H3BA-X8HA [OMRON]

Solid-state Timer;


型号：	H3BA-X8HA
厂家：	OMRON ELECTRONICS LLC
描述：	Solid-state Timer
文件：	总16页 (文件大小：1490K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Solid-state Timer

H3BA-X

Please read and understand this catalog before purchasing the products.

Please consult your OMRON representative if you have any questions or

comments. Refer to Warranty and Application Considerations (page 15),

and Safety Precautions (page 11).

Solid-state Timer with Single Time Range

and Operating Mode

• Time range: H3BA-X8HA (0.05 s to 12 h),

H3BA-X8HB (0.3 s to 30 h),

H3BA-X8HC (0.6 s to 60 h)

• Operating mode: ON-delay only

• Pin type: 8-pin only

Model Number Structure

■ Model Number Legend

H3BA-@8H@

1. Series

X: Single mode/range

2. Time range

A: 0.05 s to 12 h

B: 0.3 s to 30 h

C: 0.6 s to 60 h

Ordering Information

■ List of Models

Control output

Supply voltage

110 VAC (50/60 Hz)

8-pin models

H3BA-X8HA 110 VAC

Time-limit SPDT and Instantaneous SPDT

H3BA-X8HB 110 VAC

H3BA-X8HC 110 VAC

H3BA-X8HA 220 VAC

H3BA-X8HB 220 VAC

H3BA-X8HC 220 VAC

H3BA-X8HA 24 VDC

H3BA-X8HB 24 VDC

H3BA-X8HC 24 VDC

220 VAC (50/60 Hz)

24 VDC

■ Accessories (Order Separately)

Name/specifications

Models

Protective Cover

Track Mounting/

Front Connecting Socket

Y92A-48B

P2CF-08

8-pin

Back Connecting Socket

8-pin

P3G-08

Y92H-1

Y92H-2

Hold-down Clips (See note 2.)

For PL08 Socket

For PF085A Socket

Note: Hold-down Clips are sold in sets of two.

Solid-state Timer H3BA-X

Specifications

■ General

Item

H3BA-X8H

Operating mode

Pin type

A: ON-delay

8-pin

Input type

---

Output type

SPDT (time-limit) and SPDT (instantaneous)

Mounting method

Approved standards

DIN track mounting, surface mounting, and flush mounting

UL508, CSA C22.2 No.14, CCC : GB/T 14048.5 *

Conforms to EN61812-1 (Pollution degree 2 / Overvoltage category ΙΙΙ)

EMC

(EMI)

EN61812-1

Radiated Emissions:

Emission AC Mains:

(EMS)

EN 55011 class A

EN61812-1

ESD Immunity:

EN 61000-4-2:

6 kV contact discharge,

8 kV air discharge

Radiated Radio-Frequency

Electromagnetic Field Immunity:

EN 61000-4-3: 10 V/m (80 MHz to 1 GHz AM modulation)

3 V/m (1.4 GHz to 2 GHz AM modulation)

1 V/m (2 GHz to 2.7 GHz AM modulation)

10 V/m (900 MHz Pulse modulation)

Conducted disturbances:

Burst Immunity:

EN 61000-4-6: 10 V (0.15 MHz to 80 MHz)

EN 61000-4-4:

2 kV power line

2 kV I/O signal line

2 kV common mode

1 kV differential mode

Surge Immunity:

EN 61000-4-5:

Voltage dips:

Voltage interruptions:

EN 61000-4-11

* CCC certification requirements

Recommended fuse

0216005 (250 VAC, 5 A) manufactured by Littelfuse

Rated operating voltage Ue

Rated operating current Ie

AC-15: Ue: 250 VAC, Ie: 3 A

AC-13: Ue: 250 VAC, Ie: 5 A

DC-13: Ue: 30 VDC, Ie: 1.5 A

Rated insulation voltage

250 V

Rated impulse withstand voltage 4 kV (at 240 VAC)

(altitude: 2,000 m max.)

Conditional short-circuit current

1,000 A

■ Time Ranges

Time unit

Model

× 0.1 s

sec

× 10 s

min

× 10 m

hrs

Full scale setting

H3BA-X8HA

H3BA-X8HB

H3BA-X8HC

Set time 0.05 to 1.2

0.3 to 3

1.2 to 12

3 to 30

6 to 60

12 to 120

30 to 300

60 to 600

1.2 to 12

3 to 30

6 to 60

12 to 120

30 to 300

60 to 600

1.2 to 12

3 to 30

6 to 60

0.6 to 6

Solid-state Timer H3BA-X

■ Ratings

Item

H3BA-X8H

Rated supply voltage

(See notes 1 and 2)

110 VAC (50/60 Hz), 220 VAC (50/60 Hz), 24 VDC

Operating voltage range

(See note 3)

85% to 110% of rated supply voltage

Power reset

Minimum power-opening time: 0.1 s

110 VAC: Approx. 3.6 VA (1.6 W)

220 VAC: Approx. 7.8 VA (1.9 W)

24 VDC: Approx. 0.9 W

Power consumption

Control outputs

Contact:

5 A at 250 VAC, resistance load (cosφ = 1)

Note: 1. DC ripple rate: 20% max.

2. Models other than 24-VDC H3BA-X8H models cause an inrush current. Pay careful attention when attempting to turn on power to such

models with non-contact output from a device such as a sensor.

3. 90% or higher if the Timer is used continuously at a high ambient temperature.

■ Characteristics

Item

Accuracy of operating time

Setting error

H3BA-X8H

0.3% FS max. ( 0.3% 10 ms in a range of 1.2 s)

5% FS 0.05 s max.

Reset time

Min. power-opening time: 0.1 s max.

Min. pulse-input time:

50 ms

Influence of voltage

Influence of temperature

Insulation resistance

Dielectric strength

0.5% FS max. ( 0.5% 10 ms in a range of 1.2 s)

2% FS max. ( 2% 10 ms in a range of 1.2 s)

100 MΩ min. (at 500 VDC)

2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and exposed non-current-carrying metal

parts

2,000 VAC, 50/60 Hz for 1 min between control output terminals and operating circuit

1,000 VAC, 50/60 Hz for 1 min between contacts not located next to each other (750 VAC for H3BA-X8H)

Impulse withstand voltage

Noise immunity

1 kV (between power terminals)

2 kV (between current-carrying terminal and exposed non-current-carrying metal parts,

1.5 kV for 24-VDC models)

AC models: 1.5 kV (between power terminals), and 600 V (between input terminals),

square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)

DC models: 480 V (between power terminals), and 600 V (between input terminals),

square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)

Static immunity

Malfunction: 4 kV

Destruction: 8 kV

Vibration resistance

Shock resistance

Destruction: 10 to 55 Hz with 0.75-mm single amplitude each in three directions

Malfunction: 10 to 55 Hz with 0.5-mm single amplitude each in three directions

Destruction: 1,000 m/s²(approx. 100G) each in three directions

Malfunction: 100 m/s²(approx. 10G) each in three directions

Operating: –10°C to 55°C (with no icing)

Ambient temperature

Storage:

–25°C to 65°C (with no icing)

Ambient humidity

Life expectancy

Operating: 35% to 85%

Mechanical: 10 million operations min. (under no load at 1,800 operations/h)

Electrical: 100,000 operations min. (5 A at 250 VAC, resistive load at 360 operations/h)

Case color

Light gray (Munsell 5Y7/1)

IEC: IP40 (panel surface)

Approx. 95 g

Enclosure ratings

Weight

Solid-state Timer H3BA-X

Nomenclature

H3BA-X8H

Power Indicator (Green):

Lit when Timer operates.

Output Indicator (Orange):

Lit when Timer outputs.

Scale Range Display

Windows

min

Time Unit Selector

Select a unit from ×0.1sec,

sec, × 10sec, min, × 10min,

and hrs.

H3BA

Time setting knob (set time)

Operation

■ Block Diagrams

H3BA-X8H

AC (DC) input

Oscillation

circuit

Power supply

circuit

Counting

circuit

Output circuit

Indicator

circuit

Power-ON Output-ON

indicator indicator

Instantaneous

output circuit

Solid-state Timer H3BA-X

■ Basic Setting

■ Using the Setting Ring

Setting of Selector

Setting a Specific Time

The selectors can be turned clockwise and counterclockwise to

select the desired time range.

The selector has a snap mechanism that secures the selector at a

given position. Set the selector at a position at which it is secured. Do

not set it midway between two securing positions or a malfunction

could result from improper setting.

Mount the Panel Cover on the Timer, set the desired time with the

time setting knob, and place Time Setting Ring A onto the time

setting knob so that the time setting notch of Time Setting Ring A is

in the center of the reset lock position of the Panel Cover.

Time setting

Reset lock position

notch

Selection of Time Range

The desired time unit (× 0.1 sec, sec, × 10 sec, min, × 10 min, or hrs)

is displayed in the window below the time setting knob. A time range

is selected with the time range selector at the lower left corner of the

front panel, and the selected time range appears (in the window at

the lower right part) within the plastic frame of the time setting knob.

Time setting ring A Panel cover

Time setting notch

Setting position

min

Operating mode

display window

Example: To set the time to 10 s.

Time unit selector

Limiting the Setting Range

Example: To set a range of 10 and 20 s.

Time unit display window

Mount the Panel Cover on the Timer, set the time setting knob to 10 s

(the lower limit of the setting range), and place Time Setting Ring C

onto the time setting knob so that the stopper of Time Setting Ring C

is on the right edge of the reset lock position of the Panel cover. Next,

set the time setting knob to 20 s (the upper limit of the setting range),

place Time Setting Ring B onto the time setting knob so that the

stopper of Time Setting Ring B is on the left edge of the reset lock

position of the Panel Cover.

Setting of Time

Use the time setting knob to set the desired time.

Stopper

Reset lock position

Time setting

ring B

Time setting

ring C

Panel cover

Range

Solid-state Timer H3BA-X

■ Timing Chart

Note: 1. The minimum power-opening time (“Rt”) is 0.1 s.

2. The letter “t” in the timing charts stands for the set time and “t–a” means that the period is less than the time set.

H3BA-X8H

Operating mode

A: ON-delay

Timing chart

t - a

Power 2 and 7

Output relay (NC)

8 and 5

Output relay (NO)

8 and 6

and output indicator

Output relay (NC)

1 and 4

Output relay (NO)

1 and 3

Power indicator

Basic operation

Power

Output

Solid-state Timer H3BA-X

Dimensions

Note: All units are in millimeters unless otherwise indicated.

H3BA-X8H

63.7

13.6

0.7

44.8 × 44.8

39 dia.

8 pins

Dimensions with Set Ring

16.5

42 dia.

Time setting ring

Panel cover

Dimensions with Y92F-30 Flush Mounting Adapter

Panel Cutout

Panel

P3G Back Connecting Socket

(sold separately)

+0.6

0.5 R max.

−0

(N)

+0.6

−0

Note: The mounting panel thickness should be 1 to 5 mm.

Dimensions with Y92F-70 Flush Mounting Adapter

Panel Cutout

Panel

Adapter mounting hole Two, 4.5 dia.

R0.5 max.

65 to 66

52 to 53

45±

0.15

76±0.2

45±0.15

Solid-state Timer H3BA-X

Dimensions with Y92F-71 Flush Mounting Adapter

Panel Cutout

Panel

R0.5 max.

+0.5

−0

+0.5

−0

45±0.2

43±0.2

Note: The mounting panel thickness

+0.2

−0

should be 1 to 3.2 mm.

Track Mounting

Flush Mounting

86.4

H3BA-X8H

101.3

P3G-08

Y92F-30

2.3*

P2CF-08

Note: These dimensions vary with the kind of DIN track (reference

value).

■ Accessories (Order Separately)

Track Mounting/Front Connecting Socket

P2CF-08

Terminal Arrangement/

Internal Connections

(Top View)

Eight,

4.5

7.8

M3.5 7.5 sems

Surface Mounting Holes

Two, 4.5 dia. or two, M4

70 max.

35.4

Two, 4.5 dia.

holes

40±0.2

50 max.

20.3 max.

Back Connecting Socket

Terminal Arrangement/

Internal Connections

(Bottom View)

P3G-08

27 dia.

4.9

Solid-state Timer H3BA-X

Mounting Track

PFP-100N, PFP-50N

PFP-100N2

7.3±0.15

35±0.3

4.5

29.2

1.5

35±0.3

27±0.15

15 25

25 15

15 25

L: Length

1 m PFP-100N

50 cm PFP-50N

1 m

PFP-100N2

End Plate

PFP-M

Protective Cover

Y92A-48B

6.2

The protective cover protects the front panel, particularly the time

setting section, against dust, dirt, and water. It also prevents the set

value from being altered due to accidental contact with the time

setting knob.

1.8

35.5 35.3

1.8

Note: 1. The Y92A-48B Protective Cover is made of a hard plastic

and therefore it must be removed to change the timer set

value.

11.5

1.3

4.8

M4 × 8

pan head

screw

2. The Protective Cover cannot be mounted if the Panel Cov-

er (sold separately) is used on the Timer.

Y92A-48B

Spacer

PFP-S

34.8

44.3

16.5

Solid-state Timer H3BA-X

Time Setting Ring/Panel Cover

Hold-down Clip

There are two types of Panel Covers (Y92P-48GL, Y92P-48GB), all

of which are available in two colors. Use the most suitable type of

Panel Cover with the design of the scaling plate according to the

application.

Y92H-1

For PL08 Socket

Y92H-2

For PF085A Socket

When setting a given time for the Timer, use of the Y92S-27 or

Y92S-28 Time Setting Ring facilitates the time setting operation and

minimizes possible setting errors by operators.

The Time Setting Ring and Panel Cover should be used as a pair.

Setting a specific time Time Setting Ring A (Y92S-27) and Panel

Cover (Y92P-48GL, -48GB)

Limiting the setting

range

Time Setting Ring B or C (Y92S-28), and

Panel Cover (Y92P-48GL, -48GB)

Y92S-27

Time Setting A

Y92S-28

Time Setting B

Y92S-28

Time Setting C

Y92P-48GL

Light Gray

Y92P-48GB

Black

Installation

■ Terminal Arrangement

H3BA-X8H (Contact Output)

Power supply

(+)(~)

Note: The delayed contacts of conventional timers

are shown as follows:

The instantaneous contacts of conventional

timers are shown as follows:

Solid-state Timer H3BA-X

Safety Precautions

Warning Indications

■ Precautions for Safe Use

Please observe the following precautions for safe use of this product.

Indicates a potentially hazardous

situation which, if not avoided, may

result in minor or moderate injury or in

property damage.

CAUTION

Environmental Precautions

Supplementary comments on what to

do or avoid doing, to use the product

safely.

Store the Timer within specified ratings. If the Timer has been stored

at -10°C or lower, let it stand for 3 hours or longer at room

temperature before turning ON the power supply.

Precautions for

Safe Use

Use the Timer within the specified ratings for operating temperature

and humidity.

Supplementary comments on what to

do or avoid doing, to prevent failure to

operate, malfunction or undesirable

effect on product performance.

Precautions for

Correct Use

Do not operate the Timer in locations subject to sudden or extreme

changes in temperature, or locations where high humidity may result

in condensation.

Meaning of Product Safety Symbols

Do not use the Timer in locations subject to excessive dust, corrosive

gas, or direct sunlight.

Do not use the Timer in locations subject to vibration or shock.

Extended use in such locations may result in damage due to stress.

Used to warn of the risk of electric shock under

specific conditions.

Install the Timer well away from any sources of static electricity, such

as pipes transporting molding materials, powders, or liquids.

Used to warn of the risk of minor injury caused by

high temperatures

Usage Precautions

Install a switch or circuit breaker that allows the operator to

immediately turn OFF the power, and label it to clearly indicate its

function.

Used for general mandatory action precautions

for which there is no specified symbol.

Pay careful attention to polarity to prevent wrong connections when

wiring terminals.

Internal elements may be destroyed if a voltage outside the rated

voltage is applied.

Use to indicate prohibition when there is a risk of

minor injury from electrical shock or other source

if the product is disassembled.

Maintain voltage fluctuations in the power supply within the specified

range.

The Timer uses a transformerless power supply. Do not touch the

input terminals while the supply voltage is being applied, otherwise

an electric shock may occur.

CAUTION

Minor electric shock may occasionally occur. Do not

disassemble the product or touch the interior of the Timer.

Minor burns may occasionally occur. Do not touch the

product while power is being supplied or immediately

after power is turned OFF.

Minor fires may occasionally occur. Tighten terminal

screws to a torque of 1.08 N·m so that they do not

become loose.

Minor electric shock may occasionally occur during

operation. Install the terminal cover.

Minor electric shock, fire, or malfunction may occasionally

occur.

Do not allow metal fragments, lead wire scraps, or chips

from processing during installation to fall inside the Timer.

Solid-state Timer H3BA-X

Others

■ Precautions for Correct Use

When conducting a dielectric test, impulse voltage test, or insulation

resistance test between the electric circuit and non-current-carrying

metal parts of the Timer mounted to a control panel, be sure to take

the following steps. These steps will prevent the internal circuitry of

the Timer from damage that may be caused if a machine on the

control panel has an improper dielectric strength or insulation

resistance.

Changing the Setting

Do not change the time unit, time range, or operation mode while the

Timer is in operation, otherwise the Timer may malfunction.

Connecting the Operating Power

Supply

The H3BA-X8H contains a capacitor-drop power circuit. Use a

sinusoidal power supply with a commercial frequency. Do not use

power supplies with a high frequency component (such as inverter

power supplies) for Timers with 110 or 220-VAC specifications. Using

these power supplies can damage internal circuits.

1. Separate the Timer from the circuitry of the control panel by

disconnecting the socket from the Timer or wires.

2. Short-circuit all terminals of the Timer.

If any device with no-contact output, such as a proximity sensor,

photoelectric sensor, or SSR, is directly connected to the Timer,

current leakage from the device may cause Timer malfunction. Be

sure to test the device with the Timer before using the device for

actual applications.

If voltages other than the rated voltage is applied, the internal

components may be damaged. The internal element (varistor) will be

damaged if a voltage of higher than 100 VAC is applied to the 24-

VDC line.

Before using the Timer to switch inductive loads, be sure to connect

a surge absorbing element to the Timer in order to prevent the Timer

from malfunction and damage. A diode is an example of a surge

absorbing element for DC circuits and a surge absorber is an

example of a surge absorbing element for AC circuits.

Connect the power supply voltage through a relay or switch in such a

way that the voltage reaches a fixed value immediately or the Timer

may not be reset or a timer error could result.

Do not leave the Timer in time-up condition for a month or longer in

places with high temperatures, otherwise the internal parts, such as

an electrolytic capacitor, of the Timer may be damaged. Use the

Timer with an appropriate relay so that the Timer will not be left in

time-up condition for a long time.

A DC power supply can be connected if its ripple factor is 20% or

less and the mean voltage is within the rated operating voltage range

of the Timer.

If the Timer is mounted in contact with a mounting surface, the

service life of internal parts may be shortened. Provide at least 10

mm between the Timer and the mounting surface to prolong the

service life of the Timer.

Operating Time Setting

When setting the operating time, do not turn the setting knob beyond

its scale range. For precise time setting, conduct operation tests by

adjusting the setting knob.

When the Timer is reset right after the Timer goes into time-up

condition, be sure to provide the Timer with an appropriate circuit

configuration considering the resetting time of the Timer so that a

sequential error will not result.

The accuracy of the operating time of the Analog Timer is indicated

by the percentage value on the basis of the full-scale time. The

absolute fluctuation value will not be improved by changing the time

setting. Therefore, when selecting the model, be sure that the

application will be able to use a time setting as close as the full-scale

time setting of the Timer.

The Timer uses the constant value read method. Be careful when

changing the set value because the output of the Timer will be ON

when the set value coincides with the count value.

Be sure that the casing of the Timer is free from organic solvents,

such as paint thinner and benzene, strong acid, and alkali solvents,

which will damage the casing.

Note: It is impossible to connect more than two Timers in parallel.

Solid-state Timer H3BA-X

When using the US08, be sure to use 10.5-dia. max. multi-conductor

cable or 3-dia. max. insulated stranded wire for wiring.

■ Mounting

When the Y92F-30, Y92F-70 or Y92F-71 Flush Mounting Adapter is

used, just insert the Timer into the square panel hole. If the panel

coating is too thick and the hooks do not click, spread open the

hooks appropriately to the left and right after inserting the Timer to

the hole.

Surface Mounting

There is no particular restriction on surface mounting directions, but

be sure that the Timer is securely mounted horizontally.

Spread open the hooks to the left and right.

Panel

P2CF Socket

When mounting the Timer vertically with the P2CF Socket, consider

the movable hooks and be sure that there is a 20-mm space on each

of the upper and lower parts of the Socket.

The illustration is an ex

ample with the Y92F-70.

Duct

Hook

Spread open the hooks to the left and right.

P2CF-08

■ Dismounting

Surface Mounting with P2CF

Panel

PL Socket

1. Secure the Socket to the panel surface with screws and insert the

F-shaped hook into the sockets.

2. Connect the Timer to the Socket and press the tip of each hook

Panel Mounting

by hand.

Loosen the screws of the Flush Mounting Adapter, spread open the

hooks, and remove the Mounting Adapter.

Panel Mounting

When the Y92F-30, Y92F-70, Y92F-71 Mounting Adapter is used,

press the hook inwards with the thumb and index finger of both

hands, and press the Timer towards the front side.

When the Y92F-30 Flush Mounting Adapter is used, insert the Timer

into the square hole from the front side of the panel and put on the

Flush Mounting Adapter from the rear side of the Timer. Press the

Flush Mounting Adapter so that the space between the Flush

Mounting Adapter and the panel is reduced as much as possible,

and secure the Flush Mounting Adapter with screws.

Panel

Screw

Y92F-30

Solid-state Timer H3BA-X

Read and Understand this Catalog

Please read and understand this catalog before purchasing the product. Please consult your OMRON representative if you have

any questions or comments.

Warranty and Limitations of Liability

WARRANTY

OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year

(or other period if specified) from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT,

MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER

ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET

THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS

OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON

CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.

In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE

PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED,

INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE

MODIFICATION OR REPAIR.

Application Considerations

SUITABILITY FOR USE

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the

product in the customer's application or use of the product.

Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will

be used.

Know and observe all prohibitions of use applicable to this product.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT

ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON

PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR

SYSTEM.

PROGRAMMABLE PRODUCTS

OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.

Disclaimers

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with

your OMRON representative at any time to confirm actual specifications of purchased product.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

PERFORMANCE DATA

Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a

warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application

requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability.

OMRON Corporation

Tokyo, JAPAN

Industrial Automation Company

Authorized Distributor:

Contact: www.ia.omron.com

Regional Headquarters

OMRON EUROPE B.V.

Wegalaan 67-69-2132 JD Hoofddorp

The Netherlands

OMRON ELECTRONICS LLC

One Commerce Drive Schaumburg,

IL 60173-5302 U.S.A.

Tel: (31)2356-81-300/Fax: (31)2356-81-388

Tel: (1) 847-843-7900/Fax: (1) 847-843-7787

In the interest of product improvement,

specifications are subject to change without notice.

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower,

200 Yin Cheng Zhong Road,

PuDong New Area, Shanghai, 200120, China

Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200

OMRON ASIA PACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 (Lobby 2),

Alexandra Technopark,

Singapore 119967

Tel: (65) 6835-3011/Fax: (65) 6835-2711

CSM_1_4_1018

Cat. No. L126-E1-01

0313 (O)

H3BA-X8HA [OMRON]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E