E3S-CL22M [OMRON]
Distance-settable Photoelectric Sensor with Metal Case;型号: | E3S-CL22M |
厂家: | OMRON ELECTRONICS LLC |
描述: | Distance-settable Photoelectric Sensor with Metal Case |
文件: | 总10页 (文件大小:677K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Distance-settable Photoelectric Sensor with Metal Case
E3S-CL
CSM_E3S-CL_DS_E_4_2
Simply Set the Distance to Reliably
Detect Workpieces of Various Colors
• Reliable detection regardless of color or material.
Black/white error of only 2% max. (E3S-CL1)
• Long sensing distance of 500 mm (E3S-CL2).
• Eliminates background influence.
(Differential travel of only 2% max. with E3S-CL1.)
• Metal body with IP67 protection.
Oil resistance (E3S-CL2).
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read Safety Precautions on
page 7.
Ordering Information
Sensors (Refer to Dimensions on page 8.)
Red light
Model
Infrared light
Appearance
Sensing/Setting range
5
5
40 mm
Setting range
40 to 200 mm
Min. setting
Max. setting
E3S-CL1 2M
200 mm
Sensing range
5 to 200 mm
5
5
50 mm
Setting range
50 to 500 mm
Min. setting
Max. setting
E3S-CL2 2M
Sensing range
5 to 500 mm
500 mm
1
E3S-CL
Ratings and Specifications
Sensing method
Distance-settable
Item
Model
E3S-CL1
E3S-CL2
5 to 200 mm (white paper: 200 x 200 mm,
setting distance: 200 mm)
5 to 500 mm (white paper: 200 x 200 mm,
setting distance: 500 mm)
Sensing distance
Setting range
40 to 200 mm (white paper: 200 x 200 mm)
2% max. of setting distance
50 to 500 mm (white paper: 200 x 200 mm)
10% max. of setting distance
Differential travel
Reflectivity characteris-
tics (black/white error) *1
2% max. of setting distance
10% max. of setting distance
Infrared LED (860 nm)
Light source (wavelength) Red LED (700 nm)
Power supply voltage
Current consumption
10 to 30 VDC; ripple: 10% max.
35 mA max.
50 mA max.
Load power supply voltage: 30 VDC max., Load current: 100 mA max.
Residual voltage: NPN output: 1.2 V max.
PNP output: 2 V max.
Control output
Open collector output (NPN/PNP depending on model)
Light-ON/Dark-ON selectable
Protection circuits
Response time
Power supply reverse polarity protection, Output short-circuit protection, Mutual interference prevention
Operate or reset: 1 ms max.
Operate or reset: 2 ms max.
Distance setting
Six-turn endless adjustor with an indicator
Ambient illumination
(Receiver side)
Incandescent lamp: illumination on optical spot: 5,000 lx max.
Sunlight: illumination on optical spot: 10,000 lx max.
Ambient temperature
range
Operating/storage: −25 to 55°C (with no icing or condensation)
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Operating/storage: 35% to 85% (with no condensation)
20 MΩ min. at 500 VDC
1,000 VAC, 50/60 Hz for 1 min
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hrs each in X, Y, and Z directions
Destruction: 500 m/s2 3 times each in X, Y, and Z directions
IP67 (IEC 60529) (in-house standards: oil-resistant),
NEMA: 6P (indoors only) *2
Degree of protection
IP67 (IEC 60529), NEMA: 6P (indoors only) *2
Connection method
Weight (packed state)
Case
Pre-wired (standard length: 2 m)
Approx. 170 g
Zinc die-cast
Ma-
teri-
als
Operation panel
Lens
PES (Polyether sulfone)
Methacrylic resin
Mounting bracket
Stainless steel (SUS304)
Mounting bracket, 12 M4 hexagonal bolts (with spring and flat washers), Adjustment screwdriver, and Instruction
manual
Accessories
*1. Sensing distance error for standard white (90% reflective) and black (5% reflective) paper.
*2. NEMA: National Electrical Manufacturers Association
2
E3S-CL
Engineering Data (Reference value)
Operating Range
E3S-CL1
E3S-CL2
30
20
Distance setting: 300, 500 mm
Standard sensing object
White paper, 200 x 200 mm
Distance setting: 40, 100, and 200 mm
Standard sensing object
White paper, 200 x 200 mm
15
20
10
10
5
200 mm
500 mm
300 mm
200
40 mm 100 mm
0
0
−5
100
300
400
500
50
100
150
200 250
Distance
X (mm)
−10
−20
−30
Distance
X (mm)
−10
−15
−20
Y
Y
X
X
Sensing Object Size vs. Sensing Distance
E3S-CL1
E3S-CL2
300
600
White paper
Black paper
White paper
Black paper
Setting
distance
500 mm
250
200
150
100
50
500
Setting
distance
200 mm
400
300
200
100
300 mm
100 mm
40 mm
50 mm
0
10
20
30
40
50
0
10
20
30
40
50
Size of object (mm)
Size of object (mm)
Spot Diameter vs. Sensing Distance
E3S-CL1
E3S-CL2
25
100
20
15
10
5
80
60
40
20
0
50
100
150
200
250
0
100
200
300
400
500
Distance (mm)
Distance (mm)
3
E3S-CL
Sensing Distance vs. Minimum Detectable Object Size
E3S-CL1
E3S-CL2
2.5
3.0
Sensing object: Stainless steel bar
Distance setting: Max.
Sensing object: Stainless steel bar
Distance setting: Max.
2.5
2.0
1.5
1.0
0.5
2.0
1.5
1.0
0.5
0
50
100
150
200
250
0
100
200
300
400
500
600
Distance (mm)
Distance (mm)
Sensing Object Angle Characteristics
E3S-CL1 Vertical
E3S-CL1 Horizontal
3
3
Sensing object: White paper, 200 x 200 mm
Sensing distance: 200 mm
Sensing object: White paper, 200 x 200 mm
Sensing distance: 200 mm
2
1
0
2
1
0
Horizontal
Detection
−1
Vertical
Detection
−1
Angle
+θ
−θ
Angle
+θ
−θ
−2
−3
−2
−3
Detected
object
Detected
object
10
−40 −30 −20 −10
0
10
20
30
40
−40 −30 −20 −10
0
20
30
40
Angle θ (°)
Angle θ (°)
E3S-CL2 Vertical
E3S-CL2 Horizontal
6
3
Sensing object: White paper,
200 x 200 mm
Sensing distance: 200 mm
Sensing object: White paper, 200 x 200 mm
Sensing distance: 200 mm
Horizontal
Detection
4
2
2
Angle
1
+θ
−θ
Detected
object
0
0
Vertical
Detection
−2
−1
Angle
+θ
−θ
−4
−6
−2
−3
Detected
object
−40 −30 −20 −10
0
10
20
30
40
−40 −30 −20 −10
0
10
20
30
40
Angle θ (°)
Angle θ (°)
4
E3S-CL
Sensing Distance vs. Sensing Object Material
E3S-CL1
(Setting Distance of 200 mm using White
Paper)
(Setting Distance of 100 mm using White
Paper)
(Setting Distance of 40 mm using White Paper)
200
150
100
50
40
30
20
10
100
75
50
25
0
0
0
Material
Material
Material
E3S-CL2
(Setting Distance of 500 mm using White
Paper)
(Setting Distance of 300 mm using White
Paper)
(Setting Distance of 50 mm using White Paper)
500
400
300
200
100
0
300
200
100
0
50
40
30
20
10
0
Material
Material
Material
Close-range Characteristics
E3S-CL1
E3S-CL2
Distance
setting
max.
Distance
setting
min.
Distance
setting
max.
500
200
150
100
50
Distance
setting
min.
400
300
200
100
33.7 mm
32.7 mm
11.4 mm
36 mm
33 mm
23.7 mm
2.7 mm
1.4 mm
0.7 mm
0
0.4 mm 6.2 mm
2.6 mm
0
White paper
Black paper
Black paper
Material
White paper
Material
5
E3S-CL
I/O Circuit Diagrams
NPN Output
Operation
Operation
selector
Model
mode
Timing charts
Output circuit
Incident light
No incident light
Operation
indicator
(orange)
Output
ON
OFF
ON
L side
(LIGHT ON)
10 to 30 VDC
Brown
Black
Blue
Stability
indicator
(green)
Light-ON
PNP output
ZD
transistor
OFF
transistor
Load Load current
Control output
Photo-
Operate
Reset
Load
(relay)
Light
indicator
(orange)
electric
Sensor
Main
NPN and PNP
output selector
E3S-CL1
E3S-CL2
Circuit
*
Incident light
NPN output
ZD
No incident light
transistor
0 V
Operation
indicator
(orange)
Output
ON
OFF
ON
D side
(DARK ON)
Dark-ON
*Set the NPN and PNP output selector to NPN.
transistor
OFF
Operate
Reset
Load
(relay)
PNP Output
Operation
Operation
selector
Model
mode
Timing charts
Output circuit
Incident light
No incident light
Operation
indicator
(orange)
Output
ON
OFF
ON
L side
(LIGHT ON)
Brown
10 to 30 VDC
Control output
Light-ON
Stability
indicator
(green)
PNP output
transistor
transistor
ZD
ZD
OFF
Operate
Reset
Photo-
Load
(relay)
Light
indicator
(orange)
*
electric
Sensor
Main
Black
Blue
NPN and PNP
output selector
E3S-CL1
E3S-CL2
Circuit
Load Load current
0 V
Incident light
NPN output
transistor
No incident light
Operation
indicator
(orange)
Output
ON
OFF
ON
D side
(DARK ON)
*Set the NPN and PNP output selector to PNP.
Dark-ON
transistor
OFF
Operate
Reset
Load
(relay)
Nomenclature
Operation Panel
Output Selector
Cover
1. Set the selector to NPN for NPN output.
2. Set the selector to PNP for PNP output.
Operation Selector
1. Set the selector to L-ON for ON light-ON operation.
2. Set the selector to D-ON for ON dark-ON operation.
Stability indicator
(green)
Light indicator
(orange)
Setting Distance Adjuster
1. The sensing distance will increase when the adjuster is turned
clockwise (toward Max.) and will decrease when the knob is turn
counterclockwise.
2. The adjustment can be turned up to 6 times clockwise or
counterclockwise to set the sensing distance. The number of turns
will be displayed by the indicator.
Output
selector
Setting distance
indicator
Operation
selector
Setting distance
adjuster
6
E3S-CL
Safety Precautions
Refer to Warranty and Limitations of Liability.
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
• Also, mount the Sensor so that it is not aligned with extreme
changes in color or materials, as shown below.
Precautions for Correct Use
Do not use the product in atmospheres or environments that exceed
product ratings.
● Designing
Cable
Direction of
movement
The E3S-CL2 uses an oil-resistive cord to ensure oil resistivity.
Direction of
movement
● Mounting
• Mount the Sensor so that sunlight, fluorescent light, incandescent
light, or other strong sources of light do not enter the directional
angle of the Sensor.
Mounting
Mounting Direction
• Mount the Sensor so that the sensing
face runs parallel to the surface of the
object being detected as shown
below, and not at an angle.
Precautions
• When mounting the Sensor, do not hit the Sensor with a hammer,
or the Sensor will lose its watertightness.
• Use M4 screws to mount the Sensor.
• The tightening torque of each screw must be 1.2 N·m maximum.
Sensing side
● Others
Surface of
sensing object
Oil and Chemical Resistivity (E3S-CL2)
The E3S-CL2 was tested for resistance to the oils given in the
following table. Refer to the information in the table when deciding
which type of oil to use. However, performance may be affected by
certain types of oil.
If detecting a shiny object, however,
mount the Sensor so that the sensing
face is at an angle of between 5° and
10° of the surface of the object being
detected as shown below, and check
to be sure that there is no
Test oil
classification
Kinematic viscosity
Product name
Velocity No.3
pH
(mm2/s (cst)) at 40°C
Lubricating oil
2.02
interference from the background.
---
Water insoluble
machining oil
Yushiron Oil No. 2 ac
Less than 10
Shiny object
• If stable operation is not possible near
a mirror surface, mount the Sensor at
an angle as shown below, and separate the Sensor as far as
possible from the mirror surface.
Yushiroken EC50T-3
Yushiron Lubic HWC68
Gryton 1700D
7 to 9.5
7 to 9.9
7 to 9.2
7 to 9.8
Water soluble
machining oil
---
Yushiroken S50N
Note: 1. The E3S-CL2 maintained a minimum insulation resistance of 100 MΩ
after it was dipped in all the above oils at a temperature of 50°C for 240
hours.
Sensing
object
2. When using the E3S-CL2 in environments subject to oils other than
those listed above, use the figures for kinematic viscosity and ph
values from the table as general guidelines. Additives and other
substances contained in oils may affect the E3S-CL2. Be sure to
consider this before use.
Mirror surface
• Mount the Sensor so that it is not aligned with the direction of
movement of the sensing object, as shown below.
Sensing
Sensing
object
Sensing
object
object
Direction of
movement
Direction of
movement
Direction of
movement
7
E3S-CL
(Unit: mm)
Dimensions
Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.
E3S-CL1
E3S-CL2
23.8
7.3
With Mounting Bracket Attached
11.7
Stainless steel
6.2
4.2
9.2
4.2
20
12
Mounting Holes
19.7
Two, M4
Light indicator
Stability indicator
25.4
40
Receiver
Two, M4 hex bolts
with slit lock washers
1.1
15.4
37.2
Two, M4
E3S-CL1:
16
28
42.6
4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.2 mm2 (AWG24),
Insulator diameter: 1.1 mm),
Standard length: 2 m
E3S-CL2:
4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section area: 0.2 mm2 (AWG24),
Insulator diameter: 1.2 mm),
16.5
54.5
16.1
9.1
Emitter, optical axis
Detecting axis
21
2
Standard length: 2 m
40
44.7
Note: The output selector, operation selector, and distance setting adjuster are located inside the cover.
8
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-
out notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or oth-
erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-
gation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsi-
ble for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were prop-
erly handled, stored, installed and maintained and not subject to contamina-
tion, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Compa-
nies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environ-
ments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for pub-
lished information.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon, 14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importa-
tion, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory 15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liabil-
ity and in addition to other remedies) cancel any unshipped portion of Prod-
ucts sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or set-
tle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery 16. Property; Confidentiality. Any intellectual property in the Products is the exclu-
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
sive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a.Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall 17. Export Controls. Buyer shall comply with all applicable laws, regulations and
constitute delivery to Buyer;
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security inter- 18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
est in the Products until the full purchase price is paid;
d.Delivery and shipping dates are estimates only; and
e.Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law princi-
ples). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability. If any provi-
sion hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Compa-
nies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original trans-
portation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-
ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Omron will provide applicable third party certification documents identifying 2. Programmable Products. Omron Companies shall not be responsible for the
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Prod- 3. Performance Data. Data presented in Omron Company websites, catalogs
user’s programming of a programmable Product, or any consequence thereof.
uct in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
and other materials is provided as a guide for the user in determining suitabil-
ity and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application require-
ments. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
(i) Outdoor use, uses involving potential chemical contamination or electrical 4. Change in Specifications. Product specifications and accessories may be
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equip-
ment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or prop-
erty. Please know and observe all prohibitions of use applicable to this Prod-
uct.
changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
OMRON INDUSTRIAL AUTOMATION • THE AMERICAS HEADQUARTERS
Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.55.59.01.43.00 • 001.800.556.6766 • mela@omron.com
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 001.800.556.6766 • mela@omron.com
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON EUROpE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands.
Fax: +31 (0) 23 568 13 88 www.industrial.omron.eu
• Tel: +31 (0) 23 568 13 00
•
Cat. No. CSM_E3S-CL_DS_E_4_2
08/12
Note: Specifications are subject to change.
© 2012 Omron Electronics LLC
Printed in U.S.A.
相关型号:
©2020 ICPDF网 联系我们和版权申明