PCF8566T,112 [NXP]
PCF8566 - Universal LCD driver for low multiplex rates VSOP 40-Pin;型号: | PCF8566T,112 |
厂家: | NXP |
描述: | PCF8566 - Universal LCD driver for low multiplex rates VSOP 40-Pin PC CD 光电二极管 |
文件: | 总48页 (文件大小:236K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PCF8566
Universal LCD driver for low multiplex rates
Rev. 07 — 25 February 2009
Product data sheet
1. General description
The PCF8566 is a peripheral device which interfaces to almost any Liquid Crystal Display
(LCD) with low multiplex rates. It generates the drive signals for any static or multiplexed
LCD containing up to four backplanes and up to 24 segments and can easily be cascaded
for larger LCD applications. The PCF8566 is compatible with most microprocessors or
microcontrollers and communicates via a two-line bidirectional I2C-bus. Communication
overheads are minimized by a display RAM with auto-incremented addressing, by
hardware subaddressing and by display memory switching (static and duplex drive
modes).
2. Features
I Single-chip LCD controller/driver
I 24 segment drives:
N Up to twelve 7-segment numeric characters including decimal pointer
N Up to six 14-segment alphanumeric characters
N Any graphics of up to 96 elements
I Versatile blinking modes
I No external components required (even in multiple device applications)
I Selectable backplane drive configuration: static or 2, 3, 4 backplane multiplexing
I Selectable display bias configuration: static, 1⁄2 or 1⁄3
I Internal LCD bias generation with voltage-follower buffers
I 24 × 4-bit RAM for display data storage
I Auto-incremented display data loading across device subaddress boundaries
I Display memory bank switching in static and duplex drive modes
I LCD and logic supplies may be separated
I 2.5 V to 6 V power supply range
I Low power consumption
I Power-saving mode for extremely low power consumption in battery-operated and
telephone applications
I I2C-bus interface
I TTL and CMOS compatible
I Compatible with any 4, 8 or 16-bit microprocessor or microcontroller
I May be cascaded for large LCD applications (up to 1536 segments possible)
I Cascadable with 40-segment LCD driver PCF8576C
I Optimized pinning for plane wiring in both and multiple PCF8566 applications
I Space-saving 40-lead plastic very small outline package (VSO40; SOT158-1)
I Manufactured in silicon gate CMOS process
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
3. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
PCF8566P
DIP40
plastic dual in-line package; 40 leads (600 mil)
plastic very small outline package; 40 leads
plastic very small outline package; 40 leads
SOT129-1
SOT158-1
SOT158-1
PCF8566U
PCF8566T
VSO40
VSO40
PCF8566TS[1]
PCF8566U[2]
PCF8566U wire bond die; 40 bonding pads;
2.5 × 2.91 × 0.381 mm
[1] Dark-green version.
[2] Chip in tray for chip on board.
4. Marking
Table 2.
Marking codes
Type number
PCF8566P
PCF8566T
PCF8566TS
PCF8566U
Marking code
PCF8566P
PCF8566T
PCF8566TS
PC8566-1
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
2 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
5. Block diagram
BP0 BP2 BP1 BP3
13 14 15 16
S0 to S23
17 to 40
5
V
DD
BACKPLANE
OUTPUTS
DISPLAY SEGMENT OUTPUTS
R
R
R
LCD
VOLTAGE
SELECTOR
DISPLAY LATCH
SHIFT REGISTER
LCD BIAS
GENERATOR
12
V
LCD
PCF8566
4
3
DISPLAY
RAM
24 × 4 BITS
CLK
INPUT
BANK
SELECTOR
OUTPUT
BANK
SELECTOR
TIMING
BLINKER
SYNC
DISPLAY
CONTROLLER
6
OSC
OSCILLATOR
POWER-
ON
DATA
POINTER
RESET
COMMAND
DECODER
11
V
SS
2
1
SUB-
ADDRESS
COUNTER
SCL
SDA
2
INPUT
FILTERS
I C-BUS
CONTROLLER
10
7
8
9
SA0
A0 A1 A2
mgg383
Fig 1. Block diagram of PCF8566
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
3 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
6. Pinning information
6.1 Pinning
1
2
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
SDA
SCL
S23
S22
S21
S20
S19
S18
S17
S16
S15
S14
S13
S12
S11
S10
S9
3
SYNC
CLK
4
V
DD
5
6
OSC
A0
7
8
A1
9
A2
10
11
12
13
14
15
16
17
18
19
20
SA0
PCF8566
V
SS
V
LCD
BP0
BP2
BP1
BP3
S0
S8
S7
S1
S6
S2
S5
S3
S4
001aai338
Fig 2. Pin configuration for PCF8566
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
4 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
25 24 23 22 21
20 19 18 17 16
15
14
13
12
BP1
BP2
BP0
26
S9
S10
S11
27
28
29
30
31
32
33
34
35
V
LCD
S12
V
11
10
9
S13
S14
S15
S16
S17
SS
PCF8566U
SA0
A2
8
A1
7
A0
6
OSC
S18
36 37 38 39 40
1
2
3
4
5
mbh783
Fig 3. Pin configuration for PCF8566U
6.2 Pin description
Table 3.
Pin description
Symbol
SDA
SCL
SYNC
CLK
VDD
Pin
1
Description
I2C-bus data input and output
I2C-bus clock input and output
2
3
cascade synchronization input and output
external clock input and output
positive supply voltage[1]
4
5
OSC
A0
6
oscillator select
I2C-bus subaddress inputs
7
A1
8
A2
9
SA0
VSS
10
11
12
I2C-bus slave address bit 0 input
logic ground
VLCD
LCD supply voltage
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
5 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Table 3.
Pin description …continued
Symbol
BP0
Pin
13
Description
LCD backplane outputs
BP2
14
BP1
15
BP3
16
S0 to S23
17 to 40
LCD segment outputs
[1] The substrate (rear side of the die) is wired to VDD but should not be electrically connected.
7. Functional description
The PCF8566 is a versatile peripheral device designed to interface any
microprocessor or microcontroller to a wide variety of LCDs. It can directly drive any static
or multiplexed LCD containing up to 4 backplanes and up to 24 segments.
The display configurations possible with the PCF8566 depend on the number of active
backplane outputs required. Display configuration selection is shown in Table 4. All of the
display configurations given in Table 4 can be implemented in the typical system shown in
Figure 4.
The host microprocessor or microcontroller maintains the 2-line I2C-bus communication
channel with the PCF8566.
Biasing voltages for the multiplexed LCD waveforms are generated internally, removing
the need for an external bias generator. The internal oscillator is selected by connecting
pin OSC to VSS. The only other connections required to complete the system are the
power supplies (pins VDD, VSS and VLCD) and the LCD panel selected for the application.
Table 4.
Display configurations
7-segment numeric
Backplanes Elements
14-segment numeric
Dot matrix
Digits
Indicator
symbols
Characters Indicator
symbols
4
3
2
1
96
72
48
24
12
9
12
9
6
4
3
1
12
16
6
96 (4 × 24)
72 (3 × 24)
48 (2 × 24)
24
6
6
3
3
10
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
6 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
V
DD
t
rise
R ≤
2 C
bus
V
V
LCD
DD
5
12
SDA
HOST
MICRO-
1
2
6
17 to 40 24 segment drives
LCD PANEL
SCL
PCF8566
PROCESSOR/
MICRO-
CONTROLLER
(up to 96
elements)
OSC
4 backplanes
13 to 16
10 11
7
8
9
mgg385
A0 A1 A2 SA0 V
SS
V
SS
Fig 4. Typical system configuration
7.1 Power-on reset
At power-on the PCF8566 resets to the following starting conditions:
• All backplane outputs are set to VDD
• All segment outputs are set to VDD
• Drive mode 1:4 multiplex with 1⁄3 bias is selected
• Blinking is switched off
• Input and output bank selectors are reset (as defined in Table 8)
• The I2C-bus interface is initialized
• The data pointer and the subaddress counter are cleared
Do not transfer data on the I2C-bus after a power-on for at least 1 ms to allow the reset
action to complete.
7.2 LCD bias generator
The full-scale LCD voltage (Voper) is obtained from VDD − VLCD. The LCD voltage may be
temperature compensated externally through the VLCD supply to pin 12.
Fractional LCD biasing voltages are obtained from an internal voltage divider comprising
three series resistors connected between VDD and VLCD. The center resistor can be
switched out of the circuit to provide a 1⁄2 bias voltage level for the 1:2 multiplex
configuration.
7.3 LCD voltage selector
The LCD voltage selector coordinates the multiplexing of the LCD in accordance with the
selected LCD drive configuration. The operation of the voltage selector is controlled by
mode-set commands from the command decoder. The biasing configurations that apply to
the preferred modes of operation, together with the biasing characteristics as functions of
VLCD and the resulting discrimination ratios (D), are given in Table 5.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
7 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Table 5.
Preferred LCD drive modes: summary of characteristics
LCD drive mode Number of:
LCD bias
configuration
V off (RMS)
V on(RMS)
V on(RMS)
--------------------------
V LCD
D = --------------------------
V off (RMS)
------------------------
V LCD
Backplanes Bias levels
static
1
2
2
3
4
2
3
4
4
4
static
0
1
∞
1
⁄
1:2 multiplex
1:2 multiplex
1:3 multiplex
1:4 multiplex
0.354
0.333
0.333
0.333
0.791
0.745
0.638
0.577
2.236
2.236
1.915
1.732
2
1
⁄
3
1
⁄
3
1
⁄
3
A practical value for VLCD is determined by equating Voff(RMS) with a defined LCD
threshold voltage (Vth), typically when the LCD exhibits approximately 10 % contrast. In
the static drive mode a suitable choice is VLCD > 3Vth.
Multiplex drive modes of 1:3 and 1:4 with 1⁄2 bias are possible but the discrimination and
hence the contrast ratios are smaller.
1
Bias is calculated by ------------ , where the values for a are
1 + a
a = 1 for 1⁄2 bias
a = 2 for 1⁄3 bias
The RMS on-state voltage (Von(RMS)) for the LCD is calculated with the equation
2
1
n
1
-- + (n – 1) ×
------------
1 + a
V
LCD
Von(RMS)
=
------------------------------------------------------------
(1)
n
where VLCD is the resultant voltage at the LCD segment and where the values for n are
n = 1 for static mode
n = 2 for 1:2 multiplex
n = 3 for 1:3 multiplex
n = 4 for 1:4 multiplex
The RMS off-state voltage (Voff(RMS)) for the LCD is calculated with the equation:
a2 – (2a + n)
n × (1 + a)2
V
Voff (RMS)
=
--------------------------------
(2)
(3)
LCD
Discrimination is the ratio of Von(RMS) to Voff(RMS) and is determined from the equation:
(a + 1)2 + (n – 1)
Von(RMS)
=
-------------------------------------------
------------------------
(a – 1)2 + (n – 1)
V off (RMS)
Using Equation 3, the discrimination for an LCD drive mode of
• 1:3 multiplex with 1⁄2 bias is 3 = 1.732
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
8 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
21
• 1:4 multiplex with 1⁄2 bias is ---------- = 1.528
3
The advantage of these LCD drive modes is a reduction of the LCD full scale voltage VLCD
as follows:
• 1:3 multiplex (1⁄2 bias): V LCD
=
6 × V off (RMS) = 2.449V off (RMS)
(4 × 3)
• 1:4 multiplex (1⁄2 bias): V LCD
=
= 2.309V off (RMS)
---------------------
3
These compare with V LCD = 3V off (RMS) when 1⁄3 bias is used.
It should be noted that VLCD is sometimes referred as the LCD operating voltage.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
9 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
7.4 LCD drive mode waveforms
7.4.1 Static drive mode
The static LCD drive mode is used when a single backplane is provided in the LCD.
Backplane and segment drive waveforms for this mode are shown in Figure 5.
T
fr
LCD segments
V
LCD
BP0
Sn
V
SS
state 1
(on)
state 2
(off)
V
LCD
V
SS
V
LCD
Sn+1
V
SS
(a) Waveforms at driver.
V
LCD
state 1
0 V
−V
LCD
V
LCD
state 2
0 V
−V
LCD
(b) Resultant waveforms
at LCD segment.
mgl745
Vstate1(t) = VSn(t) − VBP0(t).
Von(RMS) = VLCD
.
Vstate2(t) = VSn+1(t) − VBP0(t).
Voff(RMS) = 0 V.
Fig 5. Static drive mode waveforms
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
10 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
7.4.2 1:2 Multiplex drive mode
When two backplanes are provided in the LCD, the 1:2 multiplex mode applies. The
PCF8566 allows the use of 1⁄2 bias or 1⁄3 bias (see Figure 6 and Figure 7).
T
fr
V
LCD
LCD segments
V
V
/ 2
/ 2
BP0
BP1
Sn
LCD
SS
state 1
state 2
V
LCD
V
V
LCD
SS
V
LCD
V
V
SS
LCD
Sn+1
V
SS
(a) Waveforms at driver.
V
V
LCD
/ 2
LCD
0 V
−V
state 1
/ 2
LCD
−V
LCD
V
V
LCD
/ 2
LCD
0 V
state 2
−V
/ 2
LCD
LCD
−V
(b) Resultant waveforms
at LCD segment.
mgl746
Vstate1(t) = VSn(t) − VBP0(t).
Von(RMS) = 0.791VLCD
.
Vstate2(t) = VSn(t) − VBP1(t).
Voff(RMS) = 0.354VLCD
Fig 6. Waveforms for the 1:2 multiplex drive mode with 1⁄2 bias
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
11 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
T
fr
V
LCD
2V
LCD segments
/ 3
LCD
/ 3
BP0
BP1
Sn
V
V
LCD
SS
state 1
state 2
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
Sn+1
V
V
LCD
SS
(a) Waveforms at driver.
V
LCD
2V
/ 3
LCD
/ 3
V
LCD
0 V
−V
state 1
/ 3
LCD
−2V
/ 3
LCD
−V
LCD
V
LCD
2V
/ 3
/ 3
LCD
V
LCD
0 V
−V
state 2
/ 3
LCD
−2V
/ 3
LCD
−V
LCD
(b) Resultant waveforms
at LCD segment.
mgl747
Vstate1(t) = VSn(t) − VBP0(t).
Von(RMS) = 0.745VLCD
Vstate2(t) = VSn(t) − VBP1(t)
Voff(RMS) = 0.333VLCD.
Fig 7. Waveforms for the 1:2 multiplex drive mode with 1⁄3 bias
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
12 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
7.4.3 1:3 Multiplex drive mode
When three backplanes are provided in the LCD, the 1:3 multiplex drive mode applies as
shown in Figure 8.
T
fr
V
LCD
2V
LCD segments
/ 3
LCD
/ 3
BP0
BP1
BP2
Sn
V
V
LCD
SS
state 1
state 2
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
Sn+1
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
Sn+2
V
V
LCD
SS
(a) Waveforms at driver.
V
LCD
2V
/ 3
LCD
/ 3
V
LCD
0 V
−V
state 1
/ 3
LCD
−2V
/ 3
LCD
−V
LCD
V
LCD
2V
/ 3
/ 3
LCD
V
LCD
0 V
−V
state 2
/ 3
LCD
−2V
/ 3
LCD
−V
LCD
(b) Resultant waveforms
at LCD segment.
mgl748
Vstate1(t) = VSn(t) − VBP0(t).
Von(RMS) = 0.638VLCD
.
Vstate2(t) = VSn(t) − VBP1(t).
Voff(RMS) = 0.333VLCD.
Fig 8. Waveforms for the 1:3 multiplex drive mode with 1⁄3 bias
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
13 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
7.4.4 1:4 multiplex drive mode
When four backplanes are provided in the LCD, the 1:4 multiplex drive mode applies, as
shown in Figure 9.
T
fr
V
LCD segments
LCD
2V
/ 3
LCD
/ 3
BP0
BP1
BP2
V
V
LCD
SS
state 1
state 2
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
BP3
Sn
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
Sn+1
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
Sn+2
Sn+3
V
V
LCD
SS
V
LCD
2V
/ 3
LCD
/ 3
V
V
LCD
SS
(a) Waveforms at driver.
V
LCD
2V
/ 3
LCD
/ 3
V
LCD
0 V
−V
state 1
/ 3
LCD
−2V
/ 3
LCD
−V
LCD
V
LCD
2V
/ 3
/ 3
LCD
V
LCD
0 V
−V
state 2
/ 3
LCD
−2V
/ 3
LCD
−V
LCD
(b) Resultant waveforms
at LCD segment.
mgl749
Vstate1(t) = VSn(t) − VBP0(t).
Von(RMS) = 0.577VLCD
.
Vstate2(t) = VSn(t) − VBP1(t).
Voff(RMS) = 0.333VLCD.
Fig 9. Waveforms for the 1:4 multiplex mode with 1⁄3 bias
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
14 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
7.5 Oscillator
The internal logic and the LCD drive signals of the PCF8566 are timed by the frequency
fclk, which equals either the built-in oscillator frequency fosc or the external clock frequency
fclk(ext)
.
The clock frequency (fclk) determines the LCD frame frequency (ffr) and the maximum rate
for data reception from the I2C-bus. To allow I2C-bus transmissions at their maximum data
rate of 100 kHz, fclk should be chosen to be above 125 kHz.
7.5.1 Internal clock
The internal oscillator is enabled by connecting pin OSC to pin VSS. In this case, the
output from pin CLK is the clock signal for any cascaded PCF8566s or PCF8576s in the
system.
7.5.2 External clock
Connecting pin OSC to VDD enables an external clock source. Pin CLK then becomes the
external clock input.
Remark: A clock signal must always be supplied to the device. Removing the clock,
freezes the LCD in a DC state.
7.6 Timing
The timing of the PCF8566 sequences the internal data flow of the device. This includes
the transfer of display data from the display RAM to the display segment outputs. In
cascaded applications, the synchronization signal (SYNC) maintains the correct timing
relationship between the PCF8566s in the system. The timing also generates the LCD
frame frequency which is derived as an integer division of the clock frequency (see
Table 6). The frame frequency is set by the mode set commands when an internal clock is
used or by the frequency applied to the pin CLK when an external clock is used.
Table 6.
LCD frame frequencies [1]
PCF8566 mode
Frame frequency
Nominal frame frequency (Hz)
normal mode
69 [2]
f clk
f fr
=
=
------------
2880
power saving mode
65 [3]
f clk
f fr
---------
480
[1] The possible values for fclk see Table 20.
[2] For fclk = 200 kHz.
[3] For fclk = 31 kHz.
The ratio between the clock frequency and the LCD frame frequency depends on the
mode in which the device is operating. In the power-saving mode the reduction ratio is six
times smaller; this allows the clock frequency to be reduced by a factor of six. The
reduced clock frequency results in a significant reduction in power dissipation.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
15 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
The lower clock frequency has the disadvantage of increasing the response time when
large amounts of display data are transmitted on the I2C-bus. When a device is unable to
process a display data byte before the next one arrives, it holds the SCL line LOW until the
first display data byte is stored. This slows down the transmission rate of the I2C-bus but
no data loss occurs.
7.7 Display register
The display register holds the display data while the corresponding multiplex signals are
generated. There is a one-to-one relationship between the data in the display register, the
LCD segment outputs and one column of the display RAM.
7.8 Shift register
The shift register transfers display information from the display RAM to the display register
while previous data is displayed.
7.9 Segment outputs
The LCD drive section includes 24 segment outputs S0 to S23 which must be connected
directly to the LCD. The segment output signals are generated based on the multiplexed
backplane signals and with data resident in the display register. When less than
24 segment outputs are required, the unused segment outputs should be left open-circuit.
7.10 Backplane outputs
The LCD drive section includes four backplane outputs: BP0 to BP3. The backplane
output signals are generated based on the selected LCD drive mode.
• In 1:4 multiplex drive mode: BP0 to BP3 must be connected directly to the LCD.
If less than four backplane outputs are required the unused outputs can be left as an
open-circuit.
• In 1:3 multiplex drive mode: BP3 carries the same signal as BP1, therefore these two
adjacent outputs can be tied together to give enhanced drive capabilities.
• In 1:2 multiplex drive mode: BP0 and BP2, BP1 and BP3 respectively carry the same
signals and can also be paired to increase the drive capabilities.
• In static drive mode: the same signal is carried by all four backplane outputs and they
can be connected in parallel for very high drive requirements.
7.11 Display RAM
The display RAM is a static 24 × 4-bit RAM which stores LCD data. Logic 1 in the RAM bit
map indicates the on-state of the corresponding LCD segment; similarly, logic 0 indicates
the off-state. There is a direct relationship between the RAM addresses and the segment
outputs, and between the individual bits of a RAM word and the backplane outputs. The
first RAM row corresponds to the 24 segments operated with respect to backplane BP0
(see Figure 10). In multiplexed LCD applications, the segment data of rows 1 to 4 of the
display RAM are time-multiplexed with BP0, BP1, BP2 and BP3 respectively.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
16 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
display RAM addresses (columns)/segment outputs (S)
0
1
2
3
4
19 20 21 22 23
0
1
2
3
display RAM bits
(rows)/
backplane outputs
(BP)
mgg389
Fig 10. Display RAM bit map showing the direct relationship between display RAM
addresses and segment outputs and between bits in a RAM word and backplane
outputs
When display data is transmitted to the PCF8566 the display bytes received are stored in
the display RAM based on the selected LCD drive mode. An example of a 7-segment
numeric display illustrating the storage order for all drive modes is shown in Figure 11.
The RAM storage organization applies equally to other LCD types.
The following applies to Figure 11:
• Static drive mode: the eight transmitted data bits are placed in row 0 to eight
successive display RAM addresses.
• 1:2 multiplex drive mode: the eight transmitted data bits are placed in row 0 and 1 to
four successive display RAM addresses.
• 1:3 multiplex drive mode: the eight transmitted data bits are placed in row 0, 1 and 2 of
three successive addresses, with bit 2 of the third address left unchanged. This last bit
can, if necessary, be controlled by an additional transfer to this address but avoid
overriding adjacent data because always full bytes are transmitted.
• 1:4 multiplex drive mode: the eight transmitted data bits are placed in row 0, 1, 2 and
3 to two successive display RAM addresses.
7.12 Data pointer
The addressing mechanism for the display RAM is realized using the data pointer. This
allows the loading of an individual display data byte or a series of display data bytes, into
any location of the display RAM. The sequence commences with the initialization of the
data pointer by the load data pointer command (see Table 13). After this, the data byte is
stored starting at the display RAM address indicated by the data pointer (see Figure 11).
Once each byte is stored, the data pointer is automatically incremented based on the
selected LCD configuration.
The contents of the data pointer are incremented as follows:
• In static drive mode by eight.
• In 1:2 multiplex drive mode by four.
• In 1:3 multiplex drive mode by three.
• In 1:4 multiplex drive mode by two.
If an I2C-bus data access terminates early, the state of the data pointer is unknown.
Consequently, the data pointer must be rewritten prior to further RAM accesses.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
17 of 48
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
drive mode
LCD segments
a
LCD backplanes
display RAM filling order
transmitted display byte
S
n+2
n
n
1
n
2
n
3
n
4
n
5
n
6
n 7
b
BP0
f
S
S
n+3
n+1
MSB
LSB
0
1
2
3
c
x
x
x
b
x
x
x
a
x
x
x
f
g
x
x
x
e
x
x
x
d
x
x
x
DP
bit/
BP
g
S
n+4
S
n
x
x
x
x
x
x
c
b
a
f
g
e
d
DP
static
e
S
S
S
n+5
n+7
DP
c
d
n+6
BP0
S
n
a
n
n
n
n
1
1
1
n
2
n 3
b
b
b
1:2
f
S
n+1
MSB
LSB
DP
0
1
2
3
a
b
x
x
f
e
c
x
x
d
bit/
BP
g
g
x
x
DP
x
x
a
b
f
g
e c d
BP1
multiplex
S
S
e
n+2
n+3
c
c
c
d
d
d
DP
BP0
BP1
S
n+1
a
n
n 2
S
S
n
f
1:3
n+2
MSB
LSB
e
0
1
2
3
b
DP
c
a
d
g
x
f
bit/
BP
g
e
x
x
BP2
multiplex
b
DP
c
a
d
g
f
e
x
DP
S
n
a
n
BP2
BP3
BP0
BP1
f
1:4
0
1
2
3
a
c
f
bit/
BP
MSB
LSB
d
g
e
g
d
multiplex
b
DP
e
a
c
b
DP
f
e
g
S
n+1
DP
mgl751
x = data bit unchanged
Fig 11. Relationship between LCD layout, drive mode, display RAM filling order and display data transmitted over the I2C-bus
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
7.13 Sub-address counter
The storage of display data is conditioned by the contents of the subaddress counter.
Storage is allowed to take place only when the contents of the subaddress counter match
with the hardware subaddress applied to A0, A1 and A2. The subaddress counter value is
defined by the device select command (see Table 14 and Table 21). If the contents of the
subaddress counter and the hardware subaddress do not match then data storage is
blocked but the data pointer will be incremented as if data storage had taken place. The
subaddress counter is also incremented when the data pointer overflows.
The storage arrangements described lead to extremely efficient data loading in cascaded
applications. When a series of display bytes are sent to the display RAM, automatic
wrap-over to the next PCF8566 occurs when the last RAM address is exceeded.
Subaddressing across device boundaries is successful even if the change to the next
device in the cascade occurs within a transmitted character (such as during the 14th
display data byte transmitted in 1:3 multiplex mode).
7.14 Output bank selector
The output bank selector (see Table 15), selects one of the four bits per display RAM
address for transfer to the display register. The actual bit selected depends on the LCD
drive mode in operation and on the instant in the multiplex sequence.
• In 1:4 multiplex mode: all RAM addresses of bit 0 are selected, followed sequentially
by the contents of bit 1, bit 2 and then bit 3.
• In 1:3 multiplex mode: bits 0, 1 and 2 are selected sequentially.
• In 1:2 multiplex mode: bits 0 and 1 are selected.
• In the static mode: bit 0 is selected.
The PCF8566 includes a RAM bank switching feature in the static and 1:2 multiplex drive
modes. In the static drive mode, the bank select command may request the contents of
bit 2 to be selected for display instead of the contents of bit 0. In 1:2 multiplex drive mode,
the contents of bits 2 and 3 may be selected instead of bits 0 and 1. This enables
preparation of display information in an alternative bank and the ability to switch to it once
it has been assembled.
7.15 Input bank selector
The input bank selector loads display data into the display RAM based on the selected
LCD drive configuration. Using the bank select command, display data can be loaded in
bit 2 into static drive mode or in bits 2 and 3 into 1:2 multiplex drive mode. The input bank
selector functions independently of the output bank selector.
7.16 Blinker
The display blinking capabilities of the PCF8566 are very versatile. The whole display can
be blinked at frequencies selected by the blink command. The blinking frequencies are
integer fractions of the clock frequency; the ratios between the clock and blinking
frequencies depend on the mode in which the device is operating (see Table 7).
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
19 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Table 7.
Blink frequencies
Blinking mode
Normal operating
mode ratio
Power saving mode
ratio
Blink frequency
off
1
-
-
blinking off
2 Hz
f clk
f elk
f blink
f blink
f blink
=
=
=
f blink
f blink
f blink
=
=
=
----------------
92160
----------------
15360
2
3
1 Hz
f clk
f clk
-------------------
184320
----------------
30720
0.5 Hz
f clk
f clk
-------------------
368640
----------------
61440
An additional feature is for an arbitrary selection of LCD segments to be blinked. This
applies to the static and 1:2 multiplex drive modes and can be implemented without any
communication overheads. Using the output bank selector, the displayed RAM banks are
exchanged with alternate RAM banks at the blinking frequency. This mode can also be
specified by the blink select command.
In the 1:3 and 1:4 multiplex modes, where no alternate RAM bank is available, groups of
LCD segments can be blinked by selectively changing the display RAM data at fixed time
intervals.
If the entire display needs to be blinked at a frequency other than the nominal blinking
frequency, this can be done using the mode set command to set and reset the display
enable bit E at the required rate (see Table 9).
8. Basic architecture
8.1 Characteristics of the I2C-bus
The I2C-bus provides bidirectional, two-line communication between different IC or
modules. The two lines are a Serial Data line (SDA) and a Serial Clock Line (SCL). When
connected to the output stages of a device, both lines must be connected to a positive
supply via a pull-up resistor. Data transfer is initiated only when the bus is not busy.
8.1.1 Bit transfer
One data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the HIGH period of the clock pulse. Changes in the data line at this time will
be interpreted as a control signal. Bit transfer is illustrated in Figure 12.
SDA
SCL
data line
stable;
data valid
change
of data
allowed
mba607
Fig 12. Bit transfer
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
20 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
8.1.1.1 START and STOP conditions
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW change
of the data line, while the clock is HIGH, is defined as the START condition (S).
A LOW-to-HIGH change of the data line, while the clock is HIGH, is defined as the STOP
condition (P). The START and STOP conditions are illustrated in Figure 13.
SDA
SCL
SDA
SCL
S
P
START condition
STOP condition
mbc622
Fig 13. Definition of START and STOP conditions
8.1.2 System configuration
A device generating a message is a transmitter and a device receiving a message is the
receiver. The device that controls the message is the master and the devices which are
controlled by the master are the slaves. The system configuration is illustrated in
Figure 14.
MASTER
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER/
RECEIVER
SLAVE
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
MASTER
TRANSMITTER
SDA
SCL
mga807
Fig 14. System configuration
8.1.3 Acknowledge
The number of data bytes transferred between the START and STOP conditions from
transmitter to receiver is unlimited. Each byte of eight bits is followed by an acknowledge
bit. The acknowledge bit is a HIGH level signal put on the bus by the transmitter during
which time the master generates an extra acknowledge related clock pulse. (See
Figure 15).
Acknowledgement on the I2C-bus is illustrated in
• A slave receiver which is addressed must generate an acknowledge after the
reception of each byte.
• A master receiver must generate an acknowledge after the reception of each byte that
has been clocked out of the slave transmitter.
• The device that acknowledges must pull-down the SDA line during the acknowledge
clock pulse, so that the SDA line is stable LOW during the HIGH period of the
acknowledge related clock pulse (set-up and hold times must be taken into
consideration).
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
21 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
• A master receiver must signal an end-of-data to the transmitter by not generating an
acknowledge on the last byte that has been clocked out of the slave. In this event, the
master receiver must leave the data line HIGH during the 9th pulse to not
acknowledge. The master will now generate a STOP condition.
data output
by transmitter
not acknowledge
data output
by receiver
acknowledge
SCL from
master
1
2
8
9
S
clock pulse for
acknowledgement
START
condition
mbc602
Fig 15. Acknowledgement on the I2C-bus
8.1.4 PCF8566 I2C-bus controller
The PCF8566 acts as an I2C-bus slave receiver. It does not initiate I2C-bus transfers or
transmit data to an I2C-bus master receiver. The only data output from the PCF8566 are
the acknowledge signals of the selected devices. Device selection depends on the
I2C-bus slave address, the transferred command data and the hardware subaddress.
In single device application, the hardware subaddress inputs A0, A1 and A2 are normally
tied to VSS which defines the hardware subaddress 0. In multiple device applications
A0, A1 and A2 are tied to VSS or VDD using a binary coding scheme so that no two
devices with a common I2C-bus slave address have the same hardware subaddress.
In the power-saving mode it is possible that the PCF8566 is not able to keep up with the
highest transmission rates when large amounts of display data are transmitted. If this
situation occurs, the PCF8566 forces the SCL line LOW until its internal operations are
completed. This is known as the clock synchronization feature of the I2C-bus and serves
to slow down fast transmitters. Data loss does not occur.
8.1.5 Input filter
To enhance noise immunity in electrically adverse environments, RC low-pass filters are
provided on the SDA and SCL lines.
8.2 I2C-bus protocol
Two I2C-bus 7 bit slave addresses (0111 110 and 0111 111) are reserved for the
PCF8566. The least significant bit after the slave address is bit R/W. The PCF8566 is a
write-only device. It will not respond to a read access, so this bit should always be logic 0.
The second bit of the slave address is defined by the level tied at input SA0.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
22 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
R/W
slave address
S
A
0
0
1
1
1
1
1
0
1 byte
001aai455
Fig 16. Slave address structure
Two displays controlled by PCF8566 can be recognized on the same I2C-bus which
allows:
• Up to 16 PCF8566s on the same I2C-bus for very large LCD applications (see
Section 13)
• The use of two types of LCD multiplex on the same I2C-bus
The I2C-bus protocol is shown in Figure 17. The sequence is initiated with a START
condition (S) from the I2C-bus master which is followed by one of the PCF8566 slave
addresses. All PCF8566s with the same SA0 level acknowledge in parallel to the slave
address. All PCF8566s with the alternative SA0 level ignore the whole I2C-bus transfer.
After acknowledgement, one or more command bytes (m) follow which define the status of
the addressed PCF8566s. The last command byte is tagged with a cleared most
significant bit, the continuation bit C. The command bytes are also acknowledged by all
addressed PCF8566s on the bus.
After the last command byte, a series of display data bytes (n) may follow. These display
bytes are stored in the display RAM at the address specified by the data pointer and the
subaddress counter. Both data pointer and subaddress counter are automatically updated
and the data is directed to the intended PCF8566 device.
The acknowledgement after each byte is made only by the (A0, A1 and A2) addressed
PCF8566. After the last display byte, the I2C-bus master issues a STOP condition (P).
acknowledge
acknowledge by
by A0, A1 and A2
all addressed
selected
PCF8566 only
R/W
0
PCF8566s
slave address
S
A
0
S
0
1
1
1
1
1
A C
A
DISPLAY DATA
n > 0 byte(s)
A P
COMMAND
1 byte
m ≥ 1 byte(s)
update data pointers
and if necessary,
subaddress counter
mgg390
Fig 17. I2C-bus protocol
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
23 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
8.3 Command decoder
The command decoder identifies command bytes that arrive on the I2C-bus. All available
commands carry a continuation bit C in their most significant bit position as shown in
Figure 18. When this bit is set, it indicates that the next byte of the transfer to arrive will
also represent a command. If this bit is reset, it indicates that the command byte is the last
in the transfer. Further bytes will be regarded as display data.
The five commands available to the PCF8566 are defined in Table 8.
MSB
LSB
C
REST OF OPCODE
msa833
(1) C = 0; last command.
(2) C = 1; commands continue.
Fig 18. General format of byte command
Table 8.
Definition of PCF8566 commands
Command
Opcode
Reference
Description
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Mode set
C
1
0
LP
E
B
M1
M0
Section 8.3.1 defines LCD drive mode, LCD bias
configuration, display status and
power dissipation mode
Load data
pointer
C
C
C
0
1
1
0
1
1
P4
0
P3
0
P2
A2
0
P1
A1
I
P0
A0
O
Section 8.3.2 data pointer to define one of 24
display RAM addresses
Device select
Section 8.3.3 define one of eight hardware
subaddresses
Bank select
1
1
Section 8.3.4 bit I: defines input bank selection
(storage of arriving display data);
bit O: defines output bank selection
(retrieval of LCD display data)
Blink
C
1
1
1
0
A
BF1 BF0 Section 8.3.5 defines the blink frequency and blink
mode
8.3.1 Mode set command
Table 9.
LCD drive mode command bit description
LCD drive mode
Bit
M1
0
Drive mode
Backplane
BP0
M0
1
static
1:2
BP0, BP1
1
0
1:3
BP0, BP1. BP2
BP0, BP1. BP2, BP3
1
1
1:4
0
0
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
24 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Table 10. LCD bias configuration command bit description
LCD bias
Bit B
1⁄3 bias
1⁄2 bias
0
1
Table 11. Display status command bit description[1]
Display status
disabled (blank)
enabled
Bit E
0
1
[1] The possibility to disable the display allows implementation of blinking under external control.
Table 12. Power dissipation mode command bit description
Display status
normal mode
Bit LP
0
1
power saving mode
8.3.2 Load data pointer command
Table 13. Load data pointer command bit description
Description
Bit
5 bit binary value, 0 to 23
P4
P3
P2
P1
P0
8.3.3 Device select command
Table 14. Device select command bit description
Description
Bit
3 bit binary value, 0 to 7
A2
A1
A0
8.3.4 Bank select command
Table 15. Bank select command[1]
Bank
Mode
Static
Bit
I
Value
1:2 MUX
Input bank
RAM bit 0
RAM bit 2
RAM bits 0 and 1
RAM bits 2 and 3
0
1
Output bank
RAM bit 0
RAM bit 2
RAM bits 0 and 1
RAM bits 2 and 3
O
0
1
[1] The bank select command has no effect in 1:3 or 1:4 multiplex drive modes.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
25 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
8.3.5 Blink command
Table 16. Blink frequency command bit description
Blink frequency
Bit
BF1
0
BF0
0
off
1
0
1
2
1
0
3
1
1
Table 17. Blink mode command bit description
Blink mode
Bit A
Normal blinking
0
1
Alternate RAM bank blinking
8.4 Display controller
The display controller executes the commands identified by the command decoder. It
contains the status registers of the PCF8566 and coordinates their effects. The controller
also loads display data into the display RAM as required by the storage order.
9. Internal circuitry
V
LCD
V
SS
BP0 to BP3,
S0 to S23
SDA, SCL, SYNC,
CLK, OSC, A0 to A2,
SA0
V
DD
001aai456
Fig 19. Device protection diagram
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
26 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
10. Limiting values
CAUTION
Static voltages across the liquid crystal display can build up when the LCD supply voltage
(VLCD) is on while the IC supply voltage (VDD) is off, or vice versa. This may cause unwanted
display artifacts. To avoid such artifacts, VLCD and VDD must be applied or removed together.
Table 18. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
VDD
Parameter
Conditions
Min
−0.5
−0.5
−0.5
Max
7.0
7.0
7.0
Unit
V
supply voltage
LCD supply voltage
input voltage
[1]
[1]
VLCD
VI
V
on each of the pins SCL,
SDA, A0 to A2, OSC, CLK,
SYNC and SA0
V
VO
output voltage
on each of the pins S0 to S23
and BP0 to BP3
−0.5
7.0
V
II
input current
output current
supply current
−20
−25
−50
−50
+20
+25
+50
+50
mA
mA
mA
mA
IO
IDD
ISS
ground supply
current
IDD(LCD)
Ptot
LCD supply current
−50
+50
400
mA
total power
dissipation
per package
-
mW
Po
output power
-
100
mW
[2]
Tstg
storage
−65
+150
°C
temperature
[3]
[4]
[5]
Vesd
electrostatic
discharge voltage
HBM
MM
-
-
-
±2000
±200
100
V
V
Ilu
latch-up current
mA
[1] Values with respect to VDD
.
[2] According to the NXP store and transport conditions (document SNW-SQ-623) the devices have to be
stored at a temperature of +5 °C to +45 °C and a humidity of 25 % to 75 %.
[3] Pass level; Human Body Model (HBM) according to JESD22-A114.
[4] Pass level; Machine Model (MM), according to JESD22-A115.
[5] Pass level; latch-up testing, according to JESD78.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
27 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
11. Static characteristics
Table 19. Static characteristics
VSS = 0 V; VDD = 2.5 V to 6.0 V; VLCD = VDD − 2.5 V to VDD − 6.0 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Supplies
VDD
Parameter
Conditions
Min
Typ
Max
Unit
supply voltage
2.5
-
6.0
V
VLCD
LCD supply voltage
supply current:
V
DD − 6.0
-
V
DD − 2.5
V
[1]
[1]
IDD
fclk = 200 kHz
VDD = 3.5 V;
-
30
15
90
40
µA
µA
IDD(lp)
low-power mode supply current
-
V
LCD = 0 V;
f
clk = 35 kHz;
A0 to A2 tied to
VSS
Logic
Vi
input voltage
V
SS − 0.5
-
-
-
-
VDD + 0.5
0.3VDD
VDD
V
VIL
LOW-level input voltage
HIGH-level input voltage
LOW-level output current
VSS
V
VIH
IOL
0.7VDD
−1
V
on pins CLK and
SYNC;
-
mA
V
V
OL = 1.0 V;
DD = 5.0 V
IL
leakage current
on pins SA0, CLK,
OSC, A0 to A2;
VI = VDD or VSS
−1
-
+1
µA
IOH(CLK)
Ipd
HIGH-level output current on pin
CLK
VOH = 4.0 V;
-
-
+1
mA
V
DD = 5.0 V
pull-down current
on pins OSC and
A0 to A2;
15
50
150
µA
VI = 1.0 V;
V
DD = 5.0 V
RPU
VPOR
CI
pull-up resistance
power-on reset voltage
input capacitance
on pin SYNC
15
-
25
1.3
-
60
2
kΩ
V
[2]
[3]
-
7
pF
I2C-bus; pins SDA and SCL
Vi
input voltage
VSS − 0.5
-
6
V
VIL
VIH
IL
LOW-level input voltage
HIGH-level input voltage
leakage current
VSS
0.7VDD
−1
-
0.3VDD
V
-
6
V
VI = VDD or VSS
VOL = 0.4 V;
0
-
+1
-
µA
mA
IOL
LOW-level output current
−3
V
DD = 5.0 V
[3]
CI
input capacitance
spike pulse width
-
-
-
-
7
pF
ns
tw(spike)
on bus
100
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
28 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Table 19. Static characteristics …continued
VSS = 0 V; VDD = 2.5 V to 6.0 V; VLCD = VDD − 2.5 V to VDD − 6.0 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
LCD outputs
VBP
Parameter
Conditions
Min
Typ
Max
Unit
voltage on pin BP
voltage on pin S
output impedance
BP0 to BP3;
-
-
-
-
±20
±20
1
-
mV
mV
kΩ
kΩ
C
bpl = 35 nF
S0 to S23;
sgm = 5 nF
on pin BP0 to BP3;
LCD = VDD − 5 V
on pin S0 to S23;
LCD = VDD − 5 V
VS
Zo
-
C
[4]
[4]
5
7
V
3
V
[1] Outputs open; inputs at VSS or VDD; external clock with 50 % duty factor; I2C-bus inactive.
[2] Resets all logic when VDD < VPOR
.
[3] Periodically sampled, not 100 % tested.
[4] Outputs measured one at a time.
11.1 Typical supply current characteristics
mgg397
mgg398
40
24
I
DD
I
(µA)
DD
(µA)
−40 °C
+85 °C
−40 °C
+85 °C
30
16
20
8
0
10
0
0
2
4
6
8
0
2
4
6
8
V
(V)
V
(V)
DD
DD
VLCD = 0 V; fclk(ext) = 200 kHz.
VLCD = 0 V; fclk(ext) = 35 kHz.
Fig 20. Normal mode
Fig 21. Low power mode
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
29 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
11.2 Typical LCD output characteristics
mgg400
mgg399
6
4
12
R
BP
R
S
(kΩ)
(kΩ)
8
−40 °C
2
0
4
0
+25 °C
+85 °C
0
2
4
6
8
0
2
4
6
8
V
(V)
V
(V)
DD
DD
VDD = 5 V; Tamb = −40 °C to +85 °C.
VDD = 5 V.
Fig 22. Backplane output impedance BP0 to BP3 (RBP
)
Fig 23. Segment output impedance S0 to S23 (RS)
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
30 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
12. Dynamic characteristics
Table 20. Dynamic characteristics
VSS = 0 V; VDD = 2.5 V to 6.0 V; VLCD = VDD − 2.5 V to VDD − 6.0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. [1]
Symbol
Clock
fclk
Parameter
Conditions
Min
Typ
Max
Unit
[2]
clock frequency
normal mode;
125
21
200
31
315
48
kHz
kHz
V
DD = 5 V
power saving mode;
DD = 3.5 V
V
tclk(H)
tclk(L)
HIGH-level clock time
LOW-level clock time
1
1
-
-
-
-
-
-
-
µs
µs
ns
µs
µs
-
tPD(SYNC_N) SYNC propagation delay
400
-
tSYNC_NL
tPD(drv)
SYNC LOW time
1
-
driver propagation delay
with test loads;
LCD = VDD − 5 V
30
V
I2C-bus
tBUF
bus free time between a STOP and
START condition
4.7
-
-
µs
tHD;STA
tLOW
hold time (repeated) START condition
low period of the SCL clock
4.0
4.7
4.0
4.7
-
-
-
-
-
-
-
-
µs
µs
µs
µs
tHIGH
high period of the SCL clock
tSU;STA
set-up time for a repeated START
condition
tHD;DAT
tSU;DAT
tr
data hold time
0
-
-
-
-
-
-
ns
ns
µs
ns
µs
data set-up time
250
-
rise time of both SDA and SCL signals
fall time of both SDA and SCL signals
set-up time for STOP condition
-
1.0
300
-
tf
-
tSU;STO
4.7
[1] All timing values referred to VIH and VIL levels with an input voltage swing of VSS to VDD
[2] At fclk < 125 kHz, I2C-bus maximum transmission speed is derated.
.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
31 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
1
f
clk
t
t
clk(H)
clk(L)
0.7V
DD
CLK
0.3V
DD
0.7V
DD
SYNC
0.3V
DD
t
PD(SYNC_N)
t
SYNC_NL
0.5 V
(V
BP0 to BP3
S0 to S23
= 5 V)
DD
0.5 V
mgg391
t
PD(drv)
Fig 24. Driver timing waveforms
SDA
t
t
t
f
BUF
LOW
SCL
SDA
t
HD;STA
t
t
t
SU;DAT
r
HD;DAT
t
HIGH
t
SU;STA
t
SU;STO
mga728
Fig 25. I2C-bus timing waveforms
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
32 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
13. Application information
13.1 Cascaded operation
Large display configurations of up to sixteen PCF8566s can be recognized on the same
I2C-bus by using the 3-bit hardware subaddress (A0, A1 and A2) and the programmable
I2C-bus slave address (SA0).
Table 21. Addressing cascaded PCF8566
Cluster
Bit SA0
Pin A2
Pin A1
Pin A0
Device
1
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
2
3
4
5
6
7
2
1
8
9
10
11
12
13
14
15
Cascaded PCF8566s are synchronized. They can share the backplane signals from one
of the devices in the cascade. Such an arrangement is cost-effective in large LCD
applications since the backplane outputs of only one device need to be through-plated to
the backplane electrodes of the display. The other PCF8566s of the cascade contribute
additional segment outputs but their backplane outputs are left open-circuit (see
Figure 26).
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
33 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
V
DD
V
LCD
5
12
SDA
SCL
1
2
24 segment drives
17 to 40
LCD PANEL
SYNC
CLK
PCF8566
3
4
6
(up to 1536
elements)
13 to 16
OSC
BP0 to BP3
(open-circuit)
7
8
9
10 11
A0 A1 A2 SA0 V
SS
V
LCD
V
DD
t
rise
R ≤
2 C
V
V
LCD
bus
DD
5
12
SDA
SCL
HOST
MICRO-
1
24 segment drives
17 to 40
2
3
4
6
PROCESSOR/
MICRO-
CONTROLLER
SYNC
CLK
PCF8566
4 backplanes
BP0 to BP3
13 to 16
OSC
7
8
9
10 11
mgg384
A0 A1 A2 SA0
V
SS
V
SS
Fig 26. Cascaded PCF8566 configuration
The SYNC line is provided to maintain the correct synchronization between all cascaded
PCF8566s. This synchronization is guaranteed after the power-on reset. The only time
that SYNC is likely to be needed is if synchronization is accidentally lost (e.g. by noise in
adverse electrical environments or by defining a multiplex mode when PCF8566s with
differing SA0 levels are cascaded).
SYNC is organized as an input/output pin; the output selection being realized as an
open-drain driver with an internal pull-up resistor. A PCF8566 asserts the SYNC line at
the onset of its last active backplane signal and monitors the SYNC line at all other times.
If synchronization in the cascade is lost, it is restored by the first PCF8566 to assert
SYNC. The timing relationship between the backplane waveforms and the SYNC signal
for the various drive modes of the PCF8566 are shown in Figure 27.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
34 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
1
T
=
fr
f
fr
BP0
SYNC
(a) static drive mode.
BP0
(1/2 bias)
BP0
(1/3 bias)
SYNC
(b) 1:2 multiplex drive mode.
BP0
(1/3 bias)
SYNC
(c) 1:3 multiplex drive mode.
BP0
(1/3 bias)
SYNC
(d) 1:4 multiplex drive mode.
mgl755
Fig 27. Synchronization of the cascade for the various PCF8566 drive modes
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
35 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Single plane wiring of packaged PCF8566s is illustrated in Figure 28.
SDA
SCL
SYNC
CLK
V
DD
V
SS
V
LCD
1
2
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
1
2
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
SDA
SCL
S23
S22
S21
S20
S19
S18
S17
S16
S15
S14
S13
S12
S11
S10
S9
S47
S46
S45
S44
S43
S42
S41
S40
S39
S38
S37
S36
S35
S34
S33
S32
S31
S30
S29
S28
3
3
SYNC
CLK
4
4
V
5
5
DD
6
6
OSC
A0
7
7
8
8
A1
9
9
A2
10
11
12
13
14
15
16
17
18
19
20
10
11
12
13
14
15
16
17
18
19
20
SA0
V
SS
V
LCD
BP0
BP2
BP1
BP3
S0
BP0
BP2
BP1
BP3
S24
S25
S26
S27
PCF8566
PCF8566
open-circuit
S8
S7
S1
S6
S2
S5
S3
S4
S0
S23
S24
S47
SEGMENTS
mgg386
BACKPLANES
Fig 28. Single plane wiring of packaged PCF8566s
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
36 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
14. Package outline
DIP40: plastic dual in-line package; 40 leads (600 mil)
SOT129-1
D
M
E
A
2
A
L
A
1
c
e
w M
Z
b
1
(e )
1
b
M
H
40
21
pin 1 index
E
1
20
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
(1)
A
A
A
(1)
(1)
Z
1
2
w
UNIT
mm
b
b
c
D
E
e
e
L
M
M
1
1
E
H
max.
min.
max.
max.
1.70
1.14
0.53
0.38
0.36
0.23
52.5
51.5
14.1
13.7
3.60
3.05
15.80
15.24
17.42
15.90
4.7
0.51
4
2.54
0.1
15.24
0.6
0.254
0.01
2.25
0.067
0.045
0.021
0.015
0.014
0.009
2.067
2.028
0.56
0.54
0.14
0.12
0.62
0.60
0.69
0.63
inches
0.19
0.02
0.16
0.089
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-13
SOT129-1
051G08
MO-015
SC-511-40
Fig 29. Package outline SOT129-1 (DIP40)
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
37 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
VSO40: plastic very small outline package; 40 leads
SOT158-1
D
E
A
X
c
y
H
v
M
A
E
Z
40
21
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
detail X
1
20
w
M
b
p
e
0
5
scale
10 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
max.
(1)
(2)
(1)
UNIT
mm
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
Z
θ
1
2
3
p
E
0.3
0.1
2.45
2.25
0.42
0.30
0.22
0.14
15.6
15.2
7.6
7.5
12.3
11.8
1.7
1.5
1.15
1.05
0.6
0.3
2.7
0.25
0.01
0.762
0.03
2.25
0.089
0.2
0.1
0.1
7o
0o
0.012 0.096
0.004 0.089
0.017 0.0087 0.61
0.012 0.0055 0.60
0.30
0.29
0.48
0.46
0.067 0.045
0.059 0.041
0.024
0.012
inches
0.008 0.004 0.004
0.11
Notes
1. Plastic or metal protrusions of 0.4 mm (0.016 inch) maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
95-01-24
03-02-19
SOT158-1
Fig 30. Package outline SOT158-1 (VSO40)
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
38 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
15. Bare die outline
Wire bond die; 40 bonding pads; 2.5 x 2.91 x 0.381 mm
PCF8566U
D
e
A
P C 8 5 6 6 - 1
25
24
23
22
21
20
19
18
17
16
C1
15
e
26
14
13
12
F
27
28
29
30
31
32
33
34
11
10
9
x
E
0
0
y
8
C2
P
P
3
4
7
35
6
P
P
2
36
37
38
39
40
1
2
3
4
5
1
X
detail X
0
0.5
scale
1 mm
DIMENSIONS (mm are the original dimensions)
(1)
(2)
(1)
(2)
UNIT
A
D
E
e
P
P
P
P
4
1
2
3
max 0.406
0.548
mm
nom 0.381 2.5
min 0.356
2.91 0.200 0.12 0.106 0.12 0.106
0.018
Notes
1. Pad size
2. Passivation opening
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
JEITA
08-06-19
08-09-03
PCF8566U
Fig 31. Bare die outline PCF8566U
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
39 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Table 22. Bonding pad description
All x/y coordinates represent the position of the center of each pad with respect to the center
(x/y = 0) of the chip (see Figure 31).
Symbol
SDA
SCL
SYNC
CLK
VDD
OSC
A0
Pad
1
X (µm)
200
Y (µm)
−1235
−1235
−1235
−1235
−1235
−1235
−825
−625
−425
−225
−25
Description
I2C-bus data input / output
I2C-bus clock input / output
cascade synchronization input / output
external clock input / output
supply voltage
2
400
3
604
4
856
5
1062
1080
1080
1080
1080
1080
1080
1080
1080
1080
1080
1074
874
6
oscillator select
I2C-bus subaddress input
7
A1
8
A2
9
SA0
VSS
VLCD
BP0
BP2
BP1
BP3
S0
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
I2C-bus slave address bit 0 input
logic ground
347
LCD supply voltage
547
LCD backplane output
747
947
1235
1235
1235
1235
1235
1235
1235
1235
1235
1235
765
LCD segment output
S1
674
S2
474
S3
274
S4
−274
−474
−674
−874
−1074
−1080
−1080
−1080
−1080
−1080
−1080
−1080
−1080
−1080
−1080
−1056
−830
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
565
365
165
−35
−235
−435
−635
−835
−1035
−1235
−1235
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
40 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Table 22. Bonding pad description …continued
All x/y coordinates represent the position of the center of each pad with respect to the center
(x/y = 0) of the chip (see Figure 31).
Symbol
S21
Pad
38
X (µm)
−630
−430
−230
Y (µm)
−1235
−1235
−1235
Description
S22
39
S23
40
REF
C1
REF
F
REF
001aai300
C2
Fig 32. Alignment marks
Table 23. Alignment marks
Symbol
X (µm)
1100
325
Y (µm)
C1
C2
F
1090
−625
700
−790
16. Handling information
All input and output pins are protected against ElectroStatic Discharge (ESD) under
normal handling. When handling Metal-Oxide Semiconductor (MOS) devices ensure that
all normal precautions are taken as described in JESD625-A, IEC 61340-5 or equivalent
standards.
17. Packing information
Tray information for the PCF8566U is shown in Figure 33, Figure 35 and Table 24.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
41 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
G
A
C
H
D
B
F
E
001aai237
Fig 33. Tray details
001aaj619
Fig 34. Tray alignment
Table 24. Tray dimensions
Symbol
Description
Value
A
B
C
D
pocket pitch; x direction
pocket pitch; y direction
pocket width; x direction
pocket width; y direction
4.43 mm
4.43 mm
3.04 mm
3.04 mm
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
42 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
Table 24. Tray dimensions …continued
Symbol
Description
Value
E
F
G
H
x
tray width; x direction
tray width; y direction
50.8 mm
50.8 mm
cut corner to pocket 1,1 center
cut corner to pocket 1,1 center
number of pockets; x direction
number of pockets; y direction
5.47 mm
5.47 mm
10
y
10
18. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
18.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
18.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
• Board specifications, including the board finish, solder masks and vias
• Package footprints, including solder thieves and orientation
• The moisture sensitivity level of the packages
• Package placement
• Inspection and repair
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
43 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
• Lead-free soldering versus SnPb soldering
18.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
18.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 35) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 25 and 26
Table 25. SnPb eutectic process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
235
≥ 350
220
< 2.5
≥ 2.5
220
220
Table 26. Lead-free process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
260
350 to 2000
> 2000
260
< 1.6
260
250
245
1.6 to 2.5
> 2.5
260
245
250
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 35.
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
44 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 35. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
19. Abbreviations
Table 27. Abbreviations
Acronym
CMOS
DC
Description
Complementary Metal Oxide Semiconductor
Direct Current
HBM
I2C
Human Body Model
Inter-Integrated Circuit
Integrated Circuit
IC
LCD
MM
Liquid Crystal Display
Machine Model
MSL
POR
RC
Moisture Sensitivity Level
Power-On Reset
Resistance and Capacitance
Random Access Memory
Root Mean Square
RAM
RMS
SMD
TTL
Surface Mount Device
Transistor-Transistor Logic
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
45 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
20. Revision history
Table 28. Revision history
Document ID
PCF8566_7
Release date
20090225
Data sheet status
Change notice
Supersedes
Product data sheet
-
PCF8566_6
Modifications:
• The format of this data sheet has been redesigned to comply with the new identity
guidelines of NXP Semiconductors.
• Legal texts have been adapted to the new company name where appropriate.
• Added U and TS type
• Added tray information
• Changed values in limiting values table from relative to absolute values
• Changed letter symbols to NXP approved symbols
• Rewritten chapter 7.3
PCF8566_6
PCF8566_5
PCF8566_4
PCF8566_3
19980504
19970402
19961203
19961029
Product specification
Product specification
Product specification
Product specification
-
-
-
-
PCF8566_5
PCF8566_4
PCF8566_3
PCF8566_2
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
46 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
21. Legal information
21.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
transportation conditions. If there are data sheet limits not guaranteed, these
will be separately indicated in the data sheet. There are no post-packing tests
performed on individual die or wafers.
21.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
NXP Semiconductors has no control of third party procedures in the sawing,
handling, packing or assembly of the die. Accordingly, NXP Semiconductors
assumes no liability for device functionality or performance of the die or
systems after third party sawing, handling, packing or assembly of the die. It
is the responsibility of the customer to test and qualify their application in
which the die is used.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
All die sales are conditioned upon and subject to the customer entering into a
written die sale agreement with NXP Semiconductors through its legal
department.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
21.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
21.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
Bare die — All die are tested on compliance with their related technical
specifications as stated in this data sheet up to the point of wafer sawing and
are handled in accordance with the NXP Semiconductors storage and
I2C-bus — logo is a trademark of NXP B.V.
22. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
PCF8566_7
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 — 25 February 2009
47 of 48
PCF8566
NXP Semiconductors
Universal LCD driver for low multiplex rates
23. Contents
1
2
3
4
5
General description . . . . . . . . . . . . . . . . . . . . . . 1
8.4
9
Display controller . . . . . . . . . . . . . . . . . . . . . . 26
Internal circuitry . . . . . . . . . . . . . . . . . . . . . . . 26
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 27
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
10
11
11.1
11.2
Static characteristics . . . . . . . . . . . . . . . . . . . 28
Typical supply current characteristics. . . . . . . 29
Typical LCD output characteristics. . . . . . . . . 30
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
12
Dynamic characteristics. . . . . . . . . . . . . . . . . 31
Application information . . . . . . . . . . . . . . . . . 33
Cascaded operation. . . . . . . . . . . . . . . . . . . . 33
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 37
Bare die outline . . . . . . . . . . . . . . . . . . . . . . . . 39
Handling information . . . . . . . . . . . . . . . . . . . 41
Packing information . . . . . . . . . . . . . . . . . . . . 41
13
13.1
14
7
7.1
7.2
7.3
Functional description . . . . . . . . . . . . . . . . . . . 6
Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 7
LCD bias generator. . . . . . . . . . . . . . . . . . . . . . 7
LCD voltage selector . . . . . . . . . . . . . . . . . . . . 7
LCD drive mode waveforms . . . . . . . . . . . . . . 10
Static drive mode . . . . . . . . . . . . . . . . . . . . . . 10
1:2 Multiplex drive mode. . . . . . . . . . . . . . . . . 11
1:3 Multiplex drive mode. . . . . . . . . . . . . . . . . 13
1:4 multiplex drive mode. . . . . . . . . . . . . . . . . 14
Oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Internal clock. . . . . . . . . . . . . . . . . . . . . . . . . . 15
External clock . . . . . . . . . . . . . . . . . . . . . . . . . 15
Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Display register. . . . . . . . . . . . . . . . . . . . . . . . 16
Shift register . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Segment outputs. . . . . . . . . . . . . . . . . . . . . . . 16
Backplane outputs . . . . . . . . . . . . . . . . . . . . . 16
Display RAM. . . . . . . . . . . . . . . . . . . . . . . . . . 16
Data pointer . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Sub-address counter . . . . . . . . . . . . . . . . . . . 19
Output bank selector. . . . . . . . . . . . . . . . . . . . 19
Input bank selector . . . . . . . . . . . . . . . . . . . . . 19
Blinker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
15
16
7.4
17
7.4.1
7.4.2
7.4.3
7.4.4
7.5
7.5.1
7.5.2
7.6
7.7
7.8
7.9
7.10
7.11
7.12
7.13
7.14
7.15
7.16
18
Soldering of SMD packages . . . . . . . . . . . . . . 43
Introduction to soldering. . . . . . . . . . . . . . . . . 43
Wave and reflow soldering . . . . . . . . . . . . . . . 43
Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 44
Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . 44
18.1
18.2
18.3
18.4
19
20
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 45
Revision history . . . . . . . . . . . . . . . . . . . . . . . 46
21
Legal information . . . . . . . . . . . . . . . . . . . . . . 47
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 47
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 47
21.1
21.2
21.3
21.4
22
23
Contact information . . . . . . . . . . . . . . . . . . . . 47
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
8
8.1
Basic architecture . . . . . . . . . . . . . . . . . . . . . . 20
Characteristics of the I2C-bus. . . . . . . . . . . . . 20
Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
START and STOP conditions . . . . . . . . . . . . . 21
System configuration . . . . . . . . . . . . . . . . . . . 21
Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . 21
PCF8566 I2C-bus controller . . . . . . . . . . . . . . 22
Input filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
I2C-bus protocol . . . . . . . . . . . . . . . . . . . . . . . 22
Command decoder . . . . . . . . . . . . . . . . . . . . . 24
Mode set command . . . . . . . . . . . . . . . . . . . . 24
Load data pointer command. . . . . . . . . . . . . . 25
Device select command . . . . . . . . . . . . . . . . . 25
Bank select command . . . . . . . . . . . . . . . . . . 25
Blink command . . . . . . . . . . . . . . . . . . . . . . . . 26
8.1.1
8.1.1.1
8.1.2
8.1.3
8.1.4
8.1.5
8.2
8.3
8.3.1
8.3.2
8.3.3
8.3.4
8.3.5
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2009.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 25 February 2009
Document identifier: PCF8566_7
相关型号:
©2020 ICPDF网 联系我们和版权申明