MICRORD-10035-MLP-TR-E [ONSEMI]
NIR-Enhanced, Single Pixel Silicon Photomultiplier (SiPM);
| 型号： | MICRORD-10035-MLP-TR-E |
| 厂家： | 
ONSEMI |
| 描述： | NIR-Enhanced, Single Pixel Silicon Photomultiplier (SiPM) |
| 文件： | 总9页 (文件大小：1472K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
NIR-Enhanced, Single Pixel
Silicon Photomultiplier
(SiPM)
Product Preview
RD-Series SiPM Sensors
www.onsemi.com
The MicroRD family of sensors are a range of Silicon
Photomultipliers (SiPM) that provide market−leading sensitivity in
the red and NIR region of the electromagnetic spectrum. The
MicroRD SiPMs feature high responsivity, fast signal response and
a low temperature coefficient of operating voltage, all achieved at a
low bias voltage. The sensor is packaged in a compact and robust MLP
(micro lead frame) package that is suitable for reflow solder processes.
The product is designed for high−volume, automotive applications
and will be qualified to the AEC−Q102 standard.
SiPM sensors are an improvement over avalanche photodiodes
(APD) and PIN diodes due to their high gain and single photon
sensitivity. For LiDAR applications this enables the detection of low
reflectivity targets at very long distances.
It is strongly recommended that those new to SiPM sensors consult
the Introduction to Silicon Photomultipliers application note.
Evaluation boards (SMA and SMTPA boards – see pages 4−5)
are also available for these products.
ORDERING INFORMATION
See detailed ordering and shipping information on page 6 of
this data sheet.
KEY SENSOR AND PACKAGE SPECIFICATIONS
Parameter
Silicon Process
Value
RD
Unit
Comment
NIR enhanced
Number of Pixels
Active Area
Single pixel
1 × 1
mm
Microcell Size
10
4370
44
20
35
625
77
mm
Number of Microcells per Pixel
Microcell Fill Factor
Package Size
1620
65
%
1.5 × 1.8 × 0.65
Analog
mm
MLP Package (W × L × H)
Output Type
Standard and Fast output per pixel
This document contains information on a product under development. ON Semiconductor reserves the right to change or discontinue this product without notice.
© Semiconductor Components Industries, LLC, 2019
1
Publication Order Number:
May, 2020 − Rev. P2
MICRORD−SERIES/D
RD−Series SiPM Sensors
PERFORMANCE SPECIFICATIONS
Typical values are measured at 21°C. Minimum and Maximum values (when available) will take into account operation over the full
temperature range of −40°C to 105°C. All measurements made at Vop (see biasing table below). All timing measurements acquired using
a MicroRD−SMA EVB.
Microcell
Variant
Parameter
PDE @ 905 nm
Min
Typ
Max
Unit
Comment
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
6.0
9.1
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
%
%
10.2
1
%
Dark Count Rate
Optical Crosstalk
Gain
Mcps
kcps
kcps
%
800
550
25
25
%
25
%
6
6
6
0.7 × 10
0.9 × 10
1.9 × 10
13
Afterpulsing Probability
0.5 Photoelectron level
RC time constant
%
%
3
1
%
Microcell Recovery Time
Constant
18
ns
ns
ns
ns
ns
ns
ns
ns
ns
ps
ps
ps
21
55
Microcell Rise Time
1.9
1.8
0.46
1.3
Fast Output Pulse Width
Fast Output Rise Time
FWHM
1.5
2.6
240
350
530
BIAS PARAMETERS
Microcell
Size
Parameter
Min
Typ
Max
Unit
Comment
Breakdown Voltage (Vbr) *
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
10 mm
20 mm
35 mm
−
−
−
−
−
−
21.9
22.4
22.4
12.0
7.0
−
−
−
−
−
−
V
V
V
V
V
V
Over Voltage (Vov)
Typical values recommended
for operation and used for
characterization
3.2
Operating Bias
Vop = Vbr + Vov
Temperature Coefficient of Vbr
Contact
sensl_questions@onsemi.com
*The breakdown voltage (Vbr) is defined as the value of the voltage intercept of a straight line fit to a plot of √I vs V, where I is the current and
V is the bias voltage.
www.onsemi.com
2
RD−Series SiPM Sensors
ABSOLUTE MAXIMUM RATINGS
Parameter
Value
3
Unit
mA
°C
Comment
At typical Vop
Maximum Current
Maximum Storage Temperature
Operating Temperature Range
125
−40 to +105
°C
Ambient temperature
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
PACKAGE SPECIFICATIONS
Parameter
Value
TBD
TBD
46
Unit
Comment
ESD−HBM
ESD−CDM
θ
JC
θ
JA
°C/W
°C/W
731
MSL
MSL 3 for tape and reel
(TR delivery option)
MSL 4 for cut tape
(TR1 delivery option)
PIN ASSIGNMENT
3
4
Pin Number
Pin Assignment
Anode
1
2
3
4
Fast Output
Cathode
No Connect*
*The ‘No Connect’ pins are electrically isolated and should be
soldered to a ground (or bias) plane to help with heat dissipation.
2
1
BOTTOM VIEW
APPLICATION ADVICE
• For biasing and readout, please consult the AND9782/D Application note
• For handling and soldering advice, please consult the AND9788/D Application note
www.onsemi.com
3
RD−Series SiPM Sensors
SMA BIASING BOARD (MicroRD−SMA−100XX)
The MicroRD−SMA is a printed circuit board (PCB) that
MicroRD−SMA−100XX
Function
can facilitate the evaluation of the MicroRD MLP sensors.
The board has three female SMA connectors for connecting
the bias voltage, the standard output from the cathode, and
the fast output signal. The output signals can be connected
directly to a 50 W−terminated oscilloscope for viewing. The
biasing and output signal tracks are laid out in such a way as
to preserve the fast timing characteristics of the sensor.
The MicroRD−SMA is recommended for users who
require a plug−and−play set−up to quickly evaluate
MicroRD sensors with optimum timing performance. The
board also allows the signal from the cathode−anode readout
to be observed at the same time as the fast output. The
outputs can be connected directly to the oscilloscope or
measurement device, but external preamplification may be
required to boost the signal. The table below lists the SMA
board connections. The SMA board electrical schematics
are available to download in the Board Reference Design
document.
Output
Vbias
Fout
Negative bias input (anode)
Fast output
Sout
Standard output (cathode)
Figure 1. SMA Biasing Board
Figure 2. Schematic of SMA Biasing Board
www.onsemi.com
4
RD−Series SiPM Sensors
PIN ADAPTER BOARD (MicroRD−SMTPA−100XX)
The Pin Adapter board (SMTPA) is a small PCB board
that houses the SIPM sensor and has through−hole pins to
allow its use with standard sockets or probe clips. This
product is useful for those needing a quick way to evaluate
the MLP−packaged sensor without the need for specialist
surface−mount soldering. While this is a ‘quick fix’ suitable
for many evaluations, it should be noted that the timing
performance from this board will not be optimized and if the
best possible timing performance is required, the
MicroRD−SMA−100XX is recommended. The SMTPA
circuit schematic is shown below. Please consult the Biasing
and Readout Application Note for further information on
biasing. The SMTPA board electrical schematics are
available to download in the Board Reference Design
document.
Figure 3. Pin Adapter Board
MicroRD−SMTPA−100XX
Pin. No.
Function
Anode
1
2
3
4
5
Fast output
Cathode
Ground
Figure 4. Schematic of Pin Adapter Board
Ground
www.onsemi.com
5
RD−Series SiPM Sensors
ORDERING INFORMATION
ORDERING INFORMATION
Microcell
Size
Shipping
Format*
Part Number
MicroRD−10010−MLP−TR
MicroRD−10010−MLP−TR1
MicroRD−10010−MLP−TR−E
Product Description
10 mm
1 mm × 1 mm RD−Series Silicon Photomultiplier pixel
Tape and Reel
Cut Tape
(NIR enhanced) with fast output, packaged in MLP
Unqualified prototype part of the MicroRD−10010−MLP
Depends upon
Quantity Ordered
MicroRD−SMA−10010−GEVB
MicroRD−SMTPA−10010−GEVB
MicroRD−10010−MLP sensor mounted onto a PCB with
ESD Package
SMA connectors for bias and outputs.
MicroRD−10010−MLP packaged sensor mounted onto
a pin adapter board.
ESD Package
MicroRD−10020−MLP−TR
MicroRD−10020−MLP−TR1
MicroRD−10020−MLP−TR−E
20 mm
1 mm × 1 mm RD−Series Silicon Photomultiplier pixel
Tape and Reel
Cut Tape
(NIR enhanced) with fast output, packaged in MLP
Unqualified prototype part of the MicroRD−10020−MLP
Depends upon
Quantity Ordered
MicroRD−SMA−10020−GEVB
MicroRD−SMTPA−10020−GEVB
MicroRD−10020−MLP sensor mounted onto a PCB with
ESD Package
ESD Package
SMA connectors for bias and outputs.
MicroRD−10020−MLP packaged sensor mounted onto
a pin adapter board.
MicroRD−10035−MLP−TR
MicroRD−10035−MLP−TR1
MicroRD−10035−MLP−TR−E
35 mm
1 mm × 1 mm RD−Series Silicon Photomultiplier pixel
Tape and Reel
Cut Tape
(NIR enhanced) with fast output, packaged in MLP
Unqualified prototype part of the MicroRD−10035−MLP
Depends upon
Quantity Ordered
MicroRD−SMA−10035−GEVB
MicroRD−SMTPA−10035−GEVB
MicroRD−10035−MLP sensor mounted onto a PCB with
ESD Package
ESD Package
SMA connectors for bias and outputs.
MicroRD−10035−MLP packaged sensor mounted onto
a pin adapter board.
*For information on tape and reel specifications, please contact sensl_questions@onsemi.com.
www.onsemi.com
6
RD−Series SiPM Sensors
PACKAGE DIMENSIONS
CWDFN4 1.5x1.8, 0.8P
CASE 512AL
ISSUE O
www.onsemi.com
7
RD−Series SiPM Sensors
EVALUATION BOARD DIMENSIONS
(MicroRD−SMA−100XX−GEVB)
Top View
Side View
Side View
Bottom View
www.onsemi.com
8
RD−Series SiPM Sensors
EVALUATION BOARD DIMENSIONS
(MicroRD−SMTPA−100XX−GEVB)
Bottom View
Top View
Side View
Detector
Side View
Pin Assignments
Pin #
RD Series
Anode
1
2
3
4
5
Fast Output
Cathode
PCB Ground
Jumper to PCB Ground (0 Ohm)
Top View
Bottom View
SensL is a registered trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
ON Semiconductor Website: www.onsemi.com
◊
www.onsemi.com
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明