FODM214AR2 [ONSEMI]
Single Channel, AC/DC Sensing Input, Phototransistor Optocoupler In Half-Pitch Mini-Flat 4-Pin Package;型号: | FODM214AR2 |
厂家: | ONSEMI |
描述: | Single Channel, AC/DC Sensing Input, Phototransistor Optocoupler In Half-Pitch Mini-Flat 4-Pin Package |
文件: | 总9页 (文件大小:305K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
FODM214, FODM217 Series
Single Channel, AC/DC
Sensing Input,
Phototransistor
Optocoupler In Half-Pitch
Mini-Flat 4-Pin Package
www.onsemi.com
The FODM217 series consist of a gallium arsenide infrared emitting
diode driving a phototransistor. The FODM214 series consist of two
gallium arsenide infrared emitting diodes connected in inverse parallel
for AC operation. Both were built in a compact, half−pitch, mini−flat,
4−pin package. The lead pitch is 1.27 mm.
MFP4 2.5x4.4, 1.27P
CASE TBD
Features
• Current Transfer Ratio Ranges from 20 to 600%
at I = 1 mA, V = 5 V, T = 25°C
F
CE
A
MARKING DIAGRAM
♦ FODM214 − 20 to 400%
♦ FODM214A − 50 to 250%
at I = 5 mA, V = 5 V, T = 25°C
F
CE
A
♦ FODM217A − 80 to 160%
♦ FODM217B − 130 to 260%
♦ FODM217C − 200 to 400%
♦ FODM217D − 300 to 600%
• Safety and Regulatory Approvals:
♦ UL1577, 3750 VAC
♦ DIN EN/IEC60747−5−5, 565 V Peak Working Insulation Voltage
• Applicable to Infrared Ray Reflow, 260°C
for 1 min
RMS
1.
2.
3.
4.
5.
6.
ON = Corporate Logo
21xx = Device Number
V
X
YY
R1
= DIN EN/IEC60747−5−5 Option
= One−Digit Year Code
= Digit Work Week
Typical Applications
= Assembly Package Code
• Primarily Suited for DC−DC Converters
• For Ground Loop Isolation, Signal to Noise Isolation
• Communications – Adapters, Chargers
• Consumer – Appliances, Set Top Boxes
• Industrial – Power Supplies, Motor Control, Programmable Logic
Control
PIN CONNECTIONS
ORDERING INFORMATION
See detailed ordering and shipping information on page 7 of
this data sheet.
© Semiconductor Components Industries, LLC, 2018
1
Publication Order Number:
August, 2019 − Rev. 2
FODM214/D
FODM214, FODM217 Series
SAFETY AND INSULATIONS RATING
As per DIN EN/IEC 60747−5−5, this optocoupler is suitable for “safe electrical insulation” only within the safety limit data.
Compliance with the safety ratings shall be ensured by means of protective circuits.
Parameter
Characteristics
Installation Classifications per DIN VDE 0110/1.89 Table 1,
For Rated Mains Voltage
< 150 VRMS
< 300 VRMS
I–IV
I–III
Climatic Classification
55/110/21
2
Pollution Degree (DIN VDE 0110/1.89)
Comparative Tracking Index
175
Symbol
Parameter
Input−to−Output Test Voltage, Method A, V
Value
Unit
V
PR
x 1.6 = V
,
904
Vpeak
IORM
PR
Type and Sample Test with t = 10 s, Partial Discharge < 5 pC
m
Input−to−Output Test Voltage, Method B, V
x 1.875 = V
,
1060
Vpeak
IORM
PR
100% Production Test with t = 1 s, Partial Discharge < 5 pC
m
Maximum Working Insulation Voltage
Highest Allowable Over−Voltage
External Creepage
565
4,000
≥ 5
V
Vpeak
Vpeak
mm
IORM
V
IOTM
≥ 5
External Clearance
mm
≥ 0.4
150
DTI
Distance Through Insulation (Insulation Thickness)
mm
T
S
°C
Case Temperature (Note 1)
Input Current (Note 1)
Output Power (Note 1)
200
300
mA
mW
W
I
S,INPUT
P
S,OUTPUT
9
R
Insulation Resistance at T , V = 500 V (Note 1)
> 10
IO
S
IO
1. Safety limit values – maximum values allowed in the event of a failure.
ABSOLUTE MAXIMUM RATINGS (T = 25°C unless otherwise specified.)
A
Symbol
Parameter
Value
Units
T
STG
Storage Temperature
−55 to +150
°C
T
Operating Temperature
Junction Temperature
Lead Solder Temperature
−55 to +110
−55 to +125
260 for 10 sec
°C
°C
°C
OPR
T
J
T
SOL
(Refer to Reflow Temperature Profile)
EMITTER
I
Continuous Forward Current
Peak Forward Current (1 ms pulse, 300 pps)
Reverse Input Voltage
50
1
mA
A
F(average)
IF
(peak)
V
R
6
V
PD
Power Dissipation (Note 2)
70
mW
LED
DETECTOR
I
Continuous Collector Current
Collector−Emitter Voltage
50
80
7
mA
V
C(average)
V
V
CEO
Emitter−Collector Voltage
V
ECO
PD
Collector Power Dissipation (Note 2)
150
mW
C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
2. Functional operation under these conditions is not implied. Permanent damage may occur if the device is subjected to conditions outside
these ratings.
www.onsemi.com
2
FODM214, FODM217 Series
ELECTRICAL CHARACTERISTICS T = 25°C unless otherwise specified
A
Symbol
Parameter
Device
Conditions
Min.
Typ.
1.2
30
Max.
Units
EMITTER
FODM214
FODM217
FODM217
All
Forward Voltage
VF
IF = 20 mA
V
1.4
IF = 20 mA
Reverse Current
IR
VR = 4 V
10
mA
CT
Terminal Capacitance
V = 0 V, f = 1 kHz
250
pF
DETECTOR
BV
BV
Collector−Emitter Breakdown Voltage
Emitter−Collector Breakdown Voltage
Collector Dark Current
All
All
All
I
I
= 0.1 mA, IF = 0 mA
80
7
V
V
CEO
ECO
C
= 10 mA, IF = 0 mA
E
I
V
= 50 V, IF = 0 mA
100
nA
CEO
CE
TRANSFER CHARACTERISTICS T =25°C unless otherwise specified
A
Symbol
Parameter
Device
Conditions
Min.
20
Typ.
Max.
400
250
160
260
400
Units
CTR
%
I = 1 mA, V = 5 V
Current Transfer Ratio
(collector−emitter)
FODM214
FODM214A
FODM217A
FODM217B
FODM217C
CE
F
CE
50
I = 5 mA, V = 5 V
80
F
CE
130
200
FODM217D
FODM214
FODM217
FODM214
FODM217
FODM214
FODM217
FODM214
FODM217
300
0.2
4
600
2.5
30
I
Collector Current
I = 1 mA, V = 5 V
mA
%
C
F
CE
I = 5 mA, V = 5 V
F
CE
CTR
Saturated Current Transfer Ratio
Collector Current
I = 8 mA, V = 0.4 V
F CE
(SAT)
60
I = 8 mA, V = 0.4 V
F
CE
I
I = 8 mA, V = 0.4 V
mA
V
C(SAT)
F
CE
4.8
I = 8 mA, V = 0.4 V
F
CE
V
Collector−Emitter Saturation Voltage
I = 8 mA, I = 2.4 mA
F C
CE(SAT)
0.4
I = 8 mA, I = 2.4 mA
F
C
SWITCHING CHARACTERISTICS T = 25°C unless otherwise specified
A
Symbol
Parameter
Turn On Time
Conditions
= 2 mA, V = 10 V, R = 100 W
Min.
Typ.
Max.
Units
ms
t
I
C
I
C
I
C
3
3
3
3
ON
CE
L
t
Turn Off Time
= 2 mA, V = 10 V, R = 100 W
ms
OFF
CE
L
t
R
Output Rise Time (10%−90%)
Output Fall Time (90%−10%)
= 2 mA, V = 10 V, R = 100 W
ms
CE
L
t
F
IC = 2 mA, V = 10 V, R = 100 W
ms
CE
L
ISOLATION CHARACTERISTICS
Symbol
Parameter
Conditions
Freq = 60 Hz, t = 1.0 min,
Min.
Typ.
Max.
Units
V
ISO
Input−Output Isolation Voltage
3,750
VAC
RMS
I
v 10 mA (Note 3, 4)
I−O
10
R
C
Isolation Resistance
Isolation Capacitance
V
= 500 V (Note 3)
5 x 10
W
ISO
ISO
I−O
Frequency = 1 MHz
0.6
1.0
pF
3. Device is considered a two terminal device: Pin 1 and 2 are shorted together and Pins 3 and 4 are shorted together.
4. 3,750 VACRMS for 1 minute duration is equivalent to 4,500 VACRMS for 1 second duration.
www.onsemi.com
3
FODM214, FODM217 Series
TYPICAL CHARACTERISTICS
160
140
120
100
80
80
60
40
20
0
60
40
20
0
0
25
50
75
100
125
0
25
50
75
100
125
T , AMBIENT TEMPERATURE (5C)
A
T , AMBIENT TEMPERATURE (5C)
A
Figure 1. Collector Power Dissipation vs. Ambient
Temperature
Figure 2. LED Power Dissipation vs. Ambient
Temperature
100
−2.4
−2.0
−1.6
−1.2
−0.8
−0.4
75°C
110°C
-55°C
10
25°C
1
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
1
10
I , FORWARD CURRENT (mA)
100
V , FORWARD VOLTAGE (V)
F
F
Figure 3. Forward Current vs. Forward Voltage
Figure 4. Forward Voltage Temperature Coefficient vs.
Forward Current
5
30
25
0.5 mA
4
1 mA
3 mA
FODM217 IF = 5 mA
20
3
2
1
0
5 mA
7 mA
10 mA
15
10
5
FODM214 IF = 1 mA
0
0
5
10
15
20
0
5
10
I , FORWARD CURRENT (mA)
F
V , COLLECTOR−EMITTER CURRENT (V)
CE
Figure 5. Collector Emitter Voltage vs. Forward Current Figure 6. Collector Current vs. Collector−Emitter
Voltage
www.onsemi.com
4
FODM214, FODM217 Series
30
25
20
15
10
5
0.1
10 V
5 V
VCE= 0.4 V
0.01
0.001
FODM217 IF = 5 mA
FODM214 IF = 1 mA
0.0001
0
0.0
0.0001
0.001
0.01
0.1
0.5
1.0
V , COLLECTOR−EMITTER VOLTAGE (V)
CE
I , FORWARD CURRENT (mA)
F
Figure 7. Collector Current vs.
Small Collector−Emitter Voltage
Figure 8. Collector Current vs.
Forward Current
1000
1E−5
1E−6
1E−7
1E−8
1E−9
1E−10
1E−11
10 V
5 V
VCE= 48 V
24 V
VCE= 0.4 V
100
5 V
10 V
10
0.0001
0.001
0.01
0.1
−25
0
25
50
75
100
T , AMBIENT TEMPERATURE (5C)
A
I , FORWARD CURRENT (A)
F
Figure 9. Collector Dark Current vs.
Ambient Temperature
Figure 10. Current Transfer Ratio vs.
Forward Current
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0.00
100
10
1
20 mA
10 mA
5 mA
IF = 8 mA
IC = 2.4 mA
IF = 1 mA
IC = 0.2 mA
1 mA
IF = 20 mA
IC = 1 mA
I
F= 0.5 mA
0.1
−25
−25
0
25
50
75
100
0
25
50
75 100
T , AMBIENT TEMPERATURE (5C)
A
T , AMBIENT TEMPERATURE (5C)
A
Figure 11. Collector−Emitter Saturation vs.
Figure 12. Collector Current vs.
Ambient Temperature
Ambient Temperature
www.onsemi.com
5
FODM214, FODM217 Series
1000
100
10
100
VCC= 10 V
TA = 25 °C
VCC= 5 V
IF = 16 mA
IC= 2 mA
tOFF
W
RL= 100
F
t
tOFF
tON
10
tR
tON
tF
1
tR
0.1
1
−25
1
10
100
0
25
50
75
100
R , LOAD RESISTANCE (kW)
L
T , AMBIENT REMPERATURE (5C)
A
Figure 13. Switching Time vs. Load Resistance
Figure 14. Switching Time vs. Ambient
Temperature
TEST CIRCUIT
V
CC
R
L
V
O
1
2
4
3
I
F
t
R
t
F
V
O
90%
10%
I Monitor
F
R
M
t
t
ON
OFF
Figure 15. Test Circuit for Switching Time
www.onsemi.com
6
FODM214, FODM217 Series
REFLOW PROFILE
Figure 16. Reflow Profile
Profile Freature
Pb−Free Assembly Profile
Temperature Min. (Tsmin)
Temperature Max. (Tsmax)
Time (t ) from (Tsmin to Tsmax)
150°C
200°C
60–120 seconds
3°C/second max.
217°C
S
Ramp−up Rate (t to t )
L
P
Liquidous Temperature (T )
L
Time (t ) Maintained Above (T )
60–150 seconds
260°C +0°C / –5°C
30 seconds
L
L
Peak Body Package Temperature
Time (t ) within 5°C of 260°C
P
Ramp−down Rate (T to T )
6°C/second max.
8 minutes max.
P
L
Time 25°C to Peak Temperature
ORDERING INFORMATION (Note 5)
Part Number
Package
Packing Method
Tube (100 units)
FODM214A
SOP 4−Pin
SOP 4−Pin
FODM214AR2
FODM214AV
FODM214AR2V
Tape and Reel (3000 units)
Tube (100 units)
SOP 4−Pin, DIN EN/IEC60747−5−5 Option
SOP 4−Pin, DIN EN/IEC60747−5−5 Option
Tape and Reel (3000 units)
5. The product orderable part number system listed in this table also applies to the FODM214, FODM217A, FODM217B, FODM217C, and
FODM217D products.
www.onsemi.com
7
FODM214, FODM217 Series
PACKAGE DIMENSIONS
MFP4 2.5x4.4, 1.27P
CASE TBD
ISSUE TBD
1.27 0.25
3
4
0.61
7.87 4.83
1.52
4.40 0.20
0.40 0.10
1.27
1
2
LAND PATTERN RECOMMENDATION
5.44 0.30
TOP VIEW
2.60 0.30
0.25 0.05
2.00 0.20
0.1 0.10
7 0.45
DETAIL A
SIDE VIEW
FRONT VIEW
NOTES:
GAGE
A. NO INDUSTRY STANDARD APPLIES TO
THIS PACKAGE
PLANE
B. ALL DIMENSIONS ARE IN MILLIMETERS
4°
C. DIMENSIONS DO NOT INCLUDE MOLD
FLASH OR BURRS
SEATING
PLANE
D. DRAWING FILENAME: MKT−MFP04DrevA
MIN 0.5
1.30 0.30
0.127
DETAIL A
www.onsemi.com
8
FODM214, FODM217 Series
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
◊
FODM214/D
相关型号:
FODM214AR2V
Single Channel, AC/DC Sensing Input, Phototransistor Optocoupler In Half-Pitch Mini-Flat 4-Pin Package
ONSEMI
FODM214AV
Single Channel, AC/DC Sensing Input, Phototransistor Optocoupler In Half-Pitch Mini-Flat 4-Pin Package
ONSEMI
FODM217
Single Channel, AC/DC Sensing Input, Phototransistor Optocoupler In Half-Pitch Mini-Flat 4-Pin Package
ONSEMI
©2020 ICPDF网 联系我们和版权申明