PN5120A0HN/C1 [NXP]
SPECIALTY TELECOM CIRCUIT, PQCC40, 6 X 6 MM X 0.85 MM HEIGHT, PLASTIC, SOT-618, HVQFN-40;型号: | PN5120A0HN/C1 |
厂家: | NXP |
描述: | SPECIALTY TELECOM CIRCUIT, PQCC40, 6 X 6 MM X 0.85 MM HEIGHT, PLASTIC, SOT-618, HVQFN-40 电信 电信集成电路 |
文件: | 总136页 (文件大小:1108K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PN512
Full NFC Forum compliant solution
Rev. 4.5 — 17 December 2013
111345
Product data sheet
COMPANY PUBLIC
1. Introduction
This document describes the functionality and electrical specifications of the
transceiver IC PN512.
The PN512 is a highly integrated transceiver IC for contactless communication at
13.56 MHz. This transceiver IC utilizes an outstanding modulation and demodulation
concept completely integrated for different kinds of contactless communication methods
and protocols at 13.56 MHz.
1.1 Different available versions
The PN512 is available in three versions:
• PN5120A0HN1/C2 (HVQFN32), PN5120A0HN/C2 (HVQFN40) and PN5120A0ET/C2
(TFBGA64), hereafter named as version 2.0
• PN512AA0HN1/C2 (HVQFN32) and PN512AA0HN1/C2BI (HVQFN32 with Burn In),
hereafter named as industrial version, fulfilling the automotive qualification stated in
AEC-Q100 grade 3 from the Automotive Electronics Council, defining the critical
stress test qualification for automotive integrated circuits (ICs).
• PN5120A0HN1/C1(HVQFN32) and PN5120A0HN/C1 (HVQFN40), hereafter named
as version 1.0
The data sheet describes the functionality for the industrial version and version 2.0. The
differences of the version 1.0 to the version 2.0 are summarized in Section 21. The
industrial version has only differences within the outlined characteristics and limitations.
2. General description
The PN512 transceiver ICs support 4 different operating modes
• Reader/Writer mode supporting ISO/IEC 14443A/MIFARE and FeliCa scheme
• Reader/Writer mode supporting ISO/IEC 14443B
• Card Operation mode supporting ISO/IEC 14443A/MIFARE and FeliCa scheme
• NFCIP-1 mode
Enabled in Reader/Writer mode for ISO/IEC 14443A/MIFARE, the PN512’s internal
transmitter part is able to drive a reader/writer antenna designed to communicate with
ISO/IEC 14443A/ MIFARE cards and transponders without additional active circuitry. The
receiver part provides a robust and efficient implementation of a demodulation and
PN512
NXP Semiconductors
Full NFC Forum compliant solution
decoding circuitry for signals from ISO/IEC 14443A/MIFARE compatible cards and
transponders. The digital part handles the complete ISO/IEC 14443A framing and error
detection (Parity & CRC).
The PN512 supports MIFARE 1K or MIFARE 4K emulation products. The PN512 supports
contactless communication using MIFARE higher transfer speeds up to 424 kbit/s in both
directions.
Enabled in Reader/Writer mode for FeliCa, the PN512 transceiver IC supports the FeliCa
communication scheme. The receiver part provides a robust and efficient implementation
of the demodulation and decoding circuitry for FeliCa coded signals. The digital part
handles the FeliCa framing and error detection like CRC. The PN512 supports contactless
communication using FeliCa Higher transfer speeds up to 424 kbit/s in both directions.
The PN512 supports all layers of the ISO/IEC 14443B reader/writer communication
scheme, given correct implementation of additional components, like oscillator, power
supply, coil etc. and provided that standardized protocols, e.g. like ISO/IEC 14443-4
and/or ISO/IEC 14443B anticollision are correctly implemented.
In Card Operation mode, the PN512 transceiver IC is able to answer to a reader/writer
command either according to the FeliCa or ISO/IEC 14443A/MIFARE card interface
scheme. The PN512 generates the digital load modulated signals and in addition with an
external circuit the answer can be sent back to the reader/writer. A complete card
functionality is only possible in combination with a secure IC using the S2C interface.
Additionally, the PN512 transceiver IC offers the possibility to communicate directly to an
NFCIP-1 device in the NFCIP-1 mode. The NFCIP-1 mode offers different communication
mode and transfer speeds up to 424 kbit/s according to the Ecma 340 and ISO/IEC 18092
NFCIP-1 Standard. The digital part handles the complete NFCIP-1 framing and error
detection.
Various host controller interfaces are implemented:
• 8-bit parallel interface1
• SPI interface
• serial UART (similar to RS232 with voltage levels according pad voltage supply)
• I2C interface.
A purchaser of this NXP IC has to take care for appropriate third party patent licenses.
1. 8-bit parallel Interface only available in HVQFN40 package.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
2 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
3. Features and benefits
Highly integrated analog circuitry to demodulate and decode responses
Buffered output drivers for connecting an antenna with the minimum number of
external components
Integrated RF Level detector
Integrated data mode detector
Supports ISO/IEC 14443 A/MIFARE
Supports ISO/IEC 14443 B Read/Write modes
Typical operating distance in Read/Write mode up to 50 mm depending on the
antenna size and tuning
Typical operating distance in NFCIP-1 mode up to 50 mm depending on the antenna
size and tuning and power supply
Typical operating distance in ISO/IEC 14443A/MIFARE card or FeliCa Card Operation
mode of about 100 mm depending on the antenna size and tuning and the external
field strength
Supports MIFARE 1K or MIFARE 4K emulation encryption in Reader/Writer mode
ISO/IEC 14443A higher transfer speed communication at 212 kbit/s and 424 kbit/s
Contactless communication according to the FeliCa scheme at 212 kbit/s and
424 kbit/s
Integrated RF interface for NFCIP-1 up to 424 kbit/s
S2C interface
Additional power supply to directly supply the smart card IC connected via S2C
Supported host interfaces
SPI up to 10 Mbit/s
I2C-bus interface up to 400 kBd in Fast mode, up to 3400 kBd in High-speed mode
RS232 Serial UART up to 1228.8 kBd, with voltage levels dependant on pin
voltage supply
8-bit parallel interface with and without Address Latch Enable
FIFO buffer handles 64 byte send and receive
Flexible interrupt modes
Hard reset with low power function
Power-down mode per software
Programmable timer
Internal oscillator for connection to 27.12 MHz quartz crystal
2.5 V to 3.6 V power supply
CRC coprocessor
Programmable I/O pins
Internal self-test
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
3 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
4. Quick reference data
Table 1.
Quick reference data
Symbol Parameter
Conditions
Min
Typ
Max Unit
[1][2]
[3]
VDDA
VDDD
analog supply voltage
digital supply voltage
VDD(PVDD) VDDA = VDDD = VDD(TVDD)
;
2.5
-
3.6
V
VSSA = VSSD = VSS(PVSS) = VSS(TVSS) = 0 V
VDD(TVDD) TVDD supply voltage
VDD(PVDD) PVDD supply voltage
VDD(SVDD) SVDD supply voltage
1.6
1.6
-
-
3.6
3.6
V
V
VSSA = VSSD = VSS(PVSS) = VSS(TVSS) = 0 V
VDDA = VDDD = VDD(TVDD) = VDD(PVDD) = 3 V
hard power-down; pin NRSTPD set LOW
soft power-down; RF level detector on
pin DVDD; VDDD = 3 V
Ipd
power-down current
[4]
[4]
-
-
-
-
-
5
A
A
-
10
9
IDDD
IDDA
digital supply current
analog supply current
6.5
7
mA
mA
pin AVDD; VDDA = 3 V, CommandReg register’s
RcvOff bit = 0
10
pin AVDD; receiver switched off; VDDA = 3 V,
CommandReg register’s RcvOff bit = 1
-
3
5
mA
[5]
IDD(PVDD) PVDD supply current
IDD(TVDD) TVDD supply current
pin PVDD
-
-
40
mA
mA
C
[6][7][8]
pin TVDD; continuous wave
HVQFN32, HVQFN40, TFBGA64
-
60
100
+85
Tamb
ambient temperature
30
lndustrial version:
Ipd
power-down current
VDDA = VDDD = VDD(TVDD) = VDD(PVDD) = 3 V
hard power-down; pin NRSTPD set LOW
soft power-down; RF level detector on
HVQFN32
[4]
[4]
-
-
-
-
15
A
A
C
-
30
Tamb
ambient temperature
40
+90
[1] Supply voltages below 3 V reduce the performance in, for example, the achievable operating distance.
[2] DDA, VDDD and VDD(TVDD) must always be the same voltage.
V
[3] VDD(PVDD) must always be the same or lower voltage than VDDD
.
[4] Ipd is the total current for all supplies.
[5]
IDD(PVDD) depends on the overall load at the digital pins.
[6] IDD(TVDD) depends on VDD(TVDD) and the external circuit connected to pins TX1 and TX2.
[7] During typical circuit operation, the overall current is below 100 mA.
[8] Typical value using a complementary driver configuration and an antenna matched to 40 between pins TX1 and TX2 at 13.56 MHz.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
4 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
5. Ordering information
Table 2.
Ordering information
Type number
Package
Name
Description
Version
PN5120A0HN1/C2
PN5120A0HN/C2
PN512AA0HN1/C2
HVQFN32 plastic thermal enhanced very thin quad flat package; no leads;
SOT617-1
SOT618-1
SOT617-1
SOT617-1
SOT617-1
SOT618-1
SOT1336-1
32 terminal; body 5 5 0.85 mm
HVQFN40 plastic thermal enhanced very thin quad flat package; no leads;
40 terminals; body 6 6 0.85 mm
HVQFN32 plastic thermal enhanced very thin quad flat package; no leads;
32 terminal; body 5 5 0.85 mm
PN512AA0HN1/C2BI HVQFN32 plastic thermal enhanced very thin quad flat package; no leads;
32 terminal; body 5 5 0.85 mm
PN5120A0HN1/C1
PN5120A0HN/C1
PN5120A0ET/C2
HVQFN32 plastic thermal enhanced very thin quad flat package; no leads;
32 terminal; body 5 5 0.85 mm
HVQFN40 plastic thermal enhanced very thin quad flat package; no leads;
40 terminals; body 6 6 0.85 mm
TFBGA64 plastic thin fine-pitch ball grid array package; 64 balls
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
5 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
6. Block diagram
The analog interface handles the modulation and demodulation of the analog signals
according to the Card Receiving mode, Reader/Writer mode and NFCIP-1 mode
communication scheme.
The RF level detector detects the presence of an external RF-field delivered by the
antenna to the RX pin.
The Data mode detector detects a MIFARE, FeliCa or NFCIP-1 mode in order to prepare
the internal receiver to demodulate signals, which are sent to the PN512.
The communication (S2C) interface provides digital signals to support communication for
transfer speeds above 424 kbit/s and digital signals to communicate to a secure IC.
The contactless UART manages the protocol requirements for the communication
protocols in cooperation with the host. The FIFO buffer ensures fast and convenient data
transfer to and from the host and the contactless UART and vice versa.
Various host interfaces are implemented to meet different customer requirements.
REGISTER BANK
ANALOG
INTERFACE
CONTACTLESS
UART
ANTENNA
FIFO
BUFFER
SERIAL UART
SPI
I C-BUS
HOST
2
001aaj627
Fig 1. Simplified block diagram of the PN512
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
6 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
D6/ADR_0/
MOSI/MX
D2/ADR_4
D1/ADR_5 D3/ADR_3
25 26 27
D4/ADR_2
D5/ADR_1/
D7/SCL/
SDA/NSS/RX EA I2C
24 32
PVDD PVSS
SCK/DTRQ
MISO/TX
1
28
29
30
31
2
5
3
4
DVDD
DVSS
VOLTAGE
MONITOR
AND
POWER ON
DETECT
2
SPI, UART, I C-BUS INTERFACE CONTROL
15
18
AVDD
AVSS
FIFO CONTROL
STATE MACHINE
64-BYTE FIFO
BUFFER
RESET
CONTROL
COMMAND REGISTER
PROGRAMABLE TIMER
INTERRUPT CONTROL
CRC16
6
POWER-DOWN
CONTROL
NRSTPD
IRQ
CONTROL REGISTER
BANK
23
MIFARE CLASSIC UNIT
GENERATION AND CHECK
RANDOM NUMBER
GENERATOR
PARALLEL/SERIAL
CONVERTER
BIT COUNTER
PARITY GENERATION AND CHECK
FRAME GENERATION AND CHECK
BIT DECODING
BIT ENCODING
7
8
9
MFIN
SERIAL DATA SWITCH
MFOUT
SVDD
21
22
CLOCK
OSCIN
GENERATION,
FILTERING AND
DISTRIBUTION
AMPLITUDE
RATING
OSCILLATOR
ANALOG TO DIGITAL
CONVERTER
OSCOUT
REFERENCE
VOLTAGE
Q-CLOCK
GENERATION
TEMPERATURE
SENSOR
ANALOG TEST
MULTIPLEXOR
AND
DIGITAL TO
ANALOG
I-CHANNEL
AMPLIFIER
Q-CHANNEL
AMPLIFIER
TRANSMITTER CONTROL
I-CHANNEL
DEMODULATOR
Q-CHANNEL
DEMODULATOR
CONVERTER
16
19
20
17
RX
10, 14
TVSS
11
TX1
13
TX2
12
VMID AUX1 AUX2
TVDD
001aak602
Fig 2. Detailed block diagram of the PN512
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
7 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
7. Pinning information
7.1 Pinning
terminal 1
index area
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
A1
ALE
PVDD
DVDD
IRQ
OSCOUT
OSCIN
AUX2
AUX1
AVSS
RX
DVSS
PN512
PVSS
NRSTPD
SIGIN
SIGOUT
001aan212
Transparent top view
Fig 3. Pinning configuration HVQFN32 (SOT617-1)
terminal 1
index area
1
2
30
29
28
27
26
25
24
23
22
21
A2
A3
NCS
ALE
3
A4
NRD
4
A5
NWR
IRQ
5
PVDD
DVDD
DVSS
PVSS
NRSTPD
SIGIN
PN512
6
OSCOUT
OSCIN
AUX2
AUX1
AVSS
7
8
9
10
001aan213
Transparent top view
Fig 4. Pinning configuration HVQFN40 (SOT618-1)
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
8 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
ball A1
index area
TFBGA64
1
2
3
4
5
6
7
8
A
B
C
D
E
F
G
H
aaa-005873
Transparent top view
Fig 5. Pin configuration TFBGA64 (SOT1336-1)
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
9 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
7.2 Pin description
Table 3.
Pin description HVQFN32
Pin
1
Symbol
A1
Type
I
Description
Address Line
2
PVDD
DVDD
DVSS
PVSS
NRSTPD
PWR
PWR
PWR
PWR
I
Pad power supply
Digital Power Supply
Digital Ground
3
4
5
Pad power supply ground
6
Not Reset and Power Down: When LOW, internal current sinks are switched off, the
oscillator is inhibited, and the input pads are disconnected from the outside world. With
a positive edge on this pin the internal reset phase starts.
7
SIGIN
SIGOUT
SVDD
TVSS
TX1
I
Communication Interface Input: accepts a digital, serial data stream
Communication Interface Output: delivers a serial data stream
S2C Pad Power Supply: provides power to the S2C pads
Transmitter Ground: supplies the output stage of TX1 and TX2
Transmitter 1: delivers the modulated 13.56 MHz energy carrier
Transmitter Power Supply: supplies the output stage of TX1 and TX2
Transmitter 2: delivers the modulated 13.56 MHz energy carrier
Transmitter Ground: supplies the output stage of TX1 and TX2
Analog Power Supply
8
O
9
PWR
PWR
O
10
11
12
13
14
15
16
17
18
19
20
21
TVDD
TX2
PWR
O
TVSS
AVDD
VMID
RX
PWR
PWR
PWR
I
Internal Reference Voltage: This pin delivers the internal reference voltage.
Receiver Input
AVSS
AUX1
AUX2
OSCIN
PWR
O
Analog Ground
Auxiliary Outputs: These pins are used for testing.
O
I
Crystal Oscillator Input: input to the inverting amplifier of the oscillator. This pin is
also the input for an externally generated clock (fosc = 27.12 MHz).
22
23
24
OSCOUT
IRQ
O
O
I
Crystal Oscillator Output: Output of the inverting amplifier of the oscillator.
Interrupt Request: output to signal an interrupt event
ALE
Address Latch Enable: signal to latch AD0 to AD5 into the internal address latch
when HIGH.
25 to 31
D1 to D7
I/O
8-bit Bi-directional Data Bus.
Remark: An 8-bit parallel interface is not available.
Remark: If the host controller selects I2C as digital host controller interface, these pins
can be used to define the I2C address.
Remark: For serial interfaces this pins can be used for test signals or I/Os.
32
A0
I
Address Line
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
10 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 4.
Pin description HVQFN40
Pin
Symbol
A2 to A5
PVDD
Type
I
Description
1 to 4
Address Line
5
6
7
8
9
PWR
PWR
PWR
PWR
I
Pad power supply
Digital Power Supply
Digital Ground
DVDD
DVSS
PVSS
Pad power supply ground
NRSTPD
Not Reset and Power Down: When LOW, internal current sinks are switched off, the
oscillator is inhibited, and the input pads are disconnected from the outside world. With
a positive edge on this pin the internal reset phase starts.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
SIGIN
SIGOUT
SVDD
TVSS
TX1
I
Communication Interface Input: accepts a digital, serial data stream
Communication Interface Output: delivers a serial data stream
S2C Pad Power Supply: provides power to the S2C pads
Transmitter Ground: supplies the output stage of TX1 and TX2
Transmitter 1: delivers the modulated 13.56 MHz energy carrier
Transmitter Power Supply: supplies the output stage of TX1 and TX2
Transmitter 2: delivers the modulated 13.56 MHz energy carrier
Transmitter Ground: supplies the output stage of TX1 and TX2
Analog Power Supply
O
PWR
PWR
O
TVDD
TX2
PWR
O
TVSS
AVDD
VMID
RX
PWR
PWR
PWR
I
Internal Reference Voltage: This pin delivers the internal reference voltage.
Receiver Input
AVSS
AUX1
AUX2
OSCIN
PWR
O
Analog Ground
Auxiliary Outputs: These pins are used for testing.
O
I
Crystal Oscillator Input: input to the inverting amplifier of the oscillator. This pin is
also the input for an externally generated clock (fosc = 27.12 MHz).
25
26
27
28
29
OSCOUT
IRQ
O
O
I
Crystal Oscillator Output: Output of the inverting amplifier of the oscillator.
Interrupt Request: output to signal an interrupt event
NWR
NRD
Not Write: strobe to write data (applied on D0 to D7) into the PN512 register
Not Read: strobe to read data from the PN512 register (applied on D0 to D7)
I
ALE
I
Address Latch Enable: signal to latch AD0 to AD5 into the internal address latch
when HIGH.
30
NCS
I
Not Chip Select: selects and activates the host controller interface of the PN512
8-bit Bi-directional Data Bus.
31 to 38
D0 to D7
I/O
Remark: For serial interfaces this pins can be used for test signals or I/Os.
Remark: If the host controller selects I2C as digital host controller interface, these pins
can be used to define the I2C address.
39 to 40
A0 to A1
I
Address Line
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
11 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 5.
Pin
Pin description TFBGA64
Symbol
Type
Description
A1 to A5, A8,
PVSS
PWR
Pad power supply ground
B3, B4, B8, E1
A6
A7
D4
D2
I/O
I/O
8-bit Bi-directional Data Bus.
Remark: For serial interfaces this pins can be used for test signals or I/Os.
Remark: If the host controller selects I2C as digital host controller interface, these
pins can be used to define the I2C address.
B1
B2
B5
B6
B7
PVDD
A0
PWR
I
Pad power supply
Address Line
D5
I/O
I/O
I/O
8-bit Bi-directional Data Bus.
Remark: For serial interfaces this pins can be used for test signals or I/Os.
Remark: If the host controller selects I2C as digital host controller interface, these
pins can be used to define the I2C address.
D3
D1
C1
C2
C3
C4
DVDD
A1
PWR
I
Digital Power Supply
Address Line
D7
I/O
I/O
8-bit Bi-directional Data Bus.
Remark: For serial interfaces this pins can be used for test signals or I/Os.
D6
Remark: If the host controller selects I2C as digital host controller interface, these
pins can be used to define the I2C address.
C5
C6
IRQ
ALE
O
I
Interrupt Request: output to signal an interrupt event
Address Latch Enable: signal to latch AD0 to AD5 into the internal address latch
when HIGH.
C7, C8, D6, D8, AVSS
E6, E8, F7, G8,
H8
PWR
Analog Ground
D1
D2
DVSS
PWR
I
Digital Ground
NRSTPD
Not Reset and Power Down: When LOW, internal current sinks are switched off,
the oscillator is inhibited, and the input pads are disconnected from the outside
world. With a positive edge on this pin the internal reset phase starts.
D3 to D5, E3 to TVSS
E5, F3, F4,
PWR
Transmitter Ground: supplies the output stage of TX1 and TX2
G1 to G6,
H1, H2, H6
D7
E2
E7
OSCOUT
O
I
Crystal Oscillator Output: Output of the inverting amplifier of the oscillator.
Communication Interface Input: accepts a digital, serial data stream
SIGIN
OSCIN
I
Crystal Oscillator Input: input to the inverting amplifier of the oscillator. This pin
is also the input for an externally generated clock (fosc = 27.12 MHz).
F1
F2
F5
F6
F8
G7
H3
SVDD
SIGOUT
AUX1
AUX2
RX
PWR
S2C Pad Power Supply: provides power to the S2C pads
Communication Interface Output: delivers a serial data stream
Auxiliary Outputs: These pins are used for testing.
O
O
O
I
Receiver Input
VMID
TX1
PWR
O
Internal Reference Voltage: This pin delivers the internal reference voltage.
Transmitter 1: delivers the modulated 13.56 MHz energy carrier
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
12 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 5.
Pin
Pin description TFBGA64
Symbol
TVDD
TX2
Type
PWR
O
Description
H4
Transmitter Power Supply: supplies the output stage of TX1 and TX2
Transmitter 2: delivers the modulated 13.56 MHz energy carrier
Analog Power Supply
H5
H7
AVDD
PWR
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
13 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
8. Functional description
The PN512 transmission module supports the Read/Write mode for
ISO/IEC 14443 A/MIFARE and ISO/IEC 14443 B using various transfer speeds and
modulation protocols.
PN512 transceiver IC supports the following operating modes:
• Reader/Writer mode supporting ISO/IEC 14443A/MIFARE and FeliCa scheme
• Card Operation mode supporting ISO/IEC 14443A/MIFARE and FeliCa scheme
• NFCIP-1 mode
The modes support different transfer speeds and modulation schemes. The following
chapters will explain the different modes in detail.
Note: All indicated modulation indices and modes in this chapter are system parameters.
This means that beside the IC settings a suitable antenna tuning is required to achieve the
optimum performance.
BATTERY
PN512
ISO/IEC 14443 A CARD
MICROCONTROLLER
contactless card
reader/writer
001aan218
Fig 6. PN512 Read/Write mode
8.1 ISO/IEC 14443 A/MIFARE functionality
The physical level communication is shown in Figure 7.
(1)
ISO/IEC 14443 A
READER
ISO/IEC 14443 A CARD
(2)
PN512
001aan219
Fig 7. ISO/IEC 14443 A/MIFARE Read/Write mode communication diagram
The physical parameters are described in Table 4.
Table 6.
Communication overview for ISO/IEC 14443 A/MIFARE reader/writer
Communication
direction
Signal type
Transfer speed
106 kBd
212 kBd
424 kBd
Reader to card (send reader side
data from the PN512 modulation
100 % ASK
100 % ASK
100 % ASK
to a card)
bit encoding
modified Miller
encoding
modified Miller
encoding
modified Miller
encoding
bit length
128 (13.56 s)
64 (13.56 s)
32 (13.56 s)
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
14 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 6.
Communication overview for ISO/IEC 14443 A/MIFARE reader/writer …continued
Communication
direction
Signal type
Transfer speed
106 kBd
212 kBd
424 kBd
Card to reader
(PN512 receives data modulation
card side
subcarrier load
modulation
subcarrier load
modulation
subcarrier load
modulation
from a card)
subcarrier
13.56 MHz/16
13.56 MHz/16
13.56 MHz/16
frequency
bit encoding
Manchester
encoding
BPSK
BPSK
The PN512’s contactless UART and dedicated external host must manage the complete
ISO/IEC 14443 A/MIFARE protocol. Figure 8 shows the data coding and framing
according to ISO/IEC 14443 A/MIFARE.
ISO/IEC 14443 A framing at 106 kBd
start
8-bit data
8-bit data
8-bit data
odd
odd
odd
parity
parity
parity
start bit is 1
ISO/IEC 14443 A framing at 212 kBd, 424 kBd and 848 kBd
start
even
parity
8-bit data
8-bit data
8-bit data
odd
parity
odd
parity
start bit is 0
burst of 32
subcarrier clocks
even parity at the
end of the frame
001aak585
Fig 8. Data coding and framing according to ISO/IEC 14443 A
The internal CRC coprocessor calculates the CRC value based on ISO/IEC 14443 A
part 3 and handles parity generation internally according to the transfer speed. Automatic
parity generation can be switched off using the ManualRCVReg register’s ParityDisable
bit.
8.2 ISO/IEC 14443 B functionality
The PN512 reader IC fully supports international standard ISO 14443 which includes
communication schemes ISO 14443 A and ISO 14443 B.
Refer to the ISO 14443 reference documents Identification cards - Contactless integrated
circuit cards - Proximity cards (parts 1 to 4).
Remark: NXP Semiconductors does not offer a software library to enable design-in of the
ISO 14443 B protocol.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
15 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
8.3 FeliCa reader/writer functionality
The FeliCa mode is the general reader/writer to card communication scheme according to
the FeliCa specification. The following diagram describes the communication on a
physical level, the communication overview describes the physical parameters.
1. PCD to PICC, 8-30 % ASK
Felica READER
Manchester coded, baudrate 212 to 424 kbaud
FeliCa CARD
(PICC)
(PCD)
PN512
2. PICC to PCD, > 12 % ASK loadmodulation
Manchester coded, baudrate 212 to 424 kbaud
001aan214
Fig 9. FeliCa reader/writer communication diagram
Table 7. Communication overview for FeliCa reader/writer
Communication
direction
FeliCa
FeliCa Higher
transfer speeds
Transfer speed
Modulation on reader side
bit coding
212 kbit/s
424 kbit/s
PN512 card
card PN512
8-30 % ASK
8-30 % ASK
Manchester Coding
(64/13.56) s
Manchester Coding
(32/13.56) s
> 12 % ASK
Bitlength
Loadmodulation on card side > 12 % ASK
bit coding Manchester coding
Manchester coding
The contactless UART of PN512 and a dedicated external host controller are required to
handle the complete FeliCa protocol.
8.3.1 FeliCa framing and coding
Table 8.
FeliCa framing and coding
Preamble
Sync
Len n-Data
CRC
00h 00h 00h 00h 00h 00h B2h 4Dh
To enable the FeliCa communication a 6 byte preamble (00h, 00h, 00h, 00h, 00h, 00h)
and 2 bytes Sync bytes (B2h, 4Dh) are sent to synchronize the receiver.
The following Len byte indicates the length of the sent data bytes plus the LEN byte itself.
The CRC calculation is done according to the FeliCa definitions with the MSB first.
To transmit data on the RF interface, the host controller has to send the Len- and data-
bytes to the PN512's FIFO-buffer. The preamble and the sync bytes are generated by the
PN512 automatically and must not be written to the FIFO by the host controller. The
PN512 performs internally the CRC calculation and adds the result to the data frame.
Example for FeliCa CRC Calculation:
Table 9.
Start value for the CRC Polynomial: (00h), (00h)
Preamble
Sync
Len
03h
2 Data Bytes CRC
ABh CDh 90h
00h
00h
00h
00h
00h
00h
B2h
4Dh
35h
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
16 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
8.4 NFCIP-1 mode
The NFCIP-1 communication differentiates between an active and a Passive
Communication mode.
• Active Communication mode means both the initiator and the target are using their
own RF field to transmit data.
• Passive Communication mode means that the target answers to an initiator command
in a load modulation scheme. The initiator is active in terms of generating the RF field.
• Initiator: generates RF field at 13.56 MHz and starts the NFCIP-1 communication
• Target: responds to initiator command either in a load modulation scheme in Passive
Communication mode or using a self generated and self modulated RF field for Active
Communication mode.
In order to fully support the NFCIP-1 standard the PN512 supports the Active and Passive
Communication mode at the transfer speeds 106 kbit/s, 212 kbit/s and 424 kbit/s as
defined in the NFCIP-1 standard.
BATTERY
MICROCONTROLLER
BATTERY
PN512
PN512
MICROCONTROLLER
001aan215
initiator: active
target:
passive or active
Fig 10. NFCIP-1 mode
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
17 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
8.4.1 Active communication mode
Active communication mode means both the initiator and the target are using their own
RF field to transmit data.
Initial command
host
host
NFC INITIATOR
NFC TARGET
1. initiator starts communication at
selected transfer speed
powered to
powered for
generate RF field
digital processing
response
host
host
NFC INITIATOR
NFC TARGET
2. target answers at
the same transfer speed
powered for digital
processing
powered to
generate RF field
001aan216
Fig 11. Active communication mode
Table 10. Communication overview for Active communication mode
Communication 106 kbit/s
direction
212 kbit/s
424 kbit/s
848 kbit/s
1.69 Mbit/s,
3.39 Mbit/s
Initiator Target According to
According to FeliCa, 8-30 % digital capability to handle
ASK Manchester Coded this communication
ISO/IEC 14443A
Target Initiator
100 % ASK,
Modified
Miller Coded
The contactless UART of PN512 and a dedicated host controller are required to handle
the NFCIP-1 protocol.
Note: Transfer Speeds above 424 kbit/s are not defined in the NFCIP-1 standard. The
PN512 supports these transfer speeds only with dedicated external circuits.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
18 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
8.4.2 Passive communication mode
Passive Communication mode means that the target answers to an initiator command in a
load modulation scheme. The initiator is active meaning generating the RF field.
1. initiator starts communication
at selected transfer speed
host
host
NFC INITIATOR
NFC TARGET
2. targets answers using
load modulated data
at the same transfer speed
powered to
powered for
generate RF field
digital processing
001aan217
Fig 12. Passive communication mode
Table 11. Communication overview for Passive communication mode
Communication 106 kbit/s
direction
212 kbit/s
424 kbit/s
848 kbit/s
1.69 Mbit/s,
3.39 Mbit/s
Initiator Target According to
ISO/IEC 14443A
100 % ASK,
According to FeliCa, 8-30
% ASK Manchester Coded this communication
digital capability to handle
Modified
Miller Coded
Target Initiator According to
ISO/IEC 14443A
According to FeliCa, > 12 %
ASK Manchester Coded
subcarrier load
modulation,
Manchester Coded
The contactless UART of PN512 and a dedicated host controller are required to handle
the NFCIP-1 protocol.
Note: Transfer Speeds above 424 kbit/s are not defined in the NFCIP-1 standard. The
PN512 supports these transfer speeds only with dedicated external circuits.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
19 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
8.4.3 NFCIP-1 framing and coding
The NFCIP-1 framing and coding in Active and Passive Communication mode is defined
in the NFCIP-1 standard.
Table 12. Framing and coding overview
Transfer speed
106 kbit/s
Framing and Coding
According to the ISO/IEC 14443A/MIFARE scheme
According to the FeliCa scheme
According to the FeliCa scheme
212 kbit/s
424 kbit/s
8.4.4 NFCIP-1 protocol support
The NFCIP-1 protocol is not completely described in this document. For detailed
explanation of the protocol refer to the NFCIP-1 standard. However the datalink layer is
according to the following policy:
• Speed shall not be changed while continuum data exchange in a transaction.
• Transaction includes initialization and anticollision methods and data exchange (in
continuous way, meaning no interruption by another transaction).
In order not to disturb current infrastructure based on 13.56 MHz general rules to start
NFCIP-1 communication are defined in the following way.
1. Per default NFCIP-1 device is in Target mode meaning its RF field is switched off.
2. The RF level detector is active.
3. Only if application requires the NFCIP-1 device shall switch to Initiator mode.
4. Initiator shall only switch on its RF field if no external RF field is detected by RF Level
detector during a time of TIDT.
5. The initiator performs initialization according to the selected mode.
8.4.5 MIFARE Card operation mode
Table 13. MIFARE Card operation mode
Communication
direction
ISO/IEC 14443A/
MIFARE
MIFARE Higher transfer speeds
transfer speed 106 kbit/s
212 kbit/s
424 kbit/s
reader/writer Modulation on
100 % ASK
100 % ASK
100 % ASK
PN512
reader side
bit coding
Bitlength
Modified Miller
Modified Miller
Modified Miller
(128/13.56) s
(64/13.56) s
(32/13.56) s
PN512 reader/ Modulation on
subcarrier load
modulation
subcarrier load
modulation
subcarrier load
modulation
writer
PN512 side
subcarrier
frequency
13.56 MHz/16
13.56 MHz/16
13.56 MHz/16
bit coding
Manchester coding
BPSK
BPSK
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
20 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
8.4.6 FeliCa Card operation mode
Table 14. FeliCa Card operation mode
Communication
direction
FeliCa
FeliCa Higher
transfer speeds
Transfer speed
212 kbit/s
424 kbit/s
reader/writer
PN512
Modulation on reader side
bit coding
8-30 % ASK
8-30 % ASK
Manchester Coding
(64/13.56) s
Manchester Coding
(32/13.56) s
Bitlength
PN512 reader/ Load modulation on PN512
> 12 % ASK load
modulation
> 12 % ASK load
modulation
writer
side
bit coding
Manchester coding
Manchester coding
9. PN512 register SET
9.1 PN512 registers overview
Table 15. PN512 registers overview
Addr
(hex)
Register Name Function
Page 0: Command and Status
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
PageReg
Selects the register page
Starts and stops command execution
CommandReg
ComlEnReg
DivlEnReg
Controls bits to enable and disable the passing of Interrupt Requests
Controls bits to enable and disable the passing of Interrupt Requests
Contains Interrupt Request bits
ComIrqReg
DivIrqReg
Contains Interrupt Request bits
ErrorReg
Error bits showing the error status of the last command executed
Contains status bits for communication
Status1Reg
Status2Reg
FIFODataReg
FIFOLevelReg
Contains status bits of the receiver and transmitter
In- and output of 64 byte FIFO-buffer
Indicates the number of bytes stored in the FIFO
WaterLevelReg Defines the level for FIFO under- and overflow warning
ControlReg
BitFramingReg
CollReg
Contains miscellaneous Control Registers
Adjustments for bit oriented frames
Bit position of the first bit collision detected on the RF-interface
Reserved for future use
RFU
Page 1: Command
0
1
2
3
4
5
PageReg
Selects the register page
ModeReg
Defines general modes for transmitting and receiving
Defines the data rate and framing during transmission
Defines the data rate and framing during receiving
Controls the logical behavior of the antenna driver pins TX1 and TX2
Controls the setting of the antenna drivers
TxModeReg
RxModeReg
TxControlReg
TxAutoReg
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
21 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 15. PN512 registers overview …continued
Addr
(hex)
Register Name Function
6
7
8
9
A
B
C
TxSelReg
RxSelReg
Selects the internal sources for the antenna driver
Selects internal receiver settings
RxThresholdReg Selects thresholds for the bit decoder
DemodReg
FelNFC1Reg
FelNFC2Reg
MifNFCReg
Defines demodulator settings
Defines the length of the valid range for the receive package
Defines the length of the valid range for the receive package
Controls the communication in ISO/IEC 14443/MIFARE and NFC
target mode at 106 kbit
D
E
F
ManualRCVReg Allows manual fine tuning of the internal receiver
TypeBReg Configure the ISO/IEC 14443 type B
SerialSpeedReg Selects the speed of the serial UART interface
Page 2: CFG
0
1
2
3
PageReg
Selects the register page
CRCResultReg
Shows the actual MSB and LSB values of the CRC calculation
GsNOffReg
Selects the conductance of the antenna driver pins TX1 and TX2 for
modulation, when the driver is switched off
4
5
6
7
ModWidthReg
Controls the setting of the ModWidth
TxBitPhaseReg Adjust the TX bit phase at 106 kbit
RFCfgReg
GsNOnReg
Configures the receiver gain and RF level
Selects the conductance of the antenna driver pins TX1 and TX2 for
modulation when the drivers are switched on
8
9
CWGsPReg
ModGsPReg
Selects the conductance of the antenna driver pins TX1 and TX2 for
modulation during times of no modulation
Selects the conductance of the antenna driver pins TX1 and TX2 for
modulation during modulation
A
B
C
D
E
F
TModeReg
TPrescalerReg
Defines settings for the internal timer
TReloadReg
Describes the 16-bit timer reload value
TCounterValReg Shows the 16-bit actual timer value
Page 3: TestRegister
0
1
2
3
PageReg
selects the register page
TestSel1Reg
TestSel2Reg
TestPinEnReg
General test signal configuration
General test signal configuration and PRBS control
Enables pin output driver on 8-bit parallel bus (Note: For serial
interfaces only)
4
TestPin
Defines the values for the 8-bit parallel bus when it is used as I/O bus
ValueReg
5
6
TestBusReg
AutoTestReg
Shows the status of the internal testbus
Controls the digital selftest
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
22 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 15. PN512 registers overview …continued
Addr
(hex)
Register Name Function
7
VersionReg
AnalogTestReg
TestDAC1Reg
TestDAC2Reg
TestADCReg
RFT
Shows the version
Controls the pins AUX1 and AUX2
8
9
Defines the test value for the TestDAC1
Defines the test value for the TestDAC2
Shows the actual value of ADC I and Q
Reserved for production tests
A
B
C-F
9.1.1 Register bit behavior
Depending on the functionality of a register, the access conditions to the register can vary.
In principle bits with same behavior are grouped in common registers. In Table 16 the
access conditions are described.
Table 16. Behavior of register bits and its designation
Abbreviation Behavior
Description
r/w
read and write These bits can be written and read by the -Controller. Since they
are used only for control means, there content is not influenced by
internal state machines, e.g. the PageSelect-Register may be
written and read by the -Controller. It will also be read by internal
state machines, but never changed by them.
dy
r
dynamic
These bits can be written and read by the -Controller.
Nevertheless, they may also be written automatically by internal
state machines, e.g. the Command-Register changes its value
automatically after the execution of the actual command.
read only
These registers hold bits, which value is determined by internal
states only, e.g. the CRCReady bit can not be written from
external but shows internal states.
w
write only
-
Reading these registers returns always ZERO.
These registers are reserved for future use.
RFU
In case of a PN512 Version version 2.0 (VersionReg = 82h) a
read access to these registers returns always the value “0”.
Nevertheless this is not guaranteed for future chips versions
where the value is undefined. In case of a write access, it is
recommended to write always the value “0”.
RFT
-
These registers are reserved for production tests and shall not be
changed.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
23 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2 Register description
9.2.1 Page 0: Command and status
9.2.1.1 PageReg
Selects the register page.
Table 17. PageReg register (address 00h); reset value: 00h, 0000000b
7
UsePage Select
r/w
6
0
5
0
4
0
3
0
2
0
1
0
PageSelect
r/w r/w
Access
Rights
RFU
RFU
RFU
RFU
RFU
Table 18. Description of PageReg bits
Bit
Symbol
Description
7
UsePageSelect Set to logic 1, the value of PageSelect is used as register address A5
and A4. The LSB-bits of the register address are defined by the
address pins or the internal address latch, respectively.
Set to logic 0, the whole content of the internal address latch defines
the register address. The address pins are used as described in
Section 10.1 “Automatic microcontroller interface detection”.
6 to 2
1 to 0
-
Reserved for future use.
PageSelect
The value of PageSelect is used only if UsePageSelect is set to
logic 1. In this case it specifies the register page (which is A5 and A4
of the register address).
9.2.1.2 CommandReg
Starts and stops command execution.
Table 19. CommandReg register (address 01h); reset value: 20h, 00100000b
7
0
6
0
5
4
3
2
1
0
RcvOff Power Down
r/w dy
Command
Access
Rights
RFU
RFU
dy
dy
dy
dy
Table 20. Description of CommandReg bits
Bit
7 to 6
5
Symbol
-
Description
Reserved for future use.
RcvOff
PowerDown
Set to logic 1, the analog part of the receiver is switched off.
Set to logic 1, Soft Power-down mode is entered.
4
Set to logic 0, the PN512 starts the wake up procedure. During this
procedure this bit still shows a 1. A 0 indicates that the PN512 is ready
for operations; see Section 16.2 “Soft power-down mode”.
Note: The bit Power Down cannot be set, when the command
SoftReset has been activated.
3 to 0
Command
Activates a command according to the Command Code. Reading this
register shows, which command is actually executed (see Section 19.3
“PN512 command overview”).
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
24 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.3 CommIEnReg
Control bits to enable and disable the passing of interrupt requests.
Table 21. CommIEnReg register (address 02h); reset value: 80h, 10000000b
7
6
5
4
3
2
1
0
IRqInv
r/w
TxIEn
r/w
RxIEn
r/w
IdleIEn HiAlertIEn LoAlertIEn ErrIEn TimerIEn
r/w r/w r/w r/w r/w
Access
Rights
Table 22. Description of CommIEnReg bits
Bit
Symbol
Description
7
IRqInv
Set to logic 1, the signal on pin IRQ is inverted with respect to bit IRq in the
register Status1Reg. Set to logic 0, the signal on pin IRQ is equal to bit IRq.
In combination with bit IRqPushPull in register DivIEnReg, the default value
of 1 ensures, that the output level on pin IRQ is 3-state.
6
5
4
3
2
1
0
TxIEn
RxIEn
IdleIEn
Allows the transmitter interrupt request (indicated by bit TxIRq) to be
propagated to pin IRQ.
Allows the receiver interrupt request (indicated by bit RxIRq) to be
propagated to pin IRQ.
Allows the idle interrupt request (indicated by bit IdleIRq) to be propagated to
pin IRQ.
HiAlertIEn Allows the high alert interrupt request (indicated by bit HiAlertIRq) to be
propagated to pin IRQ.
LoAlertIEn Allows the low alert interrupt request (indicated by bit LoAlertIRq) to be
propagated to pin IRQ.
ErrIEn
Allows the error interrupt request (indicated by bit ErrIRq) to be propagated
to pin IRQ.
TimerIEn
Allows the timer interrupt request (indicated by bit TimerIRq) to be
propagated to pin IRQ.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
25 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.4 DivIEnReg
Control bits to enable and disable the passing of interrupt requests.
Table 23. DivIEnReg register (address 03h); reset value: 00h, 00000000b
7
IRQPushPull
r/w
6
5
4
3
2
1
0
0
0
SiginActIEn ModeIEn CRCIEn RFOnIEn RFOffIEn
r/w r/w r/w r/w r/w
Access
Rights
RFU RFU
Table 24. Description of DivIEnReg bits
Bit
Symbol
Description
7
IRQPushPull
Set to logic 1, the pin IRQ works as standard CMOS output pad.
Set to logic 0, the pin IRQ works as open drain output pad.
Reserved for future use.
6 to 5
-
4
3
SiginActIEn
ModeIEn
Allows the SIGIN active interrupt request to be propagated to pin IRQ.
Allows the mode interrupt request (indicated by bit ModeIRq) to be
propagated to pin IRQ.
2
1
0
CRCIEn
RfOnIEn
RfOffIEn
Allows the CRC interrupt request (indicated by bit CRCIRq) to be
propagated to pin IRQ.
Allows the RF field on interrupt request (indicated by bit RfOnIRq) to
be propagated to pin IRQ.
Allows the RF field off interrupt request (indicated by bit RfOffIRq) to
be propagated to pin IRQ.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
26 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.5 CommIRqReg
Contains Interrupt Request bits.
Table 25. CommIRqReg register (address 04h); reset value: 14h, 00010100b
7
Set1
w
6
5
4
3
2
1
0
TxIRq
dy
RxIRq
dy
IdleIRq HiAlertIRq LoAlertIRq ErrIRq TimerIRq
dy dy dy dy dy
Access
Rights
Table 26. Description of CommIRqReg bits
All bits in the register CommIRqReg shall be cleared by software.
Bit Symbol Description
7
Set1
Set to logic 1, Set1 defines that the marked bits in the register CommIRqReg
are set.
Set to logic 0, Set1 defines, that the marked bits in the register CommIRqReg
are cleared.
6
5
TxIRq
RxIRq
Set to logic 1 immediately after the last bit of the transmitted data was sent out.
Set to logic 1 when the receiver detects the end of a valid datastream.
If the bit RxNoErr in register RxModeReg is set to logic 1, bit RxIRq is only set
to logic 1 when data bytes are available in the FIFO.
4
IdleIRq
Set to logic 1, when a command terminates by itself e.g. when the
CommandReg changes its value from any command to the Idle Command.
If an unknown command is started, the CommandReg changes its content to
the idle state and the bit IdleIRq is set. Starting the Idle Command by the
-Controller does not set bit IdleIRq.
3
2
HiAlertIRq Set to logic 1, when bit HiAlert in register Status1Reg is set. In opposition to
HiAlert, HiAlertIRq stores this event and can only be reset as indicated by bit
Set1.
LoAlertIRq Set to logic 1, when bit LoAlert in register Status1Reg is set. In opposition to
LoAlert, LoAlertIRq stores this event and can only be reset as indicated by bit
Set1.
1
0
ErrIRq
Set to logic 1 if any error bit in the Error Register is set.
TimerIRq
Set to logic 1 when the timer decrements the TimerValue Register to zero.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
27 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.6 DivIRqReg
Contains Interrupt Request bits
Table 27. DivIRqReg register (address 05h); reset value: XXh, 000X00XXb
7
Set2
w
6
0
5
0
4
3
2
1
0
SiginActIRq ModeIRq CRCIRq RFOnIRq RFOffIRq
dy dy dy dy dy
Access
Rights
RFU
RFU
Table 28. Description of DivIRqReg bits
All bits in the register DivIRqReg shall be cleared by software.
Bit
Symbol
Description
7
Set2
Set to logic 1, Set2 defines that the marked bits in the register
DivIRqReg are set.
Set to logic 0, Set2 defines, that the marked bits in the register
DivIRqReg are cleared
6 to 5
4
-
Reserved for future use.
SiginActIRq
Set to logic 1, when SIGIN is active. See Section 12.6 “S2C interface
support”. This interrupt is set when either a rising or falling signal edge
is detected.
3
ModeIRq
Set to logic 1, when the mode has been detected by the Data mode
detector.
Note: The Data mode detector can only be activated by the AutoColl
command and is terminated automatically having detected the
Communication mode.
Note: The Data mode detector is automatically restarted after each RF
Reset.
2
CRCIRq
Set to logic 1, when the CRC command is active and all data are
processed.
1
0
RFOnIRq
RFOffIRq
Set to logic 1, when an external RF field is detected.
Set to logic 1, when a present external RF field is switched off.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
28 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.7 ErrorReg
Error bit register showing the error status of the last command executed.
Table 29. ErrorReg register (address 06h); reset value: 00h, 00000000b
7
WrErr
r
6
5
4
3
2
1
0
TempErr RFErr BufferOvfl CollErr CRCErr ParityErr ProtocolErr
Access
Rights
r
r
r
r
r
r
r
Table 30. Description of ErrorReg bits
Bit
Symbol
Description
7
WrErr
Set to logic 1, when data is written into FIFO by the host controller
during the AutoColl command or MFAuthent command or if data is
written into FIFO by the host controller during the time between
sending the last bit on the RF interface and receiving the last bit on the
RF interface.
6
5
TempErr[1]
RFErr
Set to logic 1, if the internal temperature sensor detects overheating.
In this case, the antenna drivers are switched off automatically.
Set to logic 1, if in Active Communication mode the counterpart does
not switch on the RF field in time as defined in NFCIP-1 standard.
Note: RFErr is only used in Active Communication mode. The bits
RxFraming or the bits TxFraming has to be set to 01 to enable this
functionality.
4
3
BufferOvfl
CollErr
Set to logic 1, if the host controller or a PN512’s internal state machine
(e.g. receiver) tries to write data into the FIFO-bufferFIFO-buffer
although the FIFO-buffer is already full.
Set to logic 1, if a bit-collision is detected. It is cleared automatically at
receiver start-up phase. This bit is only valid during the bitwise
anticollision at 106 kbit. During communication schemes at 212 and
424 kbit this bit is always set to logic 1.
2
1
0
CRCErr
Set to logic 1, if bit RxCRCEn in register RxModeReg is set and the
CRC calculation fails. It is cleared to 0 automatically at receiver
start-up phase.
ParityErr
ProtocolErr
Set to logic 1, if the parity check has failed. It is cleared automatically
at receiver start-up phase. Only valid for ISO/IEC 14443A/MIFARE or
NFCIP-1 communication at 106 kbit.
Set to logic 1, if one out of the following cases occur:
• Set to logic 1 if the SOF is incorrect. It is cleared automatically at
receiver start-up phase. The bit is only valid for 106 kbit in Active
and Passive Communication mode.
• If bit DetectSync in register ModeReg is set to logic 1 during
FeliCa communication or active communication with transfer
speeds higher than 106 kbit, the bit ProtocolErr is set to logic 1 in
case of a byte length violation.
• During the AutoColl command, bit ProtocolErr is set to logic 1, if
the bit Initiator in register ControlReg is set to logic 1.
• During the MFAuthent Command, bit ProtocolErr is set to logic 1,
if the number of bytes received in one data stream is incorrect.
• Set to logic 1, if the Miller Decoder detects 2 pulses below the
minimum time according to the ISO/IEC 14443A definitions.
[1] Command execution will clear all error bits except for bit TempErr. A setting by software is impossible.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
29 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.8 Status1Reg
Contains status bits of the CRC, Interrupt and FIFO-buffer.
Table 31. Status1Reg register (address 07h); reset value: XXh, X100X01Xb
7
6
5
4
IRq
r
3
2
1
HiAlert
r
0
LoAlert
r
RFFreqOK CRCOk CRCReady
TRunning RFOn
Access
Rights
r
r
r
r
r
Table 32. Description of Status1Reg bits
Bit
Symbol
Description
7
RFFreqOK
Indicates if the frequency detected at the RX pin is in the range of
13.56 MHz.
Set to logic 1, if the frequency at the RX pin is in the range
12 MHz < RX pin frequency < 15 MHz.
Note: The value of RFFreqOK is not defined if the external RF
frequency is in the range from 9 to 12 MHz or in the range from
15 to 19 MHz.
6
CRCOk
Set to logic 1, if the CRC Result is zero. For data transmission and
reception the bit CRCOk is undefined (use CRCErr in register
ErrorReg). CRCOk indicates the status of the CRC co-processor,
during calculation the value changes to ZERO, when the calculation is
done correctly, the value changes to ONE.
5
4
3
CRCReady
IRq
Set to logic 1, when the CRC calculation has finished. This bit is only
valid for the CRC co-processor calculation using the command
CalcCRC.
This bit shows, if any interrupt source requests attention (with respect
to the setting of the interrupt enable bits, see register CommIEnReg
and DivIEnReg).
TRunning
Set to logic 1, if the PN512’s timer unit is running, e.g. the timer will
decrement the TCounterValReg with the next timer clock.
Note: In the gated mode the bit TRunning is set to logic 1, when the
timer is enabled by the register bits. This bit is not influenced by the
gated signal.
2
1
RFOn
Set to logic 1, if an external RF field is detected. This bit does not store
the state of the RF field.
HiAlert
Set to logic 1, when the number of bytes stored in the FIFO-buffer
fulfills the following equation:
HiAlert = 64 – FIFOLength WaterLevel
Example:
FIFOLength = 60, WaterLevel = 4 HiAlert = 1
FIFOLength = 59, WaterLevel = 4 HiAlert = 0
0
LoAlert
Set to logic 1, when the number of bytes stored in the FIFO-buffer
fulfills the following equation: LoAlert = FIFOLength WaterLevel
Example:
FIFOLength = 4, WaterLevel = 4 LoAlert = 1
FIFOLength = 5, WaterLevel = 4 LoAlert = 0
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
30 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.9 Status2Reg
Contains status bits of the Receiver, Transmitter and Data mode detector.
Table 33. Status2Reg register (address 08h); reset value: 00h, 00000000b
7
6
5
0
4
3
2
1
0
TempSensClear I2CForceHS
TargetActivated MFCrypto1On Modem State
dy dy
Access
Rights
r/w r/w
RFU
r
r
r
Table 34. Description of Status2Reg bits
Bit
Symbol
Description
7
TempSensClear Set to logic 1, this bit clears the temperature error, if the temperature
is below the alarm limit of 125 C.
6
I2CForceHS
I2C input filter settings. Set to logic 1, the I2C input filter is set to the
High-speed mode independent of the I2C protocol. Set to logic 0, the
I2C input filter is set to the used I2C protocol.
5
4
-
Reserved for future use.
TargetActivated
Set to logic 1 if the Select command or if the Polling command was
answered. Note: This bit can only be set during the AutoColl
command in Passive Communication mode.
Note: This bit is cleared automatically by switching off the external
RF field.
3
MFCrypto1On
Modem State
This bit indicates that the MIFARE Crypto1 unit is switched on and
therefore all data communication with the card is encrypted.
This bit can only be set to logic 1 by a successful execution of the
MFAuthent Command. This bit is only valid in Reader/Writer mode
for MIFARE cards. This bit shall be cleared by software.
2 to 0
ModemState shows the state of the transmitter and receiver state
machines.
Value Description
000
001
010
IDLE
Wait for StartSend in register BitFramingReg
TxWait: Wait until RF field is present, if the bit TxWaitRF is
set to logic 1. The minimum time for TxWait is defined by the
TxWaitReg register.
011
100
Sending
RxWait: Wait until RF field is present, if the bit RxWaitRF is
set to logic 1. The minimum time for RxWait is defined by the
RxWaitReg register.
101
110
Wait for data
Receiving
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
31 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.10 FIFODataReg
In- and output of 64 byte FIFO-buffer.
Table 35. FIFODataReg register (address 09h); reset value: XXh, XXXXXXXXb
7
6
5
4
3
2
1
0
FIFOData
Access
Rights
dy
dy
dy
dy
dy
dy
dy
dy
Table 36. Description of FIFODataReg bits
Bit
Symbol
Description
7 to 0
FIFOData
Data input and output port for the internal 64 byte FIFO-buffer. The
FIFO-buffer acts as parallel in/parallel out converter for all serial data
stream in- and outputs.
9.2.1.11 FIFOLevelReg
Indicates the number of bytes stored in the FIFO.
Table 37. FIFOLevelReg register (address 0Ah); reset value: 00h, 00000000b
7
FlushBuffer
w
6
5
4
3
2
1
0
FIFOLevel
r
Access
Rights
r
r
r
r
r
r
Table 38. Description of FIFOLevelReg bits
Bit
Symbol
Description
7
FlushBuffer
Set to logic 1, this bit clears the internal FIFO-buffer’s read- and
write-pointer and the bit BufferOvfl in the register ErrReg immediately.
Reading this bit will always return 0.
6 to 0
FIFOLevel
Indicates the number of bytes stored in the FIFO-buffer. Writing to the
FIFODataReg increments, reading decrements the FIFOLevel.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
32 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.12 WaterLevelReg
Defines the level for FIFO under- and overflow warning.
Table 39. WaterLevelReg register (address 0Bh); reset value: 08h, 00001000b
7
0
6
0
5
4
3
2
1
0
WaterLevel
Access
Rights
RFU
RFU
r/w
r/w
r/w
r/w
r/w
r/w
Table 40. Description of WaterLevelReg bits
Bit
Symbol
Description
7 to 6
5 to 0
-
Reserved for future use.
WaterLevel
This register defines a warning level to indicate a FIFO-buffer over- or
underflow:
The bit HiAlert in Status1Reg is set to logic 1, if the remaining number
of bytes in the FIFO-buffer space is equal or less than the defined
number of WaterLevel bytes.
The bit LoAlert in Status1Reg is set to logic 1, if equal or less than
WaterLevel bytes are in the FIFO.
Note: For the calculation of HiAlert and LoAlert see Table 31
9.2.1.13 ControlReg
Miscellaneous control bits.
Table 41. ControlReg register (address 0Ch); reset value: 00h, 00000000b
7
6
5
4
3
0
2
1
0
TStopNow TStartNow WrNFCIDtoFIFO Initiator
dy r/w
RxLastBits
r
Access
Rights
w
w
RFU
r
r
Table 42. Description of ControlReg bits
Bit
Symbol
Description
7
TStopNow
Set to logic 1, the timer stops immediately.
Reading this bit will always return 0.
Set to logic 1 starts the timer immediately.
Reading this bit will always return 0.
6
5
TStartNow
WrNFCIDtoFIFO Set to logic 1, the internal stored NFCID (10 bytes) is copied into the
FIFO.
Afterwards the bit is cleared automatically
4
3
Initiator
-
Set to logic 1, the PN512 acts as initiator, otherwise it acts as target
Reserved for future use.
2 to 0 RxLastBits
Shows the number of valid bits in the last received byte. If zero, the
whole byte is valid.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
33 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.14 BitFramingReg
Adjustments for bit oriented frames.
Table 43. BitFramingReg register (address 0Dh); reset value: 00h, 00000000b
7
StartSend
w
6
5
4
3
0
2
1
TxLastBits
r/w
0
RxAlign
r/w
Access
Rights
r/w
r/w
RFU
r/w
r/w
Table 44. Description of BitFramingReg bits
Bit
Symbol
StartSend Set to logic 1, the transmission of data starts.
This bit is only valid in combination with the Transceive command.
Description
7
6 to 4
RxAlign
Used for reception of bit oriented frames: RxAlign defines the bit position
for the first bit received to be stored in the FIFO. Further received bits are
stored at the following bit positions.
Example:
RxAlign = 0: the LSB of the received bit is stored at bit 0, the second
received bit is stored at bit position 1.
RxAlign = 1: the LSB of the received bit is stored at bit 1, the second
received bit is stored at bit position 2.
RxAlign = 7: the LSB of the received bit is stored at bit 7, the second
received bit is stored in the following byte at bit position 0.
This bit shall only be used for bitwise anticollision at 106 kbit/s in Passive
Communication mode. In all other modes it shall be set to logic 0.
3
-
Reserved for future use.
2 to 0
TxLastBits Used for transmission of bit oriented frames: TxLastBits defines the
number of bits of the last byte that shall be transmitted. A 000 indicates
that all bits of the last byte shall be transmitted.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
34 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.1.15 CollReg
Defines the first bit collision detected on the RF interface.
Table 45. CollReg register (address 0Eh); reset value: XXh, 101XXXXXb
7
6
5
4
3
2
1
0
Values
AfterColl
0
CollPos
NotValid
CollPos
Access
Rights
r/w
RFU
r
r
r
r
r
r
Table 46. Description of CollReg bits
Bit
Symbol
Description
7
ValuesAfterColl If this bit is set to logic 0, all receiving bits will be cleared after a
collision. This bit shall only be used during bitwise anticollision at
106 kbit, otherwise it shall be set to logic 1.
6
5
-
Reserved for future use.
CollPosNotValid Set to logic 1, if no Collision is detected or the Position of the
Collision is out of the range of bits CollPos. This bit shall only be
interpreted in Passive Communication mode at 106 kbit or
ISO/IEC 14443A/MIFARE Reader/Writer mode.
4 to 0
CollPos
These bits show the bit position of the first detected collision in a
received frame, only data bits are interpreted.
Example:
00h indicates a bit collision in the 32th bit
01h indicates a bit collision in the 1st bit
08h indicates a bit collision in the 8th bit
These bits shall only be interpreted in Passive Communication mode
at 106 kbit or ISO/IEC 14443A/MIFARE Reader/Writer mode if bit
CollPosNotValid is set to logic 0.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
35 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2 Page 1: Communication
9.2.2.1 PageReg
Selects the register page.
Table 47. PageReg register (address 10h); reset value: 00h, 00000000b
7
UsePage Select
r/w
6
0
5
0
4
0
3
0
2
0
1
0
PageSelect
r/w r/w
Access
Rights
RFU
RFU
RFU
RFU
RFU
Table 48. Description of PageReg bits
Bit
Symbol
Description
7
UsePage Select Set to logic 1, the value of PageSelect is used as register address A5
and A4. The LSB-bits of the register address are defined by the
address pins or the internal address latch, respectively.
Set to logic 0, the whole content of the internal address latch defines
the register address. The address pins are used as described in
Section 10.1 “Automatic microcontroller interface detection”.
6 to 2
1 to 0
-
Reserved for future use.
PageSelect
The value of PageSelect is used only, if UsePageSelect is set to
logic 1. In this case it specifies the register page (which is A5 and A4
of the register address).
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
36 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.2 ModeReg
Defines general mode settings for transmitting and receiving.
Table 49. ModeReg register (address 11h); reset value: 3Bh, 00111011b
7
6
5
4
3
2
1
0
MSBFirst Detect Sync TxWaitRF RxWaitRF PolSigin ModeDetOff CRCPreset
r/w r/w r/w r/w r/w r/w r/w r/w
Access
Rights
Table 50. Description of ModeReg bits
Bit
Symbol
Description
7
MSBFirst
Set to logic 1, the CRC co-processor calculates the CRC with MSB
first and the CRCResultMSB and the CRCResultLSB in the
CRCResultReg register are bit reversed.
Note: During RF communication this bit is ignored.
6
Detect Sync
If set to logic 1, the contactless UART waits for the value F0h before
the receiver is activated and F0h is added as a Sync-byte for
transmission.
This bit is only valid for 106 kbit during NFCIP-1 data exchange
protocol.
In all other modes it shall be set to logic 0.
5
4
TxWaitRF
RxWaitRF
Set to logic 1 the transmitter in reader/writer or initiator mode for
NFCIP-1 can only be started, if an RF field is generated.
Set to logic 1, the counter for RxWait starts only if an external RF field
is detected in Target mode for NFCIP-1 or in Card Communication
mode.
3
PolSigin
PolSigin defines the polarity of the SIGIN pin. Set to logic 1, the
polarity of SIGIN pin is active high. Set to logic 0 the polarity of SIGIN
pin is active low.
Note: The internal envelope signal is coded active low.
Note: Changing this bit will generate a SiginActIRq event.
Set to logic 1, the internal mode detector is switched off.
Note: The mode detector is only active during the AutoColl command.
2
ModeDetOff
CRCPreset
1 to 0
Defines the preset value for the CRC co-processor for the command
CalCRC.
Note: During any communication, the preset values is selected
automatically according to the definition in the bits RxMode and
TxMode.
Value
00
Description
0000
01
6363
10
A671
11
FFFF
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
37 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.3 TxModeReg
Defines the data rate and framing during transmission.
Table 51. TxModeReg register (address 12h); reset value: 00h, 00000000b
7
6
5
TxSpeed
dy
4
3
2
1
0
TxCRCEn
r/w
InvMod
r/w
TxMix
r/w
TxFraming
Access
Rights
dy
dy
dy
dy
Table 52. Description of TxModeReg bits
Bit
Symbol
Description
7
TxCRCEn
Set to logic 1, this bit enables the CRC generation during data
transmission.
Note: This bit shall only be set to logic 0 at 106 kbit.
Defines the bit rate while data transmission.
6 to 4
TxSpeed
Value
000
001
010
011
100
101
110
111
Description
106 kbit
212 kbit
424 kbit
848 kbit
1696 kbit
3392 kbit
Reserved
Reserved
Note: The bit coding for transfer speeds above 424 kbit is equivalent to
the bit coding of Active Communication mode 424 kbit (Ecma 340).
3
2
InvMod
TxMix
Set to logic 1, the modulation for transmitting data is inverted.
Set to logic 1, the signal at pin SIGIN is mixed with the internal coder
(see Section 12.6 “S2C interface support”).
1 to 0
TxFraming
Defines the framing used for data transmission.
Value
Description
00
ISO/IEC 14443A/MIFARE and Passive Communication mode
106 kbit
01
10
11
Active Communication mode
FeliCa and Passive communication mode 212 and 424 kbit
ISO/IEC 14443B
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
38 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.4 RxModeReg
Defines the data rate and framing during reception.
Table 53. RxModeReg register (address 13h); reset value: 00h, 00000000b
7
6
5
RxSpeed
dy
4
3
2
1
0
RxCRCEn
r/w
RxNoErr RxMultiple
r/w r/w
RxFraming
Access
Rights
dy
dy
dy
dy
Table 54. Description of RxModeReg bits
Bit
Symbol
Description
7
RxCRCEn
Set to logic 1, this bit enables the CRC calculation during reception.
Note: This bit shall only be set to logic 0 at 106 kbit.
Defines the bit rate while data transmission.
6 to 4
RxSpeed
The PN512’s analog part handles only transfer speeds up to 424 kbit
internally, the digital UART handles the higher transfer speeds as well.
Value
000
001
010
011
100
101
110
111
Description
106 kbit
212 kbit
424 kbit
848 kbit
1696 kbit
3392 kbit
Reserved
Reserved
Note: The bit coding for transfer speeds above 424 kbit is equivalent to
the bit coding of Active Communication mode 424 kbit (Ecma 340).
3
2
RxNoErr
If set to logic 1 a not valid received data stream (less than 4 bits
received) will be ignored. The receiver will remain active.
For ISO/IEC14443B also RxSOFReq logic 1 is required to ignore a non
valid datastream.
RxMultiple
Set to logic 0, the receiver is deactivated after receiving a data frame.
Set to logic 1, it is possible to receive more than one data frame. Having
set this bit, the receive and transceive commands will not terminate
automatically. In this case the multiple receiving can only be deactivated
by writing any command (except the Receive command) to the
CommandReg register or by clearing the bit by the host controller.
At the end of a received data stream an error byte is added to the FIFO.
The error byte is a copy of the ErrorReg register.
The behaviour for version 1.0 is described in Section 21 “Errata sheet”
on page 109.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
39 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 54. Description of RxModeReg bits
Bit
Symbol
Description
Defines the expected framing for data reception.
1 to 0
RxFraming
Value
Description
00
ISO/IEC 14443A/MIFARE and Passive Communication
mode 106 kbit
01
10
11
Active Communication mode
FeliCa and Passive Communication mode 212 and 424 kbit
ISO/IEC 14443B
9.2.2.5 TxControlReg
Controls the logical behavior of the antenna driver pins Tx1 and Tx2.
Table 55. TxControlReg register (address 14h); reset value: 80h, 10000000b
7
6
5
4
3
2
1
0
InvTx2RF InvTx1RF InvTx2RF InvTx1RF Tx2CW CheckRF Tx2RF Tx1RF
On
On
Off
Off
En
En
Access
Rights
r/w
r/w
r/w
r/w
r/w
w
r/w
r/w
Table 56. Description of TxControlReg bits
Bit
Symbol
Description
7
InvTx2RFOn
Set to logic 1, the output signal at pin TX2 will be inverted, if driver TX2
is enabled.
6
5
4
3
InvTx1RFOn
InvTx2RFOff
InvTx1RFOff
Tx2CW
Set to logic 1, the output signal at pin TX1 will be inverted, if driver TX1
is enabled.
Set to logic 1, the output signal at pin TX2 will be inverted, if driver TX2
is disabled.
Set to logic 1, the output signal at pin TX1 will be inverted, if driver TX1
is disabled.
Set to logic 1, the output signal on pin TX2 will deliver continuously the
un-modulated 13.56 MHz energy carrier.
Set to logic 0, Tx2CW is enabled to modulate the 13.56 MHz energy
carrier.
2
CheckRF
Set to logic 1, Tx2RFEn and Tx1RFEn can not be set if an external RF
field is detected. Only valid when using in combination with bit
Tx2RFEn or Tx1RFEn
1
0
Tx2RFEn
Tx1RFEn
Set to logic 1, the output signal on pin TX2 will deliver the 13.56 MHz
energy carrier modulated by the transmission data.
Set to logic 1, the output signal on pin TX1 will deliver the 13.56 MHz
energy carrier modulated by the transmission data.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
40 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.6 TxAutoReg
Controls the settings of the antenna driver.
Table 57. TxAutoReg register (address 15h); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
AutoRF Force100
Auto
0
CAOn InitialRF Tx2RFAut Tx1RFAuto
OFF
ASK
WakeUp
On
oEn
En
Access
Rights
r/w
r/w
r/w
RFU
r/w
r/w
r/w
r/w
Table 58. Description of TxAutoReg bits
Bit
Symbol
Description
7
AutoRFOFF
Set to logic 1, all active antenna drivers are switched off after the last
data bit has been transmitted as defined in the NFCIP-1.
6
5
Force100ASK Set to logic 1, Force100ASK forces a 100% ASK modulation
independent of the setting in register ModGsPReg.
AutoWakeUp Set to logic 1, the PN512 in soft Power-down mode will be started by
the RF level detector.
4
3
-
Reserved for future use.
CAOn
Set to logic 1, the collision avoidance is activated and internally the
value n is set in accordance to the NFCIP-1 Standard.
2
InitialRFOn
Set to logic 1, the initial RF collision avoidance is performed and the bit
InitialRFOn is cleared automatically, if the RF is switched on.
Note: The driver, which should be switched on, has to be enabled by
bit Tx2RFAutoEn or bit Tx1RFAutoEn.
1
Tx2RFAutoEn Set to logic 1, the driver Tx2 is switched on after the external RF field
is switched off according to the time TADT. If the bits InitialRFOn and
Tx2RFAutoEn are set to logic 1, Tx2 is switched on if no external RF
field is detected during the time TIDT.
Note: The times TADT and TIDT are defined in the NFC IP-1 standard
(ISO/IEC 18092).
0
Tx1RFAutoEn Set to logic 1, the driver Tx1 is switched on after the external RF field
is switched off according to the time TADT. If the bit InitialRFOn and
Tx1RFAutoEn are set to logic 1, Tx1 is switched on if no external RF
field is detected during the time TIDT.
Note: The times TADT and TIDT are defined in the NFC IP-1 standard
(ISO/IEC 18092).
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
41 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.7 TxSelReg
Selects the sources for the analog part.
Table 59. TxSelReg register (address 16h); reset value: 10h, 00010000b
7
0
6
0
5
4
3
2
1
0
DriverSel
SigOutSel
Access
Rights
RFU
RFU
r/w
r/w
r/w
r/w
r/w
r/w
Table 60. Description of TxSelReg bits
Bit
Symbol
Description
Reserved for future use.
Selects the input of driver Tx1 and Tx2.
7 to 6
-
5 to 4 DriverSel
Value
Description
00
Tristate
Note: In soft power down the drivers are only in Tristate mode
if DriverSel is set to Tristate mode.
01
10
11
Modulation signal (envelope) from the internal coder
Modulation signal (envelope) from SIGIN
HIGH
Note: The HIGH level depends on the setting of InvTx1RFOn/
InvTx1RFOff and InvTx2RFOn/InvTx2RFOff.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
42 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 60. Description of TxSelReg bits …continued
Bit Symbol Description
3 to 0 SigOutSel Selects the input for the SIGOUT Pin.
Value
0000
0001
0010
0011
Description
Tristate
Low
High
TestBus signal as defined by bit TestBusBitSel in register
TestSel1Reg.
0100
0101
0110
Modulation signal (envelope) from the internal coder
Serial data stream to be transmitted
Output signal of the receiver circuit (card modulation signal
regenerated and delayed). This signal is used as data output
signal for SAM interface connection using 3 lines.
Note: To have a valid signal the PN512 has to be set to the
receiving mode by either the Transceive or Receive
command. The bit RxMultiple can be used to keep the PN512
in receiving mode.
Note: Do not use this setting in MIFARE mode. Manchester
coding as data collisions will not be transmitted on the
SIGOUT line.
0111
Serial data stream received.
Note: Do not use this setting in MIFARE mode. Miller coding
parameters as the bit length can vary.
1000-1011 FeliCa Sam modulation
1000 RX*
1001 TX
1010 Demodulator comparator output
1011 RFU
Note: * To have a valid signal the PN512 has to be set to the
receiving mode by either the Transceive or Receive
command. The bit RxMultiple can be used to keep the PN512
in receiving mode.
1100-1111 MIFARE Sam modulation
1100 RX* with RF carrier
1101 TX with RF carrier
1110 RX with RF carrier un-filtered
1111 RX envelope un-filtered
Note: *To have a valid signal the PN512 has to be set to the
receiving mode by either the Transceive or Receive
command. The bit RxMultiple can be used to keep the PN512
in receiving mode.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
43 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.8 RxSelReg
Selects internal receiver settings.
Table 61. RxSelReg register (address 17h); reset value: 84h, 10000100b
7
6
5
4
3
2
1
0
UartSel
RxWait
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Table 62. Description of RxSelReg bits
Bit
Symbol
Description
Selects the input of the contactless UART
7 to 6
UartSel
Value
00
Description
Constant Low
01
Envelope signal at SIGIN
10
Modulation signal from the internal analog part
11
Modulation signal from SIGIN pin. Only valid for transfer
speeds above 424 kbit
5 to 0
RxWait
After data transmission, the activation of the receiver is delayed for
RxWait bit-clocks. During this ‘frame guard time’ any signal at pin RX
is ignored. This parameter is ignored by the Receive command. All
other commands (e.g. Transceive, Autocoll, MFAuthent) use this
parameter. Depending on the mode of the PN512, the counter starts
different. In Passive Communication mode the counter starts with the
last modulation pulse of the transmitted data stream. In Active
Communication mode the counter starts immediately after the external
RF field is switched on.
9.2.2.9 RxThresholdReg
Selects thresholds for the bit decoder.
Table 63. RxThresholdReg register (address 18h); reset value: 84h, 10000100b
7
6
5
4
3
0
2
1
0
MinLevel
CollLevel
r/w
Access
Rights
r/w
r/w
r/w
r/w
RFU
r/w
r/w
Table 64. Description of RxThresholdReg bits
Bit
Symbol
Description
7 to 4
MinLevel
Defines the minimum signal strength at the decoder input that shall be
accepted. If the signal strength is below this level, it is not evaluated.
3
-
Reserved for future use.
2 to 0
CollLevel
Defines the minimum signal strength at the decoder input that has to be
reached by the weaker half-bit of the Manchester-coded signal to
generate a bit-collision relatively to the amplitude of the stronger half-bit.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
44 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.10 DemodReg
Defines demodulator settings.
Table 65. DemodReg register (address 19h); reset value: 4Dh, 01001101b
7
6
5
4
3
2
1
0
AddIQ
FixIQ
TPrescal
Even
TauRcv
TauSync
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Table 66. Description of DemodReg bits
Bit
Symbol
Description
7 to 6
AddIQ
Defines the use of I and Q channel during reception
Note: FixIQ has to be set to logic 0 to
enable the following settings.
Value
00
Description
Select the stronger channel
01
Select the stronger and freeze the selected during communication
10
combines the I and Q channel
Reserved
11
5
4
FixIQ
If set to logic 1 and the bits of AddIQ are set to X0, the reception is fixed to
I channel.
If set to logic 1 and the bits of AddIQ are set to X1, the reception is fixed to
Q channel.
NOTE: If SIGIN/SIGOUT is used as S2C interface FixIQ set to 1 and AddIQ
set to X0 is rewired.
TPrescalE If set to logic 0 the following formula is used to calculate fTimer of the
ven
prescaler:
fTimer = 13.56 MHz / (2 * TPreScaler + 1).
If set to logic 1 the following formula is used to calculate fTimer of the
prescaler:
fTimer = 13.56 MHz / (2 * TPreScaler + 2).
(Default TPrescalEven is logic 0)
The behaviour for the version 1.0 is described in Section 21 “Errata
sheet” on page 109.
3 to 2
1 to 0
TauRcv
Changes the time constant of the internal during data reception.
Note: If set to 00, the PLL is frozen during data reception.
Changes the time constant of the internal PLL during burst.
TauSync
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
45 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.11 FelNFC1Reg
Defines the length of the FeliCa Sync bytes and the minimum length of the received
packet.
Table 67. FelNFC1Reg register (address 1Ah); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
FelSyncLen
r/w r/w
DataLenMin
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
Table 68. Description of FelNFC1Reg bits
Bit
Symbol
Description
7 to 6
FelSyncLen Defines the length of the Sync bytes.
Value
00
Sync- bytes in hex
B2 4D
01
00 B2 4D
10
00 00 B2 4D
00 00 00 B2 4D
11
5 to 0
DataLenMin These bits define the minimum length of the accepted packet length:
DataLenMin * 4 data packet length
This parameter is ignored at 106 kbit if the bit DetectSync in register
ModeReg is set to logic 0. If a received data packet is shorter than the
defined DataLenMin value, the data packet will be ignored.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
46 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.12 FelNFC2Reg
Defines the maximum length of the received packet.
Table 69. FelNFC2Reg register (address1Bh); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
WaitForSelected ShortTimeSlot
r/w r/w
DataLenMax
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
Table 70. Description of FelNFC2Reg bits
Bit
Symbol
Description
7
WaitForSelected Set to logic 1, the AutoColl command is only terminated
automatically when:
1. A valid command has been received after performing a valid
Select procedure according ISO/IEC 14443A.
2. A valid command has been received after performing a valid
Polling procedure according to the FeliCa specification.
Note: If this bit is set, no active communication is possible.
Note: Setting this bit reduces the host controller interaction in case
of a communication to another device in the same RF field during
Passive Communication mode.
6
ShortTimeSlot
DataLenMax
Defines the time slot length for Passive Communication mode at
424 kbit. Set to logic 1 a short time slot is used (half of the timeslot
at 212 kbit). Set to logic 0 a long timeslot is used (equal to the
timeslot for 212 kbit).
5 to 0
These bits define the maximum length of the accepted packet
length: DataLenMax * 4 data packet length
Note: If set to logic 0 the maximum data length is 256 bytes.
This parameter is ignored at 106 kbit if the bit DetectSync in
register ModeReg is set to logic 0. If a received packet is larger
than the defined DataLenMax value, the packet will be ignored.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
47 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.13 MifNFCReg
Defines ISO/IEC 14443A/MIFARE/NFC specific settings in target or Card Operating
mode.
Table 71. MifNFCReg register (address 1Ch); reset value: 62h, 01100010b
7
6
SensMiller
r/w
5
4
3
2
1
0
TauMiller
MFHalted
r/w
TxWait
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 72. Description of MifNFCReg bits
Bit
Symbol
Description
These bits define the sensitivity of the Miller decoder.
These bits define the time constant of the Miller decoder.
7 to 5
4 to 3
2
SensMiller
TauMiller
MFHalted
Set to logic 1, this bit indicates that the PN512 is set to HALT mode in
Card Operation mode at 106 kbit. This bit is either set by the host
controller or by the internal state machine and indicates that only the
code 52h is accepted as a request command. This bit is cleared
automatically by a RF reset.
1 to 0
TxWait
These bits define the minimum response time between receive and
transmit in number of data bits + 7 data bits.
The shortest possible minimum response time is 7 data bits.
(TxWait=0). The minimum response time can be increased by the
number of bits defined in TxWait. The longest minimum response time
is 10 data bits (TxWait = 3).
If a transmission of a frame is started before the minimum response
time is over, the PN512 waits before transmitting the data until the
minimum response time is over.
If a transmission of a frame is started after the minimum response time
is over, the frame is started immediately if the data bit synchronization
is correct. (adjustable with TxBitPhase).
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
48 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.14 ManualRCVReg
Allows manual fine tuning of the internal receiver.
Remark: For standard applications it is not recommended to change this register settings.
Table 73. ManualRCVReg register (address 1Dh); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
0
FastFilt
Delay
Parity
LargeBW Manual
HPFC
MF_SO MF_SO
Disable
PLL
HPCF
Access
Rights
RFU
r/w r/w
r/w
r/w
r/w
r/w
r/w
Table 74. Description of ManualRCVReg bits
Bit
7
Symbol
Description
-
Reserved for future use.
6
FastFilt
MF_SO
If this bit is set to logic 1, the internal filter for the Miller-Delay Circuit is
set to Fast mode.
Note: This bit should only set to logic 1, if Millerpulses of less than
400 ns Pulse length are expected. At 106 kBaud the typical value is
3 us.
5
Delay MF_SO If this bit is set to logic 1, the Signal at SIGOUT-pin is delayed, so that
in SAM mode the Signal at SIGIN must be 128/fc faster compared to
the ISO/IEC 14443A, to reach the ISO/IEC 14443A restrictions on the
RF-Field.
Note: This delay shall only be activated for setting bits SigOutSel to
(1110b) or (1111b) in register TxSelReg.
4
Parity Disable If this bit is set to logic 1, the generation of the Parity bit for
transmission and the Parity-Check for receiving is switched off. The
received Parity bit is handled like a data bit.
3
2
LargeBWPLL Set to logic 1, the bandwidth of the internal PLL used for clock
recovery is extended.
ManualHPCF Set to logic 0, the HPCF bits are ignored and the HPCF settings are
adapted automatically to the receiving mode. Set to logic 1, values of
HPCF are valid.
1 to 0
HPFC
Selects the High Pass Corner Frequency (HPCF) of the filter in the
internal receiver chain
00 For signals with frequency spectrum down to 106 kHz.
01 For signals with frequency spectrum down to 212 kHz.
10 For signals with frequency spectrum down to 424 kHz.
11 For signals with frequency spectrum down to 848 kHz
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
49 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.2.15 TypeBReg
Table 75. TypeBReg register (address 1Eh); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
RxSOF
Req
RxEOF
Req
0
EOFSO NoTxSOF NoTxEOF
FWidth
TxEGT
Access
Rights
r/w
r/w
RFU
r/w
r/w
r/w
r/w
r/w
Table 76. Description of TypeBReg bits
Bit
Symbol
Description
7
RxSOFReq
If this bit is set to logic 1, the SOF is required. A datastream starting
without SOF is ignored.
If this bit is cleared, a datastream with and without SOF is accepted.
The SOF will be removed and not written into the FIFO.
6
RxEOFReq
If this bit is set to logic 1, the EOF is required. A datastream ending
without EOF will generate a Protocol-Error. If this bit is cleared, a
datastream with and without EOF is accepted. The EOF will be
removed and not written into the FIFO.
For the behaviour in version 1.0, see Section 21 “Errata sheet” on
page 109.
5
4
-
Reserved for future use.
EOFSOFWidth If this bit is set to logic 1 and EOFSOFAdjust bit is logic 0, the SOF
and EOF will have the maximum length defined in ISO/IEC 14443B.
If this bit is cleared and EOFSOFAdjust bit is logic 0, the SOF and
EOF will have the minimum length defined in ISO/IEC 14443B.
If this bit is set to 1 and the EOFSOFadjust bit is logic 1 will result in
SOF low = (11etu 8 cycles)/fc
SOF high = (2 etu + 8 cycles)/fc
EOF low = (11 etu 8 cycles)/fc
If this bit is set to 0 and the EOFSOFAdjust bit is logic 1 will result in
an incorrect system behavior in respect to ISO specification.
For the behaviour in version 1.0, see Section 21 “Errata sheet” on
page 109.
3
NoTxSOF
NoTxEOF
TxEGT
If this bit is set to logic 1, the generation of the SOF is suppressed.
2
If this bit is set to logic 1, the generation of the EOF is suppressed.
1 to 0
These bits define the length of the EGT.
Value Description
00 0 bit
01 1 bit
10 2 bits
11 3 bits
9.2.2.16 SerialSpeedReg
Selects the speed of the serial UART interface.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
50 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 77. SerialSpeedReg register (address 1Fh); reset value: EBh, 11101011b
7
6
5
4
3
2
1
0
BR_T0
r/w
BR_T1
r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 78. Description of SerialSpeedReg bits
Bit
Symbol
Description
7 to 5
BR_T0
Factor BR_T0 to adjust the transfer speed, for description see Section
10.3.2 “Selectable UART transfer speeds”.
3 to 0
BR_T1
Factor BR_T1 to adjust the transfer speed, for description see Section
10.3.2 “Selectable UART transfer speeds”.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
51 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.3 Page 2: Configuration
9.2.3.1 PageReg
Selects the register page.
Table 79. PageReg register (address 20h); reset value: 00h, 00000000b
7
UsePageSelect
r/w
6
0
5
0
4
0
3
0
2
0
1
0
PageSelect
r/w r/w
Access Rights
RFU
RFU
RFU
RFU
RFU
Table 80. Description of PageReg bits
Bit
Symbol
Description
7
UsePageSelect Set to logic 1, the value of PageSelect is used as register address A5
and A4. The LSB-bits of the register address are defined by the
address pins or the internal address latch, respectively.
Set to logic 0, the whole content of the internal address latch defines
the register address. The address pins are used as described in
Section 10.1 “Automatic microcontroller interface detection”.
6 to 2
1 to 0
-
Reserved for future use.
PageSelect
The value of PageSelect is used only if UsePageSelect is set to
logic 1. In this case, it specifies the register page (which is A5 and
A4of the register address).
9.2.3.2 CRCResultReg
Shows the actual MSB and LSB values of the CRC calculation.
Note: The CRC is split into two 8-bit register.
Note: Setting the bit MSBFirst in ModeReg register reverses the bit order, the byte order is
not changed.
Table 81. CRCResultReg register (address 21h); reset value: FFh, 11111111b
7
6
5
4
3
2
1
0
CRCResultMSB
Access Rights
r
r
r
r
r
r
r
r
Table 82. Description of CRCResultReg bits
Bit
Symbol
Description
7 to 0
CRCResultMSB This register shows the actual value of the most significant byte of
the CRCResultReg register. It is valid only if bit CRCReady in
register Status1Reg is set to logic 1.
Table 83. CRCResultReg register (address 22h); reset value: FFh, 11111111b
7
6
5
4
3
2
1
0
CRCResultLSB
Access Rights
r
r
r
r
r
r
r
r
Table 84. Description of CRCResultReg bits
Bit
Symbol
Description
7 to 0
CRCResultLSB This register shows the actual value of the least significant byte of
the CRCResult register. It is valid only if bit CRCReady in register
Status1Reg is set to logic 1.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
52 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.3.3 GsNOffReg
Selects the conductance for the N-driver of the antenna driver pins TX1 and TX2 when the
driver is switched off.
Table 85. GsNOffReg register (address 23h); reset value: 88h, 10001000b
7
6
5
4
3
2
1
0
CWGsNOff
ModGsNOff
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 86. Description of GsNOffReg bits
Bit
Symbol
Description
7 to 4
CWGsNOff
The value of this register defines the conductance of the output
N-driver during times of no modulation.
Note: The conductance value is binary weighted.
Note: During soft Power-down mode the highest bit is forced to 1.
Note: The value of the register is only used if the driver is switched
off. Otherwise the bit value CWGsNOn of register GsNOnReg is
used.
Note: This value is used for LoadModulation.
3 to 0
ModGsNOff
The value of this register defines the conductance of the output
N-driver for the time of modulation. This may be used to regulate the
modulation index.
Note: The conductance value is binary weighted.
Note: During soft Power-down mode the highest bit is forced to 1.
Note: The value of the register is only used if the driver is switched
off. Otherwise the bit value ModGsNOn of register GsNOnReg is
used
Note: This value is used for LoadModulation.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
53 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.3.4 ModWidthReg
Controls the modulation width settings.
Table 87. ModWidthReg register (address 24h); reset value: 26h, 00100110b
7
6
5
4
3
2
1
0
ModWidth
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Table 88. Description of ModWidthReg bits
Bit
Symbol
Description
7 to 0
ModWidth
These bits define the width of the Miller modulation as initiator in Active
and Passive Communication mode as multiples of the carrier
frequency (ModWidth + 1/fc). The maximum value is half the bit
period.
Acting as a target in Passive Communication mode at 106 kbit or in
Card Operating mode for ISO/IEC 14443A/MIFARE these bits are
used to change the duty cycle of the subcarrier frequency.
The resulting number of carrier periods are calculated according to the
following formulas:
LOW value: #clocksLOW = (ModWidth modulo 8) + 1.
HIGH value: #clocksHIGH = 16-#clocksLOW.
9.2.3.5 TxBitPhaseReg
Adjust the bitphase at 106 kbit during transmission.
Table 89. TxBitPhaseReg register (address 25h); reset value: 87h, 10000111b
7
RcvClkChange
r/w
6
5
4
3
TxBitPhase
r/w
2
1
0
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 90. Description of TxBitPhaseReg bits
Bit
Symbol
Description
7
RcvClkChange Set to logic 1, the demodulator’s clock is derived by the external RF
field.
6 to 0
TxBitPhase
These bits are representing the number of carrier frequency clock
cycles, which are added to the waiting period before transmitting
data in all communication modes. TXBitPhase is used to adjust the
TX bit synchronization during passive NFCIP-1 communication mode
at 106 kbit and in ISO/IEC 14443A/MIFARE card mode.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
54 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.3.6 RFCfgReg
Configures the receiver gain and RF level detector sensitivity.
Table 91. RFCfgReg register (address 26h); reset value: 48h, 01001000b
7
RFLevelAmp
r/w
6
5
4
3
2
1
0
RxGain
RFLevel
r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 92. Description of RFCfgReg bits
Bit
7
Symbol
Description
RFLevelAmp Set to logic 1, this bit activates the RF level detectors’ amplifier.
6 to 4
RxGain
This register defines the receivers signal voltage gain factor:
Value
000
001
010
011
100
101
110
111
Description
18 dB
23 dB
18 dB
23 dB
33 dB
38 dB
43 dB
48 dB
3 to 0
RFLevel
Defines the sensitivity of the RF level detector, for description see
Section 12.3 “RF level detector”.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
55 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.3.7 GsNOnReg
Selects the conductance for the N-driver of the antenna driver pins TX1 and TX2 when the
driver is switched on.
Table 93. GsNOnReg register (address 27h); reset value: 88h, 10001000b
7
6
5
4
3
2
1
0
CWGsNOn
ModGsNOn
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 94. Description of GsNOnReg bits
Bit
Symbol
Description
7 to 4
CWGsNOn
The value of this register defines the conductance of the output
N-driver during times of no modulation. This may be used to regulate
the output power and subsequently current consumption and
operating distance.
Note: The conductance value is binary weighted.
Note: During soft Power-down mode the highest bit is forced to 1.
Note: This value is only used if the driver TX1 or TX2 are switched on.
Otherwise the value of the bits CWGsNOff of register GsNOffReg is
used.
3 to 0
ModGsNOn
The value of this register defines the conductance of the output
N-driver for the time of modulation. This may be used to regulate the
modulation index.
Note: The conductance value is binary weighted.
Note: During soft Power-down mode the highest bit is forced to 1.
Note: This value is only used if the driver TX1 or Tx2 are switched on.
Otherwise the value of the bits ModsNOff of register GsNOffReg is
used.
9.2.3.8 CWGsPReg
Defines the conductance of the P-driver during times of no modulation
Table 95. CWGsPReg register (address 28h); reset value: 20h, 00100000b
7
0
6
0
5
4
3
2
1
0
CWGsP
Access
Rights
RFU
RFU
r/w
r/w
r/w
r/w
r/w
r/w
Table 96. Description of CWGsPReg bits
Bit
Symbol
-
Description
Reserved for future use.
7 to 6
5 to 0
CWGsP
The value of this register defines the conductance of the output
P-driver. This may be used to regulate the output power and
subsequently current consumption and operating distance.
Note: The conductance value is binary weighted.
Note: During soft Power-down mode the highest bit is forced to 1.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
56 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.3.9 ModGsPReg
Defines the driver P-output conductance during modulation.
Table 97. ModGsPReg register (address 29h); reset value: 20h, 00100000b
7
0
6
0
5
4
3
2
1
0
ModGsP
Access
Rights
RFU
RFU
r/w
r/w
r/w
r/w
r/w
r/w
Table 98. Description of ModGsPReg bits
Bit
Symbol
Description
Reserved for future use.
The value of this register defines the conductance of the output
7 to 6
5 to 0
-
ModGsP[1]
P-driver for the time of modulation. This may be used to regulate the
modulation index.
Note: The conductance value is binary weighted.
Note: During soft Power-down mode the highest bit is forced to 1.
[1] If Force100ASK is set to logic 1, the value of ModGsP has no effect.
9.2.3.10 TMode Register, TPrescaler Register
Defines settings for the timer.
Note: The Prescaler value is split into two 8-bit registers
Table 99. TModeReg register (address 2Ah); reset value: 00h, 00000000b
7
6
5
4
TAutoRestart
r/w
3
2
1
0
TAuto
r/w
TGated
TPrescaler_Hi
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
Table 100. Description of TModeReg bits
Bit
Symbol
Description
7
TAuto
Set to logic 1, the timer starts automatically at the end of the transmission
in all communication modes at all speeds or when bit InitialRFOn is set to
logic 1 and the RF field is switched on.
In mode MIFARE and ISO14443-B 106kbit/s the timer stops after the 5th
bit (1 startbit, 4 databits) if the bit RxMultiple in the register RxModeReg is
not set. In all other modes, the timer stops after the 4th bit if the bit
RxMultiple the register RxModeReg is not set.
If RxMultiple is set to logic 1, the timer never stops. In this case the timer
can be stopped by setting the bit TStopNow in register ControlReg to 1.
Set to logic 0 indicates, that the timer is not influenced by the protocol.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
57 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 100. Description of TModeReg bits …continued
Bit Symbol Description
6 to 5 TGated
The internal timer is running in gated mode.
Note: In the gated mode, the bit TRunning is 1 when the timer is enabled
by the register bits. This bit does not influence the gating signal.
Value
00
Description
Non gated mode
Gated by SIGIN
Gated by AUX1
Gated by A3
01
10
11
4
TAutoRestart Set to logic 1, the timer automatically restart its count-down from
TReloadValue, instead of counting down to zero.
Set to logic 0 the timer decrements to ZERO and the bit TimerIRq is set
to logic 1.
3 to 0 TPrescaler_Hi Defines higher 4 bits for TPrescaler.
The following formula is used to calculate fTimer if TPrescalEven bit in
Demot Reg is set to logic 0:
Timer = 13.56 MHz/(2*TPreScaler+1).
f
Where TPreScaler = [TPrescaler_Hi:TPrescaler_Lo] (TPrescaler value
on 12 bits) (Default TPrescalEven is logic 0)
The following formula is used to calculate fTimer if TPrescalEven bit in
Demot Reg is set to logic 1:
f
Timer = 13.56 MHz/(2*TPreScaler+2).
For detailed description see Section 15 “Timer unit”. For the behaviour
within version 1.0, see Section 21 “Errata sheet” on page 109.
Table 101. TPrescalerReg register (address 2Bh); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
TPrescaler_Lo
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 102. Description of TPrescalerReg bits
Bit
Symbol
Description
7 to 0
TPrescaler_Lo Defines lower 8 bits for TPrescaler.
The following formula is used to calculate fTimer if TPrescalEven bit in
Demot Reg is set to logic 0:
f
Timer = 13.56 MHz/(2*TPreScaler+1).
Where TPreScaler = [TPrescaler_Hi:TPrescaler_Lo] (TPrescaler value
on 12 bits)
The following formula is used to calculate fTimer if TPrescalEven bit in
Demot Reg is set to logic 1:
f
Timer = 13.56 MHz/(2*TPreScaler+2).
Where TPreScaler = [TPrescaler_Hi:TPrescaler_Lo] (TPrescaler value
on 12 bits)
For detailed description see Section 15 “Timer unit”.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
58 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.3.11 TReloadReg
Describes the 16-bit long timer reload value.
Note: The Reload value is split into two 8-bit registers.
Table 103. TReloadReg (Higher bits) register (address 2Ch); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
TReloadVal_Hi
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 104. Description of the higher TReloadReg bits
Bit
Symbol
Description
7 to 0
TReloadVal_Hi Defines the higher 8 bits for the TReloadReg.
With a start event the timer loads the TReloadVal. Changing this
register affects the timer only at the next start event.
Table 105. TReloadReg (Lower bits) register (address 2Dh); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
TReloadVal_Lo
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 106. Description of lower TReloadReg bits
Bit
Symbol
Description
7 to 0
TReloadVal_Lo Defines the lower 8 bits for the TReloadReg.
With a start event the timer loads the TReloadVal. Changing this
register affects the timer only at the next start event.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
59 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.3.12 TCounterValReg
Contains the current value of the timer.
Note: The Counter value is split into two 8-bit register.
Table 107. TCounterValReg (Higher bits) register (address 2Eh); reset value: XXh,
XXXXXXXXb
7
6
5
4
3
2
1
0
TCounterVal_Hi
Access
Rights
r
r
r
r
r
r
r
r
Table 108. Description of the higher TCounterValReg bits
Bit
Symbol
Description
7 to 0
TCounterVal_Hi Current value of the timer, higher 8 bits.
Table 109. TCounterValReg (Lower bits) register (address 2Fh); reset value: XXh,
XXXXXXXXb
7
6
5
4
3
2
1
0
TCounterVal_Lo
Access
Rights
r
r
r
r
r
r
r
r
Table 110. Description of lower TCounterValReg bits
Bit
Symbol
Description
7 to 0
TCounterVal_Lo Current value of the timer, lower 8 bits.
9.2.4 Page 3: Test
9.2.4.1 PageReg
Selects the register page.
Table 111. PageReg register (address 30h); reset value: 00h, 00000000b
7
UsePageSelect
r/w
6
0
5
0
4
0
3
0
2
0
1
0
PageSelect
r/w r/w
Access
Rights
RFU
RFU
RFU
RFU
RFU
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
60 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 112. Description of PageReg bits
Bit
Symbol
Description
7
UsePageSelect Set to logic 1, the value of PageSelect is used as register address
A5 and A4. The LSB-bits of the register address are defined by the
address pins or the internal address latch, respectively.
Set to logic 0, the whole content of the internal address latch defines
the register address. The address pins are used as described in
Section 10.1 “Automatic microcontroller interface detection”.
6 to 2
1 to 0
-
Reserved for future use.
PageSelect
The value of PageSelect is used only if UsePageSelect is set to
logic 1. In this case, it specifies the register page (which is A5 and
A4 of the register address).
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
61 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.4.2 TestSel1Reg
General test signal configuration.
Table 113. TestSel1Reg register (address 31h); reset value: 00h, 00000000b
7
-
6
-
5
4
3
SAMClkD1
r/w
2
1
TstBusBitSel
r/w
0
SAMClockSel
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
Table 114. Description of TestSel1Reg bits
Bit
Symbol
Description
Reserved for future use.
7 to 6
5 to 4
-
SAMClockSel Defines the source for the 13.56 MHz SAM clock
Value
00
Description
GND- Sam Clock switched off
clock derived by the internal oscillator
internal UART clock
01
10
11
clock derived by the RF field
3
SAMClkD1
Set to logic 1, the SAM clock is delivered to D1.
Note: Only possible if the 8bit parallel interface is not used.
Select the TestBus bit from the testbus to be propagated to SIGOUT.
2 to 0
TstBusBitSel
9.2.4.3 TestSel2Reg
General test signal configuration and PRBS control
Table 115. TestSel2Reg register (address 32h); reset value: 00h, 00000000b
7
TstBusFlip
r/w
6
5
4
3
2
TestBusSel
r/w
1
0
PRBS9 PRBS15
r/w r/w
Access
Rights
r/w
r/w
r/w
r/w
Table 116. Description of TestSel2Reg bits
Bit
Symbol
Description
7
TstBusFlip
If set to logic 1, the testbus is mapped to the parallel port by the
following order:
D4, D3, D2, D6, D5, D0, D1. See Section 20 “Testsignals”.
Starts and enables the PRBS9 sequence according ITU-TO150.
6
PRBS9
Note: All relevant registers to transmit data have to be configured
before entering PRBS9 mode.
Note: The data transmission of the defined sequence is started by the
send command.
5
PRBS15
Starts and enables the PRBS15 sequence according ITU-TO150.
Note: All relevant registers to transmit data have to be configured
before entering PRBS15 mode.
Note: The data transmission of the defined sequence is started by the
send command.
4 to 0
TestBusSel
Selects the testbus. See Section 20 “Testsignals”
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
62 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.4.4 TestPinEnReg
Enables the pin output driver on the 8-bit parallel bus.
Table 117. TestPinEnReg register (address 33h); reset value: 80h, 10000000b
7
RS232LineEn
r/w
6
5
4
3
2
1
0
TestPinEn
r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 118. Description of TestPinEnReg bits
Bit
Symbol
Description
7
RS232LineEn Set to logic 0, the lines MX and DTRQ for the serial UART are
disabled.
6 to 0
TestPinEn
Enables the pin output driver on the 8-bit parallel interface.
Example:
Setting bit 0 to 1 enables D0
Setting bit 5 to 1 enables D5
Note: Only valid if one of serial interfaces is used.
If the SPI interface is used only D0 to D4 can be used. If the serial
UART interface is used and RS232LineEn is set to logic 1 only D0 to
D4 can be used.
9.2.4.5 TestPinValueReg
Defines the values for the 7-bit parallel port when it is used as I/O.
Table 119. TestPinValueReg register (address 34h); reset value: 00h, 00000000b
7
6
5
4
3
TestPinValue
r/w
2
1
0
UseIO
r/w
Access
Rights
r/w
r/w
r/w
r/w
r/w
r/w
Table 120. Description of TestPinValueReg bits
Bit
Symbol
Description
7
UseIO
Set to logic 1, this bit enables the I/O functionality for the 7-bit parallel
port in case one of the serial interfaces is used. The input/output
behavior is defined by TestPinEn in register TestPinEnReg. The value
for the output behavior is defined in the bits TestPinVal.
Note: If SAMClkD1 is set to logic 1, D1 can not be used as I/O.
6 to 0
TestPinValue Defines the value of the 7-bit parallel port, when it is used as I/O. Each
output has to be enabled by the TestPinEn bits in register
TestPinEnReg.
Note: Reading the register indicates the actual status of the pins D6 -
D0 if UseIO is set to logic 1. If UseIO is set to logic 0, the value of the
register TestPinValueReg is read back.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
63 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.4.6 TestBusReg
Shows the status of the internal testbus.
Table 121. TestBusReg register (address 35h); reset value: XXh, XXXXXXXXb
7
6
5
4
3
2
1
0
TestBus
Access Rights
r
r
r
r
r
r
r
r
Table 122. Description of TestBusReg bits
Bit
Symbol
Description
7 to 0
TestBus
Shows the status of the internal testbus. The testbus is selected by the
register TestSel2Reg. See Section 20 “Testsignals”.
9.2.4.7 AutoTestReg
Controls the digital selftest.
Table 123. AutoTestReg register (address 36h); reset value: 40h, 01000000b
7
6
5
4
3
2
1
0
0
AmpRcv EOFSO
FAdjust
-
SelfTest
Access Rights
RFT
r/w
RFU
RFU
r/w
r/w
r/w
r/w
Table 124. Description of bits
Bit
7
Symbol
-
Description
Reserved for production tests.
6
AmpRcv
If set to logic 1, the internal signal processing in the receiver chain is
performed non-linear. This increases the operating distance in
communication modes at 106 kbit.
Note: Due to the non linearity the effect of the bits MinLevel and
CollLevel in the register RxThreshholdReg are as well non linear.
5
EOFSOFAdjust If set to logic 0 and the EOFSOFwidth is set to 1 will result in the
Maximum length of SOF and EOF according to ISO/IEC14443B
If set to logic 0 and the EOFSOFwidth is set to 0 will result in the
Minimum length of SOF and EOF according to ISO/IEC14443B
If this bit is set to 1 and the EOFSOFwidth bit is logic 1 will result in
SOF low = (11 etu 8 cycles)/fc
SOF high = (2 etu + 8 cycles)/fc
EOF low = (11 etu 8 cycles)/fc
For the behaviour in version 1.0, see Section 21 “Errata sheet” on
page 109.
4
-
Reserved for future use.
3 to 0
SelfTest
Enables the digital self test. The selftest can be started by the selftest
command in the command register. The selftest is enabled by 1001.
Note: For default operation the selftest has to be disabled by 0000.
9.2.4.8 VersionReg
Shows the version.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
64 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 125. VersionReg register (address 37h); reset value: XXh, XXXXXXXXb
7
6
5
4
3
2
1
0
Version
Access Rights
r
r
r
r
r
r
r
r
Table 126. Description of VersionReg bits
Bit
Symbol
Description
7 to 0
Version
80h indicates PN512 version 1.0, differences to version 2.0 are
described within Section 21 “Errata sheet” on page 109.
82h indicates PN512 version 2.0, which covers also the industrial
version.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
65 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.4.9 AnalogTestReg
Controls the pins AUX1 and AUX2
Table 127. AnalogTestReg register (address 38h); reset value: 00h, 00000000b
7
6
5
4
3
2
1
0
AnalogSelAux1
r/w r/w
AnalogSelAux2
r/w r/w
Access Rights
r/w
r/w
r/w
r/w
Table 128. Description of AnalogTestReg bits
Bit Symbol Description
7 to 4 AnalogSelAux1 Controls the AUX pin.
3 to 0 AnalogSelAux2 Note: All test signals are described in Section 20 “Testsignals”.
Value Description
0000
0001
Tristate
Output of TestDAC1 (AUX1), output of TESTDAC2 (AUX2)
Note: Current output. The use of 1 k pull-down resistor on AUX is recommended.
0010
0011
0100
0101
0110
0111
1000
Testsignal Corr1
Note: Current output. The use of 1 k pull-down resistor on AUX is recommended.
Testsignal Corr2
Note: Current output. The use of 1 k pull-down resistor on AUX is recommended.
Testsignal MinLevel
Note: Current output. The use of 1 k pull-down resistor on AUX is recommended.
Testsignal ADC channel I
Note: Current output. The use of 1 k pull-down resistor on AUX is recommended.
Testsignal ADC channel Q
Note: Current output. The use of 1 k pull-down resistor on AUX is recommended.
Testsignal ADC channel I combined with Q
Note: Current output. The use of 1 k pull-down resistor on AUX is recommended.
Testsignal for production test
Note: Current output. The use of 1 k pull-down resistor on AUX is recommended.
1001
1010
1011
1100
SAM clock (13.56 MHz)
HIGH
LOW
TxActive
At 106 kbit: HIGH during Startbit, Data bit, Parity and CRC. At 212 and 424 kbit: High
during Preamble, Sync, Data and CRC.
1101
1110
1111
RxActive
At 106 kbit: High during databit, Parity and CRC.
At 212 and 424 kbit: High during data and CRC.
Subcarrier detected
106 kbit: not applicable
212 and 424 kbit: High during last part of Preamble, Sync data and CRC
TestBus-Bit as defined by the TstBusBitSel in register TestSel1Reg.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
66 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.4.10 TestDAC1Reg
Defines the testvalues for TestDAC1.
Table 129. TestDAC1Reg register (address 39h); reset value: XXh, 00XXXXXXb
7
0
6
0
5
4
3
2
1
0
TestDAC1
Access
Rights
RFT
RFU
r/w
r/w
r/w
r/w
r/w
r/w
Table 130. Description of TestDAC1Reg bits
Bit
7
Symbol
Description
-
Reserved for production tests.
Reserved for future use.
6
-
5 to 0
TestDAC1
Defines the testvalue for TestDAC1. The output of the DAC1 can be
switched to AUX1 by setting AnalogSelAux1 to 0001 in register
AnalogTestReg.
9.2.4.11 TestDAC2Reg
Defines the testvalue for TestDAC2.
Table 131. TestDAC2Reg register (address 3Ah); reset value: XXh, 00XXXXXXb
7
0
6
0
5
4
3
2
1
0
TestDAC2
Access
Rights
RFU
RFU
r/w
r/w
r/w
r/w
r/w
r/w
Table 132. Description ofTestDAC2Reg bits
Bit
Symbol
-
Description
Reserved for future use.
7 to 6
5 to 0
TestDAC2
Defines the testvalue for TestDAC2. The output of the DAC2 can be
switched to AUX2 by setting AnalogSelAux2 to 0001 in register
AnalogTestReg.
9.2.4.12 TestADCReg
Shows the actual value of ADC I and Q channel.
Table 133. TestADCReg register (address 3Bh); reset value: XXh, XXXXXXXXb
7
6
5
4
3
2
1
0
ADC_I
ADC_Q
Access
Rights
Table 134. Description of TestADCReg bits
Bit
Symbol
ADC_I
Description
7 to 4
3 to 0
Shows the actual value of ADC I channel.
Shows the actual value of ADC Q channel.
ADC_Q
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
67 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
9.2.4.13 RFTReg
Table 135. RFTReg register (address 3Ch); reset value: FFh, 11111111b
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
1
Access
Rights
RFT
RFT
RFT
RFT
RFT
RFT
RFT
RFT
Table 136. Description of RFTReg bits
Bit
Symbol
Description
Reserved for production tests.
7 to 0
-
Table 137. RFTReg register (address 3Dh, 3Fh); reset value: 00h, 00000000b
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Access
Rights
RFT
RFT
RFT
RFT
RFT
RFT
RFT
RFT
Table 138. Description of RFTReg bits
Bit
Symbol
Description
Reserved for production tests.
7 to 0
-
Table 139. RFTReg register (address 3Eh); reset value: 03h, 00000011b
7
0
6
0
5
0
4
0
3
0
2
0
1
1
0
1
Access
Rights
RFT
RFT
RFT
RFT
RFT
RFT
RFT
RFT
Table 140. Description of RFTReg bits
Bit
Symbol
Description
Reserved for production tests.
7 to 0
-
10. Digital interfaces
10.1 Automatic microcontroller interface detection
The PN512 supports direct interfacing of hosts using SPI, I2C-bus or serial UART
interfaces. The PN512 resets its interface and checks the current host interface type
automatically after performing a power-on or hard reset. The PN512 identifies the host
interface by sensing the logic levels on the control pins after the reset phase. This is done
using a combination of fixed pin connections. Table 141 shows the different connection
configurations.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
68 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 141. Connection protocol for detecting different interface types
Pin
Interface type
UART (input)
SPI (output)
I2C-bus (I/O)
SDA
SDA
I2C
EA
D7
D6
D5
D4
D3
D2
D1
RX
NSS
0
0
1
0
1
EA
TX
MISO
SCL
MX
MOSI
ADR_0
ADR_1
ADR_2
ADR_3
ADR_4
ADR_5
DTRQ
SCK
-
-
-
-
-
-
-
-
Table 142. Connection scheme for detecting the different interface types
PN512 Parallel Interface Type Serial Interface Types
Separated Read/Write Strobe Common Read/Write Strobe
Dedicated Multiplexed Dedicated Multiplexed
Address Bus Address Bus Address Bus Address Bus
I2C
Pin
UART
SPI
ALE
1
ALE
0
1
AS
RX
NSS
SDA
0
A5[1]
A4[1]
A3[1]
A2[1]
A1
A5
A4
A3
A2
A1
A0
A5
0
0
0
0
A4
0
0
0
0
0
A3
0
0
0
0
1
A2
1
0
0
0
1
A1
1
0
0
1
A0
1
A0
0
0
1
EA
NRD[1] NRD
NWR[1] NWR
NCS[1] NCS
NRD
NWR
NCS
D7
NDS
RD/NWR
NCS
D7
NDS
RD/NWR
NCS
D7
1
1
1
1
1
1
NCS
NCS
NCS
SCL
ADR_0
ADR_1
ADR_2
ADR_3
ADR_4
ADR_5
ADR_6
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
TX
MISO
D6
D6
D6
MX
MOSI
AD5
AD4
AD3
AD2
AD1
AD0
D5
AD5
AD4
AD3
AD2
AD1
AD0
DTRQ
SCK
D4
-
-
-
-
-
-
-
-
-
-
D3
D2
D1
D0
Remark: Overview on the pin behavior
Pin behavior Input Output
In/Out
[1] only available in HVQFN 40.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
69 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
10.2 Serial Peripheral Interface
A serial peripheral interface (SPI compatible) is supported to enable high-speed
communication to the host. The interface can handle data speeds up to 10 Mbit/s. When
communicating with a host, the PN512 acts as a slave, receiving data from the external
host for register settings, sending and receiving data relevant for RF interface
communication.
An interface compatible with SPI enables high-speed serial communication between the
PN512 and a microcontroller. The implemented interface is in accordance with the SPI
standard.
The timing specification is given in Section 26.1 on page 117.
PN512
SCK
SCK
MOSI
MOSI
MISO
MISO
NSS
NSS
001aan220
Fig 13. SPI connection to host
The PN512 acts as a slave during SPI communication. The SPI clock signal SCK must be
generated by the master. Data communication from the master to the slave uses the
MOSI line. The MISO line is used to send data from the PN512 to the master.
Data bytes on both MOSI and MISO lines are sent with the MSB first. Data on both MOSI
and MISO lines must be stable on the rising edge of the clock and can be changed on the
falling edge. Data is provided by the PN512 on the falling clock edge and is stable during
the rising clock edge.
10.2.1 SPI read data
Reading data using SPI requires the byte order shown in Table 143 to be used. It is
possible to read out up to n-data bytes.
The first byte sent defines both the mode and the address.
Table 143. MOSI and MISO byte order
Line
Byte 0
address 0
X[1]
Byte 1
Byte 2
To
...
Byte n
Byte n + 1
00
MOSI
MISO
address 1
data 0
address 2
data 1
address n
data n 1
...
data n
[1] X = Do not care.
Remark: The MSB must be sent first.
10.2.2 SPI write data
To write data to the PN512 using SPI requires the byte order shown in Table 144. It is
possible to write up to n data bytes by only sending one address byte.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
70 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
The first send byte defines both the mode and the address byte.
Table 144. MOSI and MISO byte order
Line
Byte 0
address 0
X[1]
Byte 1
data 0
X[1]
Byte 2
data 1
X[1]
To
...
Byte n
data n 1
X[1]
Byte n + 1
data n
X[1]
MOSI
MISO
...
[1] X = Do not care.
Remark: The MSB must be sent first.
10.2.3 SPI address byte
The address byte has to meet the following format.
The MSB of the first byte defines the mode used. To read data from the PN512 the MSB is
set to logic 1. To write data to the PN512 the MSB must be set to logic 0. Bits 6 to 1 define
the address and the LSB is set to logic 0.
Table 145. Address byte 0 register; address MOSI
7 (MSB)
6
5
4
3
2
1
0 (LSB)
1 = read
0 = write
address
0
10.3 UART interface
10.3.1 Connection to a host
PN512
RX
TX
RX
TX
DTRQ
MX
DTRQ
MX
001aan221
Fig 14. UART connection to microcontrollers
Remark: Signals DTRQ and MX can be disabled by clearing TestPinEnReg register’s
RS232LineEn bit.
10.3.2 Selectable UART transfer speeds
The internal UART interface is compatible with an RS232 serial interface.
The default transfer speed is 9.6 kBd. To change the transfer speed, the host controller
must write a value for the new transfer speed to the SerialSpeedReg register. Bits
BR_T0[2:0] and BR_T1[4:0] define the factors for setting the transfer speed in the
SerialSpeedReg register.
The BR_T0[2:0] and BR_T1[4:0] settings are described in Table 10. Examples of different
transfer speeds and the relevant register settings are given in Table 11.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
71 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 146. BR_T0 and BR_T1 settings
BR_Tn
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
BR_T0 factor
BR_T1 range
1
1
2
4
8
16
32
64
1 to 32 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64
Table 147. Selectable UART transfer speeds
Transfer speed (kBd)
SerialSpeedReg value
Transfer speed accuracy (%)[1]
Decimal
250
235
218
203
171
154
122
116
90
Hexadecimal
FAh
7.2
0.25
0.32
9.6
EBh
14.4
19.2
38.4
57.6
115.2
128
DAh
0.25
0.32
CBh
ABh
0.32
9Ah
0.25
0.25
0.06
0.25
0.25
1.45
7Ah
74h
230.4
460.8
921.6
1228.8
5Ah
58
3Ah
28
1Ch
21
15h
0.32
[1] The resulting transfer speed error is less than 1.5 % for all described transfer speeds.
The selectable transfer speeds shown in Table 11 are calculated according to the
following equations:
If BR_T0[2:0] = 0:
27.12 106
BR_T0 + 1
-------------------------------
transfer speed =
(1)
(2)
If BR_T0[2:0] > 0:
27.12 106
-----------------------------------
transfer speed =
BR_T1 + 33
----------------------------------
2BR_T0 – 1
Remark: Transfer speeds above 1228.8 kBd are not supported.
10.3.3 UART framing
Table 148. UART framing
Bit
Length
1-bit
Value
0
Start
Data
Stop
8 bits
1-bit
data
1
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
72 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Remark: The LSB for data and address bytes must be sent first. No parity bit is used
during transmission.
Read data: To read data using the UART interface, the flow shown in Table 149 must be
used. The first byte sent defines both the mode and the address.
Table 149. Read data byte order
Pin
Byte 0
address
-
Byte 1
-
RX (pin 24)
TX (pin 31)
data 0
ADDRESS
RX
SA
A0
A1
A2
A3
A4
A5
(1)
R/W SO
DATA
TX
SA
D0
D1
D2
D3
D4
D5
D6
D7
SO
MX
DTRQ
001aak588
(1) Reserved.
Fig 15. UART read data timing diagram
Write data: To write data to the PN512 using the UART interface, the structure shown in
Table 150 must be used.
The first byte sent defines both the mode and the address.
Table 150. Write data byte order
Pin
Byte 0
Byte 1
RX (pin 24)
TX (pin 31)
address 0
-
data 0
address 0
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
73 of 136
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
ADDRESS
DATA
RX
SA A0 A1 A2 A3 A4 A5
(1) R/W SO
SA D0 D1 D2 D3 D4 D5 D6 D7 SO
ADDRESS
TX
SA A0 A1 A2 A3 A4 A5
(1) R/W SO
MX
DTRQ
001aak589
(1) Reserved.
Fig 16. UART write data timing diagram
Remark: The data byte can be sent directly after the address byte on pin RX.
Address byte: The address byte has to meet the following format:
PN512
NXP Semiconductors
Full NFC Forum compliant solution
The MSB of the first byte sets the mode used. To read data from the PN512, the MSB is
set to logic 1. To write data to the PN512 the MSB is set to logic 0. Bit 6 is reserved for
future use, and bits 5 to 0 define the address; see Table 151.
Table 151. Address byte 0 register; address MOSI
7 (MSB)
6
5
4
3
2
1
0 (LSB)
1 = read
0 = write
reserved
address
10.4 I2C Bus Interface
An I2C-bus (Inter-IC) interface is supported to enable a low-cost, low pin count serial bus
interface to the host. The I2C-bus interface is implemented according to
NXP Semiconductors’ I2C-bus interface specification, rev. 2.1, January 2000. The
interface can only act in Slave mode. Therefore the PN512 does not implement clock
generation or access arbitration.
PULL-UP
NETWORK
PULL-UP
NETWORK
PN512
SDA
SCL
MICROCONTROLLER
I2C
EA
CONFIGURATION
WIRING
ADR_[5:0]
001aan222
Fig 17. I2C-bus interface
The PN512 can act either as a slave receiver or slave transmitter in Standard mode, Fast
mode and High-speed mode.
SDA is a bidirectional line connected to a positive supply voltage using a current source or
a pull-up resistor. Both SDA and SCL lines are set HIGH when data is not transmitted. The
PN512 has a 3-state output stage to perform the wired-AND function. Data on the I2C-bus
can be transferred at data rates of up to 100 kBd in Standard mode, up to 400 kBd in Fast
mode or up to 3.4 Mbit/s in High-speed mode.
If the I2C-bus interface is selected, spike suppression is activated on lines SCL and SDA
as defined in the I2C-bus interface specification.
See Table 171 on page 117 for timing requirements.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
75 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
10.4.1 Data validity
Data on the SDA line must be stable during the HIGH clock period. The HIGH or LOW
state of the data line must only change when the clock signal on SCL is LOW.
SDA
SCL
data line
stable;
data valid
change
of data
allowed
mbc621
Fig 18. Bit transfer on the I2C-bus
10.4.2 START and STOP conditions
To manage the data transfer on the I2C-bus, unique START (S) and STOP (P) conditions
are defined.
• A START condition is defined with a HIGH-to-LOW transition on the SDA line while
SCL is HIGH.
• A STOP condition is defined with a LOW-to-HIGH transition on the SDA line while
SCL is HIGH.
The I2C-bus master always generates the START and STOP conditions. The bus is busy
after the START condition. The bus is free again a certain time after the STOP condition.
The bus stays busy if a repeated START (Sr) is generated instead of a STOP condition.
The START (S) and repeated START (Sr) conditions are functionally identical. Therefore,
S is used as a generic term to represent both the START (S) and repeated START (Sr)
conditions.
SDA
SCL
SDA
SCL
S
P
START condition
STOP condition
mbc622
Fig 19. START and STOP conditions
10.4.3 Byte format
Each byte must be followed by an acknowledge bit. Data is transferred with the MSB first;
see Figure 22. The number of transmitted bytes during one data transfer is unrestricted
but must meet the read/write cycle format.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
76 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
10.4.4 Acknowledge
An acknowledge must be sent at the end of one data byte. The acknowledge-related clock
pulse is generated by the master. The transmitter of data, either master or slave, releases
the SDA line (HIGH) during the acknowledge clock pulse. The receiver pulls down the
SDA line during the acknowledge clock pulse so that it remains stable LOW during the
HIGH period of this clock pulse.
The master can then generate either a STOP (P) condition to stop the transfer or a
repeated START (Sr) condition to start a new transfer.
A master-receiver indicates the end of data to the slave-transmitter by not generating an
acknowledge on the last byte that was clocked out by the slave. The slave-transmitter
releases the data line to allow the master to generate a STOP (P) or repeated START (Sr)
condition.
data output
by transmitter
not acknowledge
data output
by receiver
acknowledge
SCL from
master
1
2
8
9
S
clock pulse for
acknowledgement
START
condition
mbc602
Fig 20. Acknowledge on the I2C-bus
P
SDA
Sr
acknowledgement
signal from slave
acknowledgement
signal from receiver
MSB
byte complete,
interrupt within slave
clock line held LOW while
interrupts are serviced
S
or
Sr
Sr
or
P
SCL
1
2
7
8
9
1
2
3 - 8
9
ACK
ACK
START or
repeated START
condition
STOP or
repeated START
condition
msc608
Fig 21. Data transfer on the I2C-bus
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
77 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
10.4.5 7-Bit addressing
During the I2C-bus address procedure, the first byte after the START condition is used to
determine which slave will be selected by the master.
Several address numbers are reserved. During device configuration, the designer must
ensure that collisions with these reserved addresses cannot occur. Check the I2C-bus
specification for a complete list of reserved addresses.
The I2C-bus address specification is dependent on the definition of pin EA. Immediately
after releasing pin NRSTPD or after a power-on reset, the device defines the I2C-bus
address according to pin EA.
If pin EA is set LOW, the upper 4 bits of the device bus address are reserved by
NXP Semiconductors and set to 0101b for all PN512 devices. The remaining 3 bits
(ADR_0, ADR_1, ADR_2) of the slave address can be freely configured by the customer
to prevent collisions with other I2C-bus devices.
If pin EA is set HIGH, ADR_0 to ADR_5 can be completely specified at the external pins
according to Table 141 on page 69. ADR_6 is always set to logic 0.
In both modes, the external address coding is latched immediately after releasing the
reset condition. Further changes at the used pins are not taken into consideration.
Depending on the external wiring, the I2C-bus address pins can be used for test signal
outputs.
MSB
bit 6
LSB
R/W
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
slave address
001aak591
Fig 22. First byte following the START procedure
10.4.6 Register write access
To write data from the host controller using the I2C-bus to a specific register in the PN512
the following frame format must be used.
• The first byte of a frame indicates the device address according to the I2C-bus rules.
• The second byte indicates the register address followed by up to n-data bytes.
In one frame all data bytes are written to the same register address. This enables fast
FIFO buffer access. The Read/Write (R/W) bit is set to logic 0.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
78 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
10.4.7 Register read access
To read out data from a specific register address in the PN512, the host controller must
use the following procedure:
• Firstly, a write access to the specific register address must be performed as indicated
in the frame that follows
• The first byte of a frame indicates the device address according to the I2C-bus rules
• The second byte indicates the register address. No data bytes are added
• The Read/Write bit is 0
After the write access, read access can start. The host sends the device address of the
PN512. In response, the PN512 sends the content of the read access register. In one
frame all data bytes can be read from the same register address. This enables fast FIFO
buffer access or register polling.
The Read/Write (R/W) bit is set to logic 1.
write cycle
2
I C-BUS
SLAVE ADDRESS
[A7:A0]
0
(W)
JOINER REGISTER
ADDRESS [A5:A0]
DATA
[7:0]
S
A
0
0
A
[0:n]
A
P
read cycle
0
2
I C-BUS
0
(W)
JOINER REGISTER
ADDRESS [A5:A0]
SLAVE ADDRESS
[A7:A0]
S
A
0
A
P
optional, if the previous access was on the same register address
[0:n]
2
I C-BUS
1
(R)
DATA
[7:0]
SLAVE ADDRESS
[A7:A0]
S
A
[0:n]
A
A
DATA
[7:0]
P
sent by master
S
P
A
start condition
stop condition
acknowledge
A
not acknowledge
write cycle
W
R
sent by slave
read cycle
001aak592
Fig 23. Register read and write access
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
79 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
10.4.8 High-speed mode
In High-speed mode (HS mode), the device can transfer information at data rates of up to
3.4 Mbit/s, while remaining fully downward-compatible with Fast or Standard mode
(F/S mode) for bidirectional communication in a mixed-speed bus system.
10.4.9 High-speed transfer
To achieve data rates of up to 3.4 Mbit/s the following improvements have been made to
I2C-bus operation.
• The inputs of the device in HS mode incorporate spike suppression, a Schmitt trigger
on the SDA and SCL inputs and different timing constants when compared to
F/S mode
• The output buffers of the device in HS mode incorporate slope control of the falling
edges of the SDA and SCL signals with different fall times compared to F/S mode
10.4.10 Serial data transfer format in HS mode
The HS mode serial data transfer format meets the Standard mode I2C-bus specification.
HS mode can only start after all of the following conditions (all of which are in F/S mode):
1. START condition (S)
2. 8-bit master code (00001XXXb)
3. Not-acknowledge bit (A)
When HS mode starts, the active master sends a repeated START condition (Sr) followed
by a 7-bit slave address with a R/W bit address and receives an acknowledge bit (A) from
the selected PN512.
Data transfer continues in HS mode after the next repeated START (Sr), only switching
back to F/S mode after a STOP condition (P). To reduce the overhead of the master code,
a master links a number of HS mode transfers, separated by repeated START conditions
(Sr).
HS mode (current-source for SCL HIGH enabled)
F/S mode
F/S mode
S
MASTER CODE
A
Sr SLAVE ADDRESS R/W
A
DATA
A/A
P
(n-bytes + A)
HS mode continues
SLAVE ADDRESS
Sr
001aak749
Fig 24. I2C-bus HS mode protocol switch
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
80 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
t
1
A
8-bit master code 0000 1xxx
S
t
H
SDA high
SCL high
1
2 to 5
6
7
8
9
F/S mode
n + (8-bit data
+
A/A)
R/W
A
7-bit SLA
Sr
Sr P
SDA high
SCL high
1
2 to 5
6
7
8
9
1
2 to 5
6
7
8
9
If P then
HS mode
F/S mode
If Sr (dotted lines)
then HS mode
t
H
t
FS
= Master current source pull-up
= Resistor pull-up
msc618
Fig 25. I2C-bus HS mode protocol frame
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
81 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
10.4.11 Switching between F/S mode and HS mode
After reset and initialization, the PN512 is in Fast mode (which is in effect F/S mode as
Fast mode is downward-compatible with Standard mode). The connected PN512
recognizes the “S 00001XXX A” sequence and switches its internal circuitry from the Fast
mode setting to the HS mode setting.
The following actions are taken:
1. Adapt the SDA and SCL input filters according to the spike suppression requirement
in HS mode.
2. Adapt the slope control of the SDA output stages.
It is possible for system configurations that do not have other I2C-bus devices involved in
the communication to switch to HS mode permanently. This is implemented by setting
Status2Reg register’s I2CForceHS bit to logic 1. In permanent HS mode, the master code
is not required to be sent. This is not defined in the specification and must only be used
when no other devices are connected on the bus. In addition, spikes on the I2C-bus lines
must be avoided because of the reduced spike suppression.
10.4.12 PN512 at lower speed modes
PN512 is fully downward-compatible and can be connected to an F/S mode I2C-bus
system. The device stays in F/S mode and communicates at F/S mode speeds because a
master code is not transmitted in this configuration.
11. 8-bit parallel interface
The PN512 supports two different types of 8-bit parallel interfaces, Intel and Motorola
compatible modes.
11.1 Overview of supported host controller interfaces
The PN512 supports direct interfacing to various -Controllers. The following table shows
the parallel interface types supported by the PN512.
Table 152. Supported interface types
Supported interface types Bus
Separated Address and Multiplexed Address
Data Bus
and Data Bus
NRD, NWR, NCS, ALE
AD0 … AD7
Separated Read and Write
Strobes (INTEL compatible)
control
NRD, NWR, NCS
A0 … A3 [..A5*]
D0 … D7
address
data
AD0 … AD7
Multiplexed Read and Write control
R/NW, NDS, NCS
A0 … A3 [..A5*]
D0 … D7
R/NW, NDS, NCS, AS
AD0 … AD7
Strobe (Motorola compatible)
address
data
AD0 … AD7
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
82 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
11.2 Separated Read/Write strobe
non multiplexed
address
PN512
PN512
address bus
ADDRESS
DECODER
ADDRESS
DECODER
NCS
NCS
low
A5*
A4*
A3
low
address bus (A0...A3[A5*])
data bus (D0...D7)
low
A0...A3[A5*]
D0...D7
high
high
high
A2
A1
A0
multiplexed address/data AD0...AD7)
high
D0...D7
ALE
address latch enable (ALE)
not read strobe (NRD)
not write (NWR)
not data strobe (NRD)
not write (NWR)
ALE
NRD
NWR
NRD
NWR
remark: *depending on the package type.
001aan223
Fig 26. Connection to host controller with separated Read/Write strobes
For timing requirements refer to Section 26.2 “8-bit parallel interface timing”.
11.3 Common Read/Write strobe
non multiplexed
address
PN512
PN512
address bus
ADDRESS
DECODER
ADDRESS
DECODER
NCS
NCS
low
low
low
high
high
low
A5*
A4*
A3
address bus (A0...A3[A5*])
Data bus (D0...D7)
A0...A3[A5*]
D0...D7
A2
A1
A0
multiplexed address/data AD0...AD7)
high
D0...D7
ALE
address strobe (AS)
not data strobe (NDS)
read not write (RD/NWR)
ALE
NRD
NWR
not data strobe (NDS)
read not write (RD/NWR)
NRD
NWR
remark: *depending on the package type.
001aan224
Fig 27. Connection to host controller with common Read/Write strobes
For timing requirements refer to Section 26.2 “8-bit parallel interface timing”
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
83 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
12. Analog interface and contactless UART
12.1 General
The integrated contactless UART supports the external host online with framing and error
checking of the protocol requirements up to 848 kBd. An external circuit can be connected
to the communication interface pins MFIN and MFOUT to modulate and demodulate the
data.
The contactless UART handles the protocol requirements for the communication
protocols in cooperation with the host. Protocol handling generates bit and byte-oriented
framing. In addition, it handles error detection such as parity and CRC, based on the
various supported contactless communication protocols.
Remark: The size and tuning of the antenna and the power supply voltage have an
important impact on the achievable operating distance.
12.2 TX driver
The signal on pins TX1 and TX2 is the 13.56 MHz energy carrier modulated by an
envelope signal. It can be used to drive an antenna directly using a few passive
components for matching and filtering; see Section 15 on page 96. The signal on pins TX1
and TX2 can be configured using the TxControlReg register; see Section 9.2.2.5 on
page 40.
The modulation index can be set by adjusting the impedance of the drivers. The
impedance of the p-driver can be configured using registers CWGsPReg and
ModGsPReg. The impedance of the n-driver can be configured using the GsNReg
register. The modulation index also depends on the antenna design and tuning.
The TxModeReg and TxSelReg registers control the data rate and framing during
transmission and the antenna driver setting to support the different requirements at the
different modes and transfer speeds.
Table 153. Register and bit settings controlling the signal on pin TX1
Bit
Tx1RFEn Force
100ASK
Bit
Bit
Bit
Envelope Pin
TX1
GSPMos
GSNMos
Remarks
InvTx1RFOn InvTx1RFOff
0
X[1]
X[1]
0
X[1]
X[1]
X[1]
X[1]
CWGsNOff CWGsNOff not specified if RF is
switched off
1
0
0
1
0
1
0
1
0
1
RF
RF
RF
RF
0
pMod
pCW
pMod
pCW
pMod
nMod
nCW
nMod
nCW
nMod
nCW
100 % ASK: pin TX1
pulled to logic 0,
independent of the
InvTx1RFOff bit
1
1
X[1]
X[1]
RF_n pCW
[1] X = Do not care.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
84 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 154. Register and bit settings controlling the signal on pin TX2
Bit
Tx1RFEn Force
100ASK
Bit
Bit
Bit
Bit
En-
Pin
GSPMos
GSNMos
Remarks
Tx2CW InvTx2RFOn InvTx2RFOff velope TX2
0
X[1]
X[1]
X[1]
X[1]
X[1]
X[1]
CWGsNOff CWGsNOff not specified if
RF is switched
off
1
0
0
0
1
X[1]
X[1]
0
RF
RF
pMod
pCW
nMod
nCW
nMod
nCW
nCW
nCW
-
1
0
RF_n pMod
RF_n pCW
1
1
0
0
1
X[1]
X[1]
X[1]
X[1]
RF
pCW
conductance
always CW for
the Tx2CW bit
RF_n pCW
1
0
1
X[1]
X[1]
0
0
pMod
pCW
pMod
nMod
nCW
nMod
nCW
nCW
nCW
100 % ASK: pin
TX2 pulled
to logic 0
(independent of
the
InvTx2RFOn/In
vTx2RFOff bits)
1
RF
0
0
1
RF_n pCW
RF pCW
RF_n pCW
1
0
1
X[1]
X[1]
X[1]
X[1]
[1] X = Do not care.
The following abbreviations have been used in Table 153 and Table 154:
• RF: 13.56 MHz clock derived from 27.12 MHz quartz crystal oscillator divided by 2
• RF_n: inverted 13.56 MHz clock
• GSPMos: conductance, configuration of the PMOS array
• GSNMos: conductance, configuration of the NMOS array
• pCW: PMOS conductance value for continuous wave defined by the CWGsPReg
register
• pMod: PMOS conductance value for modulation defined by the ModGsPReg register
• nCW: NMOS conductance value for continuous wave defined by the GsNReg
register’s CWGsN[3:0] bits
• nMod: NMOS conductance value for modulation defined by the GsNReg register’s
ModGsN[3:0] bits
• X = do not care.
Remark: If only one driver is switched on, the values for CWGsPReg, ModGsPReg and
GsNReg registers are used for both drivers.
12.3 RF level detector
The RF level detector is integrated to fulfill NFCIP1 protocol requirements (e.g. RF
collision avoidance). Furthermore the RF level detector can be used to wake up the
PN512 and to generate an interrupt.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
85 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
The sensitivity of the RF level detector is adjustable in a 4-bit range using the bits RFLevel
in register RFCfgReg. The sensitivity itself depends on the antenna configuration and
tuning.
Possible sensitivity levels at the RX pin are listed in the Table 154.
Table 155. Setting of the bits RFlevel in register RFCfgReg (RFLevel amplifier deactivated)
V~Rx [Vpp]
~2
RFLevel
1111
~1.4
1110
1101
1100
1011
1010
1001
1000
0111
0110
0101
0100
0011
0010
0001
0000
~0.99
~0.69
~0.49
~0.35
~0.24
~0.17
~0.12
~0.083
~0.058
~0.041
~0.029
~0.020
~0.014
~0.010
To increase the sensitivity of the RF level detector an amplifier can be activated by setting
the bit RFLevelAmp in register RFCfgReg to 1.
Remark: During soft Power-down mode the RF level detector amplifier is automatically
switched off to ensure that the power consumption is less than 10 A at 3 V.
Remark: With typical antennas lower sensitivity levels can provoke misleading results
because of intrinsic noise in the environment.
Note: It is recommended to use the bit RFLevelAmp only with higher RF level settings.
12.4 Data mode detector
The Data mode detector gives the possibility to detect received signals according to the
ISO/IEC 14443A/MIFARE, FeliCa or NFCIP-1 schemes at the standard transfer speeds
for 106 kbit, 212 kbit and 424 kbit in order to prepare the internal receiver in a fast and
convenient way for further data processing.
The Data mode detector can only be activated by the AutoColl command. The mode
detector resets, when no external RF field is detected by the RF level detector. The Data
mode detector could be switched off during the AutoColl command by setting bit
ModeDetOff in register ModeReg to 1.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
86 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
HOST INTERFACES
REGISTERS
REGISTERSETTING
FOR THE
DETECTED MODE
NFC @ 106 kbit/s
NFC @ 212 kbit/s
NFC @ 424 kbit/s
DATA MODE DETECTOR
RECEIVER
I/Q DEMODULATOR
PN512
RX
001aan225
Fig 28. Data mode detector
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
87 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
12.5 Serial data switch
Two main blocks are implemented in the PN512. The digital block comprises the state
machines, encoder/decoder logic. The analog block comprises the modulator and
antenna drivers, the receiver and amplifiers. The interface between these two blocks can
be configured in the way, that the interfacing signals may be routed to the pins SIGIN and
SIGOUT. SIGIN is capable of processing digital NFC signals on transfer speeds above
424 kbit. The SIGOUT pin can provide a digital signal that can be used with an additional
external circuit to generate transfer speeds above 424 kbit (including 106, 212 and
424 kbit). Furthermore SIGOUT and SIGIN can be used to enable the S2C interface in the
card SAM mode to emulate a card functionality with the PN512 and a secure IC. A secure
IC can be the SmartMX smart card controller IC.
This topology allows the analog block of the PN512 to be connected to the digital block of
another device.
The serial signal switch is controlled by the TxSelReg and RxSelReg registers.
Figure 29 shows the serial data switch for TX1 and TX2.
DriverSel[1:0]
3-state
1
00
01
10
11
envelope
INTERNAL
CODER
INVERT IF
InvMod = 1
to driver TX1 and TX2
0 = impedance = modulated
1 = impedance = CW
INVERT IF
PolMFin = 0
MFIN
001aak593
Fig 29. Serial data switch for TX1 and TX2
12.6 S2C interface support
The S2C provides the possibility to directly connect a secure IC to the PN512 in order act
as a contactless smart card IC via the PN512. The interfacing signals can be routed to the
pins SIGIN and SIGOUT. SIGIN can receive either a digital FeliCa or digitized
ISO/IEC 14443A signal sent by the secure IC. The SIGOUT pin can provide a digital
signal and a clock to communicate to the secure IC. A secure IC can be the smart card IC
provided by NXP Semiconductors.
The PN512 has an extra supply pin (SVDD and PVSS as Ground line) for the SIGIN and
SIGOUT pads.
Figure 31 outlines possible ways of communications via the PN512 to the secure IC.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
88 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
HOST CONTROLLER
PN512
1. secure access
module (SAM) mode
2
SPI, I C, SERIAL UART
FIFO AND STATE MACHINE
SERIAL SIGNAL SWITCH
CONTACTLESS UART
SIGOUT
SIGIN
SECURE CORE IC
2. contactless
card mode
001aan226
Fig 30. Communication flows using the S2C interface
Configured in the Secure Access Mode the host controller can directly communicate to
the Secure IC via SIGIN/SIGOUT. In this mode the PN512 generates the RF clock and
performs the communication on the SIGOUT line. To enable the Secure Access module
mode the clock has to be derived by the internal oscillator of the PN512, see bits
SAMClockSel in register TestSel1Reg.
Configured in Contactless Card mode the secure IC can act as contactless smart card IC
via the PN512. In this mode the signal on the SIGOUT line is provided by the external RF
field of the external reader/writer. To enable the Contactless Card mode the clock derived
by the external RF field has to be used.
The configuration of the S2C interface differs for the FeliCa and MIFARE scheme as
outlined in the following chapters.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
89 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
12.6.1 Signal shape for Felica S2C interface support
The FeliCa secure IC is connected to the PN512 via the pins SIGOUT and SIGIN.
The signal at SIGOUT contains the information of the 13.56 MHz clock and the digitized
demodulated signal. The clock and the demodulated signal is combined by using the
logical function exclusive or.
To ensure that this signal is free of spikes, the demodulated signal is digitally filtered first.
The time delay for that digital filtering is in the range of one bit length. The demodulated
signal changes only at a positive edge of the clock.
The register TxSelReg controls the setting at SIGOUT.
clock
signal on
SIGIN
signal on
antenna
001aan227
Fig 31. Signal shape for SIGOUT in FeliCa card SAM mode
The answer of the FeliCa SAM is transferred from SIGIN directly to the antenna driver.
The modulation is done according to the register settings of the antenna drivers.
The clock is switched to AUX1 or AUX2 (see AnalogSelAux).
Note: A HIGH signal on AUX1 and AUX2 has the same level as AVDD. A HIGH signal at
SIGOUT has the same level as SVDD. Alternatively it is possible to use pin D0 as clock
output if a serial interface is used. The HIGH level at D0 is the same as PVDD.
clock
demodulated
signal
signal on
SIGOUT
001aan228
Fig 32. Signal shape for SIGIN in SAM mode
Note: The signal on the antenna is shown in principle only. In reality the waveform is
sinusoidal.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
90 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
12.6.2 Waveform shape for ISO/IEC 14443A and MIFARE S2C support
The secure IC, e.g. the SmartMX is connected to the PN512 via the pins SIGOUT and
SIGIN.
The waveform shape at SIGOUT is a digital 13.56 MHz Miller coded signal with levels
between PVSS and PVDD derived out of the external 13.56 MHz carrier signal in case of
the Contactless Card mode or internally generated in terms of Secure Access mode.
The register TxSelReg controls the setting at SIGOUT.
Note: The clock settings for the Secure Access mode and the Contactless Card mode
differ, refer to the description of the bits SAMClockSel in register TestSel1Reg.
0
1
0
0
1
bit
value RF
signal on
antenna
1
0
signal on
SIGOUT
001aan229
Fig 33. Signal shape for SIGOUT in MIFARE Card SAM mode
The signal at SIGIN is a digital Manchester coded signal according to the requirements of
the ISO/IEC 14443A with the subcarrier frequency of 847.5 kHz generated by the secure
IC.
bit
value
0
1
0
0
1
signal on
antenna
1
0
signal on
SIGIN
001aan230
Fig 34. Signal shape for SIGIN in MIFARE Card SAM mode
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
91 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
12.7 Hardware support for FeliCa and NFC polling
12.7.1 Polling sequence functionality for initiator
1. Timer: The PN512 has a timer, which can be programmed in a way that it generates
an interrupt at the end of each timeslot, or if required an interrupt is generated at the
end of the last timeslot.
2. The receiver can be configured in a way to receive continuously. In this mode it can
receive any number of packets. The receiver is ready to receive the next packet
directly after the last packet has been received. This mode is active by setting the bit
RxMultiple in register RxModeReg to 1 and has to be stopped by software.
3. The internal UART adds one byte to the end of every received packet, before it is
transferred into the FIFO-buffer. This byte indicates if the received byte packet is
correct (see register ErrReg). The first byte of each packet contains the length byte of
the packet.
4. The length of one packet is 18 or 20 bytes (+ 1 byte Error-Info). The FIFO has a
length of 64 bytes. This means three packets can be stored in the FIFO at the same
time. If more than three packets are expected, the host controller has to empty the
FIFO, before the FIFO is filled completely. In case of a FIFO-overflow data is lost (See
bit BufferOvfl in register ErrorReg).
12.7.2 Polling sequence functionality for target
1. The host controller has to configure the PN512 with the correct polling response
parameters for the polling command.
2. To activate the automatic polling in Target mode, the AutoColl Command has to be
activated.
3. The PN512 receives the polling command send out by an initiator and answers with
the polling response. The timeslot is selected automatically (The timeslot itself is
randomly generated, but in the range 0 to TSN, which is defined by the Polling
command). The PN512 compares the system code, stored in byte 17 and 18 of the
Config Command with the system code received by the polling command of an
initiator. If the system code is equal, the PN512 answers according to the configured
polling response. The system code FF (hex) acts as a wildcard for the system code
bytes, i.e. a target of a system code 1234 (hex) answers to the polling command with
one of the following system codes 1234 (hex), 12FF (hex), FF34 (hex) or FFFF (hex).
If the system code does not match no answer is sent back by the PN512.
If a valid command is received by the PN512, which is not a Polling command, no
answer is sent back and the command AutoColl is stopped. The received packet is
stored in the FIFO.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
92 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
12.7.3 Additional hardware support for FeliCa and NFC
Additionally to the polling sequence support for the Felica mode, the PN512 supports the
check of the Len-byte.
The received Len-byte in accordance to the registers FelNFC1Reg and FelNFC2Reg:
DataLenMin in register FelNFC1Reg defines the minimum length of the accepted packet
length. This register is six bit long. Each bit represents a length of four bytes.
DataLenMax in register FelNFC2Reg defines the maximum length of the accepted
package. This register is six bit long. Each bit represents a length of four bytes. If set to
logic 1 this limit is ignored. If the length is not in the supposed range, the packet is not
transferred to the FIFO and receiving is kept active.
Example 1:
• DataLenMin = 4
– The length shall be greater or equal 16.
• DataLenMax = 5
– The length shall be smaller than 20. Valid area: 16, 17, 18, 19
Example 2:
• DataLenMin = 9
– The length shall be greater or equal 36.
• DataLenMax = 0
– The length shall be smaller than 256. Valid area: 36 to 255
12.7.4 CRC coprocessor
The following CRC coprocessor parameters can be configured:
• The CRC preset value can be either 0000h, 6363h, A671h or FFFFh depending on
the ModeReg register’s CRCPreset[1:0] bits setting
• The CRC polynomial for the 16-bit CRC is fixed to x16 + x12 + x5 + 1
• The CRCResultReg register indicates the result of the CRC calculation. This register
is split into two 8-bit registers representing the higher and lower bytes.
• The ModeReg register’s MSBFirst bit indicates that data will be loaded with the MSB
first.
Table 156. CRC coprocessor parameters
Parameter
Value
CRC register length
CRC algorithm
CRC preset value
16-bit CRC
algorithm according to ISO/IEC 14443 A and ITU-T
0000h, 6363h, A671h or FFFFh depending on the setting of the
ModeReg register’s CRCPreset[1:0] bits
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
93 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
13. FIFO buffer
An 8 64 bit FIFO buffer is used in the PN512. It buffers the input and output data stream
between the host and the PN512’s internal state machine. This makes it possible to
manage data streams up to 64 bytes long without the need to take timing constraints into
account.
13.1 Accessing the FIFO buffer
The FIFO buffer input and output data bus is connected to the FIFODataReg register.
Writing to this register stores one byte in the FIFO buffer and increments the internal FIFO
buffer write pointer. Reading from this register shows the FIFO buffer contents stored in
the FIFO buffer read pointer and decrements the FIFO buffer read pointer. The distance
between the write and read pointer can be obtained by reading the FIFOLevelReg
register.
When the microcontroller starts a command, the PN512 can, while the command is in
progress, access the FIFO buffer according to that command. Only one FIFO buffer has
been implemented which can be used for input and output. The microcontroller must
ensure that there are not any unintentional FIFO buffer accesses.
13.2 Controlling the FIFO buffer
The FIFO buffer pointers can be reset by setting FIFOLevelReg register’s FlushBuffer bit
to logic 1. Consequently, the FIFOLevel[6:0] bits are all set to logic 0 and the ErrorReg
register’s BufferOvfl bit is cleared. The bytes stored in the FIFO buffer are no longer
accessible allowing the FIFO buffer to be filled with another 64 bytes.
13.3 FIFO buffer status information
The host can get the following FIFO buffer status information:
• Number of bytes stored in the FIFO buffer: FIFOLevelReg register’s FIFOLevel[6:0]
• FIFO buffer almost full warning: Status1Reg register’s HiAlert bit
• FIFO buffer almost empty warning: Status1Reg register’s LoAlert bit
• FIFO buffer overflow warning: ErrorReg register’s BufferOvfl bit. The BufferOvfl bit
can only be cleared by setting the FIFOLevelReg register’s FlushBuffer bit.
The PN512 can generate an interrupt signal when:
• ComIEnReg register’s LoAlertIEn bit is set to logic 1. It activates pin IRQ when
Status1Reg register’s LoAlert bit changes to logic 1.
• ComIEnReg register’s HiAlertIEn bit is set to logic 1. It activates pin IRQ when
Status1Reg register’s HiAlert bit changes to logic 1.
If the maximum number of WaterLevel bytes (as set in the WaterLevelReg register) or less
are stored in the FIFO buffer, the HiAlert bit is set to logic 1. It is generated according to
Equation 3:
HiAlert = 64 – FIFOLength WaterLevel
(3)
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
94 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
If the number of WaterLevel bytes (as set in the WaterLevelReg register) or less are
stored in the FIFO buffer, the LoAlert bit is set to logic 1. It is generated according to
Equation 4:
LoAlert = FIFOLength WaterLevel
(4)
14. Interrupt request system
The PN512 indicates certain events by setting the Status1Reg register’s IRq bit and, if
activated, by pin IRQ. The signal on pin IRQ can be used to interrupt the host using its
interrupt handling capabilities. This allows the implementation of efficient host software.
14.1 Interrupt sources overview
Table 157 shows the available interrupt bits, the corresponding source and the condition
for its activation. The ComIrqReg register’s TimerIRq interrupt bit indicates an interrupt set
by the timer unit which is set when the timer decrements from 1 to 0.
The ComIrqReg register’s TxIRq bit indicates that the transmitter has finished. If the state
changes from sending data to transmitting the end of the frame pattern, the transmitter
unit automatically sets the interrupt bit. The CRC coprocessor sets the DivIrqReg
register’s CRCIRq bit after processing all the FIFO buffer data which is indicated by
CRCReady bit = 1.
The ComIrqReg register’s RxIRq bit indicates an interrupt when the end of the received
data is detected. The ComIrqReg register’s IdleIRq bit is set if a command finishes and
the Command[3:0] value in the CommandReg register changes to idle (see Table 158 on
page 101).
The ComIrqReg register’s HiAlertIRq bit is set to logic 1 when the Status1Reg register’s
HiAlert bit is set to logic 1 which means that the FIFO buffer has reached the level
indicated by the WaterLevel[5:0] bits.
The ComIrqReg register’s LoAlertIRq bit is set to logic 1 when the Status1Reg register’s
LoAlert bit is set to logic 1 which means that the FIFO buffer has reached the level
indicated by the WaterLevel[5:0] bits.
The ComIrqReg register’s ErrIRq bit indicates an error detected by the contactless UART
during send or receive. This is indicated when any bit is set to logic 1 in register ErrorReg.
Table 157. Interrupt sources
Interrupt flag Interrupt source
Trigger action
TimerIRq
TxIRq
timer unit
the timer counts from 1 to 0
a transmitted data stream ends
all data from the FIFO buffer has been processed
a received data stream ends
command execution finishes
the FIFO buffer is almost full
the FIFO buffer is almost empty
an error is detected
transmitter
CRCIRq
RxIRq
CRC coprocessor
receiver
IdleIRq
ComIrqReg register
FIFO buffer
HiAlertIRq
LoAlertIRq
ErrIRq
FIFO buffer
contactless UART
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
95 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
15. Timer unit
A timer unit is implemented in the PN512. The external host controller may use this timer
to manage timing relevant tasks. The timer unit may be used in one of the following
configurations:
• Time-out counter
• Watch-dog counter
• Stop watch
• Programmable one-shot
• Periodical trigger
The timer unit can be used to measure the time interval between two events or to indicate
that a specific event occurred after a specific time. The timer can be triggered by events
which will be explained in the following, but the timer itself does not influence any internal
event (e.g. A time-out during data reception does not influence the reception process
automatically). Furthermore, several timer related bits are set and these bits can be used
to generate an interrupt.
Timer
The timer has an input clock of 13.56 MHz (derived from the 27.12 MHz quartz). The timer
consists of two stages: 1 prescaler and 1 counter.
The prescaler is a 12-bit counter. The reload value for TPrescaler can be defined between
0 and 4095 in register TModeReg and TPrescalerReg.
The reload value for the counter is defined by 16 bits in a range of 0 to 65535 in the
register TReloadReg.
The current value of the timer is indicated by the register TCounterValReg.
If the counter reaches 0 an interrupt will be generated automatically indicated by setting
the TimerIRq bit in the register CommonIRqReg. If enabled, this event can be indicated on
the IRQ line. The bit TimerIRq can be set and reset by the host controller. Depending on
the configuration the timer will stop at 0 or restart with the value from register
TReloadReg.
The status of the timer is indicated by bit TRunning in register Status1Reg.
The timer can be manually started by TStartNow in register ControlReg or manually
stopped by TStopNow in register ControlReg.
Furthermore the timer can be activated automatically by setting the bit TAuto in the
register TModeReg to fulfill dedicated protocol requirements automatically.
The time delay of a timer stage is the reload value +1.
The definition of total time is: t = ((TPrescaler*2+1)*TReload+1)/13.56MHz or if
TPrescaleEven bit is set: t = ((TPrescaler*2+2)*TReload+1)/13.56MHz
Maximum time: TPrescaler = 4095,TReloadVal = 65535
=> (2*4095 +2)*65536/13.56 MHz = 39.59 s
Example:
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
96 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
To indicate 25 us it is required to count 339 clock cycles. This means the value for
TPrescaler has to be set to TPrescaler = 169.The timer has now an input clock of 25 us.
The timer can count up to 65535 timeslots of each 25 s. For the behaviour in version
1.0, see Section 21 “Errata sheet” on page 109.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
97 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
16. Power reduction modes
16.1 Hard power-down
Hard power-down is enabled when pin NRSTPD is LOW. This turns off all internal current
sinks including the oscillator. All digital input buffers are separated from the input pins and
clamped internally (except pin NRSTPD). The output pins are frozen at either a HIGH or
LOW level.
16.2 Soft power-down mode
Soft Power-down mode is entered immediately after the CommandReg register’s
PowerDown bit is set to logic 1. All internal current sinks are switched off, including the
oscillator buffer. However, the digital input buffers are not separated from the input pins
and keep their functionality. The digital output pins do not change their state.
During soft power-down, all register values, the FIFO buffer content and the configuration
keep their current contents.
After setting the PowerDown bit to logic 0, it takes 1024 clocks until the Soft power-down
mode is exited indicated by the PowerDown bit. Setting it to logic 0 does not immediately
clear it. It is cleared automatically by the PN512 when Soft power-down mode is exited.
Remark: If the internal oscillator is used, you must take into account that it is supplied by
pin AVDD and it will take a certain time (tosc) until the oscillator is stable and the clock
cycles can be detected by the internal logic. It is recommended for the serial UART, to first
send the value 55h to the PN512. The oscillator must be stable for further access to the
registers. To ensure this, perform a read access to address 0 until the PN512 answers to
the last read command with the register content of address 0. This indicates that the
PN512 is ready.
16.3 Transmitter power-down mode
The Transmitter Power-down mode switches off the internal antenna drivers thereby,
turning off the RF field. Transmitter power-down mode is entered by setting either the
TxControlReg register’s Tx1RFEn bit or Tx2RFEn bit to logic 0.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
98 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
17. Oscillator circuitry
PN512
OSCOUT
OSCIN
27.12 MHz
001aan231
Fig 35. Quartz crystal connection
The clock applied to the PN512 provides a time basis for the synchronous system’s
encoder and decoder. The stability of the clock frequency, therefore, is an important factor
for correct operation. To obtain optimum performance, clock jitter must be reduced as
much as possible. This is best achieved using the internal oscillator buffer with the
recommended circuitry.
If an external clock source is used, the clock signal must be applied to pin OSCIN. In this
case, special care must be taken with the clock duty cycle and clock jitter and the clock
quality must be verified.
18. Reset and oscillator start-up time
18.1 Reset timing requirements
The reset signal is filtered by a hysteresis circuit and a spike filter before it enters the
digital circuit. The spike filter rejects signals shorter than 10 ns. In order to perform a reset,
the signal must be LOW for at least 100 ns.
18.2 Oscillator start-up time
If the PN512 has been set to a Power-down mode or is powered by a VDDX supply, the
start-up time for the PN512 depends on the oscillator used and is shown in Figure 36.
The time (tstartup) is the start-up time of the crystal oscillator circuit. The crystal oscillator
start-up time is defined by the crystal.
The time (td) is the internal delay time of the PN512 when the clock signal is stable before
the PN512 can be addressed.
The delay time is calculated by:
1024
27 s
-------------
td
=
= 37.74 s
(5)
The time (tosc) is the sum of td and tstartup
.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
99 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
device activation
oscillator
clock stable
clock ready
t
startup
t
d
t
osc
t
001aak596
Fig 36. Oscillator start-up time
19. PN512 command set
The PN512 operation is determined by a state machine capable of performing a set of
commands. A command is executed by writing a command code (see Table 158) to the
CommandReg register.
Arguments and/or data necessary to process a command are exchanged via the FIFO
buffer.
19.1 General description
The PN512 operation is determined by a state machine capable of performing a set of
commands. A command is executed by writing a command code (see Table 158) to the
CommandReg register.
Arguments and/or data necessary to process a command are exchanged via the FIFO
buffer.
19.2 General behavior
• Each command that needs a data bit stream (or data byte stream) as an input
immediately processes any data in the FIFO buffer. An exception to this rule is the
Transceive command. Using this command, transmission is started with the
BitFramingReg register’s StartSend bit.
• Each command that needs a certain number of arguments, starts processing only
when it has received the correct number of arguments from the FIFO buffer.
• The FIFO buffer is not automatically cleared when commands start. This makes it
possible to write command arguments and/or the data bytes to the FIFO buffer and
then start the command.
• Each command can be interrupted by the host writing a new command code to the
CommandReg register, for example, the Idle command.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
100 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
19.3 PN512 command overview
Table 158. Command overview
Command
Command Action
code
0000
0001
Idle
no action, cancels current command execution
Configure
Configures the PN512 for FeliCa, MIFARE and NFCIP-1
communication
Generate RandomID 0010
generates a 10-byte random ID number
activates the CRC coprocessor or performs a self test
transmits data from the FIFO buffer
CalcCRC
0011
0100
0111
Transmit
NoCmdChange
no command change, can be used to modify the
CommandReg register bits without affecting the command,
for example, the PowerDown bit
Receive
1000
1100
activates the receiver circuits
Transceive
transmits data from FIFO buffer to antenna and automatically
activates the receiver after transmission
AutoColl
1101
Handles FeliCa polling (Card Operation mode only) and
MIFARE anticollision (Card Operation mode only)
MFAuthent
SoftReset
1110
1111
performs the MIFARE standard authentication as a reader
resets the PN512
19.3.1 PN512 command descriptions
19.3.1.1 Idle
Places the PN512 in Idle mode. The Idle command also terminates itself.
19.3.1.2 Config command
To use the automatic MIFARE Anticollision, FeliCa Polling and NFCID3 the data used for
these transactions has to be stored internally. All the following data have to be written to
the FIFO in this order:
SENS_RES (2 bytes); in order byte 0, byte 1
NFCID1 (3 Bytes); in order byte 0, byte 1, byte 2; the first NFCID1 byte is fixed to 08h and
the check byte is calculated automatically.
SEL_RES (1 Byte)
polling response (2 bytes (shall be 01h, FEh) + 6 bytes NFCID2 + 8 bytes Pad + 2 bytes
system code)
NFCID3 (1 byte)
In total 25 bytes are transferred into an internal buffer.
The complete NFCID3 is 10 bytes long and consists of the 3 NFCID1 bytes, the 6 NFCID2
bytes and the one NFCID3 byte which are listed above.
To read out this configuration the command Config with an empty FIFO-buffer has to be
started. In this case the 25 bytes are transferred from the internal buffer to the FIFO.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
101 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
The PN512 has to be configured after each power up, before using the automatic
Anticollision/Polling function (AutoColl command). During a hard power down (reset pin)
this configuration remains unchanged.
This command terminates automatically when finished and the active command is idle.
19.3.1.3 Generate RandomID
This command generates a 10-byte random number which is initially stored in the internal
buffer. This then overwrites the 10 bytes in the internal 25-byte buffer. This command
automatically terminates when finished and the PN512 returns to Idle mode.
19.3.1.4 CalcCRC
The FIFO buffer content is transferred to the CRC coprocessor and the CRC calculation is
started. The calculation result is stored in the CRCResultReg register. The CRC
calculation is not limited to a dedicated number of bytes. The calculation is not stopped
when the FIFO buffer is empty during the data stream. The next byte written to the FIFO
buffer is added to the calculation.
The CRC preset value is controlled by the ModeReg register’s CRCPreset[1:0] bits. The
value is loaded in to the CRC coprocessor when the command starts.
This command must be terminated by writing a command to the CommandReg register,
such as, the Idle command.
If the AutoTestReg register’s SelfTest[3:0] bits are set correctly, the PN512 enters Self
Test mode. Starting the CalcCRC command initiates a digital self test. The result of the
self test is written to the FIFO buffer.
19.3.1.5 Transmit
The FIFO buffer content is immediately transmitted after starting this command. Before
transmitting the FIFO buffer content, all relevant registers must be set for data
transmission.
This command automatically terminates when the FIFO buffer is empty. It can be
terminated by another command written to the CommandReg register.
19.3.1.6 NoCmdChange
This command does not influence any running command in the CommandReg register. It
can be used to manipulate any bit except the CommandReg register Command[3:0] bits,
for example, the RcvOff bit or the PowerDown bit.
19.3.1.7 Receive
The PN512 activates the receiver path and waits for a data stream to be received. The
correct settings must be chosen before starting this command.
This command automatically terminates when the data stream ends. This is indicated
either by the end of frame pattern or by the length byte depending on the selected frame
type and speed.
Remark: If the RxModeReg register’s RxMultiple bit is set to logic 1, the Receive
command will not automatically terminate. It must be terminated by starting another
command in the CommandReg register.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
102 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
19.3.1.8 Transceive
This command continuously repeats the transmission of data from the FIFO buffer and the
reception of data from the RF field. The first action is transmit and after transmission the
command is changed to receive a data stream.
Each transmit process must be started by setting the BitFramingReg register’s StartSend
bit to logic 1. This command must be cleared by writing any command to the
CommandReg register.
Remark: If the RxModeReg register’s RxMultiple bit is set to logic 1, the Transceive
command never leaves the receive state because this state cannot be cancelled
automatically.
19.3.1.9 AutoColl
This command automatically handles the MIFARE activation and the FeliCa polling in the
Card Operation mode. The bit Initiator in the register ControlReg has to be set to logic 0
for correct operation. During this command also the mode detector is active if not
deactivated by setting the bit ModeDetOff in the ModeReg register. After the mode
detector detects a mode, all the mode dependent registers are set according to the
received data. In case of no external RF field the command resets the internal state
machine and returns to the initial state but it will not be terminated. When the command
terminates the transceive command gets active.
During protocol processing the IRQ bits are not supported. Only the last received frame
will serve the IRQ’s. The treatment of the TxCRCEn and RxCRCEn bits is different to the
protocol. During ISO/IEC 14443A activation the enable bits are defined by the command
AutoColl. The changes cannot be observed at the register TXModeReg and RXModeReg.
After the Transceive command is active, the value of the register bit is relevant.
The FIFO will also receive the two CRC check bytes of the last command even if they
already checked and correct, if the state machine (Anticollision and Select routine) has to
not been executed and 106 kbit is detected.
During Felica activation the register bit is always relevant and is not overruled by the
command settings. This command can be cleared by software by writing any other
command to the CommandReg register, e.g. the idle command. Writing the same content
again to the CommandReg register resets the state machine.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
103 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
MODE
detection
RXF
raming
00
10
NFCIP-1 106 kB aud
ISO14443-3
NPCIP-1 > 106 kB aud
FELICA
J
MFHalted = 1
N
REQA,
AC,
nAC,
SELECT,
nSELECT,
HLTA
AC
nAC
SELECT
nSELECT
HLTA
polling,
polling response
HALT
IDLE
MODEO
REQA,
WUPA,
nAC,
nSELECT,
HLTA,
error
REQA,
WUPA,
nAC,
nSELECT,
HLTA,
WUPA
REQA, WUPA
REQA,
WUPA,
AC,
REQA,
WUPA,
AC,
error
nAC,
SELECT,
nSELECT,
error
SELECT,
nSELECT,
error
READY*
SELECT
READY
AC
AC
SELECT
ACTIVE*
ACTIVE
HLTA
next frame
received
next frame
received
next frame
received
TRANSCEIVE
wait for
transmit
aaa-001826
Fig 37. Autocoll Command
NFCIP-1 106 kbps Passive Communication mode:
The MIFARE anticollision is finished and the command has automatically changed to
Transceive. The FIFO contains the ATR_REQ frame including the start byte F0h. The bit
TargetActivated in the Status2Reg register is set to logic 1.
NFCIP-1 212/424 kbps Passive Communication mode:
The FeliCa polling command is finished and the command has automatically changed to
Transceive. The FIFO contains the ATR_REQ. The bit TargetActivated in the Status2Reg
register is set to logic 1.
NFCIP-1 106/212/424 kbps Active Communication mode:
This command is changing the automatically to the command Transceive. The FIFO
contains the ATR REQ The bit TargetActivated in the Status2Reg register is set to logic 0.
For 106 kbps only, the first byte in the FIFO indicates the start byte F0h and the CRC is
added to the FIFO.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
104 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
MIFARE (Card Operation mode):
The MIFARE anticollision is finished and the command has automatically changed to
transceive. The FIFO contains the first command after the Select. The bit TargetActivated
in the Status2Reg register is set to logic 1.
Felica (Card Operation mode):
The FeliCa polling command is finished and the command has automatically changed to
transceive. The FIFO contains the first command followed after the Poling by the FeliCa
protocol. The bit TargetActivated in the Status2Reg register is set to logic 1.
19.3.1.10 MFAuthent
This command manages MIFARE authentication to enable a secure communication to
any MIFARE Mini, MIFARE 1K and MIFARE 4K card. The following data is written to the
FIFO buffer before the command can be activated:
• Authentication command code (60h, 61h)
• Block address
• Sector key byte 0
• Sector key byte 1
• Sector key byte 2
• Sector key byte 3
• Sector key byte 4
• Sector key byte 5
• Card serial number byte 0
• Card serial number byte 1
• Card serial number byte 2
• Card serial number byte 3
In total 12 bytes are written to the FIFO.
Remark: When the MFAuthent command is active all access to the FIFO buffer is
blocked. However, if there is access to the FIFO buffer, the ErrorReg register’s WrErr bit is
set.
This command automatically terminates when the MIFARE card is authenticated and the
Status2Reg register’s MFCrypto1On bit is set to logic 1.
This command does not terminate automatically if the card does not answer, so the timer
must be initialized to automatic mode. In this case, in addition to the IdleIRq bit, the
TimerIRq bit can be used as the termination criteria. During authentication processing, the
RxIRq bit and TxIRq bit are blocked. The Crypto1On bit is only valid after termination of
the MFAuthent command, either after processing the protocol or writing Idle to the
CommandReg register.
If an error occurs during authentication, the ErrorReg register’s ProtocolErr bit is set to
logic 1 and the Status2Reg register’s Crypto1On bit is set to logic 0.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
105 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
19.3.1.11 SoftReset
This command performs a reset of the device. The configuration data of the internal buffer
remains unchanged. All registers are set to the reset values. This command automatically
terminates when finished.
Remark: The SerialSpeedReg register is reset and therefore the serial data rate is set to
9.6 kBd.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
106 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
20. Testsignals
20.1 Selftest
The PN512 has the capability to perform a digital selftest. To start the selftest the following
procedure has to be performed:
1. Perform a soft reset.
2. Clear the internal buffer by writing 25 bytes of 00h and perform the Config Command.
3. Enable the Selftest by writing the value 09h to the register AutoTestReg.
4. Write 00h to the FIFO.
5. Start the Selftest with the CalcCRC Command.
6. The Selftest will be performed.
7. When the Selftest is finished, the FIFO contains the following bytes:
Version 1.0 has a different Selftest answer, explained in Section 21.
Correct answer for VersionReg equal to 82h:
00h, EBh, 66h, BAh, 57h, BFh, 23h, 95h, D0h, E3h, 0Dh, 3Dh, 27h, 89h, 5Ch, DEh,
9Dh, 3Bh, A7h, 00h, 21h, 5Bh, 89h, 82h, 51h, 3Ah, EBh, 02h, 0Ch, A5h, 00h,
49h, 7Ch, 84h, 4Dh, B3h, CCh, D2h, 1Bh, 81h, 5Dh, 48h, 76h, D5h, 71h, 61h,
21h, A9h, 86h, 96h, 83h, 38h, CFh, 9Dh, 5Bh, 6Dh, DCh, 15h, BAh, 3Eh, 7Dh,
95h, 3Bh, 2Fh
20.2 Testbus
The testbus is implemented for production test purposes. The following configuration can
be used to improve the design of a system using the PN512. The testbus allows to route
internal signals to the digital interface. The testbus signals are selected by accessing
TestBusSel in register TestSel2Reg.
Table 159. Testsignal routing (TestSel2Reg = 07h)
Pins
D6
D5
D4
D3
D2
D1
D0
Testsignal
sdata
scoll
svalid
sover
RCV_reset
RFon,
filtered
Envelope
Table 160. Description of Testsignals
Pins
D6
Testsignal
sdata
Description
shows the actual received data stream.
D5
scoll
shows if in the actual bit a collision has been detected (106 kbit only)
shows if sdata and scoll are valid
D4
svalid
D3
sover
shows that the receiver has detected a stop condition
(ISO/IEC 14443A/ MIFARE mode only).
D2
D1
D0
RCV_reset
shows if the receiver is reset
RFon, filtered shows the value of the internal RF level detector
Envelope shows the output of the internal coder
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
107 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 161. Testsignal routing (TestSel2Reg = 0Dh)
Pins
D6
D5
D4
D3
D2
D1
D0
Testsignal clkstable
clk27/8
clk27rf/8 clkrf13rf/4
clk27
clk27rf
clk13rf
Table 162. Description of Testsignals
Pins
D6
D5
D4
D3
D2
D1
D0
Testsignal
clkstable
clk27/8
clk27rf/8
clkrf13/4
clk27
Description
shows if the oscillator delivers a stable signal.
shows the output signal of the oscillator divided by 8
shows the clk27rf signal divided by 8
shows the clk13rf divided by 4.
shows the output signal of the oscillator
shows the RF clock multiplied by 2.
shows the RF clock of 13.56 MHz
clk27rf
clk13rf
Table 163. Testsignal routing (TestSel2Reg = 19h)
Pins
D6
D5
D4
D3
D2
D1
D0
Testsignal
-
TRunning
-
-
-
-
-
Table 164. Description of Testsignals
Pins
D6
D5
D4
D3
D2
D1
D0
Testsignal
Description
-
-
TRunning
TRunning stops 1 clockcycle after TimerIRQ is raised
-
-
-
-
-
-
-
-
-
-
20.3 Testsignals at pin AUX
Table 165. Testsignals description
SelAux
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
Description for Aux1 / Aux2
Tristate
DAC: register TestDAC 1/2
DAC: testsignal corr1
DAC: testsignal corr2
DAC: testsignal MinLevel
DAC: ADC_I
DAC: ADC_Q
DAC: testsignal ADC_I combined with ADC_Q
Testsignal for production test
SAM clock
High
low
TxActive
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
108 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 165. Testsignals description
SelAux
1101
Description for Aux1 / Aux2
RxActive
1110
Subcarrier detected
TstBusBit
1111
Each signal can be switched to pin AUX1 or AUX2 by setting SelAux1 or SelAux2 in the
register AnalogTestReg.
Note: The DAC has a current output, it is recommended to use a 1 k pull-down
resistance at pins AUX1/AUX2.
20.4 PRBS
Enables the PRBS9 or PRBS15 sequence according to ITU-TO150. To start the
transmission of the defined datastream the command send has to be activated. The
preamble/Sync byte/start bit/parity bit are generated automatically depending on the
selected mode.
Note: All relevant register to transmit data have to be configured before entering PRBS
mode according ITU-TO150.
21. Errata sheet
This data sheet is describing the functionality for version 2.0 and the industrial version.
This chapter lists all differences from version 1.0 to version 2.0:
The value of the version in Section 9.2.4.8 is set to80h.
The behaviour ‘RFU’ for the register is undefined.
The answer to the Selftest (see Section 20.1) for version 1.0 (VersionReg equal to 80h):
00h, AAh, E3h, 29h, 0Ch, 10h, 29zhh, 6Bh,
76h, 8Dh, AFh, 4Bh, A2h, DAh, 76h, 99h
C7h, 5Eh, 24h, 69h, D2h, BAh, FAh, BCh
3Eh, DAh, 96h, B5h, F5h, 94h, B0h, 3Ah
4Eh, C3h, 9Dh, 94h, 76h, 4Ch, EAh, 5Eh
38h, 10h, 8Fh, 2Dh, 21h, 4Bh, 52h, BFh
4Eh, C3h, 9Dh, 94h, 76h, 4Ch, EAh, 5Eh
38h, 10h, 8Fh, 2Dh, 21h, 4Bh, 52h, BFh
FBh, F4h, 19h, 94h, 82h, 5Ah, 72h, 9Dh
BAh, 0Dh, 1Fh, 17h, 56h, 22h, B9h, 08h
Only the default setting for the prescaler (see Section 15 “Timer unit” on page 96): t =
((TPreScaler*2+1)*TReload+1)/13,56 MHz is supported. As such only the formula fTimer
13,56 MHz/(2*PreScaler+1) is applicable for the TPrescalerHigh in Table 100 “Description
of TModeReg bits” on page 57 and TPrescalerLo in Table 101 “TPrescalerReg register
(address 2Bh); reset value: 00h, 00000000b” on page 58. As there is no option for the
prescaler available, also the TPrescalEven is not available Section 9.2.2.10 on page 45.
This bit is set to ‘RFU’.
=
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
109 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Especially when using time slot protocols, it is needed that the error flag is copied into the
status information of the frame. When using the RxMultiple feature (see Section 9.2.2.4
on page 39) within version 1.0 the protocol error flag is not included in the status
information for the frame. In addition the CRCOk is copied instead of the CRCErr. This
can be a problem in frames without length information e.g. ISO/IEC 14443-B.
The version 1.0 does not accept a Type B EOF if there is no 1 bit after the series of 0 bits,
as such the configuration within Section 9.2.2.15 “TypeBReg” on page 50 bit 4 for
RxEOFReq does not exist. In addition the IC only has the possibility to select the
minimum or maximum timings for SOF/EOF generation defined in ISO/IEC14443B. As
such the configuration possible in version 2.0 through the EOFSOFAdjust bit (see Section
9.2.4.7 “AutoTestReg” on page 64) does not exist and the configuration is limited to only
setting minimum and maximum length according ISO/IEC 14443-B, see Section 9.2.2.15
“TypeBReg” on page 50, bit 4.
22. Application design-in information
The figure below shows a typical circuit diagram, using a complementary antenna
connection to the PN512.
The antenna tuning and RF part matching is described in the application note “NFC
Transmission Module Antenna and RF Design Guide”.
supply
DVDD
AVDD
TVDD
RX
C
RX
DVDD
PVDD
SVDD
R
1
R
2
VMID
C
vmid
NRSTPD
interface
C
1
R
Q
L
0
TX1
PN512
antenna
Lant
HOST
CONTROLLER
C
C
C
C
0
2
TVSS
IRQ
0
2
C
1
R
Q
L
0
TX2
AVSS
DVSS
OSCIN
OSCOUT
27.12 MHz
001aan232
Fig 38. Typical circuit diagram
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
110 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
23. Limiting values
Table 166. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
VDDA
Parameter
Conditions
Min
Max
+4.0
+4.0
+4.0
+4.0
+4.0
Unit
V
analog supply voltage
digital supply voltage
0.5
0.5
0.5
0.5
0.5
VDDD
V
VDD(PVDD) PVDD supply voltage
VDD(TVDD) TVDD supply voltage
VDD(SVDD) SVDD supply voltage
V
V
V
VI
input voltage
all input pins except pins SIGIN and
RX
VSS(PVSS) 0.5 VDD(PVDD) + 0.5
V
pin MFIN
VSS(PVSS) 0.5 VDD(SVDD) + 0.5
V
Ptot
total power dissipation
junction temperature
per package; and VDDD in shortcut
mode
-
200
mW
Tj
-
-
125
C
VESD
electrostatic discharge
voltage
HBM; 1500 , 100 pF;
JESD22-A114-B
2000
V
MM; 0.75 H, 200 pF;
-
200
V
JESD22-A114-A
Charged device model;
JESD22-C101-A
on all pins
-
-
200
500
V
V
on all pins except SVDD in
TFBGA64 package
Industrial version:
VESD electrostatic discharge
voltage
HBM; 1500 , 100 pF;
JESD22-A114-B
-
-
2000
200
V
V
MM; 0.75 H, 200 pF;
JESD22-A114-A
Charged device model;
AEC-Q100-011
on all pins
-
-
200
500
V
V
on all pins except SVDD
24. Recommended operating conditions
Table 167. Operating conditions
Symbol
Parameter
Conditions
Min
Typ
Max Unit
[1][2]
[1][2]
[1][2]
VDDA
analog supply voltage
VDD(PVDD) VDDA = VDDD = VDD(TVDD)
;
2.5
-
-
-
3.6
3.6
3.6
V
V
V
VSSA = VSSD = VSS(PVSS) = VSS(TVSS) = 0 V
VDD(PVDD) VDDA = VDDD = VDD(TVDD)
VSSA = VSSD = VSS(PVSS) = VSS(TVSS) = 0 V
VDD(PVDD) VDDA = VDDD = VDD(TVDD)
digital supply voltage
;
2.5
2.5
VDDD
VDD(TVDD) TVDD supply voltage
;
VSSA = VSSD = VSS(PVSS) = VSS(TVSS) = 0 V
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
111 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 167. Operating conditions …continued
Symbol
Parameter
Conditions
Min
Typ
Max Unit
[3]
VDD(PVDD) PVDD supply voltage
VDD(PVDD) VDDA = VDDD = VDD(TVDD)
;
1.6
-
3.6
V
VSSA = VSSD = VSS(PVSS) = VSS(TVSS) = 0 V
VSSA = VSSD = VSS(PVSS) = VSS(TVSS) = 0 V
HVQFN32, HVQFN40, TFBGA64
VDD(SVDD) SVDD supply voltage
1.6
-
-
3.6
V
Tamb
Industrial version:
Tamb ambient temperature
ambient temperature
30
+85
C
HVQFN32
40
-
+90
C
[1] Supply voltages below 3 V reduce the performance (the achievable operating distance).
[2] VDDA, VDDD and VDD(TVDD) must always be the same voltage.
[3] VDD(PVDD) must always be the same or lower voltage than VDDD
25. Thermal characteristics
Table 168. Thermal characteristics
.
Symbol
Parameter
Conditions
Package
HVQFN32
HVQFN40
TFBGA64
Typ
Unit
K/W
K/W
K/W
Rthj-a
Thermal resistance from
junction to ambient
In still air with exposed pad
soldered on a 4 layer Jedec PCB
In still air
40
35
<tbd>
26. Characteristics
Table 169. Characteristics
Symbol Parameter
Input characteristics
Conditions
Min
Typ
Max
Unit
Pins A0, A1 and NRSTPD
ILI
input leakage current
HIGH-level input voltage
LOW-level input voltage
1
-
-
-
+1
A
V
VIH
0.7VDD(PVDD)
-
-
VIL
0.3VDD(PVDD)
V
Pin SIGIN
ILI
input leakage current
HIGH-level input voltage
LOW-level input voltage
1
-
-
-
+1
A
V
VIH
0.7VDD(SVDD)
-
-
VIL
0.3VDD(SVDD)
V
Pin ALE
ILI
input leakage current
HIGH-level input voltage
LOW-level input voltage
1
-
-
-
+1
A
V
VIH
0.7VDD(PVDD)
-
-
VIL
0.3VDD(PVDD)
V
Pin RX[1]
Vi
input voltage
1
-
VDDA +1
-
V
Ci
input capacitance
VDDA = 3 V; receiver active;
VRX(p-p) = 1 V; 1.5 V (DC)
offset
-
10
pF
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
112 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 169. Characteristics …continued
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Ri
input resistance
VDDA = 3 V; receiver active;
VRX(p-p) = 1 V; 1.5 V (DC)
offset
-
350
-
Input voltage range; see Figure 39
Vi(p-p)(min) minimum peak-to-peak input Manchester encoded;
voltage DDA = 3 V
Vi(p-p)(max) maximum peak-to-peak input Manchester encoded;
-
-
100
4
-
-
mV
V
V
voltage
VDDA = 3 V
Input sensitivity; see Figure 39
Vmod
modulation voltage
minimum Manchester
encoded; VDDA = 3 V;
RxGain[2:0] = 111b (48 dB)
-
5
-
mV
Pin OSCIN
ILI
input leakage current
HIGH-level input voltage
LOW-level input voltage
input capacitance
1
-
+1
A
V
VIH
VIL
Ci
0.7VDDA
-
-
-
-
-
0.3VDDA
-
V
VDDA = 2.8 V; DC = 0.65 V;
AC = 1 V (p-p)
2
pF
Input/output characteristics
pins D1, D2, D3, D4, D5, D6 and D7
ILI
input leakage current
1
-
-
-
-
+1
A
V
VIH
VIL
VOH
HIGH-level input voltage
LOW-level input voltage
HIGH-level output voltage
0.7VDD(PVDD)
-
-
0.3VDD(PVDD)
VDD(PVDD)
V
VDD(PVDD) = 3 V; IO = 4 mA
VDD(PVDD) = 3 V; IO = 4 mA
VDD(PVDD)
0.4
V
VOL
LOW-level output voltage
VSS(PVSS)
-
VSS(PVSS)
0.4
+
V
IOH
IOL
HIGH-level output current
LOW-level output current
VDD(PVDD) = 3 V
VDD(PVDD) = 3 V
-
-
-
-
4
4
mA
mA
Output characteristics
Pin SIGOUT
VOH
HIGH-level output voltage
VDD(SVDD) = 3 V; IO = 4 mA
VDD(SVDD) = 3 V; IO = 4 mA
VDD(SVDD)
0.4
-
-
VDD(SVDD)
V
V
VOL
LOW-level output voltage
VSS(PVSS)
VSS(PVSS)
0.4
+
IOL
LOW-level output current
HIGH-level output current
VDD(SVDD) = 3 V
VDD(SVDD) = 3 V
-
-
-
-
4
4
mA
mA
IOH
Pin IRQ
VOH
HIGH-level output voltage
LOW-level output voltage
VDD(PVDD) = 3 V; IO = 4 mA
VDD(PVDD) = 3 V; IO = 4 mA
VDD(PVDD)
0.4
-
-
VDD(PVDD)
V
V
VOL
VSS(PVSS)
VSS(PVSS)
0.4
+
IOL
IOH
LOW-level output current
HIGH-level output current
VDD(PVDD) = 3 V
VDD(PVDD) = 3 V
-
-
-
-
4
4
mA
mA
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
113 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 169. Characteristics …continued
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Pins AUX1 and AUX2
VOH
VOL
HIGH-level output voltage
LOW-level output voltage
VDDD = 3 V; IO = 4 mA
VDDD = 3 V; IO = 4 mA
VDDD 0.4
-
-
VDDD
V
V
VSS(PVSS)
VSS(PVSS)
0.4
+
IOL
IOH
LOW-level output current
HIGH-level output current
VDDD = 3 V
VDDD = 3 V
-
-
-
-
4
4
mA
mA
Pins TX1 and TX2
VOL LOW-level output voltage
VDD(TVDD) = 3 V;
-
-
-
-
-
-
-
-
-
-
-
-
0.15
V
V
V
V
V
V
V
V
I
DD(TVDD) = 32 mA;
CWGsP[5:0] = 0Fh
VDD(TVDD) = 3 V;
IDD(TVDD) = 80 mA;
CWGsP[5:0] = 0Fh
0.4
VDD(TVDD) = 2.5 V;
0.24
IDD(TVDD) = 32 mA;
CWGsP[5:0] = 0Fh
VDD(TVDD) = 2.5 V;
0.64
IDD(TVDD) = 80 mA;
CWGsP[5:0] = 0Fh
VOH
HIGH-level output voltage
VDD(TVDD) = 3 V;
IDD(TVDD) = 32 mA;
CWGsP[5:0] = 3Fh
VDD(TVDD)
0.15
-
-
-
-
V
DD(TVDD) = 3 V;
VDD(TVDD)
0.4
IDD(TVDD) = 80 mA;
CWGsP[5:0] = 3Fh
V
DD(TVDD) = 2.5 V;
VDD(TVDD)
0.24
IDD(TVDD) = 32 mA;
CWGsP[5:0] = 3Fh
V
DD(TVDD) = 2.5 V;
VDD(TVDD)
0.64
IDD(TVDD) = 80 mA;
CWGsP[5:0] = 3Fh
Industrial version:
VOL LOW-level output voltage
VDD(TVDD) = 2.5 V;
IDD(TVDD) = 32 mA;
CWGsP[5:0] = 3Fh
-
-
-
-
-
-
0.18
V
V
V
V
VDD(TVDD) = 2.5 V;
0.44
I
DD(TVDD) = 80 mA;
CWGsP[5:0] = 3Fh
VOH
HIGH-level output voltage
VDD(TVDD) = 3 V;
IDD(TVDD) = 32 mA;
CWGsP[5:0] = 3Fh
VDD(TVDD)
0.18
-
-
VDD(TVDD) = 3 V;
IDD(TVDD) = 80 mA;
CWGsP[5:0] = 3Fh
VDD(TVDD)
0.44
Output resistance for TX1/TX2,
Industrial Version:
ROP,01H
High level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsP = 01h
-
123
180
261
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
114 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 169. Characteristics …continued
Symbol Parameter
Conditions
Min
Typ
Max
Unit
ROP,02H
ROP,04H
ROP,08H
ROP,10H
ROP,20H
ROP,3FH
RON,10H
RON,20H
RON,40H
RON,80H
RON,F0H
High level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsP = 02h
-
-
-
-
-
-
-
-
-
-
-
61
90
131
High level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsP = 04h
30
15
7.5
4.2
2
46
23
12
6
68
35
19
9
High level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsP = 08h
High level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsP = 10h
High level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsP = 20h
High level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsP = 3Fh
3
5
Low level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsN = 10h
30
15
7.5
4.2
2
46
23
12
6
68
35
19
9
Low level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsN = 20h
Low level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsN = 40h
Low level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsN = 80h
Low level output resistance TVDD = 3 V, VTX = TVDD
100 mV, CWGsN = F0h
3
5
Current consumption
Ipd
power-down current
VDDA = VDDD = VDD(TVDD) =
VDD(PVDD) = 3 V
[2]
[2]
hard power-down; pin
NRSTPD set LOW
-
-
-
-
5
A
A
soft power-down; RF
level detector on
10
[3]
[4][5][6]
[7]
IDD(PVDD) PVDD supply current
IDD(TVDD) TVDD supply current
IDD(SVDD) SVDD supply current
pin PVDD
-
-
-
-
-
-
40
100
4
mA
mA
mA
mA
mA
pin TVDD; continuous wave
pin SVDD
60
-
IDDD
IDDA
digital supply current
analog supply current
pin DVDD; VDDD = 3 V
6.5
7
9
pin AVDD; VDDA = 3 V,
CommandReg register’s
RcvOff bit = 0
10
pin AVDD; receiver
switched off; VDDA = 3 V,
CommandReg register’s
RcvOff bit = 1
-
-
3
5
mA
mA
Industrial version:
IDDD
digital supply current
pin DVDD; VDDD = 3 V
6.5
9,5
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
115 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 169. Characteristics …continued
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Ipd
power-down current
VDDA = VDDD = VDD(TVDD)
VDD(PVDD) = 3 V
=
[2]
[2]
hard power-down; pin
NRSTPD set LOW
-
-
-
-
15
30
A
A
soft power-down; RF
level detector on
Clock frequency
fclk
clk
tjit
clock frequency
-
27.12
-
MHz
%
clock duty cycle
jitter time
40
-
50
-
60
10
RMS
ps
Crystal oscillator
VOH
VOL
Ci
HIGH-level output voltage
pin OSCOUT
pin OSCOUT
pin OSCOUT
pin OSCIN
-
-
-
-
1.1
0.2
2
-
-
-
-
V
LOW-level output voltage
input capacitance
V
pF
pF
2
Typical input requirements
fxtal
crystal frequency
-
-
-
-
27.12
-
-
MHz
ESR
CL
equivalent series resistance
load capacitance
100
-
10
pF
Pxtal
crystal power dissipation
50
100
W
[1] The voltage on pin RX is clamped by internal diodes to pins AVSS and AVDD.
[2] pd is the total current for all supplies.
[3] IDD(PVDD) depends on the overall load at the digital pins.
I
[4] IDD(TVDD) depends on VDD(TVDD) and the external circuit connected to pins TX1 and TX2.
[5] During typical circuit operation, the overall current is below 100 mA.
[6] Typical value using a complementary driver configuration and an antenna matched to 40 between pins TX1 and TX2 at 13.56 MHz.
[7]
IDD(SVDD) depends on the load at pin MFOUT.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
116 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
V
mod
V
V
i(p-p)(min)
i(p-p)(max)
VMID
13.56 MHz
carrier
0 V
001aak012
Fig 39. Pin RX input voltage range
26.1 Timing characteristics
Table 170. SPI timing characteristics
Symbol
tWL
Parameter
Conditions
line SCK
Min
Typ
Max
Unit
ns
pulse width LOW
pulse width HIGH
50
50
25
-
-
-
-
-
-
tWH
line SCK
ns
th(SCKH-D)
SCK HIGH to data input SCK to changing
hold time MOSI
ns
tsu(D-SCKH) data input to SCK HIGH changing MOSI to
set-up time SCK
25
-
-
-
-
-
ns
ns
ns
th(SCKL-Q)
SCK LOW to data output SCK to changing
hold time MISO
25
-
t(SCKL-NSSH) SCK LOW to NSS HIGH
time
0
Table 171. I2C-bus timing in Fast mode
Symbol Parameter
Conditions
Fast mode High-speed Unit
mode
Min Max Min Max
fSCL
SCL clock frequency
0
400
-
0
3400 kHz
tHD;STA
hold time (repeated) START
condition
after this period,
the first clock pulse
is generated
600
160
-
ns
tSU;STA
set-up time for a repeated
START condition
600
-
160
-
ns
tSU;STO set-up time for STOP condition
600
1300
600
0
-
160
160
60
-
ns
ns
ns
ns
tLOW
tHIGH
LOW period of the SCL clock
HIGH period of the SCL clock
-
-
-
-
tHD;DAT data hold time
900
0
70
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
117 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 171. I2C-bus timing in Fast mode …continued
Symbol Parameter
Conditions
Fast mode High-speed Unit
mode
Min Max Min Max
tSU;DAT
data set-up time
100
20
-
10
-
ns
ns
ns
ns
tr
tf
tr
rise time
fall time
rise time
SCL signal
SCL signal
300 10
300 10
300 10
40
40
80
20
SDA and SCL
signals
20
tf
fall time
SDA and SCL
signals
20
300 10
80
-
ns
tBUF
bus free time between a STOP
and START condition
1.3
-
1.3
s
t
t
t
t
SCKL
SCKL
SCKH
SHDX
SCK
t
SLDX
t
t
DXSH
DXSH
MOSI
MISO
NSS
MSB
MSB
LSB
LSB
t
SLNH
001aaj634
Remark: The signal NSS must be LOW to be able to send several bytes in one data stream.
To send more than one data stream NSS must be set HIGH between the data streams.
Fig 40. Timing diagram for SPI
SDA
t
t
t
t
r
f
SU;DAT
SP
t
t
t
t
BUF
LOW
f
HD;STA
SCL
t
t
t
SU;STO
r
HIGH
t
t
SU;STA
HD;STA
t
HD;DAT
S
Sr
P
S
001aaj635
Fig 41. Timing for Fast and Standard mode devices on the I2C-bus
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
118 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
26.2 8-bit parallel interface timing
26.2.1 AC symbols
Each timing symbol has five characters. The first character is always 't' for time. The other
characters indicate the name of a signal or the logic state of that signal (depending on
position):
Table 172. AC symbols
Designation
Signal
Designation
Logic Level
HIGH
A
D
W
R
L
address
H
L
data
LOW
NWR or nWait
Z
X
V
N
high impedance
any level or data
any valid signal or data
NSS
NRD or R/NW or nWrite
ALE or AS
C
S
NCS
NDS or nDStrb and nAStrb, SCK
Example: tAVLL = time for address valid to ALE low
26.2.2 AC operating specification
26.2.2.1 Bus timing for separated Read/Write strobe
Table 173. Timing specification for separated Read/Write strobe
Symbol Parameter
Min
10
5
Max Unit
tLHLL
ALE pulse width
-
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tAVLL
Multiplexed Address Bus valid to ALE low (Address Set Up Time)
-
tLLAX
Multiplexed Address Bus valid after ALE low (Address Hold Time) 5
-
tLLWL
tCLWL
tWHCH
tRLDV
tRHDZ
tDVWH
tWHDX
tWLWH
tAVWL
tWHAX
tWHWL
ALE low to NWR, NRD low
10
-
NCS low to NRD, NWR low
0
-
NRD, NWR high to NCS high
0
-
NRD low to DATA valid
-
35
10
-
NRD high to DATA high impedance
DATA valid to NWR high
-
5
DATA hold after NWR high (Data Hold Time)
NRD, NWR pulse width
5
-
40
30
5
-
Separated Address Bus valid to NRD, NWR low (Set Up Time)
Separated Address Bus valid after NWR high (Hold Time)
period between sequenced read/write accesses
-
-
40
-
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
119 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
t
LHLL
ALE
t
WHCH
t
CLWL
NCS
t
LLWL
t
t
t
WHWL
WHWL
WLWH
NWR
NRD
t
t
t
WLDV
AVLL
LLAX
t
WHDX
t
t
RHDZ
RLDV
D0...D7
A0...A3
D0...D7
multiplexed
addressbus
A0...A3
t
WHAX
t
AVWL
SEPARATED ADDRESSBUS A0...A3
001aan233
Fig 42. Timing diagram for separated Read/Write strobe
Remark: For separated address and data bus the signal ALE is not relevant and the
multiplexed addresses on the data bus don’t care.
For the multiplexed address and data bus the address lines A0 to A3 have to be
connected as described in chapter Automatic host controller Interface Type Detection.
26.2.2.2 Bus timing for common Read/Write strobe
Table 174. Timing specification for common Read/Write strobe
Symbol
tLHLL
Parameter
Min
Max Unit
AS pulse width
10
-
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tAVLL
Multiplexed Address Bus valid to AS low (Address Set Up Time) 5
Multiplexed Address Bus valid after AS low (Address Hold Time) 5
-
tLLAX
-
tLLSL
AS low to NDS low
10
-
tCLSL
tSHCH
tSLDV,R
tSHDZ
tDVSH
tSHDX
tSHRX
tSLSH
tAVSL
NCS low to NDS low
0
0
-
NDS high to NCS high
-
NDS low to DATA valid (for read cycle)
NDS low to DATA high impedance (read cycle)
DATA valid to NDS high (for write cycle)
DATA hold after NDS high (write cycle, Hold Time)
R/NW hold after NDS high
-
35
10
-
-
5
5
-
5
-
NDS pulse width
40
30
5
-
Separated Address Bus valid to NDS low (Hold Time)
Separated Address Bus valid after NDS high (Set Up Time)
-
tSHAX
-
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
120 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
t
LHLL
ALE
t
SHCH
t
CLSL
NCS
t
t
RVSL
SHRX
R/NW
t
LLSL
t
t
t
SHSL
SHSL
SLSH
NDS
t
SLDV, R
t
t
SLDV, W
LLAX
t
t
SHDX
SHDZ
t
AVLL
D0...D7
D0...D7
multiplexed
addressbus
A0...A3
t
SHAX
t
AVSL
SEPARATED ADDRESSBUS A0...A3
A0...A3
001aan234
Fig 43. Timing diagram for common Read/Write strobe
Remark: For separated address and data bus the signal ALE is not relevant and the
multiplexed addresses on the data bus don’t care. For the multiplexed address and data
bus the address lines A0 to A3 have to be connected as described in Automatic
-Controller Interface Type Detection.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
121 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
27. Package information
The PN512 can be delivered in 3 different packages.
Table 175. Package information
Package
HVQFN32
HVQFN40
TFBGA64
Remarks
8-bit parallel interface not supported
Supports the 8-bit parallel interface
Ball grid array facilitating development of an PCI compliant device
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
122 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
28. Package outline
HVQFN32: plastic thermal enhanced very thin quad flat package; no leads;
32 terminals; body 5 x 5 x 0.85 mm
SOT617-1
B
A
D
terminal 1
index area
A
A
1
E
c
detail X
C
e
1
y
y
e
1/2 e
v
M
M
b
C
C
A B
C
1
w
9
16
L
17
8
e
e
E
h
2
1/2 e
1
24
terminal 1
index area
32
25
X
D
h
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
(1)
A
(1)
(1)
UNIT
A
b
c
E
e
e
e
2
y
D
D
E
L
v
w
y
1
1
h
1
h
max.
0.05 0.30
0.00 0.18
5.1
4.9
3.25
2.95
5.1
4.9
3.25
2.95
0.5
0.3
mm
0.05 0.1
1
0.2
0.5
3.5
3.5
0.1
0.05
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
01-08-08
02-10-18
SOT617-1
- - -
MO-220
- - -
Fig 44. Package outline package version (HVQFN32)
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
123 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
HVQFN40: plastic thermal enhanced very thin quad flat package; no leads;
40 terminals; body 6 x 6 x 0.85 mm
SOT618-1
D
B
A
terminal 1
index area
A
A
1
E
c
detail X
e
1
C
v
C
C
A
B
e
b
1/2 e
y
1
y
C
w
11
20
L
21
10
e
E
e
2
h
1/2 e
1
30
terminal 1
index area
40
31
X
D
h
0
2.5
5 mm
v
scale
Dimensions (mm are the original dimensions)
(1)
(1)
(1)
E
Unit
A
A
1
b
c
D
D
h
E
e
e
e
2
L
w
y
y
1
h
1
max 1.00 0.05 0.30 0.2 6.1 4.25 6.1 4.25 0.5 4.5 4.5 0.5 0.1 0.05 0.05 0.1
mm nom 0.85 0.02 0.21
0.80 0.00 0.18
6.0 4.10 6.0 4.10
5.9 3.95 5.9 3.95
0.4
0.3
min
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
sot618-1_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
02-10-22
13-11-05
SOT618-1
MO-220
Fig 45. Package outline package version (HVQFN40)
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
124 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
TFBGA64: plastic thin fine-pitch ball grid array package; 64 balls
SOT1336-1
D
B
A
ball A1
index area
A
2
A
E
A
1
detail X
e
1
C
1/2 e
Ø v
Ø w
C
C
A
B
y
1
y
e
b
C
H
G
F
e
E
D
C
B
A
e
2
1/2 e
1
2
3
4
5
6
7
8
ball A1
index area
X
0
5 mm
scale
v
Dimensions (mm are the original dimensions)
Unit
A
A
1
A
2
b
D
E
e
e
1
e
2
w
y
y
1
max 1.15 0.35 0.80 0.45 5.6 5.6
mm nom 1.00 0.30 0.70 0.40 5.5 5.5 0.65 4.55 4.55 0.15 0.08 0.1 0.1
0.90 0.25 0.65 0.35 5.4 5.4
min
sot1336-1_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
- - -
JEITA
12-06-19
12-08-28
SOT1336-1
Fig 46. Package outline package version (TFBGA64)
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
125 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
29. Abbreviations
Table 176. Abbreviations
Acronym
ADC
ASK
BPSK
CRC
CW
Description
Analog-to-Digital Converter
Amplitude Shift keying
Binary Phase Shift Keying
Cyclic Redundancy Check
Continuous Wave
DAC
EOF
HBM
I2C
Digital-to-Analog Converter
End of frame
Human Body Model
Inter-integrated Circuit
Least Significant Bit
Master In Slave Out
Machine Model
LSB
MISO
MM
MOSI
MSB
NSS
PCB
PLL
Master Out Slave In
Most Significant Bit
Not Slave Select
Printed-Circuit Board
Phase-Locked Loop
Pseudo-Random Bit Sequence
Receiver
PRBS
RX
SOF
SPI
Start Of Frame
Serial Peripheral Interface
Transmitter
TX
UART
Universal Asynchronous Receiver Transmitter
30. Glossary
Modulation index — Defined as the voltage ratio (Vmax Vmin) / (Vmax + Vmin).
Load modulation index — Defined as the voltage ratio for the card
(Vmax Vmin) / (Vmax + Vmin) measured at the card’s coil.
Initiator — Generates RF field at 13.56 MHz and starts the NFCIP-1 communication.
Target — Responds to command either using load modulation scheme (RF field
generated by Initiator) or using modulation of self generated RF field (no RF field
generated by initiator).
31. References
[1] Application note — NFC Transmission Module Antenna and RF Design Guide
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
126 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
32. Revision history
Table 177. Revision history
Document ID
PN512 v.4.5
Modifications:
PN512 v.4.4
Modifications:
Release date
Data sheet status
Change notice
Supersedes
20131217
Product data sheet
-
PN512 v.4.4
• Typo corrected
20130730
Product data sheet
-
PN512 v.4.3
PN512 v.4.2
• Value added in Table 166 “Limiting values”
• Change of descriptive title
PN512 v.4.3
20130507
Product data sheet
-
Modifications:
• New type PN5120A0ET/C2 added
• Table 72 “Description of MifNFCReg bits”: description of TxWait updated
• Table 153 “Register and bit settings controlling the signal on pin TX1” and Table 153 “Register
and bit settings controlling the signal on pin TX1”: updated
• Table 166 “Limiting values”: VESD values added
PN512 v.4.2
20120828
Product data sheet
-
PN512 v.4.1
Modifications:
• Table 123 “AutoTestReg register (address 36h); reset value: 40h, 01000000b”: description of
bits 4 and 5 corrected
PN512 v.4.1
Modifications:
PN512 v.4.0
Modifications:
PN512 v.3.9
Modifications:
20120821
Product data sheet
-
PN512 v.4.0
PN512 v.3.9
PN512 v.3.8
• Table 124 “Description of bits”: description of bits 4 and 5 corrected
20120712
• Section 33.4 “Licenses”: updated
20120201 Product data sheet
Product data sheet
-
-
• Adding information on the different version in General description.
• Adding Section 21 “Errata sheet” on page 109 for explanation of differences between 1.0 and
2.0.
• Adding ordering information for version 1.0 and industrial version in Table 2 “Ordering
information” on page 5
• Adding the limitations and characteristics for the industrial version, see Table 1 “Quick
reference data” on page 4, Table 166 “Limiting values” on page 111, Table 1 “Quick reference
data” on page 4
• Referring to the Section 21 “Errata sheet” on page 109 within the following sections: Section
9.2.2.4 “RxModeReg” on page 39, Section 9.2.2.10 “DemodReg” on page 45, Section 9.2.2.15
“TypeBReg” on page 50, Section 9.2.3.10 “TMode Register, TPrescaler Register” on page 57,
Section 9.2.4.7 “AutoTestReg” on page 64, Section 9.2.4.8 “VersionReg” on page 64, Section
9.1.1 “Register bit behavior” on page 23, Section 15 “Timer unit” on page 96, Section 20
“Testsignals” on page 107;
• Update of command ‘Mem’ to ‘Configure’ and ‘RFU’ to ‘Autocoll’ in Table 158 “Command
overview” on page 101.
• Change of ‘Mem’ to ‘Configure’ in ‘Mem’ in Section 19.3.1.2 “Config command” on page 101
• Adding Autocoll in Section 19.3.1.9 “AutoColl” on page 103
PN512 v.3.8
Modifications:
111310
20111025
Product data sheet
-
PN512 v.3.7
• Table 168 “Characteristics”: unit of Pxtal corrected
June 2005
Objective data sheet
-
Modifications:
• Initial version
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
127 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
33. Legal information
33.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
Suitability for use — NXP Semiconductors products are not designed,
33.2 Definitions
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
33.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
128 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
33.4 Licenses
Purchase of NXP ICs with ISO/IEC 14443 type B functionality
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
This NXP Semiconductors IC is ISO/IEC 14443 Type B
software enabled and is licensed under Innovatron’s
Contactless Card patents license for ISO/IEC 14443 B.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
The license includes the right to use the IC in systems
and/or end-user equipment.
RATP/Innovatron
Technology
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
Purchase of NXP ICs with NFC technology
Purchase of an NXP Semiconductors IC that complies with one of the Near
Field Communication (NFC) standards ISO/IEC 18092 and ISO/IEC 21481
does not convey an implied license under any patent right infringed by
implementation of any of those standards.
33.5 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
MIFARE — is a trademark of NXP B.V.
34. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
129 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
35. Tables
Table 1. Quick reference data . . . . . . . . . . . . . . . . . . . . .4
Table 2. Ordering information . . . . . . . . . . . . . . . . . . . . .5
Table 3. Pin description HVQFN32 . . . . . . . . . . . . . . . .10
Table 4. Pin description HVQFN40 . . . . . . . . . . . . . . . .11
Table 5. Pin description TFBGA64. . . . . . . . . . . . . . . . .12
Table 6. Communication overview for
Table 40. Description of WaterLevelReg bits. . . . . . . . . . 33
Table 41. ControlReg register (address 0Ch); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 33
Table 42. Description of ControlReg bits . . . . . . . . . . . . 33
Table 43. BitFramingReg register (address 0Dh); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 34
Table 44. Description of BitFramingReg bits . . . . . . . . . . 34
Table 45. CollReg register (address 0Eh); reset
ISO/IEC 14443 A/MIFARE reader/writer . . . . .14
Table 7. Communication overview for FeliCa
reader/writer . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Table 8. FeliCa framing and coding . . . . . . . . . . . . . . . .16
Table 9. Start value for the CRC Polynomial: (00h),
(00h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Table 10. Communication overview for Active
value: XXh, 101XXXXXb . . . . . . . . . . . . . . . . . 35
Table 46. Description of CollReg bits. . . . . . . . . . . . . . . . 35
Table 47. PageReg register (address 10h); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 36
Table 48. Description of PageReg bits . . . . . . . . . . . . . . 36
Table 49. ModeReg register (address 11h); reset value:
3Bh, 00111011b . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 50. Description of ModeReg bits . . . . . . . . . . . . . . 37
Table 51. TxModeReg register (address 12h); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 38
Table 52. Description of TxModeReg bits . . . . . . . . . . . . 38
Table 53. RxModeReg register (address 13h); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 39
Table 54. Description of RxModeReg bits . . . . . . . . . . . . 39
Table 55. TxControlReg register (address 14h); reset
value: 80h, 10000000b . . . . . . . . . . . . . . . . . . 40
Table 56. Description of TxControlReg bits . . . . . . . . . . . 40
Table 57. TxAutoReg register (address 15h); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 41
Table 58. Description of TxAutoReg bits . . . . . . . . . . . . . 41
Table 59. TxSelReg register (address 16h); reset value:
10h, 00010000b. . . . . . . . . . . . . . . . . . . . . . . . 42
Table 60. Description of TxSelReg bits . . . . . . . . . . . . . . 42
Table 61. RxSelReg register (address 17h); reset value:
84h, 10000100b. . . . . . . . . . . . . . . . . . . . . . . . 44
Table 62. Description of RxSelReg bits . . . . . . . . . . . . . . 44
Table 63. RxThresholdReg register (address 18h);
reset value: 84h, 10000100b . . . . . . . . . . . . . . 44
Table 64. Description of RxThresholdReg bits . . . . . . . . 44
Table 65. DemodReg register (address 19h); reset
value: 4Dh, 01001101b . . . . . . . . . . . . . . . . . . 45
Table 66. Description of DemodReg bits . . . . . . . . . . . . . 45
Table 67. FelNFC1Reg register (address 1Ah); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 46
Table 68. Description of FelNFC1Reg bits . . . . . . . . . . . 46
Table 69. FelNFC2Reg register (address1Bh); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 47
Table 70. Description of FelNFC2Reg bits . . . . . . . . . . . 47
Table 71. MifNFCReg register (address 1Ch); reset
value: 62h, 01100010b. . . . . . . . . . . . . . . . . . . 48
Table 72. Description of MifNFCReg bits. . . . . . . . . . . . . 48
Table 73. ManualRCVReg register (address 1Dh);
reset value: 00h, 00000000b . . . . . . . . . . . . . . 49
Table 74. Description of ManualRCVReg bits . . . . . . . . . 49
Table 75. TypeBReg register (address 1Eh); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 50
Table 76. Description of TypeBReg bits. . . . . . . . . . . . . . 50
Table 77. SerialSpeedReg register (address 1Fh);
communication mode . . . . . . . . . . . . . . . . . . . .18
Table 11. Communication overview for Passive
communication mode . . . . . . . . . . . . . . . . . . . .19
Table 12. Framing and coding overview. . . . . . . . . . . . . .20
Table 13. MIFARE Card operation mode . . . . . . . . . . . . .20
Table 14. FeliCa Card operation mode . . . . . . . . . . . . . .21
Table 15. PN512 registers overview . . . . . . . . . . . . . . . .21
Table 16. Behavior of register bits and its designation. . .23
Table 17. PageReg register (address 00h); reset value:
00h, 0000000b . . . . . . . . . . . . . . . . . . . . . . . . .24
Table 18. Description of PageReg bits . . . . . . . . . . . . . . .24
Table 19. CommandReg register (address 01h); reset
value: 20h, 00100000b. . . . . . . . . . . . . . . . . . .24
Table 20. Description of CommandReg bits. . . . . . . . . . .24
Table 21. CommIEnReg register (address 02h); reset
value: 80h, 10000000b. . . . . . . . . . . . . . . . . . .25
Table 22. Description of CommIEnReg bits . . . . . . . . . . .25
Table 23. DivIEnReg register (address 03h); reset value:
00h, 00000000b . . . . . . . . . . . . . . . . . . . . . . . .26
Table 24. Description of DivIEnReg bits. . . . . . . . . . . . . .26
Table 25. CommIRqReg register (address 04h); reset
value: 14h, 00010100b. . . . . . . . . . . . . . . . . . .27
Table 26. Description of CommIRqReg bits . . . . . . . . . . .27
Table 27. DivIRqReg register (address 05h); reset
value: XXh, 000X00XXb. . . . . . . . . . . . . . . . . .28
Table 28. Description of DivIRqReg bits . . . . . . . . . . . . .28
Table 29. ErrorReg register (address 06h); reset value:
00h, 00000000b . . . . . . . . . . . . . . . . . . . . . . . .29
Table 30. Description of ErrorReg bits . . . . . . . . . . . . . . .29
Table 31. Status1Reg register (address 07h); reset
value: XXh, X100X01Xb. . . . . . . . . . . . . . . . . .30
Table 32. Description of Status1Reg bits . . . . . . . . . . . . .30
Table 33. Status2Reg register (address 08h); reset
value: 00h, 00000000b. . . . . . . . . . . . . . . . . . .31
Table 34. Description of Status2Reg bits . . . . . . . . . . . . .31
Table 35. FIFODataReg register (address 09h); reset
value: XXh, XXXXXXXXb. . . . . . . . . . . . . . . . .32
Table 36. Description of FIFODataReg bits . . . . . . . . . . .32
Table 37. FIFOLevelReg register (address 0Ah); reset
value: 00h, 00000000b. . . . . . . . . . . . . . . . . . .32
Table 38. Description of FIFOLevelReg bits. . . . . . . . . . .32
Table 39. WaterLevelReg register (address 0Bh); reset
value: 08h, 00001000b. . . . . . . . . . . . . . . . . . .33
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
130 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
reset value: EBh, 11101011b . . . . . . . . . . . . . .51
Table 116. Description of TestSel2Reg bits. . . . . . . . . . . . 62
Table 117. TestPinEnReg register (address 33h); reset
value: 80h, 10000000b . . . . . . . . . . . . . . . . . . 63
Table 118. Description of TestPinEnReg bits . . . . . . . . . . 63
Table 119. TestPinValueReg register (address 34h); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 63
Table 120. Description of TestPinValueReg bits . . . . . . . . 63
Table 121. TestBusReg register (address 35h); reset
value: XXh, XXXXXXXXb . . . . . . . . . . . . . . . . 64
Table 122. Description of TestBusReg bits . . . . . . . . . . . . 64
Table 123. AutoTestReg register (address 36h); reset
value: 40h, 01000000b . . . . . . . . . . . . . . . . . . 64
Table 124. Description of bits . . . . . . . . . . . . . . . . . . . . . . 64
Table 125. VersionReg register (address 37h); reset
value: XXh, XXXXXXXXb . . . . . . . . . . . . . . . . 65
Table 126. Description of VersionReg bits . . . . . . . . . . . . 65
Table 127. AnalogTestReg register (address 38h); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 66
Table 128. Description of AnalogTestReg bits . . . . . . . . . 66
Table 129. TestDAC1Reg register (address 39h); reset
value: XXh, 00XXXXXXb . . . . . . . . . . . . . . . . . 67
Table 130. Description of TestDAC1Reg bits . . . . . . . . . . 67
Table 131. TestDAC2Reg register (address 3Ah); reset
value: XXh, 00XXXXXXb . . . . . . . . . . . . . . . . . 67
Table 132. Description ofTestDAC2Reg bits. . . . . . . . . . . 67
Table 133. TestADCReg register (address 3Bh); reset
value: XXh, XXXXXXXXb . . . . . . . . . . . . . . . . 67
Table 134. Description of TestADCReg bits . . . . . . . . . . . 67
Table 135. RFTReg register (address 3Ch); reset value:
FFh, 11111111b . . . . . . . . . . . . . . . . . . . . . . . . 68
Table 136. Description of RFTReg bits . . . . . . . . . . . . . . . 68
Table 137. RFTReg register (address 3Dh, 3Fh); reset
value: 00h, 00000000b . . . . . . . . . . . . . . . . . . 68
Table 138. Description of RFTReg bits . . . . . . . . . . . . . . . 68
Table 139. RFTReg register (address 3Eh); reset value:
03h, 00000011b . . . . . . . . . . . . . . . . . . . . . . . . 68
Table 140. Description of RFTReg bits . . . . . . . . . . . . . . . 68
Table 141. Connection protocol for detecting different
interface types . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 142. Connection scheme for detecting the different
interface types . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 143. MOSI and MISO byte order . . . . . . . . . . . . . . 70
Table 144. MOSI and MISO byte order . . . . . . . . . . . . . . 71
Table 145. Address byte 0 register; address MOSI . . . . . 71
Table 146. BR_T0 and BR_T1 settings . . . . . . . . . . . . . . 72
Table 147. Selectable UART transfer speeds . . . . . . . . . 72
Table 148. UART framing . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 149. Read data byte order . . . . . . . . . . . . . . . . . . . 73
Table 150. Write data byte order . . . . . . . . . . . . . . . . . . . 73
Table 151. Address byte 0 register; address MOSI . . . . . 75
Table 152. Supported interface types . . . . . . . . . . . . . . . . 82
Table 153. Register and bit settings controlling the
signal on pin TX1 . . . . . . . . . . . . . . . . . . . . . . 84
Table 78. Description of SerialSpeedReg bits . . . . . . . . .51
Table 79. PageReg register (address 20h); reset value:
00h, 00000000b . . . . . . . . . . . . . . . . . . . . . . . .52
Table 80. Description of PageReg bits . . . . . . . . . . . . . . .52
Table 81. CRCResultReg register (address 21h); reset
value: FFh, 11111111b. . . . . . . . . . . . . . . . . . . .52
Table 82. Description of CRCResultReg bits . . . . . . . . . .52
Table 83. CRCResultReg register (address 22h); reset
value: FFh, 11111111b. . . . . . . . . . . . . . . . . . . .52
Table 84. Description of CRCResultReg bits . . . . . . . . . .52
Table 85. GsNOffReg register (address 23h); reset
value: 88h, 10001000b. . . . . . . . . . . . . . . . . . .53
Table 86. Description of GsNOffReg bits . . . . . . . . . . . . .53
Table 87. ModWidthReg register (address 24h); reset
value: 26h, 00100110b . . . . . . . . . . . . . . . . . . .54
Table 88. Description of ModWidthReg bits . . . . . . . . . . .54
Table 89. TxBitPhaseReg register (address 25h); reset
value: 87h, 10000111b . . . . . . . . . . . . . . . . . . .54
Table 90. Description of TxBitPhaseReg bits . . . . . . . . . .54
Table 91. RFCfgReg register (address 26h); reset
value: 48h, 01001000b. . . . . . . . . . . . . . . . . . .55
Table 92. Description of RFCfgReg bits . . . . . . . . . . . . .55
Table 93. GsNOnReg register (address 27h); reset
value: 88h, 10001000b. . . . . . . . . . . . . . . . . . .56
Table 94. Description of GsNOnReg bits . . . . . . . . . . . . .56
Table 95. CWGsPReg register (address 28h); reset
value: 20h, 00100000b. . . . . . . . . . . . . . . . . . .56
Table 96. Description of CWGsPReg bits. . . . . . . . . . . . .56
Table 97. ModGsPReg register (address 29h); reset
value: 20h, 00100000b. . . . . . . . . . . . . . . . . . .57
Table 98. Description of ModGsPReg bits . . . . . . . . . . . .57
Table 99. TModeReg register (address 2Ah); reset
value: 00h, 00000000b. . . . . . . . . . . . . . . . . . .57
Table 100. Description of TModeReg bits . . . . . . . . . . . . .57
Table 101. TPrescalerReg register (address 2Bh); reset
value: 00h, 00000000b. . . . . . . . . . . . . . . . . . .58
Table 102. Description of TPrescalerReg bits . . . . . . . . . .58
Table 103. TReloadReg (Higher bits) register (address
2Ch); reset value: 00h, 00000000b . . . . . . . . .59
Table 104. Description of the higher TReloadReg bits . . .59
Table 105. TReloadReg (Lower bits) register (address
2Dh); reset value: 00h, 00000000b . . . . . . . . .59
Table 106. Description of lower TReloadReg bits . . . . . . .59
Table 107. TCounterValReg (Higher bits) register (address
2Eh); reset value: XXh, XXXXXXXXb . . . . . . .60
Table 108. Description of the higher TCounterValReg bits 60
Table 109. TCounterValReg (Lower bits) register (address
2Fh); reset value: XXh, XXXXXXXXb. . . . . . . .60
Table 110. Description of lower TCounterValReg bits . . . .60
Table 111. PageReg register (address 30h); reset value:
00h, 00000000b . . . . . . . . . . . . . . . . . . . . . . . .60
Table 112. Description of PageReg bits. . . . . . . . . . . . . . .61
Table 113. TestSel1Reg register (address 31h); reset
value: 00h, 00000000b. . . . . . . . . . . . . . . . . . .62
Table 154. Register and bit settings controlling the
signal on pin TX2 . . . . . . . . . . . . . . . . . . . . . . 85
Table 114. Description of TestSel1Reg bits . . . . . . . . . . . .62
Table 115. TestSel2Reg register (address 32h); reset
value: 00h, 00000000b. . . . . . . . . . . . . . . . . . .62
Table 155. Setting of the bits RFlevel in register
RFCfgReg (RFLevel amplifier deactivated) . . . 86
Table 156. CRC coprocessor parameters . . . . . . . . . . . . 93
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
131 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
Table 157. Interrupt sources . . . . . . . . . . . . . . . . . . . . . . .95
Table 158. Command overview . . . . . . . . . . . . . . . . . . .101
Table 159. Testsignal routing (TestSel2Reg = 07h). . . . .107
Table 160. Description of Testsignals . . . . . . . . . . . . . . .107
Table 161. Testsignal routing (TestSel2Reg = 0Dh) . . . .108
Table 162. Description of Testsignals . . . . . . . . . . . . . . .108
Table 163. Testsignal routing (TestSel2Reg = 19h). . . . .108
Table 164. Description of Testsignals . . . . . . . . . . . . . . .108
Table 165. Testsignals description. . . . . . . . . . . . . . . . . .108
Table 166. Limiting values . . . . . . . . . . . . . . . . . . . . . . . 111
Table 167. Operating conditions . . . . . . . . . . . . . . . . . . . 111
Table 168. Thermal characteristics . . . . . . . . . . . . . . . . . 112
Table 169. Characteristics . . . . . . . . . . . . . . . . . . . . . . .112
Table 170. SPI timing characteristics . . . . . . . . . . . . . . . 117
Table 171. I2C-bus timing in Fast mode . . . . . . . . . . . . .117
Table 172. AC symbols . . . . . . . . . . . . . . . . . . . . . . . . . .119
Table 173. Timing specification for separated
Read/Write strobe. . . . . . . . . . . . . . . . . . . . . .119
Table 174. Timing specification for common
Read/Write strobe. . . . . . . . . . . . . . . . . . . . . .120
Table 175. Package information . . . . . . . . . . . . . . . . . . .122
Table 176. Abbreviations . . . . . . . . . . . . . . . . . . . . . . . .126
Table 177. Revision history . . . . . . . . . . . . . . . . . . . . . . .127
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
132 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
36. Figures
Fig 1. Simplified block diagram of the PN512 . . . . . . . . .6
Fig 2. Detailed block diagram of the PN512 . . . . . . . . . .7
Fig 3. Pinning configuration HVQFN32 (SOT617-1) . . . .8
Fig 4. Pinning configuration HVQFN40 (SOT618-1) . . . .8
Fig 5. Pin configuration TFBGA64 (SOT1336-1) . . . . . . .9
Fig 6. PN512 Read/Write mode. . . . . . . . . . . . . . . . . . .14
Fig 7. ISO/IEC 14443 A/MIFARE Read/Write mode
communication diagram. . . . . . . . . . . . . . . . . . . .14
Fig 8. Data coding and framing according to
ISO/IEC 14443 A . . . . . . . . . . . . . . . . . . . . . . . . .15
Fig 9. FeliCa reader/writer communication diagram . . .16
Fig 10. NFCIP-1 mode. . . . . . . . . . . . . . . . . . . . . . . . . . .17
Fig 11. Active communication mode . . . . . . . . . . . . . . . .18
Fig 12. Passive communication mode. . . . . . . . . . . . . . .19
Fig 13. SPI connection to host. . . . . . . . . . . . . . . . . . . . .70
Fig 14. UART connection to microcontrollers . . . . . . . . .71
Fig 15. UART read data timing diagram . . . . . . . . . . . . .73
Fig 16. UART write data timing diagram . . . . . . . . . . . . .74
Fig 17. I2C-bus interface . . . . . . . . . . . . . . . . . . . . . . . . .75
Fig 18. Bit transfer on the I2C-bus . . . . . . . . . . . . . . . . . .76
Fig 19. START and STOP conditions . . . . . . . . . . . . . . .76
Fig 20. Acknowledge on the I2C-bus . . . . . . . . . . . . . . . .77
Fig 21. Data transfer on the I2C-bus . . . . . . . . . . . . . . . .77
Fig 22. First byte following the START procedure . . . . . .78
Fig 23. Register read and write access . . . . . . . . . . . . . .79
Fig 24. I2C-bus HS mode protocol switch . . . . . . . . . . . .80
Fig 25. I2C-bus HS mode protocol frame. . . . . . . . . . . . .81
Fig 26. Connection to host controller with separated
Read/Write strobes . . . . . . . . . . . . . . . . . . . . . . .83
Fig 27. Connection to host controller with common
Read/Write strobes . . . . . . . . . . . . . . . . . . . . . . .83
Fig 28. Data mode detector . . . . . . . . . . . . . . . . . . . . . . .87
Fig 29. Serial data switch for TX1 and TX2 . . . . . . . . . . .88
Fig 30. Communication flows using the S2C interface. . .89
Fig 31. Signal shape for SIGOUT in FeliCa card SAM
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Fig 32. Signal shape for SIGIN in SAM mode . . . . . . . . .90
Fig 33. Signal shape for SIGOUT in MIFARE Card SAM
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Fig 34. Signal shape for SIGIN in MIFARE Card SAM
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Fig 35. Quartz crystal connection . . . . . . . . . . . . . . . . . .99
Fig 36. Oscillator start-up time. . . . . . . . . . . . . . . . . . . .100
Fig 37. Autocoll Command . . . . . . . . . . . . . . . . . . . . . .104
Fig 38. Typical circuit diagram . . . . . . . . . . . . . . . . . . . .110
Fig 39. Pin RX input voltage range . . . . . . . . . . . . . . . .116
Fig 40. Timing diagram for SPI . . . . . . . . . . . . . . . . . . .118
Fig 41. Timing for Fast and Standard mode devices
on the I2C-bus . . . . . . . . . . . . . . . . . . . . . . . . . .118
Fig 42. Timing diagram for separated Read/Write
strobe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Fig 43. Timing diagram for common Read/Write strobe 121
Fig 44. Package outline package version (HVQFN32) .123
Fig 45. Package outline package version (HVQFN40) .124
Fig 46. Package outline package version (TFBGA64). .125
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
133 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
37. Contents
1
1.1
2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
9.2.2.4
9.2.2.5
9.2.2.6
9.2.2.7
9.2.2.8
9.2.2.9
RxModeReg. . . . . . . . . . . . . . . . . . . . . . . . . . 39
TxControlReg. . . . . . . . . . . . . . . . . . . . . . . . . 40
TxAutoReg. . . . . . . . . . . . . . . . . . . . . . . . . . . 41
TxSelReg . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
RxSelReg. . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
RxThresholdReg . . . . . . . . . . . . . . . . . . . . . . 44
Different available versions. . . . . . . . . . . . . . . . 1
General description. . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 3
Quick reference data . . . . . . . . . . . . . . . . . . . . . 4
Ordering information. . . . . . . . . . . . . . . . . . . . . 5
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
4
5
9.2.2.10 DemodReg. . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.2.2.11 FelNFC1Reg . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.2.2.12 FelNFC2Reg . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.2.2.13 MifNFCReg . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.2.2.14 ManualRCVReg. . . . . . . . . . . . . . . . . . . . . . . 49
9.2.2.15 TypeBReg . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.2.2.16 SerialSpeedReg. . . . . . . . . . . . . . . . . . . . . . . 50
6
7
7.1
7.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 8
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pin description . . . . . . . . . . . . . . . . . . . . . . . . 10
8
8.1
8.2
8.3
8.3.1
8.4
8.4.1
8.4.2
8.4.3
8.4.4
8.4.5
8.4.6
Functional description . . . . . . . . . . . . . . . . . . 14
ISO/IEC 14443 A/MIFARE functionality . . . . . 14
ISO/IEC 14443 B functionality . . . . . . . . . . . . 15
FeliCa reader/writer functionality . . . . . . . . . . 16
FeliCa framing and coding . . . . . . . . . . . . . . . 16
NFCIP-1 mode . . . . . . . . . . . . . . . . . . . . . . . . 17
Active communication mode . . . . . . . . . . . . . 18
Passive communication mode . . . . . . . . . . . . 19
NFCIP-1 framing and coding . . . . . . . . . . . . . 20
NFCIP-1 protocol support. . . . . . . . . . . . . . . . 20
MIFARE Card operation mode . . . . . . . . . . . . 20
FeliCa Card operation mode . . . . . . . . . . . . . 21
9.2.3
Page 2: Configuration . . . . . . . . . . . . . . . . . . 52
PageReg . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
CRCResultReg . . . . . . . . . . . . . . . . . . . . . . . 52
GsNOffReg . . . . . . . . . . . . . . . . . . . . . . . . . . 53
ModWidthReg . . . . . . . . . . . . . . . . . . . . . . . . 54
TxBitPhaseReg . . . . . . . . . . . . . . . . . . . . . . . 54
RFCfgReg . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
GsNOnReg . . . . . . . . . . . . . . . . . . . . . . . . . . 56
CWGsPReg . . . . . . . . . . . . . . . . . . . . . . . . . . 56
ModGsPReg . . . . . . . . . . . . . . . . . . . . . . . . . 57
9.2.3.1
9.2.3.2
9.2.3.3
9.2.3.4
9.2.3.5
9.2.3.6
9.2.3.7
9.2.3.8
9.2.3.9
9.2.3.10 TMode Register, TPrescaler Register . . . . . . 57
9.2.3.11 TReloadReg. . . . . . . . . . . . . . . . . . . . . . . . . . 59
9.2.3.12 TCounterValReg . . . . . . . . . . . . . . . . . . . . . . 60
9
9.1
9.1.1
9.2
PN512 register SET . . . . . . . . . . . . . . . . . . . . . 21
PN512 registers overview. . . . . . . . . . . . . . . . 21
Register bit behavior. . . . . . . . . . . . . . . . . . . . 23
Register description . . . . . . . . . . . . . . . . . . . . 24
Page 0: Command and status . . . . . . . . . . . . 24
PageReg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
CommandReg . . . . . . . . . . . . . . . . . . . . . . . . 24
CommIEnReg. . . . . . . . . . . . . . . . . . . . . . . . . 25
DivIEnReg . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CommIRqReg. . . . . . . . . . . . . . . . . . . . . . . . . 27
DivIRqReg . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ErrorReg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Status1Reg. . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Status2Reg. . . . . . . . . . . . . . . . . . . . . . . . . . . 31
9.2.4
Page 3: Test. . . . . . . . . . . . . . . . . . . . . . . . . . 60
PageReg . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
TestSel1Reg. . . . . . . . . . . . . . . . . . . . . . . . . . 62
TestSel2Reg. . . . . . . . . . . . . . . . . . . . . . . . . . 62
TestPinEnReg . . . . . . . . . . . . . . . . . . . . . . . . 63
TestPinValueReg . . . . . . . . . . . . . . . . . . . . . . 63
TestBusReg . . . . . . . . . . . . . . . . . . . . . . . . . . 64
AutoTestReg . . . . . . . . . . . . . . . . . . . . . . . . . 64
VersionReg . . . . . . . . . . . . . . . . . . . . . . . . . . 64
AnalogTestReg. . . . . . . . . . . . . . . . . . . . . . . . 66
9.2.4.1
9.2.4.2
9.2.4.3
9.2.4.4
9.2.4.5
9.2.4.6
9.2.4.7
9.2.4.8
9.2.4.9
9.2.1
9.2.1.1
9.2.1.2
9.2.1.3
9.2.1.4
9.2.1.5
9.2.1.6
9.2.1.7
9.2.1.8
9.2.1.9
9.2.4.10 TestDAC1Reg . . . . . . . . . . . . . . . . . . . . . . . . 67
9.2.4.11 TestDAC2Reg . . . . . . . . . . . . . . . . . . . . . . . . 67
9.2.4.12 TestADCReg . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.2.4.13 RFTReg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
9.2.1.10 FIFODataReg . . . . . . . . . . . . . . . . . . . . . . . . . 32
9.2.1.11 FIFOLevelReg . . . . . . . . . . . . . . . . . . . . . . . . 32
9.2.1.12 WaterLevelReg. . . . . . . . . . . . . . . . . . . . . . . . 33
9.2.1.13 ControlReg . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.2.1.14 BitFramingReg . . . . . . . . . . . . . . . . . . . . . . . . 34
9.2.1.15 CollReg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
10
10.1
10.2
10.2.1
10.2.2
10.2.3
10.3
Digital interfaces . . . . . . . . . . . . . . . . . . . . . . . 68
Automatic microcontroller interface detection 68
Serial Peripheral Interface . . . . . . . . . . . . . . . 70
SPI read data. . . . . . . . . . . . . . . . . . . . . . . . . 70
SPI write data. . . . . . . . . . . . . . . . . . . . . . . . . 70
SPI address byte . . . . . . . . . . . . . . . . . . . . . . 71
UART interface . . . . . . . . . . . . . . . . . . . . . . . 71
Connection to a host . . . . . . . . . . . . . . . . . . . 71
9.2.2
Page 1: Communication . . . . . . . . . . . . . . . . . 36
PageReg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
ModeReg . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
TxModeReg . . . . . . . . . . . . . . . . . . . . . . . . . . 38
9.2.2.1
9.2.2.2
9.2.2.3
10.3.1
continued >>
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
134 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
10.3.2
10.3.3
10.4
Selectable UART transfer speeds . . . . . . . . . 71
18.1
18.2
Reset timing requirements . . . . . . . . . . . . . . . 99
Oscillator start-up time. . . . . . . . . . . . . . . . . . 99
UART framing. . . . . . . . . . . . . . . . . . . . . . . . . 72
I2C Bus Interface . . . . . . . . . . . . . . . . . . . . . . 75
Data validity . . . . . . . . . . . . . . . . . . . . . . . . . . 76
START and STOP conditions . . . . . . . . . . . . . 76
Byte format . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . 77
7-Bit addressing . . . . . . . . . . . . . . . . . . . . . . . 78
Register write access . . . . . . . . . . . . . . . . . . . 78
Register read access . . . . . . . . . . . . . . . . . . . 79
High-speed mode . . . . . . . . . . . . . . . . . . . . . . 80
High-speed transfer . . . . . . . . . . . . . . . . . . . . 80
19
PN512 command set. . . . . . . . . . . . . . . . . . . 100
General description . . . . . . . . . . . . . . . . . . . 100
General behavior . . . . . . . . . . . . . . . . . . . . . 100
PN512 command overview . . . . . . . . . . . . . 101
PN512 command descriptions. . . . . . . . . . . 101
10.4.1
10.4.2
10.4.3
10.4.4
10.4.5
10.4.6
10.4.7
10.4.8
10.4.9
19.1
19.2
19.3
19.3.1
19.3.1.1 Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
19.3.1.2 Config command . . . . . . . . . . . . . . . . . . . . . 101
19.3.1.3 Generate RandomID . . . . . . . . . . . . . . . . . . 102
19.3.1.4 CalcCRC . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
19.3.1.5 Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
19.3.1.6 NoCmdChange . . . . . . . . . . . . . . . . . . . . . . 102
19.3.1.7 Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
19.3.1.8 Transceive . . . . . . . . . . . . . . . . . . . . . . . . . . 103
19.3.1.9 AutoColl . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
19.3.1.10 MFAuthent . . . . . . . . . . . . . . . . . . . . . . . . . . 105
19.3.1.11 SoftReset . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
10.4.10 Serial data transfer format in HS mode . . . . . 80
10.4.11 Switching between F/S mode and HS mode . 82
10.4.12 PN512 at lower speed modes . . . . . . . . . . . . 82
11
11.1
8-bit parallel interface . . . . . . . . . . . . . . . . . . . 82
Overview of supported host controller
interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Separated Read/Write strobe . . . . . . . . . . . . . 83
Common Read/Write strobe . . . . . . . . . . . . . . 83
11.2
11.3
20
Testsignals. . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Selftest. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Testbus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Testsignals at pin AUX. . . . . . . . . . . . . . . . . 108
PRBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
20.1
20.2
20.3
20.4
12
Analog interface and contactless UART . . . . 84
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
TX driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
RF level detector . . . . . . . . . . . . . . . . . . . . . . 85
Data mode detector . . . . . . . . . . . . . . . . . . . . 86
Serial data switch . . . . . . . . . . . . . . . . . . . . . . 88
S2C interface support . . . . . . . . . . . . . . . . . . . 88
Signal shape for Felica S2C interface support 90
Waveform shape for ISO/IEC 14443A and
12.1
12.2
12.3
12.4
12.5
12.6
12.6.1
12.6.2
21
22
23
24
25
Errata sheet . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Application design-in information. . . . . . . . . 110
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 111
Recommended operating conditions . . . . . . 111
Thermal characteristics . . . . . . . . . . . . . . . . . 112
MIFARE S2C support . . . . . . . . . . . . . . . . . . . 91
Hardware support for FeliCa and NFC polling 92
Polling sequence functionality for initiator. . . . 92
Polling sequence functionality for target. . . . . 92
Additional hardware support for FeliCa and
26
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 112
Timing characteristics . . . . . . . . . . . . . . . . . . 117
8-bit parallel interface timing . . . . . . . . . . . . . 119
AC symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 119
AC operating specification . . . . . . . . . . . . . . . 119
12.7
26.1
26.2
26.2.1
26.2.2
12.7.1
12.7.2
12.7.3
NFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
CRC coprocessor . . . . . . . . . . . . . . . . . . . . . . 93
26.2.2.1 Bus timing for separated Read/Write strobe . 119
26.2.2.2 Bus timing for common Read/Write strobe . 120
12.7.4
13
FIFO buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Accessing the FIFO buffer . . . . . . . . . . . . . . . 94
Controlling the FIFO buffer . . . . . . . . . . . . . . . 94
FIFO buffer status information . . . . . . . . . . . . 94
27
28
29
30
31
32
Package information. . . . . . . . . . . . . . . . . . . 122
Package outline. . . . . . . . . . . . . . . . . . . . . . . 123
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . 126
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
References. . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Revision history . . . . . . . . . . . . . . . . . . . . . . 127
13.1
13.2
13.3
14
14.1
15
Interrupt request system. . . . . . . . . . . . . . . . . 95
Interrupt sources overview . . . . . . . . . . . . . . . 95
Timer unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
33
Legal information . . . . . . . . . . . . . . . . . . . . . 128
Data sheet status . . . . . . . . . . . . . . . . . . . . . 128
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . 128
Licenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . 129
16
Power reduction modes . . . . . . . . . . . . . . . . . 98
Hard power-down . . . . . . . . . . . . . . . . . . . . . . 98
Soft power-down mode. . . . . . . . . . . . . . . . . . 98
Transmitter power-down mode. . . . . . . . . . . . 98
33.1
33.2
33.3
33.4
33.5
16.1
16.2
16.3
17
18
Oscillator circuitry. . . . . . . . . . . . . . . . . . . . . . 99
Reset and oscillator start-up time . . . . . . . . . 99
continued >>
PN512
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 4.5 — 17 December 2013
111345
135 of 136
PN512
NXP Semiconductors
Full NFC Forum compliant solution
34
35
36
37
Contact information. . . . . . . . . . . . . . . . . . . . 129
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2013.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 17 December 2013
111345
相关型号:
PN5120A0HN/C2
SPECIALTY TELECOM CIRCUIT, PQCC40, 6 X 6 MM, 0.85 MM HEIGHT, PLASTIC, MO-220, SOT618-1, VQFN-40
NXP
PN5120A0HN1/C1
SPECIALTY TELECOM CIRCUIT, PQCC32, 5 X 5 MM X 0.85 MM HEIGHT, PLASTIC, SOT-617, HVQFN-32
NXP
PN5127
Small Signal Bipolar Transistor, 0.1A I(C), 1-Element, NPN, Silicon, TO-92, PLASTIC, TO-92, 3 PIN
CDIL
PN5127-18F
Small Signal Bipolar Transistor, 12V V(BR)CEO, 1-Element, NPN, Silicon, TO-92, TO-92-18F, 3 PIN
CENTRAL
PN5127-18FLEADFREE
Small Signal Bipolar Transistor, 12V V(BR)CEO, 1-Element, NPN, Silicon, TO-92, TO-92-18F, 3 PIN
CENTRAL
PN5127-18RLEADFREE
Small Signal Bipolar Transistor, 12V V(BR)CEO, 1-Element, NPN, Silicon, TO-92, TO-92-18R, 3 PIN
CENTRAL
©2020 ICPDF网 联系我们和版权申明