SAF1562HL/N2,518_技术文档

SAF1562

Hi-Speed Universal Serial Bus PCI Host Controller

Rev. 01 — 7 February 2007

Product data sheet

1. General description

The SAF1562HL is a Peripheral Component Interconnect (PCI)-based, single-chip

Universal Serial Bus (USB) Host Controller. It integrates two Original USB Open Host

Controller Interface (OHCI) cores, one Hi-Speed USB Enhanced Host Controller Interface

(EHCI) core, and two transceivers that are compliant with Hi-Speed USB and Original

USB. The functional parts of the SAF1562HL are fully compliant with Universal Serial Bus

Speciﬁcation Rev. 2.0, Open Host Controller Interface Speciﬁcation for USB Rev. 1.0a,

Enhanced Host Controller Interface Speciﬁcation for Universal Serial Bus Rev. 1.0, PCI

Local Bus Speciﬁcation Rev. 2.2, and PCI Bus Power Management Interface Speciﬁcation

Rev. 1.1.

The integrated high performance USB transceivers allow the SAF1562HL to handle all

Hi-Speed USB transfer speed modes: high-speed (480 Mbit/s), full-speed (12 Mbit/s) and

low-speed (1.5 Mbit/s). The SAF1562HL provides two downstream ports, allowing

simultaneous connection of USB devices at different speeds.

The SAF1562HL is fully compatible with various operating system drivers, such as

Microsoft Windows standard OHCI and EHCI drivers that are present in Windows XP,

Windows 2000 and Red Hat Linux.

The SAF1562HL directly interfaces to any 32-bit, 33 MHz PCI bus. Its PCI pins can source

3.3 V. The PCI interface fully complies with PCI Local Bus Speciﬁcation Rev. 2.2.

The SAF1562HL is ideally suited for use in Hi-Speed USB mobile applications and

embedded solutions. The SAF1562HL uses a 12 MHz crystal.

2. Features

I Complies with Universal Serial Bus Speciﬁcation Rev. 2.0

I Supports data transfer at high-speed (480 Mbit/s), full-speed (12 Mbit/s) and

low-speed (1.5 Mbit/s)

I Two Original USB OHCI cores comply with Open Host Controller Interface

Speciﬁcation for USB Rev. 1.0a

I One Hi-Speed USB EHCI core complies with Enhanced Host Controller Interface

Speciﬁcation for Universal Serial Bus Rev. 1.0

I Supports PCI 32-bit, 33 MHz interface compliant with PCI Local Bus Speciﬁcation

Rev. 2.2, with support for D3_coldstandby and wake-up modes; all I/O pins are 3.3 V

standard

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

I Compliant with PCI Bus Power Management Interface Speciﬁcation Rev. 1.1 for all

hosts (EHCI and OHCI), and supports all power states: D0, D1, D2, D3_hotand D3_cold

I CLKRUN support for mobile applications, such as internal notebook design

I Conﬁgurable subsystem ID and subsystem vendor ID through external EEPROM

I Digital and analog power separation for better Electro-Magnetic Interference (EMI) and

ElectroStatic Discharge (ESD) protection

I Supports hot plug and play and remote wake-up of peripherals

I Supports individual power switching and individual overcurrent protection for

downstream ports

I Supports partial dynamic port-routing capability for downstream ports that allows

sharing of the same physical downstream ports between the Original USB Host

Controller and the Hi-Speed USB Host Controller

I Uses 12 MHz crystal oscillator to reduce system cost and EMI emissions

I Supports dual power supply: PCI V_aux(3V3)and V_CC

I Operates at +3.3 V power supply input

I Low power consumption

I Qualiﬁed in accordance with AEC-Q100

I Operating temperature range from −40 °C to +85 °C

I Available in LQFP100 package

3. Applications

I Car radio

I Digital consumer appliances

I Notebook

I PCI add-on card

I PC motherboard

I Set-Top Box (STB)

I Web appliances

4. Ordering information

Table 1.

Ordering information

Type number

Package

Name

Description

Version

SAF1562HL

LQFP100

plastic low proﬁle quad ﬂat package; 100 leads; body 14 × 14 × 1.4 mm

SOT407-1

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

2 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

6. Pinning information

6.1 Pinning

1

75

74

73

72

71

70

69

68

67

66

65

64

63

62

61

60

59

58

57

56

55

54

53

GNDA

XTAL2

XTAL1

AUX1V8

GNDA

2

AUX1V8

3

V

I(VAUX3V3)

INTA#

4

5

RST#

GNDD

PCICLK

GNT#

V

CC(I/O)

6

AD[0]

AD[1]

7

8

AD[2]

9

REQ#

AD[3]

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

AD[31]

AD[4]

V

AD[5]

CC(I/O)

AD[30]

AD[29]

AD[28]

AD[27]

GNDD

AD[6]

SAF1562HL

AD[7]

GNDA

C/BE#[0]

AD[8]

V

I(VREG3V3)

GNDA

REG1V8

GNDD

REG1V8

AD[9]

AD[26]

AD[25]

AD[24]

C/BE#[3]

IDSEL

AD[10]

V

CC(I/O)

AD[11]

AD[12]

52 AD[13]

51

V

AD[14]

CC(I/O)

008aaa026

Fig 2. Pin conﬁguration for LQFP100

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

4 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

6.2 Pin description

Table 2.

Symbol^[1]

GNDA

Pin description

1

Type Description

-

analog ground

AUX1V8

2

1.8 V auxiliary output voltage; only for voltage conditioning; cannot be

used to supply power to external components; connected to 100 nF

and 20 µF capacitors

V_I(VAUX3V3)

INTA#

3

4

-

3.3 V auxiliary input voltage; add a 100 nF decoupling capacitor

PCI interrupt

O

PCI pad; 3.3 V signaling; open-drain

RST#

5

I

PCI reset; used to bring PCI-speciﬁc registers, sequencers and

signals to a consistent state

3.3 V input pad; push-pull

GNDD

6

7

-

I

digital ground

PCICLK

PCI system clock (33 MHz)

PCI pad; 3.3 V signaling

GNT#

REQ#

8

9

I/O

PCI grant; indicates to the agent that access to the bus is granted

PCI pad; 3.3 V signaling

PCI request; indicates to the arbitrator that the agent wants to use the

bus

PCI pad; 3.3 V signaling

AD[31]

10

I/O

bit 31 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

V_CC(I/O)

AD[30]

11

12

-

3.3 V supply voltage; used to power pads; add a 100 nF decoupling

capacitor

I/O

bit 30 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

AD[29]

AD[28]

AD[27]

13

14

15

I/O

bit 29 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 28 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 27 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

V_I(VREG3V3)16

-

3.3 V regulator input voltage; add a 100 nF decoupling capacitor

analog ground

GNDA

17

18

REG1V8

1.8 V regulator output voltage; only for voltage conditioning; cannot

be used to supply power to external components; connected to

100 nF and 20 µF capacitors

GNDD

AD[26]

19

20

-

digital ground

I/O

bit 26 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

AD[25]

AD[24]

21

22

I/O

bit 25 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 24 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

5 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 2.

Pin description …continued

Symbol^[1]

Type Description

C/BE#[3]

23

I/O

byte 3 of multiplexed PCI bus command and byte enable

PCI pad; 3.3 V signaling

IDSEL

24

I

PCI initialization device select; used as a chip select during

conﬁguration read and write transactions

PCI pad; 3.3 V signaling

V_CC(I/O)

AD[23]

25

26

-

3.3 V supply voltage; used to power pads; add a 100 nF decoupling

capacitor

I/O

bit 23 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

AD[22]

AD[21]

AD[20]

AD[19]

AD[18]

27

28

29

30

31

I/O

bit 22 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 21 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 20 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 19 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 18 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

GNDD

AD[17]

32

33

-

digital ground

I/O

bit 17 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

AD[16]

34

35

36

I/O

bit 16 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

C/BE#[2]

FRAME#

byte 2 of multiplexed PCI bus command and byte enable

PCI pad; 3.3 V signaling

PCI cycle frame; driven by the master to indicate the beginning and

duration of an access

PCI pad; 3.3 V signaling

IRDY#

37

38

39

I/O

PCI initiator ready; indicates the ability of the initiating agent to

complete the current data phase of a transaction

PCI pad; 3.3 V signaling

TRDY#

PCI target ready; indicates the ability of the target agent to complete

the current data phase of a transaction

PCI pad; 3.3 V signaling

DEVSEL#

PCI device select; indicates if any device is selected on the bus

PCI pad; 3.3 V signaling

V_CC(I/O)

STOP#

40

41

-

3.3 V supply voltage; used to power pads; add a 100 nF decoupling

capacitor

I/O

PCI stop; indicates that the current target is requesting the master to

stop the current transaction

PCI pad; 3.3 V signaling

CLKRUN# 42

I/O

PCI CLKRUN signal; pull-down to ground through a 10 kΩ resistor

PCI pad; 3.3 V signaling; open-drain

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

6 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 2.

Pin description …continued

Symbol^[1]

Type Description

REG1V8

43

-

1.8 V regulator output voltage; only for voltage conditioning; cannot

be used to supply power to external components; add a 100 nF

decoupling capacitor

PERR#

SERR#

44

45

I/O

PCI parity error; used to report data parity errors during all PCI

transactions, except a Special Cycle

PCI pad; 3.3 V signaling

O

PCI system error; used to report address parity errors and data parity

errors on the Special Cycle command, or any other system error in

which the result will be catastrophic

PCI pad; 3.3 V signaling; open-drain

analog ground

GNDA

PAR

46

47

-

I/O

PCI parity

PCI pad; 3.3 V signaling

C/BE#[1]

48

I/O

byte 1 of multiplexed PCI bus command and byte enable

PCI pad; 3.3 V signaling

GNDD

AD[15]

49

50

-

digital ground

I/O

bit 15 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

AD[14]

AD[13]

AD[12]

AD[11]

51

52

53

54

I/O

bit 14 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 13 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 12 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 11 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

V_CC(I/O)

AD[10]

55

56

-

3.3 V supply voltage; used to power pads; add a 100 nF decoupling

capacitor

I/O

bit 10 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

AD[9]

57

58

I/O

-

bit 9 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

REG1V8

1.8 V regulator output voltage; only for voltage conditioning; cannot

be used to supply power to external components; add a 100 nF

decoupling capacitor

AD[8]

59

60

I/O

bit 8 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

C/BE#[0]

byte 0 of multiplexed PCI bus command and byte enable

PCI pad; 3.3 V signaling

GNDA

AD[7]

61

62

-

analog ground

I/O

bit 7 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

AD[6]

63

I/O

bit 6 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

7 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 2.

Pin description …continued

Symbol^[1]

64

Type Description

GNDD

-

digital ground

AD[5]

65

I/O

bit 5 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

AD[4]

AD[3]

AD[2]

AD[1]

AD[0]

V_CC(I/O)

66

67

68

69

70

71

I/O

-

bit 4 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 3 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 2 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 1 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

bit 0 of multiplexed PCI address and data

PCI pad; 3.3 V signaling

3.3 V supply voltage; used to power pads; add a 100 nF decoupling

capacitor

GNDA

72

73

-

analog ground

AUX1V8

1.8 V auxiliary output voltage; only for voltage conditioning; cannot be

used to supply power to external components; add a 100 nF

decoupling capacitor

XTAL1

XTAL2

GNDD

74

75

76

AI

AO

-

crystal oscillator input; this can also be a 12 MHz clock input

crystal oscillator output (12 MHz); leave open when clock is used

digital ground

V_{CC(I/O)_AUX}77

-

3.3 V auxiliary supply voltage; used to power pads; add a 100 nF

decoupling capacitor

OC1_N

78

79

I

overcurrent sense input for the USB downstream port 1 (digital)

3.3 V input pad; push-pull; CMOS

PWE1_N

O

power enable for the USB downstream port 1

3.3 V output pad; 3 ns slew rate control; CMOS; open-drain

analog ground

GNDA

RREF

GNDA

DM1

80

81

82

83

-

AI/O analog connection for the external resistor (12 kΩ ± 1 %)

analog ground

-

AI/O D−; analog connection for the USB downstream port 1; leave this pin

open when not in use

GNDA

DP1

84

85

-

analog ground

AI/O D+; analog connection for the USB downstream port 1; leave this pin

open when not in use

V_{DDA_AUX}

OC2_N

86

87

-

I

auxiliary analog supply voltage; add a 100 nF decoupling capacitor

overcurrent sense input for the USB downstream port 2 (digital)

3.3 V input pad; push-pull; CMOS

PWE2_N

GNDA

88

89

O

-

power enable for the USB downstream port 2

3.3 V output pad; 3 ns slew rate control; CMOS; open-drain

analog ground

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

8 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 2.

Pin description …continued

Symbol^[1]

Type Description

DM2

90

AI/O D−; analog connection for the USB downstream port 2; leave this pin

open when not in use

GNDA

DP2

91

92

-

analog ground

AI/O D+; analog connection for the USB downstream port 2; leave this pin

open when not in use

V_{DDA_AUX}

GNDD

SCL

93

94

95

96

-

auxiliary analog supply voltage; add a 100 nF decoupling capacitor

digital ground

-

digital ground

I/O

I²C-bus clock; pull-up to 3.3 V through a 10 kΩ resistor^[2]

I²C-bus pad; clock signal

SDA

97

I/O

I²C-bus data; pull-up to 3.3 V through a 10 kΩ resistor^[2]

I²C-bus pad; data signal

V_{CC(I/O)_AUX}98

PME# 99

-

3.3 V auxiliary supply voltage; used to power pads; add a 100 nF

decoupling capacitor

O

PCI Power Management Event; used by a device to request a

change in the device or system power state

PCI pad; 3.3 V signaling; open-drain

V_{CC(I/O)_AUX}100

-

3.3 V auxiliary supply voltage; used to power pads; add a 100 nF

decoupling capacitor

[1] Symbol names ending with # represent active LOW signals for PCI pins, for example: NAME#. Symbol

names ending with underscore N represent active LOW signals for USB pins, for example: NAME_N.

[2] Connect to ground if I²C-bus is not used.

7. Functional description

7.1 OHCI Host Controller

An OHCI Host Controller per port transfers data to devices at the Original USB deﬁned bit

rate of 12 Mbit/s or 1.5 Mbit/s.

7.2 EHCI Host Controller

The EHCI Host Controller transfers data to a Hi-Speed USB compliant device at the

Hi-Speed USB deﬁned bit rate of 480 Mbit/s. When the EHCI Host Controller has the

ownership of a port, the OHCI Host Controllers are not allowed to modify the port register.

All additional port bit deﬁnitions required for the Enhanced Host Controller are not visible

to the OHCI Host Controller.

7.3 Dynamic port-routing logic

The port-routing feature allows sharing of the same physical downstream ports between

the Original USB Host Controller and the Hi-Speed USB Host Controller. This requirement

of the Enhanced Host Controller Interface Speciﬁcation for Universal Serial Bus Rev. 1.0

provides ports that are multiplexed with the ports of the OHCI.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

9 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

The EHCI is responsible for the port-routing switching mechanism. Two register bits are

used for ownership switching. During power-on and system reset, the default ownership of

all downstream ports is the OHCI. The Enhanced Host Controller Driver (EHCD) controls

the ownership during normal functionality.

7.4 Hi-Speed USB analog transceivers

The Hi-Speed USB analog transceivers directly interface to the USB cables through

integrated termination resistors. These transceivers can transmit and receive serial data

at all data rates: high-speed (480 Mbit/s), full-speed (12 Mbit/s) and low-speed

(1.5 Mbit/s).

7.5 Power management

The SAF1562HL provides an advanced power management capability interface that is

compliant with PCI Bus Power Management Interface Speciﬁcation Rev. 1.1. Power is

controlled and managed by the interaction between drivers and PCI registers.

For a detailed description on power management, see Section 10.

7.6 Phase-Locked Loop (PLL)

A 12 MHz-to-30 MHz and 48 MHz clock multiplier PLL is integrated on-chip. This allows

the use of a low-cost 12 MHz crystal, which also minimizes EMI. No external components

are required for the PLL to operate.

7.7 Power-On Reset (POR)

Figure 3 shows a possible curve of V_CC(I/O)with dips at t2 to t3 and t4 to t5. At t0, POR will

start with 1. At t1, the detector passes through the trip level. Another delay will be added

before POR drops to 0 to ensure that the length of the generated detector pulse, POR, is

large enough to reset asynchronous ﬂip-ﬂops. If the dip is too short (t4 to t5 < 11 µs),

POR will not react and will stay LOW.

V

CC(I/O)

V

POR(trip)

t4

t0

t1

t3

t5

t2

POR

004aaa664

V_POR(trip)is typically 1.2 V.

Fig 3. Power-on reset

7.8 Power supply

Figure 4 shows the SAF1562HL power supply connection.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

10 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

SAF1562HL

V

I(VREG3V3)

16

PCI 3.3 V

100 nF

V

CC(I/O)

11, 25,

40, 55, 71

100 nF

I(VAUX3V3)

(1)

3

PCI V

aux(3V3)

CC(I/O)_AUX

77, 98, 100

86, 93

PCI V

aux(3V3)

100 nF

V

DDA_AUX

(1)

aux(3V3)

AUX1V8

2

100 nF

20 µF

73

18

100 nF

REG1V8

4.7 µF

100 nF

REG1V8

43, 58

100 nF

1, 6, 17, 19, 32,

46, 49, 61, 64,

72, 76, 80, 82,

84, 89, 91, 94, 95

008aaa027

GND

(1) If V_aux(3V3)is not present on PCI, the pin should be connected to PCI 3.3 V.

Fig 4. Power supply connection

8. PCI

8.1 PCI interface

The PCI interface has three functions. The ﬁrst function (#0) and the second function (#1)

are for the OHCI Host Controllers, and the third function (#2) is for the EHCI Host

Controller. All functions support both master and target accesses, and share the same

PCI interrupt signal INTA#. These functions provide memory-mapped, addressable

operational registers as required in Open Host Controller Interface Speciﬁcation for USB

Rev. 1.0a and Enhanced Host Controller Interface Speciﬁcation for Universal Serial Bus

Rev. 1.0.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

11 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Each function has its own conﬁguration space. The PCI enumerator should allocate the

memory address space for each of these functions. Power management is implemented

in each PCI function and all power states are provided. This allows the system to achieve

low power consumption by switching off the functions that are not required.

8.1.1 PCI conﬁguration space

PCI Local Bus Speciﬁcation Rev. 2.2 requires that each of the three PCI functions of the

SAF1562HL provides its own PCI conﬁguration registers, which can vary in size. In

addition to the basic PCI conﬁguration header registers, these functions implement

capability registers to support power management.

The registers of each of these functions are accessed by the respective driver. Section 8.2

provides a detailed description of the various PCI conﬁguration registers.

8.1.2 PCI initiator and target

A PCI initiator initiates PCI transactions to the PCI bus. A PCI target responds to PCI

transactions as a slave. In the case of the SAF1562HL, the two Open Host Controllers

and the Enhanced Host Controller function as both initiators or targets of PCI transactions

issued by the host CPU.

All USB Host Controllers have their own operational registers that can be accessed by the

system driver software. Drivers use these registers to conﬁgure the Host Controller

hardware system, issue commands to it, and monitor the status of the current hardware

operation. The Host Controller plays the role of a PCI target. All operational registers of

the Host Controllers are the PCI transaction targets of the CPU.

Normal USB transfers require the Host Controller to access system memory ﬁelds, which

are allocated by USB HCDs and PCI drivers. The Host Controller hardware interacts with

the HCD by accessing these buffers. The Host Controller works as an initiator in this case

and becomes a PCI master.

8.2 PCI conﬁguration registers

The OHCI USB Host Controllers and the EHCI USB Host Controller contain two sets of

software-accessible hardware registers: PCI conﬁguration registers and memory-mapped

Host Controller registers.

A set of conﬁguration registers is implemented for each of the three PCI functions of the

SAF1562HL, see Table 3.

Remark: In addition to the normal PCI header, from offset index 00h to 3Fh,

implementation-speciﬁc registers are deﬁned to support power management and

function-speciﬁc features.

Table 3.

PCI conﬁguration space registers of OHCI1, OHCI2 and EHCI

Address Bits 31 to 24 Bits 23 to 16 Bits 15 to 8

Bits 7 to 0

Reset value^[1]

Func0 OHCI1 Func1 OHCI2 Func2 EHCI

PCI conﬁguration header registers

00h

04h

Device ID[15:0]

Status[15:0]

Vendor ID[15:0]

1561 1131h

1562 1131h

Command[15:0]

0210 0000h

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

12 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 3.

PCI conﬁguration space registers of OHCI1, OHCI2 and EHCI …continued

Address Bits 31 to 24 Bits 23 to 16 Bits 15 to 8

Bits 7 to 0

Reset value^[1]

Func0 OHCI1 Func1 OHCI2 Func2 EHCI

08h

0Ch

Class Code[23:0]

Revision

ID[7:0]

0C03 1011h

0080 0000h

0000 0000h

0C03 2011h

0080 0000h

0000 0000h

reserved

Header

Type[7:0]

Latency

Timer[7:0]

Cache Line 0080 0000h

Size[7:0]

10h

14h

18h

1Ch

20h

24h

28h

2Ch

30h

34h

Base Address 0[31:0]

0000 0000h

reserved

0000 0000h

Subsystem ID[15:0]

Subsystem Vendor ID[15:0] 1561 1131h

1561 1131h

0000 0000h

0000 00DCh

1562 1131h

0000 0000h

0000 00DCh

reserved

0000 0000h

Capabilities 0000 00DCh

Pointer[7:0]

38h

3Ch

reserved

0000 0000h

Max_ Lat[7:0] Min_Gnt[7:0]

Interrupt

Pin[7:0]

Interrupt

Line[7:0]

2A01 0100h

1002 0100h

40h

reserved

Retry

TRDY

0000 8000h

time-out

Enhanced Host Controller-speciﬁc PCI registers

60h PORTWAKECAP[15:0] FLADJ[7:0]

Power management registers

SBRN[7:0]

-

0007 2020h

DCh

PMC[15:0]

Next_Item_Ptr Cap_ID[7:0]

[7:0]

D282 0001h

FE82 0001h

E0h

Data[7:0]

PMCSR_BSE

[7:0]

PMCSR[15:0]

0000 XX00h^[2]0000 XX00h^[2]0000 XX00h^[2]

[1] Reset values that are highlighted—for example, 0—indicate read and write accesses; and reset values that are not highlighted—for

example, 0—indicate read-only.

[2] See Section 8.2.3.4.

The HCD does not usually interact with the PCI conﬁguration space. The conﬁguration

space is used only by the PCI enumerator to identify the USB Host Controller and assign

appropriate system resources by reading the Vendor ID (VID) and the Device ID (DID).

8.2.1 PCI conﬁguration header registers

The Enhanced Host Controller implements the normal PCI header register values, except

the values for the memory-mapping base address register, serial bus number and Device

ID.

8.2.1.1 Vendor ID register

This read-only register identiﬁes the manufacturer of the device. PCI Special Interest

Group (PCI-SIG) assigns valid vendor identiﬁers to ensure the uniqueness of the

identiﬁer. The bit description is shown in Table 4.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

13 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 4.

VID - Vendor ID register (address 00h) bit description

Legend: * reset value

Bit Symbol

Access Value

1131h*

Description

15 to 0 VID[15:0]

R

Vendor ID: This read-only register value is assigned

to NXP Semiconductors by PCI-SIG as 1131h.

8.2.1.2 Device ID register

This is a 2 B read-only register that identiﬁes a particular device. The identiﬁer is allocated

by NXP Semiconductors. Table 5 shows the bit description of the register.

Table 5.

DID - Device ID register (address 02h) bit description

Legend: * reset value

Bit Symbol

15 to 0 DID[15:0]

Access Value

Description

R

156Xh*^[1]Device ID: This register value is deﬁned by NXP

Semiconductors to identify the USB Host Controller

IC product.

[1] X is 1h for OHCI1 and OHCI2; X is 2h for EHCI.

8.2.1.3 Command register

This is a 2 B register that provides coarse control over the ability of a device to generate

and respond to PCI cycles. The bit allocation of the Command register is given in Table 6.

When logic 0 is written to this register, the device is logically disconnected from the PCI

bus for all accesses, except conﬁguration accesses. All devices are required to support

this base level of functionality. Individual bits in the Command register may or may not

support this base level of functionality.

Table 6.

Bit

Command register (address 04h) bit allocation

15

14

13

12

11

10

9

FBBE

0

8

SERRE

0

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

6

0

R/W

4

0

R/W

3

0

R/W

2

R/W

1

R/W

0

7

5

Symbol

Reset

Access

SCTRL

PER

0

VGAPS

MWIE

0

SC

0

BM

0

MS

0

IOS

0

R

R/W

R

R/W

R

R/W

[1] The reserved bits should always be written with the reset value.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

14 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 7.

Command register (address 04h) bit description

Bit

Symbol

reserved

FBBE

Description

15 to 10

9

-

Fast Back-to-Back Enable: This bit controls whether a master can do

fast back-to-back transactions to various devices. The initialization

software must set this bit if all targets are fast back-to-back capable.

0 — Fast back-to-back transactions are only allowed to the same agent

(value after RST#).

1 — The master is allowed to generate fast back-to-back transactions to

different agents.

8

SERRE

SERR# Enable: This bit is an enable bit for the SERR# driver. All devices

that have an SERR# pin must implement this bit. Address parity errors

are reported only if this bit and the PER bit are logic 1.

0 — Disable the SERR# driver.

1 — Enable the SERR# driver.

7

6

SCTRL

PER

Stepping Control: This bit controls whether a device does address and

data stepping. Devices that never do stepping must clear this bit. Devices

that always do stepping must set this bit. Devices that can do either, must

make this bit read and write, and initialize it to logic 1 after RST#.

Parity Error Response: This bit controls the response of a device to

parity errors. When the bit is set, the device must take its normal action

when a parity error is detected. When the bit is logic 0, the device sets

DPE (bit 15 in the Status register) when an error is detected, but does not

assert PERR# and continues normal operation. The state of this bit after

RST# is logic 0. Devices that check parity must implement this bit.

Devices are required to generate parity, even if parity checking is

disabled.

5

VGAPS

VGA Palette Snoop: This bit controls how VGA compatible and graphics

devices handle accesses to VGA palette registers.

0 — The device should treat palette write accesses like all other

accesses.

1 — Palette snooping is enabled, that is, the device does not respond to

palette register writes and snoops data.

VGA compatible devices should implement this bit.

4

3

MWIE

Memory Write and Invalidate Enable: This is an enable bit for using the

Memory Write and Invalidate command.

0 — Memory Writes must be used instead. State after RST# is logic 0.

1 — Masters may generate the command.

This bit must be implemented by master devices that can generate the

Memory Write and Invalidate command.

SC

Special Cycles: Controls the action of a device on Special Cycle

operations.

0 — Causes the device to ignore all Special Cycle operations. State after

RST# is logic 0.

1 — Allows the device to monitor Special Cycle operations.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

15 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 7.

Command register (address 04h) bit description …continued

Bit

Symbol

Description

2

BM

Bus Master: Controls the ability of a device to act as a master on the PCI

bus.

0 — Disables the device from generating PCI accesses. State after

RST# is logic 0.

1 — Allows the device to behave as a bus master.

1

0

MS

Memory Space: Controls the response of a device to Memory Space

accesses.

0 — Disables the device response. State after RST# is logic 0.

1 — Allows the device to respond to memory space accesses.

IO Space: Controls the response of a device to I/O space accesses.

0 — Disables the device response. State after RST# is logic 0.

1 — Allows the device to respond to I/O space accesses.

IOS

8.2.1.4 Status register

The Status register is a 2 B read-only register used to record status information on PCI

bus-related events. For bit allocation, see Table 8.

Table 8.

Bit

Status register (address 06h) bit allocation

15

14

13

12

RTA

0

11

STA

0

10

9

8

Symbol

Reset

Access

Bit

DPE

SSE

RMA

DEVSELT[1:0]

MDPE

0

R

2

1

R

1

0

R

0

R

7

FBBC

0

6

5

66MC

0

4

3

Symbol

Reset

Access

reserved

CL

1

reserved

0

R

Table 9.

Bit

Status register (address 06h) bit description

Symbol

Description

15

DPE

Detected Parity Error: This bit must be set by the device whenever it

detects a parity error, even if the parity error handling is disabled.

14

13

12

11

SSE

RMA

RTA

STA

Signaled System Error: This bit must be set whenever the device asserts

SERR#. Devices that never assert SERR# do not need to implement this

bit.

Received Master Abort: This bit must be set by a master device whenever

its transaction, except for Special Cycle, is terminated with Master-Abort.

All master devices must implement this bit.

Received Target Abort: This bit must be set by a master device whenever

its transaction is terminated with Target-Abort. All master devices must

implement this bit.

Signaled Target Abort: This bit must be set by a target device whenever it

terminates a transaction with Target-Abort. Devices that never signal

Target-Abort do not need to implement this bit.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

16 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 9.

Bit

10 and 9 DEVSELT DEVSEL Timing: These bits encode the timing of DEVSEL#. There are

Status register (address 06h) bit description …continued

Symbol Description

[1:0]

three allowable timing to assert DEVSEL#:

00b — Fast

01b — Medium

10b — Slow

11b — Reserved

These bits are read-only and must indicate the slowest time that a device

asserts DEVSEL# for any bus command, except Conﬁguration Read and

Conﬁguration Write.

8

7

MDPE

Master Data Parity Error: This bit is implemented by bus masters. It is set

when the following three conditions are met:

• The bus agent asserted PERR# itself, on a read; or observed PERR#

asserted, on a write

• The agent setting the bit acted as the bus master for the operation in

which error occurred

• PER (bit 6 in the Command register) is set

FBBC

Fast Back-to-Back Capable: This read-only bit indicates whether the

target is capable of accepting fast back-to-back transactions when the

transactions are not to the same agent. This bit can be set to logic 1, if the

device can accept these transactions; and must be set to logic 0 otherwise.

6

5

reserved

66MC

-

66 MHz Capable: This read-only bit indicates whether this device is

capable of running at 66 MHz.

0 — 33 MHz

1 — 66 MHz

4

CL

Capabilities List: This read-only bit indicates whether this device

implements the pointer for a new capabilities linked list at offset 34h.

0 — No new capabilities linked list is available

1 — The value read at offset 34h is a pointer in conﬁguration space to a

linked list of new capabilities

3 to 0

reserved

-

8.2.1.5 Revision ID register

This 1 B read-only register indicates a device-speciﬁc revision identiﬁer. The value is

chosen by the vendor. This ﬁeld is a vendor-deﬁned extension of the Device ID. The

Revision ID register bit description is given in Table 10.

Table 10. REVID - Revision ID register (address 08h) bit description

Legend: * reset value

Bit

Symbol

Access Value

11h*

Description

7 to 0 REVID[7:0]

R

Revision ID: This byte speciﬁes the design revision

number of functions.

8.2.1.6 Class Code register

Class Code is a 24-bit read-only register used to identify the generic function of the

device, and in some cases, a speciﬁc register-level programming interface. Table 11

shows the bit allocation of the register.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

17 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

The Class Code register is divided into three byte-size ﬁelds. The upper byte is a base

class code that broadly classiﬁes the type of function the device performs. The middle

byte is a sub-class code that identiﬁes more speciﬁcally the function of the device. The

lower byte identiﬁes a speciﬁc register-level programming interface, if any, so that

device-independent software can interact with the device.

Table 11. Class Code register (address 09h) bit allocation

Bit

23

22

21

20

BCC[7:0]

0Ch

19

18

17

16

Symbol

Reset

Access

Bit

R

15

14

13

12

11

10

9

8

Symbol

Reset

Access

Bit

SCC[7:0]

03h

R

7

6

5

4

3

2

1

0

Symbol

Reset

Access

RLPI[7:0]

X0h^[1]

R

[1] X is 1h for OHCI1 and OHCI2; X is 2h for EHCI.

Table 12. Class Code register (address 09h) bit description

Bit

Symbol

Description

23 to 16

BCC[7:0]

Base Class Code: 0Ch is the base class code assigned to this byte. It

implies a serial bus controller.

15 to 8

7 to 0

SCC[7:0]

RLPI[7:0]

Sub-Class Code: 03h is the sub-class code assigned to this byte. It

implies the USB Host Controller.

Register-Level Programming Interface: 10h is the programming

interface code assigned to OHCI, which is USB 1.1 speciﬁcation

compliant. 20h is the programming interface code assigned to EHCI,

which is USB 2.0 speciﬁcation compliant.

8.2.1.7 Cache Line Size register

The Cache Line Size register is a read and write single-byte register that speciﬁes the

system Cache Line size in units of double word. This register must be implemented by

master devices that can generate the Memory Write and Invalidate command. The value

in this register is also used by master devices to determine whether to use Read, Read

Line or Read Multiple command to access the memory.

Slave devices that want to allow memory bursting using a Cache Line-wrap addressing

mode must implement this register to know when a burst sequence wraps to the

beginning of the Cache Line.

This ﬁeld must be initialized to logic 0 on activation of RST#. Table 13 shows the bit

description of the Cache Line Size register.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

18 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 13. CLS - Cache Line Size register (address 0Ch) bit description

Legend: * reset value

Bit Symbol Access Value Description

7 to 0 CLS[7:0]

R/W

00h*

Cache Line Size: This byte identiﬁes the system

Cache Line size.

8.2.1.8 Latency Timer register

This register speciﬁes—in units of PCI bus clocks—the value of the Latency Timer for the

PCI bus master. Table 14 shows the bit description of the Latency Timer register.

Table 14. LT - Latency Timer register (address 0Dh) bit description

Legend: * reset value

Bit

Symbol Access

LT[7:0] R/W

Value

Description

7 to 0

00h*

Latency Timer: This byte identiﬁes the latency timer.

8.2.1.9 Header Type register

The Header Type register identiﬁes the layout of the second part of the predeﬁned header,

beginning at byte 10h in conﬁguration space. It also identiﬁes whether the device contains

multiple functions. For bit allocation, see Table 15.

Table 15. Header Type register (address 0Eh) bit allocation

Bit

7

MFD

1

6

5

4

3

2

1

0

Symbol

Reset

Access

HT[6:0]

0

R

Table 16. Header Type register (address 0Eh) bit description

Bit

Symbol

Description

7

MFD

Multi-Function Device: This bit identiﬁes a multifunction device.

0 — The device has single function

1 — The device has multiple functions

6 to 0

HT[6:0]

Header Type: These bits identify the layout of the part of the

predeﬁned header, beginning at byte 10h in conﬁguration space.

8.2.1.10 Base Address register 0

Power-up software must build a consistent address map before booting the machine to an

operating system. This means it must determine how much memory is in the system, and

how much address space the I/O controllers in the system require. After determining this

information, power-up software can map the I/O controllers into reasonable locations and

proceed with system boot. To do this mapping in a device-independent manner, the base

registers for this mapping are placed in the predeﬁned header portion of conﬁguration

space.

Bit 0 in all Base Address registers is read-only and used to determine whether the register

maps into memory or I/O space. Base Address registers that map to memory space must

return logic 0 in bit 0. Base Address registers that map to I/O space must return logic 1 in

bit 0.

The bit description of the BAR 0 register is given in Table 17.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

19 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 17. BAR 0 - Base Address register 0 (address 10h) bit description

Legend: * reset value

Bit Symbol

Access Value Description

31 to 0 BAR 0[31:0] R/W

0000

Base Address to Memory-Mapped Host Controller

0000h* Register Space: The memory size required by OHCI

and EHCI are 4 kB and 256 B, respectively. Therefore,

BAR 0[31:12] is assigned to the two OHCI ports, and

BAR 0[31:8] is assigned to the EHCI port.

8.2.1.11 Subsystem Vendor ID register

The Subsystem Vendor ID register is used to uniquely identify the expansion board or

subsystem where the PCI device resides. This register allows expansion board vendors to

distinguish their boards, even though the boards may have the same Vendor ID and

Device ID.

Subsystem Vendor IDs are assigned by PCI-SIG to maintain uniqueness. The bit

description of the Subsystem Vendor ID register is given in Table 18.

Table 18. SVID - Subsystem Vendor ID register (address 2Ch) bit description

Legend: * reset value

Bit

Symbol

Access Value

Description

15 to 0 SVID[15:0]

R

1131h* Subsystem Vendor ID: 1131h is the subsystem

Vendor ID assigned to NXP Semiconductors.

8.2.1.12 Subsystem ID register

Subsystem ID values are vendor speciﬁc. The bit description of the Subsystem ID register

is given in Table 19.

Table 19. SID - Subsystem ID register (address 2Eh) bit description

Legend: * reset value

Bit

Symbol

Access Value

Description

15 to 0 SID[15:0]

R

156Xh*^[1]Subsystem ID: For the SAF1562HL, NXP

Semiconductors has deﬁned OHCI functions as

1561h, and the EHCI function as 1562h.

[1] X is 1h for OHCI1 and OHCI2; X is 2h for EHCI.

8.2.1.13 Capabilities Pointer register

This register is used to point to a linked list of new capabilities implemented by the device.

This register is only valid if CL (bit 4 in the Status register) is set. If implemented, bit 1 and

bit 0 are reserved and should be set to 00b. Software should mask these bits off before

using this register as a pointer in conﬁguration space to the ﬁrst entry of a linked list of

new capabilities. The bit description of the register is given in Table 20.

Table 20. CP - Capabilities Pointer register (address 34h) bit description

Legend: * reset value

Bit

Symbol Access Value

DCh*

Description

7 to 0 CP[7:0]

R

Capabilities Pointer: EHCI efﬁciently manages power

using this register. This Power Management register is

allocated at offset DCh. Only one Host Controller is

needed to manage power in the SAF1562HL.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

20 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

8.2.1.14 Interrupt Line register

This is a 1 B register used to communicate interrupt line routing information. This register

must be implemented by any device or device function that uses an interrupt pin. The

interrupt allocation is done by the BIOS. The POST software needs to write the routing

information to this register because it initializes and conﬁgures the system.

The value in this register speciﬁes which input of the system interrupt controller(s) the

interrupt pin of the device is connected. This value is used by device drivers and operating

systems to determine priority and vector information. Values in this register are system

architecture speciﬁc. The bit description of the register is given in Table 21.

Table 21. IL - Interrupt Line register (address 3Ch) bit description

Legend: * reset value

Bit

Symbol

Access

Value

Description

7 to 0 IL[7:0]

R/W

00h*

Interrupt Line: Indicates which IRQ is used to report

interrupt from the SAF1562HL.

8.2.1.15 Interrupt Pin register

This 1 B register is use to specify which interrupt pin the device or device function uses.

A value of 1h corresponds to INTA#, 2h corresponds to INTB#, 3h corresponds to INTC#,

and 4h corresponds to INTD#. Devices or functions that do not use interrupt pin must set

this register to logic 0. The bit description is given in Table 22.

Table 22. IP - Interrupt Pin register (address 3Dh) bit description

Legend: * reset value

Bit

Symbol

Access

Value

Description

7 to 0 IP[7:0]

R

01h*

Interrupt Pin: INTA# is the default interrupt pin used

by the SAF1562HL.

8.2.1.16 Min_Gnt and Max_Lat registers

The Minimum Grant (Min_Gnt) and Maximum Latency (Max_Lat) registers are used to

specify the desired settings of the device for latency timer values. For both registers, the

value speciﬁes a period of time in units of 250 ns. Logic 0 indicates that the device has no

major requirements for setting latency timers.

The Min_Gnt register bit description is given in Table 23.

Table 23. Min_Gnt - Minimum Grant register (address 3Eh) bit description

Legend: * reset value

Bit

Symbol

Access Value

0Xh*^[1]

Description

7 to 0 MIN_GNT

[7:0]

R

Min_Gnt: It is used to specify how long a burst period

the device needs, assuming a clock rate of 33 MHz.

[1] X is 1h for OHCI1 and OHCI2; X is 2h for EHCI.

The Max_Lat register bit description is given in Table 24.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

21 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 24. Max_Lat - Maximum Latency register (address 3Fh) bit description

Legend: * reset value

Bit Symbol

Access Value

XXh*^[1]

Description

7 to 0 MAX_LAT

[7:0]

R

Max_Lat: It is used to specify how often the device

needs to gain access to the PCI bus.

[1] XX is 2Ah for OHCI1 and OHCI2; XX is 10h for EHCI.

8.2.1.17 TRDY time-out register

This is a read and write register at address 40h. The default and recommended value is

00h—TRDY time-out disabled. This value can, however, be modiﬁed. It is an

implementation-speciﬁc register, and not a standard PCI conﬁguration register.

The TRDY timer is 13 bits—the lower 5 bits are ﬁxed as logic 0, and the upper 8 bits are

determined by the TRDY time-out register value. The time-out is calculated by multiplying

the 13-bit timer with the PCI CLK cycle time.

This register determines the maximum TRDY delay without asserting the Unrecoverable

Error (UE) bit. If TRDY is longer than the delay determined by this register value, then the

UE bit will be set.

8.2.1.18 Retry time-out register

The default value of this read and write register is 80h, and is located at address 41h. This

value can, however, be modiﬁed. Programming this register as 00h means that retry

time-out is disabled. This is an implementation-speciﬁc register, and not a standard PCI

conﬁguration register.

The time-out is determined by multiplying the register value with the PCI CLK cycle time.

This register determines the maximum number of PCI retires before the UE bit is set. If the

number of retries is longer than the delay determined by this register value, then the UE

bit will be set.

8.2.2 Enhanced Host Controller-speciﬁc PCI registers

In addition to the PCI conﬁguration header registers, EHCI needs some additional PCI

conﬁguration space registers to indicate the serial bus release number, downstream port

wake-up event capability, and adjust the USB bus frame length for Start-of-Frame (SOF).

The EHCI-speciﬁc PCI registers are given in Table 25.

Table 25. EHCI-speciﬁc PCI registers

Offset

60h

Register

Serial Bus Release Number (SBRN)

Frame Length Adjustment (FLADJ)

Port Wake Capability (PORTWAKECAP)

61h

62h and 63h

8.2.2.1 SBRN register

The Serial Bus Release Number (SBRN) register is a 1 B register, and the bit description

is given in Table 26. This register contains the release number of the USB speciﬁcation

with which this USB Host Controller module is compliant.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

22 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 26. SBRN - Serial Bus Release Number register (address 60h) bit description

Legend: * reset value

Bit

Symbol

Access Value Description

7 to 0

SBRN[7:0]

R

20h*

Serial Bus Speciﬁcation Release Number: This

register value is to identify Serial Bus Speciﬁcation

Rev. 2.0. All other combinations are reserved.

8.2.2.2 FLADJ register

This feature is used to adjust any offset from the clock source that generates the clock that

drives the SOF counter. When a new value is written to these six bits, the length of the

frame is adjusted. The bit allocation of the Frame Length Adjustment (FLADJ) register is

given in Table 27.

Table 27. FLADJ - Frame Length Adjustment register (address 61h) bit allocation

Bit

7

6

5

4

3

2

1

0

Symbol

Reset

Access

reserved^[1]

FLADJ[5:0]

0

1

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 28. FLADJ - Frame Length Adjustment register (address 61h) bit description

Bit

Symbol

Description

7 and 6

5 to 0

reserved

-

FLADJ[5:0] Frame Length Timing Value: Each decimal value change to this register

corresponds to 16 high-speed bit times. The SOF cycle time—number of

SOF counter clock periods to generate a SOF micro frame length—is

equal to 59488 + value in this ﬁeld. The default value is decimal 32 (20h),

which gives a SOF cycle time of 60000.

FLADJ value

SOF cycle time

(480 MHz)

0 (00h)

1 (01h)

2 (02h)

:

59488

59504

59520

:

31 (1Fh)

32 (20h)

:

59984

60000

:

62 (3Eh)

63 (3Fh)

60480

60496

8.2.2.3 PORTWAKECAP register

Port Wake Capability (PORTWAKECAP) is a 2 B register used to establish a policy about

which ports are for wake events; see Table 29. Bit positions 15 to 1 in the mask

correspond to a physical port implemented on the current EHCI controller. Logic 1 in a bit

position indicates that a device connected below the port can be enabled as a wake-up

device and the port may be enabled for disconnect or connect, or overcurrent events as

wake-up events. This is an information only mask register. The bits in this register do not

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

23 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

affect the actual operation of the EHCI Host Controller. The system-speciﬁc policy can be

established by BIOS initializing this register to a system-speciﬁc value. The system

software uses the information in this register when enabling devices and ports for remote

wake-up.

Table 29. PORTWAKECAP - Port Wake Capability register (address 62h) bit description

Legend: * reset value

Bit

Symbol

Access Value

Description

15 to 0 PORTWAKECAP

[15:0]

R/W

0007h*

Port Wake-Up Capability Mask: EHCI

does not implement this feature.

8.2.3 Power management registers

Table 30. Power Management registers

Offset

Register

Value read from address 34h + 0h

Value read from address 34h + 1h

Value read from address 34h + 2h

Value read from address 34h + 4h

Value read from address 34h + 6h

Capability Identiﬁer (Cap_ID)

Next Item Pointer (Next_Item_Ptr)

Power Management Capabilities (PMC)

Power Management Control/Status (PMCSR)

Power Management Control/Status PCI-to-PCI Bridge

Support Extensions (PMCSR_BSE)

Value read from address 34h + 7h

Data

8.2.3.1 Cap_ID register

The Capability Identiﬁer (Cap_ID) register when read by the system software as 01h

indicates that the data structure currently being pointed to is the PCI Power Management

data structure. Each function of a PCI device may have only one item in its capability list

with Cap_ID set to 01h. The bit description of the register is given in Table 31.

Table 31. Cap_ID - Capability Identiﬁer register bit description

Address: Value read from address 34h + 0h

Legend: * reset value

Bit

Symbol

Access Value

01h*

Description

7 to 0 CAP_ID[7:0]

R

ID: This ﬁeld when 01h identiﬁes the linked list item as

being PCI Power Management registers.

8.2.3.2 Next_Item_Ptr register

The Next Item Pointer (Next_Item_Ptr) register describes the location of the next item in

the function’s capability list. The value given is an offset into the function’s PCI

conﬁguration space. If the function does not implement any other capabilities deﬁned by

the PCI-SIG for inclusion in the capabilities list, or if power management is the last item in

the list, then this register must be set to 00h. See Table 32.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

24 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 32. Next_Item_Ptr - Next Item Pointer register bit description

Address: Value read from address 34h + 1h

Legend: * reset value

Bit

Symbol

Access Value Description

00h*

7 to 0 NEXT_ITEM_

PTR[7:0]

R

Next Item Pointer: This ﬁeld provides an offset into

the function’s PCI conﬁguration space, pointing to the

location of the next item in the function’s capability list.

If there are no additional items in the capabilities list,

this register is set to 00h.

8.2.3.3 PMC register

The Power Management Capabilities (PMC) register is a 2 B register, and the bit

allocation is given in Table 33. This register provides information on the capabilities of the

function related to power management.

Table 33. PMC - Power Management Capabilities register bit allocation

Address: Value read from address 34h + 2h

Bit

15

14

13

12

11

10

D2_S

X^[1]

R

9

8

Symbol

Reset

Access

Bit

PME_S[4:0]

D1_S

AUX_C

1

R

7

1

R

6

X^[1]

1

X^[1]

R

1

0

R

0

R

5

4

3

2

1

Symbol

Reset

Access

AUX_C[1:0]

DSI

0

reserved

PMI

0

VER[2:0]

1

0

1

0

R

[1] X = logic 0 for OHCI1 and OHCI2; X = logic 1 for EHCI.

Table 34. PMC - Power Management Capabilities register bit description

Address: Value read from address 34h + 2h

Bit

Symbol Description

15 to 11 PME_S

[4:0]

PME_Support: These bits indicate the power states in which the function

may assert PME#. Logic 0 for any bit indicates that the function is not

capable of asserting the PME# signal while in that power state.

PME_S[0] — PME# can be asserted from D0

PME_S[1] — PME# can be asserted from D1

PME_S[2] — PME# can be asserted from D2

PME_S[3] — PME# can be asserted from D3_hot

PME_S[4] — PME# can be asserted from D3_cold

10

9

D2_S

D1_S

D2_Support: If this bit is logic 1, this function supports the D2 Power

Management State. Functions that do not support D2 must always return

logic 0 for this bit.

D1_Support: If this bit is logic 1, this function supports the D1 Power

Management State. Functions that do not support D1 must always return

logic 0 for this bit.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

25 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 34. PMC - Power Management Capabilities register bit description …continued

Address: Value read from address 34h + 2h

Bit

Symbol Description

8 to 6

AUX_C

[2:0]

Aux_Current: This three-bit ﬁeld reports the V_aux(3V3)auxiliary current

requirements for the PCI function.

If the Data register is implemented by this function:

• A read from this ﬁeld needs to return a value of 000b

• The Data register takes precedence over this ﬁeld for V_aux(3V3)current

requirement reporting

If the PME# generation from D3_coldis not supported by the function

(PMC[15] = logic 0), this ﬁeld must return a value of 000b when read.

For functions that support PME# from D3_coldand do not implement the Data

register, the bit assignments corresponding to the maximum current required

for V_aux(3V3)are:

111b — 375 mA

110b — 320 mA

101b — 270 mA

100b — 220 mA

011b — 160 mA

010b — 100 mA

001b — 55 mA

000b — 0 (self powered)

5

DSI

Device Speciﬁc Initialization: This bit indicates whether special

initialization of this function is required, beyond the standard PCI

conﬁguration header, before the generic class device driver is able to use it.

This bit is not used by some operating systems. For example, Microsoft

Windows and Windows NT do not use this bit to determine whether to use

D3. Instead, it is determined using the capabilities of the driver.

Logic 1 indicates that the function requires a device-speciﬁc initialization

sequence, following transition to D0 un-initialized state.

4

3

reserved

PMI

-

PME Clock:

0 — Indicates that no PCI clock is required for the function to generate PME#

1 — Indicates that the function relies on the presence of the PCI clock for the

PME# operation

Functions that do not support the PME# generation in any state must return

logic 0 for this ﬁeld.

2 to 0

VER[2:0] Version: A value of 010b indicates that this function complies with PCI Bus

Power Management Interface Speciﬁcation Rev. 1.1.

8.2.3.4 PMCSR register

The Power Management Control/Status Register (PMCSR) is a 2 B register used to

manage the power management state of the PCI function, as well as to allow and monitor

Power Management Events (PMEs). The bit allocation of the register is given in Table 35.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

26 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 35. PMCSR - Power Management Control/Status register bit allocation

Address: Value read from address 34h + 4h

Bit

15

PMES

X^[1]

14

13

12

11

10

9

8

PMEE

X^[1]

Symbol

Reset

Access

Bit

DS[1:0]

D_S[3:0]

0

R

6

0

R

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

R/W

7

R/W

0

Symbol

Reset

Access

reserved^[2]

PS[1:0]

0

R/W

[1] Sticky bit, if the function supports PME# from D3_cold, then X is indeterminate at the time of initial operating

system boot; X is 0 if the function does not support PME# from D3_cold

.

[2] The reserved bits should always be written with the reset value.

Table 36. PMCSR - Power Management Control/Status register bit description

Address: Value read from address 34h + 4h

Bit

Symbol Description

15

PMES PME Status: This bit is set when the function normally asserts the PME#

signal independent of the state of the PMEE bit. Writing logic 1 to this bit

clears it and causes the function to stop asserting PME#, if enabled.

Writing logic 0 has no effect. This bit defaults to logic 0, if the function does

not support the PME# generation from D3_cold. If the function supports the

PME# generation from D3_cold, then this bit is sticky and must be explicitly

cleared by the operating system each time the operating system is initially

loaded.

14 and 13 DS[1:0]

Data Scale: This two-bit read-only ﬁeld indicates the scaling factor when

interpreting the value of the Data register. The value and meaning of this

ﬁeld vary, depending on which data value is selected by the D_S ﬁeld. This

ﬁeld is a required component of the Data register (offset 7) and must be

implemented, if the Data register is implemented. If the Data register is not

implemented, this ﬁeld must return 00b when PMCSR is read.

12 to 9

D_S[3:0] Data_Select: This four-bit ﬁeld selects the data that is reported through the

Data register and the D_S ﬁeld. This ﬁeld is a required component of the

Data register (offset 7) and must be implemented, if the Data register is

implemented. If the Data register is not implemented, this ﬁeld must return

00b when PMCSR is read.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

27 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 36. PMCSR - Power Management Control/Status register bit description …continued

Address: Value read from address 34h + 4h

Bit

Symbol Description

8

PMEE

PME Enabled: Logic 1 allows the function to assert PME#. When it is

logic 0, PME# assertion is disabled. This bit defaults to logic 0, if the

function does not support the PME# generation from D3_cold. If the function

supports PME# from D3_cold, then this bit is sticky and must be explicitly

cleared by the operating system each time the operating system is initially

loaded.

7 to 2

reserved

PS[1:0]

-

1 and 0

Power State: This two-bit ﬁeld is used to determine the current power state

of the EHCI function and to set the function into a new power state. The

deﬁnition of the ﬁeld values is given as:

00b — D0

01b — D1

10b — D2

11b — D3_hot

If the software attempts to write an unsupported, optional state to this ﬁeld,

the write operation must complete normally on the bus; however, the data

is discarded and no status change occurs.

8.2.3.5 PMCSR_BSE register

The PMCSR PCI-to-PCI Bridge Support Extensions (PMCSR_BSE) register supports PCI

bridge-speciﬁc functionality and is required for all PCI-to-PCI bridges. The bit allocation of

this register is given in Table 37.

Table 37. PMCSR_BSE - PMCSR PCI-to-PCI Bridge Support Extensions register bit

allocation

Address: Value read from address 34h + 6h

Bit

7

6

5

4

3

2

1

0

Symbol BPCC_EN B2_B3#

reserved

Reset

0

Access

R

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

28 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 38. PMCSR_BSE - PMCSR PCI-to-PCI Bridge Support Extensions register bit

description

Address: Value read from address 34h + 6h

Bit

Symbol

BPCC_EN Bus Power/Clock Control Enable:

1 — Indicates that the bus power or clock control mechanism as deﬁned in

Description

7

Table 39 is enabled

0 — Indicates that the bus or power control policies as deﬁned in Table 39

are disabled

When the Bus Power or Clock Control mechanism is disabled, the bridge’s

PMCSR Power State (PS) ﬁeld cannot be used by the system software to

control the power or clock of the bridge’s secondary bus.

6

B2_B3#

B2/B3 support for D3_hot: The state of this bit determines the action that is

to occur as a direct result of programming the function to D3_hot

.

1 — Indicates that when the bridge function is programmed to D3_hot, its

secondary bus’s PCI clock will be stopped (B2)

0 — Indicates that when the bridge function is programmed to D3_hot, its

secondary bus will have its power removed (B3)

This bit is only meaningful if bit 7 (BPCC_EN) is logic 1.

-

5 to 0 reserved

Table 39. PCI bus power and clock control

Originating device’s Secondary bus Resultant actions by bridge

bridge PM state

PM state

(either direct or indirect)

D0

B0

none

D1

B1

none

D2

B2

clock stopped on secondary bus

D3_hot

B2, B3

clock stopped and PCI V_CCremoved from secondary

bus (B3 only); for deﬁnition of B2_B3#, see Table 38

D3_cold

B3

none

8.2.3.6 Data register

The Data register is an optional, 1 B register that provides a mechanism for the function to

report state dependent operating data, such as power consumed or heat dissipated.

Table 40 shows the bit description of the register.

Table 40. Data register bit description

Address: Value read from address 34h + 7h

Legend: * reset value

Bit

Symbol Access Value Description

00h*

7 to 0 DATA[7:0]

R

DATA: This register is used to report the state dependent

data requested by the D_S ﬁeld of the PMCSR register.

The value of this register is scaled by the value reported by

the DS ﬁeld of the PMCSR register.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

29 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

9. I²C-bus interface

A simple I²C-bus interface is provided in the SAF1562HL to read customized vendor ID,

product ID and some other conﬁguration bits from an external EEPROM.

The I²C-bus interface is for bidirectional communication between ICs using two serial bus

wires: SDA (data) and SCL (clock). Both lines are driven by open-drain circuits and must

be connected to the positive supply voltage through pull-up resistors when in use;

otherwise, they must be connected to ground.

9.1 Protocol

The I²C-bus protocol deﬁnes the following conditions:

• Bus free: both SDA and SCL are HIGH

• START: a HIGH-to-LOW transition on SDA, while SCL is HIGH

• STOP: a LOW-to-HIGH transition on SDA, while SCL is HIGH

• Data valid: after a START condition, data on SDA is stable during the HIGH period of

SCL; data on SDA may only change while SCL is LOW

Each device on the I²C-bus has a unique slave address, which the master uses to select a

device for access.

The master starts a data transfer using a START condition and ends it by generating a

STOP condition. Transfers can only be initiated when the bus is free. The receiver must

acknowledge each byte by using a LOW level on SDA during the ninth clock pulse on

SCL.

For detailed information, refer to The I²C-bus Speciﬁcation, Version 2.1.

9.2 Hardware connections

The SAF1562HL can be connected to an external EEPROM through the I²C-bus

interface. The hardware connections are shown in Figure 5.

V

aux(3V3)

R

P

R

P

SCL

SDA

SCL

SDA

A0

A1

A2

2

I C-bus

24C01

EEPROM

or

SAF1562HL

USB HOST

equivalent

008aaa028

Fig 5. EEPROM connection diagram

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

30 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

The slave address that the SAF1562HL uses to access the EEPROM is 1010 000b. Page

mode addressing is not supported. Therefore, pins A0, A1 and A2 of the EEPROM must

be connected to ground (logic 0).

9.3 Information loading from EEPROM

Figure 6 shows the content of the EEPROM memory. If the EEPROM is not present, the

default values of Device ID, Vendor ID, subsystem VID and subsystem DID assigned to

NXP Semiconductors by PCI-SIG will be loaded. For default values, see Table 3.

address

0

1

2

3

4

5

6

7

subsystem vendor ID (L)

subsystem vendor ID (H)

subsystem device ID (L) - OHCI

subsystem device ID (H) - OHCI

subsystem device ID (L) - EHCI

subsystem device ID (H) - EHCI

reserved - FFh

15h - loads subsystem vendor ID, device ID

1Ah - loads default values defined by Philips Semiconductors

signature

004aaa124

L = LOW; H = HIGH.

Fig 6. Information loading from EEPROM

10. Power management

10.1 PCI bus power states

The PCI bus can be characterized by one of the four power management states: B0, B1,

B2 and B3.

B0 state (PCI clock = 33 MHz, PCI bus power = on) — This corresponds to the bus

being fully operational.

B1 state (PCI clock = intermittent clock operation mode, PCI bus power = on) —

When a PCI bus is in B1, PCI V_CCis still applied to all devices on the bus. No bus

transactions, however, are allowed to take place on the bus. The B1 state indicates a

perpetual idle state on the PCI bus.

B2 state (PCI clock = stop, PCI bus power = on) — PCI V_CCis still applied on the bus,

but the clock is stopped and held in the LOW state.

B3 state (PCI clock = stop, PCI bus power = off) — PCI V_CCis removed from all

devices on the PCI bus segment.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

31 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

10.2 USB bus states

Reset state — When the USB bus is in the reset state, the USB system is stopped.

Operational state — When the USB bus is in the active state, the USB system is

operating normally.

Suspend state — When the USB bus is in the suspend state, the USB system is

stopped.

Resume state — When the USB bus is in the resume state, the USB system is operating

normally.

11. USB Host Controller registers

Each Host Controller contains a set of on-chip operational registers that are mapped to

un-cached memory of the system addressable space. This memory space must begin on

a double word (32-bit) boundary. The size of the allocated space is deﬁned by the initial

value in the Base Address register 0. HCDs must interact with these registers to

implement USB functionality.

After the PCI enumeration driver ﬁnishes the PCI device conﬁguration, the new base

address of these memory-mapped operational registers is deﬁned in BAR 0. The HCD

can access these registers by using the address of base address value + offset.

Table 41 contains a list of Host Controller registers.

Table 41. USB Host Controller registers

Address OHCI register

Reset value^[1]

EHCI register

Reset value^[1]

Func0

Func1

Func2

OHCI1 (1P)

OHCI2 (1P)

EHCI (2P)

00h

04h

08h

0Ch

10h

14h

18h

1Ch

20h

24h

28h

2Ch

30h

34h

38h

3Ch

40h

44h

48h

HcRevision

0000 0010h

0000 0000h

0000 0010h

0000 0000h

0000 2EDFh

0000 0000h

0000 0628h

FF00 0901h

CAPLENGTH/HCIVERSION

HCSPARAMS

HCCPARAMS

HCSP-PORTROUTE1[31:0]

HCSP-PORTROUTE2[59:32]

reserved

0100 0020h

HcControl

0000 2192h

HcCommandStatus

HcInterruptStatus

HcInterruptEnable

HcInterruptDisable

HcHCCA

0000 0012h

0000 0010h

0000 0000h

-

reserved

-

HcPeriodCurrentED

HcControlHeadED

reserved

-

USBCMD

0008 0000h

HcControlCurrentED 0000 0000h

USBSTS

0000 1000h

HcBulkHeadED

HcBulkCurrentED

HcDoneHead

0000 0000h

0000 2EDFh

0000 0000h

0000 0628h

FF00 0901h

USBINTR

0000 0000h

FRINDEX

0000 0000h

reserved

-

HcFmInterval

PERIODICLISTBASE

ASYNCLISTADDR

reserved

0000 0000h

HcFmRemaining

HcFmNumber

0000 0000h

-

HcPeriodicStart

HcLSThreshold

HcRhDescriptorA

reserved

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

32 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 41. USB Host Controller registers …continued

Address OHCI register

Reset value^[1]

EHCI register

Reset value^[1]

Func0

Func1

Func2

OHCI1 (1P)

OHCI2 (1P)

EHCI (2P)

4Ch

50h

54h

58h

5Ch

60h

64h

68h

6Ch

70h

HcRhDescriptorB

HcRhStatus

HcRhPortStatus[1]

HcRhPortStatus[2]

reserved

0002 0000h

reserved

-

0000 0000h

reserved

-

0000 0000h

reserved

-

reserved

-

reserved

-

reserved

CONFIGFLAG

PORTSC1

PORTSC2

reserved

0000 0000h

reserved

0000 0000h

reserved

0000 0000h

reserved

-

reserved

[1] Reset values that are highlighted—for example, 0—are the SAF1562HL implementation-speciﬁc reset values; and reset values that are

not highlighted—for example, 0—are compliant with OHCI and EHCI speciﬁcations.

For the OHCI Host Controller, there are only operational registers for the USB operation.

For the Enhanced Host Controller, there are two types of registers: one set of read-only

capability registers and one set of read and write operational registers.

11.1 OHCI USB Host Controller operational registers

OHCI HCDs need to communicate with these registers to implement USB data transfers.

Based on their functions, these registers are classiﬁed into four partitions:

• Control and Status

• Memory Pointer

• Frame Counter

• Root Hub

11.1.1 HcRevision register

Table 42. HcRevision - Host Controller Revision register bit allocation

Address: Value read from func0 or func1 of address 10h + 00h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved

0

R

0

R

0

R

0

R

0

R

0

R

0

R

0

R

23

22

21

20

19

18

17

16

Symbol

Reset

Access

0

R

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

33 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

15

14

13

12

11

10

9

8

Symbol

Reset

Access

Bit

reserved

REV[7:0]

0

R

7

0

R

6

0

R

5

0

R

4

0

R

3

0

R

2

0

R

1

0

R

0

Symbol

Reset

Access

0

1

0

R

Table 43. HcRevision - Host Controller Revision register bit description

Address: Value read from func0 or func1 of address 10h + 00h

Bit

Symbol

reserved

REV[7:0]

Description

31 to 8

7 to 0

-

Revision: This read-only ﬁeld contains the BCD representation of the version of the HCI

speciﬁcation that is implemented by this Host Controller. For example, a value of 11h

corresponds to version 1.1. All of the Host Controller implementations that are compliant with this

speciﬁcation need to have a value of 10h.

11.1.2 HcControl register

This register deﬁnes the operating modes for the Host Controller. All the ﬁelds in this

register, except for HCFS and RWC, are modiﬁed only by the HCD. The bit allocation is

given in Table 44.

Table 44. HcControl - Host Controller Control register bit allocation

Address: Value read from func0 or func1 of address 10h + 04h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

19

R/W

18

R/W

17

R/W

16

20

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

10

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

12

R/W

11

13

Symbol

Reset

Access

Bit

reserved^[1]

RWE

0

RWC

0

IR

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

R/W

1

R/W

0

Symbol

Reset

Access

HCFS[1:0]

BLE

0

CLE

0

IE

PLE

0

CBSR[1:0]

0

R/W

[1] The reserved bits should always be written with the reset value.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

34 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 45. HcControl - Host Controller Control register bit description

Address: Value read from func0 or func1 of address 10h + 04h

Bit

Symbol Description

31 to 11

10

reserved

RWE

-

Remote Wakeup Enable: This bit is used by the HCD to enable or disable

the remote wake-up feature on detecting upstream resume signaling.

When this bit and RD (bit 3) in the HcInterruptStatus register are set, a

remote wake-up is signaled to the host system. Setting this bit has no

impact on the generation of hardware interrupt.

9

RWC

Remote Wakeup Connected: This bit indicates whether the Host

Controller supports remote wake-up signaling. If remote wake-up is

supported and used by the system, it is the responsibility of the system

ﬁrmware to set this bit during POST. The Host Controller clears the bit on

a hardware reset but does not alter it on a software reset. Remote

wake-up signaling of the host system is host-bus-speciﬁc and is not

described in this speciﬁcation.

8

IR

Interrupt Routing: This bit determines the routing of interrupts generated

by events registered in HcInterruptStatus. If clear, all interrupts are routed

to the normal host bus interrupt mechanism. If set, interrupts are routed to

the System Management Interrupt. The HCD clears this bit on a hardware

reset, but it does not alter this bit on a software reset. The HCD uses this

bit as a tag to indicate the ownership of the Host Controller.

7 and 6

HCFS

[1:0]

Host Controller Functional State for USB:

00b — USBRESET

01b — USBRESUME

10b — USBOPERATIONAL

11b — USBSUSPEND

A transition to USBOPERATIONAL from another state causes SOF

generation to begin 1 ms later. The HCD may determine whether the Host

Controller has begun sending SOFs by reading SF (bit 2) in

HcInterruptStatus.

This ﬁeld may be changed by the Host Controller only when in the

USBSUSPEND state. The Host Controller may move from the

USBSUSPEND state to the USBRESUME state after detecting the

resume signaling from a downstream port.

The Host Controller enters USBSUSPEND after a software reset; it enters

USBRESET after a hardware reset. The latter also resets the Root Hub

and asserts subsequent reset signaling to downstream ports.

5

BLE

Bulk List Enable: This bit is set to enable the processing of the bulk list in

the next frame. If cleared by the HCD, processing of the bulk list does not

occur after the next SOF. The Host Controller checks this bit whenever it

wants to process the list. When disabled, the HCD may modify the list. If

HcBulkCurrentED is pointing to an Endpoint Descriptor (ED) to be

removed, the HCD must advance the pointer by updating

HcBulkCurrentED before re-enabling processing of the list.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

35 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 45. HcControl - Host Controller Control register bit description …continued

Address: Value read from func0 or func1 of address 10h + 04h

Bit

Symbol Description

4

CLE Control List Enable: This bit is set to enable the processing of the control

list in the next frame. If cleared by the HCD, processing of the control list

does not occur after the next SOF. The Host Controller must check this bit

whenever it wants to process the list. When disabled, the HCD may modify

the list. If HcControlCurrentED is pointing to an ED to be removed, the

HCD must advance the pointer by updating HcControlCurrentED before

re-enabling processing of the list.

3

IE

Isochronous Enable: This bit is used by the HCD to enable or disable

processing of isochronous EDs. While processing the periodic list in a

frame, the Host Controller checks the status of this bit when it ﬁnds an

isochronous ED (F = logic 1). If set (enabled), the Host Controller

continues processing the EDs. If cleared (disabled), the Host Controller

halts processing of the periodic list—which now contains only isochronous

EDs—and begins processing the bulk or control lists. Setting this bit is

guaranteed to take effect in the next frame and not the current frame.

2

PLE

Periodic List Enable: This bit is set to enable the processing of the

periodic list in the next frame. If cleared by the HCD, processing of the

periodic list does not occur after the next SOF. The Host Controller must

check this bit before it starts processing the list.

1 and 0

CBSR

[1:0]

Control Bulk Service Ratio: This speciﬁes the service ratio of control

EDs over bulk EDs. Before processing any of the nonperiodic lists, the

Host Controller must compare the ratio speciﬁed with its internal count on

how many nonempty control EDs are processed, in determining whether

to continue serving another control ED or switching to bulk EDs. The

internal count must be retained when crossing the frame boundary. After a

reset, the HCD is responsible to restore this value.

00b — 1 : 1

01b — 2 : 1

10b — 3 : 1

11b — 4 : 1

11.1.3 HcCommandStatus register

The HcCommandStatus register is used by the Host Controller to receive commands

issued by the HCD. It also reﬂects the current status of the Host Controller. To the HCD, it

appears as a ‘write to set’ register. The Host Controller must ensure that bits written as

logic 1 become set in the register while bits written as logic 0 remain unchanged in the

register. The HCD may issue multiple distinct commands to the Host Controller without

concern for corrupting previously issued commands. The HCD has normal read access to

all bits.

The SOC[1:0] ﬁeld (bit 17 and bit 16 in the HcCommandStatus register) indicates the

number of frames with which the Host Controller has detected the scheduling overrun

error. This occurs when the periodic list does not complete before EOF. When a

scheduling overrun error is detected, the Host Controller increments the counter and sets

SO (bit 0 in the HcInterruptStatus register).

Table 46 shows the bit allocation of the HcCommandStatus register.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

36 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 46. HcCommandStatus - Host Controller Command Status register bit allocation

Address: Value read from func0 or func1 of address 10h + 08h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

SOC[1:0]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol

Reset

Access

reserved^[1]

OCR

0

BLF

0

CLF

0

HCR

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 47. HcCommandStatus - Host Controller Command Status register bit description

Address: Value read from func0 or func1 of address 10h + 08h

Bit

Symbol

Description

31 to 18

reserved

-

17 and 16 SOC[1:0] Scheduling Overrun Count: The bit is incremented on each scheduling

overrun error. It is initialized to 00b and wraps around at 11b. It must be

incremented when a scheduling overrun is detected, even if SO (bit 0 in

HcInterruptStatus) is already set. This is used by the HCD to monitor any

persistent scheduling problems.

15 to 4

3

reserved

OCR

-

Ownership Change Request: This bit is set by an OS HCD to request a

change of control of the Host Controller. When set, the Host Controller

must set OC (bit 30 in HcInterruptStatus). After the changeover, this bit is

cleared and remains so until the next request from the OS HCD.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

37 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 47. HcCommandStatus - Host Controller Command Status register bit description

…continued

Bit

Symbol

Description

2

BLF

Bulk List Filled: This bit is used to indicate whether there are any

Transfer Descriptors (TDs) on the bulk list. It is set by the HCD whenever

it adds a TD to an ED in the bulk list. When the Host Controller begins to

process the head of the bulk list, it checks Bulk-Filled (BF). If BLF is

logic 0, the Host Controller does not need to process the bulk list. If BLF

is logic 1, the Host Controller needs to start processing the bulk list and

set BF to logic 0. If the Host Controller ﬁnds a TD on the list, then the

Host Controller needs to set BLF to logic 1, causing the bulk list

processing to continue. If no TD is found on the bulk list, and if the HCD

does not set BLF, then BLF is still logic 0 when the Host Controller

completes processing the bulk list and the bulk list processing stops.

1

CLF

Control List Filled: This bit is used to indicate whether there are any

TDs on the control list. It is set by the HCD whenever it adds a TD to an

ED in the control list.

When the Host Controller begins to process the head of the control list, it

checks CLF. If CLF is logic 0, the Host Controller does not need to

process the control list. If Control-Filled (CF) is logic 1, the Host

Controller needs to start processing the control list and set CLF to

logic 0. If the Host Controller ﬁnds a TD on the list, then the Host

Controller needs to set CLF to logic 1, causing the control list processing

to continue. If no TD is found on the control list, and if the HCD does not

set CLF, then CLF is still logic 0 when the Host Controller completes

processing the control list and the control list processing stops.

0

HCR

Host Controller Reset: This bit is set by the HCD to initiate a software

reset of the Host Controller. Regardless of the functional state of the Host

Controller, it moves to the USBSUSPEND state in which most of the

operational registers are reset, except those stated otherwise; for

example, IR (bit 8) in the HcControl register, and no host bus accesses

are allowed. This bit is cleared by the Host Controller on completing the

reset operation. The reset operation must be completed within 10 µs.

This bit, when set, should not cause a reset to the Root Hub and no

subsequent reset signaling should be asserted to its downstream ports.

11.1.4 HcInterruptStatus register

This is a 4 B register that provides the status of the events that cause hardware interrupts.

The bit allocation of the register is given in Table 48. When an event occurs, the Host

Controller sets the corresponding bit in this register. When a bit becomes set, a hardware

interrupt is generated, if the interrupt is enabled in the HcInterruptEnable register (see

Table 50) and the MIE (MasterInterruptEnable) bit is set. The HCD may clear speciﬁc bits

in this register by writing logic 1 to the bit positions to be cleared. The HCD may not set

any of these bits. The Host Controller does not clear the bit.

Table 48. HcInterruptStatus - Host Controller Interrupt Status register bit allocation

Address: Value read from func0 or func1 of address 10h + 0Ch

Bit

31

30

OC

0

29

28

27

26

25

24

Symbol reserved^[1]

reserved^[1]

Reset

0

Access

R/W

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

38 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

23

22

21

20

19

18

17

16

Symbol

reserved^[1]

Reset

Access

Bit

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

10

12

11

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol reserved^[1]RHSC

FNO

0

UE

0

RD

0

SF

0

WDH

0

SO

0

Reset

0

Access

R/W

[1] The reserved bits should always be written with the reset value.

Table 49. HcInterruptStatus - Host Controller Interrupt Status register bit description

Address: Value read from func0 or func1 of address 10h + 0Ch

Bit

31

30

Symbol

reserved

OC

Description

-

Ownership Change: This bit is set by the Host Controller when HCD sets

OCR (bit 3) in the HcCommandStatus register. This event, when

unmasked, will always immediately generate a System Management

Interrupt (SMI). This bit is forced to logic 0 when the SMI# pin is not

implemented.

29 to 7 reserved

-

6

RHSC

Root Hub Status Change: This bit is set when the content of HcRhStatus

or the content of any of HcRhPortStatus[NumberofDownstreamPort] has

changed.

5

4

FNO

UE

Frame Number Overﬂow: This bit is set when the MSB of HcFmNumber

(bit 15) changes value, or after the HccaFrameNumber is updated.

Unrecoverable Error: This bit is set when the Host Controller detects a

system error not related to USB. The Host Controller should not proceed

with any processing nor signaling before the system error is corrected. The

HCD clears this bit after the Host Controller is reset.

3

RD

Resume Detected: This bit is set when the Host Controller detects that a

device on the USB is asserting resume signaling. This bit is set by the

transition from no resume signaling to resume signaling. This bit is not set

when the HCD sets the USBRESUME state.

2

1

SF

Start-of-Frame: At the start of each frame, this bit is set by the Host

Controller and an SOF token is generated at the same time.

WDH

Writeback Done Head: This bit is immediately set after the Host Controller

has written HcDoneHead to HccaDoneHead. Further, updates of

HccaDoneHead occur only after this bit is cleared. The HCD should only

clear this bit after it has saved the content of HccaDoneHead.

0

SO

Scheduling Overrun: This bit is set when USB schedules for current frame

overruns and after the update of HccaFrameNumber. A scheduling overrun

increments the SOC[1:0] ﬁeld (bit 17 and bit 16 of HcCommandStatus).

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

39 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.1.5 HcInterruptEnable register

Each enable bit in the HcInterruptEnable register corresponds to an associated interrupt

bit in the HcInterruptStatus register. The HcInterruptEnable register is used to control

which events generate a hardware interrupt. A hardware interrupt is requested on the host

bus if the following conditions occur:

• A bit is set in the HcInterruptStatus register

• The corresponding bit in the HcInterruptEnable register is set

• The MIE (MasterInterruptEnable) bit is set

Writing logic 1 to a bit in this register sets the corresponding bit, whereas writing logic 0 to

a bit in this register leaves the corresponding bit unchanged. On a read, the current value

of this register is returned. The bit allocation is given in Table 50.

Table 50. HcInterruptEnable - Host Controller Interrupt Enable register bit allocation

Address: Value read from func0 or func1 of address 10h + 10h

Bit

31

MIE

0

30

OC

0

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol reserved^[1]RHSC

FNO

0

UE

0

RD

0

SF

0

WDH

0

SO

0

Reset

0

Access

R/W

[1] The reserved bits should always be written with the reset value.

Table 51. HcInterruptEnable - Host Controller Interrupt Enable register bit description

Address: Value read from func0 or func1 of address 10h + 10h

Bit

Symbol

Description

31

MIE

Master Interrupt Enable:

0 — Ignore

1 — Enables interrupt generation by events speciﬁed in other bits of this

register

30

OC

Ownership Change:

0 — Ignore

1 — Enables interrupt generation because of Ownership Change

29 to 7

reserved

-

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

40 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 51. HcInterruptEnable - Host Controller Interrupt Enable register bit description

…continued

Bit

Symbol

Description

6

RHSC

Root Hub Status Change:

0 — Ignore

1 — Enables interrupt generation because of Root Hub Status Change

5

4

3

2

1

0

FNO

UE

Frame Number Overﬂow:

0 — Ignore

1 — Enables interrupt generation because of Frame Number Overﬂow

Unrecoverable Error:

0 — Ignore

1 — Enables interrupt generation because of Unrecoverable Error

RD

Resume Detect:

0 — Ignore

1 — Enables interrupt generation because of Resume Detect

SF

Start-of-Frame:

0 — Ignore

1 — Enables interrupt generation because of Start-of-Frame

HcDoneHead Writeback:

WDH

SO

0 — Ignore

1 — Enables interrupt generation because of HcDoneHead Writeback

Scheduling Overrun:

0 — Ignore

1 — Enables interrupt generation because of Scheduling Overrun

11.1.6 HcInterruptDisable register

Each disable bit in the HcInterruptDisable register corresponds to an associated interrupt

bit in the HcInterruptStatus register. The HcInterruptDisable register is coupled with the

HcInterruptEnable register. Therefore, writing logic 1 to a bit in this register clears the

corresponding bit in the HcInterruptEnable register, whereas writing logic 0 to a bit in this

register leaves the corresponding bit in the HcInterruptEnable register unchanged. On a

read, the current value of the HcInterruptEnable register is returned.

The register contains 4 B, and the bit allocation is given in Table 52.

Table 52. HcInterruptDisable - Host Controller Interrupt Disable register bit allocation

Address: Value read from func0 or func1 of address 10h + 14h

Bit

31

MIE

0

30

OC

0

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

reserved^[1]

0

R/W

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

41 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

15

14

13

12

11

10

9

8

Symbol

reserved^[1]

Reset

Access

Bit

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

2

0

R/W

1

0

R/W

0

R/W

4

R/W

3

Symbol reserved^[1]RHSC

FNO

0

UE

0

RD

0

SF

0

WDH

0

SO

0

Reset

0

Access

R/W

[1] The reserved bits should always be written with the reset value.

Table 53. HcInterruptDisable - Host Controller Interrupt Disable register bit description

Address: Value read from func0 or func1 of address 10h + 14h

Bit

Symbol

Description

31

MIE

Master Interrupt Enable:

0 — Ignore

1 — Disables interrupt generation because of events speciﬁed in other

bits of this register

This ﬁeld is set after a hardware or software reset. Interrupts are

disabled.

30

OC

Ownership Change:

0 — Ignore

1 — Disables interrupt generation because of Ownership Change

29 to 7

6

reserved

RHSC

-

Root Hub Status Change:

0 — Ignore

1 — Disables interrupt generation because of Root Hub Status Change

5

4

3

2

1

0

FNO

UE

Frame Number Overﬂow:

0 — Ignore

1 — Disables interrupt generation because of Frame Number Overﬂow

Unrecoverable Error:

0 — Ignore

1 — Disables interrupt generation because of Unrecoverable Error

RD

Resume Detect:

0 — Ignore

1 — Disables interrupt generation because of Resume Detect

SF

Start-of-Frame:

0 — Ignore

1 — Disables interrupt generation because of Start-of-Frame

HcDoneHead Writeback:

WDH

SO

0 — Ignore

1 — Disables interrupt generation because of HcDoneHead Writeback

Scheduling Overrun:

0 — Ignore

1 — Disables interrupt generation because of Scheduling Overrun

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

42 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.1.7 HcHCCA register

The HcHCCA register contains the physical address of the Host Controller

Communication Area (HCCA). The bit allocation is given in Table 54. The HCD

determines the alignment restrictions by writing all ones to HcHCCA and reading the

content of HcHCCA. The alignment is evaluated by examining the number of zeroes in the

lower order bits. The minimum alignment is 256 B; therefore, bits 0 through 7 will always

return logic 0 when read. This area is used to hold the control structures and the interrupt

table that are accessed by both the Host Controller and the HCD.

Table 54. HcHCCA - Host Controller Communication Area register bit allocation

Address: Value read from func0 or func1 of address 10h + 18h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

HCCA[23:16]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

HCCA[15:8]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

HCCA[7:0]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol

Reset

Access

reserved^[1]

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 55. HcHCCA - Host Controller Communication Area register bit description

Address: Value read from func0 or func1 of address 10h + 18h

Bit

Symbol

Description

31 to 8

HCCA[23:0]

Host Controller Communication Area Base Address: This is the

base address of the HCCA.

7 to 0

reserved

-

11.1.8 HcPeriodCurrentED register

The HcPeriodCurrentED register contains the physical address of the current isochronous

or interrupt ED. Table 56 shows the bit allocation of the register.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

43 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 56. HcPeriodCurrentED - Host Controller Period Current Endpoint Descriptor register

bit allocation

Address: Value read from func0 or func1 of address 10h + 1Ch

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

PCED[27:20]

0

R

0

R

0

R

0

R

0

R

0

R

0

R

0

R

23

22

21

20

19

18

17

16

Symbol

Reset

Access

Bit

PCED[19:12]

0

R

0

R

0

R

0

R

0

R

0

R

0

R

9

0

R

8

15

14

13

12

11

10

Symbol

Reset

Access

Bit

PCED[11:4]

0

R

7

0

R

6

0

R

5

0

R

4

0

R

3

0

R

2

0

R

1

0

R

0

Symbol

Reset

Access

PCED[3:0]

reserved

0

R

Table 57. HcPeriodCurrentED - Host Controller Period Current Endpoint Descriptor register

bit description

Address: Value read from func0 or func1 of address 10h + 1Ch

Bit

Symbol

Description

31 to 4

PCED[27:0]

Period Current ED: This is used by the Host Controller to point to the

head of one of the periodic lists that must be processed in the current

frame. The content of this register is updated by the Host Controller

after a periodic ED is processed. The HCD may read the content in

determining which ED is being processed at the time of reading.

3 to 0

reserved

-

11.1.9 HcControlHeadED register

The HcControlHeadED register contains the physical address of the ﬁrst ED of the control

list. The bit allocation is given in Table 58.

Table 58. HcControlHeadED - Host Controller Control Head Endpoint Descriptor register bit

allocation

Address: Value read from func0 or func1 of address 10h + 20h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

CHED[27:20]

0

R

0

R

0

R

0

R

0

R

0

R

0

R

0

R

23

22

21

20

19

18

17

16

Symbol

Reset

Access

CHED[19:12]

0

R

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

44 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

15

14

13

12

11

10

9

8

Symbol

CHED[11:4]

Reset

Access

Bit

0

R

7

0

R

6

0

R

5

0

R

4

0

R

3

0

R

2

0

R

1

0

R

0

Symbol

Reset

Access

CHED[3:0]

reserved

0

R

Table 59. HcControlHeadED - Host Controller Control Head Endpoint Descriptor register bit

description

Address: Value read from func0 or func1 of address 10h + 20h

Bit

Symbol

Description

31 to 4 CHED[27:0] Control Head ED: The Host Controller traverses the control list, starting

with the HcControlHeadED pointer. The content is loaded from HCCA

during the initialization of the Host Controller.

3 to 0

reserved

-

11.1.10 HcControlCurrentED register

The HcControlCurrentED register contains the physical address of the current ED of the

control list. The bit allocation is given in Table 60.

Table 60. HcControlCurrentED - Host Controller Control Current Endpoint Descriptor

register bit allocation

Address: Value read from func0 or func1 of address 10h + 24h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

CCED[27:20]

0

R

0

R

0

R

0

R

0

R

0

R

0

R

0

R

23

22

21

20

19

18

17

16

Symbol

Reset

Access

Bit

CCED[19:12]

0

R

0

R

0

R

0

R

0

R

0

R

0

R

9

0

R

8

15

14

13

12

11

10

Symbol

Reset

Access

Bit

CCED[11:4]

0

R

7

0

R

6

0

R

5

0

R

4

0

R

3

0

R

2

0

R

1

0

R

0

Symbol

Reset

Access

CCED[3:0]

reserved

0

R

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

45 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 61. HcControlCurrentED - Host Controller Control Current Endpoint Descriptor

register bit description

Address: Value read from func0 or func1 of address 10h + 24h

Bit

Symbol

Description

31 to 4 CCED[27:0] Control Current ED: This pointer is advanced to the next ED after serving

the present. The Host Controller must continue processing the list from

where it left off in the last frame. When it reaches the end of the control list,

the Host Controller checks CLF (bit 1 of HcCommandStatus). If set, it

copies the content of HcControlHeadED to HcControlCurrentED and

clears the bit. If not set, it does nothing. The HCD is allowed to modify this

register only when CLE (bit 4 in the HcControl register) is cleared. When

set, the HCD only reads the instantaneous value of this register. Initially,

this is set to logic 0 to indicate the end of the control list.

3 to 0

reserved

-

11.1.11 HcBulkHeadED register

This register (see Table 62) contains the physical address of the ﬁrst ED of the bulk list.

Table 62. HcBulkHeadED - Host Controller Bulk Head Endpoint Descriptor register bit

allocation

Address: Value read from func0 or func1 of address 10h + 28h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

BHED[27:20]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

BHED[19:12]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

BHED[11:4]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol

Reset

Access

BHED[3:0]

reserved^[1]

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 63. HcBulkHeadED - Host Controller Bulk Head Endpoint Descriptor register bit

description

Address: Value read from func0 or func1 of address 10h + 28h

Bit

Symbol

Description

31 to 4

BHED[27:0] Bulk Head ED: The Host Controller traverses the bulk list starting

with the HcBulkHeadED pointer. The content is loaded from HCCA

during the initialization of the Host Controller.

3 to 0

reserved

-

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

46 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.1.12 HcBulkCurrentED register

This register contains the physical address of the current endpoint of the bulk list. The

endpoints are ordered according to their insertion to the list because the bulk list must be

served in a round-robin fashion. The bit allocation is given in Table 64.

Table 64. HcBulkCurrentED - Host Controller Bulk Current Endpoint Descriptor register bit

allocation

Address: Value read from func0 or func1 of address 10h + 2Ch

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

BCED[27:20]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

BCED[19:12]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

BCED[11:4]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol

Reset

Access

BCED[3:0]

reserved^[1]

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 65. HcBulkCurrentED - Host Controller Bulk Current Endpoint Descriptor register bit

description

Address: Value read from func0 or func1 of address 10h + 2Ch

Bit

Symbol

Description

31 to 4 BCED[27:0] Bulk Current ED: This is advanced to the next ED after the Host

Controller has served the current ED. The Host Controller continues

processing the list from where it left off in the last frame. When it reaches

the end of the bulk list, the Host Controller checks CLF (bit 1 of

HcCommandStatus). If the CLF bit is not set, nothing is done. If the CLF

bit is set, it copies the content of HcBulkHeadED to HcBulkCurrentED and

clears the CLF bit. The HCD can modify this register only when BLE (bit 5

in the HcControl register) is cleared. When HcControl is set, the HCD

reads the instantaneous value of this register. This is initially set to logic 0

to indicate the end of the bulk list.

3 to 0 reserved

-

11.1.13 HcDoneHead register

The HcDoneHead register contains the physical address of the last completed TD that

was added to the Done queue. In normal operation, the HCD need not read this register

because its content is periodically written to the HCCA. Table 66 contains the bit allocation

of the register.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

47 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 66. HcDoneHead - Host Controller Done Head register bit allocation

Address: Value read from func0 or func1 of address 10h + 30h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

DH[27:20]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

DH[19:12]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

DH[11:4]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol

Reset

Access

DH[3:0]

reserved^[1]

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 67. HcDoneHead - Host Controller Done Head register bit description

Address: Value read from func0 or func1 of address 10h + 30h

Bit

Symbol

Description

31 to 4

DH[27:0]

Done Head: When a TD is completed, the Host Controller writes the

content of HcDoneHead to the NextTD ﬁeld of the TD. The Host

Controller then overwrites the content of HcDoneHead with the

address of this TD. This is set to logic 0 whenever the Host Controller

writes the content of this register to HCCA.

3 to 0

reserved

-

11.1.14 HcFmInterval register

This register contains a 14-bit value that indicates the bit time interval in a frame—that is,

between two consecutive SOFs—and a 15-bit value indicating the full-speed maximum

packet size that the Host Controller may transmit or receive, without causing a scheduling

overrun. The HCD may carry out minor adjustment on FI (Frame Interval) by writing a new

value over the present at each SOF. This provides the possibility for the Host Controller to

synchronize with an external clocking resource and to adjust any unknown local clock

offset. The bit allocation of the register is given in Table 68.

Table 68. HcFmInterval - Host Controller Frame Interval register bit allocation

Address: Value read from func0 or func1 of address 10h + 34h

Bit

31

FIT

0

30

29

28

27

26

25

24

Symbol

Reset

Access

FSMPS[14:8]

0

R/W

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

48 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

23

22

21

20

19

18

17

16

Symbol

FSMPS[7:0]

Reset

Access

Bit

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

reserved^[1]

FI[13:8]

0

R/W

7

0

R/W

6

1

R/W

5

0

R/W

4

1

R/W

3

1

R/W

2

1

R/W

1

0

R/W

0

Symbol

Reset

Access

FI[7:0]

1

0

1

R/W

[1] The reserved bits should always be written with the reset value.

Table 69. HcFmInterval - Host Controller Frame Interval register bit description

Address: Value read from func0 or func1 of address 10h + 34h

Bit

Symbol

Description

31

FIT

Frame Interval Toggle: The HCD toggles this bit whenever it loads a

new value to Frame Interval.

30 to 16

FSMPS[14:0] FS Largest Data Packet: This ﬁeld speciﬁes the value that is loaded

into the largest data packet counter at the beginning of each frame.

The counter value represents the largest amount of data in bits that

can be sent or received by the Host Controller in a single transaction at

any given time, without causing a scheduling overrun. The ﬁeld value

is calculated by the HCD.

15 and 14 reserved

13 to 0 FI[13:0]

-

Frame Interval: This speciﬁes the interval between two consecutive

SOFs in bit times. The nominal value is set to 11,999. The HCD should

store the current value of this ﬁeld before resetting the Host Controller

to reset this ﬁeld to its nominal value. The HCD can then restore the

stored value on completing the reset sequence.

11.1.15 HcFmRemaining register

This register is a 14-bit down counter showing the bit time remaining in the current frame.

Table 70 contains the bit allocation of this register.

Table 70. HcFmRemaining - Host Controller Frame Remaining register bit allocation

Address: Value read from func0 or func1 of address 10h + 38h

Bit

31

FRT

0

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

reserved^[1]

0

R/W

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

49 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

15

14

13

12

11

10

9

8

Symbol

reserved^[1]

FR[13:8]

Reset

Access

Bit

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

2

0

R/W

1

0

R/W

0

R/W

3

Symbol

Reset

Access

FR[7:0]

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 71. HcFmRemaining - Host Controller Frame Remaining register bit description

Address: Value read from func0 or func1 of address 10h + 38h

Bit

Symbol

Description

31

FRT

Frame Remaining Toggle: This bit is loaded from FIT (bit 31 of

HcFmInterval) whenever FR[13:0] reaches 0. This bit is used by the HCD

for the synchronization between FI[13:0] (bit 13 to bit 0 of HcFmInterval)

and FR[13:0].

30 to 14 reserved

13 to 0

-

FR[13:0] Frame Remaining: This counter is decremented at each bit time. When it

reaches 0, it is reset by loading the FI[13:0] value speciﬁed in HcFmInterval

at the next bit time boundary. When entering the USBOPERATIONAL state,

the Host Controller reloads the content with FI[13:0] of HcFmInterval and

uses the updated value from the next SOF.

11.1.16 HcFmNumber register

This register is a 16-bit counter, and the bit allocation is given in Table 72. It provides a

timing reference among events happening in the Host Controller and the HCD. The HCD

may use the 16-bit value speciﬁed in this register and generate a 32-bit frame number,

without requiring frequent access to the register.

Table 72. HcFmNumber - Host Controller Frame Number register bit allocation

Address: Value read from func0 or func1 of address 10h + 3Ch

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

reserved^[1]

FN[13:8]

0

R/W

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

50 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

7

6

5

4

3

2

1

0

Symbol

FN[7:0]

Reset

0

Access

R/W

[1] The reserved bits should always be written with the reset value.

Table 73. HcFmNumber - Host Controller Frame Number register bit description

Address: Value read from func0 or func1 of address 10h + 3Ch

Bit

Symbol

reserved

FN[13:0]

Description

31 to 14

13 to 0

-

Frame Number: Incremented when HcFmRemaining is reloaded. It

must be rolled over to 0h after FFFFh. Automatically incremented

when entering the USBOPERATIONAL state. The content is written to

HCCA after the Host Controller has incremented Frame Number at

each frame boundary and sent an SOF but before the Host Controller

reads the ﬁrst ED in that frame. After writing to HCCA, the Host

Controller sets SF (bit 2 in HcInterruptStatus).

11.1.17 HcPeriodicStart register

This register has a 14-bit programmable value that determines when is the earliest time

for the Host Controller to start processing the periodic list. For bit allocation, see Table 74.

Table 74. HcPeriodicStart - Host Controller Periodic Start register bit allocation

Address: Value read from func0 or func1 of address 10h + 40h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

reserved^[1]

P_S[13:8]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol

Reset

Access

P_S[7:0]

0

R/W

[1] The reserved bits should always be written with the reset value.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

51 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 75. HcPeriodicStart - Host Controller Periodic Start register bit description

Address: Value read from func0 or func1 of address 10h + 40h

Bit

Symbol

Description

31 to 14

13 to 0

reserved

-

P_S[13:0] Periodic Start: After a hardware reset, this ﬁeld is cleared. It is then set

by the HCD during the Host Controller initialization. The value is roughly

calculated as 10 % of HcFmInterval. A typical value is 3E67h. When

HcFmRemaining reaches the value speciﬁed, processing of the periodic

lists have priority over control or bulk processing. The Host Controller,

therefore, starts processing the interrupt list after completing the current

control or bulk transaction that is in progress.

11.1.18 HcLSThreshold register

This register contains an 11-bit value used by the Host Controller to determine whether to

commit to the transfer of a maximum of 8 B low-speed packet before EOF. Neither the

Host Controller nor the HCD can change this value. For bit allocation, see Table 76.

Table 76. HcLSThreshold - Host Controller LS Threshold register bit allocation

Address: Value read from func0 or func1 of address 10h + 44h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

reserved^[1]

LST[11:8]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

1

R/W

2

1

R/W

1

0

R/W

0

Symbol

Reset

Access

LST[7:0]

0

1

0

1

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 77. HcLSThreshold - Host Controller LS Threshold register bit description

Address: Value read from func0 or func1 of address 10h + 44h

Bit

31 to 12 reserved

11 to 0

Symbol

Description

-

LST[11:0] LS Threshold: This ﬁeld contains a value that is compared to the FR[13:0]

ﬁeld, before initiating a low-speed transaction. The transaction is started

only if FR ≥ this ﬁeld. The value is calculated by the HCD, considering the

transmission and setup overhead.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

52 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.1.19 HcRhDescriptorA register

This register is the ﬁrst of two registers describing the characteristics of the Root Hub.

Reset values are implementation-speciﬁc.

Table 78 contains the bit allocation of the HcRhDescriptorA register.

Table 78. HcRhDescriptorA - Host Controller Root Hub Descriptor A register bit allocation

Address: Value read from func0 or func1 of address 10h + 48h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

POTPGT[7:0]

1

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

12

0

R/W

11

0

R/W

10

DT

0

R/W

9

0

R/W

8

R/W

15

R/W

13

14

Symbol

Reset

Access

Bit

reserved^[1]

NOCP

0

OCPM

1

NPS

0

PSM

1

0

R/W

7

0

R/W

6

0

R/W

5

R/W

4

R/W

3

R

R/W

1

R/W

0

2

Symbol

Reset

Access

NDP[7:0]

0

1

R

[1] The reserved bits should always be written with the reset value.

Table 79. HcRhDescriptorA - Host Controller Root Hub Descriptor A register bit

description

Address: Value read from func0 or func1 of address 10h + 48h

Bit

Symbol

Description

31 to 24 POTPGT Power On To Power Good Time: This byte speciﬁes the duration the HCD

[7:0]

must wait before accessing a powered-on port of the Root Hub. It is

implementation-speciﬁc. The unit of time is 2 ms. The duration is calculated

as POTPGT × 2 ms.

23 to 13 reserved

-

12

NOCP

No Over Current Protection: This bit describes how the overcurrent status

for Root Hub ports are reported. When this bit is cleared, the OCPM bit

speciﬁes global or per-port reporting.

0 — Overcurrent status is collectively reported for all downstream ports

1 — No overcurrent protection supported

11

OCPM

Over Current Protection Mode: This bit describes how the overcurrent

status for Root Hub ports are reported. At reset, this ﬁelds reﬂects the same

mode as Power Switching Mode. This ﬁeld is valid only if the NOCP bit is

cleared.

0 — Overcurrent status is collectively reported for all downstream ports

1 — Overcurrent status is reported on a per-port basis

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

53 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 79. HcRhDescriptorA - Host Controller Root Hub Descriptor A register bit description

…continued

Address: Value read from func0 or func1 of address 10h + 48h

Bit

Symbol

Description

10

DT

Device Type: This bit speciﬁes that the Root Hub is not a compound

device. The Root Hub is not permitted to be a compound device. This ﬁeld

should always read logic 0.

9

8

NPS

PSM

No Power Switching: This bit is used to specify whether power switching is

supported or ports are always powered. It is implementation-speciﬁc. When

this bit is cleared, the PSM bit speciﬁes global or per-port switching.

0 — Ports are power switched

1 — Ports are always powered on when the Host Controller is powered on

Power Switching Mode: This bit is used to specify how the power

switching of Root Hub ports is controlled. It is implementation-speciﬁc. This

ﬁeld is only valid if the NPS ﬁeld is cleared.

0 — All ports are powered at the same time

1 — Each port is individually powered. This mode allows port power to be

controlled by either the global switch or per-port switching. If the PPCM

(Port Power Control Mask) bit is set, the port responds only to port power

commands (Set/Clear Port Power). If the port mask is cleared, then the port

is controlled only by the global power switch (Set/Clear Global Power).

7 to 0

NDP[7:0] Number Downstream Ports: These bits specify the number of

downstream ports supported by the Root Hub. It is implementation-speciﬁc.

The minimum number of ports is 1. The maximum number of ports

supported by OHCI is 15.

11.1.20 HcRhDescriptorB register

The HcRhDescriptorB register is the second of two registers describing the characteristics

of the Root Hub. The bit allocation is given in Table 80. These ﬁelds are written during

initialization to correspond to the system implementation. Reset values are

implementation-speciﬁc.

Table 80. HcRhDescriptorB - Host Controller Root Hub Descriptor B register bit allocation

Address: Value read from func0 or func1 of address 10h + 4Ch

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

PPCM[15:0]

0

R

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

18

R/W

17

R/W

16

19

Symbol

Reset

Access

Bit

PPCM[7:0]

0

1

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

DR[15:8]

0

R/W

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

54 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

7

6

5

4

3

2

1

0

Symbol

DR[7:0]

Reset

0

Access

R/W

Table 81. HcRhDescriptorB - Host Controller Root Hub Descriptor B register bit

description

Address: Value read from func0 or func1 of address 10h + 4Ch

Bit

Symbol Description

31 to 16 PPCM

[15:0]

Port Power Control Mask: Each bit indicates whether a port is affected by a

global power control command when Power Switching Mode is set. When

set, only the power state of the port is affected by per-port power control

(Set/Clear Port Power). When cleared, the port is controlled by the global

power switch (Set/Clear Global Power). If the device is conﬁgured to global

switching mode (Power Switching Mode = logic 0), this ﬁeld is not valid.

Bit 0 — Reserved

Bit 1 — Ganged-power mask on port 1

Bit 2 — Ganged-power mask on port 2

15 to 0 DR

[15:0]

Device Removable: Each bit is dedicated to a port of the Root Hub. When

cleared, the attached device is removable. When set, the attached device is

not removable.

Bit 0 — Reserved

Bit 1 — Device attached to port 1

Bit 2 — Device attached to port 2

11.1.21 HcRhStatus register

This register is divided into two parts. The lower word of a double word represents the

Hub Status ﬁeld, and the upper word represents the Hub Status Change ﬁeld. Reserved

bits should always be written as logic 0. Table 82 shows the bit allocation of the register.

Table 82. HcRhStatus - Host Controller Root Hub Status register bit allocation

Address: Value read from func0 or func1 of address 10h + 50h

Bit

31

CRWE

0

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

17

0

R/W

16

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

Symbol

Reset

Access

Bit

reserved^[1]

CCIC

0

LPSC

0

R/W

15

0

R/W

0

R/W

14

R/W

13

R/W

12

R/W

10

R/W

9

R/W

8

11

Symbol

Reset

Access

DRWE

0

reserved^[1]

0

R/W

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

55 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

7

6

5

4

3

2

1

OCI

0

LPS

0

Symbol

reserved^[1]

Reset

0

Access

R/W

R

RW

[1] The reserved bits should always be written with the reset value.

Table 83. HcRhStatus - Host Controller Root Hub Status register bit description

Address: Value read from func0 or func1 of address 10h + 50h

Bit

Symbol

Description

31

CRWE

On write—Clear Remote Wakeup Enable:

0 — No effect

1 — Clears DRWE (Device Remote Wakeup Enable)

30 to 18 reserved

-

17

CCIC

Over Current Indicator Change: This bit is set by hardware when a

change has occurred to the OCI bit of this register.

0 — No effect

1 — The HCD clears this bit

16

LPSC

On read—Local Power Status Change: The Root Hub does not support

the local power status feature. Therefore, this bit is always logic 0.

On write—Set Global Power: In global power mode

(Power Switching Mode = logic 0), logic 1 is written to this bit to turn on

power to all ports (clear Port Power Status). In per-port power mode, it sets

Port Power Status only on ports whose Port Power Control Mask bit is not

set. Writing logic 0 has no effect.

15

DRWE

On read—Device Remote Wakeup Enable: This bit enables bit Connect

Status Change (CSC) as a resume event, causing a state transition from

USBSUSPEND to USBRESUME and setting the Resume Detected

interrupt.

0 — CSC is not a remote wake-up event

1 — CSC is a remote wake-up event

On write—Set Remote Wakeup Enable: Writing logic 1 sets DRWE

(Device Remote Wakeup Enable). Writing logic 0 has no effect.

14 to 2 reserved

-

1

OCI

Over Current Indicator: This bit reports overcurrent conditions when

global reporting is implemented. When set, an overcurrent condition exists.

When cleared, all power operations are normal. If the per-port overcurrent

protection is implemented, this bit is always logic 0.

0

LPS

On read—Local Power Status: The Root Hub does not support the local

power status feature. Therefore, this bit is always read as logic 0.

On write—Clear Global Power: In global power mode

(Power Switching Mode = logic 0), logic 1 is written to this bit to turn off

power to all ports (clear Port Power Status). In per-port power mode, it

clears Port Power Status only on ports whose Port Power Control Mask bit

is not set. Writing logic 0 has no effect.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

56 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.1.22 HcRhPortStatus[4:1] register

The HcRhPortStatus[4:1] register is used to control and report port events on a per-port

basis. Number Downstream Ports represents the number of HcRhPortStatus registers

that are implemented in hardware. The lower word reﬂects the port status. The upper

word reﬂects the status change bits. Some status bits are implemented with special write

behavior. If a transaction—token through handshake—is in progress when a write to

change port status occurs, the resulting port status change is postponed until the

transaction completes. Always write logic 0 to the reserved bits. The bit allocation of the

register is given in Table 84.

Table 84. HcRhPortStatus[4:1] - Host Controller Root Hub Port Status[4:1] register bit

allocation

Address: Value read from func0 or func1 of address 10h + 54h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

22

0

R/W

20

0

R/W

19

0

R/W

18

0

R/W

17

0

R/W

16

R/W

23

R/W

21

Symbol

Reset

Access

Bit

reserved^[1]

PRSC

0

OCIC

0

PSSC

0

PESC

0

CSC

0

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

R/W

9

R/W

8

Symbol

Reset

Access

Bit

reserved^[1]

LSDA

0

PPS

0

R/W

7

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

R/W

1

R/W

0

6

reserved^[1]

0

Symbol

Reset

Access

PRS

0

POCI

0

PSS

0

PES

0

CCS

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 85. HcRhPortStatus[4:1] - Host Controller Root Hub Port Status[4:1] register bit

description

Address: Value read from func0 or func1 of address 10h + 54h

Bit

Symbol

Description

31 to 21 reserved

-

20

19

PRSC

OCIC

Port Reset Status Change: This bit is set at the end of the 10 ms port

reset signal. The HCD can write logic 1 to clear this bit. Writing logic 0 has

no effect.

0 — Port reset is not complete

1 — Port reset is complete

Port Over Current Indicator Change: This bit is valid only if overcurrent

conditions are reported on a per-port basis. This bit is set when the Root

Hub changes the POCI (Port Over Current Indicator) bit. The HCD can write

logic 1 to clear this bit. Writing logic 0 has no effect.

0 — No change in POCI

1 — POCI has changed

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

57 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 85. HcRhPortStatus[4:1] - Host Controller Root Hub Port Status[4:1] register bit

description …continued

Address: Value read from func0 or func1 of address 10h + 54h

Bit

Symbol

Description

18

PSSC

Port Suspend Status Change: This bit is set when the resume sequence

is completed. This sequence includes the 20 ms resume pulse, LS EOP

and 3 ms resynchronization delay. The HCD can write logic 1 to clear this

bit. Writing logic 0 has no effect. This bit is also cleared when

ResetStatusChange is set.

0 — Resume is not completed

1 — Resume is completed

17

16

PESC

CSC

Port Enable Status Change: This bit is set when hardware events cause

the PES (Port Enable Status) bit to be cleared. Changes from the HCD

writes do not set this bit. The HCD can write logic 1 to clear this bit. Writing

logic 0 has no effect.

0 — No change in PES

1 — Change in PES

Connect Status Change: This bit is set whenever a connect or disconnect

event occurs. The HCD can write logic 1 to clear this bit. Writing logic 0 has

no effect. If CCS (Current Connect Status) is cleared when a Set Port

Reset, Set Port Enable or Set Port Suspend write occurs, this bit is set to

force the driver to re-evaluate the connection status because these writes

should not occur if the port is disconnected.

0 — No change in CCS

1 — Change in CCS

Remark: If the Device Removable [NDP] bit is set, this bit is set only after a

Root Hub reset to inform the system that the device is attached.

15 to 10 reserved

LSDA

-

9

On read—Low Speed Device Attached: This bit indicates the speed of the

device attached to this port. When set, a low-speed device is attached to

this port. When cleared, a full-speed device is attached to this port. This

ﬁeld is valid only when CCS is set.

0 — Port is not suspended

1 — Port is suspended

On write—Clear Port Power: The HCD can clear the PPS (Por Power

Status) bit by writing logic 1 to this bit. Writing logic 0 has no effect.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

58 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 85. HcRhPortStatus[4:1] - Host Controller Root Hub Port Status[4:1] register bit

description …continued

Address: Value read from func0 or func1 of address 10h + 54h

Bit

Symbol

Description

8

PPS

On read—Port Power Status: This bit reﬂects the port power status,

regardless of the type of power switching implemented. This bit is cleared if

an overcurrent condition is detected. The HCD can set this bit by writing Set

Port Power or Set Global Power. The HCD can clear this bit by writing Clear

Port Power or Clear Global Power. Power Switching Mode and Port Power

Control Mask [NDP] determine which power control switches are enabled.

In global switching mode (Power Switching Mode = logic 0), only Set/Clear

Global Power controls this bit. In the per-port power switching

(Power Switching Mode = logic 1), if the Port Power Control Mask [NDP] bit

for the port is set, only Set/Clear Port Power commands are enabled. If the

mask is not set, only Set/Clear Global Power commands are enabled.

When port power is disabled, bits CCS (Current Connect Status), PES (Port

Enable Status), PSS (Port Suspend Status) and PRS (Port Reset Status)

should be reset.

0 — Port power is off

1 — Port power is on

On write—Set Port Power: The HCD can write logic 1 to set the PPS (Port

Power Status) bit. Writing logic 0 has no effect.

Remark: This bit always reads logic 1 if power switching is not supported.

7 to 5

4

reserved

PRS

-

On read—Port Reset Status: When this bit is set by a write to Set Port

Reset, port reset signaling is asserted. When reset is completed and PRSC

is set, this bit is cleared.

0 — Port reset signal is inactive

1 — Port reset signal is active

On write—Set Port Reset: The HCD can set the port reset signaling by

writing logic 1 to this bit. Writing logic 0 has no effect. If CCS is cleared, this

write does not set PRS (Port Reset Status) but instead sets CCS. This

informs the driver that it attempted to reset a disconnected port.

3

POCI

On read—Port Over Current Indicator: This bit is valid only when the Root

Hub is conﬁgured to show overcurrent conditions are reported on a per-port

basis. If the per-port overcurrent reporting is not supported, this bit is set to

logic 0. If cleared, all power operations are normal for this port. If set, an

overcurrent condition exists on this port.

0 — No overcurrent condition

1 — Overcurrent condition detected

On write—Clear Suspend Status: The HCD can write logic 1 to initiate a

resume. Writing logic 0 has no effect. A resume is initiated only if PSS (Port

Suspend Status) is set.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

59 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 85. HcRhPortStatus[4:1] - Host Controller Root Hub Port Status[4:1] register bit

description …continued

Address: Value read from func0 or func1 of address 10h + 54h

Bit

Symbol

Description

2

PSS

On read—Port Suspend Status: This bit indicates whether the port is

suspended or is in the resume sequence. It is set by a Set Suspend State

write and cleared when PSSC (Port Suspend Status Change) is set at the

end of the resume interval. This bit is not set if CCS (Current Connect

Status) is cleared. This bit is also cleared when PRSC is set at the end of

the port reset or when the Host Controller is placed in the USBRESUME

state. If an upstream resume is in progress, it will propagate to the Host

Controller.

0 — Port is not suspended

1 — Port is suspended

On write—Set Port Suspend: The HCD can set the PSS (Port Suspend

Status) bit by writing logic 1 to this bit. Writing logic 0 has no effect. If CCS

is cleared, this write does not set PSS; instead it sets CSS. This informs the

driver that it attempted to suspend a disconnected port.

1

PES

On read—Port Enable Status: This bit indicates whether the port is

enabled or disabled. The Root Hub may clear this bit when an overcurrent

condition, disconnect event, switched-off power or operational bus error is

detected. This change also causes Port Enabled Status Change to be set.

The HCD can set this bit by writing Set Port Enable and clear it by writing

Clear Port Enable. This bit cannot be set when CCS (Current Connect

Status) is cleared. This bit is also set on completing a port reset when

Reset Status Change is set or on completing a port suspend when

Suspend Status Change is set.

0 — Port is disabled

1 — Port is enabled

On write—Set Port Enable: The HCD can set PES (Port Enable Status) by

writing logic 1. Writing logic 0 has no effect. If CCS is cleared, this write

does not set PES, but instead sets CSC (Connect Status Change). This

informs the driver that it attempted to enable a disconnected port.

0

CCS

On read—Current Connect Status: This bit reﬂects the current state of the

downstream port.

0 — No device connected

1 — Device connected

On write—Clear Port Enable: The HCD can write logic 1 to this bit to clear

the PES (Port Enable Status) bit. Writing logic 0 has no effect. The CCS bit

is not affected by any write.

Remark: This bit always reads logic 1 when the attached device is

nonremovable (Device Removable [NDP]).

11.2 EHCI controller capability registers

Other than the OHCI Host Controller, there are some registers in EHCI that deﬁne the

capability of EHCI. The address range of these registers is located before the operational

registers.

11.2.1 CAPLENGTH/HCIVERSION register

The bit allocation of this 4 B register is given in Table 86.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

60 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 86. CAPLENGTH/HCIVERSION - Capability Registers Length/Host Controller

Interface Version Number register bit allocation

Address: Value read from func2 of address 10h + 00h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

HCIVERSION[15:8]

0

R

0

R

0

R

0

R

0

R

0

R

0

R

1

R

23

22

21

20

19

18

17

16

Symbol

Reset

Access

Bit

HCIVERSION[7:0]

0

R

0

R

0

R

0

R

0

R

0

R

0

R

9

0

R

8

15

14

13

12

11

10

Symbol

Reset

Access

Bit

reserved

0

R

7

0

R

6

0

R

5

0

R

4

0

R

3

0

R

2

0

R

1

0

R

0

Symbol

Reset

Access

CAPLENGTH[7:0]

0

1

0

R

Table 87. CAPLENGTH/HCIVERSION - Capability Registers Length/Host Controller

Interface Version Number register bit description

Address: Value read from func2 of address 10h + 00h

Bit

Symbol

Description

31 to 16 HCIVERSION Host Controller Interface Version Number: This ﬁeld contains a BCD

[15:0]

encoded version number of the interface to which the Host Controller

interface conforms.

15 to 8 reserved

-

7 to 0

CAPLENGTH Capability Register Length: This is used as an offset. It is added to

[7:0] the register base to ﬁnd the beginning of the operational register space.

11.2.2 HCSPARAMS register

The Host Controller Structural Parameters (HCSPARAMS) register is a set of ﬁelds that

are structural parameters. The bit allocation is given in Table 88.

Table 88. HCSPARAMS - Host Controller Structural Parameters register bit allocation

Address: Value read from func2 of address 10h + 04h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved

0

R

0

R

0

R

0

R

0

R

0

R

0

R

0

R

23

22

21

20

19

18

17

16

Symbol

Reset

Access

reserved

0

R

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

61 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

15

14

13

12

11

10

9

8

Symbol

N_CC[3:0]

N_PCC[3:0]

Reset

Access

Bit

0

R

0

R

6

1

R

5

0

R

0

R

3

0

R

2

0

R

1

R

0

7

4

Symbol

Reset

Access

PRR

1

reserved

PPC

1

N_PORTS[3:0]

0

1

0

R

Table 89. HCSPARAMS - Host Controller Structural Parameters register bit description

Address: Value read from func2 of address 10h + 04h

Bit

Symbol

Description

31 to 16

15 to 12

reserved

-

N_CC[3:0] Number of Companion Controller: This ﬁeld indicates the number of

companion controllers associated with this Hi-Speed USB Host

Controller. A value of zero in this ﬁeld indicates there are no companion

Host Controllers. Port-ownership hand-off is not supported. Only

high-speed devices are supported on the Host Controller root ports. A

value larger than zero in this ﬁeld indicates there are companion Original

USB Host Controller(s). Port-ownership hand-offs are supported.

11 to 8

N_PCC

[3:0]

Number of Ports per Companion Controller: This ﬁeld indicates the

number of ports supported per companion Host Controller. It is used to

indicate the port routing conﬁguration to the system software. For

example, if N_PORTS has a value of 6 and N_CC has a value of 2, then

N_PCC can have a value of 3. The convention is that the ﬁrst N_PCC

ports are assumed to be routed to companion controller 1, the next

N_PCC ports to companion controller 2, and so on. In the previous

example, N_PCC could have been 4, in which case the ﬁrst four are

routed to companion controller 1 and the last two are routed to

companion controller 2.

The number in this ﬁeld must be consistent with N_PORTS and N_CC.

7

PRR

Port Routing Rules: This ﬁeld indicates the method used to map ports

to companion controllers.

0 — The ﬁrst N_PCC ports are routed to the lowest numbered function

companion Host Controller, the next N_PCC ports are routed to the next

lowest function companion controller, and so on

1 — The port routing is explicitly enumerated by the ﬁrst N_PORTS

elements of the HCSP-PORTROUTE array

6 and 5

4

reserved

PPC

-

Port Power Control: This ﬁeld indicates whether the Host Controller

implementation includes port power control. Logic 1 indicates the port

has port power switches. Logic 0 indicates the port does not have port

power switches. The value of this ﬁeld affects the functionality of the Port

Power ﬁeld in each port status and control register.

3 to 0

N_PORTS N_Ports: This ﬁeld speciﬁes the number of physical downstream ports

[3:0]

implemented on this Host Controller. The value in this ﬁeld determines

how many port registers are addressable in the operational register

space. Logic 0 in this ﬁeld is undeﬁned.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

62 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.2.3 HCCPARAMS register

The Host Controller Capability Parameters (HCCPARAMS) register is a 4 B register, and

the bit allocation is given in Table 90.

Table 90. HCCPARAMS - Host Controller Capability Parameters register bit allocation

Address: Value read from func2 of address 10h + 08h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved

0

R

0

R

0

R

0

R

0

R

0

R

0

R

0

R

23

22

21

20

19

18

17

16

Symbol

Reset

Access

Bit

reserved

0

R

0

R

0

R

0

R

0

R

0

R

0

R

9

0

R

8

15

14

13

12

11

10

Symbol

Reset

Access

Bit

reserved

0

R

7

0

R

6

0

R

5

0

R

4

0

R

3

0

R

2

0

R

0

R

1

0

Symbol

Reset

Access

IST[3:0]

reserved

PFLF

1

64AC

0

1

0

R

Table 91. HCCPARAMS - Host Controller Capability Parameters register bit description

Address: Value read from func2 of address 10h + 08h

Bit

31 to 8 reserved

7 to 4

Symbol Description

-

IST[3:0] Isochronous Scheduling Threshold: Default = implementation dependent.

This ﬁeld indicates—relative to the current position of the executing Host

Controller—where software can reliably update the isochronous schedule.

When IST[3] is logic 0, the value of the least signiﬁcant three bits indicates

the number of micro frames a Host Controller can hold a set of isochronous

data structures—one or more—before ﬂushing the state. When IST[3] is

logic 1, the host software assumes the Host Controller may cache an

isochronous data structure for an entire frame.

3 and 2 reserved

-

1

PFLF

Programmable Frame List Flag: Default = implementation dependent. If

this bit is cleared, the system software must use a frame list length of

1024 elements with the Host Controller. The USBCMD register FLS[1:0]

(bit 3 and bit 2) is read-only and should be cleared. If PFLF is set, the system

software can specify and use a smaller frame list and conﬁgure the host

through the FLS bit. The frame list must always be aligned on a 4 kB page

boundary to ensure that the frame list is always physically contiguous.

0

64AC

64-bit Addressing Capability: This ﬁeld contains the addressing range

capability.

0 — Data structures using 32-bit address memory pointers

1 — Data structures using 64-bit address memory pointers

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

63 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.2.4 HCSP-PORTROUTE register

The HCSP-PORTROUTE (Companion Port Route Description) register is an optional

read-only ﬁeld that is valid only if PRR (bit 7 in the HCSPARAMS register) is logic 1. Its

address is value read from func2 of address 10h + 0Ch.

This ﬁeld is a 15-element nibble array—each 4 bits is one array element. Each array

location corresponds one-to-one with a physical port provided by the Host Controller. For

example, PORTROUTE[0] corresponds to the ﬁrst PORTSC port, PORTROUTE[1] to the

second PORTSC port, and so on. The value of each element indicates to which of the

companion Host Controllers this port is routed. Only the ﬁrst N_PORTS elements have

valid information. A value of zero indicates that the port is routed to the lowest numbered

function companion Host Controller. A value of one indicates that the port is routed to the

next lowest numbered function companion Host Controller, and so on.

11.3 Operational registers of Enhanced USB Host Controller

11.3.1 USBCMD register

The USB Command (USBCMD) register indicates the command to be executed by the

serial Host Controller. Writing to this register causes a command to be executed. Table 92

shows the bit allocation.

Table 92. USBCMD - USB Command register bit allocation

Address: Value read from func2 of address 10h + 20h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

ITC[7:0]

0

1

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

7

0

R/W

6

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

R/W

5

R/W

4

Symbol

LHCR

IAAD

ASE

PSE

FLS[1:0]

HC

RS

RESET

Reset

0

Access

R/W

[1] The reserved bits should always be written with the reset value.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

64 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 93. USBCMD - USB Command register bit description

Address: Value read from func2 of address 10h + 20h

Bit

Symbol

Description

31 to 24 reserved

23 to 16 ITC[7:0]

-

Interrupt Threshold Control: Default = 08h. This ﬁeld is used by the

system software to select the maximum rate at which the Host Controller

will issue interrupts. If software writes an invalid value to this register, the

results are undeﬁned. Valid values are:

00h — reserved

01h — 1 micro frame

02h — 2 micro frames

04h — 4 micro frames

08h — 8 micro frames (equals 1 ms)

10h — 16 micro frames (equals 2 ms)

20h — 32 micro frames (equals 4 ms)

40h — 64 micro frames (equals 8 ms)

Software modiﬁcations to this ﬁeld while HCH (bit 12) in the USBSTS

register is zero results in undeﬁned behavior.

15 to 8

7

reserved

LHCR

-

Light Host Controller Reset: This control bit is not required. It allows the

driver software to reset the EHCI controller, without affecting the state of

the ports or the relationship to the companion Host Controllers. If not

implemented, a read of this ﬁeld will always return zero. If implemented, on

read:

0 — Indicates that the Light Host Controller Reset has completed and it is

ready for the host software to reinitialize the Host Controller

1 — Indicates that the Light Host Controller Reset has not yet completed

6

IAAD

Interrupt on Asynchronous Advance Doorbell: This bit is used as a

doorbell by software to notify the Host Controller to issue an interrupt the

next time it advances the asynchronous schedule. Software must write

logic 1 to this bit to ring the doorbell. When the Host Controller has evicted

all appropriate cached schedule states, it sets IAA (bit 5 in the USBSTS

register). If IAAE (bit 5 in the USBINTR register) is logic 1, then the Host

Controller will assert an interrupt at the next interrupt threshold. The Host

Controller sets this bit to logic 0 after it sets IAA. Software should not set

this bit when the asynchronous schedule is inactive because this results in

an undeﬁned value.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

65 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 93. USBCMD - USB Command register bit description …continued

Address: Value read from func2 of address 10h + 20h

Bit

Symbol

Description

5

ASE

Asynchronous Schedule Enable: Default = logic 0. This bit controls

whether the Host Controller skips processing the asynchronous schedule.

0 — Do not process the asynchronous schedule

1 — Use the ASYNCLISTADDR register to access the asynchronous

schedule

4

PSE

Periodic Schedule Enable: Default = logic 0. This bit controls whether

the Host Controller skips processing the periodic schedule.

0 — Do not process the periodic schedule

1 — Use the PERIODICLISTBASE register to access the periodic

schedule

3 and 2

FLS[1:0]

Frame List Size: Default = 00b. This ﬁeld is read and write only if PFLF

(bit 1) in the HCCPARAMS register is set to logic 1. This ﬁeld speciﬁes the

size of the frame list. The size the frame list controls which bits in the

Frame Index register should be used for the frame list current index.

00b — 1024 elements (4096 B)

01b — 512 elements (2048 B)

10b — 256 elements (1024 B) for small environments

11b — reserved

1

HCRESET Host Controller Reset: This control bit is used by the software to reset

the Host Controller. The effects of this on Root Hub registers are similar to

a chip hardware reset. Setting this bit causes the Host Controller to reset

its internal pipelines, timers, counters, state machines, and so on, to their

initial values. Any transaction currently in progress on USB is immediately

terminated. A USB reset is not driven on downstream ports. This reset

does not affect the PCI Conﬁguration registers. All operational registers,

including port registers and port state machines, are set to their initial

values. Port ownership reverts to the companion Host Controller(s). The

software must reinitialize the Host Controller to return it to an operational

state. This bit is cleared by the Host Controller when the reset process is

complete. Software cannot terminate the reset process early by writing

logic 0 to this register. Software should check that bit HCH is logic 0 before

setting this bit. Attempting to reset an actively running Host Controller

results in undeﬁned behavior.

0

RS

Run/Stop: logic 1 = Run. logic 0 = Stop. When set, the Host Controller

executes the schedule. The Host Controller continues execution as long

as this bit is set. When this bit is cleared, the Host Controller completes

the current and active transactions in the USB pipeline, and then halts.

Bit HCH indicates when the Host Controller has ﬁnished the transaction

and has entered the stopped state. Software should check that the HCH

bit is logic 1, before setting this bit.

11.3.2 USBSTS register

The USB Status (USBSTS) register indicates pending interrupts and various states of the

Host Controller. The status resulting from a transaction on the serial bus is not indicated in

this register. Software clears the register bits by writing ones to them. The bit allocation is

given in Table 94.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

66 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 94. USBSTS - USB Status register bit allocation

Address: Value read from func2 of address 10h + 24h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

15

ASS

0

R/W

13

0

R/W

12

0

R/W

9

0

R/W

8

R/W

11

R/W

10

reserved^[1]

14

Symbol

Reset

Access

Bit

PSSTAT

RECL

0

HCH

1

0

R

6

0

R/W

1

0

R/W

0

R

R/W

3

R/W

2

7

5

4

Symbol

reserved^[1]

IAA

HSE

FLR

PCD

USB

USBINT

ERRINT

Reset

0

Access

R/W

R

R/W

[1] The reserved bits should always be written with the reset value.

Table 95. USBSTS - USB Status register bit description

Address: Value read from func2 of address 10h + 24h

Bit

Symbol

reserved

ASS

Description

31 to 16

15

-

Asynchronous Schedule Status: Default = logic 0. The bit reports the

current real status of the asynchronous schedule. If this bit is logic 0,

the status of the asynchronous schedule is disabled. If this bit is logic 1,

the status of the asynchronous schedule is enabled. The Host

Controller is not required to immediately disable or enable the

asynchronous schedule when software changes ASE (bit 5 in the

USBCMD register). When this bit and the ASE bit have the same value,

the asynchronous schedule is either enabled (1) or disabled (0).

14

PSSTAT

Periodic Schedule Status: Default = logic 0. This bit reports the

current status of the periodic schedule. If this bit is logic 0, the status of

the periodic schedule is disabled. If this bit is logic 1, the status of the

periodic schedule is enabled. The Host Controller is not required to

immediately disable or enable the periodic schedule when software

changes PSE (bit 4) in the USBCMD register. When this bit and the

PSE bit have the same value, the periodic schedule is either enabled (1)

or disabled (0).

13

12

RECL

HCH

Reclamation: Default = logic 0. This is a read-only status bit that is

used to detect an empty asynchronous schedule.

HCHalted: Default = logic 1. This bit is logic 0 when RS (bit 0) in the

USBCMD register is logic 1. The Host Controller sets this bit to logic 1

after it has stopped executing because the RS bit is set to logic 0, either

by software or by the Host Controller hardware. For example, on an

internal error.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

67 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 95. USBSTS - USB Status register bit description …continued

Address: Value read from func2 of address 10h + 24h

Bit

Symbol

reserved

IAA

Description

11 to 6

5

-

Interrupt on Asynchronous Advance: Default = logic 0. The system

software can force the Host Controller to issue an interrupt the next time

the Host Controller advances the asynchronous schedule by writing

logic 1 to IAAD (bit 6) in the USBCMD register. This status bit indicates

the assertion of that interrupt source.

4

3

HSE

FLR

Host System Error: The Host Controller sets this bit when a serious

error occurs during a host system access, involving the Host Controller

module. In a PCI system, conditions that set this bit include PCI parity

error, PCI master abort and PCI target abort. When this error occurs,

the Host Controller clears RS (bit 0 in the USBCMD register) to prevent

further execution of the scheduled TDs.

Frame List Rollover: The Host Controller sets this bit to logic 1 when

the frame list index rolls over from its maximum value to zero. The exact

value at which the rollover occurs depends on the frame list size. For

example, if the frame list size—as programmed in FLS (bit 3 and bit 2)

of the USBCMD register—is 1024, the Frame Index register rolls over

every time bit 13 of the FRINDEX register toggles. Similarly, if the size is

512, the Host Controller sets this bit to logic 1 every time bit 12 of the

FRINDEX register toggles.

2

PCD

Port Change Detect: The Host Controller sets this bit to logic 1 when

any port— where PO (bit 13 of PORTSC) is cleared—changes to

logic 1, or FPR (bit 6 of PORTSC) changes to logic 1 as a result of a

J-to-K transition detected on a suspended port. This bit is allowed to be

maintained in the auxiliary power well. Alternatively, it is also acceptable

that—on a D3-to-D0 transition of the EHCI Host Controller device—this

bit is loaded with the logical OR of all the PORTSC change bits,

including force port resume, overcurrent change, enable or disable

change, and connect status change.

1

0

USB

ERRINT

USB Error Interrupt: The Host Controller sets this bit when an error

condition occurs because of completing a USB transaction. For

example, error counter underﬂow. If the Transfer Descriptor (TD) on

which the error interrupt occurred also had its IOC bit set, both this bit

and the USBINT bit are set. For details, refer to the Enhanced Host

Controller Interface Speciﬁcation for Universal Serial Bus Rev. 1.0.

USBINT

USB Interrupt: The Host Controller sets this bit on completing a USB

transaction, which results in the retirement of a TD that had its IOC bit

set. The Host Controller also sets this bit when a short packet is

detected, that is, the actual number of bytes received was less than the

expected number of bytes. For details, refer to the Enhanced Host

Controller Interface Speciﬁcation for Universal Serial Bus Rev. 1.0.

11.3.3 USBINTR register

The USB Interrupt Enable (USBINTR) register enables and disables reporting of the

corresponding interrupt to the software. When a bit is set and the corresponding interrupt

is active, an interrupt is generated to the host. Interrupt sources that are disabled in this

register still appear in USBSTS to allow the software to poll for events. The USBSTS

register bit allocation is given in Table 96.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

68 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 96. USBINTR - USB Interrupt Enable register bit allocation

Address: Value read from func2 of address 10h + 28h

Bit

31

30

29

28

27

reserved^[1]

0

26

25

24

Symbol

Reset

Access

Bit

0

R/W

23

R/W

22

R/W

21

R/W

18

R/W

17

R/W

16

20

19

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

10

12

11

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

2

0

R/W

1

0

R/W

4

R/W

3

0

Symbol

reserved^[1]

IAAE

HSEE

FLRE

PCIE

USB

USBINTE

ERRINTE

Reset

0

Access

R/W

[1] The reserved bits should always be written with the reset value.

Table 97. USBINTR - USB Interrupt Enable register bit description

Address: Value read from func2 of address 10h + 28h

Bit

Symbol

reserved

IAAE

Description

31 to 6

5

-

Interrupt on Asynchronous Advance Enable: When this bit and IAA

(bit 5 in the USBSTS register) are set, the Host Controller issues an

interrupt at the next interrupt threshold. The interrupt is acknowledged by

software clearing bit IAA.

4

3

2

1

HSEE

FLRE

PCIE

USB

Host System Error Enable: When this bit and HSE (bit 4 in the USBSTS

register) are set, the Host Controller issues an interrupt. The interrupt is

acknowledged by software clearing bit HSE.

Frame List Rollover Enable: When this bit and FLR (bit 3 in the

USBSTS register) are set, the Host Controller issues an interrupt. The

interrupt is acknowledged by software clearing bit FLR.

Port Change Interrupt Enable: When this bit and PCD (bit 2 in the

USBSTS register) are set, the Host Controller issues an interrupt. The

interrupt is acknowledged by software clearing bit PCD.

USB Error Interrupt Enable: When this bit and USBERRINT (bit 1 in the

ERRINTE USBSTS register) are set, the Host Controller issues an interrupt at the

next interrupt threshold. The interrupt is acknowledged by software

clearing bit USBERRINT.

0

USBINTE USB Interrupt Enable: When this bit and USBINT (bit 0 in the USBSTS

register) are set, the Host Controller issues an interrupt at the next

interrupt threshold. The interrupt is acknowledged by software clearing

bit USBINT.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

69 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.3.4 FRINDEX register

The Frame Index (FRINDEX) register is used by the Host Controller to index into the

periodic frame list. The register updates every 125 µs—once each micro frame.

Bits N to 3 are used to select a particular entry in the periodic frame list during periodic

schedule execution. The number of bits used for the index depends on the size of the

frame list as set by the system software in FLS[1:0] (bit 3 and bit 2) of the USBCMD

register. This register must be written as a double word. Byte writes produce undeﬁned

results. This register cannot be written unless the Host Controller is in the halted state, as

indicated by HCH (bit 12 in the USBSTS register). A write to this register while RS (bit 0 in

the USBCMD register) is set produces undeﬁned results. Writes to this register also affect

the SOF value.

The bit allocation is given in Table 98.

Table 98. FRINDEX - Frame Index register bit allocation

Address: Value read from func2 of address 10h + 2Ch

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

reserved^[1]

FRINDEX[13:8]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol

Reset

Access

FRINDEX[7:0]

0

R/W

[1] The reserved bits should always be written with the reset value.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

70 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 99. FRINDEX - Frame Index register bit description

Address: Value read from func2 of address 10h + 2Ch

Bit

31 to 14 reserved

13 to 0

Symbol

Description

-

FRINDEX Frame Index: Bits in this register are used for the frame number in the SOF

[13:0]

packet and as the index into the frame list. The value in this register

increments at the end of each time frame. For example, micro frame. The

bits used for the frame number in the SOF token are taken from bits 13 to 3

of this register. Bits N to 3 are used for the frame list current index. This

means that each location of the frame list is accessed eight times—frames

or micro frames—before moving to the next index.

The following illustrates values of N based on the value of FLS[1:0]

(bit 3 and bit 2 in the USBCMD register).

FLS[1:0]

00b

Number elements

N

1024

512

12

11

10

-

01b

10b

256

11b

reserved

11.3.5 PERIODICLISTBASE register

The Periodic Frame List Base Address (PERIODLISTBASE) register contains the

beginning address of the periodic frame list in the system memory. If the Host Controller is

in 64-bit mode—as indicated by logic 1 in 64AC (bit 0 of the HCCSPARAMS register)—the

most signiﬁcant 32 bits of every control data structure address comes from the

CTRLDSSEGMENT register. The system software loads this register before starting the

schedule execution by the Host Controller. The memory structure referenced by this

physical memory pointer is assumed as 4 kB aligned. The contents of this register are

combined with the FRINDEX register to enable the Host Controller to step through the

periodic frame list in sequence.

The bit allocation is given in Table 100.

Table 100. PERIODICLISTBASE - Periodic Frame List Base Address register bit allocation

Address: Value read from func2 of address 10h + 34h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

BA[19:12]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

BA[11:4]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

BA[3:0]

reserved^[1]

0

R/W

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

71 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Bit

7

6

5

4

3

2

1

0

Symbol

reserved^[1]

Reset

0

Access

R/W

[1] The reserved bits should always be written with the reset value.

Table 101. PERIODICLISTBASE - Periodic Frame List Base Address register bit description

Address: Value read from func2 of address 10h + 34h

Bit

Symbol

Description

31 to 12

BA[19:0]

Base Address: These bits correspond to memory address signals

31 to 12, respectively.

11 to 0

reserved

-

11.3.6 ASYNCLISTADDR register

This 32-bit register contains the address of the next asynchronous queue head to be

executed. If the Host Controller is in 64-bit mode—as indicated by logic 1 in 64AC (bit 0 of

the HCCPARAMS register)—the most signiﬁcant 32 bits of every control data structure

address comes from the CTRLDSSEGMENT register. Bits 4 to 0 of this register always

return zeros when read. The memory structure referenced by the physical memory pointer

is assumed as 32 B (cache aligned). For bit allocation, see Table 102.

Table 102. ASYNCLISTADDR - Current Asynchronous List Address register bit allocation

Address: Value read from func2 of address 10h + 38h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

LPL[19:12]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

LPL[11:4]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

LPL[3:0]

reserved^[1]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

4

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

Symbol

Reset

Access

reserved^[1]

0

R/W

[1] The reserved bits should always be written with the reset value.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

72 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 103. ASYNCLISTADDR - Current Asynchronous List Address register bit description

Address: Value read from func2 of address 10h + 38h

Bit

Symbol

Description

31 to 12

LPL[19:0] Link Pointer List: These bits correspond to memory address signals

31 to 12, respectively. This ﬁeld may only reference a Queue Head (QH).

11 to 0

reserved

-

11.3.7 CONFIGFLAG register

The bit allocation of the Conﬁgure Flag (CONFIGFLAG) register is given in Table 104.

Table 104. CONFIGFLAG - Conﬁgure Flag register bit allocation

Address: Value read from func2 of address 10h + 60h

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

9

0

R/W

8

R/W

15

R/W

14

R/W

13

R/W

12

R/W

11

R/W

10

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

7

0

R/W

6

0

R/W

5

0

R/W

3

0

R/W

2

0

R/W

1

0

R/W

0

R/W

4

reserved^[1]

0

Symbol

Reset

Access

CF

0

R/W

[1] The reserved bits should always be written with the reset value.

Table 105. CONFIGFLAG - Conﬁgure Flag register bit description

Address: Value read from func2 of address 10h + 60h

Bit

Symbol

reserved

CF

Description

31 to 1

0

-

Conﬁgure Flag: The host software sets this bit as the last action in its

process of conﬁguring the Host Controller. This bit controls the default

port-routing control logic.

0 — Port-routing control logic default-routes each port to an implementation

dependent classic Host Controller

1 — Port-routing control logic default-routes all ports to this Host Controller

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

73 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.3.8 PORTSC registers 1, 2

The Port Status and Control (PORTSC) register is in the auxiliary power well. It is only

reset by hardware when the auxiliary power is initially applied or in response to a Host

Controller reset. The initial conditions of a port are:

• No device connected

• Port disabled

If the port has power control, software cannot change the state of the port until it sets the

port power bits. Software must not attempt to change the state of the port until power is

stable on the port; maximum delay is 20 ms from the transition. For bit allocation, see

Table 106.

Table 106. PORTSC 1, 2 - Port Status and Control 1, 2 register bit allocation

Address: Value read from func2 of address 10h + 64h + (4 × Port Number − 1) where Port Number

is 1, 2

Bit

31

30

29

28

27

26

25

24

Symbol

Reset

Access

Bit

reserved^[1]

0

R/W

23

R/W

22

R/W

21

R/W

20

R/W

19

R/W

18

R/W

17

R/W

16

Symbol reserved WKOC_E WKDS WKCNNT

PTC[3:0]

CNNT_E

_E

Reset

Access

Bit

0

R/W

13

0

R/W

8

R/W

15

reserved^[1]

R/W

14

R/W

12

PP

0

R/W

11

R/W

10

R/W

9

Symbol

Reset

Access

Bit

PO

1

LS[1:0]

reserved^[1]

PR

0

R/W

7

0

R/W

6

0

R/W

3

0

R/W

2

0

R/W

1

R/W

5

R/W

4

R

0

Symbol

Reset

Access

SUSP

0

FPR

0

OCC

0

OCA

0

PEDC

0

PED

0

ECSC

0

ECCS

0

R/W

R

R/W

R

[1] The reserved bits should always be written with the reset value.

Table 107. PORTSC 1, 2 - Port Status and Control 1, 2 register bit description

Address: Value read from func2 of address 10h + 64h + (4 × Port Number − 1) where Port Number

is 1, 2

Bit

Symbol Description

reserved

31 to 23

22

-

WKOC_E Wake on Overcurrent Enable: Default = logic 0. Setting this bit enables

the port to be sensitive to overcurrent conditions as wake-up events.^[1]

21

20

WKDS

Wake on Disconnect Enable: Default = logic 0. Setting this bit enables

CNNT_E the port to be sensitive to device disconnects as wake-up events.^[1]

WKCNNT Wake on Connect Enable: Default = logic 0. Setting this bit enables the

_E

port to be sensitive to device connects as wake-up events.^[1]

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

74 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 107. PORTSC 1, 2 - Port Status and Control 1, 2 register bit description …continued

Address: Value read from func2 of address 10h + 64h + (4 × Port Number − 1) where Port Number

is 1, 2

Bit

Symbol Description

19 to 16

PTC[3:0] Port Test Control: Default = 0000b. When this ﬁeld is logic 0, the port is

not operating in test mode. A nonzero value indicates that it is operating in

test mode and test mode is indicated by the value. The encoding of the test

mode bits are:

0000b — Test mode disabled

0001b — Test J_STATE

0010b — Test K_STATE

0011b — Test SE0_NAK

0100b — Test packet

0101b — Test FORCE_ENABLE

0110b to 1111b — reserved

15 and 14 reserved

13 PO

-

Port Owner: Default = logic 1. This bit unconditionally goes to logic 0

when CF (bit 0) in the CONFIGFLAG register makes logic 0 to logic 1

transition. This bit unconditionally goes to logic 1 when the CF bit is logic 0.

The system software uses this ﬁeld to release ownership of the port to a

selected Host Controller, if the attached device is not a high-speed device.

Software writes logic 1 to this bit, if the attached device is not a high-speed

device. Logic 1 in this bit means that a companion Host Controller owns

and controls the port.

12

PP

Port Power: The function of this bit depends on the value of PPC (bit 4) in

the HCSPARAMS register.

If PPC = logic 0 and PP = logic 1 — The Host Controller does not have

port power control switches. Always powered

If PPC = logic 1 and PP = logic 1 or logic 0 — The Host Controller has

port power control switches. This bit represents the current setting of the

switch: logic 0 = off, logic 1 = on. When PP is logic 0, the port is

nonfunctional and will not report any status

When an overcurrent condition is detected on a powered port and PPC is

logic 1, the PP bit in each affected port may be changed by the Host

Controller from logic 1 to logic 0, removing power from the port.

11 and 10 LS[1:0]

Line Status: This ﬁeld reﬂects the current logical levels of the DP (bit 11)

and DM (bit 10) signal lines. These bits are used to detect low-speed USB

devices before the port reset and enable sequence. This ﬁeld is valid only

when the Port Enable bit is logic 0, and the Current Connect Status bit is

set to logic 1.

00b — SE0: Not a low-speed device, perform EHCI reset

01b — K-state: Low-speed device, release ownership of port

10b — J-state: Not a low-speed device, perform EHCI reset

11b — Undeﬁned: Not a low-speed device, perform EHCI reset

If the PP bit is logic 0, this ﬁeld is undeﬁned

-

9

reserved

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

75 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 107. PORTSC 1, 2 - Port Status and Control 1, 2 register bit description …continued

Address: Value read from func2 of address 10h + 64h + (4 × Port Number − 1) where Port Number

is 1, 2

Bit

Symbol Description

8

PR

Port Reset: Logic 1 means the port is in reset. Logic 0 means the port is

not in reset. Default = logic 0. When software sets this bit from logic 0, the

bus reset sequence as deﬁned in Universal Serial Bus Speciﬁcation

Rev. 2.0 is started. Software clears this bit to terminate the bus reset

sequence. Software must hold this bit at logic 1 until the reset sequence,

as speciﬁed in Universal Serial Bus Speciﬁcation Rev. 2.0, is completed.

Remark: When software sets this bit, it must also clear the Port Enable

bit.

Remark: When software clears this bit, there may be a delay before the bit

status changes to logic 0 because it will not read logic 0 until the reset is

completed. If the port is in high-speed mode after reset is completed, the

Host Controller will automatically enable this port; it can set the Port

Enable bit. A Host Controller must terminate the reset and stabilize the

state of the port within 2 ms of software changing this bit from logic 1 to

logic 0. For example, if the port detects that the attached device is

high-speed during a reset, then the Host Controller must enable the port

within 2 ms of software clearing this bit.

HCH (bit 12) in the USBSTS register must be logic 0 before software

attempts to use this bit. The Host Controller may hold Port Reset asserted

when the HCH bit is set.^[1]

7

SUSP

Suspend: Default = logic 0. Logic 1 means the port is in the suspend

state. Logic 0 means the port is not suspended. The PED (Port Enabled)

bit and this bit deﬁne the port states as follows:

PED = logic 0 and SUSP = X — Port is disabled

PED = logic 1 and SUSP = logic 0 — Port is enabled

PED = logic 1 and SUSP = logic 1 — Port is suspended

When in the suspend state, downstream propagation of data is blocked on

this port, except for the port reset. If a transaction was in progress when

this bit was set, blocking occurs at the end of the current transaction. In the

suspend state, the port is sensitive to resume detection. The bit status

does not change until the port is suspended and there may be a delay in

suspending a port, if there is a transaction currently in progress on the

USB. Attempts to clear this bit are ignored by the Host Controller. The Host

Controller will unconditionally set this bit to logic 0 when:

• Software changes the FPR (Force Port Resume) bit to logic 0

• Software changes the PR (Port Reset) bit to logic 1

If the host software sets this bit when the Port Enabled bit is logic 0, the

results are undeﬁned.^[1]

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

76 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 107. PORTSC 1, 2 - Port Status and Control 1, 2 register bit description …continued

Address: Value read from func2 of address 10h + 64h + (4 × Port Number − 1) where Port Number

is 1, 2

Bit

Symbol Description

6

FPR

Force Port Resume: Logic 1 means resume detected or driven on the

port. Logic 0 means no resume (K-state) detected or driven on the port.

Default = logic 0. Software sets this bit to drive the resume signaling. The

Host Controller sets this bit if a J-to-K transition is detected, while the port

is in the suspend state. When this bit changes to logic 1 because a J-to-K

transition is detected, PCD (bit 2) in the USBSTS register is also set to

logic 1. If software sets this bit to logic 1, the Host Controller must not set

the PCD bit. When the EHCI controller owns the port, the resume

sequence follows the sequence speciﬁed in Universal Serial Bus

Speciﬁcation Rev. 2.0. The resume signaling (full-speed ‘K’) is driven on

the port as long as this bit remains set. Software must time the resume and

clear this bit after the correct amount of time has elapsed. Clearing this bit

causes the port to return to high-speed mode, forcing the bus below the

port into a high-speed idle. This bit will remain at logic 1, until the port has

switched to the high-speed idle. The Host Controller must complete this

transition within 2 ms of software clearing this bit.^[1]

5

4

OCC

OCA

Overcurrent Change: Default = logic 0. This bit is set to logic 1 when

there is a change in overcurrent active. Software clears this bit by setting it

to logic 1.

Overcurrent Active: Default = logic 0. If set to logic 1, this port has an

overcurrent condition. If set to logic 0, this port does not have an

overcurrent condition. This bit will automatically change from logic 1 to

logic 0 when the overcurrent condition is removed.

3

2

PEDC

PED

Port Enable/Disable Change: Logic 1 means the port enabled or disabled

status has changed. Logic 0 means no change. Default = logic 0. For the

root hub, this bit is set only when a port is disabled because of the

appropriate conditions existing at the EOF2 point. For deﬁnition of port

error, refer to Chapter 11 of Universal Serial Bus Speciﬁcation Rev. 2.0.

Software clears this bit by setting it.^[1]

Port Enabled/Disabled: Logic 1 means enable. Logic 0 means disable.

Default = logic 0. Ports can only be enabled by the Host Controller as a

part of the reset and enable sequence. Software cannot enable a port by

writing logic 1 to this ﬁeld. The Host Controller will only set this bit when the

reset sequence determines that the attached device is a high-speed

device. Ports can be disabled by either a fault condition or by host

software. The bit status does not change until the port state has changed.

There may be a delay in disabling or enabling a port because of other Host

Controller and bus events. When the port is disabled, downstream

propagation of data is blocked on this port, except for reset.^[1]

1

ECSC

Connect Status Change: Logic 1 means change in ECCS. Logic 0 means

no change. Default = logic 0. This bit indicates a change has occurred in

the ECCS of the port. The Host Controller sets this bit for all changes to the

port device connect status, even if the system software has not cleared an

existing connect status change. For example, the insertion status changes

two times before the system software has cleared the changed condition,

hub hardware will be setting an already-set bit, that is, the bit will remain

set. Software clears this bit by writing logic 1 to it.^[1]

0

ECCS

Current Connect Status: Logic 1 indicates a device is present on the port.

Logic 0 indicates no device is present. Default = logic 0. This value reﬂects

the current state of the port and may not directly correspond to the event

that caused the ECSC bit to be set.^[1]

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

77 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

[1] These ﬁelds read logic 0, if the PP bit is logic 0.

12. Power consumption

Table 108 shows the power consumption.

Table 108. Power consumption

Power pins group

Conditions

no device connected to the SAF1562HL^[1]

Typ

39

Unit

mA

Total power

V_{CC(I/O)_AUX}+ V_I(VAUX3V3)

+ V_{DDA_AUX}+ V_CC(I/O)

+ V_I(VREG3V3)

one high-speed device connected to the SAF1562HL

two high-speed devices connected to the SAF1562HL

58

76

Auxiliary power

V_{CC(I/O)_AUX}+ V_I(VAUX3V3)

+ V_{DDA_AUX}

no device connected to the SAF1562HL^[1]

26

44

62

13

14

mA

one high-speed device connected to the SAF1562HL

two high-speed devices connected to the SAF1562HL

no device connected to the SAF1562HL^[1]

V_CC(I/O)+ V_I(VREG3V3)

one high-speed device connected to the SAF1562HL

two high-speed devices connected to the SAF1562HL

[1] When one or two full-speed or low-speed power devices are connected, the power consumption is

comparable to the power consumption when no high-speed devices are connected. There is a difference of

approximately 1 mA.

Table 109 shows the power consumption in S1 and S3 suspend modes.

Table 109. Power consumption: S1 and S3

Power state

Typ

20

8^[1][2]

Unit

mA

S1

S3

[1] When I²C-bus is present.

[2] For details, refer to the ISP1562 errata.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

78 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

13. Limiting values

Table 110. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol

Parameter

Conditions

Min

−0.5

0

Max

+4.6

Unit

V

V_CC(I/O)

supply voltage to I/O pins

V_I(VREG3V3)supply voltage to internal regulator

V_{CC(I/O)_AUX}auxiliary supply voltage to I/O pins

V_I(VAUX3V3)auxiliary input voltage to internal regulator

V

V_{DDA_AUX}

V_I(3V3)

I_lu

auxiliary supply voltage for analog block

input voltage on 3.3 V buffers

latch-up current

V

V_CC(I/O)+ 0.5 V V

V_I< 0 V or V_I> V_CC(I/O)

machine model

-

100

mA

[1]

[2]

V_esd

electrostatic discharge voltage

−200

−2000

−40

−55

+200

+2000

+85

V

human body model

V

T_amb

T_stg

ambient temperature

storage temperature

°C

+150

[1] Class B according to EIA/JESD22-A115-A.

[2] Class 2 according to JESD22-A114C.01.

14. Thermal characteristics

Table 111. Thermal characteristics

Symbol

R_th(j-a)

Parameter

Conditions

Typ

40

Unit

K/W

thermal resistance from junction to ambient in free air

thermal resistance from junction to case

R_th(j-c)

12

15. Static characteristics

Table 112. Operating conditions

Symbol

Parameter

Conditions

Min

3.0

Typ

3.3

Max

Unit

V_CC(I/O)

supply voltage to I/O pins

3.6

V

V_I(VREG3V3)supply voltage to internal regulator

V_{CC(I/O)_AUX}auxiliary supply voltage to I/O pins

V_I(VAUX3V3)auxiliary input voltage to internal regulator

V_{DDA_AUX}

auxiliary supply voltage for analog block

Table 113. Static characteristics: I²C-bus interface (SDA and SCL)

V_CC(I/O)= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed.

Symbol

V_IH

Parameter

Conditions

Min

2.1

0

Typ

Max

3.6

0.9

0.4

Unit

V

HIGH-level input voltage

LOW-level input voltage

LOW-level output voltage

-

V_IL

V

V_OL

I_OL= 3 mA

-

V

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

79 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 114. Static characteristics: digital pins

V_CC(I/O)= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed.

Symbol

V_IH

Parameter

Conditions

Min

2.0

0

Typ

Max

3.6

0.8

+10

0.4

-

Unit

V

HIGH-level input voltage

LOW-level input voltage

input leakage current

LOW-level output voltage

HIGH-level output voltage

-

V_IL

V

I_LI

0 V < V_I< V_CC(I/O)

I_OL= 3 mA

−10

-

µA

V

V_OL

V_OH

I_OH= −2 mA

2.4

V

Table 115. Static characteristics: PCI interface block

V_CC(I/O)= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed.

Symbol

V_IH

Parameter

Conditions

Min

Typ

Max

V_CC

0.9

-

Unit

V

HIGH-level input voltage

LOW-level input voltage

input pull-up voltage

input leakage current

HIGH-level output voltage

LOW-level output voltage

input pin capacitance

clock capacitance

0.66V_CC

-

V_IL

0

V

V_IPU

I_LI

2.1

−10

2.7

-

V

0 V < V_I< V_CC(I/O)

I_O= −500 µA

+10

-

µA

V

V_OH

V_OL

I_O= 1500 µA

0.3

10

12

8

V

C_IN

-

pF

C_clk

5

C_IDSEL

IDSEL pin capacitance

-

Table 116. Static characteristics: USB interface block (pins DM1 to DM2 and DP1 to DP2)

V_{DDA_AUX}= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed. Abstract of the USB speciﬁcation rev. 2.0.

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

Input levels for high-speed

V_HSSQ

V_HSDSC

V_HSCM

squelch detection threshold

(differential signal amplitude)

squelch detected

-

100

-

mV

no squelch detected

disconnect detected

disconnect not detected

150

625

-

disconnect detection threshold

(differential signal amplitude)

-

525

+500

data signaling common mode

voltage range

−50

Output levels for high-speed

V_HSOI

idle state

−10

360

−10

700

−900

-

+10

mV

V_HSOH

V_HSOL

V_CHIRPJ

V_CHIRPK

data signaling HIGH

440

data signaling LOW

+10

[1]

Chirp J level (differential voltage)

Chirp K level (differential voltage)

1100

−500

Input levels for full-speed and low-speed

V_IH

HIGH-level input voltage (drive)

HIGH-level input voltage (ﬂoating)

LOW-level input voltage

2.0

2.7

-

V

V_IHZ

V_IL

3.6

0.8

V_DI

differential input sensitivity

|V_DP− V_DM

|

0.2

0.8

-

V_CM

differential common mode range

0.6V_DDA

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

80 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 116. Static characteristics: USB interface block (pins DM1 to DM2 and DP1 to DP2) …continued

V_{DDA_AUX}= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed. Abstract of the USB speciﬁcation rev. 2.0.

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

Output levels for full-speed and low-speed

V_OH

HIGH-level output voltage

LOW-level output voltage

SE1

V

_DDA− 1.1 -

V_DDA

0.3

-

V

V_OL

0

-

V_OSE1

V_CRS

0.8

1.3

output signal crossover point

voltage

2.0

[1] Minimum value: High-speed termination resistor disabled, pull-up resistor connected. Only during reset, when both the hub and device

are capable of high-speed operation.

16. Dynamic characteristics

Table 117. Dynamic characteristics: system clock timing

Symbol

Reset

Parameter

Conditions

Min

Typ

Max

Unit

t_{W(RESET_N)}pulse width on pin RESET_N

crystal oscillator

running

-

10

-

µs

Crystal oscillator

f_clk

PCI clock

31

-

33

MHz

Ω

[1][2]

external clock input

series resistance

load capacitance

crystal

12

-

R_S

C_L

-

100

-

18

pF

External clock input

V_IH

HIGH-level input voltage

0.8V_DDAmin

-

V_DDA

V

V_IL

LOW-level input voltage

external clock jitter

rise time and fall time

clock duty cycle

-

0.2V_DDAmax

V

J

-

50

3

ppm

ns

%

t_CR, t_CF

-

δ

50

-

[1] Recommended accuracy of the clock frequency is 50 ppm for the crystal and oscillator.

[2] Suggested values for external capacitors when using a crystal are 22 pF to 27 pF.

Table 118. Dynamic characteristics: I²C-bus interface (SDA and SCL)

V_CC(I/O)= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed. Abstract of the I²C-bus speciﬁcation rev. 2.1.

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

[1]

t_CF

output fall time V_IHto V_IL

10 < C_b< 400

-

0

250

ns

[1] The capacitive load for each bus line (C_b) is speciﬁed in pF. To meet the speciﬁcation for V_OLand the maximum rise time (300 ns), use

an external pull-up resistor with R_UP(max)= 850 / C_bkΩ and R_UP(min)= (V_CC(I/O)− 0.4) / 3 kΩ.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

81 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 119. Dynamic characteristics: high-speed source electrical characteristics

V_{DDA_AUX}= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed. Abstract of the USB speciﬁcation rev. 2.0.

Symbol Parameter

Driver characteristics

Conditions

Min

Typ

Max

Unit

t_HSR

t_HSF

high-speed differential rise time

high-speed differential fall time

10 % to 90 %

90 % to 10 %

500

40.5

-

ps

Ω

-

Z_HSDRVdrive output resistance; also serves as a

high-speed termination

includes the R_S

resistor

45

49.5

Clock timing

t_HSDRATdata rate

t_HSFRAMmicro frame interval

479.76

124.9375

1

-

480.24

125.0625

-

Mbit/s

µs

[1]

t_HSRFI

consecutive micro frame interval difference

ns

[1] Maximum value: four high-speed bit times.

Table 120. Dynamic characteristics: full-speed source electrical characteristics

V_{DDA_AUX}= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed. Abstract of the USB speciﬁcation rev. 2.0.

Symbol Parameter

Driver characteristics

Conditions

Min

Typ

Max

Unit

t_FR

rise time

C_L= 50 pF;

4

-

20

ns

10 % to 90 % of

|V_OH− V_OL

|

t_FF

fall time

C_L= 50 pF;

4

-

20

ns

90 % to 10 % of

|V_OH− V_OL

|

t_FRFM

differential rise and fall time matching

90

-

111.1

+5

%

Data timing: see Figure 10

t_FDEOP

source jitter for differential transition to

SEO transition

full-speed timing

low-speed timing

−2

ns

t_FEOPT

t_FEOPR

t_LDEOP

source SE0 interval of EOP

receiver SE0 interval of EOP

160

82

-

175

-

ns

source jitter for differential transition to

SEO transition

−40

+100

t_LEOPT

t_LEOPR

t_FST

source SE0 interval of EOP

receiver SE0 interval of EOP

1.25

670

-

1.5

-

µs

ns

width of SE0 interval during the differential

transaction

14

Table 121. Dynamic characteristics: full-speed source electrical characteristics

V_{DDA_AUX}= 3.0 V to 3.6 V; T_amb= −40 °C to +85 °C; unless otherwise speciﬁed. Abstract of the USB speciﬁcation rev. 2.0.

Symbol Parameter

Driver characteristics

Conditions

Min

Typ

Max

Unit

t_LR

rise time

75

90

-

300

125

ns

%

t_LF

fall time

t_LRFM

differential rise and fall time matching

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

82 of 97

SAF1562

NXP Semiconductors

16.1 Timing

Hi-Speed Universal Serial Bus PCI Host Controller

Table 122. PCI clock and IO timing

Abstract of the USB speciﬁcation rev. 2.0.

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

PCI clock timing; see Figure 7

T_cyc(PCICLK)

t_HIGH(PCICLK)

t_LOW(PCICLK)

SR_PCICLK

PCICLK cycle time

PCICLK HIGH time

PCICLK LOW time

PCICLK slew rate

RST# slew rate

30

11

1

-

32

-

ns

-

ns

4

-

V/ns

mV/ns

SR_RST#

50

PCI input timing; see Figure 8

t_su(PCICLK)bs

t_{su(PCICLK)ptp}

t_h(PCICLK)

setup time to PCICLK (bus signal)

7

-

ns

[1]

setup time to PCICLK (point-to-point)

input hold time from PCICLK

10

0

PCI output timing; see Figure 9

t_{val(PCICLK)bs}

t_{val(PCICLK)ptp}

t_dZ(act)

PCICLK to signal valid delay (bus signal)

2

-

11

12

-

ns

PCICLK to signal valid delay (point-to-point)

ﬂoat to active delay

t_d(act)Z

active to ﬂoat delay

28

PCI reset timing

t_rstreset active time after CLK stable

1

-

ms

[1] REQ# and GNT# are point-to-point signals. GNT# has a setup of 10 ns; REQ# has a setup of 12 ns. All others are bus signals.

T

cyc(PCICLK)

t

LOW(PCICLK)

HIGH(PCICLK)

0.6V

0.5V

CC(I/O)

minimum value

0.4V

0.3V

0.2V

CC(I/O)

0.4V

CC(I/O)

004aaa604

Fig 7. PCI clock

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

83 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

0.6V

0.4V

CC(I/O)

CLK

CC(I/O)

0.2V

CC(I/O)

t

;

su(PCICLK)bs

t

h(PCICLK)

su(PCICLK)ptp

0.6V

0.4V

0.2V

CC(I/O)

INPUT

DELAY

inputs valid

004aaa605

Fig 8. PCI input timing

0.6V

0.4V

0.2V

CC(I/O)

CLK

t

;

val(PCICLK)bs

val(PCICLK)ptp

0.615V

(falling edge)

(rising edge)

CC(I/O)

OUTPUT

DELAY

0.285V

CC(I/O)

OUTPUT

t

dZ(act)

t

004aaa606

d(act)Z

Fig 9. PCI output timing

t

USBbit

+3.3 V

crossover point

extended

crossover point

differential

data lines

0 V

(1)

differential data to

SE0/EOP skew

source EOP width: t

EOPT

(1)

receiver EOP width: t

N × t

+ t

EOPR

USBbit

DEOP

008aaa029

t_USBbitis the bit duration (USB data).

t_DEOP^[1]is the source jitter for differential transition to SEO transition.

(1) Full-speed and low-speed timing symbols have a subscript preﬁx ‘F’ and ‘L’, respectively.

Fig 10. USB source differential data-to-EOP transition skew and EOP width

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

84 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

17. Package outline

LQFP100: plastic low profile quad flat package; 100 leads; body 14 x 14 x 1.4 mm

SOT407-1

y

X

A

51

75

50

26

(1)

76

Z

E

e

H

A

E

2

E

A

(A )

3

A

1

w M

p

θ

b

L

p

pin 1 index

L

detail X

100

1

25

Z

D

v

M

A

B

e

w M

b

p

D

B

H

v

M

5

D

0

10 mm

scale

DIMENSIONS (mm are the original dimensions)

A

(1)

UNIT

A

b

c

D

E

e

H

D

H

L

v

w

y

Z

θ

1

2

3

p

E

p

D

E

max.

7^o

0^o

0.15 1.45

0.05 1.35

0.27 0.20 14.1 14.1

0.17 0.09 13.9 13.9

16.25 16.25

15.75 15.75

0.75

0.45

1.15 1.15

0.85 0.85

mm

1.6

0.25

0.5

1

0.2 0.08 0.08

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

REFERENCES

OUTLINE

EUROPEAN

PROJECTION

ISSUE DATE

VERSION

IEC

JEDEC

JEITA

00-02-01

03-02-20

SOT407-1

136E20

MS-026

Fig 11. Package outline SOT407-1 (LQFP100)

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

85 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

18. Soldering

This text provides a very brief insight into a complex technology. A more in-depth account

of soldering ICs can be found in Application Note AN10365 “Surface mount reﬂow

soldering description”.

18.1 Introduction to soldering

Soldering is one of the most common methods through which packages are attached to

Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both

the mechanical and the electrical connection. There is no single soldering method that is

ideal for all IC packages. Wave soldering is often preferred when through-hole and

Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not

suitable for ﬁne pitch SMDs. Reﬂow soldering is ideal for the small pitches and high

densities that come with increased miniaturization.

18.2 Wave and reﬂow soldering

Wave soldering is a joining technology in which the joints are made by solder coming from

a standing wave of liquid solder. The wave soldering process is suitable for the following:

• Through-hole components

• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board

Not all SMDs can be wave soldered. Packages with solder balls, and some leadless

packages which have solder lands underneath the body, cannot be wave soldered. Also,

leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,

due to an increased probability of bridging.

The reﬂow soldering process involves applying solder paste to a board, followed by

component placement and exposure to a temperature proﬁle. Leaded packages,

packages with solder balls, and leadless packages are all reﬂow solderable.

Key characteristics in both wave and reﬂow soldering are:

• Board speciﬁcations, including the board ﬁnish, solder masks and vias

• Package footprints, including solder thieves and orientation

• The moisture sensitivity level of the packages

• Package placement

• Inspection and repair

• Lead-free soldering versus PbSn soldering

18.3 Wave soldering

Key characteristics in wave soldering are:

• Process issues, such as application of adhesive and ﬂux, clinching of leads, board

transport, the solder wave parameters, and the time during which components are

exposed to the wave

• Solder bath speciﬁcations, including temperature and impurities

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

86 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

18.4 Reﬂow soldering

Key characteristics in reﬂow soldering are:

• Lead-free versus SnPb soldering; note that a lead-free reﬂow process usually leads to

higher minimum peak temperatures (see Figure 12) than a PbSn process, thus

reducing the process window

• Solder paste printing issues including smearing, release, and adjusting the process

window for a mix of large and small components on one board

• Reﬂow temperature proﬁle; this proﬁle includes preheat, reﬂow (in which the board is

heated to the peak temperature) and cooling down. It is imperative that the peak

temperature is high enough for the solder to make reliable solder joints (a solder paste

characteristic). In addition, the peak temperature must be low enough that the

packages and/or boards are not damaged. The peak temperature of the package

depends on package thickness and volume and is classiﬁed in accordance with

Table 123 and 124

Table 123. SnPb eutectic process (from J-STD-020C)

Package thickness (mm) Package reﬂow temperature (°C)

Volume (mm³)

< 350

235

≥ 350

220

< 2.5

≥ 2.5

220

Table 124. Lead-free process (from J-STD-020C)

Package thickness (mm) Package reﬂow temperature (°C)

Volume (mm³)

< 350

260

350 to 2000

> 2000

260

< 1.6

260

250

245

1.6 to 2.5

> 2.5

260

245

250

245

Moisture sensitivity precautions, as indicated on the packing, must be respected at all

times.

Studies have shown that small packages reach higher temperatures during reﬂow

soldering, see Figure 12.

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

87 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

maximum peak temperature

= MSL limit, damage level

temperature

minimum peak temperature

= minimum soldering temperature

peak

temperature

time

001aac844

MSL: Moisture Sensitivity Level

Fig 12. Temperature proﬁles for large and small components

For further information on temperature proﬁles, refer to Application Note AN10365

“Surface mount reﬂow soldering description”.

19. Abbreviations

Table 125. Abbreviations

Acronym

CMOS

DID

Description

Complementary Metal-Oxide Semiconductor

Device ID

EEPROM

EHCI

EMI

Electrically Erasable Programmable Read-Only Memory

Enhanced Host Controller Interface

Electro-Magnetic Interference

ElectroStatic Discharge

ESD

HC

Host Controller

HCCA

HCD

Host Controller Communication Area

Host Controller Driver

OHCI

PCI

Open Host Controller Interface

Peripheral Component Interconnect

PCI-Special Interest Group

Phase-Locked Loop

PCI-SIG

PLL

PMC

Power Management Capabilities

Power Management Event

PME

PMCSR

POR

Power Management Control/Status Register

Power-On Reset

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

88 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 125. Abbreviations …continued

Acronym

Description

STB

USB

VID

Set-Top Box

Universal Serial Bus

Vendor ID

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

89 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

20. References

[1] Universal Serial Bus Speciﬁcation Rev. 2.0

[2] Enhanced Host Controller Interface Speciﬁcation for Universal Serial Bus Rev. 1.0

[3] Open Host Controller Interface Speciﬁcation for USB Rev. 1.0a

[4] PCI Local Bus Speciﬁcation Rev. 2.2

[5] PCI Bus Power Management Interface Speciﬁcation Rev. 1.1

[6] The I²C-bus Speciﬁcation, Version 2.1

21. Revision history

Table 126. Revision history

Document ID

Release date

20070207

Data sheet status

Change notice

Supersedes

SAF1562_1

Product data sheet

-

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

90 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

22. Legal information

22.1 Data sheet status

Document status^[1][2]

Product status^[3]

Development

Deﬁnition

Objective [short] data sheet

This document contains data from the objective speciﬁcation for product development.

This document contains data from the preliminary speciﬁcation.

This document contains the product speciﬁcation.

Preliminary [short] data sheet Qualiﬁcation

Product [short] data sheet Production

[1]

[2]

[3]

Please consult the most recently issued document before initiating or completing a design.

The term ‘short data sheet’ is explained in section “Deﬁnitions”.

The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

result in personal injury, death or severe property or environmental damage.

22.2 Deﬁnitions

NXP Semiconductors accepts no liability for inclusion and/or use of NXP

Semiconductors products in such equipment or applications and therefore

such inclusion and/or use is at the customer’s own risk.

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modiﬁcations or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences of

use of such information.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty that such applications will be suitable for the

speciﬁed use without further testing or modiﬁcation.

Limiting values — Stress above one or more limiting values (as deﬁned in

the Absolute Maximum Ratings System of IEC 60134) may cause permanent

damage to the device. Limiting values are stress ratings only and operation of

the device at these or any other conditions above those given in the

Characteristics sections of this document is not implied. Exposure to limiting

values for extended periods may affect device reliability.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is intended

for quick reference only and should not be relied upon to contain detailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local NXP Semiconductors sales

ofﬁce. In case of any inconsistency or conﬂict with the short data sheet, the

full data sheet shall prevail.

Terms and conditions of sale — NXP Semiconductors products are sold

subject to the general terms and conditions of commercial sale, as published

at http://www.nxp.com/proﬁle/terms, including those pertaining to warranty,

intellectual property rights infringement and limitation of liability, unless

explicitly otherwise agreed to in writing by NXP Semiconductors. In case of

any inconsistency or conﬂict between information in this document and such

terms and conditions, the latter will prevail.

22.3 Disclaimers

General — Information in this document is believed to be accurate and

reliable. However, NXP Semiconductors does not give any representations or

warranties, expressed or implied, as to the accuracy or completeness of such

information and shall have no liability for the consequences of use of such

information.

No offer to sell or license — Nothing in this document may be interpreted

or construed as an offer to sell products that is open for acceptance or the

grant, conveyance or implication of any license under any copyrights, patents

or other industrial or intellectual property rights.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation speciﬁcations and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

22.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks

are the property of their respective owners.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in medical, military, aircraft,

space or life support equipment, nor in applications where failure or

malfunction of a NXP Semiconductors product can reasonably be expected to

I²C-bus — logo is a trademark of NXP B.V.

23. Contact information

For additional information, please visit: http://www.nxp.com

For sales ofﬁce addresses, send an email to: salesaddresses@nxp.com

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

91 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

24. Tables

Table 1. Ordering information . . . . . . . . . . . . . . . . . . . . .2

Table 2. Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5

Table 3. PCI conﬁguration space registers of

OHCI1, OHCI2 and EHCI . . . . . . . . . . . . . . . .12

Table 4. VID - Vendor ID register (address 00h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .14

Table 5. DID - Device ID register (address 02h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .14

Table 6. Command register (address 04h)

bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Table 7. Command register (address 04h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .15

Table 8. Status register (address 06h) bit allocation . . .16

Table 9. Status register (address 06h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .16

Table 10. REVID - Revision ID register (address 08h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .17

Table 11. Class Code register (address 09h)

bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Table 12. Class Code register (address 09h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .18

Table 13. CLS - Cache Line Size register

(address 0Ch) bit description . . . . . . . . . . . . . .19

Table 14. LT - Latency Timer register (address 0Dh)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .19

Table 15. Header Type register (address 0Eh)

bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Table 16. Header Type register (address 0Eh) bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Table 17. BAR 0 - Base Address register 0

(address 10h) bit description . . . . . . . . . . . . . .20

Table 18. SVID - Subsystem Vendor ID register

(address 2Ch) bit description . . . . . . . . . . . . . .20

Table 19. SID - Subsystem ID register (address 2Eh)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .20

Table 20. CP - Capabilities Pointer register

(address 34h) bit description . . . . . . . . . . . . . .20

Table 21. IL - Interrupt Line register (address 3Ch)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .21

Table 22. IP - Interrupt Pin register (address 3Dh)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .21

Table 23. Min_Gnt - Minimum Grant register

(address 3Eh) bit description . . . . . . . . . . . . . .21

Table 24. Max_Lat - Maximum Latency register

(address 3Fh) bit description . . . . . . . . . . . . . .22

Table 25. EHCI-speciﬁc PCI registers . . . . . . . . . . . . . . .22

Table 26. SBRN - Serial Bus Release Number

register (address 60h) bit description . . . . . . .23

Table 27. FLADJ - Frame Length Adjustment

register (address 61h) bit allocation . . . . . . . . 23

Table 28. FLADJ - Frame Length Adjustment

register (address 61h) bit description . . . . . . . 23

Table 29. PORTWAKECAP - Port Wake Capability

register (address 62h) bit description . . . . . . . 24

Table 30. Power Management registers . . . . . . . . . . . . . 24

Table 31. Cap_ID - Capability Identiﬁer register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Table 32. Next_Item_Ptr - Next Item Pointer register

bit description . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table 33. PMC - Power Management Capabilities

register bit allocation . . . . . . . . . . . . . . . . . . . . 25

Table 34. PMC - Power Management Capabilities

register bit description . . . . . . . . . . . . . . . . . . . 25

Table 35. PMCSR - Power Management

Control/Status register bit allocation . . . . . . . . 27

Table 36. PMCSR - Power Management

Control/Status register bit description . . . . . . . 27

Table 37. PMCSR_BSE - PMCSR PCI-to-PCI

Bridge Support Extensions register

bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 38. PMCSR_BSE - PMCSR PCI-to-PCI

Bridge Support Extensions register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 39. PCI bus power and clock control . . . . . . . . . . . 29

Table 40. Data register bit description . . . . . . . . . . . . . . 29

Table 41. USB Host Controller registers . . . . . . . . . . . . . 32

Table 42. HcRevision - Host Controller Revision

register bit allocation . . . . . . . . . . . . . . . . . . . . 33

Table 43. HcRevision - Host Controller Revision

register bit description . . . . . . . . . . . . . . . . . . . 34

Table 44. HcControl - Host Controller Control

register bit allocation . . . . . . . . . . . . . . . . . . . . 34

Table 45. HcControl - Host Controller Control

register bit description . . . . . . . . . . . . . . . . . . . 35

Table 46. HcCommandStatus - Host Controller

Command Status register bit allocation . . . . . 37

Table 47. HcCommandStatus - Host Controller

Command Status register bit description . . . . 37

Table 48. HcInterruptStatus - Host Controller

Interrupt Status register bit allocation . . . . . . . 38

Table 49. HcInterruptStatus - Host Controller

Interrupt Status register bit description . . . . . . 39

Table 50. HcInterruptEnable - Host Controller

Interrupt Enable register bit allocation . . . . . . . 40

Table 51. HcInterruptEnable - Host Controller

Interrupt Enable register bit description . . . . . 40

continued >>

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

92 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 52. HcInterruptDisable - Host Controller

Interrupt Disable register bit allocation . . . . . .41

Table 53. HcInterruptDisable - Host Controller

Interrupt Disable register bit description . . . . .42

Table 54. HcHCCA - Host Controller Communication

Area register bit allocation . . . . . . . . . . . . . . . .43

Table 55. HcHCCA - Host Controller Communication

Area register bit description . . . . . . . . . . . . . . .43

Table 56. HcPeriodCurrentED - Host Controller

Period Current Endpoint Descriptor

register bit allocation . . . . . . . . . . . . . . . . . . . .44

Table 57. HcPeriodCurrentED - Host Controller

Period Current Endpoint Descriptor

register bit description . . . . . . . . . . . . . . . . . . .44

Table 58. HcControlHeadED - Host Controller Control

Head Endpoint Descriptor register bit

allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Table 59. HcControlHeadED - Host Controller Control

Head Endpoint Descriptor register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Table 60. HcControlCurrentED - Host Controller

Control Current Endpoint Descriptor

register bit allocation . . . . . . . . . . . . . . . . . . . .45

Table 61. HcControlCurrentED - Host Controller

Control Current Endpoint Descriptor

Number register bit allocation . . . . . . . . . . . . . 50

Table 73. HcFmNumber - Host Controller Frame

Number register bit description . . . . . . . . . . . . 51

Table 74. HcPeriodicStart - Host Controller Periodic

Start register bit allocation . . . . . . . . . . . . . . . 51

Table 75. HcPeriodicStart - Host Controller Periodic

Start register bit description . . . . . . . . . . . . . . 52

Table 76. HcLSThreshold - Host Controller

LS Threshold register bit allocation . . . . . . . . . 52

Table 77. HcLSThreshold - Host Controller

LS Threshold register bit description . . . . . . . . 52

Table 78. HcRhDescriptorA - Host Controller Root

Hub Descriptor A register bit allocation . . . . . . 53

Table 79. HcRhDescriptorA - Host Controller Root

Hub Descriptor A register bit description . . . . . 53

Table 80. HcRhDescriptorB - Host Controller Root

Hub Descriptor B register bit allocation . . . . . . 54

Table 81. HcRhDescriptorB - Host Controller Root

Hub Descriptor B register bit description . . . . . 55

Table 82. HcRhStatus - Host Controller Root Hub

Status register bit allocation . . . . . . . . . . . . . . 55

Table 83. HcRhStatus - Host Controller Root Hub

Status register bit description . . . . . . . . . . . . . 56

Table 84. HcRhPortStatus[4:1] - Host Controller

Root Hub Port Status[4:1] register bit

register bit description . . . . . . . . . . . . . . . . . . .46

Table 62. HcBulkHeadED - Host Controller Bulk

Head Endpoint Descriptor register bit

allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 85. HcRhPortStatus[4:1] - Host Controller

Root Hub Port Status[4:1] register bit

allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 63. HcBulkHeadED - Host Controller Bulk

Head Endpoint Descriptor register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 86. CAPLENGTH/HCIVERSION - Capability

Registers Length/Host Controller

description . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 64. HcBulkCurrentED - Host Controller Bulk

Current Endpoint Descriptor register bit

allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Table 65. HcBulkCurrentED - Host Controller Bulk

Current Endpoint Descriptor register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Table 66. HcDoneHead - Host Controller Done Head

register bit allocation . . . . . . . . . . . . . . . . . . . .48

Table 67. HcDoneHead - Host Controller Done Head

register bit description . . . . . . . . . . . . . . . . . . .48

Table 68. HcFmInterval - Host Controller Frame

Interval register bit allocation . . . . . . . . . . . . . .48

Table 69. HcFmInterval - Host Controller Frame

Interval register bit description . . . . . . . . . . . . .49

Table 70. HcFmRemaining - Host Controller Frame

Remaining register bit allocation . . . . . . . . . . .49

Table 71. HcFmRemaining - Host Controller Frame

Remaining register bit description . . . . . . . . . .50

Table 72. HcFmNumber - Host Controller Frame

Interface Version Number register

bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Table 87. CAPLENGTH/HCIVERSION - Capability

Registers Length/Host Controller

Interface Version Number register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Table 88. HCSPARAMS - Host Controller

Structural Parameters register bit allocation . . 61

Table 89. HCSPARAMS - Host Controller

Structural Parameters register bit description . 62

Table 90. HCCPARAMS - Host Controller

Capability Parameters register bit allocation . . 63

Table 91. HCCPARAMS - Host Controller Capability

Parameters register bit description . . . . . . . . . 63

Table 92. USBCMD - USB Command register bit

allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Table 93. USBCMD - USB Command register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Table 94. USBSTS - USB Status register bit

allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

continued >>

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

93 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

Table 95. USBSTS - USB Status register bit

Table 124.Lead-free process (from J-STD-020C) . . . . . . 87

Table 125.Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Table 126.Revision history . . . . . . . . . . . . . . . . . . . . . . . . 90

description . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Table 96. USBINTR - USB Interrupt Enable register

bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Table 97. USBINTR - USB Interrupt Enable register

bit description . . . . . . . . . . . . . . . . . . . . . . . . .69

Table 98. FRINDEX - Frame Index register bit

allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Table 99. FRINDEX - Frame Index register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Table 100.PERIODICLISTBASE - Periodic Frame

List Base Address register bit allocation . . . . .71

Table 101.PERIODICLISTBASE - Periodic Frame

List Base Address register bit description . . . .72

Table 102.ASYNCLISTADDR - Current

Asynchronous List Address register bit

allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Table 103.ASYNCLISTADDR - Current

Asynchronous List Address register bit

description . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Table 104.CONFIGFLAG - Conﬁgure Flag register

bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Table 105.CONFIGFLAG - Conﬁgure Flag register

bit description . . . . . . . . . . . . . . . . . . . . . . . . .73

Table 106.PORTSC 1, 2 - Port Status and Control 1, 2

register bit allocation . . . . . . . . . . . . . . . . . . . .74

Table 107.PORTSC 1, 2 - Port Status and Control 1, 2

register bit description . . . . . . . . . . . . . . . . . . .74

Table 108.Power consumption . . . . . . . . . . . . . . . . . . . . .78

Table 109.Power consumption: S1 and S3 . . . . . . . . . . . .78

Table 110.Limiting values . . . . . . . . . . . . . . . . . . . . . . . . .79

Table 111.Thermal characteristics . . . . . . . . . . . . . . . . . .79

Table 112.Operating conditions . . . . . . . . . . . . . . . . . . . .79

Table 113.Static characteristics: I²C-bus interface

(SDA and SCL) . . . . . . . . . . . . . . . . . . . . . . . .79

Table 114.Static characteristics: digital pins . . . . . . . . . . .80

Table 115.Static characteristics: PCI interface block . . . .80

Table 116.Static characteristics: USB interface block

(pins DM1 to DM2 and DP1 to DP2) . . . . . . . .80

Table 117.Dynamic characteristics: system

clock timing . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Table 118.Dynamic characteristics: I²C-bus interface

(SDA and SCL) . . . . . . . . . . . . . . . . . . . . . . . .81

Table 119.Dynamic characteristics: high-speed

source electrical characteristics . . . . . . . . . . . .82

Table 120.Dynamic characteristics: full-speed

source electrical characteristics . . . . . . . . . . . .82

Table 121.Dynamic characteristics: full-speed

source electrical characteristics . . . . . . . . . . . .82

Table 122.PCI clock and IO timing . . . . . . . . . . . . . . . . . .83

Table 123.SnPb eutectic process (from J-STD-020C) . . .87

continued >>

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

94 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

25. Figures

Fig 1. Block diagram of SAF1562HL . . . . . . . . . . . . . . . .3

Fig 2. Pin conﬁguration for LQFP100. . . . . . . . . . . . . . . .4

Fig 3. Power-on reset. . . . . . . . . . . . . . . . . . . . . . . . . . .10

Fig 4. Power supply connection . . . . . . . . . . . . . . . . . . .11

Fig 5. EEPROM connection diagram. . . . . . . . . . . . . . .30

Fig 6. Information loading from EEPROM . . . . . . . . . . .31

Fig 7. PCI clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Fig 8. PCI input timing . . . . . . . . . . . . . . . . . . . . . . . . . .84

Fig 9. PCI output timing . . . . . . . . . . . . . . . . . . . . . . . . .84

Fig 10. USB source differential data-to-EOP transition

skew and EOP width . . . . . . . . . . . . . . . . . . . . . .84

Fig 11. Package outline SOT407-1 (LQFP100) . . . . . . . .85

Fig 12. Temperature proﬁles for large and small

components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

continued >>

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

95 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

26. Contents

1

2

3

4

5

General description . . . . . . . . . . . . . . . . . . . . . . 1

8.2.3

Power management registers. . . . . . . . . . . . . 24

Cap_ID register . . . . . . . . . . . . . . . . . . . . . . . 24

Next_Item_Ptr register . . . . . . . . . . . . . . . . . . 24

PMC register . . . . . . . . . . . . . . . . . . . . . . . . . 25

PMCSR register . . . . . . . . . . . . . . . . . . . . . . . 26

PMCSR_BSE register . . . . . . . . . . . . . . . . . . 28

Data register. . . . . . . . . . . . . . . . . . . . . . . . . . 29

I²C-bus interface . . . . . . . . . . . . . . . . . . . . . . . 30

Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Hardware connections . . . . . . . . . . . . . . . . . . 30

Information loading from EEPROM . . . . . . . . 31

8.2.3.1

8.2.3.2

8.2.3.3

8.2.3.4

8.2.3.5

8.2.3.6

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Ordering information. . . . . . . . . . . . . . . . . . . . . 2

Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3

6

6.1

6.2

Pinning information. . . . . . . . . . . . . . . . . . . . . . 4

Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5

9

9.1

9.2

9.3

7

Functional description . . . . . . . . . . . . . . . . . . . 9

OHCI Host Controller . . . . . . . . . . . . . . . . . . . . 9

EHCI Host Controller . . . . . . . . . . . . . . . . . . . . 9

Dynamic port-routing logic . . . . . . . . . . . . . . . . 9

Hi-Speed USB analog transceivers . . . . . . . . 10

Power management . . . . . . . . . . . . . . . . . . . . 10

Phase-Locked Loop (PLL) . . . . . . . . . . . . . . . 10

Power-On Reset (POR) . . . . . . . . . . . . . . . . . 10

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.1

7.2

7.3

7.4

7.5

7.6

7.7

7.8

10

10.1

10.2

Power management. . . . . . . . . . . . . . . . . . . . . 31

PCI bus power states . . . . . . . . . . . . . . . . . . . 31

USB bus states . . . . . . . . . . . . . . . . . . . . . . . 32

11

11.1

USB Host Controller registers . . . . . . . . . . . . 32

OHCI USB Host Controller operational

registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

HcRevision register . . . . . . . . . . . . . . . . . . . . 33

HcControl register . . . . . . . . . . . . . . . . . . . . . 34

HcCommandStatus register. . . . . . . . . . . . . . 36

HcInterruptStatus register . . . . . . . . . . . . . . . 38

HcInterruptEnable register . . . . . . . . . . . . . . . 40

HcInterruptDisable register . . . . . . . . . . . . . . 41

HcHCCA register . . . . . . . . . . . . . . . . . . . . . . 43

HcPeriodCurrentED register. . . . . . . . . . . . . . 43

HcControlHeadED register. . . . . . . . . . . . . . . 44

11.1.1

11.1.2

11.1.3

11.1.4

11.1.5

11.1.6

11.1.7

11.1.8

11.1.9

8

8.1

8.1.1

8.1.2

8.2

8.2.1

8.2.1.1

8.2.1.2

8.2.1.3

8.2.1.4

8.2.1.5

8.2.1.6

8.2.1.7

8.2.1.8

8.2.1.9

PCI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

PCI interface. . . . . . . . . . . . . . . . . . . . . . . . . . 11

PCI conﬁguration space . . . . . . . . . . . . . . . . . 12

PCI initiator and target . . . . . . . . . . . . . . . . . . 12

PCI conﬁguration registers . . . . . . . . . . . . . . . 12

PCI conﬁguration header registers . . . . . . . . . 13

Vendor ID register. . . . . . . . . . . . . . . . . . . . . . 13

Device ID register . . . . . . . . . . . . . . . . . . . . . . 14

Command register . . . . . . . . . . . . . . . . . . . . . 14

Status register. . . . . . . . . . . . . . . . . . . . . . . . . 16

Revision ID register . . . . . . . . . . . . . . . . . . . . 17

Class Code register . . . . . . . . . . . . . . . . . . . . 17

Cache Line Size register. . . . . . . . . . . . . . . . . 18

Latency Timer register . . . . . . . . . . . . . . . . . . 19

Header Type register . . . . . . . . . . . . . . . . . . . 19

11.1.10 HcControlCurrentED register . . . . . . . . . . . . . 45

11.1.11 HcBulkHeadED register . . . . . . . . . . . . . . . . . 46

11.1.12 HcBulkCurrentED register . . . . . . . . . . . . . . . 47

11.1.13 HcDoneHead register. . . . . . . . . . . . . . . . . . . 47

11.1.14 HcFmInterval register. . . . . . . . . . . . . . . . . . . 48

11.1.15 HcFmRemaining register . . . . . . . . . . . . . . . . 49

11.1.16 HcFmNumber register . . . . . . . . . . . . . . . . . . 50

11.1.17 HcPeriodicStart register . . . . . . . . . . . . . . . . . 51

11.1.18 HcLSThreshold register . . . . . . . . . . . . . . . . . 52

11.1.19 HcRhDescriptorA register . . . . . . . . . . . . . . . 53

11.1.20 HcRhDescriptorB register . . . . . . . . . . . . . . . 54

11.1.21 HcRhStatus register. . . . . . . . . . . . . . . . . . . . 55

11.1.22 HcRhPortStatus[4:1] register . . . . . . . . . . . . . 57

8.2.1.10 Base Address register 0 . . . . . . . . . . . . . . . . . 19

8.2.1.11 Subsystem Vendor ID register . . . . . . . . . . . . 20

8.2.1.12 Subsystem ID register . . . . . . . . . . . . . . . . . . 20

8.2.1.13 Capabilities Pointer register . . . . . . . . . . . . . . 20

8.2.1.14 Interrupt Line register . . . . . . . . . . . . . . . . . . . 21

8.2.1.15 Interrupt Pin register. . . . . . . . . . . . . . . . . . . . 21

8.2.1.16 Min_Gnt and Max_Lat registers . . . . . . . . . . . 21

8.2.1.17 TRDY time-out register . . . . . . . . . . . . . . . . . . 22

8.2.1.18 Retry time-out register . . . . . . . . . . . . . . . . . . 22

11.2

EHCI controller capability registers . . . . . . . . 60

CAPLENGTH/HCIVERSION register. . . . . . . 60

HCSPARAMS register . . . . . . . . . . . . . . . . . . 61

HCCPARAMS register . . . . . . . . . . . . . . . . . . 63

HCSP-PORTROUTE register. . . . . . . . . . . . . 64

Operational registers of Enhanced

11.2.1

11.2.2

11.2.3

11.2.4

11.3

8.2.2

Enhanced Host Controller-speciﬁc

PCI registers. . . . . . . . . . . . . . . . . . . . . . . . . . 22

SBRN register. . . . . . . . . . . . . . . . . . . . . . . . . 22

FLADJ register . . . . . . . . . . . . . . . . . . . . . . . . 23

PORTWAKECAP register. . . . . . . . . . . . . . . . 23

8.2.2.1

8.2.2.2

8.2.2.3

USB Host Controller. . . . . . . . . . . . . . . . . . . . 64

USBCMD register. . . . . . . . . . . . . . . . . . . . . . 64

11.3.1

continued >>

SAF1562_1

Product data sheet

Rev. 01 — 7 February 2007

96 of 97

SAF1562

NXP Semiconductors

Hi-Speed Universal Serial Bus PCI Host Controller

11.3.2

11.3.3

11.3.4

11.3.5

11.3.6

11.3.7

11.3.8

USBSTS register . . . . . . . . . . . . . . . . . . . . . . 66

USBINTR register. . . . . . . . . . . . . . . . . . . . . . 68

FRINDEX register. . . . . . . . . . . . . . . . . . . . . . 70

PERIODICLISTBASE register . . . . . . . . . . . . 71

ASYNCLISTADDR register. . . . . . . . . . . . . . . 72

CONFIGFLAG register . . . . . . . . . . . . . . . . . . 73

PORTSC registers 1, 2. . . . . . . . . . . . . . . . . . 74

12

Power consumption. . . . . . . . . . . . . . . . . . . . . 78

Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 79

Thermal characteristics. . . . . . . . . . . . . . . . . . 79

Static characteristics. . . . . . . . . . . . . . . . . . . . 79

Dynamic characteristics . . . . . . . . . . . . . . . . . 81

Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Package outline . . . . . . . . . . . . . . . . . . . . . . . . 85

13

14

15

16

16.1

17

18

Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Introduction to soldering . . . . . . . . . . . . . . . . . 86

Wave and reﬂow soldering . . . . . . . . . . . . . . . 86

Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 86

Reﬂow soldering . . . . . . . . . . . . . . . . . . . . . . . 87

18.1

18.2

18.3

18.4

19

20

21

Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 88

References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Revision history. . . . . . . . . . . . . . . . . . . . . . . . 90

22

Legal information. . . . . . . . . . . . . . . . . . . . . . . 91

Data sheet status . . . . . . . . . . . . . . . . . . . . . . 91

Deﬁnitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 91

22.1

22.2

22.3

22.4

23

24

25

26

Contact information. . . . . . . . . . . . . . . . . . . . . 91

Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 7 February 2007

Document identifier: SAF1562_1


型号：	SAF1562HL/N2,518
厂家：	NXP
描述：	SAF1562 - Hi-Speed Universal Serial Bus PCI Host Controller QFP 100-Pin 时钟 PC 外围集成电路
文件：	总97页 (文件大小：395K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SAF1562HL/N2,518 [NXP]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E