MOC3073SR2M [ONSEMI]
三端双向可控硅开关驱动器光耦合器,6 引脚 DIP 随机相(峰值 800 V);型号: | MOC3073SR2M |
厂家: | ONSEMI |
描述: | 三端双向可控硅开关驱动器光耦合器,6 引脚 DIP 随机相(峰值 800 V) 开关 驱动 三端双向交流开关 输出元件 光电 可控硅开关 驱动器 |
文件: | 总15页 (文件大小:519K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
MOC3071M, MOC3072M
6-Pin DIP Random-Phase Triac
Driver Optocoupler (800 Volt Peak)
The MOC3071M and MOC3072M consist of a GaAs infrared emitting
diode optically coupled to a non-zero- crossing silicon bilateral AC switch
(triac). These devices isolate low voltage logic from 240 VAC lines to
provide random phase control of high current triacs or thyristors. These
devices feature greatly enhanced static dv/dt capability to ensure stable
switching performance of inductive loads.
www.onsemi.com
Features
Excellent IFT Stability—IR Emitting Diode Has Low Degradation
800 V Peak Blocking Voltage
Safety and RegulatoryApprovals
– UL1577, 4,170 VACRMS for 1 Minute
– DIN EN/IEC60747-5-5 (pending approval)
MDIP 6L WHITE
MARKING DIAGRAM
Typical Applications
Solenoid/ValveControls
Lamp Ballasts
Static AC Power Switch
Interfacing Microprocessors to 240 VAC Peripherals
Solid State Relay
1. F
= Fairchild Logo
2. MOC3071 =Specific Device Code
3. V
4. X
5. YY
6. Q
=DIN EN/IEC60747-5-5 Option
Incandescent Lamp Dimmers
Temperature Controls
=One-Digit Year Code
=Two-Digit Work Week
=Assembly Package Code
Motor Controls
PIN CONNECTIONS
ORDERING INFORMATION
See detailed ordering and shipping information page 9 of
this data sheet.
© Semiconductor Components Industries, LLC, 2016
November 2016 - Rev. 1
1
Publication Order Number:
MOC3071M/D
MOC3071M, MOC3072M
SAFETY AND INSULATIONS RATINGS
As per DIN EN/IEC 60747-5-5 (pending approval), this optocoupler is suitable for “safe electrical insulation” only within the safety limit data.
Compliance with the safety ratings shall be ensured by means of protective circuits.
Parameter
Characteristics
< 150 V
< 300 V
I–IV
I–IV
RMS
RMS
Installation Classifications per DIN VDE 0110/1.89 Table 1,
For Rated Mains Voltage
Climatic Classification
40/85/21
2
Pollution Degree (DIN VDE 0110/1.89)
Comparative Tracking Index
175
Symbol
Parameter
Input-to-Output Test Voltage, Method A, V
Value
Unit
x 1.6 = V , Type and
PR
IORM
Sample Test with t = 10 s, Partial Discharge < 5 pC
V
V
1360
1594
peak
peak
m
V
PR
Input-to-Output Test Voltage, Method B, V
x 1.875 = V , 100%
PR
IORM
Production Test with t = 1 s, Partial Discharge < 5 pC
m
V
V
V
Maximum Working Insulation Voltage
Highest Allowable Over-Voltage
850
6000
≥ 7
IORM
peak
peak
V
IOTM
External Creepage
mm
mm
mm
mm
Ω
External Clearance
≥ 7
External Clearance (for Option TV, 0.4" Lead Spacing)
Distance Through Insulation (Insulation Thickness)
Insulation Resistance at T , V = 500 V
≥ 10
≥ 0.5
DTI
9
R
> 10
S
IO
IO
www.onsemi.com
2
MOC3071M, MOC3072M
MAXIMUM RATINGS (Note 1)
T
= 25°C unless otherwise specified.
A
Symbol
Parameters
Value
Unit
Total Device
T
Storage Temperature
-40 to +150
-40 to +85
-40 to +100
260 for 10 seconds
330
°C
°C
STG
T
Operating Temperature
Junction Temperature Range
Lead Solder Temperature
OPR
T
J
°C
T
°C
SOL
Total Device Power Dissipation at 25°C Ambient
Derate Above 25°C
mW
mW/°C
P
D
4.4
Emitter
I
Continuous Forward Current
Reverse Voltage
60
3
mA
V
F
V
R
Total Power Dissipation at 25°C Ambient
Derate Above 25°C
100
1.33
mW
P
D
mW/°C
Detector
V
Off-State Output Terminal Voltage
800
1
V
A
DRM
I
Peak Non-Repetitive Surge Current (Single Cycle 60 Hz Sine Wave)
Total Power Dissipation at 25°C Ambient
Derate Above 25°C
TSM
300
4
mW
mW/°C
P
D
1. Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device
functionality should not be assumed, damage may occur and reliability may be affected.
www.onsemi.com
3
MOC3071M, MOC3072M
ELECTRICAL CHARACTERISTICS
T
= 25°C unless otherwise specified.
A
INDIVIDUAL COMPONENT CHARACTERISTICS
Symbol
Parameters
Test Conditions
Min.
Typ.
Max.
Unit
EMITTER
V
F
I
= 10 mA
= 3 V
Input Forward Voltage
1.18
0.05
1.50
100
V
F
I
V
Reverse Leakage Current
µA
R
R
DETECTOR
I
Peak Blocking Current, Either Direction
Peak On-State Voltage, Either Direction
Critical Rate of Rise of Off-State Voltage
10
200
2.5
nA
V
V
I
= 800 V, I = 0 (Note 2)
F
DRM
DRM
= 100 mA peak, I = 0
V
2.2
TM
TM
F
I
= 0, V
= 800 V)
DRM
dv/dt
1000
V/µs
F
TRANSFER CHARACTERISTICS
Symbol
DC Characteristics
Test Conditions
Device
Min.
Typ.
Max.
15
Unit
mA
µA
MOC3071M
MOC3072M
All
Main Terminal
Voltage = 3 V (Note 3)
I
LED Trigger Current, Either Direction
Holding Current, Either Direction
FT
10
I
540
H
ISOLATION CHARACTERISTICS
Symbol
Characteristic
Test Conditions
Min.
Typ.
Max.
Unit
V
Input-Output Isolation Voltage (Note 4) f = 60 Hz, t = 1 Minute
4170
VACRMS
ISO
11
R
V
= 500 VDC
Isolation Resistance
Isolation Capacitance
Ω
ISO
I-O
10
C
V = 0 V, f = 1 MHz
0.2
pF
ISO
2. Test voltage must be applied within dv/dt rating.
3. All devices are guaranteed to trigger at an I value less than or equal to max I . Therefore, the recommended operating I lies between
F
FT
F
maximum I (15 mA for MOC3071M, 10 mA for MOC3072M) and absolute maximum I (60 mA).
FT
F
4. Isolation voltage, V
common.
, is an internal device dielectric breakdown rating. For this test, pins 1 and 2 are common, and pins 4, 5 and 6 are
ISO
www.onsemi.com
4
MOC3071M, MOC3072M
TYPICAL CHARACTERISTICS
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
400
300
200
100
0
TA = -40 °C
-100
-200
-300
TA = 25 °C
TA = 100 °C
-400
-3
-2
-1
0
1
2
3
1
10
IF - LED FORWARD CURRENT (mA)
100
VTM - ON-STATE VOLTAGE (V)
Figure 1. LED Forward Voltage vs. Forward Current
Figure 2. On-State Characteristics
1.4
15
10
5
NORMALIZED TO TA = 25°C
NORMALIZED TO PW = 100µs
1.2
1.0
0.8
0.6
0
1
10
100
-40
-20
0
20
40
60
80
100
PW - LED TRIGGER PULSE WIDTH (µs)
TA - AMBIENT TEMPERATURE (°C)
Figure 3. LED Trigger Current vs. Ambient Temperature
Figure 4. LED Trigger Current vs. LED Pulse Width
4
10000
NORMALIZED TO TA = 25°C
VDRM = 800 V
1000
100
10
3
2
1
0
1
0.1
-40
-40
-20
0
20
40
60
80
100
-20
0
20
40
60
80
100
TA - AMBIENT TEMPERATURE (°C)
TA - AMBIENT TEMPERATURE (°C)
Figure 5. Holding Current vs. Ambient Temperature
Figure 6. Leakage Current vs. Ambient Temperature
www.onsemi.com
5
MOC3071M, MOC3072M
APPLICATIONS INFORMATION
Basic Triac Driver Circuit
LED Trigger Current vs. Pulse Width
The random phase triac drivers MOC3071M and
MOC3072M can allow snubberless operations in
applications where load is resistive and the external
generated noise in the AC line is below its guaranteed
dv/dt withstand capability. For these applications, a
snubber circuit is not necessary when a noise insensitive
power triac is used. Figure 7 shows the circuit diagram.
The triac driver is directly connected to the triac main
terminal 2 and a series resistor R which limits the current
to the triac driver. Current limiting resistor R must have a
minimum value which restricts the current into the driver
to maximum 1 A.
Random phase triac drivers are designed to be phase
controllable. They may be triggered at any phase angle
within the AC sine wave. Phase control may be
accomplished by an AC line zero cross detector and a
variable pulse delay generator which is synchronized to
the zero cross detector. The same task can be
accomplished by a microprocessor which is synchronized
to the AC zero crossing. The phase controlled trigger
current may be a very short pulse which saves energy
delivered to the input LED. LED trigger pulse currents
shorter than 100 µs must have increased amplitude as
shown on Figure 4. This graph shows the dependency of
the trigger current IFT versus the pulse width. IFT in this
graph is normalized in respect to the minimum specified
IFT for static condition, which is specified in the device
characteristic. The normalized IFT has to be multiplied
with the devices guaranteed static trigger current.
Example:
The power dissipation of this current limiting resistor and
the triac driver is very small because the power triac
carries the load current as soon as the current through
driver and current limiting resistor reaches the trigger
current of the power triac. The switching transition times
for the driver is only one micro second and for power
triacs typical four micro seconds.
IFT = 10 mA, Trigger PW = 4 µs
IF (pulsed) = 10 mA x 3 = 30 mA
Triac Driver Circuit for Noisy Environments
When the transient rate of rise and amplitude are expected
to exceed the power triacs and triac drivers maximum
ratings a snubber circuit as shown in Figure 8 is
recommended. Fast transients are slowed by the R-C
snubber and excessive amplitudes are clipped by the Metal
Oxide Varistor MOV.
Minimum LED Off Time in Phase Control Applications
In phase control applications, one intends to be able to
control each AC sine half wave from 0° to 180°. Turn on
at 0° means full power and turn on at 180° means zero
power. This is not quite possible in reality because triac
driver and triac have a fixed turn on time when activated
at zero degrees. At a phase control angle close to 180°the
driver’s turn on pulse at the trailing edge of the AC sine
wave must be limited to end 200 µs before AC zero cross
as shown in Figure 10. This assures that the triac driver has
time to switch off. Shorter times may cause loss of control
at the following half cycle.
Triac Driver Circuit for Extremely Noisy Environments
As specified in the noise standards IEEE472 and IEC255-
4.
Industrial control applications do specify a maximum
transient noise dv/dt and peak voltage which is super-
imposed onto the AC line voltage. In order to pass this
environment noise test a modified snubber network as
shown in Figure 9 is recommended.
Static dv/dt
Critical rate of rise of off-state voltage or static dv/dt is a
triac characteristic that rates its ability to prevent false
triggering in the event of fast rising line voltage transients
when it is in the off-state. When driving a discrete power
triac, the triac driver optocoupler switches back to off-
state once the power triac is triggered. However, during
the commutation of the power triac in application where
the load is inductive, both triacs are subjected to fast rising
voltages. The static dv/dt rating of the triac driver
optocoupler and the commutating dv/dt rating of the
power triac must be taken into consideration in snubber
circuit design to prevent false triggering and commutation
failure.
LED Trigger Current versus Temperature
Recommended operating LED control current IF lies
between the guaranteed IFT and absolute maximum IF.
Figure 3 shows the increase of the trigger current when the
device is expected to operate at an ambient temperature
below 25°C. Multiply the datasheet guaranteed IFT with
the normalized IFT shown on this graph and an allowance
for LED degradation over time.
Example:
IFT = 10 mA, LED degradation factor = 20%
IF at -40°C = 10 mA x 1.25 x 120% = 15 mA
www.onsemi.com
6
MOC3071M, MOC3072M
TRIAC DRIVER
VCC
RLED
R
POWER TRIAC
AC LINE
CONTROL
RET.
Q
LOAD
RLED = (VCC – VFLED – VSATQ) / IFT
R = VPAC / ITSM
Figure 7. Basic Driver Circuit
TRIAC DRIVER
VCC
RLED
R
POWER TRIAC
RS
CS
AC LINE
MOV
CONTROL
RET.
Q
LOAD
Typical Snubber values RS = 33 W, CS = 0.01 µF
MOV (Metal Oxide Varistor) protects power triac and
driver from transient overvoltages > VDRM max
Figure 8. Triac Driver Circuit for Noisy Environments
POWER TRIAC
TRIAC DRIVER
R
VCC
RLED
RS MOV
AC LINE
CS
CONTROL
RET.
Q
LOAD
Recommended snubber to pass IEEE472 and IEC255-4 noise tests
RS = 47 W, CS = 0.01 µF
Figure 9. Triac Driver Circuit for Extremely Noisy Environments
AC Line
0°
180°
LED PW
LED Current
LED turn off min. 200µs
Figure 10. Minimum Time for LED Turn Off to Zero Crossing
www.onsemi.com
7
MOC3071M, MOC3072M
REFLOW PROFILE
Profile Feature
Pb-Free Assembly Profile
150°C
Temperature Minimum (Tsmin)
Temperature Maximum (Tsmax)
200°C
Time (t ) from (Tsmin to Tsmax)
S
60 seconds to 120 seconds
3°C/second maximum
217°C
Ramp-up Rate (T to T )
L
P
Liquidous Temperature (T )
L
Time (t ) Maintained Above (T )
60 seconds to 150 seconds
260°C +0°C / –5°C
30 seconds
L
L
Peak Body Package Temperature
Time (t ) within 5°C of 260°C
P
Ramp-down Rate (T to T )
6°C/second maximum
8 minutes maximum
P
L
Time 25°C to Peak Temperature
Figure 11. Reflow Profile
www.onsemi.com
8
MOC3071M, MOC3072M
ORDERING INFORMATION (Note 5)
Device
Package
Shipping
Tube (50 Units)
MOC3071M
DIP 6-Pin
SMT 6-Pin (Lead Bend)
MOC3071SM
Tube (50 Units)
MOC3071SR2M
MOC3071VM
SMT 6-Pin (Lead Bend)
Tape and Reel (1000 Units)
DIP 6-Pin, DIN EN/IEC60747-5-5 Option (pending approval)
Tube (50 Units)
Tube (50 Units)
SMT 6-Pin (Lead Bend), DIN EN/IEC60747-5-5 Option (pending
approval)
MOC3071SVM
MOC3071SR2VM
MOC3071TVM
SMT 6-Pin (Lead Bend), DIN EN/IEC60747-5-5 Option (pending
approval)
Tape and Reel (1000 Units)
Tube (50 Units)
DIP 6-Pin, 0.4” Lead Spacing, DIN EN/IEC60747-5-5 Option (pending
approval)
5. The product orderable part number system listed in this table also applies to the MOC3072M product families.
www.onsemi.com
9
MOC3071M, MOC3072M
PACKAGING DIMENSIONS
8.89
8.13-8.89
6
4
7.62 (TYP)
PIN 1
1
3
15.0° (TYP)
0.20-0.30
0.25-0.36
NOTES:
A)
NO STANDARD APPLIES TO THIS PACKAGE.
B) ALL DIMENSIONS ARE IN MILLIMETERS.
DIMENSIONS ARE EXCLUSIVE OF BURRS,
MOLD FLASH, AND TIE BAR EXTRUSION
D) DRAWING FILENAME AND REVSION: MKT-N06BREV4.
C)
0.38 (MIN)
(0.86)
2.54 BSC
0.41-0.51
1.02-1.78
0.76-1.14
6 LEAD MDIP OPTO WHITE 0.3" WIDE
www.onsemi.com
10
MOC3071M, MOC3072M
8.13-8.89
(1.52)
(1.78)
(2.54)
6
4
1
3
(0.76)
LAND PATTERN RECOMMENDATION
PIN 1
5.08 (MAX)
3.28-3.53
0.38 (MIN)
0.25-0.36
0.20-0.30
2.54 (BSC)
0.16-0.88
(8.13)
(0.86)
0.41-0.50
1.02-1.78
0.76-1.14
NOTES:
A)
NO STANDARD APPLIES TO THIS PACKAGE.
B) ALL DIMENSIONS ARE IN MILLIMETERS.
DIMENSIONS ARE EXCLUSIVE OF BURRS,
MOLD FLASH, AND TIE BAR EXTRUSION
C)
D) DRAWING FILENAME AND REVSION : MKT-N06CREV4.
6-LEAD MDIP OPTO WHITE SURFACE MOUNT FORM
www.onsemi.com
11
MOC3071M, MOC3072M
8.13-8.89
6
4
0.20-0.30
10.16-10.80
PIN 1
1
3
0.25-0.36
NOTES:
A)
NO STANDARD APPLIES TO THIS PACKAGE.
B) ALL DIMENSIONS ARE IN MILLIMETERS.
DIMENSIONS ARE EXCLUSIVE OF BURRS,
MOLD FLASH, AND TIE BAR EXTRUSION
D) DRAWING FILENAME AND REVSION: MKT-N06Drev4
C)
0.38 (MIN)
(0.86)
0.41-0.51
1.02-1.78
0.76-1.14
2.54 BSC
6 LEAD MDIP OPTO WHITE 0.4" LEAD SPACING
www.onsemi.com
12
MOC3071M, MOC3072M
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States
and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON
Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further
notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON
Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special,
consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and
safety
requirements
or
standards,
regardless
of
any
support
or
applications
information
provided
by
ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor
does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in
life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in
the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON
Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising
out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was
negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright
laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303-675-2175 or 800-344-3860 Toll Free
USA/Canada
N. American Technical Support: 800-282-
9855 Toll Free
ON Semiconductor Website:
www.onsemi.com
USA/Canada.
Europe, Middle East and Africa Technical
Support:
Order Literature:
Fax: 303-675-2176 or 800-344-3867 Toll Free
USA/Canada
http://www.onsemi.com/orderlit
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81-3-5817-1050
Email: orderlit@onsemi.com
For additional information, please contact
your local
Sales Representative
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
© Semiconductor Components Industries, LLC
www.onsemi.com
相关型号:
MOC3080-G
Optocoupler - Trigger Device Output, 1 CHANNEL TRIAC OUTPUT WITH ZERO CRSVR OPTOCOUPLER, ROHS COMPLIANT, DIP-6
ISOCOM
MOC3080-SMT&R
Triac Output Optocoupler With Zero CRSVR, 1-Element, 5300V Isolation, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-6
ISOCOM
MOC3080SM
Triac Output Optocoupler With Zero CRSVR, 1-Element, 5300V Isolation, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-6
ISOCOM
MOC3080SMT&R
Triac Output Optocoupler With Zero CRSVR, 1-Element, 5300V Isolation, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-6
ISOCOM
MOC3080X
Triac Output Optocoupler With Zero CRSVR, 1-Element, 5300V Isolation, ROHS COMPLIANT, DIP-6
ISOCOM
MOC3080X-G
Optocoupler - Trigger Device Output, 1 CHANNEL TRIAC OUTPUT WITH ZERO CRSVR OPTOCOUPLER, ROHS COMPLIANT, DIP-6
ISOCOM
MOC3080X-SM
Optocoupler - Trigger Device Output, 1 CHANNEL TRIAC OUTPUT WITH ZERO CRSVR OPTOCOUPLER, ROHS COMPLIANT, SURFACE MOUNT, DIP-6
ISOCOM
MOC3080X-SMT&R
Optocoupler - Trigger Device Output, 1 CHANNEL TRIAC OUTPUT WITH ZERO CRSVR OPTOCOUPLER, ROHS COMPLIANT, SURFACE MOUNT, DIP-6
ISOCOM
MOC3080XSM
Triac Output Optocoupler With Zero CRSVR, 1-Element, 5300V Isolation, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-6
ISOCOM
©2020 ICPDF网 联系我们和版权申明