sales  
office. In case of any inconsistency or conflict with the short data sheet, the  
full data sheet shall prevail.  
Customers are responsible for the design and operation of their applications  
and products using NXP Semiconductors products, and NXP Semiconductors  
accepts no liability for any assistance with applications or customer product  
design. It is customer’s sole responsibility to determine whether the NXP  
Semiconductors product is suitable and fit for the customer’s applications and  
products planned, as well as for the planned application and use of  
customer’s third party customer(s). Customers should provide appropriate  
design and operating safeguards to minimize the risks associated with their  
applications and products.  
Product specification — The information and data provided in a Product  
data sheet shall define the specification of the product as agreed between  
NXP Semiconductors and its customer, unless NXP Semiconductors and  
customer have explicitly agreed otherwise in writing. In no event however,  
shall an agreement be valid in which the NXP Semiconductors product is  
deemed to offer functions and qualities beyond those described in the  
Product data sheet.  
NXP Semiconductors does not accept any liability related to any default,  
damage, costs or problem which is based on any weakness or default in the  
customer’s applications or products, or the application or use by customer’s  
third party customer(s). Customer is responsible for doing all necessary  
testing for the customer’s applications and products using NXP  
Semiconductors products in order to avoid a default of the applications and  
the products or of the application or use by customer’s third party  
customer(s). NXP does not accept any liability in this respect.  
17.3 Disclaimers  
Limited warranty and liability — Information in this document is believed to  
be accurate and reliable. However, NXP Semiconductors does not give any  
representations or warranties, expressed or implied, as to the accuracy or  
completeness of such information and shall have no liability for the  
consequences of use of such information.  
Limiting values — Stress above one or more limiting values (as defined in  
the Absolute Maximum Ratings System of IEC 60134) will cause permanent  
damage to the device. Limiting values are stress ratings only and (proper)  
operation of the device at these or any other conditions above those given in  
the Recommended operating conditions section (if present) or the  
Characteristics sections of this document is not warranted. Constant or  
repeated exposure to limiting values will permanently and irreversibly affect  
the quality and reliability of the device.  
In no event shall NXP Semiconductors be liable for any indirect, incidental,  
punitive, special or consequential damages (including - without limitation - lost  
profits, lost savings, business interruption, costs related to the removal or  
replacement of any products or rework charges) whether or not such  
damages are based on tort (including negligence), warranty, breach of  
contract or any other legal theory.  
Terms and conditions of commercial sale — NXP Semiconductors  
products are sold subject to the general terms and conditions of commercial  
sale, as published at http://www.nxp.com/profile/terms, unless otherwise  
agreed in a valid written individual agreement. In case an individual  
agreement is concluded only the terms and conditions of the respective  
agreement shall apply. NXP Semiconductors hereby expressly objects to  
applying the customer’s general terms and conditions with regard to the  
purchase of NXP Semiconductors products by customer.  
Notwithstanding any damages that customer might incur for any reason  
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards  
customer for the products described herein shall be limited in accordance  
with the Terms and conditions of commercial sale of NXP Semiconductors.  
Right to make changes — NXP Semiconductors reserves the right to make  
changes to information published in this document, including without  
limitation specifications and product descriptions, at any time and without  
notice. This document supersedes and replaces all information supplied prior  
to the publication hereof.  
No offer to sell or license — Nothing in this document may be interpreted or  
construed as an offer to sell products that is open for acceptance or the grant,  
conveyance or implication of any license under any copyrights, patents or  
other industrial or intellectual property rights.  
Suitability for use in automotive applications — This NXP  
Semiconductors product has been qualified for use in automotive  
applications. The product is not designed, authorized or warranted to be  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
24 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
Export control — This document as well as the item(s) described herein  
may be subject to export control regulations. Export might require a prior  
authorization from national authorities.  
17.4 Trademarks  
Notice: All referenced brands, product names, service names and trademarks  
are the property of their respective owners.  
18. Contact information  
For more information, please visit: http://www.nxp.com  
For sales office addresses, please send an email to: salesaddresses@nxp.com  
NTB0102  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 28 April 2011  
25 of 26  
NTB0102  
NXP Semiconductors  
Dual supply translating transceiver; auto direction sensing; 3-state  
19. Contents  
1
2
3
4
5
General description. . . . . . . . . . . . . . . . . . . . . . 1  
Features and benefits . . . . . . . . . . . . . . . . . . . . 1  
Ordering information. . . . . . . . . . . . . . . . . . . . . 2  
Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2  
6
6.1  
6.2  
Pinning information. . . . . . . . . . . . . . . . . . . . . . 3  
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3  
7
Functional description . . . . . . . . . . . . . . . . . . . 4  
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Recommended operating conditions. . . . . . . . 5  
Static characteristics. . . . . . . . . . . . . . . . . . . . . 5  
Dynamic characteristics . . . . . . . . . . . . . . . . . . 7  
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
8
9
10  
11  
12  
13  
Application information. . . . . . . . . . . . . . . . . . 15  
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Input driver requirements . . . . . . . . . . . . . . . . 17  
Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Enable and disable. . . . . . . . . . . . . . . . . . . . . 17  
Pull-up or pull-down resistors on I/O lines . . . 17  
13.1  
13.2  
13.3  
13.4  
13.5  
13.6  
14  
15  
16  
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18  
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 23  
17  
Legal information. . . . . . . . . . . . . . . . . . . . . . . 24  
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 24  
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
17.1  
17.2  
17.3  
17.4  
18  
19  
Contact information. . . . . . . . . . . . . . . . . . . . . 25  
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Please be aware that important notices concerning this document and the product(s)  
described herein, have been included in section ‘Legal information’.  
© NXP B.V. 2011.  
All rights reserved.  
For more information, please visit: http://www.nxp.com  
For sales office addresses, please send an email to: salesaddresses@nxp.com  
Date of release: 28 April 2011  
Document identifier: NTB0102  

相关型号：

NTB0102GU,115

 NTB0102 - Dual supply translating transceiver; auto direction sensing; 3-state QFN 10-Pin
NXP

NTB0104

 Dual supply translating transceiver; auto direction sensing; 3-state
NXP

NTB0104BQ

 Dual supply translating transceiver; auto direction sensing; 3-state
NXP

NTB0104BQ,115

 NTB0104 - Dual supply translating transceiver; auto direction sensing; 3-state QFN 14-Pin
NXP

NTB0104BQ-Q100

 NTB0104 SERIES, 4-BIT TRANSCEIVER, TRUE OUTPUT, PQCC14, 2.50 X 3 MM, 0.85 MM HEIGHT, PLASTIC, MO-241, SOT762-1, QFN-14
NXP

NTB0104D

 Dual supply translating transceiver; auto direction sensing; 3-state
NXP

NTB0104D,118

 NTB0104D
NXP

NTB0104GU12

 Dual supply translating transceiver; auto direction sensing; 3-state
NXP

NTB0104GU16

 Dual supply translating transceiver; auto direction sensing; 3-state
NXP

NTB0104PW

 Dual supply translating transceiver; auto direction sensing; 3-state
NXP

NTB0104PW,118

 Dual supply translating transceiver; auto direction sensing; 3-state, SOT402-1 Package, Standard Marking, Reel Pack, SMD, 13&quot;
NXP

NTB0104UK

 IC NTB0104 SERIES, 4-BIT TRANSCEIVER, TRUE OUTPUT, PBGA12, 1.20 X 1.60 MM, 0.65 MM HEIGHT, WLCSP-12, Bus Driver/Transceiver
NXP
©2020 ICPDF网 联系我们和版权申明