PCF85116-3TD [NXP]

I2C Demonstration Board 2005-1 Quick Start Guide; I2C演示板2005-1快速入门指南


型号：	PCF85116-3TD
厂家：	NXP
描述：	I2C Demonstration Board 2005-1 Quick Start Guide I2C演示板2005-1快速入门指南
文件：	总12页 (文件大小：268K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

UM10206

I2C Demonstration Board 2005-1 Quick Start Guide

Rev. 01 — 13 June 2006

User manual

Document information

Info

Content

Keywords

Abstract

bidirectional communication, microcontroller, training board

The I2C Demonstration Board 2005-1 is a new expandable low cost I²C

based platform that allows Field Application Engineers, designers and

educators to use their Personal Computer (PC) to easily test and

demonstrate I²C-bus devices from Philips Semiconductors in a platform

similar to a real system environment^.

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

Revision history

Rev

Date

Description

20060613

first release

Contact information

For additional information, please visit: http://www.semiconductors.philips.com

For sales office addresses, please send an email to: sales.addresses@www.semiconductors.philips.com

UM10206

User manual

Rev. 01 — 13 June 2006

2 of 12

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

1. Introduction

The I2C Demonstration Board 2005-1 is a USB based solution that allows engineers and

sales engineers to experiment with general-purpose I²C-bus devices from Philips.

The hardware connects to a standard USB port found on most IBM-compatible PCs and

provides bidirectional communication with I²C-bus devices using the I²C-bus protocol.

The hardware is powered directly from the PC's USB port.

An on-board LED illuminates after the USB host has successfully enumerated it.

The Win-I2CUSB Lite software from The Boardshop runs on Windows 98SE, ME, 2000,

and XP and is compatible with any PC hardware having a minimum of a Pentium

processor and an USB port. The software allows the user to select one of the

I²C-bus devices on the board from a menu and also provides a Universal mode to allow

users to create their own I²C-bus commands with the same I²C-bus devices. The

Win-I2CUSB Lite software is designed to operate only with the specific devices and

device addresses on the I2C Demonstration Board 2005-1.

2. Getting started

2.1 Assumptions

It is helpful to have basic experience with the I²C-bus protocol before using the

demonstration board but it is not absolutely necessary. There are several exercises

targeted at beginners as well as more advanced users. For beginners, the I²C-bus

specification is a good source of detailed information about the I²C-bus. You can

download the complete specification from the Philips Semiconductors website.

2.2 Static Handling Requirements

CAUTION

This device is sensitive to ElectroStatic Discharge (ESD). Therefore care should be taken

during transport and handling. You must use a ground strap or touch the PC case or other

grounded source before unpacking or handling the hardware.

2.3 Minimum System Requirements

• PC Pentium 60 processor (or equivalent), 8MB RAM, 10MB of hard drive space

• one USB port (either 2.0 or 1.1 compatible)

• Windows 98SE, ME, 2000, or XP

2.4 Adapter Power Requirements

The Philips I2C Demonstration Board 2005-1 hardware obtains its power from the PC

USB port.

UM10206

User manual

Rev. 01 — 13 June 2006

3 of 12

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

3. Installation

3.1 Win-I2CUSB Lite Software

1. Download the Win-I2CUSB Lite installation driver from:

www.semiconductors.philips.com/products/interface_control/i2c.

2. The installation software will automatically start from the executable file. If the

installation software does not start automatically double-click on the Setup.exe file.

3. For software or hardware application support email us at: i2c.support@philips.com.

Do not contact The Boardshop for application support issues.

3.2 Demonstration Board hardware connection to computer USB port

1. Touch the bare metal on the rear of your computer to neutralize any ESD (static

charge) before removing the Demonstration Board Hardware from the packaging.

2. Connect the hardware to a USB port using a standard USB cable.

3. The green USB_LINK LED on the hardware will illuminate.

3.3 Connecting the remote sensor diode

1. Connect the red wire to the D+ pin and the white wire to the D− pin (see Figure 1).

2. Plug the remote sensor diode into the Demonstration Board (see Figure 2).

(1)

D+

2N3906

D−

(3)

(2)

013aaa000

(1) The cable is approximately 15cm long with the red wire connected to the emitter.

(2) The 2-pin male connector is compatible with the 2-pin header on the pcb.

(3) The base and collector of the transistor are connected together.

Fig 1. I2C Demonstration Board 2005-1 remote sensor diode

UM10206

User manual

Rev. 01 — 13 June 2006

4 of 12

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

4. Hardware description

Microcontroller

Remote Sensor Diode

USB Port

USB Link Indicator

Expansion Connector

Fig 2. I2C Demonstration Board 2005-1

Figure 2 shows the following items on the hardware:

• USB Port: port where the USB cable is plugged into the board.

• USB_LINK LED: this green LED will illuminate when the cable is connected between

the PC and the hardware.

• remote sensor diode: where the remote sensor diode is plugged into the board to

allow the SA56004E temperature sensor to monitor the ambient temperature.

• microcontroller: a socketed microcontroller is provided to ensure easy service in the

event of damage to the device.

• extension connector: this connector is used to connect future daughter cards targeting

specific Philips Semiconductors I²C-bus devices.

Remark: Philips recommends connecting only daughter cards developed and provided by

Philips Semiconductors to the extension connector. Philips Semiconductors is not

responsible for damage caused by other target cards.

UM10206

User manual

Rev. 01 — 13 June 2006

5 of 12

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

5. I2C Demonstration Board 2005-1 block diagram

MANUAL I²C MASTER

(DIP SWITCHES)

PCA9551

0xC0

SA56004E

PCF8574

0x40

PCA9536

0x82

0x98

Main I²C bus

USB to I²C

CONVERTER

Switched 5.0 V

Switched 3.3 V

5.0 V

PCA9538

0xE4

REGULATOR

3.3 V

RESET

Channel 1

Channel 0

INT0

PCA9540B

PCA9543A

0xE2

PCA9541/01

0xE0

0xFE

INT1

Channel 0

Channel 1

Channel 0

Channel 1

RESET

PCF8563

0xA2

PCF85116

0xA0 to 0xAE

PCA9531

Device 1

0xC8

PCA9531

Device 2

0xC8

SE98

0x30

Fig 3. I2C Demonstration Board 2005-1 block diagram

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

6. I2C Demonstration Board device description

The I²C-bus devices on the I2C Demonstration Board 2005-1 are described in Table 1

I²C-bus devices on the Training Board

Description

8-bit I²C and SMBus I/O port with interrupt

Table 1.

Device

I²C Address

0x40

PCF8574TS

PCA9536D

4-bit I²C and SMBus I/O port

0x82

PCA9540BD

PCF85116-3TD

PCF8563TD

PCA9538D

2-channel I²C-bus multiplexor

2048 x 8-bit CMOS EEPROM with I²C-bus interface

0xE0

0xA0 to 0xAE

real time clock / calendar

8-bit I²C and SMBus low power I/O port with interrupt and 0xE4

reset

0xA2

PCA9551D

8-bit I²C-bus LED driver with programmable blink rates

0xC0

SA56004ED

SMBus compatible, local and remote digital temperature 0x98

sensor with over temperature alarm, accuracy: 1⁰C

PCA9543AD

2 x PCA9531D

PCA9541D/01

2 channel I²C-bus switch with interrupt logic and reset

8-bit I²C-bus LED dimmer

0xE2

0xC8 (both)

0xFE

2-to-1 I²C-bus master selector with interrupt logic and

reset

SE98PW

local only, temperature sensor for SO-DIMM

0x30

UM10206

User manual

Rev. 01 — 13 June 2006

7 of 12

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

7. Starting Win-I2CUSB Lite

When you have correctly installed the software and the Demonstration Board Hardware is

connected and recognized by the computer, start the Win-I2CUSB Lite software (see

Figure 4).

Device selection

(devices not supported in Lite

version are dimmed)

Access to the Expert Mode that allows

writing specific I²C commands

Board Self Test Routine

Hardware detection message

Switched power

indicators

I²C frequency

Fig 4. Win-I2CUSB Lite main window

• When the Demonstration Board hardware is correctly connected to the USB port and

the computer recognizes it, the message “Hardware Detected” is displayed.

• Switched 3.3 V and 5.0 V power supplies are controlled through the “Options” menu

or by double clicking on the 3.3 V or 5.0 V symbols on the lower side of the main

window. Power supplies are disabled by default and you must enable them before

using the I²C-bus devices on the board.

• I²C-bus frequency is controlled through the “Options” menu or by double clicking on

the frequency symbol in the lower side of the main window.

• I²C-bus devices on the board are controlled using the corresponding control window

in the “Device” menu. You can only select I²C-bus devices which are on the board and

are highlighted in the menu.

• The Expert Mode selected through “Device Î Universal Modes” allows you to send

customized I²C-bus commands to any device on the board. Expert Mode is limited to

8 lines of command in the Lite version of the software. Each line of command can

have up to 9 bytes of data.

UM10206

User manual

Rev. 01 — 13 June 2006

8 of 12

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

• The self check routine selected through “Device Î Training Board Self Test” allows a

thorough self test to be performed (device, electrical connection and visual check).

You can save the results of the test in a log file.

8. Upgrades and experimentation

Refer to the UM10207 User Manual for more details on the Win-I2CUSB Lite Software

and programming of different I²C-bus devices.

9. I2C Demonstration Board 2005-1 upgrades

You can purchase a full version of the GUI, called a Win-I2CUSBDLL kit from The

Boardshop (details are available on the website:

www.semiconductors.philips.com/products/interface_control/i2c). The microcontroller

included operates over the entire address range for all devices with a more powerful

universal mode if you need to communicate with devices or addresses not supported by

the Win-I2C Lite software.

The full version of the GUI is incompatible with the Demonstration Board

USB-to-I²C-bus-microcontroller. You can make the GUI work with any Demonstration

Board if you remove the microcontroller from the Win-I2CUSBDLL kit USB based I²C-bus

hardware adapter v2 card and insert it into the microcontroller socket on the

Demonstration Board.

Periodically daughter cards of new devices will become available and new GUIs

generated for these devices. Alternatively existing GUIs will be enhanced based on

operator feedback. The Win-I2CUSB Lite and Win-I2CUSBDLL kit software includes an

automatic update feature which keeps the software updated to most current GUIs.

UM10206

User manual

Rev. 01 — 13 June 2006

9 of 12

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

10. Legal information

Suitability for use — Philips Semiconductors products are not designed,

authorized or warranted to be suitable for use in medical, military, aircraft,

space or life support equipment, nor in applications where failure or

malfunction of a Philips Semiconductors product can reasonably be expected

to result in personal injury, death or severe property or environmental

damage. Philips Semiconductors accepts no liability for inclusion and/or use

of Philips Semiconductors products in such equipment or applications and

therefore such inclusion and/or use is for the customer’s own risk.

10.1 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. Philips Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences of

use of such information.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. Philips Semiconductors makes no

representation or warranty that such applications will be suitable for the

specified use without further testing or modification.

10.2 Disclaimers

General — Information in this document is believed to be accurate and

reliable. However, Philips Semiconductors does not give any representations

or warranties, expressed or implied, as to the accuracy or completeness of

such information and shall have no liability for the consequences of use of

such information.

10.3 Trademarks

Notice: All referenced brands, product names, service names and trademarks

are the property of their respective owners.

Right to make changes — Philips Semiconductors reserves the right to

make changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

I²C-bus — logo is a trademark of Koninklijke Philips Electronics N.V.

UM10206

User manual

Rev. 01 — 13 June 2006

10 of 12

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

Notes

UM10206

User manual

Rev. 01 — 13 June 2006

11 of 12

UM10206

Philips Semiconductors

I2C Demonstration Board 2005-1 Quick Start Guide

11. Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Assumptions. . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Static Handling Requirements . . . . . . . . . . . . . 3

Minimum System Requirements. . . . . . . . . . . . 3

Adapter Power Requirements. . . . . . . . . . . . . . 3

2.1

2.2

2.3

2.4

3.1

3.2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Win-I2CUSB Lite Software . . . . . . . . . . . . . . . . 4

Demonstration Board hardware connection to

computer USB port . . . . . . . . . . . . . . . . . . . . . . 4

Connecting the remote sensor diode . . . . . . . . 4

3.3

Hardware description . . . . . . . . . . . . . . . . . . . . 5

I2C Demonstration Board 2005-1 block

diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

I2C Demonstration Board device description. 7

Starting Win-I2CUSB Lite . . . . . . . . . . . . . . . . . 8

Upgrades and experimentation . . . . . . . . . . . . 9

I2C Demonstration Board 2005-1 upgrades . . 9

Legal information. . . . . . . . . . . . . . . . . . . . . . . 10

Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

10.1

10.2

10.3

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

For more information, please visit: http://www.semiconductors.philips.com.

For sales office addresses, email to: sales.addresses@www.semiconductors.philips.com.

Date of release: 13 June 2006

Document identifier: UM10206

PCF85116-3TD [NXP]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E