D6F-P0010AM2 [OMRON]

MEMS Mass Flow Sensor; MEMS质量流量传感器


型号：	D6F-P0010AM2
厂家：	OMRON ELECTRONICS LLC
描述：	MEMS Mass Flow Sensor MEMS质量流量传感器传感器
文件：	总6页 (文件大小：688K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MEMS Mass Flow Sensor

D6F-P

A Compact, High-performance Flow

Sensor with Dust Segregation Structure.

• Built in Dust Segregation System (DSS) with cyclone flow

structure, diverts particulates from sensor element.

• High resolution and repeatability, even at low flow rates.

• Barbed ports with connector or PCB terminals, or manifold

mount with connector versions.

• Built in voltage regulator, temperature compensation and

amplified output. Measure up to 200 LPM with a bypass setup.

• Alternative to differential pressure sensing.

• RoHS Compliant

Ordering Information

Description

Case

Calibration Gas Flow Range

(See note 1.)

Mounting

Method

Connection

Model

Flow Sensor

PBT

Air (See note 2.)

0-0.1 LPM

0-1 LPM

Flange mount

PCB terminals D6F-P0001A1

D6F-P0010A1

Connector

Manifold mount Connector

- - - - - -

D6F-P0010A2

D6F-P0010AM2

D6F-CABLE2

Cable Connector Assembly

- - -

Note: 1. Can be calibrated for different gas types. Consult your Omron representative.

2. Dry gas must not contain large particles, eg dust, oil, mist.

3. Cable Assembly “D6F-CABLE2”, used with D6F-P0010A2 and D6F-P0010AM2, is sold separately.

Specifications

■ Characteristics

Models

D6F-P0001A1

0 to 0.1 L/min.

Air

barbed fitting maximum outside dia. 4.9 mm

Lead terminal

D6F-P0010A1

0 to 1 L/min.

D6F-P0010A2

D6F-P0010AM2

Flow Range (See note 1.)

Calibration Gas (See note 2.)

Flow Port Type

manifold mount

Electrical Connection

Connector (3 wire)

Power Supply

4.75 to 9.45 VDC

Current Consumption

Operating Output Voltage

Output Voltage Limits (Min and Max.)

Accuracy and Temperature Characteristics

Repeatability (Reference (typical))

Case Material

Max. 15 mA (no load, Vcc = 5 VDC)

0.5 to 2.5 VDC

0 VDC min. and 3.1 VDC max. (Lead resistance 10 kΩ)

5% F.S. max. of detected characteristics at 25 C, within -10 to 60 °C (typical test results within ±2% F.S.)

± 1.0% F.S.

PBT

± 0.4% F.S.

Degree of Protection

IP40

Withstand Pressure

Pressure Drop (Reference (typical))

Operating Temperature

50 kPa (7 psi)

0.19 kPa

0.48 kPa

-10 to 60°C (1 LPM versions) and -33 to 75°C (0.1 LPM version) with no icing or condensation

(Storage: -40 to 80°C with no icing or condensation)

Operating Humidity

Insulation Resistance

Dielectric Strength

35 to 85% RH with no icing or condensation (Storage: 35 to 85% RH with no icing or condensation)

20 MΩ (500 VDC between lead terminal and the case)

500 VAC, 50/60 Hz for 1 minute. (Leakage current typ. Max. 1mA) between lead terminals and case.

Weight

8.5 g

8.0 g

Response Time (Reference (typical))

150 msec

Note: 1. Mass flow converted into volumetric flow rate, SLM (standard liters per minute) at 0°C, 1 atmosphere.

2. Dry gas. (must not contain large particles, dust, oil, mist)

MEMS Mass Flow Sensor D6F-P

■ Absolute Maximum Rating

Item

Power supply voltage

Output voltage

Symbol

Rating

Unit

VDC

Vcc

Vout

4.0

■ Output Voltage Characteristics

D6F-P0001A@

D6F-P0010A@

3.0

2.5

2.0

1.5

1.0

0.5

0.0

3.0

2.5

2.0

1.5

1.0

0.5

0.0

0.02

0.04

0.06

0.08

0.10

0.25

0.5

0.75

Flow Rate (L/min)

D6F-P0001A@

Flow Rate (LPM)

0.00

0.02

0.04

0.06

1.70 ± 0.10

0.08

2.10 ± 0.10

0.10

Output Voltage (VDC)

0.50 ± 0.10

0.90 ± 0.10

1.30 ± 0.10

2.50 ± 0.10

D6F-P0010A@

Flow Rate (LPM)

0.00

0.25

1.60 ± 0.10

0.50

2.10 ± 0.10

0.75

2.31 ± 0.10

1.00

Output Voltage (VDC)

0.50 ± 0.10

2.50 ± 0.10

Note: 1. Mass flow converted into volumetric flow rate, SLM (standard liters per minute) at 0°C, 1 atmosphere.

2. 0 to 0.5 VDC output indicates a negative flow direction.

3. Measurement condition: Power supply voltage 5 ± 0.1VDC, ambient temperature 25 ± 5 °C and ambient humidity 25 to 75% RH.

■ Repeatability. (Typical test results)

(5 Samples, D6F-P0010A@, repeated 10 times each)

1.0

0.8

0.6

0.4

0.2

0.0

-0.2

-0.4

-0.6

-0.8

-1.0

0.0

0.3

0.5

0.8

1.0

Flow Rate(lpm)

MEMS Mass Flow Sensor D6F-P

Dimensions

Note: All units are in millimeters unless otherwise indicated.

PCB terminals with Flange Mount

D6F-P0001A1 / D6F-P0010A1

Label: Gives model and lot numbers.

23.3

11.7

7.3

2.6 dia.

Two, 4.9 dia.

Two, 1.1 dia.

Two 3-dia.

through holes

XG8V-0344

13.5

4.76

2.54

Connector

0.2

7.6

Label

27.2

Three lands,

Dia.: 1.3

Made by OMRON

16.2

7.2

GND

Vcc

Three through holes

Dia.: 0.8

2.54

1.7

1.2

17.2

9.8

5.08

Vout

5.08

Detailed View of A

Recommended Dimensions

for Connector Mounting Holes

13.5

1.5

Two, R1.4

2.8 dia.

7.2

13.2

4.76

Connector with Flange Mount

D6F-P0010A2

7.3

Label: Gives model

and lot numbers.

11.7

Two, 4.9 dia.

Two, 1.1 dia.

23.3

2.6 dia.

Label

0.2

7.6

27.2

8.5

16.2

Note: 1. Use M3 or M2.6 pan screw or tapping screw

with an equal diameter for installation. And

bind tight with 0.59N·m or less torque.

1.2

8.5

1.7

13.5

1.5

17.2

3.Vcc

2.Vout

1.GND

2.8 dia.

Two, R: 1.4

13.2

2. Use an attached connector. Manufactured

by JST Mfg Co., Ltd. (Japan) for A2 and

AM2 types.

• Pressure welding connector

Socket: 03SR-3S

Detailed View of A

Wire: AWG#30

Connector with Manifold Mount

• Crimp type connector

Contact: SSH-003T-P0.2|

Wire: AWG#32 to #28

• Housing: SHR-03V-S

D6F-P0010AM2

6.7

0.1

Two, 4^-0.05dia.

3. O-rings are not attached. 4mm ID tube

recommended for D6F-P0010A1 and

D6F-P0010A2 types.

3.5 dia.

1^+0.1

27.2

0.05

6.4 9.6

2-C0.3

1. GND

0.1

2.7

2. Vout

3. Vcc

0.1

0.3

0.1

0.3

Detailed View of A

Label

Detailed View of B

Antirotain groove

Connector

Applicable Cable for D6F-P0010A@2 (Optional - sold separately)

part number: D6F-CABLE2

White wire

Black wire

1. GND

2. Vout

Red wire

3. Vcc

15 3

180 10

(5)

MEMS Mass Flow Sensor D6F-P

Packaging

TYPE D6F-P

No.

Item

Sock liner

Tray (25pcs)

Box (100 pcs)

Material

CCNB

Polyethylene

CCNB

Display seal

Application Information and Examples

■ Bidirectional Dust Segregation System

The D6F-P series has a patented dust segregation design. The flow path incorporates dual centrifugal chambers, in which particulate matter follows

in the outer path, away from the MEMS sensor chip regardless of the flow direction. Note, standard products are calibrated for unidirectional flow,

as indicated in note 3 of the “Output Characteristics” table, above. Contact Omron for bidirectional calibration options.

sensing element

Bypass Setup

HVAC Application

When used in a bypass set-up, as illustrated below, the D6F-P mass

flow sensors can measure flow rates far beyond the 1 LPM in-line rat-

ing. The pressure differential required to pull airflow through the sen-

sor can be accomplished by installing a flow restrictor between the

two ports or through the use of a flow cross in large ducts, as shown

in the HVAC application.

The D6F-P mass flow sensor is ideal for damper control in variable

air volume systems, where low flow rates are difficult to measure with

differential pressure sensors.

Note: Be sure to read the precautions and information common to all D6F sensors, contained in the Technical User’s Guide, “D6F Technical Information”

for correct use.

MEMS Mass Flow Sensor D6F-P

MEMO

MEMS Mass Flow Sensor D6F-P

All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which

can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.components.omron.com

OMRON ELECTRONIC

COMPONENTS LLC

55 E. Commerce Drive, Suite B

Schaumburg, IL 60173

847-882-2288

10/10

Specifications subject to change without notice

Printed in USA

Cat. No. X305-E-1

MEMS Mass Flow Sensor D6F-P

相关型号：