TEA5764UK/N2,027 [NXP]
IC FM, AUDIO SINGLE CHIP RECEIVER, PBGA34, 4 X 4 MM, WLB-34, Receiver IC;型号: | TEA5764UK/N2,027 |
厂家: | NXP |
描述: | IC FM, AUDIO SINGLE CHIP RECEIVER, PBGA34, 4 X 4 MM, WLB-34, Receiver IC 商用集成电路 |
文件: | 总64页 (文件大小:270K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TEA5764UK
FM radio + RDS
Rev. 02 — 9 August 2005
Product data sheet
1. General description
The TEA5764UK is a single chip electronically tuned FM stereo radio with Radio Data
System (RDS) and Radio Broadcast Data System (RBDS) demodulator and RDS/RBDS
decoder for portable application with fully integrated IF selectivity and demodulation.
The radio is completely adjustment free and only requires a minimum of small and low
cost external components.
The radio can tune to the European, US and Japanese FM bands. It has a low power
consumption and can operate at a low supply voltage.
2. Features
■ Chip scale package
■ High sensitivity due to integrated low noise RF input amplifier
■ FM mixer for conversion of the US/Europe (87.5 MHz to 108 MHz) and Japanese FM
band (76 MHz to 90 MHz) to IF
■ Preset tuning to receive Japanese TV audio up to 108 MHz
■ Auto search tuning, raster 100 kHz
■ RF automatic gain control circuit
■ LC tuner oscillator operating with low cost fixed chip inductors
■ Fully integrated FM IF selectivity
■ Fully integrated FM demodulator; no external discriminator
■ Crystal oscillator at 32768 Hz, or external reference frequency at 32768 Hz
■ PLL synthesizer tuning system
■ IF counter; 7-bit output via the I2C-bus
■ Level detector; 4-bit level information output via the I2C-bus
■ Soft mute: signal dependent mute function
■ Mono/stereo blend: gradual change from mono to stereo, depending on signal
■ Adjustment-free stereo decoder
■ Autonomous search tuning function
■ Standby mode
■ MPX output
■ One software programmable port
■ Fully integrated RDS/RBDS demodulator in accordance with EN50067
■ RDS/RBDS decoder with memory for two RDS data blocks provides block
synchronization and error correction; block data and status information are available
via the I2C-bus
■ Audio pause detector
TEA5764UK
Philips Semiconductors
FM radio + RDS
■ Interrupt flag
3. Applications
■ FM stereo radio
4. Quick reference data
Table 1:
Electrical parameters general
The listed parameters are valid when a crystal is used that meets the requirements as stated in Table 46; All RF input values
are defined in potential difference, except when EMF is explicitly stated.
Symbol
Supplies
VCCA
Parameter
Conditions
Min
Typ
Max
Unit
analog supply voltage
analog supply current
2.5
2.7
3.3
V
ICCA
VCCA = 2.5 V to 3.3 V
operating mode
Standby mode
12
0
13.7
0.1
16
1
mA
µA
V
VCCD
ICCD
digital supply voltage
digital supply current
2.5
2.7
3.3
VCCD = 2.5 V to 3.3 V
operating mode
Standby mode
0.3
1
0.7
15
1.5
mA
22.5
µA
Reference voltage
VVREFDIG
digital reference voltage
1.65
0
1.8
0.5
VCCD
1
V
for I2C-bus interface
IVREFDIG
digital reference supply
current
operating mode;
µA
VVREFDIG = 1.65 V to VCCD
General
fi(FM)
FM input frequency
ambient temperature
76
-
-
108
+85
MHz
Tamb
−40
°C
FM and RDS overall system parameters
Vsens(EMF)
sensitivity EMF value
voltage
fRF = 76 MHz to 108 MHz;
∆f = 22.5 kHz; fmod = 1 kHz;
(S+N)/N = 26 dB; TCdeem = 75 µs;
A-weighting filter;
-
2.9
4.4
µV
B
aud = 300 Hz to 15 kHz
∆f1 = 200 kHz; ∆f2 = 400 kHz;
tune = 76 MHz to 108 MHz;
IP3in
IP3out
S
in-band 3rd-order
intercept point
78
87
87
93
-
-
dBµV
dBµV
f
RFagc = off
out-of-band 3rd-order
intercept point
∆f1 = 4 MHz; ∆f2 = 8 MHz;
ftune = 76 MHz to 108 MHz;
RFagc = off
[1]
selectivity
ftune = 76 MHz to 108 MHz
high-side; ∆f = +200 kHz
low-side; ∆f = −200 kHz
VRF = 1 mV; L = R; ∆f = 22.5 kHz;
39
32
55
43
36
66
-
dB
dB
mV
-
VVAFL
left audio output voltage
on pin VAFL
75
fmod = 1 kHz; no pre-emphasis;
TCdeem = 75 µs
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
2 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 1:
Electrical parameters general
The listed parameters are valid when a crystal is used that meets the requirements as stated in Table 46; All RF input values
are defined in potential difference, except when EMF is explicitly stated.
Symbol
Parameter
right audio output voltage VRF = 1 mV; L = R; ∆f = 22.5 kHz;
on pin VAFR mod = 1 kHz; no pre-emphasis;
TCdeem = 75 µs
(S+N)/N(m) maximum signal-to-noise VRF = 1 mV; ∆f = 22.5 kHz; L = R;
Conditions
Min
Typ
Max
Unit
VVAFR
55
66
75
mV
f
54
50
57
54
-
-
dB
dB
ratio, mono
f
B
mod = 1 kHz; de-emphasis = 75 µs;
AF = 300 Hz to 15 kHz; A-weighting
filter
(S+N)/N(s) maximum signal-to-noise
ratio, stereo
VRF = 1 mV; ∆f = 67.5 kHz; L = R;
fmod = 1 kHz; ∆fpilot = 6.75 kHz;
de-emphasis = 75 µs; BAF = 300 Hz
to 15 kHz; A-weighting filter
αcs
channel separation
MST = 0; R = 1 and L = 0 or R = 0
and L = 1; VRF = 30 µV; increasing
RF input level
27
-
33
-
dB
%
THD
total harmonic distortion
VRF = 1 mV; ∆f = 75 kHz;
0.4
0.9
fmod = 1 kHz; DTC = 0; Baud = 300 Hz
to 15 kHz; A-weighting filter; mono;
L = R; no pilot deviation
Vsens
RDS sensitivity EMF
value
∆f = 22.5 kHz; fAF = 1 kHz; L = R;
SYM1 = 0 and SYM0 = 0; average
over 2000 blocks; block quality
rate ≥ 95 %; ∆fRDS = 2 kHz
-
17
30
µV
[1] Low-side and high-side selectivity can be measured by changing the mixer LO injection from high-side to low-side.
5. Ordering information
Table 2:
Ordering information
Type number
Package
Name
Description
Version
TEA5764UK
WLB34
wafer-level ball grid array; 34 balls; 4 × 4 × 0.36 mm
TEA5764UK
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
3 of 64
xxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx x xxxxxxxxxxxxxx xxxxxxxxxx xxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx
xxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxx x x
33 nF
33 nF
VAFR TMUTE
G5 G6
GNDA
F2
GNDD
G2
MPXIN
MPXOUT VAFL
G4 F4
INTCON1
F6
G3
G1
F1
FREQIN
XTAL
CRYSTAL
OSCILLATOR
12 pF
X1
TEA5764UK
GAIN
STABILIZER
V
CCA E1
57 kHz BP
FILTER
3.7
Ω
CD3
IF
FILTER
SOFT
MUTE
LIMITER
DEMODULATOR
IF COUNT
D2
G7
RDS/RBDS
DECODER
INTX
33 nF
SDS
FM
antenna
LEVEL
ADC
10 nF
INTERFACE
REGISTER
MPX
DECODER
I/Q MIXER
1st FM
÷2
N1
100 pF
I
F7
E6
ref
PAUSE
DETECTOR
IF CENTER
FREQUENCY ADJUST
GNDD
27
pF
D1
C1
RFIN1
RFIN2
L1
120 nH
INTCON2
AGC
47
pF
E7
CD2/INTCON3
C2
B1
GNDRF
CAGC
mono
pilot
12 Ω
V
D7
CCD
prog. div out
ref. div out
D6
C7
GNDD
GNDD
2
I C-BUS
TUNING SYSTEM
INTERFACE
B7
SDA
MUX
VCO
A2
LO1
SW PORT
A5
A4
A3
LO2 CD1
B4
A4
B6
A7
A1
B2
001aab458
CPOUT
LOOPSW
PILLP
SWPORT
SCL
BUSENABLE
VREFDIG
10
nF
33 nF
47 kΩ
10 kΩ
D1
D2
33 nF
33 nF
100 kΩ
L3
L3
33 nF
Fig 1. Block diagram
TEA5764UK
Philips Semiconductors
FM radio + RDS
7. Pinning information
7.1 Pinning
ball A1
index area
TEA5764UK
1
2
3
4
5
6
7
A
B
C
D
E
F
G
001aac987
Transparent top view
Fig 2. Ball configuration TEA5764UK
7.2 Pin description
Table 3:
Pin description
Symbol
LOOPSW
CPOUT
LO1
Ball
A1
B2
A2
A3
A4
B4
A5
A6
B6
A7
B7
-
Description
synthesizer PLL loop filter switch output
charge pump output of synthesizer PLL
local oscillator coil connection 1
local oscillator coil connection 2
VCO supply decoupling capacitor
pilot PLL loop filter
LO2
CD1
PILLP
SWPORT
BUSENABLE
VREFDIG
SCL
software programmable port output
I2C-bus enable input
digital reference voltage for I2C-bus signals
I2C-bus clock line input
I2C-bus data line input and output
not connected
SDA
n.c.
GNDD
GNDD
VCCD
C7
D6
D7
digital ground
digital ground
digital supply voltage
internally connected
not connected
CD2/INTCON3 E7
n.c.
-
INTCON2
GNDD
INTX
E6
F7
G7
-
internally connected; leave open
digital ground
interrupt flag output
n.c.
not connected
INTCON1
F6
internally connected; leave open
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
5 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 3:
Symbol
TMUTE
VAFR
Pin description …continued
Ball
G6
G5
F4
Description
soft mute time-constant capacitor
right audio output
VAFL
left audio output
MPXOUT
MPXIN
GNDD
G4
G3
G2
FM demodulator MPX output
MPX decoder and RDS decoder MPX input
digital ground; this pin has an internal pull-down resistor of 10 kΩ
to ground
n.c.
-
not connected
GNDA
n.c.
F2
-
analog ground
not connected
FREQIN
XTAL
VCCA
G1
F1
E1
D2
D1
C1
C2
B1
-
32.768 kHz reference frequency input
crystal oscillator input
analog supply voltage
VCCA decoupling capacitor
RF input 1
CD3
RFIN1
RFIN2
GNDRF
CAGC
n.c.
RF input 2
RF ground
RF AGC time-constant capacitor
not connected
8. Functional description
8.1 Low noise RF amplifier
The LNA input impedance together with the LC RF input circuit defines an FM band filter.
The gain of the LNA is controlled by the RF AGC circuit.
8.2 FM I/Q mixer
FM quadrature mixer converts FM RF (76 MHz to 108 MHz) to IF.
8.3 VCO
The varactor tuned LC VCO provides the Local Oscillator (LO) signal for the FM
quadrature mixer. The VCO frequency range is 150 MHz to 217 MHz.
8.4 Crystal oscillator
The crystal oscillator can operate with a 32.768 kHz clock crystal. The oscillator can be
overridden via the FREFIN pin. When the FREFIN pin is used the oscillator is clocked
externally by a 32.768 kHz signal. Selection between a reference clock or a reference
crystal can be done via the I2C-bus. When a crystal is connected the FREFIN pin must be
left open-circuit, and when pin FREFIN is used a crystal may not be connected. It is not
possible to connect a crystal and apply a frequency via the FREFIN pin in the same
application.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
6 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
The crystal oscillator generates the reference frequency for the following:
• Reference frequency divider for synthesizer PLL
• Timing for the IF counter
• Timing for the pause detector
• Free running frequency adjustment of the stereo decoder VCO
• Centre frequency for adjustment of the IF filters
• Clock frequency of the RDS/RBDS decoder
8.5 PLL tuning system
The PLL synthesizer tuning system is suitable to operate with a 32.768 kHz reference
frequency generated by the crystal oscillator or a reference clock of 32.768 kHz fed into
the TEA5764UK. To tune the radio to the required frequency requires the PLL word to be
calculated and then programmed to the register. The PLL word is 14 bits long; see
Table 20 and Table 21. Calculation of this 14-bit word can be done as follows.
Formula for high-side injection:
4 × ( f RF + f IF
)
NDEC
=
(1)
(2)
--------------------------------------
f ref
Formula for low-side injection:
4 × ( f RF – f IF
)
NDEC
=
-------------------------------------
f ref
where:
NDEC = decimal value of PLL word
fRF = wanted tuning frequency (Hz)
fIF = intermediate frequency of 225 kHz
fREFS = the reference frequency of 32.768 kHz
Example for receiving a channel at 100.1 MHz:
4 × (100.1 × 106 + 225 × 103)
NDEC
=
= 12246.704
(3)
------------------------------------------------------------------------
32768
The result found using Equation 1 or Equation 2 must always be rounded to the lowest
integer value. If rounded down to the lowest integer value of NDEC = 12246, the PLL word
becomes 2FD6h.
This value can be written to register FRQSETLSB or FRQSETMSB via the I2C-bus and
the IC will then either start an autonomous search at this frequency or go to a preset
channel at this frequency. When the application is built according to the block diagram
shown in Figure 1, and with the preferred components, the PLL will settle to the new
frequency within 5 ms. The most accurate tuning is accomplished when a search is
followed by a preset to the same frequency.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
7 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
The PLL is triggered by writing to any one of the bytes FRQSETMSB, FRQSETLSB,
TNCTRL1, TNCTRL2, TESTBITS, TESTMODE.
Accurate validation of the PLL locking on the new frequency can take 2 ms to 10 ms.
When a lock is detected, bit LD is set.
8.6 Band limits
The TEA5764UK can be switched either to the Japanese FM band or to the US/Europe
FM band. Setting bit BLIM to logic 0 the band range is 87.5 MHz to 108 MHz; setting bit
BLIM to logic 1 selects the Japanese band range of 76 MHz to 90 MHz.
8.7 RF AGC
The RF AGC (or wideband AGC) prevents overloading and limits the amount of
intermodulation products created by strong adjacent channels. The RF AGC is on by
default and can be turned off via the I2C-bus.
The TEA5764UK also has an in-band AGC to prevent overloading by the wanted channel.
The in-band AGC is always turned on.
8.8 Local or long distance receive
If bit LDX = 1, the LNA gain is reduced by 6 dB to prevent distortion when a transmitter is
very near. If bit LDX = 0, the LNA gain is normal to receive long distance (DX) stations.
8.9 IF filter
A fully integrated IF filter is built-in.
8.10 FM demodulator
The FM quadrature demodulator has an integrated resonator to perform the phase shift of
the IF signal.
8.11 IF counter
The received signal is mixed to produce an IF of 225 kHz. The result of the mixing is
counted. A good IF count result indicates that the radio is tuned to a valid channel instead
of an image or a channel with much interference. The IF counter outputs a 7-bit count
result via the I2C-bus. The IF counter is continuously active and can be read at any time
via the I2C-bus. It also activates a flag when the IF count result is outside the IF count
valid result window; see Section 9.1.4.4.
Before a tuning cycle is initiated the IF count period can be set to 2 ms or to 15.6 ms by
bit IFCTC. When the IF count period is set to 2 ms, initiating the tuning algorithm with a
preset (bit SM = 0) will always give an RDS update as shown in Section 8.22.1. In case
the IF count time is set to 15.6 ms, the tuning flowchart illustrated in Figure 3 is used.
Once tuned, the IF count period is always 15.6 ms.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
8 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
8.12 Voltage level generator and analog-to-digital converter
The voltage level indicates the field strength received by the antenna. The voltage level is
analog-to-digital converted to a 4-bit word and output via the I2C-bus. The ADC level is
continuously active and can be read at any time via the I2C-bus. It also activates a flag
when the voltage level falls below a predefined selectable threshold. Bit LHSW allows
either large or small hysteresis steps to be chosen; see Table 24 and Section 9.1.4.5.
When the ADC level is set to 3, its minimum value, the search algorithm will only stop at
channels having a RF level higher than, or equal to, ADC level 3. After completing the
search algorithm and being tuned to a station, due to hysteresis the effective limit will be
set to 0. This means that the continuous ADC level check will never set the LEVFLAG.
8.13 Mute
8.13.1 Soft mute
The low-pass filtered voltage level drives the soft mute attenuator at low RF input levels:
the audio output is faded and hence also the noise (see graphs referenced 1 in Figure 15
and Figure 17).
The soft mute function can also be switched off via the I2C-bus, using bit SMUTE.
8.13.2 Hard mute
The audio outputs VAFL and VAFR can be hard-muted by bit MU in byte TNCTRL2, which
means that they are put into 3-state. This can also be done by setting bits Left Hard Mute
(LHM) or Right Hard Mute (RHM) in byte TESTBITS, which allows either one or both
channels to be muted and forces the TEA5764UK to mono mode. When the TEA5764UK
is in Standby mode the audio outputs are hard-muted.
8.13.3 Audio frequency mute
The audio signal is muted by setting bit AFM of the TNCTRL1 register to logic 1. In the
soft mute attenuator the audio signal is blocked and so pins VAFL and VAFR will be at
their DC biasing point with no signal.
The audio is automatically muted during an RDS update as shown in the flowchart of
Figure 3. When the audio must be muted during Search mode, it is done by setting bit
AFM to logic 1 before the search action and resetting it to logic 0 afterwards.
Setting bit AFM to logic 0 stops the RDS data.
8.14 MPX decoder
The PLL stereo decoder is adjustment free. It can be switched to mono via the I2C-bus.
8.15 Signal dependent mono/stereo blend (stereo noise cancellation)
If the RF input level decreases, the MPX decoder blends from stereo to mono to limit the
output noise. The continuous mono-to-stereo blend can also be programmed via the
I2C-bus to an RF level dependent switched mono-to-stereo transition. Stereo noise
cancellation can be switched off via the I2C-bus by bit SNC.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
9 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
8.16 Software programmable port
One software programmable port (CMOS output) can be addressed via the I2C-bus:
Bit SWPM = 1, the software port functions as the output for the FRRFLAG.
Bit SWPM = 0, the software port outputs bit SWP of the registers.
In Test mode the software port outputs signals according to Table 27. Test mode is
selected, setting bit TM of byte TESTMODE to logic 1.
The software port cannot be disabled by the PUPD bits; see Section 8.17.
8.17 Standby mode
The radio can be put into Standby mode by the Power-Up / Power-Down (PUPD) bits. The
RDS part can be turned off separately or both the RDS and the FM part can be turned off.
The TEA5764UK is still accessible via the I2C-bus but takes only a low power from the
supply, in Standby mode, the audio outputs are hard-muted.
8.18 Power-on reset
After startup of VCCA and VCCD a power-on reset circuit will generate a reset pulse and the
registers will be set to their default values. The power-on reset is effectively generated by
VCCD
.
After a power-on reset the TEA5764UK is in Standby mode and the PUPD bits are set to
logic 0. After a power-on reset the registers are reset to their default value, except for
byte12R to byte19R and flags DAVFLG, LSYNCFLG and PDFLAG. To reset these, the
RDS part must be turned on by setting PUPD. After setting PUPD to logic 1, it will take
0.9 ms to start-up the TEA5764UK and set these registers to their default value.
The power supplies can be switched on in any order.
When the supply voltage VCCA and VCCD are at 0 V, all I/Os, the audio outputs and the
reference clock input are high-ohmic.
8.19 RDS/RBDS
8.19.1 RDS/RBDS demodulator
A fully integrated RDS/RBDS demodulator which uses the reference frequency
(32.678 Hz) of the PLL synthesizer tuning system. The RDS demodulator recovers and
regenerates the continuously transmitted RDS or RBDS data stream of the multiplex
signal (MPXRDS) and provides the signals clock (RDCL), data (RDDA) for further
processing by the integrated RDS decoder.
8.19.2 RDS data and clock direct
The RDS demodulator retrieves the RDS data and clock signals, this data can be put
directly onto pins VAFL and VAFR by setting bit RDSCDA to logic 1.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
10 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
8.19.2.1 RDS/RBDS decoder
The RDS decoder provides block synchronization, error correction and flywheel function
for reliable extraction of RDS or RBDS block data. Different modes of operation can be
selected to fit different application requirements. Availability of new data is signalled by bit
DAVFLG and output pin INTX which generates an interrupt. Up to two blocks of data and
status information are available via the I2C-bus in a single transmission.
The behavior of the DAVFLG is described in Section 10.
8.20 Audio pause detector
The audio pause detector monitors the audio modulation for pauses and responds to low
levels. The modulation threshold can be adjusted in 4 steps of 4 dB by control bits PL[1:0].
The minimum time for detecting a pause can be adjusted by control bits PT[1:0] as shown
in Table 38. When a pause occurs, flag PDFLAG is set to logic 1 and a hardware interrupt
is generated; see Section 9.1.4.6.
8.21 Auto search and Preset mode
In Search mode the TEA5764UK can search channels automatically (see Figure 3).
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
11 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
start
during a preset mute is always active
search mode is default not muted
unless AHLSI is set
reset flags
set PLL frequency
wait for PLL to settle
false
level OK
set LEVFLAG
true
false
IF OK
true
false
AHLSI
true
false
search mode
true
false
search up
true
increment current_pll
by 100 kHz
decrement current_pll
by 100 kHz
false
band limit
true
BLFLAG = 0
FRRFLAG = 1
no mute
BLFLAG = 0
FRRFLAG = 1
mute
BLFLAG = 1
FRRFLAG = 1
no mute
001aab461
Fig 3. Flowchart auto search or preset
Before starting a search or a preset, the INTMSK register must be reset and only the
FRRMSK must be set. This allows the microprocessor to be interrupted only when the
search or preset algorithm is ready.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
12 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
8.21.1 Search mode
Search mode is initiated by setting bit SM in byte FRQSETMSB to logic 1. The search
direction is set by bit SUD; SUD = 0 (search down), bit SUD = 1 (search up). The tuner
starts searching at the frequency set in bytes FRQSETLSB and FRQSETMSB. The
Search Stop Level (SSL) bits define the field strength level at which a desired channel is
detected. The tuner will stop on a channel with a field strength equal to or higher than this
reference level and then checks the IF frequency; when both are valid, the search stops
(Note that this depends on bit AHLSI described in Figure 3). If the level check or the
IF-count fails, the search continues. If no channels are found, the TEA5764UK stops
searching when it has reached the band limit, setting the BLFLAG HIGH. A search always
stops when the FRRFLAG is set and on the occurrence of a hardware interrupt, this
procedure is shown in Figure 3.
The search algorithm can stop at a frequency that is offset from the IF by up to a
maximum of 12 kHz. The maximum offset can be limited to 8 kHz by applying a preset.
For optimum tuning, it is recommended that a preset is applied after a search and when
the found frequency has an offset that is above 8 kHz.
After this interrupt the TEA5764UK will not update the tuner registers for a period of 15
ms. The state of the TEA5764UK can be checked by reading the bytes of INTFLAG,
FRQCHKMSB, FRQCHKLSB, TNCTRL1 and TNCTRL2. Table 4 shows the possible
states of these registers after an auto search.
Table 4:
IFFLAG BLFLAG FRRFLAG Comment
Tuner truth table[1]
0
0
0
if pin INTX has gone LOW and only IFMSK, FRRMSK and
BLMSK were set then this cannot occur
0
0
0
0
1
1
1
0
1
channel found during search / preset; FRRMSK set
not a valid state
a valid channel found and the band limit has been reached
during a search; BLMSK or FRRMSK set
1
1
0
0
0
1
not a valid state
a preset or search has occurred but the wanted channel has a
valid RSSI level but fails the IF count when AHLSI was set to
logic 1; HLSI must be toggled and a new PLL value must be
programmed; FRRMSK set
1
1
1
1
0
1
not a valid state
band limit is reached during search; no valid channel found;
BLMSK or FRRMSK set
[1] This table is valid until 30.6 ms after the tuning cycle has completed. It shows the outcome of the flag
register when a read is done after pin INTX goes LOW on condition that no mask bit other than FRRMSK is
set.
8.21.2 Preset mode
A preset occurs by setting bit SM to logic 0 and writing a frequency to byte FRQSETMSB.
The tuner jumps to the selected frequency and sets the FRRFLAG when it is ready.
After this interrupt the TEA5764UK will not update the tuner registers for a period of
15 ms. The state of the TEA5764UK can be checked by reading registers: INTFLAG,
FRQCHKLSB, FRQCHKMSB, TNCTRL1 and TNCTRL2. Table 4 shows the possible
states after a preset.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
13 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
8.21.3 Auto high-side and low-side injection stop switch
When a channel is searched or a preset is done, reception can sometimes improve when
injection is done at the other side of the wanted channel.
image on low-side
wanted channel
image on high-side
switch LO from high-side to low-side
001aab460
Fig 4. Switch LO from high-side injection to low-side injection using bit HLSI
The TEA5764UK has bit HLSI which toggles the injection of the local oscillator from
high-side (bit HLSI = 1) to low-side (bit HLSI = 0). When bit HLSI is toggled, a new PLL
setting must be sent to the TEA5764UK.
When bit AHLSI is set to logic 1, the search / preset algorithm will stop after a channel has
a valid RSSI level check but fails the IF count. The microprocessor can now respond by
toggling the HLSI switch and sending a new PLL value to the tuner.
8.21.4 Muting during search or preset
During a preset the tuner is always muted and this is implemented by the algorithm.
A search is not muted by default unless bit AFM = 1 or bit AHLSI = 1.
When bit AHLSI = 1 and the tuner stopped during a preset or a search because of a
wrong IF count, the tuner stays muted; this allows the microprocessor to switch from the
high to low setting quietly and wait for the new result.
The tuner is always muted if bit AFM = 1 and is independent of a search or a preset. A
search can be muted by setting bit AFM to logic 1 before a search is initiated and resetting
it to logic 0 when the tuner is ready (only set bit FRRMSK when initiating a search or
preset).
All these mute actions are done by blocking the audio signal inside the soft mute
attenuator, the audio output will keep its DC level and stay low-ohmic i.e. 50 Ω (a hard
mute set by bit MU will cause a plop).
8.22 RDS update/alternative frequency jump
A channel which transmits RDS data can have alternative channels which have the same
information. These alternative channel frequencies are in the RDS data, so the
microprocessor can read the alternative frequencies and store them in a memory.
The tuner can perform an RDS update. This is very similar to a preset, but with a 2 ms IF
count time. The tuner will jump to the alternative frequency and check the level and the IF
count using a 2 ms count time. When the RSSI level check is above the specified level and
the IF count result is within the limits, then the tuner will stay at the alternative frequency
and stay muted, the microprocessor can now decide what to do. If the alternative
frequency is not valid it will jump back to the frequency it came from.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
14 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
The algorithm will finish with the FRRFLAG being set and an interrupt is generated. After
this interrupt the TEA5764UK will not measure the IF count for a period of 15 ms. 15 ms
after completing a RDS jump, a measurement of the IF count will start and hence the IF
count result and the IFFLAG will be updated 30.6 ms after completing the algorithm. The
level measurement will start immediately after the tuning algorithm, so the LEVFLAG will
be updated 500 µs after the algorithm. The state of the TEA5764UK can be checked by
reading registers INTFLAG, FRQCHKLSB, FRQCHKMSB, IFCHK and LEVCHK. Table 5
shows the possible states after an auto search, Figure 5 is a flowchart showing how the
RDS is updated.
8.22.1 Muting during RDS update
An RDS update (AF jump) is always muted. There are two possibilities for leaving the
algorithm:
• The tuner jumps to an alternative frequency which is not valid (according to the
specified SSL limit and fixed IF counter limits) and jumps back, then it will
automatically unmute.
• Or the tuner jumps to a valid alternative frequency and stays there. Now it does not
unmute. The microprocessor can unmute or it keeps the tuner muted and can check
for the presence of RDS data. The valid way to unmute is to apply a preset to the
current frequency (an IF count time of 15.6 ms is used at preset, which gives a more
accurate IF count result than the result obtained by the AF jump, where 2 ms is used).
Table 5:
IFFLAG BLFLAG FRRFLAG Comment
RDS update truth table[1]
0
0
0
if pin INTX is LOW and only IFMSK, FRRMSK and BLMSK were
set then this cannot occur
0
0
1
alternative frequency jump successful; radio is tuned to the
alternative frequency and stays muted
0
0
1
1
1
1
0
0
0
1
0
1
not a valid state
not a valid state
not a valid state
AF jump has occurred but the wanted channel fails the IF count;
the PLL will be set back to the old value
1
1
1
1
0
1
not a valid state
if pin INTX is LOW and only IFMSK, FRRMSK and BLMSK were
set then this cannot occur
[1] This table is valid until 30.6 ms after an RDS update has completed. It shows the outcome of the flag
register when a read is done after pin INTX has gone LOW and on condition that only mask bit FRRMSK is
set.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
15 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
start
set IF count time
to 2 ms
activate mute
store 'old' PLL setting
clear LEVFLAG
clear IFFLAG
set PLL to AF frequency
wait for PLL to settle
false
level OK
true
wait for IF counter
set LEVFLAG
false
IF OK
true
reset 'old' PLL setting
wait for PLL to settle
FRRFLAG = 1
BLFLAG = 0
FRRFLAG = 1
BLFLAG = 0
keep mute
not mute
(PLL is AF frequency)
(PLL is old frequency)
001aab462
Fig 5. Flowchart RDS update
9. Interrupt handling
9.1 Interrupt register
The first two bytes of the I2C-bus register contain the interrupt masks and the interrupt
flags. A flag is set when it is a logic 1.
Table 6:
Bit
INTFLAG - byte0R
7
6
5
4
3
2
1
0
Symbol
DAVFLG
TESTBIT
LSYNCFLG
IFFLAG
LEVFLAG
PDFLAG
FRRFLAG
BLFLAG
Table 7:
Bit
INTMSK - byte0W / byte1R
7
6
5
4
3
2
1
0
Symbol
DAVMSK
-
LSYNCMSK
IFMSK
LEVMSK
PDMSK
FRRMSK
BLMSK
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
16 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
The interrupt flag register contains the flags set according to the behavior outlined in
Section 9.1.4. When these flags are set they can also cause the INTX to go active
(hardware interrupt line) depending on the status of the corresponding mask bit in Table 7.
A logic 1 in the mask register enables the hardware interrupt for that flag.
Hence, it is conceivable that, with all the mask bits cleared, the software could operate in
a continuous polling mode that reads the interrupt flag register for any bits that maybe set.
Interrupt mask bits are always cleared after reading the first two bytes of the interrupt
register. This is to control multiple hardware interrupts (see Figure 6). Bit LSYNCMSK has
a different function and is not cleared after reading the interrupt register bytes, see also
Section 9.1.4.3.
9.1.1 Interrupt clearing
The interrupt flag and mask bits are always cleared after:
• They have been read via the I2C-bus
• A power-on reset
9.1.2 Timing
The timing sequence for the general operation interrupts is shown in Figure 6 and shows
a read access of the interrupt bytes INTFLAG and INTMSK and a subsequent (though not
necessarily immediate) write to the mask register. It also indicates the two key timing
points A and B.
If an interrupt event occurs while the register is being accessed (after point A) it must be
held until after the mask register is cleared at the end of the read operation (point B).
Point A is after the R/W bit has been decoded and point B is where the acknowledge has
been received from the master after the first two bytes have been sent.
The LOW time for the INTX line (tLOW) has a maximum value specified in Section 14.
However it can be shorter if the read of the INTMSK and INTFLAG bytes occurs within
tLOW
.
9.1.3 Reset
A reset can be performed at any time by a simple read of the interrupt bytes, byte0R and
byte0W, which automatically clears the interrupt flags and masks.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
17 of 64
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
read access
INTFLAG
0R data
INTMSK
write access
INTMSK
0W data
FRQSETMSB FRQSETLSB
data
device
S
device
S
R
A
A
1R data
(2)
A
data
A
W
A
A
1W data
A
2W data
A
P
address
address
(1)
interrupt event
A
B
B
2
1
(3)
interrupt flag bit
interrupt mask bit
(4)
(6)
(5)
(5)
INTX
001aab464
(1) Interrupt events that occur outside of the region A-B set their respective flag bits in the normal way immediately and can thus trigger a hardware interrupt if the mask
bits are set.
(2) The blocking of interrupts is marked by the region A-B1 / B2 depending on the actual read cycle.
B1 is when only the INTFLAG is read and a stop condition is received (only INTFLAG is read so only this will be cleared).
B2 is when both registers are read and hence cleared and this is terminated by either an acknowledge or stop bit.
(3) Interrupt events that occur between A and B set their respective flags after the mask bits are cleared. Which means that in this diagram an interrupt event occurred in
period A-B, so after A-B the flag goes to logic 1.
(4) All interrupt mask bits are cleared after the interrupt flag and mask bytes are read.
(5) Software writes to the mask byte and enables the required mask bits. Any flags currently set will then trigger a hardware interrupt.
(6) INTX is set HIGH (inactive) after the interrupt mask bytes are read.
Fig 6. I2C-bus interrupt sequence, read and write operation
TEA5764UK
Philips Semiconductors
FM radio + RDS
9.1.4 Interrupt flags and behavior
9.1.4.1 Multiple interrupt events
If the interrupt mask register bit is set then the setting of an interrupt flag for that bit
causes a hardware interrupt (pin INTX goes LOW). If the event occurs again, before the
flag is cleared, then this does not trigger any further hardware interrupts until that specific
flag is cleared. However, two different events can occur in sequence and generate a
sequence of hardware interrupts. A second interrupt can be generated only after the
INTMSK byte is read, followed by a write as the first interrupt blocks the input of the INTX
one-shot generator.
If subsequent interrupts occur within the INTX LOW period then these do not cause the
INTX period to extend beyond its specified maximum period (see Section 9.2).
9.1.4.2 Data available flag
The DAVFLG is set when a new block of data is received according to the diagrams
shown in Section 10 where the different DAV modes are described. Once synchronized,
this continues for all subsequent received blocks (dependent on DAV mode) and in the
following situations:
• During sync search, in any DAV mode: two valid blocks in the correct sequence
received with BBC < BBL (synchronized).
• During synchronization search in DAVB mode if a valid A(C’)-block has been
detected. This mode can be used for fast search tuning (detection and comparison of
the PI code contained in the A or C’ block.
• If the pre-processor is synchronized and in mode DAVA and DAVB a new block has
been processed. This mode is the standard data processing mode if the decoder is
synchronized.
• If the pre-processor is synchronized and in DAVC mode, two new blocks have been
processed.
• If the decoder is synchronized and in any DAV mode, with LSYNCMSK = 0, loss of
synchronization is detected (flywheel loss of synchronization, resulting in a restart of
synchronization search).
The DAVFLG is reset by a read of RDSLBLSB (byte15R) or RDSPBLSB (byte17R). An
interrupt is asserted each time a new block of data is decoded and when bit DAVMSK is
set; for details see Section 10.
9.1.4.3 RDS synchronization flag
Bit SYNC, Table 29, shows the status of the RDS decoder. If it is a logic 1 then the
decoder is synchronized, if it is a logic 0 it is not.
The action of the TEA5764UK depends on the status of bit LSYNCMSK in Table 7. If this
is set then the loss of synchronization causes bit LSYNCFL to go to logic 1 when
synchronization is lost, and a hardware interrupt is asserted. The RDS part of the
TEA5764UK is set to idle and waits for the microprocessor to initiate a new
synchronization search by setting bit NWSY as described in Table 36.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
19 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
If bit LSYNCMSK is 0 and synchronization is lost, the ASIC automatically starts a new
synchronization search. It will not generate a hardware interrupt. The microprocessor can
wait until the RDS decoder is synchronized again, this will be indicated by the DAVFLG
and the SYNC status bit (this requires bit DAVMSK being set).
Bit LSYNCFL is reset by a read of the INTMSK byte1R.
Bit LSYNCMSK is not reset by a read of byte INTMSK, it must be set or reset by the
microprocessor. Resetting it automatically would change the status of the ASIC and cause
an automatic synchronization search as described above.
How the synchronization is defined is explained in brief in Section 10.
9.1.4.4 IF frequency flag
During an automatic frequency search, preset or AF update, the FM part of the
TEA5764UK performs a check of the received IF frequency as a measure of the level of
interference in the channel received. If an incorrect IF frequency is received, it indicates
the presence of either strong interferers or tuning to an image which sets bit IFFLAG in the
INTFLAG register. Also a preset to a channel with no signal will result in a wrong IF count
value and hence the setting of bit IFFLAG.
When a search, preset or AF update is finished, bit FRRFLAG will be set to indicate this
and will generate an interrupt. The microprocessor can now read the outcome of the
registers which will contain the IF count value and the IFFLAG status of the channel it is
tuned to. In the case of an AF update, the IF count value of the alternative frequency will
be in the registers and also when it jumps back, because it will then not start a new IF
count.
15 ms after the tuning algorithm has completed the IF counter will start a new count. So
30.6 ms after a failed AF update the IF count result will be equal again to that of the
channel from where the jump was initiated.
15 ms after the FRRFLAG has been set the IF counter will start to run continuously on the
tuned frequency and if the conditions for correct frequency are not met then this sets bit
IFFLAG in the interrupt register. When bit IFMSK is set this will also cause an interrupt.
Bit IFFLAG is cleared by a read of byte1R, or by starting the tuning algorithm.
9.1.4.5 RSSI threshold flag
The voltage level reflects the field strength received by the antenna. The voltage level is
analog to digital converted to a 4-bit value and output via the I2C-bus, this 4-bit level value
can be compared to a threshold level set by the SSL bits in Table 19 or the LH bits in
Table 26.
The ADC level (which converts the analog value to digital) can be triggered to convert in
either of two ways:
1. During a tuning step, a search, a preset or an AF update, it is triggered by these
algorithms and compares the level with the threshold set by bits SSL[1:0]. Bit
LEVFLAG is set if the RSSI level drops below the threshold level set by bits SSL[1:0]
(see Table 19). The hardware interrupt is only generated if the corresponding mask bit
is set.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
20 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
2. After a search, a preset or an AF update, the threshold for comparison is switched to
the hysteresis level. The hysteresis level is set by the combination of bits SSL[1:0] and
bit LHSW; see Table 24. The result is a hysteresis as shown in Table 26. Then the
ADC level starts to run automatically and compares the level every 500 µs with the
hysteresis level. Bit LEVFLAG is set if the RSSI level drops below the threshold level
set by bits SSL[1:0] in combination with bit LHSW (see Table 26); the hardware
interrupt is only generated if the corresponding mask bit is set. Bit LHSW allows either
a small or a large hysteresis to be selected which results in the levels of the left RSSI
hysteresis threshold column for bit LHSW = 0 and the right RSSI hysteresis threshold
column; see Table 26. When a search or preset is done with the ADC level set to 3
then when the algorithm has finished, the threshold level is set to 0. Hence the
LEVFLAG will never be set.
Bit LEVFLAG is cleared by a read of the INTMSK byte1R, or by starting the tuning
algorithm.
9.1.4.6 Pause detection flag
The pause detector monitors the amplitude of the audio signal and starts counting if it
drops below the reference level. When the counter reaches the specified count time, a
pause is detected and the PDFLAG is set and will generate an interrupt if bit PDMSK is
set to logic 1. The PDFLAG operates independently of bit PDMSK and is only active when
the RDS decoder is switched on when bit PUPD is set to logic 1 and when the RDS
decoder is not idle if synchronization is lost.
See Figure 7. When the peak audio level of the (L+R) drops below the threshold level at t1
it counts the duration of the pause. If the pause lasts longer than the value set by the PT
bits, bit PDFLAG is set which in turn generates a hardware interrupt (bit PDMSK set to
logic 1). The threshold level at t1 is set by the PL bits shown in Table 38.
Bit PDFLAG is cleared by a read of byte1R on condition that the read action occurs more
than 500 µs after receiving the pause interrupt on the INTX line.
The circuit should ignore short transients where the audio level momentarily rises above
the threshold (at t2).
A pause is detected by comparing the amplitude of the audio signal with the reference
level selected by the PL bits. The resultant signal PSCO produced by this comparison is
sampled at a frequency of 2341 Hz resulting in signal PSCOn. A pause is detected under
the conditions given by Equation 4 and Equation 5.
{SUM(0toN – 1)[PSCOn = 0] – 8 × SUM(0toN – 1)[PSCOn = 1]} > PT × 2341
tpause – 8 × taudio > PT
(4)
(5)
where N is the number of samples taken over time and PT is the pause time selected by
bus bits PT. When a pause is detected, the integrator will be reset. The integrator value
cannot be less than zero; therefore if in Equation 4, the value of the second SUM
becomes larger than the first SUM, the output of the integrator remains at zero.
Suppose that PT = 20 ms, tpause = 16 ms and taudio = 1.5 ms. The pause detector will
count according to Equation 5 as shown in Equation 6:
2 × tpause – 8 × taudio = 20 ms ≥ 2 × 16 ms – 8 × 1.5 ms = 20 ms
(6)
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
21 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
In Equation 6, the pause detector has measured 1 × 16 ms ‘pause’, 8 × 1.5 ms ‘no pause’
and 1 × 16 ms pause. Therefore on average the pause detector has measured 16 ms − 12
ms + 16 ms = 20 ms pause time and hence a pause will be detected.
The PSCOn signal goes directly to the software port. The PDFLAG is set by the integrator
and goes to the bus. The interrupt line is triggered by the PDFLAG.
+ reference level "PL" [mV] (1)
0
audio signal
− reference level "PL"
pause
PSCO
no pause
t
t
2
1
audio
PT x 2341
integrator
output
0
audio present
(2)
t
t
t
pause
pause
audio
PSCOn
no audio present
001aac795
PDFLAG
tnp(min) > 5 ms.
(1) The reference level is defined in kHz, but is internally transformed to mV e.g. 22.5 kHz = 75 mV; 1 kHz = 3.3 mV.
(2) The actual PSCO signal behaves as shown in the top diagram, in the bottom diagram it is assumed that all samples are
taken at peaks of the audio signal resulting in PSCOn.
Fig 7. Operation and timing of pause detection according to levels set in Table 38
9.1.4.7 Frequency ready flag
The frequency ready flag bit is set to logic 1 when the automatic tuning has finished a
search, a preset or an RDS AF update. This bit is described in Table 4 and Table 5. The
FRRFLAG is cleared by a read of byte1R.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
22 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
9.1.4.8 Band limit flag
The band limit bit BLFLAG is set to logic 1 when the automatic tuning has detected the
end of the tuning band or when the PLL cannot lock on a certain frequency. This bit is
described in Table 4 and Table 5. This bit is cleared by reading byte1R.
9.2 Interrupt output
The interrupt line driver is a MOS transistor with a nominal sink current of 680 µA, it is
pulled HIGH by an 18 kΩ resistor connected to pin VREFDIG. The interrupt line can be
connected to one other similar device with an interrupt output and an 18 kΩ pull-up
resistor providing a wired OR function. This allows any of the drivers to pull the line LOW
by sinking the current. When a flag is set and not masked it generates an interrupt; see
Figure 8.
V
CCA
(1)
flag
INTX
< 10 ms
read clears INTX
< 10 ms
10 ms
10 ms
read INTMSK
write INTMSK
001aab470
Read INTMSK clears flag, INTMSK and INTX.
Write INTMSK enables INTX.
When flag is set, the next interrupts are blocked until read / write INTMSK.
(1) Flag is set immediately after the reset, because event is still there.
Fig 8. Interrupt line behavior
10. RDS data processing
The RDS demodulator and decoder perform the following operations:
• Demodulation of the RDS/RDBS data stream from the MPX signal
• Symbol decoding
• Block and group synchronization
• Error detection and correction
• Store last and previous data block received with associated ID and error status
• Set the DAVFLG when new data is received
• Set the SYNC status bit according to the current synchronization state
• Set the LSYNCFL flag when synchronization is lost
The RDS decoder can be set to different modes, each meant to look for specific
information.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
23 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
10.1 DAV-A processing mode
The DAV-A processing mode is the standard processing mode used. In this mode, when a
data block has been decoded, it is transferred to the I2C-bus registers. It generates
interrupts on the INTX line after every new block of RDS data that has been processed
and also sets the DAVFLG; see Figure 9. The DAVFLG is reset by a read of the I2C-bus
registers.
If a data block is decoded and a new one arrives, pin INTX goes LOW again, the DAVFLG
will be set and the last block will be shifted to the previous block and the last decoded
block will be put in the last block. This means that all RDS data is still available in the BL
and BP registers.
When the I2C-bus registers are not read the DAVFLG will not be reset. If a data block is
decoded and a new one arrives, pin INTX goes LOW and the last block will be shifted to
the previous block and the last decoded block will be put in the last block. This means that
all RDS data is still available in the BL and BP registers but must be read. This is indicated
by the setting of bit DOVF.
If the I2C-bus registers are still not read, data will be lost, except when this read is done
within 20 ms after the INTX line has gone LOW and 2 ms before the arrival of a new block.
If this read is done at least 2 ms before the arrival of a new block, then BL and BP are read
and the data in the decoder buffer is then instantaneously shifted to the BL register. All
data is now read and bit DOVF will be reset.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
24 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
21.9 ms
read BL
read BL
read BL
A
B
C
1
D
1
A
B
C
2
1
1
2
2
DAVFLG set
on falling edge
DAVN = 0, cleared
on read BL register
DAVFLG
INTX
9.98 ms
9.98 ms
t
t
INT_RD
INT_RD < ≈ 10 ms
end read intmsk
read intflg + RDS on INTX
t
READ
> 2 ms
A
B
A
C
C
B
D
C
A
A
A
B
A
BL register
BP register
1
1
1
1
1
2
2
2
2
2
x
B
D
1
1
1
1
1
(1)
(3)
(2)
being decoded
decoder
registers:
B
A
C
D
C
A
A
B
B
1
1
1
1
2
2
2
1
2
2
in the decoder buffer
B
D
D
A
A
1
1
1
1
(4)
data overflow bit
(1)
(2)
(5)
001aab471
Bit DOVF set when 2 new blocks received in BL and BP registers
(1) If there is no read cycle, B1 is placed in the BP register and the new block C1 is now in the BL
register. Bit DOVF is set to indicate two blocks available.
(2) Data is not transferred to BL register at the end of the read period/clear DOVF, D1 is missed.
(3) In order not to lose D1 a read must be performed before D1 enters decoder buffer, thus read
finishes within 21 ms after DOVF set to logic 1.
(4) DOVF is cleared when the BL register is read. To be of use, DOVF has to be read before BL
and BP registers.
(5) To prevent DOVF being set again, an extra read of BL must be performed before A2 has been
decoded.
Fig 9. DAV-A timing diagram, DAV-A/B: normal
Figure 9 assumes that block synchronization has been achieved and that no other
interrupt flags are being set.
10.2 DAV-B processing mode / fast PI search mode
This mode is used, for example, when the receiver has been re-tuned to a new station,
and a fast search of the PI code, always contained in the A or C’ block, is required. The
diagram shown in Figure 10, assumes that the RDS decoder is unsynchronized initially
and is performing a synchronization search.
During synchronization search the decoder does not set the DAVFLG until a valid A or C’
block is detected. If a valid B block is detected immediately, then the decoder is now
synchronized and bit SYNC is set to logic 1. In fact, if any 2 good blocks in a valid order
are detected, the RDS decoder will synchronize and give an interrupt.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
25 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
If for some reason a valid B block was not received then the next valid A or C’ block is
decoded and the DAVFLG set. The BP and BL registers record the A block history.
When the decoder is synchronized, each decoded block will set the DAVFLG (assuming it
was reset by a read action) and generate an interrupt.
21.9 ms
B
C'
1
D
1
A
B
C
2
1
2
2
bad
good
bad
bad
good
good
good A or C' block detected
DAVFLG
INTX
read BL register
not synchronized
read intmsk
sync status bit
synchronized
Bus access - read
x
x
C'
C'
C'
B
C
B
BL register
BP register
1
1
1
2
2
x
x
x
C'
1
2
only valid blocks with no errors
are counted as good blocks
error correction applied
according to SYM bits
001aab472
When the number of blocks detected in the order: ‘bad’ ‘bad’ ‘good’ is 2, synchronization is
achieved if another good block followed by either 0, 1 or 2 bad blocks and another good block
are then received. If the order is 3 bad blocks, no synchronization is achieved and the counters
are reset.
The number of allowed bad clocks can be set using the BBG bits
Fig 10. DAV-A timing diagram, DAV B: with bad blocks detected during sync search
10.3 DAV-C reduced processing mode
The DAV-C processing mode is very similar to DAV-A mode with the main exception that a
data flag is set only after two new blocks are received. Hence the update rate is reduced
by half.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
26 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
21.9 ms
being
decoded
A
B
1
C
1
D
1
A
B
2
1
2
DAVFLG cleared at end read BP register
and forced to zero till end read of RDS 4R
DAVFLG
INTX
t
INTX cleared at end read INTMSK
BL register copied to
INTX
BP register and C to
1
BL register
B
copied to BL register shortly
t
1
INT_RD
before C decoded
1
read access
(case 1)
t
read
001aab473
Fig 11. Normal DAV-C timing diagram
21.9 ms
A
B
1
C
1
D
1
A
B
2
1
2
instant copy C from decoder buffer
1
to BL, and BL to BP just before D
decoded due to read action
1
D
C
A
C
D
A
2
BL register
BP register
0
1
1
1
1
D
A
C
D
1
0
0
1
instant copy of A
from decoder
buffer to BL, and
BL to BP
2
DAVFLG not cleared as no read performed
DAVFLG
(case 2)
DAVFLG reset when
st
1
new block
nd
DAVFLG set when 2 new block
in decoder buffer
would have been copied
INTX
t
= 10 ms
INTX
read access
(case 2)
(a)
t
read
no read on INTX
so B will be lost
dashed line shows what would happen if no read
occurred at (a). DOVF bit set until the next read of BP
register, however D1, A2 would be lost
1
data
overflow bit
2 new blocks have arrived in BL/BP (C , D ) and a new block (A )
1
1
2
has entered the decoder buffer. Hence, DOVF is set again.
To prevent this, an extra read must be performed after reading (a)
001aab474
Fig 12. DAV-C timing diagram, late read of BL, BP register
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
27 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
10.4 Synchronization
10.4.1 Conditions for synchronization
When the RDS decoder is turned on it must be synchronized to extract valid data from the
MPX signal. To do so the decoder automatically initiates a search for synchronization. The
conditions to meet synchronization and the status of this synchronization can be set and
checked by the following bits:
• BBL (Bad Blocks Lose): these bits can be set via the I2C-bus and have a value
between 0 to 63
• GBL (Good Blocks Lose): these bits can be set via the I2C-bus and have a value
between 0 to 63
• BBG (Bad Blocks Gain): these bits can be set via the I2C-bus and have a value
between 0 to 32
• GBC (Good Block Count): these bits can be read via the I2C-bus and have a value
between 0 to 63
• BBC (Bad Block Count): these bits can be read via the I2C-bus and have a value
between 0 to 63
When the decoder is not synchronized it will initiate a synchronization search. This
involves calculation of the syndrome for each block of 26 received bits on a bit-by-bit
basis. When a correct syndrome (and hence block ID) is received the decoder clocks the
next 26 bits into the internal registers and performs a second syndrome check.
Synchronization is found when a certain number of blocks have been decoded and two
good blocks have been found, this number of blocks is defined by the BBG bits. If the first
block needed for synchronization has been found and the expected second block (after
26 bits) is an invalid block, then the decoder module internal bad_blocks_counter is
incremented and the next expected block is calculated; exception: if RBDS mode is
selected and the first block is E, then the next expected block is always block A, until
synchronization is found or the maximum bad_blocks_counter value is reached. If the
decoder module internal bad_blocks_counter reaches the value of BBG[4:0], then a new
synchronization search (bit-by-bit) is started immediately to find a new first block.
The synchronization is monitored by two flywheel counters, GBC and BBC. These are
6-bit counters that can be preset by bits GBL and BBL to values between 0 and 63. Each
time a block is decoded and recognized as a bad block the Bad Block Counter value,
BBC, is incremented by 1. When the BBC value is equal to the BBL value, synchronization
is lost. Bit SYNC will become 0 and bit LSYNCFL is set to indicate the loss of
synchronization. The TEA5764UK will now automatically initiate a new synchronization
search.
Each time a good block is decoded, the GBC value is incremented. When the GBC value
is equal to the GBL value, both counters, BBC and GBC, are set to 0 and a new count
starts. The GBC counter is only incremented when the decoder is synchronized.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
28 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
10.4.2 Data overflow
During synchronization, after RDS data is read from the registers, new available blocks
are shifted to the registers as described in Section 10.1 to Section 10.3. If the registers
are not read in time, the decoder cannot shift any new available block to the registers and
hence a data overflow will occur, this is indicated by bit DOVF which is set to 1. Bit DOVF
is reset by a read of the registers or if bit NWSY = 1 which results in the start of a new
synchronization search.
Each time when a RDS data block is decoded, bit DAVN goes to logic 0 to indicate the
presence of a new data block. Bit DAVN also triggers the interrupt output INTX. In
principle the microprocessor must now start reading and must have read all RDS data
(byte12R to byte19R) before the arrival of a new RDS data block. In the application it is
possible that there is too large a delay between the arrival of a new block and reading this
block. This can have various causes such as a microprocessor that has to start-up from
Sleep mode or when polling is used instead of interrupt based read actions. Figure 13
shows the behavior of bit DAVFLG and bit DAVN when polling, where reading can occur at
any time. Note: Bit DAVN sets the INTX oneshot generator when DAVMSK = 1. Unlike
INTX, bit DAVN is not cleared by a read of the mask register.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
29 of 64
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
10.5 RDS flag behavior during read action
RDS data
A
B
C
D
A
B
C
10 ms
DAVN
(1)
DAVFLG
reset of DAVFLG
Read byte:
0R
0W
0R
0W 0R
(4)
0W
0R
0W
0R
0W 0R
0W
15R 19R
15R 19R
17R
15R 19R
17R
15R 19R
17R
15R 19R
17R
15R 19R
17R
(2)
(3)
17R
001aab475
Blocking DAVFLG: at end of reading byte15R or byte17R (DAV-A, B/C) DAVFLG is forced to zero. Only after reading byte19R DAVFLG is released again.
If synchronous reading is performed using ASIC generated interrupts, this problem does not occur.
To prevent undefined situations, byte12R to byte19R should always be read in one action immediately after each other.
Signal DAVN ≠ INTX.
(1) Normally reading byte19R would reset bit DAVN, but now it is reset after 10 ms, the maximal LOW time of bit DAVN.
(2) Read of byte15R in DAV-A and DAV-B mode clears DAVFLG. In DAV-C mode two consecutive RDS data blocks are read and hence DAVFLG is reset after reading
byte17R instead of byte15R (dotted line).
(3) Read of byte19R clears bit DAVN.
(4) Write byte0W (interrupt register).
Fig 13. RDS flag behavior
TEA5764UK
Philips Semiconductors
FM radio + RDS
10.6 Error detection and reporting
The TDA5764UK must report information on the number of errors corrected in the last and
previously decoded blocks. This is reported in bits ELB and EPB as shown in Table 29.
During synchronization search the error correction is disabled for detection of the first
block and is enabled for processing of the second block according to the mode set by the
SYM bits as described in Table 36.
10.7 RDS test modes
In Test mode the raw RDS clock and RDS data can be recovered directly from pins VAFL
and VAFR when bit RDSCDA = 1.
10.8 Reading RDS data from the registers
To read RDS data the microprocessor must read byte12R to byte19R. All 8 bytes must be
read to reset the status bytes 12R and 13R, i.e. effectively the status bits can be updated
by the decoder after reading the last bit of byte19R. Bit DOVF is cleared after reading the
last bit of byte19R and the status of bit SYNC does not depend on reading the register, bit
SYNC indicates if the decoder is synchronized or not. When starting a read action from
byte12R, the decoder blocks updates from the RDS bytes until byte19R has been read.
RDS byte12R to byte19R must be read in one read action.
11. I2C-bus interface
The I2C-bus interface is based on “The I2C-bus specification”, version 2.1 January 2000,
expanded by the following definitions.
11.1 Write and read mode
Table 8:
S
I2C-bus FM write mode
Byte 1
As Byte 2
As
Byte n
As
Byte 8
As
P
START chip address
0010 000
R/W ACK byte0W
ACK .....
ACK byte6W
xxxx xxxx
ACK STOP
0
xxxx xxxx
Table 9:
S
I2C-bus RDS write mode
Byte 1 As Byte 2
Am Byte n
As
Byte 8
As
P
START chip address
R/W ACK byte7W
ACK .....
ACK byte10W
non
STOP
ACK
0010 001
0
xxxx xxxx
xxxx xxxx
When writing all bytes, byte0W to byte10W can be written with one write action.
Table 10: I2C-bus FM read mode
S
Byte 1
As Byte 2
Am Byte n
Am Byte 17
NAm
P
START chip address
R/W ACK byte0R
ACK .....
ACK byte15R
non
STOP
ACK
0010 000
1
xxxx xxxx
xxxx xxxx
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
31 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 11: I2C-bus RDS read mode
S
Byte 1
As Byte 2
Am Byte n
Am Byte 17
NAm
P
START chip address
R/W ACK byte12R
ACK .....
ACK byte27R
non
STOP
ACK
0010 001
1
xxxx xxxx
xxxx xxxx
Table 12: I2C-bus transfer description
Label
S
Definition
START condition
Byte 1
I2C-bus chip address (7 bits)
R/W = 0 for write action and R/W = 1 for read action
acknowledge from slave TEA5764UK (SDA is LOW)
data byte (8 bits)
As
Byte 2, etc.
P
STOP condition
Am
NAm
NA
acknowledge from master microcontroller (SDA is LOW)
non acknowledge from master microcontroller (SDA is HIGH)
non acknowledge (SDA is HIGH)
When the TEA5764UK is addressed by the FM radio address, the RDS part (byte12R to
byte27R) can be read in one read action. A read does not have to stop at byte11R.
Therefore, by effectively only using the RDS part of the address, ignores some bytes
which reduces I2C-bus access.
11.2 Data transfer
Structure of the I2C-bus:
• Slave transceiver
• Subaddresses not used
• Maximum LOW-level input voltage: VIL = 0.3 × VVREFDIG
• Minimum HIGH-level input voltage: VIH = 0.7 × VVREFDIG
Remark: The I2C-bus operates at a maximum clock rate of 400 kHz. It is not allowed to
connect the TEA5764UK to a I2C-bus operating at a higher clock rate.
Data transfer to the IC:
• Bit 7 of each byte is considered the MSB and has to be transferred as the first bit of
the byte
• The LSB indicates the write or read action
• The data becomes valid byte-wise at the appropriate falling edge of the SCL clock
• A STOP condition after any byte can shorten transmission times. When writing to the
transceiver by using the STOP condition before completion of the whole transfer:
– The remaining bytes will contain the old information
– If the transfer of a byte is not completed the new bits will be used, but a new tuning
cycle will not be started
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
32 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
To speed up RDS traffic it is possible to read all the RDS data and then only write back
byte INTMSK to set the appropriate mask(s) again.
I2C-bus activity:
• With bits PUPD the TEA5764UK can be switched in a low current Standby mode. The
I2C-bus is then still active
• When the I2C-bus interface is deactivated, by making pin BUSENABLE LOW and
without programmed Standby mode, the TEA5764UK keeps its normal operation, but
is isolated from the I2C-bus lines
• It is possible to operate the TEA5764UK with BUSENABLE hard wired to pin
VREFDIG, and have the bus interface always active.
SDA
SCL
t
f
t
BUF
t
r
t
P
P
S
Sr
t
SU;STO
t
t
t
t
t
SU;STA
HD;STA
SU;DAT
HD;DAT
HIGH
LOW
t
t
HO;BUSEN
SU;BUSEN
BUS
ENABLE
001aac796
tf = fall time of both SDA and SCL signals: 20 + 0.1 Cb < tf < 300 ns, where Cb = total capacitance on bus line in pF.
tr = rise time of both SDA and SCL signals: 20 + 0.1 Cb < tf < 300 ns, where Cb = total capacitance on bus line in pF.
tHD;STA = hold time (repeated) START condition. After this period, the first clock pulse is generated: > 600 ns.
tHIGH = HIGH period of the SCL clock: > 600 ns.
tSU;STA = setup time for a repeated START condition: > 600 ns.
tHD;DAT = data hold time: 300 < tHD;DAT < 900 ns.
Remark: 300 ns lower limit is added because the ASIC has no internal hold time for the SDA signal.
tSU;DAT = data setup time: tSU;DAT > 100 ns. If ASIC is used in a standard mode I2C-bus system, tSU;DAT > 250 ns.
tSU;STO = setup time for STOP condition: > 600 ns.
tBUF = bus free time between a STOP and a START condition: > 600 ns.
Cb = capacitive load of one bus line: < 400 pF.
tSU;BUSEN = bus enable setup time: tSU;BUSEN > 10 µs.
tHO;BUSEN = bus enable hold time: tHO:BUSEN > 10 µs.
Fig 14. Bus timing diagram
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
33 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
11.3 Register map
Table 13: Register overview
Byte
Read
0R
Byte name
Access
Reset value
Reference
Write
INTFLAG
INTMSK
R
00
00
80
00
08
D2
-
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 28
Table 29
Table 30
Table 31
Table 32
Table 33
Table 34
Table 35
Table 36
Table 37
Table 38
Table 39
Table 40
Table 41
Table 42
Table 43
1R
0W
1W
2W
3W
4W
R/W
2R
FRQSETMSB R/W
FRQSETLSB R/W
3R
4R
TNCTRL1
TNCTRL2
FRQCHKMSB
FRQCHKLSB
IFCHK
R/W
R/W
R
5R
6R
7R
R
-
8R
R
-
9R
LEVCHK
R
-
10R
11R
12R
13R
14R
15R
16R
17R
18R
19R
20R
21R
22R
23R
24R
25R
26R
27R
5W
6W
TESTBITS
TESTMODE
RDSSTAT1
RDSSTAT2
RDSLBMSB
RDSLBLSB
RDSPBMSB
RDSPBLSB
RDSBBC
R/W
R/W
R
00
00
-
R
-
R
-
R
-
R
-
R
-
R
-
RDSGBC
R
-
7W
8W
9W
10W
RDSCTRL1
RDSCTRL2
PAUSEDET
RDSBBL
R/W
R/W
R/W
R/W
R
00
10
00
00
50
2B
57
64
MANID1
MANID2
R
CHIPID1
R
CHPID2
R
11.4 Byte description
Table 14: INTFLAG - byte0R description
Bit
7
Symbol
DAVFLG
TESTBIT
LSYNCFL
IFFLAG
Access
Reset
Functional description
1 = RDS data is available
internal use
R
R
R
R
0
0
0
0
6
5
1 = synchronization is lost
1 = IF count is not correct
4
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
34 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 14: INTFLAG - byte0R description …continued
Bit
Symbol
Access
Reset
Functional description
3
LEVFLAG
R
0
continuous checking of the RSSI level
1 = RSSI level has dropped below (VSSL[1:0]
− Vhys
)
during a tuning period (preset or search)
1 = RSSI level has dropped below VSSL[1:0]
1 = pause is detected
2
1
0
PDFLAG
FRRFLAG
BLFLAG
R
R
R
0
0
0
1 = tuner state machine is ready
1 = during a search the band limit has been
reached or time out
Table 15: INTMSK - byte1R and byte0W description
Bit
7
Symbol
DAVMSK
-
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
Functional description
masks bit DAVFLG
reserved
0
0
0
0
0
0
0
0
6
5
LSYMSK
IFMSK
LEVMSK
PDMSK
FRMSK
BLMSK
masks bit LSYNCFL
masks bit IFFLAG
masks bit LEVFLAG
masks bit PDFLAG
masks bit FRRFLAG
masks bit BLFLAG
4
3
2
1
0
Table 16: FRQSETMSB - byte2R and byte1W description
Bit
Symbol
Access
Reset
Functional description
1 = search up
7
SUD
R/W
1
0 = search down
6
SM
R/W
0
1 = Search mode
0 = Preset mode
5
4
3
2
1
0
FR13
FR12
FR11
FR10
FR09
FR08
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
PLL frequency set bits; see Section 8.5
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
35 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 17: FRQSETLSB - byte3R and byte2W description
Bit
7
Symbol
FR07
FR06
FR05
FR04
FR03
FR02
FR01
FR00
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
Functional description
PLL frequency set bits; see Section 8.5
0
0
0
0
0
0
0
0
6
5
4
3
2
1
0
Table 18: TNCTRL1 - byte4R and byte3W description
Bit
Symbol
Access
Reset
Functional description
power-up and power-down
00 = FM off and RDS off
01 = FM on and RDS off
10 = not used
7 and 6
PUPD[1:0] R/W
00
11 = FM on and RDS on
1 = Japan FM band 76 MHz to 90 MHz
5
BLIM
R/W
0
0 = US / Europe FM band 87.5 MHz to
108 MHz
4
3
2
1
0
SWPM
IFCTC
AFM
R/W
R/W
R/W
R/W
R/W
0
1
0
0
0
1 = software port is output of FRRFLAG
0 = SWP
1 = IF count time = 15.02 ms
0 = IF count time = 2.02 ms
1 = left and right audio muted
0 = audio not muted
SMUTE
SNC
1 = soft mute on
0 = soft mute off
1 = stereo noise cancellation on
0 = stereo noise cancellation off
Table 19: TNCTRL2 - byte5R and byte4W description
Bit
Symbol
Access
Reset
Functional description
1 = left and right audio hard-muted
0 = no hard mute
search stop level
00 = ADC3
7
MU
R/W
1
6 and 5
SSL[1:0]
R/W
R/W
10
01 = ADC5
10 = ADC7
11 = ADC10
4
HLSI
1
1 = high-side injection
0 = low-side injection
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
36 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 19: TNCTRL2 - byte5R and byte4W description …continued
Bit
Symbol
Access
Reset
Functional description
3
MST
R/W
0
1 = forced mono
0 = stereo on
2
1
0
SWP
DTC
R/W
R/W
R/W
0
1
0
1 = pin SWPORT is HIGH
0 = pin SWPORT is LOW
1 = de-emphasis time constant = 50 µs
0 = de-emphasis time constant = 75 µs
AHLSI
see Section 8.21.3 for the functionality of
this bit
Table 20: FRQCHKMSB - byte6R description
Bit
Symbol
-
Access
Reset
Functional description
reserved
7 and 6
-
-
-
-
-
-
-
-
5
4
3
2
1
0
PLL13
PLL12
PLL11
PLL10
PLL09
PLL08
R
R
R
R
R
R
output frequency MSB
output frequency
output frequency
output frequency
output frequency
output frequency
Table 21: FRQCHKLSB - byte7R description
Bit
7
Symbol
PLL07
PLL06
PLL05
PLL04
PLL03
PLL02
PLL01
PLL00
Access
Reset
Functional description
output frequency
output frequency
output frequency
output frequency
output frequency
output frequency
output frequency
output frequency LSB
R
R
R
R
R
R
R
R
-
-
-
-
-
-
-
-
6
5
4
3
2
1
0
Table 22: IFCHK - byteR8 description
Bit
7
Symbol
IF6
IF5
IF4
IF3
IF2
IF1
IF0
-
Access
Reset
Functional description
IF count MSB
IF count
R
R
R
R
R
R
R
-
-
-
-
-
-
-
-
-
6
5
IF count
4
IF count
3
IF count
2
IF count
1
IF count LSB
reserved
0
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
37 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 23: LEVCHK - byte9R description
Bit
7
Symbol
LEV3
LEV2
LEV1
LEV0
LD
Access
Reset
Functional description
R
R
R
R
R
-
-
-
-
-
level count MSB
level count bit
6
5
level count bit
4
level count LSB
1 = PLL is locked
0 = PLL is not locked
1 = pilot detected[1]
0 = no pilot detected
reserved
3
2
STEREO
-
R
-
-
-
1 and 0
[1] This bit does not switch the radio to mono or stereo, this depends on the RF input level as shown in sections
‘Mono stereo blend’ or ‘mono stereo switched’ in Table 46.
Table 24: TESTBITS - byte10R and byte5W description
Bit
Symbol
Access
Reset
Functional description
7
LHM
R/W
0
1 = left audio output is hard muted
0 = left audio output is not hard muted
1 = right audio output is hard muted
0 = right audio output is not hard muted
6
5
RHM
R/W
R/W
0
0
RDSCDA
1 = pin VAFL is RDS clock and pin VAFR is
RDS data
0 = normal operation
4
3
LHSW
R/W
R/W
0
0
1 = level hysteresis is large
0 = level hysteresis is small
TRIGFR
1 = reference frequency selected pin
FREQIN
0 = crystal as reference pin XTAL
1 = local DX on, −6 dB gain of LNA
0 = local DX off, LNA has normal gain
1 = RFAGC off
2
1
0
LDX
R/W
R/W
R/W
0
0
0
RFAGC
INTCTRL
0 = RFAGC on
when this bit is set to logic 1 an interrupt is
generated on pin INTX
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
38 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 25: TESTMODE - byte11R and byte6W description
Bit
7 to 5
4
Symbol
Access
R/W
Reset
Functional description
-
0
0
reserved
TM
R/W
1 = oscillator output and programmable
divider output are enabled
0 = normal operation
3
2
1
0
TB3
TB2
TB1
TB0
R/W
R/W
R/W
R/W
0
0
0
0
test bits: Table 27 describes selection of
signals output to the SWPORT when
SWPM = 0; when TM = 1; TB[3:0] = 0;
which effectively is an AND function.
Table 26: LH - RSSI level hysteresis
RSSI ADC search stop level
RSSI hysteresis threshold
LHSW = 0
LHSW = 1
3
0
2
4
7
0
1
3
5
5
7
10
Table 27: Test bits (SWPM = 0)
TB3
0
TB2
0
TB1
0
TB0
0
SWPORT output signal
bit SWP of byte4W, depending on bits SWPM and SWP
0
0
0
1
oscillator output 32.768 kHz; when TM = 1
lock detect bit LD
stereo bit STEREO
programmable divider; when TM = 1
PSCOn; see Section 9.1.4.6
57 kHz clock
0
0
1
0
0
0
1
1
0
1
0
0
0
1
0
1
0
1
1
0
0
1
1
1
3-state
1
0
0
0
output of RDS comparator
reserved
1
0
0
1
1
0
1
0
reserved
1
0
1
1
reserved
1
1
0
0
reserved
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
39 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 28: RDSSTAT1 - byte12R description
Bit
7
Symbol
-
Access
Reset
Functional description
-
-
-
reserved
6 to 4
BLID[2:0]
R
block ID of last block
000 = A
001 = B
010 = C
011 = D
100 = C’
101 = E
110 = invalid block E (RBDS)
111 = invalid block
reserved
3 and 2
1 to 0
-
-
-
-
ELB[1:0]
R
number of errors for last processed block
00 = no errors
01 = maximum 2 bits
10 = maximum 5 bits
11 = uncorrectable
Table 29: RDSTAT2 - byte13R description
Bit
Symbol
Access
Reset
Functional description
block ID of previous block
000 = A
7 to 5
BPID[2:0]
R
-
001 = B
010 = C
011 = D
100 = C’
101 = E
110 = invalid block E (RBDS)
111 = invalid block
4 and 3
EPB[1:0]
R
-
number of errors for previous processed
block
00 = no errors
01 = maximum 2 bits
10 = maximum 5 bits
11 = uncorrectable
2
1
0
SYNC
RSTD
DOVF
R
R
R
-
-
-
1 = RDS bitstream is synchronized
0 = not synchronized
1 = power-on reset detected
0 = no power-on reset detected
1 = data overflow occurred during read
operation
0 = normal operation
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
40 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 30: RDSRLBMSB - byte14R description
Bit
7
Symbol
BL15
BL14
BL13
BL12
BL11
BL10
BL9
Access
Reset
Functional description
R
R
R
R
R
R
R
R
-
-
-
-
-
-
-
-
last RDS data byte - MSB
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte
6
5
4
3
2
1
0
BL8
Table 31: RDSLBLSB - byte15R description
Bit
7
Symbol
BL7
Access
Reset
Functional description
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte
last RDS data byte - LSB
R
R
R
R
R
R
R
R
-
-
-
-
-
-
-
-
6
BL6
5
BL5
4
BL4
3
BL3
2
BL2
1
BL1
0
BL0
Table 32: RDSPBMSB - byte16R description
Bit
7
Symbol
BP15
BP14
BP13
BP12
BP11
BP10
BP9
Access
Reset
Functional description
previous RDS data byte - MSB
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte
R
R
R
R
R
R
R
R
-
-
-
-
-
-
-
-
6
5
4
3
2
1
0
BP8
Table 33: RDSPBLSB - byte17R description
Bit
7
Symbol
BP7
Access
Reset
Functional description
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte
previous RDS data byte - LSB
R
R
R
R
R
R
R
R
-
-
-
-
-
-
-
-
6
BP6
5
BP5
4
BP4
3
BP3
2
BP2
1
BP1
0
BP0
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
41 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 34: RDSBBC - byte18R description
Bit
7
Symbol
BBC5
BBC4
BBC3
BBC2
BBC1
BBC0
GBC5
GBC4
Access
Reset
Functional description
R
R
R
R
R
R
R
R
-
-
-
-
-
-
-
-
bad block count MSB
bad block count
6
5
bad block count
4
bad block count
3
bad block count
2
bad block count LSB
good block count MSB
good block count
1
0
Table 35: RDSGBC - byte19R description
Bit
Symbol
GBC3
GBC2
GBC1
GBC0
-
Access
Reset
Functional description
good block count
good block count
good block count
good block count LSB
reserved
7
R
R
R
R
-
-
-
-
-
-
6
5
4
3 to 0
Table 36: RDSCTRL1 - byte20R and byte7W description
Bit
Symbol
Access
Reset
Functional description
1 = start new synchronization
0 = normal processing
error correction
7
NWSY
R/W
0
6 and 5
SYM[1:0]
R/W
00
00 = no correction
01 = maximum 2 bits
10 = maximum 5 bits
11 = no correction
1 = RBDS processing mode
0 = RDS processing mode
RDS data output mode
00 = DAVA
4
RBDS
R/W
R/W
0
3 and 2
DAC[1:0]
00
01 = DAVB
10 = DAVC
11 = not used
1 and 0
-
-
-
reserved
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
42 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 37: RDSCTRL2 - byte21R and byte8W description
Bit
Symbol
-
Access
-
Reset
Functional description
7 to 5
-
reserved
4
3
2
1
0
BBG4
BBG3
BBG2
BBG1
BBG0
R/W
R/W
R/W
R/W
R/W
1
0
0
0
0
bad blocks gain MSB
bad blocks gain
bad blocks gain
bad blocks gain
bad blocks gain LSB
Table 38: PAUSEDET - byte22R and byte9W description
Bit
Symbol
Access
Reset
Functional description
pause time
7 and 6
PT[1:0]
R/W
00
00 = 20 ms
01 = 40 ms
10 = 80 ms
11 = 160 ms
5 and 4
PL[1:0]
R/W
00
pause level L = R
00 = 1 kHz
01 = 1.6 kHz
10 = 2.5 kHz
11 = 4.0 kHz
3
2
1
0
GBL5
GBL4
GBL3
GBL2
R/W
R/W
R/W
R/W
0
0
0
0
number of good blocks lose MSB
number of good blocks lose
number of good blocks lose
number of good blocks lose
Table 39: RDSBBL - byte23R and byte10W description
Bit
7
Symbol
GBL1
GBL0
BBL5
BBL4
BBL3
BBL2
BBL1
BBL0
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
Functional description
0
0
0
0
0
0
0
0
number of good blocks lose
number of good blocks lose LSB
number of bad blocks lose MSB
number of bad blocks lose
number of bad blocks lose
number of bad blocks lose
number of bad blocks lose
number of bad blocks lose LSB
6
5
4
3
2
1
0
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
43 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 40: MANID1 - byte24R description
Bit
7
Symbol
Access
Reset
Functional description
VERSION3
VERSION2
VERSION1
VERSION0
MANID10
MANID9
R
R
R
R
R
R
R
R
0
1
0
1
0
0
0
0
version code MSB
version code
6
5
version code
4
version code LSB
manufacturer ID code MSB
manufacturer ID code
manufacturer ID code
manufacturer ID code
3
2
1
MANID8
0
MANID7
Table 41: MANID2 - byte25R description
Bit
7
Symbol
MANID6
MANID5
MANID4
MANID3
MANID2
MANID1
MANID0
IDAV
Access
Reset
Functional description
manufacturer ID code
R
R
R
R
R
R
R
R
0
0
1
0
1
0
1
1
6
manufacturer ID code
5
manufacturer ID code
4
manufacturer ID code
3
manufacturer ID code
2
manufacturer ID code
1
manufacturer ID code LSB
1 = manufacturer ID available
0 = no manufacturer ID available
0
Table 42: CHIPID1 - byte26R description
Bit
7
Symbol
Access
Reset
Functional description
chip identification code MSB
chip identification code
chip identification code
chip identification code
chip identification code
chip identification code
chip identification code
chip identification code
CHIP ID15
CHIP ID14
CHIP ID13
CHIP ID12
CHIP ID11
CHIP ID10
CHIP ID9
CHIP ID8
R
R
R
R
R
R
R
R
0
1
0
1
0
1
1
1
6
5
4
3
2
1
0
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
44 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 43: CHIPID2 - byte27R description
Bit
7
Symbol
Access
Reset
Functional description
CHIP ID7
CHIP ID6
CHIP ID5
CHIP ID4
CHIP ID3
CHIP ID2
CHIP ID1
CHIP ID0
R
R
R
R
R
R
R
R
0
1
1
0
0
1
0
0
chip identification code
chip identification code
chip identification code
chip identification code
chip identification code
chip identification code
chip identification code
chip identification code LSB
6
5
4
3
2
1
0
12. Limiting values
Table 44: Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
VLO1
Parameter
Conditions
Min
Max
+8
Unit
V
VCO tuned circuit output 1
VCO tuned circuit output 2
digital supply voltage
analog supply voltage
−0.3
−0.3
−0.3
−0.3
−0.3
VLO2
+8
V
VCCD
VCCA
+5.5
+8
V
V
VI/O(n)
voltage on all inputs and
outputs
with respect to ground
+5.5
V
Tstg
storage temperature
ambient temperature
−55
+150
+85
°C
°C
V
Tamb
Vesd
−40
[1]
electrostatic discharge voltage MM
HBM
all pins except PILLP, RFIN1, RFIN2
pin PILLP only
pins RFIN1 and RFIN2
−200
+200
[2]
[2]
[2]
−2000
−1000
−1500
+2000
+2000
+2000
V
V
V
[1] Machine model I (L = 0.75 mH, R = 10 Ω, C = 200 pF).
[2] Human body model (R = 1.5 kΩ, C = 100 pF).
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
45 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
13. Static characteristics
Table 45: Characteristics
The minimum and maximum values include spread due to VCCA = VCCD = 2.5 V to 3.3 V and Tamb = −20 °C to +85 °C; unless
otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Supply voltages
VCCA
VCCD
analog supply voltage
digital supply voltage
2.5
2.7
2.7
1.8
3.3
V
V
V
2.5
3.3
VVREFDIG digital reference voltage for
I2C-bus interface on pin
VREFDIG
1.65
VCCD
Supply currents
ICCA
analog supply current
VCCA = 2.5 V to 3.3 V
operating mode
Standby mode
12
0
13.7
0.1
16
1
mA
µA
ICCD
digital supply current
VCCD = 2.5 V to 3.3 V
operating mode
Standby mode
0.3
1
0.7
15
1.5
22.5
1
mA
µA
µA
IVREFDIG
digital reference supply current operating mode;
0
0.5
VVREFDIG = 1.65 V to VCCD
DC operating points
VLOOPSW voltage on pin LOOPSW
V
CD3 − 0.2
-
VCD3
V
VCPOUT
VLO1
voltage on pin CPOUT
voltage on pin LO1
voltage on pin LO2
voltage on pin PILLP
voltage on pin TMUTE
0.1
-
V
CD3 − 0.1
V
V
V
CD3 − 0.1
CD3 − 0.1
-
VCD3
VCD3
1.65
0.8
V
VLO2
-
V
VPILLP
VTMUTE
1.09
0.6
1.37
0.7
V
VRF = 0 V, measured with
respect to pin CD3
mV
VVAFL
VVAFR
voltage on pin VAFL
voltage on pin VAFR
fRF = 98 MHz; VRF = 1 mV;
no modulation
800
800
830
0.2
850
850
900
0.4
940
940
950
0.5
mV
mV
mV
V
fRF = 98 MHz; VRF = 1 mV;
no modulation
VMPXOUT voltage on pin MPXOUT
fRF = 98 MHz; VRF = 1 mV;
no modulation
VMPXIN
voltage on pin MPXIN
voltage on pin FREQIN
fRF = 98 MHz; VRF = 1 mV;
no modulation
VFREQIN
TRIGFR = 1
TRIGFR = 0
TRIGFR = 1
TRIGFR = 0
1.3
0
1.5
1.7
0.1
1.3
1.2
680
680
2
V
0.05
1.17
1
V
VXTAL
voltage on pin XTAL to CD3
0.9
0.8
420
420
1
V
V
VRFIN1
VRFIN2
VCAGC
voltage on pin RFIN1
voltage on pin RFIN2
voltage on pin CAGC
530
530
1.57
mV
mV
V
VRF = 0 V
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
46 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
14. Dynamic characteristics
Table 46: Characteristics
See Figure 1; all AC values are given in RMS; the minimum and maximum values include spread due to VCCA = VCCD = 2.5 V
to 3.3 V and Tamb = −20 °C to +85 °C; unless otherwise specified. All RF input values are defined in potential difference,
except when EMF is explicitly stated.
Symbol
Voltage controlled oscillator
fosc oscillator frequency
Reference frequency input; pin FREQIN
Parameter
Conditions
Min
Typ
Max
Unit
150
-
217
MHz
Ri
input resistance
500
5
-
-
kΩ
pF
Ci
input capacitance
resonance frequency
6
7
frsn
∆frsn
-
32.768
-
kHz
ppm
ppm
%
resonance frequency deviation Tamb = 25 °C
Tamb = −20 °C to +85 °C
square wave
−20
−150
30
-
-
-
-
-
-
+20
+150
70
VCC
0.55
-
δ
duty cycle
VIH
VIL
C/N
HIGH-level input voltage
LOW-level input voltage
carrier-to-noise ratio
square wave
square wave
at 10 kHz
1.15
0
V
V
−151
dBc/
Hz
Crystal oscillator 32.768 kHz; pin XTAL
frsn
resonance frequency
resonance frequency deviation
shunt capacitance
Tamb = 25 °C
-
32.768
-
kHz
ppm
pF
∆frsn
Cshunt
Cm
−20
-
-
-
-
-
+20
3.5
3.0
75
motional capacitance
series resistance
1.5
-
fF
Rs
kΩ
Synthesizer
Programmable divider
D/Dprog
programmable divider ratio
FRQSETMSB[15:8] = XX11
1111; FRQSETLSB[7:0] =
1111 1110
-
-
8191
FRQSETMSB[15:8] = XX00
1000; FRQSETLSB[7:0] =
0000 0000
2048
-
-
-
Dstep(prog) programmable divider step size
-
1
Charge pump; pin CPOUT; VLOOPSW = 0.2 V to (VLO2 − 0.2) V; fVCO > fref × divider ratio
IM(sink)
IM(source)
IF counter
N
peak sink current
250
250
500
500
1000
1000
nA
nA
peak source current
length
-
7
-
bit
Vsens
ncount
T
sensitivity voltage
count result for search stop
period
-
5.5
15
3C
-
µV
Hex
µs
10 µV < VRF < 1 V
IFCTC = 1
31
-
-
15625
1953
4096
IFCTC = 0
-
-
µs
fres
frequency resolution
-
-
Hz
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
47 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 46: Characteristics …continued
See Figure 1; all AC values are given in RMS; the minimum and maximum values include spread due to VCCA = VCCD = 2.5 V
to 3.3 V and Tamb = −20 °C to +85 °C; unless otherwise specified. All RF input values are defined in potential difference,
except when EMF is explicitly stated.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Logic pins; pins BUSENABLE, SCL and SDA
Ri
input resistance
10
-
-
-
MΩ
VIH
HIGH-level input voltage
input switching level up
0.7VVREFDIG
VVREFDIG
0.3
+
V
VIL
LOW-level input voltage
input switching level down
−0.3
-
-
0.3VVREFDIG
V
V
Software programmable port; pin SWPORT
VO(max)
maximum output voltage
Iload = 150 µA
VVREFDIG
0.2
−
VVREFDIG
VO(min)
minimum output voltage
maximum sink current
Iload = 150 µA
0
-
-
-
-
0.2
V
Isink(max)
400
500
−1.0
2000
1100
+1.0
µA
µA
µA
Isource(max) maximum source current
IL(max) maximum leakage current
VSWPORT = 0 V to 5 V
Interrupt flag; pin INTX; VVREFDIG = 1.65 V to 1.95 V; Iload(max) = 200 µA or Rpu of second device connected to pin
INTX is 18 kΩ ± 20 %
VO(max)
maximum output voltage
VVREFDIG
0.2
−
-
VVREFDIG
V
VO(min)
Ipd
minimum output voltage
pull-down current
pull-up resistance
LOW time
0.130
500
0.215
680
18
0.4
V
1200
22.5
10
µA
kΩ
ms
Rpu
tL
14.4
9.9
one-shot pulse time
9.98
Table 47: FM signal channel characteristics
See Figure 1; all AC values are given in RMS; the min. and max. values include spread due to VCCA = VCCD = 2.5 V to 3.3 V
and Tamb = −20 °C to +85 °C; unless otherwise specified. All RF input values are defined in potential difference, except when
EMF is explicitly stated.
Symbol
Parameter
Conditions
Min Typ Max Unit
FM RF input; pins RFIN1 and RFIN2
Ri
input resistance
connected to pin GNDRF
connected to pin GNDRF
75
2.5
-
100 125
Ω
Ci
input capacitance
4
6
pF
µV
Vsens(EMF)
sensitivity EMF value voltage fRF = 76 MHz to 108 MHz;
∆f = 22.5 kHz; fmod = 1 kHz;
2.9
4.4
(S+N)/N = 26 dB; TCdeem= 75 µs;
A-weighting filter;
B
aud = 300 Hz to 15 kHz
∆f1 = 200 kHz; ∆f2 = 400 kHz;
tune = 76 MHz to 108 MHz; RFagc = off
∆f1 = 4 MHz; ∆f2 = 8 MHz;
tune = 76 MHz to 108 MHz; RFagc = off
IP3in
in-band 3rd-order intercept
point
78
87
87
93
-
-
dBµV
dBµV
f
IP3out
out-of-band 3rd-order
intercept point
f
In-band AGC
Vi(AGC)(min)
minimum RF AGC input
voltage
fRF = 98 MHz; ∆Vth(mute)
∆Vsens(EMF) < 4 mV/dBµV
/
55
61
67
dBµV
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
48 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 47: FM signal channel characteristics …continued
See Figure 1; all AC values are given in RMS; the min. and max. values include spread due to VCCA = VCCD = 2.5 V to 3.3 V
and Tamb = −20 °C to +85 °C; unless otherwise specified. All RF input values are defined in potential difference, except when
EMF is explicitly stated.
Symbol
Parameter
Conditions
Min Typ Max Unit
Wideband AGC
Vi(RF)
RF input voltage
fRF = 93 MHz; fRF2 = 98 MHz;
66
72
78
dBµV
VRF2 = 50 dBµV; ∆Vth(mute) /
∆Vsens(EMF) < 4 mV/dBµV; radio tuned
to 98 MHz
IF filter
fcenter
B
center frequency
bandwidth
215 225 235 kHz
85
94
102 kHz
[1]
S
selectivity
ftune = 76 MHz to 108 MHz
high-side; ∆f = +200 kHz
low-side; ∆f = −200 kHz
high-side; ∆f = +100 kHz
low-side; ∆f = −100 kHz
ftune = 76 MHz to 108 MHz;
39
32
8
43
36
12
12
30
-
-
-
-
-
dB
dB
dB
dB
dB
8
IR
image rejection
24
VRF = 50 dBµV
FM IF level detector and mute voltage
VIF
IF voltage
VRF = 0 µV
1.5
1.6
1.55 1.6
1.61 1.7
V
V
VRF = 3 µV
VIF(slope)
VADC(start)
Gstep
slope of IF voltage level
ADC start voltage
∆Vlevel / ∆VRF; VRF = 10 µV to 500 µV
130 170 210 mV/20dB
2
2
3
3
5
5
µV
step resolution gain
dB
RTMUTE
pin TMUTE output resistance
280 400 520 kΩ
FM demodulator
Vo
output voltage
VRF = 1 mV; L = R; ∆f = 22.5 kHz;
55
70
75
mV
fmod = 1 kHz; DTC = 0; Baud = 300 Hz
to 15 kHz
Ro
output resistance
sink current
-
-
500
Ω
Isink
30
54
-
-
-
µA
dB
(S+N)/N
maximum signal-to-noise ratio fRF = 76 MHz to 108 MHz; VRF = 1 mV;
L = R; ∆f = 22.5 kHz; fmod = 1 kHz;
57
TCdeem= 75 µs; A-weighting filter;
Baud = 300 Hz to 15 kHz
THD
total harmonic distortion
V
RF = 1 mV; L = R; ∆f = 75 kHz;
-
0.4
0.9
1
%
fmod = 1 kHz; DTC = 0; A-weighting
filter; Baud = 300 Hz to 15 kHz;
see Figure 17
THDOD
total harmonic distortion
overdrive
VRF = 1 mV; L = R; ∆f = 100 kHz;
-
-
-
%
fmod = 1 kHz; DTC = 0; A-weighting
filter; Baud = 300 Hz to 15 kHz;
see Figure 17
AMsup
AM suppression
L = R; ∆f = 22.5 kHz; fmod = 1 kHz;
−40
-
dB
VRF = 100 µV to 10 mV; m = 0.3;
DTC = 0; Baud = 300 Hz to 15 kHz
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
49 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 47: FM signal channel characteristics …continued
See Figure 1; all AC values are given in RMS; the min. and max. values include spread due to VCCA = VCCD = 2.5 V to 3.3 V
and Tamb = −20 °C to +85 °C; unless otherwise specified. All RF input values are defined in potential difference, except when
EMF is explicitly stated.
Symbol
Parameter
Conditions
Min Typ Max Unit
Soft mute; SMUTE = 1; ∆f = 22.5 kHz; fmod = 1 kHz
Vstart(mute)
mute start voltage
mute attenuation
relative to VVAFL at VRF = 1 mV;
αmute = 3 dB
3
5
10
30
µV
αmute
VRF = 1 µV; L = R; DTC = 0;
10
20
dB
Baud = 300 Hz to 15 kHz
MPX decoder
VVAFL
left audio output voltage on pin VRF = 1 mV; L = R; ∆f = 22.5 kHz;
55
55
66
66
75
75
mV
mV
VAFL
fmod = 1 kHz; no pre-emphasis;
TCdeem = 75 µs
VVAFR
right audio output voltage on
pin VAFR
VRF = 1 mV; L = R; ∆f = 22.5 kHz;
fmod = 1 kHz; no pre-emphasis;
TCdeem = 75 µs
RVAFL
output resistance pin VAFL
RDSCDA = 0
MU = LHM = RHM = 0
MU = LHM = RHM = 1
RDSCDA = 0
50
-
-
100
-
Ω
500
kΩ
RVAFR
output resistance pin VAFR
MU = LHM = RHM = 0
MU = LHM = RHM = 1
50
-
-
-
-
-
100
-
Ω
500
200
200
4
kΩ
Isink(VAFL)
Isink(VAFR)
αODi
sink current on pin VAFL
sink current on pin VAFR
input overdrive range
300 µA
300 µA
THD = 3 % relative to fMPX = 1 kHz;
-
dB
V
MPX = 250 mV
VRF = 1 mV; L = R; ∆f = 75 kHz
between pins VAFL and VAFR including 9 % pilot deviation;
mod = 1 kHz
∆VO(VAFL-VAFR) output voltage difference
−0.5
-
-
+0.5 dB
f
αcs
channel separation
VRF = 1 mV; ∆f = 75 kHz including 9 %
pilot deviation; R = 1; L = 0 or R = 0;
L = 1; fmod = 1 kHz; MST = 0; SNC = 1;
27
-
dB
Baud = 300 Hz to 15 kHz
fu
fl
upper 3 dB bandwidth
lower 3 dB bandwidth
VRF = 1 mV; ∆f = 22.5 kHz;
pre-emphasis = 75 µs; DTC = 0; L = R;
with C between pin 27 and pin
26 = 33 nF ± 5 %
13
20
15
30
17
50
kHz
Hz
(S+N)/N(m)
(S+N)/N(s)
maximum signal-to-noise ratio, VRF = 1 mV; ∆f = 22.5 kHz; L = R;
mono mod = 1 kHz; de-emphasis = 75 µs;
AF = 300 Hz to 15 kHz; A-weighting
filter
54
50
57
54
-
-
dB
dB
f
B
maximum signal-to-noise ratio, VRF = 1 mV; ∆f = 67.5 kHz; L = R;
stereo mod = 1 kHz; ∆fpilot = 6.75 kHz;
f
de-emphasis = 75 µs; BAF = 300 Hz to
15 kHz; A-weighting filter
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
50 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 47: FM signal channel characteristics …continued
See Figure 1; all AC values are given in RMS; the min. and max. values include spread due to VCCA = VCCD = 2.5 V to 3.3 V
and Tamb = −20 °C to +85 °C; unless otherwise specified. All RF input values are defined in potential difference, except when
EMF is explicitly stated.
Symbol
Parameter
Conditions
Min Typ Max Unit
THD
total harmonic distortion
VRF = 1 mV; L = 1; R = 0; ∆f = 75 kHz
including 9 % pilot deviation;
fmod = 1 kHz; DTC = 0; Baud = 300 Hz
to 15 kHz; A-weighting filter
mono; L = R; no pilot deviation
-
-
0.4
0.9
0.9
2.5
%
%
stereo; L = 1, R = 0; 9 % pilot
deviation; see Figure 17
αsup(pilot)
pilot suppression
measured at pins VAFL and VAFR;
related to ∆f = 75 kHz including 9 %
pilot deviation; fmod = 1 kHz; DTC = 0
40
50
-
dB
∆fpilot
pilot frequency deviation
VRF = 1 mV
Table note [2]
αhys(pilot)
TCdeem
pilot tone detection hysteresis VRF = 1 mV
2
-
6
dB
de-emphasis time constant
VRF = 1 mV
DTC = 1
38
57
50
75
62
93
µs
µs
DTC = 0
Mono stereo blend; SNC = 1
[3]
Vstart(blend)
blend start voltage
channel separation
αcs = 0.5 dB
2
4
7
15
16
µV
αcs
VRF = 30 µV; ∆f = 75 kHz including 9 %
pilot deviation; R = 1 and L = 0 or R = 0
and L = 1; fmod = 1 kHz; MST = 0;
SNC = 1
10
dB
Mono stereo switching; ∆f = 75 kHz including 9 % pilot deviation; fmod = 1 kHz; SNC = 0
αcs
channel separation
MST = 0; R = 1 and L = 0 or R = 0 and
L = 1
VRF = 30 µV; increasing RF input
level
27
-
33
-
-
dB
dB
VRF = 10 µV; decreasing RF input
1
level
[4]
[4]
Vsw
hys
switching voltage
hysteresis
17
3
25
45
4
µV
3.5
dB
Bus driven mute functions
Tuning mute; AFM = 1
αmute(VAFR)
αmute(VAFL)
αmute
mute depth on pin VAFR
AFM = 1 or RHM = 1; ∆f = 75 kHz;
mono; Baud = 300 Hz to 15 kHz;
A-weighting filter
−60
−60
−80
-
-
-
-
-
-
dB
dB
dB
mute depth on pin VAFL
AFM = 1 or LHM = 1; ∆f = 75 kHz;
mono; Baud = 300 Hz to 15 kHz;
A-weighting filter
mute depth on pins VAFL and MU = 1; ∆f = 75 kHz; mono;
VAFR aud = 300 Hz to 15 kHz; A-weighting
filter
B
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
51 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
Table 47: FM signal channel characteristics …continued
See Figure 1; all AC values are given in RMS; the min. and max. values include spread due to VCCA = VCCD = 2.5 V to 3.3 V
and Tamb = −20 °C to +85 °C; unless otherwise specified. All RF input values are defined in potential difference, except when
EMF is explicitly stated.
Symbol
Parameter
Conditions
Min Typ Max Unit
RDS demodulator/decoder; ∆f = 22.5 kHz; fAF = 1 kHz; L = R; TCdeem = 50 µs; DTC = 1; SYM1 = 0 and SYM0 = 0;
average over 2000 blocks
IRDS
RDS current
ICCD current when RDS is running
0.3
0.7
1.5
mA
Vsens
RDS sensitivity EMF value
∆f = 22.5 kHz; fAF = 1 kHz; L = R;
SYM1 = 0 and SYM0 = 0
block quality rate ≥ 85 %;
∆fRDS = 1.2 kHz
-
-
24.7 37.5 µV
17 30 µV
57.5 kHz
block quality rate ≥ 95 %;
∆fRDS = 2 kHz
fcenter
filter center frequency
bandwidth
56.5 57
B
2.5
3
3.5
kHz
Pause detector
fth(det)(pause)
pause detection threshold
frequency
fmod = 1 kHz; L = R; PL0 = 0; PL1 = 0
0.7
1.0
1.4
kHz
[1] Low-side and high-side selectivity can be measured by changing the mixer LO injection from high-side to low-side.
[2] When bit STEREO is at logic 1 the frequency is between 2.5 kHz and 5.8 kHz; when bit STEREO is at logic 0 the frequency is 0 kHz.
[3] With increasing input levels the radio switches gradually from mono to stereo.
[4] The mono stereo switching level is the RF input level for switching from mono to stereo.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
52 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
001aac797
4.0
0
(1)
(2)
THD, N
(%)
(dB)
−20
−40
−60
−80
3.0
2.0
1.0
(3)
0
−7
−6
−5
−4
−3
−2
−1
10
10
10
10
10
10
10
1
V
(V)
RF
(1) Mono signal, soft mute off (fFM = 22.5 kHz; fAF = 1 kHz)
(2) Noise in mono mode, soft mute off
(3) Total harmonic distortion, ∆f = 75 kHz (fFM = 75 kHz; fAF = 1 kHz)
VCCA = 2.7 V; Tamb = 25 °C; AFout: A-weighting filter, BP filter: 300 Hz to 15 kHz
0 dB = 72 mV at 2 µV RF
−3 dB = 0.8 µV
26 dB = 1.4 µV.
RF = 98 MHz
Measurements/decade: 12
Fig 15. Mono characteristics
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
53 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
001aac798
4.0
0
(1)
(2)
THD, N
(%)
(dB)
−20
−40
−60
−80
3.0
2.0
1.0
(3)
(4)
0
−7
−6
−5
−4
−3
−2
−1
10
10
10
10
10
10
10
1
V
(V)
RF
(1) VAFL signal, soft mute off (∆fR = 67.5 kHz; fAF = 1 kHz; ∆fpilot = 6.75 kHz)
(2) VAFR signal, soft mute off (∆fL = 67.5 kHz; fAF = 1 kHz; ∆fpilot = 6.75 kHz)
(3) Noise in stereo mode, soft mute off (∆fL = 0 kHz; fAF = 1 kHz; ∆fpilot = 6.75 kHz)
(4) Total harmonic distortion, ∆f = 75 kHz (∆fR = 67.5 kHz; fAF = 1 kHz; ∆fpilot = 6.75 kHz)
VCCA = 2.7 V; Tamb = 25 °C; AFout: A-weighting filter, BP filter: 300 Hz to 15 kHz; SNC = on
0 dB = 233 mV at 470 µV RF
26 dB = 1.3 µV
RF = 98 MHz
Measurements/decade: 12
Fig 16. Stereo characteristics
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
54 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
001aac799
4.0
0
(1)
THD, N
(%)
(dB)
−20
−40
−60
−80
3.0
2.0
1.0
(2)
(3)
0
−7
−6
−5
−4
−3
−2
−1
10
10
10
10
10
10
10
1
V
(V)
RF
(1) Mono signal, soft mute on (fFM = 22.5 kHz; fAF = 1 kHz)
(2) Noise in mono mode, soft mute on
(3) Total harmonic distortion, ∆f = 100 kHz (fFM = 100 kHz; fAF = 1 kHz)
VCCA = 2.7 V; Tamb = 25 °C; AFout: A-weighting filter, BP filter: 300 Hz to 15 kHz; soft mute on
0 dB = 71 mV at 10 µV RF
26 dB = 1.4 µV
RF = 98 MHz
Measurements/decade: 12
Fig 17. Soft mute and overdrive characteristics
001aac800
−3
10
V
,
RFIN1
V
RFIN2
(V)
−4
10
−5
−6
−7
10
10
10
0
4
8
12
16
ADC output
Fig 18. ADC conversion levels
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
55 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
15. Application information
Table 48: List of components
Symbol
D1, D2
L1
Parameter
Type
Manufacturer
varicap diode for VCO tuning BB202
Philips
RF band filter coil
VCO coil
120 nH; Qmin = 20; tolerance: ±5 %
33 nH; Qmin = 40; tolerance: ±2 %
Coilcraft; Murata
Coilcraft; Murata
L2, L3
X1
32.768 kHz crystal
ACT200; CL = 12 pF; ∆f / f0 = ±20 ppm; ACT
see Section 14
R
C
10 kΩ; 47 kΩ; 100 kΩ
±10 % max
27 pF; 47 pF; 100 pF; 12 pF; ±10 % max
10 nF(2×); 33 nF(8×)
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
56 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
16. Package outline
WLB34: wafer-level ball grid array; 34 balls; 4 x 4 x 0.36 mm
TEA5764UK
D
B
A
ball A1
index area
A
2
A
E
A
1
detail X
C
e
1
y
M
M
v
C
C
A
B
b
e
w
G
F
e
E
D
C
B
A
e
2
1
2
3
4
5
6
7
X
0
1
2
3 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
A
1
A
2
b
D
E
e
e
e
2
v
w
y
1
max
0.26 0.38 0.38 4.02 4.02
0.22 0.34 0.28 3.96 3.96
mm
0.6
0.5
3
3
0.05
0.1 0.015
REFERENCES
JEDEC JEITA
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
05-04-21
05-06-23
TEA5764UK
Fig 19. Package outline TEA5764UK (WLB34)
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
57 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
17. Soldering
17.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
17.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 seconds and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 °C to 270 °C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
• below 225 °C (SnPb process) or below 245 °C (Pb-free process)
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness ≥ 2.5 mm
– for packages with a thickness < 2.5 mm and a volume ≥ 350 mm3 so called
thick/large packages.
• below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
17.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
• Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
• For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
parallel to the transport direction of the printed-circuit board;
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
58 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
• For packages with leads on four sides, the footprint must be placed at a 45° angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 °C
or 265 °C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
17.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300 °C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270 °C and 320 °C.
17.5 Package related soldering information
Table 49: Suitability of surface mount IC packages for wave and reflow soldering methods
Package [1]
Soldering method
Wave
Reflow[2]
BGA, HTSSON..T[3], LBGA, LFBGA, SQFP,
SSOP..T[3], TFBGA, VFBGA, XSON
not suitable
suitable
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
not suitable[4]
suitable
PLCC[5], SO, SOJ
suitable
suitable
LQFP, QFP, TQFP
not recommended[5] [6]
not recommended[7]
not suitable
suitable
SSOP, TSSOP, VSO, VSSOP
CWQCCN..L[8], PMFP[9], WQCCN..L[8]
suitable
not suitable
[1] For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026);
order a copy from your Philips Semiconductors sales office.
[2] All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal or
external package cracks may occur due to vaporization of the moisture in them (the so called popcorn
effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit
Packages; Section: Packing Methods.
[3] These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no
account be processed through more than one soldering cycle or subjected to infrared reflow soldering with
peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package
body peak temperature must be kept as low as possible.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
59 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
[4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the
solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink
on the top side, the solder might be deposited on the heatsink surface.
[5] If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
[6] Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is
definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
[7] Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger
than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
[8] Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered
pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex foil by
using a hot bar soldering process. The appropriate soldering profile can be provided on request.
[9] Hot bar soldering or manual soldering is suitable for PMFP packages.
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
60 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
18. Revision history
Table 50: Revision history
Document ID
TEA5764UK_2
Modifications:
TEA5764UK_1
Release date Data sheet status
20050809 Product data sheet
Change notice Doc. number
Supersedes
-
-
TEA5764UK_1
• Specification status changed from preliminary data sheet to product data sheet.
20050701
Preliminary data sheet
-
-
-
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
61 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
19. Data sheet status
Level Data sheet status[1] Product status[2] [3]
Definition
I
Objective data
Development
This data sheet contains data from the objective specification for product development. Philips
Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data
Qualification
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data
Production
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
[1]
[2]
Please consult the most recently issued data sheet before initiating or completing a design.
The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at
URL http://www.semiconductors.philips.com.
[3]
For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
customers using or selling these products for use in such applications do so
at their own risk and agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
20. Definitions
Short-form specification — The data in a short-form specification is
extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Right to make changes — Philips Semiconductors reserves the right to
make changes in the products - including circuits, standard cells, and/or
software - described or contained herein in order to improve design and/or
performance. When the product is in full production (status ‘Production’),
relevant changes will be communicated via a Customer Product/Process
Change Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no
license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are
free from patent, copyright, or mask work right infringement, unless otherwise
specified.
Limiting values definition — Limiting values given are in accordance with
the Absolute Maximum Rating System (IEC 60134). Stress above one or
more of the limiting values may cause permanent damage to the device.
These are stress ratings only and operation of the device at these or at any
other conditions above those given in the Characteristics sections of the
specification is not implied. Exposure to limiting values for extended periods
may affect device reliability.
Application information — Applications that are described herein for any
of these products are for illustrative purposes only. Philips Semiconductors
make no representation or warranty that such applications will be suitable for
the specified use without further testing or modification.
22. Trademarks
Notice — All referenced brands, product names, service names and
trademarks are the property of their respective owners.
I2C-bus — wordmark and logo are trademarks of Koninklijke Philips
Electronics N.V.
21. Disclaimers
Life support — These products are not designed for use in life support
appliances, devices, or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors
23. Contact information
For additional information, please visit: http://www.semiconductors.philips.com
For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
62 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
24. Contents
1
2
3
4
5
6
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Quick reference data . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
9
9.1
Interrupt handling . . . . . . . . . . . . . . . . . . . . . . 16
Interrupt register. . . . . . . . . . . . . . . . . . . . . . . 16
Interrupt clearing . . . . . . . . . . . . . . . . . . . . . . 17
Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Interrupt flags and behavior . . . . . . . . . . . . . . 19
Multiple interrupt events . . . . . . . . . . . . . . . . . 19
Data available flag . . . . . . . . . . . . . . . . . . . . . 19
RDS synchronization flag. . . . . . . . . . . . . . . . 19
IF frequency flag . . . . . . . . . . . . . . . . . . . . . . 20
RSSI threshold flag . . . . . . . . . . . . . . . . . . . . 20
Pause detection flag. . . . . . . . . . . . . . . . . . . . 21
Frequency ready flag . . . . . . . . . . . . . . . . . . . 22
Band limit flag. . . . . . . . . . . . . . . . . . . . . . . . . 23
Interrupt output. . . . . . . . . . . . . . . . . . . . . . . . 23
9.1.1
9.1.2
9.1.3
9.1.4
9.1.4.1
9.1.4.2
9.1.4.3
9.1.4.4
9.1.4.5
9.1.4.6
9.1.4.7
9.1.4.8
9.2
7
7.1
7.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 5
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
8
Functional description . . . . . . . . . . . . . . . . . . . 6
Low noise RF amplifier . . . . . . . . . . . . . . . . . . 6
FM I/Q mixer. . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . . . 6
PLL tuning system . . . . . . . . . . . . . . . . . . . . . . 7
Band limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
RF AGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Local or long distance receive . . . . . . . . . . . . . 8
IF filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FM demodulator . . . . . . . . . . . . . . . . . . . . . . . . 8
IF counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Voltage level generator and analog-to-digital
converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Soft mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hard mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Audio frequency mute. . . . . . . . . . . . . . . . . . . . 9
MPX decoder . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Signal dependent mono/stereo blend (stereo
noise cancellation) . . . . . . . . . . . . . . . . . . . . . . 9
Software programmable port . . . . . . . . . . . . . 10
Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . 10
Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 10
RDS/RBDS . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RDS/RBDS demodulator . . . . . . . . . . . . . . . . 10
RDS data and clock direct . . . . . . . . . . . . . . . 10
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
10
10.1
10.2
RDS data processing . . . . . . . . . . . . . . . . . . . 23
DAV-A processing mode. . . . . . . . . . . . . . . . . 24
DAV-B processing mode / fast PI search
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DAV-C reduced processing mode . . . . . . . . . 26
Synchronization . . . . . . . . . . . . . . . . . . . . . . . 28
Conditions for synchronization . . . . . . . . . . . . 28
Data overflow . . . . . . . . . . . . . . . . . . . . . . . . . 29
RDS flag behavior during read action . . . . . . 30
Error detection and reporting . . . . . . . . . . . . . 31
RDS test modes. . . . . . . . . . . . . . . . . . . . . . . 31
Reading RDS data from the registers . . . . . . 31
I2C-bus interface . . . . . . . . . . . . . . . . . . . . . . . 31
Write and read mode . . . . . . . . . . . . . . . . . . . 31
Data transfer. . . . . . . . . . . . . . . . . . . . . . . . . . 32
Register map . . . . . . . . . . . . . . . . . . . . . . . . . 34
Byte description . . . . . . . . . . . . . . . . . . . . . . . 34
10.3
10.4
10.4.1
10.4.2
10.5
10.6
10.7
10.8
8.13
8.13.1
8.13.2
8.13.3
8.14
11
11.1
11.2
11.3
11.4
8.15
8.16
8.17
8.18
8.19
8.19.1
8.19.2
12
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 45
Static characteristics . . . . . . . . . . . . . . . . . . . 46
Dynamic characteristics. . . . . . . . . . . . . . . . . 47
Application information . . . . . . . . . . . . . . . . . 56
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 57
13
14
15
8.19.2.1 RDS/RBDS decoder . . . . . . . . . . . . . . . . . . . . 11
16
8.20
8.21
8.21.1
8.21.2
8.21.3
Audio pause detector . . . . . . . . . . . . . . . . . . . 11
Auto search and Preset mode . . . . . . . . . . . . 11
Search mode . . . . . . . . . . . . . . . . . . . . . . . . . 13
Preset mode . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Auto high-side and low-side injection
stop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Muting during search or preset. . . . . . . . . . . . 14
RDS update/alternative frequency jump. . . . . 14
Muting during RDS update . . . . . . . . . . . . . . . 15
17
17.1
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Introduction to soldering surface
mount packages. . . . . . . . . . . . . . . . . . . . . . . 58
Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . 58
Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 58
Manual soldering . . . . . . . . . . . . . . . . . . . . . . 59
Package related soldering information. . . . . . 59
17.2
17.3
17.4
17.5
8.21.4
8.22
8.22.1
18
19
Revision history . . . . . . . . . . . . . . . . . . . . . . . 61
Data sheet status. . . . . . . . . . . . . . . . . . . . . . . 62
continued >>
TEA5764UK_2
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 9 August 2005
63 of 64
TEA5764UK
Philips Semiconductors
FM radio + RDS
20
21
22
23
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Contact information . . . . . . . . . . . . . . . . . . . . 62
© Koninklijke Philips Electronics N.V. 2005
All rights are reserved. Reproduction in whole or in part is prohibited without the prior
written consent of the copyright owner. The information presented in this document does
not form part of any quotation or contract, is believed to be accurate and reliable and may
be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under
patent- or other industrial or intellectual property rights.
Date of release: 9 August 2005
Document number: TEA5764UK_2
Published in The Netherlands
相关型号:
TEA5766UK
IC FM, AUDIO SINGLE CHIP RECEIVER, PBGA25, 3.30 X 3.25 MM, 0.60 MM HEIGHT, WLCSP-25, Receiver IC
NXP
TEA5767HN/V3,118
IC FM, AUDIO SINGLE CHIP RECEIVER, PQCC40, 6 X 6 MM, 0.85 MM HEIGHT, PLASTIC, MO-220, SOT-618-1, HVQFN-40, Receiver IC
NXP
TEA5768HL/V2,157
IC FM, AUDIO SINGLE CHIP RECEIVER, PQFP32, 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-358-1, LQFP-32, Receiver IC
NXP
TEA5777HL/N2,118
IC AM/FM, AUDIO SINGLE CHIP RECEIVER, PQFP32, 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-358-1, LQFP-32, Receiver IC
NXP
©2020 ICPDF网 联系我们和版权申明