SSTUM32865EG [NXP]
1.8 V 28-bit 1 : 2 registered buffer with parity for DDR2-800 RDIMM applications; 1.8 V 28位1 : 2注册奇偶校验的DDR2-800 RDIMM应用程序的缓冲区![SSTUM32865EG](http://pdffile.icpdf.com/pdf1/p00121/img/icpdf/SSTUM32865_669259_icpdf.jpg)
型号: | SSTUM32865EG |
厂家: | ![]() |
描述: | 1.8 V 28-bit 1 : 2 registered buffer with parity for DDR2-800 RDIMM applications |
文件: | 总28页 (文件大小:153K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
SSTUM32865
1.8 V 28-bit 1 : 2 registered buffer with parity for DDR2-800
RDIMM applications
Rev. 01 — 19 September 2007
Product data sheet
1. General description
The SSTUM32865 is a 1.8 V 28-bit 1 : 2 register specifically designed for use on two rank
by four (2R × 4) and similar high-density Double Data Rate 2 (DDR2) memory modules. It
is similar in function to the JEDEC-standard 14-bit DDR2 register, but integrates the
functionality of the normally required two registers in a single package, thereby freeing up
board real-estate and facilitating routing to accommodate high-density Dual In-line
Memory Module (DIMM) designs.
The SSTUM32865 also integrates a parity function, which accepts a parity bit from the
memory controller, compares it with the data received on the D-inputs and indicates
whether a parity error has occurred on its open-drain PTYERR pin (active LOW).
It further offers added features over the JEDEC standard register in that it is permanently
configured for high output drive strength. This allows use in high density designs with
heavier than normal net loading conditions. Furthermore, the SSTUM32865 features two
additional chip select inputs, which allow more versatile enabling and disabling in densely
populated memory modules. Both added features (drive strength and chip selects) are
fully backward compatible to the JEDEC standard register.
The SSTUM32865 is packaged in a 160-ball, 12 × 18 grid, 0.65 mm ball pitch, thin profile
fine-pitch ball grid array (TFBGA) package, which, while requiring a minimum
9 mm × 13 mm of board space, allows for adequate signal routing and escape using
conventional card technology.
2. Features
I 28-bit data register supporting DDR2
I Fully compliant to JEDEC standard for SSTUB32865
I Supports 2 rank by 4 DIMM density by integrating equivalent functionality of two
JEDEC-standard DDR2 registers (that is, 2 × SSTUB32864 or 2 × SSTUB32866)
I Parity checking function across 22 input data bits
I Parity out signal
I Controlled multi-impedance output impedance drivers enable optimal signal integrity
and speed
I Meets or exceeds SSTUB32865 JEDEC standard speed performance
I Supports up to 450 MHz clock frequency of operation
I Permanently configured for high output drive
I Optimized pinout for high-density DDR2 module design
I Chip-selects minimize power consumption by gating data outputs from changing state
I Two additional chip select inputs allow optional flexible enabling and disabling
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
I Supports Stub Series Terminated Logic SSTL_18 data inputs
I Differential clock (CK and CK) inputs
I Supports LVCMOS switching levels on the control and RESET inputs
I Single 1.8 V supply operation (1.7 V to 2.0 V)
I Available in 160-ball 9 mm × 13 mm, 0.65 mm ball pitch TFBGA package
3. Applications
I 400 MT/s to 800 MT/s high-density (for example, 2 rank by 4) DDR2 registered DIMMs
I DDR2 Registered DIMMs (RDIMM) desiring parity checking functionality
4. Ordering information
Table 1.
Ordering information
Solder process
Type number
Package
Name
Description
Version
SSTUM32865ET/G Pb-free (SnAgCu solder ball TFBGA160 plastic thin fine-pitch ball grid array package; SOT802-2
compound) 160 balls; body 9 × 13 × 0.7 mm
SSTUM32865ET/S Pb-free (SnAgCu solder ball TFBGA160 plastic thin fine-pitch ball grid array package; SOT802-2
compound)
160 balls; body 9 × 13 × 0.7 mm
4.1 Ordering options
Table 2.
Ordering options
Type number
SSTUM32865ET/G
SSTUM32865ET/S
Topside mark
Temperature range
SSTUM32865ET
SSTUM32865ETS
Tamb = 0 °C to +70 °C
Tamb = 0 °C to +85 °C
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
2 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
5. Functional diagram
(CS ACTIVE)
VREF
SSTUM32865
PARITY
GENERATOR
AND
CHECKER
D
Q
Q
Q
Q
Q
PARIN
22
PTYERR
R
Q0A
D
R
D0
Q0B
Q21A
Q21B
D
R
D21
QCS0A
QCS0B
DCS0
D
R
CSGATEEN
DCS1
QCS1A
QCS1B
D
R
DCS2
DCS3
QCKE0A,
QCKE1A
DCKE0,
2
2
2
D
R
Q
Q
DCKE1
QCKE0B,
QCKE1B
QODT0A,
QODT1A
DODT0,
2
DODT1
D
R
QODT0B,
QODT1B
RESET
CK
CK
002aac647
Fig 1. Functional diagram of SSTUM32865
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
3 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
6. Pinning information
6.1 Pinning
SSTUM32865ET/G
SSTUM32865ET/S
ball A1
index area
2
4
6
8
10 12
9 11
1
3
5
7
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
002aac648
Transparent top view
Fig 2. Pin configuration for TFBGA160
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
4 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
1
VREF
D1
2
n.c.
3
4
5
6
7
8
9
10
11
12
A
B
C
D
E
F
PARIN
n.c.
n.c.
n.c.
n.c.
n.c.
QCKE1A QCKE0A
QCKE1B QCKE0B
Q21A
Q21B
Q19A
Q19B
Q18A
Q18B
Q17B
Q17A
D2
QODT0B QODT0A
QODT1B QODT1A
D3
D4
D6
D5
VDDL
VDDL
VDDL
VDDL
DCS2
GND
GND
GND
GND
GND
GND
GND
VDDL
GND
GND
VDDL
VDDL
VDDL
n.c.
n.c.
GND
GND
GND
GND
Q20B
Q16B
Q1B
Q20A
Q16A
Q1A
D7
D8
VDDL
VDDR
D11
D9
VDDR
VDDR
GND
VDDR
VDDR
GND
D18
D12
D15
DCS0
DCS1
D14
D10
D16
D21
D20
DODT0
DCKE1
MCL
Q2B
Q2A
G
H
J
CSGATEEN
CK
Q5B
Q5A
VDDR
GND
VDDR
GND
QCS0B
QCS1B
Q6B
QCS0A
QCS1A
Q6A
CK
DCS3
GND
K
L
RESET
D0
VDDR
GND
VDDR
GND
GND
Q10B
Q9B
Q10A
Q9A
M
N
P
R
T
D17
VDDL
GND
VDDR
VDDR
GND
VDDR
GND
D19
VDDL
VDDL
VDDR
GND
Q11B
Q15B
Q14B
Q0B
Q11A
Q15A
Q14A
Q8B
D13
GND
GND
DODT1
DCKE0
VREF
MCL
MCL
PTYERR
n.c.
MCH
MCH
Q3B
Q3A
Q12B
Q12A
Q7B
Q7A
Q4B
Q4A
Q13B
Q13A
U
V
Q0A
Q8A
002aac650
160-ball, 12 × 18 grid; top view.
An empty cell indicates no ball is populated at that grid point.
n.c. denotes a no-connect (ball present but not connected to the die).
MCL denotes a pin that must be connected LOW.
MCH denotes a pin that must be connected HIGH.
Fig 3. Ball mapping
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
5 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
6.2 Pin description
Table 3.
Pin description
Symbol
Pin
Type
Description
Ungated inputs
DCKE0, DCKE1
DODT0, DODT1
U1, U2
T2, T1
SSTL_18
DRAM function pins not associated with Chip Select.
DRAM inputs, re-driven only when Chip Select is LOW.
Chip Select gated inputs
D0 to D21
M1, B1, B2, C1, C2, D2, D1, SSTL_18
E1, E2, F2, M2, F1, G2, R1,
L2, H2, N2, N1, G1, P1, R2,
P2
Chip Select inputs
DCS0, DCS1,
DCS2, DCS3[1]
J2, K2, H4, K4
SSTL_18
DRAM Chip Select signals. These pins initiate DRAM
address/command decodes, and as such at least one will
be LOW when a valid address/command is present. The
register can be programmed to re-drive all D-inputs only
(CSGATEEN = HIGH) when at least one Chip Select
input is LOW. DCS2 and DCS3 are not re-driven and can
be left open-circuit to default HIGH by means of its
internal pull-up resistors.
Re-driven outputs
Q0A to Q21A
V11, F12, G12, V6, V9, H12, SSTL_18
L12, V8, V12, N12, M12,
P12, V7, V10, T12, R12,
Outputs of the register, valid after the specified clock
count and immediately following a rising edge of the
clock.
E12, A12, A10, A9, D12, A8
Q0B to Q21B
U11, F11, G11, U6, U9,
H11, L11, U8, U12, N11,
M11, P11, U7, U10, T11,
R11, E11, A11, B10, B9,
D11, B8
QCS0A, QDS1A,
QCS0B, QCS1B
J12, K12, J11, K11
QCKE0A, QCKE1A, A7, A6, B7, B6
QCKE0B, QCKE1B
QODT0A, QODT1A, B12, C12, B11, C11
QODT0B, QODT1B
Parity input
PARIN
A3
U4
SSTL_18
Parity input for the D0 to D21 inputs. Arrives one clock
cycle after the corresponding data input.
Parity error
PTYERR
open-drain When LOW, this output indicates that a parity error was
identified associated with the address and/or command
inputs. PTYERR will be active for two clock cycles, and
delayed by an additional clock cycle for compatibility with
final parity out timing on the industry-standard DDR2
register with parity (in JEDEC definition).
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
6 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
Program inputs
CSGATEEN
H1
1.8 V
LVCMOS
Chip Select Gate Enable. When HIGH, the D0 to D21
inputs will be latched only when at least one Chip Select
with weak input is LOW during the rising edge of the clock. When
pull-up
LOW, the D0 to D21 inputs will be latched and redriven
on every rising edge of the clock.
Clock inputs
CK, CK
J1, K1
SSTL_18
Differential master clock input pair to the register. The
register operation is triggered by a rising edge on the
positive clock input (CK).
Miscellaneous inputs
MCL
U3, V2, V3
U5, V5
L1
Must be connected to a logic LOW.
Must be connected to a logic HIGH.
MCH
RESET
1.8 V
LVCMOS
Asynchronous reset input. When LOW, it causes a reset
of the internal latches, thereby forcing the outputs LOW.
with weak RESET also resets the PTYERR signal.
pull-up
VREF
VDDL
VDDR
GND
A1, V1
0.9 V
nominal
Input reference voltage for the SSTL_18 inputs. Two pins
(internally tied together) are used for increased reliability.
D4, E4, E6, F4, G4, K5, N4,
N5, P5, P6, R5, R6
Power supply voltage.
Power supply voltage.
Ground.
E7, F8, F9, G8, G9, J8, J9,
L8, L9, N8, N9, P7, P8
D5, D8, D9, E5, E8, E9, F5,
G5, H5, H8, H9, J4, J5, K8,
K9, L4, L5, M4, M5, M8, M9,
P4, P9, R4, R7, R8, R9
n.c.
A2, A4, A5, B3, B4, B5, D6,
D7, V4
Ball present but not connected to die.
[1] If application does not require DCS2 and DCS3, it is allowed to connect H4 and K4 to VDD
.
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
7 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
7. Functional description
7.1 Function table
Table 4.
Function table (each flip-flop)
Inputs
RESET DCS0[2] DCS1[2] CSGATEEN
Outputs[1]
CK
CK
Dn, DODTn, DCKEn Qn QCS0 QCS1 QODTn,
QCKEn
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
L
L
L
L
X
↑
↓
L
L
H
L
L
L
L
L
H
X
↑
↓
H
L
L
X
L or H
L or H
X
Q0
L
Q0
L
Q0
H
Q0
L
L
H
H
H
L
X
↑
↓
L
L
X
↑
↓
H
H
L
H
H
L
X
L or H
L or H
X
Q0
L
Q0
H
Q0
L
Q0
L
H
H
H
H
H
H
H
H
H
X or
X
↑
↓
L
L
X
↑
L or H
↑
↓
L or H
↓
H
H
H
L
H
L
X
X
Q0
L
Q0
H
Q0
H
Q0
L
H
H
H
H
H
H
X or
L
L
L
↑
↓
H
H
H
H
H
L
L or H
↑
L or H
↓
X
Q0
Q0
Q0
Q0
L
Q0
H
Q0
H
Q0
L
H
L
H
H
↑
↓
H
X
H
H
H
L or H
X or
L or H
X or
Q0
L
Q0
L
Q0
L
X or floating
X or floating
floating floating
floating floating
[1] Q0 is the previous state of the associated output.
[2] DCS2 and DCS3 operate identically to DCS0 and DCS1, except they do not have corresponding re-driven (QCS) outputs.
Table 5.
RESET
Parity and standby function table
Inputs
CK
Output
PTYERR[3][4]
DCS0[1]
DCS1[1]
CK
∑ of inputs = H
PARIN[2]
(D0 to D21)
H
H
H
H
H
H
H
H
H
H
L
L
L
H
H
H
H
L
↑
↓
even
odd
L
H
↑
↓
L
L
L
↑
↓
even
odd
H
L
L
↑
↓
H
H
H
H
H
H
H
X
↑
↓
even
odd
L
H
L
↑
↓
L
L
L
↑
↓
even
odd
H
L
L
↑
↑
↓
↓
H
H
H
X
X
X
X
PTYERR0
PTYERR0
H
L or H
L or H
X
X or floating X or floating X or floating X or floating
X or floating
X or floating
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
8 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
[1] DCS2 and DCS3 operate identically to DCS0 and DCS1 with regard to the parity function.
[2] PARIN arrives one clock cycle after the data to which it applies. All Dn inputs must be driven to a known state for parity to be calculated
correctly.
[3] This condition assumes PTYERR is HIGH at the crossing of CK going HIGH and CK going LOW. If PTYERR is LOW, it stays latched
LOW for two clock cycles or until RESET is driven LOW. CSGATEEN is ‘don’t care’ for PTYERR.
[4] PTYERR0 is the previous state of output PTYERR.
7.2 Functional information
This 28-bit 1 : 2 registered buffer with parity is designed for 1.7 V to 2.0 V VDD operation.
All clock and data inputs are compatible with the JEDEC standard for SSTL_18. The
control inputs are LVCMOS. All outputs are 1.8 V CMOS drivers that have been optimized
to drive the DDR2 DIMM load.
The SSTUM32865 operates from a differential clock (CK and CK). Data are registered at
the crossing of CK going HIGH, and CK going LOW.
The device supports low-power standby operation. When the reset input (RESET) is LOW,
the differential input receivers are disabled, and undriven (floating) data, clock and
reference voltage (VREF) inputs are allowed. In addition, when RESET is LOW all
registers are reset, and all outputs except PTYERR are forced LOW. The LVCMOS
RESET input must always be held at a valid logic HIGH or LOW level.
To ensure defined outputs from the register before a stable clock has been supplied,
RESET must be held in the LOW state during power-up.
In the DDR2 RDIMM application, RESET is specified to be completely asynchronous with
respect to CK and CK. Therefore, no timing relationship can be guaranteed between the
two. When entering reset, the register will be cleared and the data outputs will be driven
LOW quickly, relative to the time to disable the differential input receivers. However, when
coming out of reset, the register will become active quickly, relative to the time to enable
the differential input receivers. As long as the data inputs are LOW, and the clock is stable
during the time from the LOW-to-HIGH transition of RESET until the input receivers are
fully enabled, the design of the SSTUM32865 ensures that the outputs remain LOW, thus
ensuring no glitches on the output.
The device monitors DCS0, DCS1, DCS2 and DCS3 inputs and will gate the Qn outputs
from changing states when all DCSn inputs are HIGH. If DCSn input is LOW, the Qn
outputs will function normally. The RESET input has priority over the DCSn control and
will force the Qn outputs LOW and the PTYERR output HIGH. If the DCSn-control
functionality is not desired, then the CSGATEEN input can be hardwired to ground, in
which case, the set-up time requirement for DCSn would be the same as for the other Dn
data inputs.
The SSTUM32865 includes a parity checking function. The SSTUM32865 accepts a
parity bit from the memory controller at its input pin PARIN, compares it with the data
received on the Dn inputs (with either DCSn inputs active) and indicates whether a parity
error has occurred on its open-drain PTYERR pin (active LOW).
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
9 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
7.3 Functional differences to SSTU32864
The SSTUM32865 for its basic register functionality, signal definition and performance is
based upon the industry-standard SSTU32864, but provides key operational features
which differ (at least in part) from the industry-standard register in the following aspects:
7.3.1 Chip Select (CS) gating of key inputs (DCS0, DCS1, DCS2, DCS3,
CSGATEEN)
As a means to reduce device power, the internal latches will only be updated when one or
more of the CS inputs are active (LOW) and CSGATEEN HIGH at the rising edge of the
clock. The 22 ‘Chip-Select-gated’ input signals associated with this function include
addresses (ADDR0 to ADDR15, BA0 to BA2), and RAS, CAS, WE, with the remaining
signals (CS, CKE, ODT) continuously re-driven at the rising edge of every clock as they
are independent of CS. The CS gating function can be disabled by tying CSGATEEN
LOW, enabling all internal latches to be updated on every rising edge of the clock.
Table 6.
Mode
Chip Select gating mode
Signal name
CSGATEEN
HIGH
Description
Gating
Registers only re-drive signals to the DRAMs when
Chip Select inputs are LOW.
Non-gating
CSGATEEN
LOW
Registers always re-drive signals on every clock cycle,
independent of the state of the Chip Select inputs.
7.3.2 Parity error checking and reporting
The SSTUM32865 incorporates a parity function, whereby the signal received on input pin
PARIN is received as parity to the register, one clock cycle later than the CS-gated inputs.
The received parity bit is then compared to the parity calculated across these same inputs
by the register parity logic to verify that the information has not been corrupted. The 22
CS-gated input signals will be latched and re-driven on the first clock, and any error will be
reported one clock cycle later via the PTYERR output pin (driven LOW for two consecutive
clock cycles). PTYERR is an open-drain output, allowing multiple modules to share a
common signal pin for reporting the occurrence of a parity error during a valid command
cycle (coincident with the re-driven signals). This output is driven LOW for two consecutive
clock cycles to allow the memory controller sufficient time to sense and capture the error
even. A LOW state on PTYERR indicates that a parity error has occurred.
7.3.3 Reset (RESET)
Similar to the RESET pin on the industry-standard SSTU32864, this pin is used to clear all
internal latches and all outputs will be driven LOW quickly except the PTYERR output,
which will be floated (and will normally default HIGH by their external pull-up).
7.3.4 Power-up sequence
The reset function for the SSTUM32865 is similar to that of the SSTU32864 except that
the PTYERR signal is also cleared and will be held clear (HIGH) for three consecutive
clock cycles.
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
10 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
RESET
DCSn
CK
m
m + 1
m + 2
m + 3
m + 4
CK
t
ACT
t
t
h
su
(1)
Dn
t
, t
PDM PDMSS
CK to Q
Qn
t
t
h
su
PARIN
t
t
, t
PHL PLH
PHL
CK to PTYERR
CK to PTYERR
PTYERR
002aaa983
HIGH, LOW, or Don't care
HIGH or LOW
(1) After RESET is switched from LOW to HIGH, all data and PARIN input signals must be set and held LOW for a minimum
time of tACT(max) to avoid false error.
Fig 4. RESET switches from LOW to HIGH
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
11 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
RESET
DCSn
CK
m
m + 1
m + 2
m + 3
m + 4
CK
t
t
h
su
(1)
Dn
t
, t
PDM PDMSS
CK to Q
Qn
t
su
t
h
PARIN
t
, t
PHL PLH
CK to PTYERR
PTYERR
002aaa984
Output signal is dependent
on the prior unknown event
Unknown input event
HIGH or LOW
Fig 5. RESET being held HIGH
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
12 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
RESET
DCSn
t
INACT
(1)
CK
(1)
CK
(1)
Dn
t
PHL
RESET to Q
Qn
(1)
PARIN
t
PLH
RESET to PTYERR
PTYERR
002aac649
HIGH, LOW, or Don't care
HIGH or LOW
(1) After RESET is switched from HIGH to LOW, all data and clock input signals must be set and held at valid logic levels (not
floating) for a minimum time of tINACT(max)
.
Fig 6. RESET switches from HIGH to LOW
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
13 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
22
22
Dn
QnA
QnB
D
Q
D
D
PTYERR
D
LATCHING AND
RESET FUNCTION
(1)
PARIN
CLOCK
002aaa417
(1) This function holds the error for two cycles. For details, see Section 7 “Functional description” and Figure 4 “RESET
switches from LOW to HIGH”.
Fig 7. Parity logic diagram
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
14 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
8. Limiting values
Table 7.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
VDD
VI
Parameter
Conditions
Min
Max
Unit
V
supply voltage
−0.5
+2.5
[1]
[1]
input voltage
receiver
−0.5
+2.5
V
VO
output voltage
driver
−0.5
VDD + 0.5
−50
V
IIK
input clamping current
output clamping current
output current
VI < 0 V or VI > VDD
VO < 0 V or VO > VDD
continuous; 0 V < VO < VDD
-
-
-
-
mA
mA
mA
mA
IOK
±50
IO
±50
IDDC
continuous current through
each VDD[2] or GND pin
±100
Tstg
storage temperature
−65
2
+150
°C
kV
V
Vesd
electrostatic discharge
voltage
Human Body Model (HBM); 1.5 kΩ; 100 pF
Machine Model (MM); 0 Ω; 200 pF
-
-
150
[1] The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
[2] Pins VDDL or VDDR.
9. Recommended operating conditions
Table 8.
Recommended operating conditions
Symbol Parameter
Conditions
Min
Typ
Max
Unit
VDD
supply voltage
1.7
-
2.0
V
V
V
V
V
V
V
V
V
V
V
Vref
reference voltage
0.49 × VDD
0.50 × VDD 0.51 × VDD
VT
termination voltage
V
ref − 0.040 Vref
Vref + 0.040
VI
input voltage
0
-
-
-
-
-
-
-
-
VDD
-
[1]
[1]
[1]
[1]
[2]
[2]
VIH(AC)
VIL(AC)
VIH(DC)
VIL(DC)
VIH
AC HIGH-level input voltage
AC LOW-level input voltage
DC HIGH-level input voltage
DC LOW-level input voltage
HIGH-level input voltage
LOW-level input voltage
data inputs (Dn)
data inputs (Dn)
data inputs (Dn)
data inputs (Dn)
RESET
Vref + 0.250
-
Vref − 0.250
Vref + 0.125
-
-
Vref − 0.125
-
0.65 × VDD
VIL
RESET
-
0.35 × VDD
VICR
common mode input voltage
range
CK, CK
0.675
1.125
VID
IOH
IOL
differential input voltage
HIGH-level output current
LOW-level output current
ambient temperature
CK, CK
600
-
-
-
-
mV
mA
mA
-
-
−8
8
Tamb
operating in free air
SSTUM32865ET/G
SSTUM32865ET/S
0
0
-
-
+70
+85
°C
°C
[1] The differential inputs must not be floating, unless RESET is LOW.
[2] The RESET input of the device must be held at valid logic levels (not floating) to ensure proper device operation.
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
15 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
10. Characteristics
Table 9.
Characteristics
Over recommended operating conditions, unless otherwise noted.
Symbol
VOH
VOL
Parameter
Conditions
Min
Typ
Max
-
Unit
V
HIGH-level output voltage
LOW-level output voltage
input current
IOH = −6 mA; VDD = 1.7 V
IOL = 6 mA; VDD = 1.7 V
all inputs; VI = VDD or GND;
1.2
-
-
-
-
-
0.5
±5
V
II
µA
VDD = 2.0 V
IDD
supply current
static standby current;
RESET = GND; VDD = 2.0 V
-
-
-
-
2
mA
mA
static operating current;
RESET = VDD; VDD = 2.0 V;
VI = VIH(AC) or VIL(AC)
40
IDDD
dynamic operating current per MHz
clock only; RESET = VDD
;
-
-
16
19
-
-
µA
µA
VI = VIH(AC) or VIL(AC); CK and CK
switching at 50 % duty cycle.
IO = 0 mA; VDD = 1.8 V
per each data input;
RESET = VDD
;
VI = VIH(AC) or VIL(AC); CK and CK
switching at 50 % duty cycle. One
data input switching at half clock
frequency, 50 % duty cycle.
IO = 0 mA; VDD = 1.8 V
Ci
input capacitance
output impedance
data inputs; VI = Vref ± 250 mV;
2.5
2
-
-
-
3.5
3
pF
pF
pF
V
DD = 1.8 V
CK and CK; VICR = 0.9 V;
ID = 600 mV; VDD = 1.8 V
RESET; VI = VDD or GND;
DD = 1.8 V
V
3
5
V
[1]
Zo
instantaneous
steady-state
-
-
7
-
-
Ω
Ω
53
[1] Instantaneous is defined as within < 2 ns following the output data transition edge.
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
16 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
Table 10. Timing requirements
Over recommended operating conditions, unless otherwise noted.
Symbol
fclock
tW
Parameter
Conditions
Min
Typ
Max
450
-
Unit
MHz
ns
clock frequency
-
-
-
-
-
-
pulse width
CK, CK HIGH or LOW
1
[1][2]
[1][3]
tACT
differential inputs active time
differential inputs inactive time
set-up time
-
10
15
-
ns
tINACT
tsu
-
ns
Chip Select; DCS0, DCS1
valid before clock
switching
0.6
ns
Data; Dn valid before
clock switching
0.5
0.5
0.4
0.4
-
-
-
-
-
-
-
-
ns
ns
ns
ns
PARIN; PARIN before CK
and CK
th
hold time
input to remain valid after
clock switching
PARIN after CK and CK
[1] This parameter is not necessarily production tested.
[2] Data inputs must be active below a minimum time of tACT(max) after RESET is taken HIGH.
[3] Data and clock inputs must be held at valid levels (not floating) a minimum time of tINACT(max) after RESET is taken LOW.
Table 11. Switching characteristics
Over recommended operating conditions, unless otherwise noted.
Symbol
fmax
Parameter
Conditions
Min
450
1.0
1.2
1
Typ
Max
-
Unit
MHz
ns
maximum input clock frequency
peak propagation delay
LOW to HIGH delay time
HIGH to LOW delay time
LOW-to-HIGH propagation delay
-
-
-
-
-
-
[1]
tPDM
tLH
CK and CK to output
CK and CK to PTYERR
CK and CK to PTYERR
from RESET to PTYERR
CK and CK to output
1.4
3
ns
tHL
3
ns
tPLH
-
3
ns
[1][2]
tPDMSS
simultaneous switching peak
propagation delay
-
1.5
ns
tPHL
HIGH-to-LOW propagation delay
RESET to output
-
-
3
ns
[1] Includes 350 ps of test-load transmission line delay.
[2] This parameter is not necessarily production tested.
Table 12. Output edge rates
Over recommended operating conditions, unless otherwise noted.
Symbol
dV/dt_r
dV/dt_f
dV/dt_∆
Parameter
Conditions
Min
Typ
Max
Unit
V/ns
V/ns
V/ns
rising edge slew rate
falling edge slew rate
1
1
-
-
-
-
4
4
1
absolute difference between dV/dt_r
and dV/dt_f
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
17 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
11. Test information
11.1 Test circuit
All input pulses are supplied by generators having the following characteristics:
Pulse Repetition Rate (PRR) ≤ 10 MHz; Z0 = 50 Ω; input slew rate = 1 V/ns ± 20 %,
unless otherwise specified.
The outputs are measured one at a time with one transition per measurement.
V
DD
DUT
delay = 350 ps
= 50 Ω
R
= 1000 Ω
= 1000 Ω
L
50 Ω
Z
o
CK
CK
CK inputs
OUT
(1)
= 30 pF
C
L
R
L
test point
R
L
= 100 Ω
test point
002aaa371
(1) CL includes probe and jig capacitance.
Fig 8. Load circuit
LVCMOS
V
DD
0.5V
0.5V
RESET
DD
DD
0 V
t
t
ACT
INACT
90 %
(1)
DD
I
10 %
002aaa372
(1) IDD tested with clock and data inputs held at VDD or GND, and IO = 0 mA.
Fig 9. Voltage and current waveforms; inputs active and inactive times
t
W
V
V
IH
IL
V
input
V
V
ICR
ID
ICR
002aaa373
VID = 600 mV.
VIH = Vref + 250 mV (AC voltage levels) for differential inputs. VIH = VDD for LVCMOS inputs.
VIL = Vref − 250 mV (AC voltage levels) for differential inputs. VIL = GND for LVCMOS inputs.
Fig 10. Voltage waveforms; pulse duration
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
18 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
CK
CK
V
V
ICR
ID
t
t
h
su
V
V
IH
IL
input
V
ref
V
ref
002aaa374
VID = 600 mV.
Vref = 0.5VDD
.
VIH = Vref + 250 mV (AC voltage levels) for differential inputs. VIH = VDD for LVCMOS inputs.
VIL = Vref − 250 mV (AC voltage levels) for differential inputs. VIL = GND for LVCMOS inputs.
Fig 11. Voltage waveforms; set-up and hold times
CK
V
V
V
i(p-p)
ICR
ICR
CK
t
t
PHL
PLH
V
V
OH
OL
V
output
T
002aaa375
tPLH and tPHL are the same as tPD
.
Fig 12. Voltage waveforms; propagation delay times (clock to output)
LVCMOS
V
V
V
V
IH
RESET
0.5V
DD
IL
t
PHL
OH
OL
output
V
T
002aaa376
tPLH and tPHL are the same as tPD
.
VIH = Vref + 250 mV (AC voltage levels) for differential inputs. VIH = VDD for LVCMOS inputs.
VIL = Vref − 250 mV (AC voltage levels) for differential inputs. VIL = GND for LVCMOS inputs.
Fig 13. Voltage waveforms; propagation delay times (reset to output)
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
19 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
11.2 Output slew rate measurement
VDD = 1.8 V ± 0.1 V.
All input pulses are supplied by generators having the following characteristics:
PRR ≤ 10 MHz; Zo = 50 Ω; input slew rate = 1 V/ns ± 20 %, unless otherwise specified.
V
DD
R
DUT
= 50 Ω
L
OUT
test point
002aaa377
(1)
= 10 pF
C
L
(1) CL includes probe and jig capacitance.
Fig 14. Load circuit, HIGH-to-LOW slew measurement
output
V
OH
80 %
dv_f
20 %
V
OL
dt_f
002aaa378
Fig 15. Voltage waveforms, HIGH-to-LOW slew rate measurement
DUT
OUT
test point
(1)
= 10 pF
C
L
R
L
= 50 Ω
002aaa379
(1) CL includes probe and jig capacitance.
Fig 16. Load circuit, LOW-to-HIGH slew measurement
dt_r
V
V
OH
80 %
dv_r
20 %
output
OL
002aaa380
Fig 17. Voltage waveforms, LOW-to-HIGH slew rate measurement
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
20 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
11.3 Error output load circuit and voltage measurement
VDD = 1.8 V ± 0.1 V.
All input pulses are supplied by generators having the following characteristics:
PRR ≤ 10 MHz; Zo = 50 Ω; input slew rate = 1 V/ns ± 20 %, unless otherwise specified.
V
DD
R
DUT
= 1 kΩ
L
OUT
test point
002aaa500
(1)
= 10 pF
C
L
(1) CL includes probe and jig capacitance.
Fig 18. Load circuit, error output measurements
LVCMOS
V
DD
RESET
0.5V
DD
0 V
t
PLH
V
OH
output
waveform 2
0.15 V
0 V
002aaa501
Fig 19. Voltage waveforms, open-drain output LOW-to-HIGH transition time with respect to
RESET input
timing
inputs
V
i(p-p)
V
V
ICR
ICR
t
HL
V
V
DD
OL
output
waveform 1
0.5V
DD
002aaa502
Fig 20. Voltage waveforms, open-drain output HIGH-to-LOW transition time with respect
to clock inputs
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
21 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
timing
inputs
V
V
i(p-p)
V
ICR
ICR
t
LH
V
OH
output
waveform 2
0.15 V
0 V
002aaa503
Fig 21. Voltage waveforms, open-drain output LOW-to-HIGH transition time with respect to
clock inputs
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
22 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
12. Package outline
TFBGA160: plastic thin fine-pitch ball grid array package; 160 balls; body 9 x 13 x 0.7 mm
SOT802-2
D
B
A
ball A1
index area
A
2
E
A
A
1
detail X
e
1
C
1/2 e
y
C
1
y
M
v
C
C
A
B
e
b
M
w
V
U
T
R
P
N
M
L
e
K
J
e
2
H
G
F
1/2 e
E
D
C
B
A
ball A1
index area
1
3
5
7
9
11
2
4
6
8
10 12
X
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
A
1
A
2
b
D
E
e
e
1
e
v
w
y
y
1
2
max
0.35 0.80 0.45
0.25 0.65 0.35
9.1
8.9
13.1
12.9
mm
1.15
0.65 7.15 11.05 0.15 0.08
0.1
0.1
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
- - -
JEITA
05-06-21
05-07-13
- - -
- - -
SOT802-2
Fig 22. Package outline SOT802-2 (TFBGA160)
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
23 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
13. Soldering
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
13.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
13.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
• Board specifications, including the board finish, solder masks and vias
• Package footprints, including solder thieves and orientation
• The moisture sensitivity level of the packages
• Package placement
• Inspection and repair
• Lead-free soldering versus PbSn soldering
13.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
24 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
13.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 23) than a PbSn process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 13 and 14
Table 13. SnPb eutectic process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
235
≥ 350
220
< 2.5
≥ 2.5
220
220
Table 14. Lead-free process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
260
350 to 2000
> 2000
260
< 1.6
260
250
245
1.6 to 2.5
> 2.5
260
245
250
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 23.
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
25 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 23. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
14. Abbreviations
Table 15. Abbreviations
Acronym
CMOS
DDR2
Description
Complementary Metal Oxide Semiconductor
Double Data Rate 2
DIMM
Dual In-line Memory Module
DRAM
LVCMOS
MT/s
Dynamic Random Access Memory
Low Voltage Complementary Metal Oxide Semiconductor
Mega Transfers per second
RDIMM
SSTL
Registered Dual In-line Memory Module
Stub Series Terminated Logic
SSTL_18
Stub Series Terminated Logic for 1.8 V
15. Revision history
Table 16. Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
SSTUM32865_1
20070919
Product data sheet
-
-
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
26 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
malfunction of a NXP Semiconductors product can reasonably be expected to
16.2 Definitions
result in personal injury, death or severe property or environmental damage.
NXP Semiconductors accepts no liability for inclusion and/or use of NXP
Semiconductors products in such equipment or applications and therefore
such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
16.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
17. Contact information
For additional information, please visit: http://www.nxp.com
For sales office addresses, send an email to: salesaddresses@nxp.com
SSTUM32865_1
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 19 September 2007
27 of 28
SSTUM32865
NXP Semiconductors
1.8 V DDR2-800 registered buffer with parity
18. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Ordering options. . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3
3
4
4.1
5
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6
7
Functional description . . . . . . . . . . . . . . . . . . . 8
Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Functional information . . . . . . . . . . . . . . . . . . . 9
Functional differences to SSTU32864 . . . . . . 10
Chip Select (CS) gating of key inputs (DCS0,
DCS1, DCS2, DCS3, CSGATEEN) . . . . . . . . 10
Parity error checking and reporting. . . . . . . . . 10
Reset (RESET). . . . . . . . . . . . . . . . . . . . . . . . 10
Power-up sequence . . . . . . . . . . . . . . . . . . . . 10
7.1
7.2
7.3
7.3.1
7.3.2
7.3.3
7.3.4
8
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 15
Recommended operating conditions. . . . . . . 15
Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . 16
9
10
11
Test information. . . . . . . . . . . . . . . . . . . . . . . . 18
Test circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Output slew rate measurement. . . . . . . . . . . . 20
Error output load circuit and voltage
11.1
11.2
11.3
measurement . . . . . . . . . . . . . . . . . . . . . . . . . 21
12
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 23
13
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Introduction to soldering . . . . . . . . . . . . . . . . . 24
Wave and reflow soldering . . . . . . . . . . . . . . . 24
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 24
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 25
13.1
13.2
13.3
13.4
14
15
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 26
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 26
16
Legal information. . . . . . . . . . . . . . . . . . . . . . . 27
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 27
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
16.1
16.2
16.3
16.4
17
18
Contact information. . . . . . . . . . . . . . . . . . . . . 27
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2007.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 19 September 2007
Document identifier: SSTUM32865_1
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00260/img/page/SSTUM32865ET_1572282_files/SSTUM32865ET_1572282_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00260/img/page/SSTUM32865ET_1572282_files/SSTUM32865ET_1572282_2.jpg)
SSTUM32865ET/G
IC SSTU SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA160, 9 X 13 MM, 0.70 MM PITCH, LEAD FREE, PLASTIC, SOT-802-2, TFBGA-160, FF/Latch
NXP
![](http://pdffile.icpdf.com/pdf2/p00243/img/page/SSTUM32865ET_1468771_files/SSTUM32865ET_1468771_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00243/img/page/SSTUM32865ET_1468771_files/SSTUM32865ET_1468771_2.jpg)
SSTUM32865ET/G,518
SSTUM32865 - 1.8 V 28-bit 1 : 2 registered buffer with parity for DDR2-800 RDIMM applications BGA 160-Pin
NXP
![](http://pdffile.icpdf.com/pdf1/p00121/img/page/SSTUM32865_669259_files/SSTUM32865_669259_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00121/img/page/SSTUM32865_669259_files/SSTUM32865_669259_2.jpg)
SSTUM32865ET/S
IC SSTU SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA160, 9 X 13 MM, 0.70 MM PITCH, LEAD FREE, PLASTIC, SOT-802-2, TFBGA-160, FF/Latch
NXP
![](http://pdffile.icpdf.com/pdf2/p00243/img/page/SSTUM32865ET_1468771_files/SSTUM32865ET_1468771_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00243/img/page/SSTUM32865ET_1468771_files/SSTUM32865ET_1468771_2.jpg)
SSTUM32865ET/S,518
SSTUM32865 - 1.8 V 28-bit 1 : 2 registered buffer with parity for DDR2-800 RDIMM applications BGA 160-Pin
NXP
![](http://pdffile.icpdf.com/pdf1/p00134/img/page/SSTUM_743415_files/SSTUM_743415_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00134/img/page/SSTUM_743415_files/SSTUM_743415_2.jpg)
SSTUM32866
1.8 V 25-bit 1 : 1 or 14-bit 1 : 2 configurable registered buffer with parity for DDR2-1G RDIMM applications
NXP
![](http://pdffile.icpdf.com/pdf1/p00134/img/page/SSTUM_743415_files/SSTUM_743415_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00134/img/page/SSTUM_743415_files/SSTUM_743415_2.jpg)
SSTUM32866EC/G
1.8 V 25-bit 1 : 1 or 14-bit 1 : 2 configurable registered buffer with parity for DDR2-1G RDIMM applications
NXP
![](http://pdffile.icpdf.com/pdf2/p00243/img/page/SSTUM32866EC_1468772_files/SSTUM32866EC_1468772_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00243/img/page/SSTUM32866EC_1468772_files/SSTUM32866EC_1468772_2.jpg)
SSTUM32866EC/G,518
SSTUM32866 - 1.8 V 25-bit 1 : 1 or 14-bit 1 : 2 configurable registered buffer with parity for DDR2-1G RDIMM applications BGA 96-Pin
NXP
![](http://pdffile.icpdf.com/pdf1/p00134/img/page/SSTUM_743415_files/SSTUM_743415_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00134/img/page/SSTUM_743415_files/SSTUM_743415_2.jpg)
SSTUM32866EC/S
1.8 V 25-bit 1 : 1 or 14-bit 1 : 2 configurable registered buffer with parity for DDR2-1G RDIMM applications
NXP
![](http://pdffile.icpdf.com/pdf1/p00135/img/page/SSTUM_745029_files/SSTUM_745029_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00135/img/page/SSTUM_745029_files/SSTUM_745029_2.jpg)
SSTUM32868
1.8 V 28-bit 1 : 2 configurable registered buffer with parity for DDR2-800 RDIMM applications
NXP
©2020 ICPDF网 联系我们和版权申明