SA57255-20GW-G [NXP]
IC 0.3 A SWITCHING CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO5, 1.50 MM, PLASTIC, MO-178, SOT-25, SOT-23, SOP-5, Switching Regulator or Controller;
| 型号： | SA57255-20GW-G |
| 厂家： | 
NXP |
| 描述： | IC 0.3 A SWITCHING CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO5, 1.50 MM, PLASTIC, MO-178, SOT-25, SOT-23, SOP-5, Switching Regulator or Controller 开关 光电二极管 |
| 文件： | 总17页 (文件大小：238K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
SA57255-XX
CMOS switching regulator
(PWM controlled)
Product data
2003 Nov 11
Supersedes data of 2001 Aug 01
Philips
Semiconductors
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
GENERAL DESCRIPTION
The SA57255-XX is a highly integrated DC/DC converter circuit.
Efficient, compact power conversion is achieved with a pulse width
modulation (PWM) controlled switching regulator circuit designed
using CMOS processing. Low ripple and high efficiency of typically
83% are achieved through PWM control. The regulator has a high
precision output with ±2.4% accuracy. Few external components are
required.
The SA57255-XX has a built-in, soft-start circuit to reduce current
inrush and voltage overshoot during start up. The PWM control
circuit is designed to drive an external low resistance NPN bipolar
junction transistor (BJT). The DRIVE output provides typically 7 mA
at 100 kHz typical switching frequency to drive the BJT.
FEATURES
• Operates from 0.7 to 9 V
APPLICATIONS
• Mobile and portable phones
DC
• Ultra low operating supply current—typically 17 µA
• Uses external power BJT
• Instrumentation and industrial products
• Other portable, battery-operated equipment
• High efficiency—typically 83%
• High precision output—typically ±2.4%
• Operating temperature range of –40 to +85 °C
• Available output voltages: 2.0, 2.5, 2.8, 3.0, 3.3, 3.6, 5.0 V
DC
• Available in a 5-lead small outline surface mount package
(SOP003)
SIMPLIFIED SYSTEM DIAGRAM
V
OUT
V
2
FB
1
DD
V
BATT
V
SA57255-XX
REF
R
R
DRIVE
5
PWM CONTROL
GND
4
SOFT START
SA57255-XX as a boost (step-up) converter.
SL01508
Figure 1. Simplified system diagram.
2
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
ORDERING INFORMATION
PACKAGE
TEMPERATURE
RANGE
TYPE NUMBER
NAME
DESCRIPTION
VERSION
SOT23-5,
SOT25, SO5
SA57255-XXGW
Plastic small outline package; 5 leads; body width 1.6 mm
SOP003
–40 to +85 °C
NOTE:
Part number marking
The device has seven voltage output options, indicated by the XX
on the Type Number.
Each device is marked with a four letter code. The first three letters
designate the product. The fourth letter, represented by ‘x’, is a date
tracking code.
XX
20
25
28
30
33
36
50
VOLTAGE (Typical)
Part number
Marking
A E T x
A E U x
A E V x
A E W x
A E X x
A E Y x
A E Z x
2.0 V
2.5 V
2.8 V
3.0 V
3.3 V
3.6 V
5.0 V
SA57255-20GW
SA57255-25GW
SA57255-28GW
SA57255-30GW
SA57255-33GW
SA57255-36GW
SA57255-50GW
PIN CONFIGURATION
PIN DESCRIPTION
PIN SYMBOL
DESCRIPTION
1
FB
Feedback from the output voltage to the PWM
control.
FB
DD
1
2
3
5
DRIVE
2
3
4
5
V
DD
Voltage input to regulator.
No connection.
V
N/C
GND
DRIVE
Ground.
N/C
4
GND
Output for external power transistor.
SL01509
Figure 2. Pin configuration.
MAXIMUM RATINGS
SYMBOL
PARAMETER
MIN.
–0.3
–0.3
–0.3
–
MAX.
11
UNIT
V
V
V
V
FB pin voltage
FB
Power supply voltage
DRIVE pin voltage
DRIVE pin current
Operating temperature
Storage temperature
Power dissipation
11
V
DD(max)
DRIVE
11
V
I
300
+85
+125
150
mA
°C
DRIVE
T
–40
–40
–
oper
T
stg
°C
P
D
mW
3
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
ELECTRICAL CHARACTERISTICS
T
amb
= 25 °C, unless otherwise specified.
SYMBOL
PARAMETER
input voltage
CONDITIONS
Part #
–
MIN.
–
TYP.
–
MAX.
9.0
UNIT
V
V
V
V
V
IN
operating start voltage
oscillator start voltage
operation hold voltage
consumption current 1
I
I
= 1.0 mA
= 1.0 mA
–
–
–
0.9
V
ST1
ST2
HLD
OUT
–
0.7
0.7
–
–
0.8
V
–
–
–
V
OUT
-20
-25
-28
-30
-33
-36
-50
-20
-25
-28
-30
-33
-36
-50
-20
-25
-28
-30
-33
-36
-50
-20
-25
-28
-30
-33
-36
-50
–
14.5
17.8
20.0
21.4
23.7
28.8
54.0
3.8
24.1
29.7
33.3
35.7
39.5
48.0
89.9
7.6
µA
I
I
I
I
V
= output voltage × 0.95
SS1
OUT
–
µA
–
µA
–
µA
–
µA
–
µA
–
µA
–
µA
consumption current 2
V
OUT
= output voltage + 0.5 V
SS2
–
3.9
7.7
µA
–
3.9
7.8
µA
–
3.9
7.8
µA
–
4.0
7.9
µA
–
4.0
7.9
µA
–
4.2
8.3
µA
–
–1.9
–2.7
–2.7
–3.5
–3.5
–3.5
–5.3
3.8
–2.9
–4.0
–4.0
–5.3
–5.3
–5.3
–8.0
5.7
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mV
ppm/°C
DRIVE pin output current
(HIGH)
V
= V
– 0.4 V
OUT
DRIVEH
DRIVE
–
–
–
–
–
–
–
DRIVE pin output current
(LOW)
V
= 0.4 V
DRIVEL
DRIVE
–
5.3
8.0
–
5.3
8.0
–
7.0
10.5
10.5
10.5
16
–
7.0
–
7.0
–
10.7
30
∆V
∆V
load ripple voltage
I
= 10 mA ≈ I (following) × 1.25
OUT
–
60
OUT2
OUT
/∆T
output voltage temperature
coefficient
–40 °C ≤ T ≤ +85 °C
amb
–
–
±50
–
OUT
amb
f
oscillator frequency
maximum duty ratio
soft start time
V
V
= output voltage × 0.95
= output voltage × 0.95
–
85
80
3.0
–
100
83
6.0
76
80
80
84
84
84
88
115
86
12
–
kHz
%
OSC
OUT
MaxDuty
–
OUT
t
SS
I
= 1.0 mA
–
ms
%
OUT
-20
-25
-28
-30
-33
-36
-50
E
efficiency
FFI
–
–
%
–
–
%
–
–
%
–
–
%
–
–
%
–
–
%
4
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
TYPICAL PERFORMANCE CURVES
25
5
4
3
2
1
0
V
= OUTPUT VOLTAGE × 0.95
V
= OUTPUT VOLTAGE = 0.5 V
OUT
OUT
20
15
10
5
I
I
SS2
SS1
µ
µ
A)
(
A)
(
0
–40
–20
0
20
40
60
80
100
–40
–20
0
20
40
60
80
100
T , TEMPERATURE °C)
amb
T , TEMPERATURE °C)
amb
SL01489
SL01490
Figure 3. Supply current 1 versus temperature.
Figure 4. Supply current 2 versus temperature.
140
50
V
= OUTPUT VOLTAGE × 0.95
T
amb
= 25 °C
OUT
130
120
110
100
90
40
30
20
10
f
OSC
(kHz)
I
SS1, 2
(µA)
80
70
0
60
–40
–20
0
20
40
60
80
100
0
2
4
6
8
10
T , TEMPERATURE °C)
amb
V
(V)
OUT
SL01491
SL01459
Figure 5. Oscillator frequency versus temperature.
Figure 6. Supply current 1, 2 versus V
.
OUT
–16
V
= V
OUT
– 0.4 V
DRIVE
–14
–12
–10
–8
I
DRIVEH
(mA)
–6
–4
–2
0
–40
–20
0
20
40
60
80
100
T , TEMPERATURE °C)
amb
SL01492
Figure 7. DRIVE pin output current HIGH versus temperature.
5
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
V
= 1.8 V
V
= 1.8 V
IN
IN
V
OUT
V
OUT
OUTPUT VOLTAGE
(20 mV/div)
OUTPUT VOLTAGE
(20 mV/div)
V
SW
V
SW
SW VOLTAGE
(1 V/div)
SW VOLTAGE
(1 V/div)
t (10 µs/div)
t (10 µs/div)
SL01472
= 1.8 V
SL01473
= 60 mA
Figure 8. Ripple voltage with light load.
Figure 9. Ripple voltage with medium load.
I
V
OUT
IN
V
V
OUT
IN
OUTPUT VOLTAGE
(20 mV/div)
INPUT VOLTAGE
(1 V/div)
V
V
SW
OUT
SW VOLTAGE
(1 V/div)
OUTPUT VOLTAGE
(1 V/div)
t (10 µs/div)
t (1 ms/div)
SL01474
SL01475
Figure 10. Ripple voltage with heavy load.
Figure 11. Start-up characteristic V : 0 V → 1.8 V.
IN
I : 100 µA → 50 mA; V = 1.8 V
OUT IN
I
= 60 mA; V = 1.8 V
IN
OUT
V
I
OUT
LOAD CURRENT
(20 mA/div)
ON/OFF
INPUT VOLTAGE
(1 V/div)
V
V
OUT
OUTPUT VOLTAGE
(50 mV/div)
OUT
OUTPUT VOLTAGE
(1 V/div)
t (1 ms/div)
t (200 µs/div)
SL01476
SL01477
Figure 12. Start-up characteristic V
: 0 V → 3.0 V.
ON/OFF
Figure 13. Output load regulation, increasing current.
6
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
I
: 50 mA → 100 µA; V = 1.8 V
V
: 1.8 V → 2.4 V; I
= 50 mA
OUT
OUT
IN
IN
I
OUT
LOAD CURRENT
(20 mA/div)
V
IN
INPUT VOLTAGE
(500 mV/div)
V
OUT
V
OUT
OUTPUT VOLTAGE
(50 mV/div)
OUTPUT VOLTAGE
(50 mV/div)
t (5 ms/div)
t (100 µs/div)
SL01478
SL01479
Figure 14. Output load regulation, decreasing current.
Figure 15. Input line regulation, increasing voltage.
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
V
: 2.4 V → 1.8 V; I
= 50 mA
OUT
IN
V
IN
INPUT VOLTAGE
(500 mV/div)
V
OUT
V
V
ST1
DO
0.2
0.1
0.0
OUTPUT VOLTAGE
(50 mV/div)
0
1
2
3
4
5
6
7
8
9
10
t (200 µs/div)
I , OUTPUT CURRENT (mA)
OUT
SL01480
SL01481
Figure 16. Input line regulation, decreasing voltage.
Figure 17. Output current versus starting voltage.
7
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
TECHNICAL DISCUSSION
The SA57255-XX requires an external NPN bipolar transistor to
provide the switching power waveform. Its internal block diagram is
shown in Figure 18.
General discussion
The SA57255-XX is a fixed frequency, boost-mode switching power
supply controller. Each device is set to provide a fixed output voltage
by having a fully compensated internal voltage feedback loop. The
SA57255-XX operates at a fixed frequency of 100 kHz and can
operate from a single alkaline cell (0.9 V) or up to 9 V.
2
V
FB
2
DD
V
SA57255-XX
REF
R
R
DRIVE
5
PWM CONTROL
GND
4
SOFT START
SL01510
Figure 18. Functional diagram.
8
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
APPLICATION INFORMATION
The SA57255-XX can be used for a simple boost (step-up)
converter or the less commonly used flyback converter (isolated
boost). The major operating restriction of the simple boost converter
PASSIVE SNUBBER
(OPTIONAL)
is that its output voltage must always be above the highest
L
0
V
V
IN
expected value of the input voltage. The flyback converter circuit
requires more parts, but the output voltage is not restricted by the
input voltage.
D
OUT
V
FB
DD
C
C
IN
OUT
Boost converter fundamentals
SA57255-XX
The boost or step-up converter is a non-dielectrically isolated
switching power supply topology (arrangement of power parts).
That is, the input power source is directly connected to the output
load (ground and signals). A typical boost converter, with an optional
passive snubber, can be seen in Figure 19.
DRIVE
GND
To understand the boost converter’s operation, examine its three
periods of operation. These periods are: the power switch on-time
(period 1); the inductor discharge period (period 2); and the inductor
empty state (period 3). These periods and their associated currents
can be seen in Figure 20.
SL01511
Figure 19. Boost converter.
SPIKE
ENERGY BEING TRANSFERRED TO OUTPUT
+V
OUT
ENERGY BEING
STORED IN INDUCTOR
CORE EMPTY,
PARASITIC CIRCULATING ENERGY
+V
IN
PERIOD 2
PERIOD 1
PERIOD 3
I
× R
DS(ON)
SW
0
I
peak
V
IN
(V – V
)
IN
OUT
L
0
L
0
SL01464
Figure 20. Boost converter waveforms (discontinuous mode).
9
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
Period 1: power switch on-time
Period 3: inductor empty state
During this period, a simple circuit loop is formed when the power
switch is on. The input voltage source is connected directly across
DISCONTINUOUS MODE—This period as displayed in Figure 20 occurs
in the discontinuous–mode of operation of a boost converter. It is
identified by a period of “ringing” following the output period
(period 2). The inductor has been completely emptied of its stored
energy and the switched node returns to the level of the input
voltage. Ringing is seen at this node because a resonant circuit is
the boost inductor (L ). A current ramp is exhibited whose slope is
0
described by:
VIN
Eqn. (1)
IL(on)
+
L0
formed by the inductance of L and any parasitic inductances and
0
Energy is then stored within the core material of the inductor and is
described by:
capacitances connected to that node. This ringing has very little
energy and can easily be eliminated by a small passive snubber.
2
CONTINUOUS MODE—If the inductor is not completely emptied of its
stored energy before the power switch turns on again, the converter
is operating in the continuous mode. A small amount of residual flux
(energy) remains in the inductor core and the current waveform
jumps to an initial value when the power switch is again turned-on.
This mode offers some advantages over the discontinuous-mode,
because the peak current seen by the power switch is lower. In low
voltage applications, the inductor can store more energy with lower
peak currents.
Eqn. (2)
Esto + 0.5L0 Ipeak
This current ramp continues until the controller turns off the power
switch.
Period 2: inductor discharge period
The instant the power switch turns off, the current flowing through
the inductor forces the voltage at its output node (switched node) to
rise quickly above the input voltage (spike). This voltage is then
clamped when it exceeds the device’s output voltage and the output
rectifier becomes forward biased. The inductor empties its stored
energy in the form of a linearly decreasing current ramp whose
slope is dictated by:
The continuous mode waveforms can be seen in Figure 21.
VIN * VOUT
Eqn. (3)
IL(off)
[
L0
The stored energy is transferred to the output capacitor. This output
current continues until the magnetic core is completely emptied of its
stored energy or the power switch turns back on.
SPIKE
+V
OUT
+V
IN
ENERGY BEING
STORED IN
INDUCTOR
ENERGY BEING
TRANSFERRED
TO OUTPUT
0
V
IN
L
I
0
peak
(V – V
)
IN
OUT
L
0
RESIDUAL FLUX
SL01465
Figure 21. Continuous mode waveforms.
10
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
Selecting the external NPN transistor
A ceramic capacitor would typically be used in this application if the
required value is less than 1 – 10 µF, or a tantalum capacitor for
required values of 10 µF and above. Lower cost aluminum electrolytic
capacitors can be used, but you should confirm that the higher ESRs
typically exhibited by these capacitors does not cause a problem.
The SA57255-XX requires an external NPN bipolar transistor to
provide the PWM switching waveform to the boost power circuit.
The type of bipolar transistor for this power range includes higher
current “small signal” transistors or “medium power” transistors.
Minimum transistor parameters are:
The minimum value of the output capacitor can be estimated by
Equation (7).
Case: minimum P
800 mW (such as SOT223)
D(max)
HFE
100
20 V
500 mA minimum
(min)
(IOUT(max)) (Toff
)
VCEO
IC
Eqn. (7)
COUT
Where:
u
Vripple(p*p)
(max)
A good choice for 0.5 watts and below is the PZT2222A, which
exceeds these specifications.
I
is the average value of the output load current (A).
OUT
T
V
is the nominal off–time of the power switch (sec) [ 10 µs].
off
Determining the value of the boost inductor
is the desired amount of ripple voltage (V ).
p–p
ripple
The precise value of the boost inductor is not critical to the operation
of the SA57255-XX. The value of the boost inductor should be
calculated to provide continuous-mode operation over most of its
operating range. The converter may enter the discontinuous-mode
when the output load current falls to less than about 20 percent of
the full-load current.
Finding the value of the input capacitor is done by Equation (8).
(Ipeak) (Ton
Vdrop
)
Eqn. (8)
CIN
Where:
u
At low input voltages, the time required to store the needed energy
lengthens, but the time needed to empty the inductor’s core of its
energy shrinks. Conversely, at high input voltages, the time needed
to store the energy shrinks while the time needed to empty the core
increases. See Equations (1) and (3). At the extremes of these
conditions, the converter will fall out of regulation, that is the output
voltage will begin to fall, because the time needed for either storing
or emptying the stored inductor energy is too short to support the
output load current.
I
T
V
is the expected maximum peak current of the switch (A).
is the on-time of the switch (sec) [ 10 µs].
is the desired amount of voltage drop across the capacitor
peak
on
drop
(V ).
p–p
These calculations should produce a good estimate of the needed
values of the input and output capacitors to yield the desired ripple
voltages.
Selecting the output rectifier
Equation (4) determines the nominal value of the inductance.
The output rectifier (D) is critical to the efficiency and low-noise
operation of the boost converter. The majority of the loss within the
supply will be caused by the output rectifier. Three parameters are
important in the rectifier’s operation within a boost-mode supply.
These are defined below.
VIN(min) Ton
Eqn. (4)
L0 ^
Ipeak
Where:
V
T
is the lowest expected input operating voltage (V).
is about 5 µs or one-half the switching period (s).
IN(min)
Forward voltage drop (V )—This is the voltage across the rectifier
f
on
when a forward current is flowing through the rectifier. A P-N
ultra-fast diode exhibits a 0.7 – 1.4 volt drop, and this drop is
relatively fixed over the range of forward currents. A Schottky diode
exhibits a 0.3 – 0.6 volt drop and appears more resistive during the
forward conduction periods. That is, its forward voltage drop
increases with increasing currents. You can gain an advantage by
purposely over-rating the current rating of a Schottky rectifier.
I
is the maximum peak current for the NPN transistor.
peak
This is an estimated inductor value and you can select an
inductance value slightly higher or lower with little effect on the
converter’s operation. If the design falls out of regulation within the
desired operating range, reduce the inductance value, but by no
more than 30 percent.
Determining the minimum value of the capacitors
Reverse recovery time (T )—This is an issue when the boost
rr
The input and output capacitors experience the current waveforms
seen in Figures 20 and 21. The peak currents can be typically
between 3 to 6 times the average currents flowing into the input and
from the output. This makes the choice of capacitor an issue of how
much ripple voltage can be tolerated on the capacitor’s terminals
and how much heating the capacitor can tolerate. At the power
levels produced by the SA57255-XX heating is not a major issue.
supply is operating in the continuous-mode. T is the amount of time
rr
required for the rectifier to assume an open circuit when a forward
current is flowing and a reverse voltage is then placed across its
terminals. P-N ultra-fast rectifiers typically have a 25–40 ns reverse
recovery time. Schottky rectifiers have a very short or no reverse
recovery time.
Forward recovery time (T )—This is the amount of time before a
fr
The Equivalent Series Resistance (ESR) of the capacitor, the
resistance that appears between its terminals, and the actual
capacitance causes heat to be generated within the case whenever
there is current entering or exiting the capacitor. ESR also adds to
the apparent voltage drop across the capacitor. The heat that is
generated can be approximated by Equation (5).
rectifier begins conducting forward current after a forward voltage is
placed across its terminals. This parameter is not always well
specified by the rectifier manufacturers. It causes a spike to appear
when the power switch turns off. This particular point in its operation
causes the most radiated noise. Several rectifiers may have to be
evaluated for the prototype. After the final output rectifier selection is
made, if the spike is still causing a problem a small passive snubber
can be placed across the rectifier.
2
Eqn. (5)
PD(in watts) ^ (1.8Iav
)
(RESR
)
ESR’s effect on the capacitor voltage is given by Equation (6).
For this boost application, the best choice of output rectifier is a low
forward drop, 0.5 – 1 ampere, 20 volt Schottky rectifier such as the
Philips part number BAT120A.
Eqn. (6)
DVC ^ Ipeak(RESR
)
(expressed as V
)
p–p
11
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
Flyback converter
The SA57255-XX can also be used to create a flyback converter,
COILTRONICS
CTX100-1P
V
V
OUT
IN
also known as an isolated boost converter. The advantage of a
flyback converter is that the input voltage can go higher or lower
than the output voltage without affecting the operation of the
converter. The only restrictions are the breakdown voltage of the
C
OUT
C
IN
NPN transistor and the feedback (V ) pins.
FB
V
DD
One transformer can accommodate a variety of output voltages in
different applications, because the circuit will change the on and
off–times to provide the desired output voltage.
DRIVE
FB
SA57255-XX
The output voltage of the flyback can be changed by using a
SA57255-XX with the desired output voltage, with no other changes
to the circuit.
GND
Selecting the components
It is best to operate the transformer in the continuous-mode where
the highest expected peak primary current is below the maximum
current rating of the NPN transistor.
SL01512
Figure 22. Flyback converter circuit.
Begin with a peak current equal to or less than the maximum current
rating of the NPN transistor. A reasonable value of the primary
inductance can be found in Equation (9).
Ton
Ipeak
Eqn. (9)
V
+ V
OUT
Lpri t 5VIN(min)
IN
(1:1 TRANSFORMER)
Where:
V
IN
I
is the current rating of the NPN transistor.
peak
T
on
is the maximum expected on-time of the switch (≈10 µs).
V
is the lowest expected input voltage (V).
IN(min)
Then select an off-the-shelf transformer such as the Coiltronics
CTX100–1P, a 1:1 turns ratio transformer that has a primary
inductance of 100 µH. It does not reach saturation until the primary
current reaches 440 mA, which is above the expected peak current
of the flyback converter. The 1:1 turns ratio should work for output
voltages from 0.8 to 2 times the highest input voltage, and produce
the output voltage set by the SA57255-XX. The only other restriction
is that the input voltage plus the output voltage must be less than
the breakdown voltage of the NPN transistor.
+V
OUT
GROUND (0 V)
Use Equation (8) to determine the minimum value for the input
capacitor. A 0.1 V drop is desired across this capacitor.
–V
IN
(0.3A) (10ms)
CIN
u
+ 30mF
0.1V
A 47 µF at 6 V tantalum capacitor would be suitable.
For the design example, the output voltage will be +3.3 V with a
maximum output current of 50 mA. The input voltage can vary
between +1.8 V and 4.0 V. The design can be seen in Figure 22,
and the expected waveforms can be seen in Figure 23.
I
SW(peak)
V
IN
I
= I
diode
peak
I
diode(peak)
(1:1 TRANSFORMER)
SL01468
Figure 23. Flyback converter waveforms.
12
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
Designing a passive snubber
If the switching power supply is generating too much radio
PASSIVE SNUBBER
V
V
OUT
IN
frequency interference (RFI) a passive snubber can be added.
A passive snubber is a series resistor and capacitor placed across
any component that exhibits a resonant “ringing”. This series R-L-C
loop creates a lossy or damped tank circuit that dissipates the
ringing energy. The design is critical, because it introduces another
loss within the converter.
C
OUT
C
IN
Designing a snubber is an empirical process, mainly because it
involves undefined parasitic capacitances and inductances
contributed by the PCB layout, leakage inductance, and device
capacitances. The snubber should be placed across the major
source of the spike or ringing which is the output rectifier.
V
DD
FB
SA57255-XX
DRIVE
GND
The usual design process is:
1. Measure the period of the undesired ringing (T ).
0
SL01513
2. Place a very small ceramic capacitor (about 10 pF) across the
output rectifier or primary winding.
Figure 24. Flyback converter with passive snubber.
3. Re-measure the period of the undesired ringing. The new period
should be about 3 times that of T . If it is less than this, place a
0
slightly larger value of capacitor across the output rectifier or
primary winding.
4. Once the desired increase in the ringing period is achieved with
a capacitance (C ), place a resistor in series with the capacitor
0
whose value is approximately:
T0
Eqn. (10)
Rsnubber
^
2pC0
This should produce a snubber that does not load the circuit and
introduces a very small loss.
13
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
Designing the PCB for effective heat dissipation
Laying out the printed circuit board
The maximum junction temperature is +125 °C which should not be
exceeded under any operating conditions. Designing a PCB that
includes a heatsink system under the device is the key to cooler
operation of the circuit, and the long–term reliable operation of the
converter.
The design of the printed circuit board (PCB) is critical to the proper
operation of all switching power supplies. Its design affects the
supply stability, radio frequency interference behavior and the
reliability of the converter.
Never use the autoroute feature of any PCB design program
because this will always produce traces that are too long and too
thin.
The major sources of heat within the converter are the power switch
(NPN BJT), the resistive losses within the inductor, and losses
associated with the output rectifier. These losses can be estimated
by the following equations:
The input and output capacitors are the only source or sink of the
high frequency currents found in a switching power supply. All
connections to the switching power supply from the outside circuits
should be made to the input or output capacitor terminals (+ and –).
Internally, the layout should adhere to a “one-point” grounding
system, as shown in Figure 25.
Power switch:
fsw Ton Ipeak Vsat
Eqn. (11)
PD(sw)
^
2
Inductor:
Eqn. (12)
PD(L0) ^ 2Ipk 2Rwinding
L
0
Output rectifier:
V
V
IN
OUT
Eqn. (13)
PD(rect) ^ IOUT(Vfwd)
V
FB
DD
The thermal resistance (R
) of the SA57255-XX is approximately
th(j-a)
C
C
220 °C/W, assuming the device is soldered to a 2 oz. copper FR4
fiberglass circuit board, and that the minimum footprint was used
(copper just under the leads). A rule of thumb in PCB design is that
the thermal resistance can be reduced by 30% for each doubling of
the copper area close to the device. This effect diminishes for areas
greater than five times the minimum PCB footprint. If you take
advantage of this rule, thermal resistance can be reduced by using
wide copper lands when connecting to the leads of the major
power-producing parts. These PCB traces should almost fill the
areas surrounding the converter parts to conduct heat away from
the device. For demanding applications, additional heat dissipation
area can be created by placing a copper island on the opposite side
of the PCB from each wide trace and connecting it to the trace with
vias (plated thru holes).
IN
OUT
EXT
SA57251-XX
INPUT
OUTPUT
GROUND
TO ONE
POINT
GROUND
TO ONE
POINT
GND
SL01514
Figure 25. Grounding trace for converter.
The traces between the input and output capacitors and the
inductor, power switch and rectifier(s) should be as short and wide
as possible. This reduces the series resistance and inductance that
can be introduced by traces.
The junction temperature can be estimated by Equation (14).
Eqn. (14)
Tj ^ (PD Rth(j-a)Ȁ) ) Tamb(max)
Where:
The guidelines for a PCB layout can be summarized as:
P
D
is the power dissipation (W).
R
′ is the effective thermal resistance with the additional
copper (°C/W).
is the highest local expected ambient temperature (°C).
• The traces between the input and output capacitor to the inductor,
power switch and the rectifier should be made as short and as
wide as possible.
th(j-a)
T
amb
• Strictly adhere to the one-point wiring practices shown in
Figure 25.
• On a 2-sided board, do not run sensitive signals traces under the
AC voltage node.
• The IC (control) ground is terminated at the output capacitor’s
negative terminal.
14
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
PACKING METHOD
The SA57255-XX is packed in reels, as shown in Figure 26.
GUARD
BAND
TAPE
TAPE DETAIL
REEL
ASSEMBLY
COVER TAPE
CARRIER TAPE
BARCODE
LABEL
BOX
SL01305
Figure 26. Tape and reel packing method.
15
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
Plastic small outline package; 5 leads; body width 1.6 mm
SOP003
16
2003 Nov 11
Philips Semiconductors
Product data
CMOS switching regulator (PWM controlled)
SA57255-XX
REVISION HISTORY
Rev
Date
Description
_2
20031111
Product data (9397 750 12318). ECN 853-2273 30332 of 09 September 2003.
Supersedes data of 2001 Aug 01 (9397 750 08904).
Modifications:
• Change package outline version to SOP003 in Ordering information table and Package outline sections.
_1
20010801
Product data (9397 750 08904). ECN 853-2273 26807 of 01 August 2001.
Data sheet status
Product
status
Definitions
[1]
Level
Data sheet status
[2] [3]
I
Objective data
Development
This data sheet contains data from the objective specification for product development.
Philips Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data
Qualification
Production
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
[1] Please consult the most recently issued data sheet before initiating or completing a design.
[2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL
http://www.semiconductors.philips.com.
[3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see
the relevant data sheet or data handbook.
Limitingvaluesdefinition— Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given
in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no
representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be
expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree
to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes in the products—including circuits, standard cells, and/or software—described
or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated
viaaCustomerProduct/ProcessChangeNotification(CPCN).PhilipsSemiconductorsassumesnoresponsibilityorliabilityfortheuseofanyoftheseproducts,conveys
nolicenseortitleunderanypatent, copyright, ormaskworkrighttotheseproducts, andmakesnorepresentationsorwarrantiesthattheseproductsarefreefrompatent,
copyright, or mask work right infringement, unless otherwise specified.
Koninklijke Philips Electronics N.V. 2003
Contact information
All rights reserved. Printed in U.S.A.
For additional information please visit
http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
Date of release: 11-03
9397 750 12318
For sales offices addresses send e-mail to:
sales.addresses@www.semiconductors.philips.com.
Document order number:
Philips
Semiconductors
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明