NX3DV2567HR,115 [NXP]
NX3DV2567 - Low-ohmic four-pole double-throw analog switch QFN 16-Pin;型号: | NX3DV2567HR,115 |
厂家: | NXP |
描述: | NX3DV2567 - Low-ohmic four-pole double-throw analog switch QFN 16-Pin 输出元件 |
文件: | 总20页 (文件大小:183K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NX3DV2567
Low-ohmic four-pole double-throw analog switch
Rev. 2 — 9 November 2011
Product data sheet
1. General description
The NX3DV2567 is a four-pole double-throw analog switch (4PDT) optimized for
switching WLAN-SIM supply, data and control signals. It has one digital select input (S)
and four switches each with two independent input/outputs (nY0 and nY1) and a common
input/output (nZ). Schmitt trigger action at S makes the circuit tolerant to slower input rise
and fall times across the entire VCC range from 1.4 V to 4.3 V.
A low input voltage threshold allows pin S to be driven by lower level logic signals without
significant increase in supply current ICC. This makes it possible for the NX3DV2567 to
switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for logic level
translation.
The NX3DV2567 allows signals with amplitude up to VCC to be transmitted from nZ to nY0
or nY1; or from nY0 or nY1 to nZ..
2. Features and benefits
Wide supply voltage range from 1.4 V to 4.3 V
Very low ON resistance for supply path:
0.5 (typical) at VCC = 1.8 V
0.45 (typical) at VCC = 2.7 V
Low ON resistance for data path:
7 (typical) at VCC = 1.8 V
6 (typical) at VCC = 2.7 V
Low ON capacitance for data path
Wide 3 db bandwidth > 160 MHz
Break-before-make switching
High noise immunity
ESD protection:
HBM JESD22-A114F Class 3A exceeds 4000 V
HBM JESD22-A114F Class 3A I/O to GND exceeds 7000 V
CDM AEC-Q100-011 revision B exceeds 1000 V
CMOS low-power consumption
Latch-up performance exceeds 100 mA per JESD 78B Class II Level A
1.8 V control logic at VCC = 3.6 V
Control input accepts voltages above supply voltage
Very low supply current, even when input is below VCC
High current handling capability (350 mA continuous current under 3.3 V supply for
supply path switch)
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
Specified from 40 C to +85 C and from 40 C to +125 C
3. Applications
Cell phone, PDA, digital camera, printer and notebook
LCD monitor, TV and set-top box
4. Ordering information
Table 1.
Ordering information
Package
Temperature range Name
Type number
Description
Version
NX3DV2567HR 40 C to +125 C
HXQFN16U plastic thermal enhanced extremely thin quad flat
package; no leads; 16 terminals; UTLP based;
body 3 x 3 x 0.5 mm
SOT1039-1
NX3DV2567GU 40 C to +125 C
XQFN16
plastic, extremely thin quad flat package; no leads;
16 terminals; body 1.80 x 2.60 x 0.50 mm
SOT1161-1
5. Marking
Table 2.
Marking codes
Type number
NX3DV2567HR
NX3DV2567GU
Marking code
D60
D60
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
2 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
6. Functional diagram
SUPPLY PATH
SWITCH
1Y0
1Z
1Y1
DATA PATH
SWITCHES
2Y0
nY1
2Z
2Y1
nZ
3Y0
3Z
3Y1
nY0
S
4Y0
4Z
4Y1
S
to other three switches
001aam595
001aam596
Fig 1. Logic symbol
Fig 2. Logic diagram (one switch)
7. Pinning information
7.1 Pinning
terminal 1
index area
terminal 1
index area
1Y0
S
1
2
3
4
12 4Z
1Y0
S
1
2
3
4
12 4Z
11 4Y1
10 n.c.
NX3DV2567
11 4Y1
10 n.c.
NX3DV2567
2Y1
2Z
2Y1
2Z
9
3Y0
9
3Y0
001aam597
Transparent top view
Transparent top view
001aam598
Fig 3. Pin configuration SOT1039-1 (HXQFN16U)
Fig 4. Pin configuration SOT1161-1 (XQFN16)
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
3 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
7.2 Pin description
Table 3.
Symbol
1Y0
Pin description
Pin
Description
1
independent input or output (supply switch)
independent input or output (data switch)
select input
2Y0, 3Y0, 4Y0
S
5, 9, 13
2
1Y1
15
independent input or output (supply switch)
independent input or output (data switch)
common output or input (supply switch)
common output or input (data switch)
ground (0 V)
2Y1, 3Y1, 4Y1
1Z
3, 7, 11
16
2Z, 3Z, 4Z
GND
4, 8, 12
6
n.c.
10
not connected
VCC
14
supply voltage
8. Functional description
Table 4.
Function table[1]
Input S
Channel on
nY0
L
H
nY1
[1] H = HIGH voltage level; L = LOW voltage level.
9. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
VCC
VI
Parameter
Conditions
select input S
VI < 0.5 V
Min
0.5
0.5
0.5
50
-
Max
+4.6
+4.6
Unit
V
supply voltage
input voltage
[1]
[2]
V
VSW
IIK
switch voltage
input clamping current
VCC + 0.5 V
-
mA
ISK
switch clamping current VI < 0.5 V or VI > VCC + 0.5 V
50
mA
ISW
switch current
supply path switch
VSW > 0.5 V or VSW < VCC + 0.5 V;
source or sink current
-
-
350
500
mA
mA
VSW > 0.5 V or VSW < VCC + 0.5 V;
pulsed at 1 ms duration, < 10 % duty cycle;
peak current
data path switch
VSW > 0.5 V or VSW < VCC + 0.5 V;
-
128
mA
source or sink current
Tstg
storage temperature
65
+150
C
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
4 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
Table 5.
Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
Conditions
Min
Max
Unit
[3][4]
Ptot
total power dissipation
Tamb = 40 C to +125 C
-
250
mW
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
[3] For HXQFN16U package: above 135 C the value of Ptot derates linearly with 16.9 mW/K.
[4] For XQFN16 package: above 133 C the value of Ptot derates linearly with 14.5 mW/K.
10. Recommended operating conditions
Table 6.
Recommended operating conditions
Symbol Parameter
Conditions
Min
1.4
0
Max
4.3
Unit
V
VCC
VI
supply voltage
input voltage
select input S
4.3
V
[1]
[2]
VSW
Tamb
t/V
switch voltage
0
VCC
+125
200
V
ambient temperature
input transition rise and fall rate
40
-
C
ns/V
VCC = 1.4 V to 4.3 V
[1] To avoid sinking GND current from terminal nZ when switch current flows in terminal nYn, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no GND current will flow from terminal nYn. In this case, there
is no limit for the voltage drop across the switch.
[2] Applies to control signal levels.
11. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
Tamb = 25 C
Tamb = 40 C to +125 C Unit
Min
Typ
Max
Min
Max
Max
(85 C) (125 C)
VIH
HIGH-level
input voltage
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
0.9
0.9
1.1
1.3
1.4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.9
0.9
1.1
1.3
1.4
-
-
-
-
-
V
V
V
V
V
V
V
V
V
V
A
-
-
-
-
-
-
-
-
-
VIL
LOW-level
input voltage
0.3
0.4
0.4
0.5
0.6
-
0.3
0.4
0.4
0.5
0.6
0.5
0.3
0.3
0.4
0.5
0.6
1
-
-
-
-
-
-
-
-
II
input leakage select input S;
-
-
current
VI = GND to 4.3 V;
VCC = 1.4 V to 4.3 V
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
5 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
Table 7. Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
Tamb = 25 C
Tamb = 40 C to +125 C Unit
Min
Typ
Max
Min
Max
Max
(85 C) (125 C)
IS(OFF) OFF-state
leakage
nY0 and nY1 port;
see Figure 5
current
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
5
-
-
50
50
500 nA
10
500 nA
IS(ON)
ON-state
leakage
current
nZ port;
VCC = 1.4 V to 3.6 V;
see Figure 6
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
5
-
-
50
50
500 nA
500 nA
10
ICC
supply current VI = VCC or GND;
VSW = GND or VCC
VCC = 3.6 V
-
-
-
-
100
150
-
-
500
800
5000 nA
6000 nA
VCC = 4.3 V
ICC
additional
VSW = GND or VCC
supply current
VI = 2.6 V; VCC = 4.3 V
VI = 2.6 V; VCC = 3.6 V
VI = 1.8 V; VCC = 4.3 V
VI = 1.8 V; VCC = 3.6 V
VI = 1.8 V; VCC = 2.5 V
-
-
-
-
-
-
2.0
0.35
7.0
2.5
50
4.0
0.7
10.0
4.0
200
-
-
-
-
-
-
-
7
1
7
1
A
A
A
A
15
5
15
5
300
-
500 nA
CI
input
1
-
pF
capacitance
CS(OFF) OFF-state
capacitance
supply path switch
data path switch
supply path switch
data path switch
-
-
-
-
35
3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
pF
pF
pF
pF
CS(ON) ON-state
capacitance
130
16
11.1 Test circuits
V
CC
switch
S
1
2
V
IH
S
nY0
nY1
1
2
V
IL
or V
IH
switch
V
IL
I
S
nZ
V
V
O
I
GND
001aam599
VI = 0.3 V or VCC 0.3 V; VO = VCC 0.3 V or 0.3 V.
Fig 5. Test circuit for measuring OFF-state leakage current
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
6 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
V
CC
switch
S
1
2
V
IH
S
nY0
nY1
1
2
V
IL
or V
IH
switch
V
IL
nZ
I
S
V
V
O
I
GND
001aam600
VI = 0.3 V or VCC 0.3 V; VO = VCC 0.3 V or 0.3 V.
Fig 6. Test circuit for measuring ON-state leakage current
11.2 ON resistance
Table 8. ON resistance
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 8 to Figure 13.
Symbol Parameter
Conditions
Tamb = 40 C to +85 C Tamb = 40 C to +125 C Unit
Min Typ[1] Max
Min
Max
Supply path switch
RON
ON resistance VI = GND to VCC;
ISW = 100 mA; see Figure 7
VCC = 1.8 V; VSW = 0 V, 1.8 V
-
-
0.5
0.75
0.7
-
-
0.85
0.8
VCC = 2.7 V; VSW = 0 V, 2.3 V
0.45
[2]
RON
ON resistance VI = GND to VCC; ISW = 100 mA
mismatch
between
channels
VCC = 2.7 V; VSW = 0 V
-
0.1
-
-
-
Data path switches
RON
ON resistance VI = GND to VCC; ISW = 20 mA;
see Figure 7
VCC = 1.8 V; VSW = 0 V, 1.8 V
-
-
7.0
6.0
10.0
9.5
-
-
11.0
10.5
VCC = 2.7 V; VSW = 0 V, 2.3 V
[2]
RON
ON resistance VI = GND to VCC; ISW = 20 mA
mismatch
between
channels
VCC = 2.7 V; VSW = 0 V
-
0.2
-
-
-
[1] Typical values are measured at Tamb = 25 C.
[2] Measured at identical VCC, temperature and input voltage.
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
7 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
11.3 ON resistance test circuit and graphs
001aam602
0.8
R
ON
(Ω)
(1)
0.6
V
SW
V
(2)
0.4
0.2
0
switch
S
V
CC
1
2
V
IL
V
IH
S
nY0
nY1
1
2
V
IL
or V
IH
switch
nZ
V
I
SW
I
GND
0
1
2
3
V (V)
I
001aam601
RON = VSW / ISW
.
(1) VCC = 1.8 V.
(2) CC = 2.7 V.
V
Fig 7. Test circuit for measuring ON resistance
Fig 8. Typical ON resistance as a function of input
voltage (supply path switch)
001aag566
001aag568
1.0
1.0
R
ON
R
ON
(Ω)
(Ω)
0.8
0.8
(1)
(2)
(3)
(4)
0.6
0.4
0.2
0
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
0
1
2
3
0
1
2
3
V (V)
I
V (V)
I
(1) Tamb = 125 C.
(2) Tamb = 85 C.
(3) Tamb = 25 C.
(1) Tamb = 125 C.
(2) Tamb = 85 C.
(3) Tamb = 25 C.
(4)
Tamb = 40 C.
(4) Tamb = 40 C.
Fig 9. ON resistance as a function of input voltage;
VCC = 1.8 V (supply path switch)
Fig 10. ON resistance as a function of input voltage;
VCC = 2.7 V (supply path switch)
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
8 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
001aam603
15
R
ON
(Ω)
13
(1)
11
9
7
(2)
5
0
1
2
3
V (V)
I
(1) VCC = 1.8 V.
(2)
VCC = 2.7 V.
Fig 11. Typical ON resistance as a function of input voltage (data path switch)
001aam604
001aam605
15
10
R
ON
(Ω)
R
ON
(Ω)
(1)
(2)
13
8
6
4
11
9
(3)
(4)
(1)
(2)
(3)
(4)
7
5
0
0.4
0.8
1.2
1.6
2.0
0
1
2
3
V (V)
I
V (V)
I
(1) Tamb = 125 C.
(2) Tamb = 85 C.
(3) Tamb = 25 C.
(1) Tamb = 125 C.
(2) Tamb = 85 C.
(3) Tamb = 25 C.
(4)
Tamb = 40 C.
(4) Tamb = 40 C.
Fig 12. ON resistance as a function of input voltage;
VCC = 1.8 V (data path switch)
Fig 13. ON resistance as a function of input voltage;
VCC = 2.7 V (data path switch)
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
9 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
12. Dynamic characteristics
Table 9.
Dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit see Figure 16.
Symbol Parameter
Conditions
25 C
40 C to +125 C
Unit
Min Typ[1] Max
Min
Max
Max
(85 C) (125 C)
Supply path switch
ten
enable time
S to 1Z or 1Y0, 1Y1;
see Figure 14
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
-
41
30
20
19
19
90
70
45
40
40
-
-
-
-
-
120
80
120
90
ns
ns
ns
ns
ns
50
55
45
45
50
50
tdis
disable time
S to 1Z or 1Y0, 1Y1;
see Figure 14
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
-
-
-
-
-
24
15
9
70
55
25
20
20
-
-
-
-
-
80
60
30
25
25
90
65
35
30
30
ns
ns
ns
ns
ns
8
V
CC = 3.6 V to 4.3 V
8
[2]
tb-m
break-before-make see Figure 15
time
VCC = 1.4 V to 1.6 V
-
-
-
-
-
20
17
13
11
11
-
-
-
-
-
9
7
4
3
2
-
-
-
-
-
-
-
-
-
-
ns
ns
ns
ns
ns
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
Data path switch
ten
enable time
S to nZ or nYn;
see Figure 14
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
-
40
29
20
19
19
90
70
45
40
40
-
-
-
-
-
120
80
120
90
ns
ns
ns
ns
ns
50
55
45
45
50
50
tdis
disable time
S to nZ or nYn;
see Figure 14
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
-
21
13
8
70
55
25
20
20
-
-
-
-
-
80
60
30
25
25
90
65
35
30
30
ns
ns
ns
ns
ns
7
7
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
10 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
Table 9.
Dynamic characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit see Figure 16.
Symbol Parameter
Conditions
25 C
40 C to +125 C
Unit
Min Typ[1] Max
Min
Max
Max
(85 C) (125 C)
[2]
tb-m
break-before-make see Figure 15
time
VCC = 1.4 V to 1.6 V
-
-
-
-
-
23
19
15
13
12
-
-
-
-
-
9
7
4
3
2
-
-
-
-
-
-
-
-
-
-
ns
ns
ns
ns
ns
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
[1] Typical values are measured at Tamb = 25 C and VCC = 1.5 V, 1.8 V, 2.5 V, 3.3 V and 4.3 V respectively.
[2] Break-before-make guaranteed by design.
12.1 Waveform and test circuits
V
I
S input
V
M
t
GND
t
en
dis
V
OH
V
V
X
X
nZ output
OFF to HIGH
HIGH to OFF
nY1 connected to V
EXT
GND
t
t
en
dis
V
OH
V
V
X
X
nZ output
HIGH to OFF
OFF to HIGH
nY0 connected to V
EXT
GND
001aam606
Measurement points are given in Table 10.
Logic level: VOH is typical output voltage level that occurs with the output load.
Fig 14. Enable and disable times
Table 10. Measurement points
Supply voltage
VCC
Input
VM
Output
VX
1.4 V to 4.3 V
0.5VCC
0.9VOH
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
11 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
V
CC
S
nY0
nY1
nZ
G
V
V
R
L
C
L
V
V
= 1.5 V
EXT
I
O
GND
001aam607
a. Test circuit
V
I
0.5V
I
0.9V
O
0.9V
O
V
O
t
b-m
001aag572
b. Input and output measurement points
Fig 15. Test circuit for measuring break-before-make timing
V
CC
S
nY0
nY1
1
2
switch
nZ
G
V
V
R
L
C
L
V
V
= 1.5 V
EXT
I
O
GND
001aam608
Test data is given in Table 11.
Definitions test circuit:
RL = Load resistance.
CL = Load capacitance including jig and probe capacitance.
VEXT = External voltage for measuring switching times.
Fig 16. Test circuit for measuring switching times
Table 11. Test data
Supply voltage
VCC
Input
VI
Load
CL
tr, tf
RL
1.4 V to 4.3 V
VCC
2.5 ns
35 pF
50
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
12 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
12.2 Additional dynamic characteristics
Table 12. Additional dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise
specified); tr = tf 2.5 ns; Tamb = 25 C.
Symbol Parameter
Data path switch
Conditions
Min
Typ
Max
Unit
[1]
[1]
[1]
f(3dB)
3 dB frequency
response
RL = 50 ; see Figure 17
VCC = 2.7 V to 3.6 V
-
-
330
-
-
MHz
dB
iso
isolation (OFF-state)
fi = 10 MHz; RL = 50 ; see Figure 18
VCC = 2.7 V to 3.6 V
60
60
10
Xtalk
crosstalk
between switches;
fi = 10 MHz; RL = 50 ; see Figure 19
VCC = 2.7 V to 3.6 V
-
-
-
-
dB
pC
Qinj
charge injection
fi = 1 MHz; CL = 0.1 nF; RL = 1 M; Vgen = 0 V;
Rgen = 0 ; see Figure 20
VCC = 2.7 V to 3.6 V
[1] fi is biased at 0.5VCC
.
12.3 Test circuits
V
0.5V
CC
CC
switch
S
1
2
V
IL
R
L
S
nY0
nY1
1
2
V
IH
V
IL
or V
IH
switch
nZ
f
i
dB
GND
001aam609
Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads 3 dB.
Fig 17. Test circuit for measuring the frequency response when channel is in ON-state
0.5V
0.5V
CC
CC
switch
S
V
CC
1
2
V
IH
R
L
R
L
V
IL
S
nY0
nY1
1
2
V
IL
or V
IH
switch
nZ
f
dB
i
GND
001aam610
Adjust fi voltage to obtain 0 dBm level at input.
Fig 18. Test circuit for measuring isolation (OFF-state)
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
13 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
0.5V
CC
R
L
CHANNEL
ON
nY0 or nZ
nZ or nY0
f
50 Ω
V
O1
V
i
S
V
IL
0.5V
CC
R
L
nY0 or nZ
nZ or nY0
CHANNEL
OFF
R
50 Ω
i
V
V
O2
001aam611
20 log10 (VO2 / VO1) or 20 log10 (VO1 / VO2).
Fig 19. Test circuit for measuring crosstalk between switches
V
CC
S
nY0
nY1
1
2
switch
nZ
R
gen
G
V
V
R
L
C
L
V
I
O
V
gen
GND
001aam612
a. Test circuit
logic
input
(S) off
on
off
V
O
ΔV
O
001aam613
b. Input and output pulse definitions
Definition: Qinj = VO CL.
VO = output voltage variation.
Rgen = generator resistance.
Vgen = generator voltage.
Fig 20. Test circuit for measuring charge injection
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
14 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
13. Package outline
HXQFN16U: plastic thermal enhanced extremely thin quad flat package; no leads;
16 terminals; UTLP based; body 3 x 3 x 0.5 mm
SOT1039-1
D
B
A
terminal 1
index area
E
A
A
1
detail X
e
1
e
1/2 e
C
M
v
C A
C
B
b
L
1
y
y
M
w
C
1
5
8
L
9
4
1
e
E
e
2
h
1/2 e
12
terminal 1
index area
16
13
X
D
h
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
A
b
D
D
h
E
E
e
e
1
e
2
L
L
v
w
y
y
1
1
h
1
max
0.05 0.35
0.00 0.25
3.1
2.9
1.95
1.75
3.1
2.9
1.95
1.75
0.35
0.25
0.1
0.0
mm
0.5
0.5
1.5
1.5
0.1
0.05 0.05
0.1
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
- - -
JEDEC
JEITA
07-11-14
07-12-01
SOT1039-1
- - -
Fig 21. Package outline SOT1039-1 (HXQFN16U)
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
15 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
XQFN16: plastic, extremely thin quad flat package; no leads;
16 terminals; body 1.80 x 2.60 x 0.50 mm
SOT1161-1
X
D
B
A
E
terminal 1
index area
A
A
1
A
3
detail X
e
1
C
v
C A
C
B
e
b
y
y
w
C
1
5
8
L
4
1
9
e
e
2
12
terminal 1
index area
16
13
L
1
0
1
2 mm
scale
Dimensions
(1)
Unit
A
A
A
b
D
E
e
e
e
2
L
L
1
v
w
y
y
1
1
3
1
max 0.5 0.05
mm nom
min
0.25 1.9 2.7
0.127 0.20 1.8 2.6 0.4 1.2 1.2 0.40 0.50 0.1 0.05 0.05 0.05
0.15 1.7 2.5 0.35 0.45
0.45 0.55
0.00
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
sot1161-1_po
References
Outline
version
European
projection
Issue date
IEC
- - -
JEDEC
- - -
JEITA
- - -
09-12-28
09-12-29
SOT1161-1
Fig 22. Package outline SOT1161-1 (XQFN16)
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
16 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
14. Abbreviations
Table 13. Abbreviations
Acronym
CDM
CMOS
ESD
Description
Charged Device Model
Complementary Metal-Oxide Semiconductor
ElectroStatic Discharge
HBM
MM
Human Body Model
Machine Model
PDA
Personal Digital Assistant
Transistor-Transistor Logic
TTL
15. Revision history
Table 14. Revision history
Document ID
NX3DV2567 v.2
Modifications:
NX3DV2567 v.1
Release date
20111109
Data sheet status
Change notice
Supersedes
Product data sheet
-
NX3DV2567 v.1
• Legal pages updated.
20100928 Product data sheet
-
-
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
17 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
malfunction of an NXP Semiconductors product can reasonably be expected
16.2 Definitions
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
16.3 Disclaimers
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
18 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
NX3DV2567
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 9 November 2011
19 of 20
NX3DV2567
NXP Semiconductors
Low-ohmic four-pole double-throw analog switch
18. Contents
1
2
3
4
5
6
General description. . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3
7
7.1
7.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
8
Functional description . . . . . . . . . . . . . . . . . . . 4
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recommended operating conditions. . . . . . . . 5
9
10
11
Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ON resistance. . . . . . . . . . . . . . . . . . . . . . . . . . 7
ON resistance test circuit and graphs. . . . . . . . 8
11.1
11.2
11.3
12
Dynamic characteristics . . . . . . . . . . . . . . . . . 10
Waveform and test circuits . . . . . . . . . . . . . . . 11
Additional dynamic characteristics . . . . . . . . . 13
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
12.1
12.2
12.3
13
14
15
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 15
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 17
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 17
16
Legal information. . . . . . . . . . . . . . . . . . . . . . . 18
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 18
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16.1
16.2
16.3
16.4
17
18
Contact information. . . . . . . . . . . . . . . . . . . . . 19
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 9 November 2011
Document identifier: NX3DV2567
相关型号:
©2020 ICPDF网 联系我们和版权申明