NCP1342ADDCDAD1R2G_技术文档

NCP1342

High Frequency Quasi-

Resonant Flyback Controller

The NCP1342 is a highly integrated quasi−resonant flyback

controller suitable for designing high−performance off−line power

converters. With an integrated active X2 capacitor discharge feature,

the NCP1342 can enable no−load power consumption below 30 mW.

The NCP1342 features a proprietary valley−lockout circuitry,

www.onsemi.com

th

ensuring stable valley switching. This system works down to the 6

valley and transitions to frequency foldback mode to reduce switching

losses. As the load decreases further, the NCP1342 enters quiet−skip

mode to manage the power delivery while minimizing acoustic noise.

To ensure light load performance with high frequency designs, the

NCP1342 incorporates Minimum Peak Current Modulation (MPCM)

to reduce the switching frequency quickly. To help ensure converter

ruggedness, the NCP1342 implements several key protective features

such as internal brownout detection, a non−dissipative Over Power

Protection (OPP) for constant maximum output power regardless of

input voltage, a latched overvoltage and NTC−ready overtemperature

protection through a dedicated pin, and line removal detection to safely

discharge the X2 capacitors when the ac line is removed. If transient

load capability is desired, the NCP1343 offers the same performance

and features with the addition of power excursion mode (PEM).

8

9

1

SOIC−9 NB

D SUFFIX

CASE 751BP

SOIC−8 NB

D SUFFIX

CASE 751

MARKING DIAGRAMS

8

9

1

1342abcde

ALYW

G

1

Features

1342abcde = Specific Device Code

A

L

Y

W

G

= Assembly Location

= Wafer Lot

= Year

= Work Week

= Pb−Free Package

• Integrated High−Voltage Startup Circuit with Brownout Detection

• Integrated X2 Capacitor Discharge Capability

• Wide V Range from 9 V to 28 V

CC

• 28 V V Overvoltage Protection

CC

• Abnormal Overcurrent Fault Protection for Winding Short Circuit or

Saturation Detection

PIN CONNECTIONS

• Internal Temperature Shutdown

1

Fault

HV

• Valley Switching Operation with Valley−Lockout for Noise−Free

FMAX

FB

ZCD/OPP

CS

Operation

VCC

DRV

GND

• Frequency Foldback with 25 kHz Minimum Frequency Clamp for

Increased Efficiency at Light Loads

• MPCM for Fast Reduction of Switching Frequency at Light Loads

1

HV

Fault

FB

• Skip Mode with Quiet−Skip Technology for Highest Performance

VCC

During Light Loads

DRV

GND

ZCD/OPP

CS

• Minimized Current Consumption for No Load Power Below 30 mW

• Frequency Jittering for Reduced EMI Signature

(Top Views)

• Latching or Auto−Recovery Timer−Based Overload Protection

• Adjustable Overpower Protection (OPP)

ORDERING INFORMATION

See detailed ordering and shipping information on page 3 of

• Adjustable Maximum Frequency Clamp

• Fault Pin for Severe Fault Conditions, NTC Compatible for OTP

• 4 ms Soft−Start Timer

this data sheet.

1

Publication Order Number:

December, 2017 − Rev. 1

NCP1342/D

NCP1342

TYPICAL APPLICATION SCHEMATIC

Vout

+

NCP1342

Fault

HV

+

FB

VCC

L

EMI

Filter

ZCD/OPP DRV

CS

GND

N

+

−tº

Figure 1. NCP1342 8−Pin Typical Application Circuit

Vout

+

NCP1342

Fault

HV

FMAX

+

FB

VCC

L

EMI

Filter

ZCD/OPP DRV

CS

GND

N

+

−tº

Figure 2. NCP1342 9−Pin Typical Application Circuit

www.onsemi.com

2

NCP1342

Table 1. PART NUMBER DECODE − NCP1342ABCDEFR2G

NCP1342

A

B

C

D

E

F*

R2G*

OTP/Overload

A − AR/AR

Jitter Frequency/Amplitude

A − 1.55 kHz/75 mV

B − 1.55 kHz/92 mV

C − 1.55 kHz/55 mV

D − 1.55 kHz/61 mV

E − 1.3 kHz/75 mV

F − 1.3 kHz/92 mV

G − 1.3 kHz/55 mV

H − 1.3 kHz/61 mV

J − 3.9 kHz/75 mV

K − 3.9 kHz/92 mV

L − 3.9 kHz/55 mV

M − 3.9 kHz/61 mV

N − Disabled

Quiet−Skip

A − 800 Hz

B − 1.2 kHz

C − 1.56 kHz

D − Disabled

CS Min

MPCM

Pins

A − 200 mV

B − 150 mV

C − 100 mV

D − 250 mV

A − 400 mV

B − 350 mV

C − 300 mV

D − 250 mV

E − Disabled

D − 8 Pins

D1 − 9 Pins

B − Latch/AR

C − AR/Latch

D − Latch/Latch

Pb

Free

Device

*In OPN only − not on device marking

Table 2. ORDERING INFORMATION

Part Number

Device Marking

Package

Shipping

NCP1342BLACADR2G

NCP1342AMDAAD1R2G

NCP1342DADBDD1R2G

1342BLACA

1342AMDAA

1342DADBD

SOIC−8 NB (Pb−Free)

2500 / Tape & Reel

SOIC−9 NB (Pb−Free)

www.onsemi.com

3

NCP1342

FUNCTIONAL BLOCK DIAGRAM

TSD

BO

X2/BO Detect

+

V

DD

HV

X2

Abnormal OCP

OVLD

V

Fault

CC

CC(OVP)

FMAX

Control

Management

OVP

OTP

Management

FMAX

QR_FMAX

VCC

Valley/FF

Control

FB

Fault

Off−Time

Control

Dead−Time

Control

ZCD/OPP

OPP

Control

V

CC

t

QR_FMAX

tout

Clamp

V

OPP

FB(open)

R

Quiet−Skip

Control

FB

S

R

Q

FB

DRV

GND

Jitter Ramp

K

FB

CS

÷

MPCM

Control

On−Time

Control

FB

V

DD

Fault

V

DD

OVP

OTP

OVP/OTP

Detect

Fault

ILIM1

Detect

t

OVLD

LEB1

R

Fault(clamp)

OPP

V

Fault(clamp)

ILIM2

Detect

t

Abnormal OCP

Count 4

LEB2

8−Pin

9−Pin

Figure 3. NCP1342 Block Diagram

Table 3. PIN FUNCTIONAL DESCRIPTION

8−Pin

9−Pin

Pin Name

Function

1

Fault

The controller enters fault mode if the voltage on this pin is pulled above or below the fault

thresholds. A precise pull up current source allows direct interface with an NTC thermistor.

−

2

FMAX

A resistor to ground sets the value for the maximum switching frequency clamp. If this pin is

pulled above 4 V, the maximum frequency clamp is disabled.

2

3

4

FB

Feedback input for the QR Flyback controller. Allows direct connection to an optocoupler.

ZCD/OPP

A resistor divider from the auxiliary winding to this pin provides input to the demagnetization de-

tection comparator and sets the OPP compensation level.

4

5

6

5

6

7

CS

Input to the cycle−by−cycle current limit comparator.

Ground reference.

GND

DRV

This is the drive pin of the circuit. The DRV high−current capability (−0.5 /+0.8 A) makes it suit-

able to effectively drive high gate charge power MOSFETs.

7

8

VCC

This pin is the positive supply of the IC. The circuit starts to operate when V exceeds 17 V and

CC

turns off when V goes below 9 V (typical values). After start−up, the operating range is 9 V up

CC

to 28 V.

−

8

9

N/C

HV

Removed for creepage distance.

10

This pin is the input for the high voltage startup and brownout detection circuits. It also contains

the line removal detection circuit to safely discharge the X2 capacitors when the line is removed.

www.onsemi.com

4

NCP1342

Table 4. MAXIMUM RATINGS

Rating

Symbol

Value

Unit

V

High Voltage Startup Circuit Input Voltage

High Voltage Startup Circuit Input Current

Supply Input Voltage

V

−0.3 to 700

HV(MAX)

I

20

mA

V

−0.3 to 30

CC(MAX)

Supply Input Current

I

30

1

mA

V/ms

V

Supply Input Voltage Slew Rate

Fault Input Voltage

dV /dt

CC

V

−0.3 to V + 0.7 V

Fault(MAX)

CC

Fault Input Current

I

10

mA

V

Zero Current Detection and OPP Input Voltage

Zero Current Detection and OPP Input Current

Maximum Input Voltage (Other Pins)

Maximum Input Current (Other Pins)

Driver Maximum Voltage (Note 1)

Driver Maximum Current

V

−0.3 to V + 0.7 V

ZCD(MAX)

CC

I

−2/+5

−0.3 to 5.5

10

mA

V

ZCD(MAX)

V

MAX

I

mA

V

MAX

V

DRV

−0.3 to V

DRV(high)

I

500

mA

DRV(SRC)

I

800

DRV(SNK)

Operating Junction Temperature

Storage Temperature Range

T

−40 to 125

–60 to 150

°C

J

T

STG

2

Power Dissipation (T = 25°C, 1 oz. Cu, 42 mm Copper Clad Printed Circuit)

P

mW

A

D(MAX)

DR2G Suffix, SOIC−8

D1R2G Suffix, SOIC−9

450

330

2

Thermal Resistance (T = 25°C, 1 oz. Cu, 42 mm Copper Clad Printed Circuit)

R

°C/W

A

qJA

DR2G Suffix, SOIC−8

D1R2G Suffix, SOIC−9

225

300

ESD Capability

Human Body Model per JEDEC Standard JESD22−A114F (All pins except HV)

Human Body Model per JEDEC Standard JESD22−A114F (HV Pin)

Charge Device Model per JEDEC Standard JESD22−C101F

Latch−Up Protection per JEDEC Standard JESD78E

2000

800

1000

V

100

mA

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

1. Maximum driver voltage is limited by the driver clamp voltage, V

, when V

DRV(high)

exceeds the driver clamp voltage. Otherwise, the

CC

maximum driver voltage is V

.

CC

www.onsemi.com

5

NCP1342

Table 5. ELECTRICAL CHARACTERISTICS: (V = 12 V, V = 120 V, V

= open, V = 2.4 V, V = 0 V, V

= 0 V, V

CC

HV

Fault

FB

CS

ZCD FMAX

= 0 V, C

= 100 nF , C

= 100 pF, for typical values T = 25°C, for min/max values, T is – 40°C to 125°C, unless otherwise noted)

VCC

DRV

J

Characteristics

Conditions

Symbol

Min

Typ

Max

Unit

START−UP AND SUPPLY CIRCUITS

Supply Voltage

dV/dt = 0.1 V/ms

V

Startup Threshold

V

increasing

decreasing

V

16.0

17.0

8.5

17.0

18.0

9.0

–

18.0

19.0

9.5

–

CC

CC(on)

Discharge Voltage During Line Removal

Minimum Operating Voltage

Operating Hysteresis

V

CC(X2_reg)

V

CC(off)

V

CC(on)

− V

V

7.5

CC(off)

CC(HYS)

CC(reset)

CC(inhibit)

Internal Latch / Logic Reset Level

V

CC

decreasing

V

4.5

6.5

0.70

7.5

1.05

Transition from I

to I

V

CC

increasing, I = 650 mA

V

0.30

start1

start2

HV

V

Delay

V

decreasing

t

delay(VCC_off)

25

–

32

–

40

500

40

ms

V

CC(off)

CC

Startup Delay

Delay from V

to DRV Enable

t

delay(start)

CC(on)

Minimum Voltage for Start−Up Current

Source

V

–

HV(MIN)

Inhibit Current Sourced from V Pin

V

= 0 V

I

0.2

2.4

0.5

0.65

5.0

mA

CC

cc

start1

Start−Up Current Sourced from V Pin

V

= V – 0.5 V

cc(on)

3.75

CC

cc

start2

Start−Up Circuit Off−State Leakage Current

V

= 162.5 V

I

–

15

20

50

HV

HV(off1)

HV(off2)

HV(off3)

V

= 325 V

= 700 V

HV

V

Supply Current

mA

Fault or Latch

V

= V

– 0.5 V

I

−

0.115

0.230

1.0

0.150

0.315

1.5

CC

CC(on)

CC1

CC2

CC3

Skip Mode (excluding FB current)

Operating Current

V

FB

= 0 V

f

= 50 kHz, C

= open

sw

DRV

V

CC

V

CC

Overvoltage Protection Threshold

Overvoltage Protection Delay

V

27

25

28

32

29

40

V

CC(OVP)

t

ms

delay(VCC_OVP)

X2 CAPACITOR DISCHARGE

Line Voltage Removal Detection Timer

Discharge Timer Duration

t

65

21

13

–

100

32

18

–

135

43

23

30

ms

mA

V

line(removal)

t

line(discharge)

Line Detection Timer Duration

t

line(detect)

V

CC

Discharge Current

V

= 20 V

I

CC

CC(discharge)

HV Discharge Level

BROWNOUT DETECTION

System Start−Up Threshold

Brownout Threshold

Hysteresis

V

HV(discharge)

V

increasing

decreasing

increasing

decreasing

V

107

93

112

98

116

102

–

V

HV

BO(start)

BO(stop)

BO(HYS)

BO(stop)

V

HV

V

9.0

40

14

V

HV

Brownout Detection Blanking Time

GATE DRIVE

V

t

70

100

ms

Rise Time

V

from 10% to 90%

from 90% to 10%

t

–

20

5

40

30

ns

DRV

DRV(rise)

Fall Time

V

DRV

t

DRV(fall)

Current Capability

Source

mA

I

–

500

800

–

DRV(SRC)

Sink

I

DRV(SNK)

High State Voltage

V

CC

= V

V

+ 0.2 V, R

= 10 kW

V

8.0

10

–

V

CC(off)

DRV

DRV(high1)

12

14

= 30 V, R

= 10 kW

DRV(high2)

CC

DRV

Low Stage Voltage

V

= 0 V

V

–

0.25

Fault

DRV(low)

2. NTC with R110 = 8.8 kW

www.onsemi.com

6

NCP1342

Table 5. ELECTRICAL CHARACTERISTICS: (V = 12 V, V = 120 V, V

= open, V = 2.4 V, V = 0 V, V

= 0 V, V

CC

HV

Fault

FB

CS

ZCD FMAX

= 0 V, C

= 100 nF , C

= 100 pF, for typical values T = 25°C, for min/max values, T is – 40°C to 125°C, unless otherwise noted)

VCC

DRV

J

Characteristics

Conditions

Symbol

Min

Typ

Max

Unit

FEEDBACK

Open Pin Voltage

to Internal Current Setpoint Division

V

4.8

−

5.0

4

5.1

−

V

–

FB(open)

V

FB

K

FB

Ratio

Internal Pull−Up Resistor

V

FB

= 0.4 V

R

17

20

23

kW

FB

Valley Thresholds

V

st

nd

Transition from 1 to 2 valley

V

decreasing

increasing

V

1to2

V

2to3

V

3to4

V

4to5

V

5to6

V

6to5

V

5to4

V

4to3

V

3to2

V

2to1

1.316

1.128

1.034

0.940

0.846

1.410

1.504

1.598

1.692

1.880

1.400

1.200

1.100

1.000

0.900

1.500

1.600

1.700

1.800

2.000

1.484

1.272

1.166

1.060

0.954

1.590

1.696

1.802

1.908

2.120

FB

nd

rd

Transition from 2 to 3 valley

rd

th

Transition from 3 to 4 valley

th

Transition from 4 to 5 valley

th

Transition from 5 to 6 valley

th

Transition from 6 to 5 valley

V

FB

th

Transition from 5 to 4 valley

th

rd

Transition from 4 to 3 valley

rd

nd

Transition from 3 to 2 valley

nd

st

Transition from 2 to 1 valley

Maximum Frequency Clamp

kHz

V

FMAX

V

FMAX

= 0.5 V

= 3.5 V

f

440

61

500

70

560

79

MAX1

MAX2

FMAX Disable Threshold

FMAX Pin Source Current

Maximum On Time

9−Pin Versions Only

V

3.85

9.0

28

4.00

10

4.15

11

V

FMAX(disable)

I

mA

ms

FMAX

t

32

40

on(MAX)

DEMAGNETIZATION INPUT

ZCD threshold voltage

V

decreasing

increasing

V

35

15

–

60

25

80

90

55

mV

ns

ZCD

ZCD(trig)

ZCD hysteresis

V

ZCD(HYS)

ZCD

Demagnetization Propagation Delay

V

ZCD

step from 4.0 V to −0.3 V

t

250

demag

ZCD Clamp Voltage

Positive Clamp

Negative Clamp

V

I

= 5.0 mA

= −2.0 mA

V

12.4

−0.9

12.7

−0.7

13

0

QZCD

ZCD(MAX)

I

QZCD

ZCD(MIN)

Blanking Delay After Turn−Off

t

600

700

800

ns

ZCD(blank)

Timeout After Last Demagnetization

Detection

While in soft−start

After soft−start complete

t

80

5.1

100

6.0

120

6.9

ms

(tout1)

(tout2)

CURRENT SENSE

Current Limit Threshold Voltage

Leading Edge Blanking Duration

V

increasing

V

0.760

220

0.800

265

0.840

330

V

CS

ILIM1

DRV minimum width minus

t

ns

LEB1

t

delay(ILIM1)

Current Limit Threshold Propagation Delay

PWM Comparator Propagation Delay

Step V

0 V to V

+ 0.5 V,

t

delay(ILIM1)

–

95

175

ns

CS

ILIM1

V

FB

= 4 V

Step V

0 V to 0.7 V, V = 2.4

t

delay(PWM)

125

ns

CS

FB

Minimum Peak Current

Versions xxxAx

Versions xxxBx

Versions xxxCx

Versions xxxDx

V

mV

CS(MIN)

170

115

70

200

150

100

250

230

185

130

285

215

Abnormal Overcurrent Fault Threshold

V

increasing, V = 4 V

V

1.125

80

1.200

110

1.275

140

V

CS

FB

ILIM2

Abnormal Overcurrent Fault Blanking

Duration

DRV minimum width minus

t

ns

LEB2

t

delay(ILIM2)

2. NTC with R110 = 8.8 kW

www.onsemi.com

7

NCP1342

Table 5. ELECTRICAL CHARACTERISTICS: (V = 12 V, V = 120 V, V

= open, V = 2.4 V, V = 0 V, V

= 0 V, V

CC

HV

Fault

FB

CS

ZCD FMAX

= 0 V, C

= 100 nF , C

= 100 pF, for typical values T = 25°C, for min/max values, T is – 40°C to 125°C, unless otherwise noted)

VCC

DRV

J

Characteristics

Conditions

Symbol

Min

Typ

Max

Unit

CURRENT SENSE

Abnormal Overcurrent Fault Propagation

Delay

Step V

0 V to V

+ 0.5 V,

t

–

80

4

175

–

ns

CS

ILIM2

delay(ILIM2)

V

FB

= 4 V

Number of Consecutive Abnormal Overcur-

rent Faults to Enter Latch Mode

n

ILIM2

Overpower Protection Delay

V

dv/dt = 1 V/ms, measured from

t

95

175

ns

CS

OPP(delay)

V

to DRV falling edge

OPP(MAX)

Overpower Signal Blanking Delay

Pull−Up Current Source

JITTERING

t

220

0.7

280

1.0

330

1.5

ns

OPP(blank)

V

CS

= V

− 10 mV

I

CS

mA

ILIM2

Jitter Frequency

f

kHz

mV

jitter

Versions xJxxx, xKxxx, xLxxx, xMxxx

Versions xAxxx, xBxxx, xCxxx, xDxxx

Versions xExxx, xFxxx, xGxxx, xHxxx

Versions xNxxx

3.5

1.43

1.2

−

3.9

1.55

1.3

−

4.2

1.68

1.4

−

Peak Jitter Voltage

V

jitter

Versions xBxxx, xFxxx, xKxxx

Versions xAxxx, xExxx, xJxxx

Versions xDxxx, xHxxx, xMxxx

Versions xCxxx, xGxxx, xLxxx

Versions xNxxx

82

65

52

45

−

92

75

61

55

−

102

85

70

65

−

FAULT PROTECTION

Soft−Start Period

Measured from

DRV pulse to V = V

t

2.8

4.0

5.0

ms

SSTART

st

1

CS

ILIM1

Flyback Overload Fault Timer

Overvoltage Protection (OVP) Threshold

OVP Detection Delay

V

= V

t

OVLD

120

2.79

22.5

380

160

3.00

30

200

3.21

37.5

420

ms

V

CS

ILIM1

V

increasing

decreasing

V

Fault

Fault(OVP)

delay(OVP)

t

ms

Overtemperature Protection (OTP) Thresh-

old (Note 2)

V

400

mV

Fault(OTP_in)

Overtemperature Protection (OTP) Exiting

Threshold (Note 2)

V

increasing

V

880

910

940

mV

Fault

Fault(OTP_out)

Versions B Only

OTP Detection Delay

V

Fault

decreasing

t

22.5

30

37.5

ms

delay(OTP)

OTP Pull−Up Current Source

V

Fault

= V

+ 0.2 V

I

OTP

43.75

45.00

46.25

mA

Fault(OTP_in)

T = 25°C to 125°C

J

Fault Input Clamp Voltage

Fault Input Clamp Series Resistor

Autorecovery Timer

V

R

1.15

1.32

1.8

1.7

1.55

2.0

2.25

1.78

2.2

V

kW

s

Fault(clamp)

t

restart

LIGHT/NO LOAD MANAGEMENT

Minimum Frequency Clamp

f

21.5

32

25

−

27.0

−

kHz

MIN

Dead−Time Added During Frequency

Foldback

V

FB

= 400 mV

t

ms

DT(MAX)

Quiet−Skip Timer

Versions xxAxx

Versions xxBxx

Versions xxCxx

Versions xxDxx

t

ms

quiet

1.18

0.770

0.590

−

1.25

0.833

0.640

−

1.40

0.900

0.690

−

Skip Threshold

V

decreasing

increasing

V

350

20

400

50

450

70

mV

FB

skip

V

skip(HYS)

Skip Hysteresis

V

FB

2. NTC with R110 = 8.8 kW

www.onsemi.com

8

NCP1342

Table 5. ELECTRICAL CHARACTERISTICS: (V = 12 V, V = 120 V, V

= open, V = 2.4 V, V = 0 V, V

= 0 V, V

CC

HV

Fault

FB

CS

ZCD FMAX

= 0 V, C

= 100 nF , C

= 100 pF, for typical values T = 25°C, for min/max values, T is – 40°C to 125°C, unless otherwise noted)

VCC

DRV

J

Characteristics

Conditions

Symbol

Min

Typ

Max

Unit

MINIMUM PEAK CURRENT MODULATION (MPCM)

MPCM Current Shift

Versions xxxxA

Versions xxxxB

Versions xxxxC

Versions xxxxD

Versions xxxxE

V

mV

MPCM(delta)

340

300

250

200

−

400

350

300

250

−

460

400

350

300

−

MPCM Entry Threshold

Versions xxxxA, xxxxB, xxxxC, xxxxD

Versions xxxxE

V

mV

ms

MPCM(entry)

780

−

800

−

820

−

MPCM Exit Threshold

Versions xxxxA, xxxxB, xxxxC, xxxxD

Versions xxxxE

V

MPCM(exit)

730

−

750

−

770

−

MPCM Transition Timer

Versions xxxxA, xxxxB, xxxxC, xxxxD

Versions xxxxE

t

MPCM

0.85

−

1.00

−

1.05

−

THERMAL PROTECTION

Thermal Shutdown

Temperature increasing

Temperature decreasing

T

–

140

40

–

°C

SHDN

Thermal Shutdown Hysteresis

2. NTC with R110 = 8.8 kW

T

SHDN(HYS)

www.onsemi.com

9

NCP1342

INTRODUCTION

The NCP1342 implements a quasi−resonant flyback

two different valleys, which is often undesirable. The

NCP1342 patented VLO circuitry solves this issue by

determining the operating valley based on the system

load, and locking out other valleys unless a significant

change in load occurs.

converter utilizing current−mode architecture where the

switch−off event is dictated by the peak current. This IC is

an ideal candidate where low parts count and cost

effectiveness are the key parameters, particularly in ac−dc

adapters, open−frame power supplies, etc. The NCP1342

incorporates all the necessary components normally needed

in modern power supply designs, bringing several

enhancements such as non−dissipative overpower

protection (OPP), brownout protection, and frequency

reduction management for optimized efficiency over the

entire power range. Accounting for the needs of extremely

low standby power requirements, the controller features

minimized current consumption and includes an automatic

X2 capacitor discharge circuit that eliminates the need to

install power−consuming resistors across the X2 input

capacitors.

• High−Voltage Start−Up Circuit: Low standby power

consumption cannot be obtained with the classic

resistive start−up circuit. The NCP1342 incorporates a

high−voltage current source to provide the necessary

current during start−up and then turns off during normal

operation.

• Internal Brownout Protection: The ac input voltage is

sensed via the high−voltage pin. When this voltage is

too low, the NCP1342 stops switching. No restart

attempt is made until the ac input voltage is back within

its normal range.

• Frequency Foldback: As the load continues to

decrease, it becomes beneficial to reduce the switching

frequency. When the load is light enough, the NCP1342

enters frequency foldback mode. During this mode, the

minimum peak current is limited and dead−time is

added to the switching cycle, thus reducing the

frequency and switching operation to discontinuous

conduction mode (DCM). Dead−time continues to be

added until skip mode is reached, or the switching

frequency reaches its minimum level of 25 kHz.

• Minimum Peak Current Modulation (MPCM): In

order to reduce the switching frequency even faster (for

high frequency designs), the NCP1342 uses MPCM to

increase the minimum peak current during frequency

foldback. It also reduces the minimum peak current

gradually as the load decreases to ensure optimum skip

mode entry.

• Skip Mode: To further improve light or no−load power

consumption while avoiding audible noise, the

NCP1342 enters skip mode when the operating

frequency reaches its minimum value. To avoid

acoustic noise, the circuit prevents the switching

frequency from decaying below 25 kHz. This allows

regulation via bursts of pulses at 25 kHz or greater

instead of operating in the audible range.

• X2−Capacitor Discharge Circuitry: Per the

IEC60950 standard, the time constant of the X2 input

capacitors and their associated discharge resistors must

be less than 1 s in order to avoid electrical shock when

the user unplugs the power supply and inadvertently

touches the ac input cord terminals. By providing an

automatic means to discharge the X2 capacitors, the

NCP1342 eliminates the need to install X2 discharge

resistors, thus reducing power consumption.

• Quiet−Skip: To further reduce acoustic noise, the

NCP1342 incorporates a novel circuit to prevent the

skip mode burst period from entering the audible range

as well.

• Internal OPP: In order to limit power delivery at high

line, a scaled version of the negative voltage present on

the auxiliary winding during the on−time is routed to

the ZCD/OPP pin. This provides the designer with a

simple and non−dissipative means to reduce the

maximum power capability as the bulk voltage

increases.

• Frequency Jittering: In order to reduce the EMI

signature, a low frequency triangular voltage waveform

is added to the input of the PWM comparator. This

helps by spreading out the energy peaks during noise

analysis.

• Internal Soft−Start: The NCP1342 includes a 4 ms

soft−start to prevent the main power switch from being

overly stressed during start−up. Soft−start is activated

each time a new startup sequence occurs or during

auto−recovery mode.

• Quasi−Resonant, Current−Mode Operation:

Quasi−Resonant (QR) mode is a highly efficient mode

of operation where the MOSFET turn−on is

synchronized with the point where its drain−source

voltage is at the minimum (valley). A drawback of this

mode of operation is that the operating frequency is

inversely proportional to the system load. The

NCP1342 incorporates a valley lockout (VLO) and

frequency foldback technique to eliminate this

drawback, thus maximizing the efficiency over the

entire power range.

• Valley Lockout: In order to limit the maximum

frequency while remaining in QR mode, one would

traditionally use a frequency clamp. Unfortunately, this

can cause the controller to jump back and forth between

www.onsemi.com

10

NCP1342

is available disabled or fixed at 110 kHz. In the 9−pin

• Dedicated Fault Input: The NCP1342 includes a

dedicated fault input. It can be used to sense an

overvoltage condition and latch off the controller by

pulling the pin above the overvoltage protection (OVP)

threshold. The controller is also disabled if the Fault pin

is pulled below the overtemperature protection (OTP)

threshold. The OTP threshold is configured for use with

a NTC thermistor.

versions, the clamp can be adjusted via an external

resistor from the FMAX Pin to ground. It can also be

disabled by pulling the FMAX pin above 4 V.

HIGH VOLTAGE START−UP

The NCP1342 contains a multi−functional high voltage

(HV) pin. While the primary purpose of this pin is to reduce

standby power while maintaining a fast start−up time, it also

incorporates brownout detection and line removal detection.

The HV pin must be connected directly to the ac line in

order for the X2 discharge circuit to function correctly. Line

and neutral should be diode “ORed” before connecting to the

HV pin as shown in Figure 4. The diodes prevent the pin

voltage from going below ground. A resistor in series with

the pin should be used to protect the pin during EMC or surge

testing. A low value resistor should be used (<5 kW) to

reduce the voltage offset during start−up.

• Overload/Short−Circuit Protection: The NCP1342

implements overload protection by limiting the

maximum time duration for operation during overload

conditions. The overload timer operates whenever the

maximum peak current is reached. In addition to this,

special circuitry is included to prevent operation in

CCM during extreme overloads, such as an output

short−circuit.

• Maximum Frequency Clamp: The NCP1342 includes

a maximum frequency clamp. In all versions, the clamp

AC

CON

EMI

HV

Controller

Figure 4. High−Voltage Input Connection

Start−up and V_CCManagement

During start−up, the current source turns on and charges

the V capacitor with I (typically 6 mA). When V

Once V reaches V

the controller bias current increases to I (typically

, the controller is enabled and

CC

CC(on)

CC

start2

cc

CC3

reaches V

(typically 16.0 V), the current source turns

2.0 mA). However, the total bias current is greater than this

due to the gate charge of the external switching MOSFET.

CC(on)

off. If the input voltage is not high enough to ensure a proper

start−up (i.e. V has not reached V ), the controller

The increase in I due to the MOSFET is calculated using

HV

BO(start)

CC

will not start. V then begins to fall because the controller

Equation 1.

CC

bias current is at I

supply voltage is not present. When V falls to V

(typically 1 mA) and the auxiliary

DI_CC+ f_sw@ Q_G@ 10⁻³

(eq. 1)

CC2

CC

CC(off)

where DI is the increase in milliamps, f is the switching

(typically 10.5 V), the current source turns back on and

charges V . This cycle repeats indefinitely until V

CC

sw

frequency in kilohertz and Q is the gate charge of the

G

CC

HV

external MOSFET in nanocoulombs.

reaches V

. Once this occurs, the current source

BO(start)

C

VCC

must be sized such that a V voltage greater than

immediately turns on and charges V to V

, at which

CC(on)

CC

V

is maintained while the auxiliary supply voltage

point the controller starts (see Figure 6).

When V is brought below V

CC(off)

increases during start−up. If C

is too small, V will fall

, the start−up

CC(inhibit)

VCC

CC

below V

and the controller will turn off before the

current is reduced to I

(typically 0.5 mA). This limits

CC(off)

start1

auxiliary winding supplies the IC. The total I current after

power dissipation on the device in the event that the V pin

CC

CC(inhibit)

the controller is enabled (I

considered to correctly size C

plus DI ) must be

CC

is shorted to ground. Once V rises back above V

,

CC3

CC

.

the start−up current returns to I

.

VCC

start2

www.onsemi.com

11

NCP1342

Figure 5. Start−up Circuitry Block Diagram

V_HV

V_BO(start)

V_HV(MIN)

V_CC

V_CC(on)

V_CC(off)

Start−up

t_delay(start)

Current = I_start2

Current = I_start1

V_CC(inhibit)

DRV

Figure 6. Start−up Timing

www.onsemi.com

12

NCP1342

DRIVER

The NCP1342 maximum supply voltage, V , is

CC(MAX)

The peak current level is clamped during the soft−start

28 V. Typical high−voltage MOSFETs have a maximum

gate voltage rating of 20 V. The DRV pin incorporates an

active voltage clamp to limit the gate voltage on the external

phase. The setpoint is actually limited by a clamp level

ramping from 0 to 0.8 V within 4 ms.

In addition to the PWM comparator, a dedicated

comparator monitors the current sense voltage, and if it

MOSFETs. The DRV voltage clamp, V

12 V with a maximum limit of 14 V.

is typically

DRV(high)

reaches the maximum value, V

(typically 800 mV), the

ILIM

gate driver is turned off and the overload timer is enabled.

This occurs even if the limit imposed by the feedback

REGULATION CONTROL

Peak Current Control

The NCP1342 is a peak current−mode controller, thus the

FB voltage sets the peak current flowing in the transformer

and the MOSFET. This is achieved by sensing the MOSFET

current across a resistor and applying the resulting voltage

ramp to the non−inverting input of the PWM comparator

through the CS pin. The current limit threshold is set by

voltage is higher than V

. Due to the parasitic

ILIM1

capacitances of the MOSFET, a large voltage spike often

appears on the CS Pin at turn−on. To prevent this spike from

falsely triggering the current sense circuit, the current sense

signal is blanked for a short period of time, t

(typically

LEB1

275 ns), by a leading edge blanking (LEB) circuit. Figure 7

shows the schematic of the current sense circuit.

The peak current is also limitied to a minimum level,

applying the FB voltage divided by K (typically 4) to the

FB

V

(0.2 V, typically). This results in higher efficiency

CS(MIN)

inverting input of the PWM comparator. When the current

sense voltage ramp exceeds this threshold, the output driver

is turned off, however, the peak current is affected by several

functions (see Figure 7):

at light loads by increasing the minimum energy delivered

per switching cycle, while reducing the overall number of

switching cycles during light load.

R

OPP

ZCD/OPP

OPP

V

FB(open)

Minimum Peak

Current

R

+

FB

*

DRV Off

V

ILIM1

V

CS(MIN)

Soft−Start

Ramp

K

FB

*

+

PWM

*

+

OCP

*

+

CS

t

LEB1

LEB2

Overload Timer

R

sense

AOCP

t

+

Abnormal OCP Counter

*

V

ILIM2

Figure 7. Current Sense Logic

www.onsemi.com

13

NCP1342

Zero Current Detection

As shown by Figure 13, a valley is detected once the ZCD

pin voltage falls below the demagnetization threshold,

The NCP1342 is a quasi−resonant (QR) flyback

controller. While the power switch turn−off is determined by

the peak current set by the feedback loop, the switch turn−on

is determined by the transformer demagnetization. The

demagnetization is detected by monitoring the transformer

auxiliary winding voltage.

V

, typically 55 mV. The controller will either switch

ZCD(trig)

once the valley is detected or increment the valley counter,

depending on the FB voltage.

Overpower Protection

The average bulk capacitor voltage of the QR flyback

varies with the RMS line voltage. Thus, the maximum

power capability at high line can be much higher than

desired. An integrated overpower protection (OPP) circuit

provides a relatively constant output power limit across the

Turning on the power switch once the transformer is

demagnetized has the benefit of reduced switching losses.

Once the transformer is demagnetized, the drain voltage

starts ringing at a frequency determined by the transformer

magnetizing inductance and the drain lump capacitance,

eventually settling at the input voltage. A QR flyback

controller takes advantage of the drain voltage ringing and

turns on the power switch at the drain voltage minimum or

“valley” to reduce switching losses and electromagnetic

interference (EMI).

input voltage on the bulk capacitor, V . Since it is a

bulk

high−voltage rail, directly measuring V

will contribute

bulk

losses in the sensing network that will greatly impact the

standby power consumption. The NCP1342 OPP circuit

achieves this without the need for a high−voltage sensing

network, and is essentially lossless.

V

FB(open)

R

FB

PWM

K

FB

t

LEB1

CS

OCP

DRV Off

V

OPP

ZCD/OPP

V

ILIM1

Figure 8. OPP Circuit Schematic

www.onsemi.com

14

NCP1342

⎝

⎛

⎢

⎝

N_AUX

N_P

⎢

.

−

V_BULK

⎛

Figure 9. Auxiliary Winding Voltage

Since the auxiliary winding voltage during the power

switch on time is a reflection of the input voltage scaled by

the primary to auxiliary winding turns ratio, N (see

Figure 9), OPP is achieved by scaling down reflected

voltage during the on−time and applying it to the ZCD pin

The ratio between R

Equation 5. It is obtained by combining Equations 3 and 4.

and R

is given by

OPPL

ZCD

P:AUX

R_ZCD

R_OPPL

V_AUX* V_F* V_ZCD

(eq. 5)

+

V_ZCD

A design example is shown below:

System Parameters:

as a negative voltage, V . The voltage is scaled down by

OPP

a resistor divider comprised of R

and R . The

OPPL

OPPU

V_AUX+ 18 V

V_F+ 0.6 V

maximum internal current setpoint (V

) is simply the

CS(OPP)

sum of V

and the peak current sense threshold, V

.

OPP

ILIM1

Figure 8 shows the schematic for the OPP circuit.

The adjusted peak current limit is calculated using

Equation 2. For example, a V of −150 mV results in a

N_P:AUX+ 0.18

The ratio between R

and R

is calculated using

OPPL

OPP

ZCD

peak current limit of 650 mV in NCP1342.

Equation 5 for a minimum V

of 8 V.

ZCD

R_ZCD

R_OPPL

V_CS(OPP)+ V_OPP) V_ILIM1

18 V * 0.6 V * 8 V

(eq. 2)

+

+ 1.2 kW

8 V

To ensure optimal zero−crossing detection, a diode is

needed to bypass R

used to calculate R

during the off−time. Equation 3 is

R

is arbitrarily set to 1 kW. R

is also set to 1 kW

OPPU

ZCD

OPPL

and R

.

because the ratio between the resistors is close to 1.

The NCP1342 maximum overpower compensation or

peak current setpoint reduction is 31.25% for a V

−250 mV. We will use this value for the following example:

Substituting values in Equation 3 and solving for R

we obtain:

OPPL

R_ZCD) R

N_P:AUX@ V_bulk* V_OPP

^OPPU+ *

(eq. 3)

of

OPP

R_OPPL

V_OPP

R

OPPU

is selected once a value is chosen for R

.

OPPL

OPPU

R

OPPL

is selected large enough such that enough voltage is

available for the zero−crossing detection during the

off−time. It is recommended to have at least 8 V applied on

the ZCD pin for good detection. The maximum voltage is

R_ZCD) R_OPPU

0.18 @ 370 V * (−0.25 V)

+

+ 271

R_OPPL

−0.25 V

internally clamped to V . The off−time voltage on the ZCD

R_OPPU+ 271 @ R_OPPL* R_ZCD

CC

Pin is given by Equation 4.

R_OPPU+ 271 @ 1 kW * 1 kW + 270 kW

R_OPPL

R_ZCD) R_OPPL

ǒ Ǔ

@ V_AUX* V_F

(eq. 4)

V_ZCD

+

For optimum performance over temperature, it is

recommended to keep R below 3 kW.

OPPL

Where V

is the voltage across the auxiliary winding

AUX

and V is the D

forward voltage drop.

F

OPP

www.onsemi.com

15

NCP1342

Soft−Start

in CCM for several cycles until the voltage on the ZCD pin

is high enough to prevent the timer from running. Therefore,

Soft−start is achieved by ramping up an internal reference,

V

, and comparing it to the current sense signal.

a longer timeout period, t

during soft−start to prevent CCM operation.

(typically 100 ms), is used

SSTART

tout1

ramps up from 0 V once the controller initially

SSTART

powers up. The peak current setpoint is then limited by the

ramp resulting in a gradual increase of the switch

Frequency Jittering

V

SSTART

In order to help meet stringent EMI requirements, the

NCP1342 features frequency jittering to average the energy

peaks over the EMI frequency range. As shown in Figure 10,

the function consists of summing a triangular wave of

current during start−up. The soft−start duration, t

typically 4 ms.

, is

SSTART

During startup, demagnetization phases are long and

difficult to detect since the auxiliary winding voltage is very

small. In this condition, the 6 ms steady−state timeout is

generally shorter than the inductor demagnetization period.

If it is used to restart a switching cycle, it can cause operation

amplitude V

and frequency f

with the CS signal

jitter

immediately before the PWM comparator. This current acts

to modulate the on−time and hence the operation frequency.

V

DD

R

FB

K

FB

V

jitter

LEB

CS

V

OPP

DRV Off

V

ILIM1

V

CS(MIN)

Figure 10. Jitter Implementation

1000

Since the jittering function modulates the peak current

level, the FB signal will attempt to compensate for this effect

in order to limit the output voltage ripple. Therefore, the

bandwidth of the feedback loop must be well below the jitter

frequency, or the jitter function will be filtered by the loop.

Due to the minimum peak current, the effect of the

jittering circuit will not be seen during frequency foldback

mode.

900

800

700

600

500

400

300

200

100

0

Maximum Frequency Clamp

All 9−pin versions of the NCP1342 include an adjustable

maximum frequency clamp via an external resistor from the

FMAX Pin to ground. It can also be disabled by pulling the

FMAX pin above 4 V. The maximum frequency can be

programmed using Equation 6, and is shown in Figure 11.

0

50

100

150 200

250

300 350 250

R

(kW)

FMAX

Figure 11. F_SW(MAX)vs. R_FMAX

261 kHz * 1 V

(eq. 6)

+

F_SW(MAX)

R_FMAX* 10 mA

www.onsemi.com

16

NCP1342

LIGHT LOAD MANAGEMENT

a valley is selected, the controller stays locked in this valley

until the output power changes significantly. This technique

extends the QR mode operation over a wider output power

range while maintaining good efficiency and limiting the

maximum operating frequency.

The operating valley (1 , 2 , 3 4 , 5 or 6 ) is

determined by the FB voltage. An internal counter

increments each time a valley is detected by the ZCD/OPP

Pin. Figure 12 shows a typical frequency characteristic

obtainable at low line in a 65 W application.

Valley Lockout Operation

The operating frequency of a traditional QR flyback

controller is inversely proportional to the system load. In

other words, a load reduction increases the operating

frequency. A maximum frequency clamp can be useful to

limit the operating frequency range. However, when used by

itself, such an approach often causes instabilities since when

this clamp is active, the controller tends to jump (or hesitate)

between two valleys, thus generating audible noise.

Instead, the NCP1342 also incorporates a patented valley

lockout (VLO) circuitry to eliminate valley jumping. Once

st

nd

rd, th

th

6^th5^th4^th

3^rd

2^nd

1^st

5

4

1x10

8x10

6x10

4x10

2x10

VCO

mode

6^th

5^th4^th

3^rd

2^nd

1^st

VCO

mode

0

20

40

60

Pout (W)

Figure 12. Valley Lockout Frequency vs. Output Power

When an “n” valley is asserted by the valley selection

circuitry, the controller is locked in this valley until the FB

voltage decreases to the lower threshold (“n+1” valley

activates) or increases to the “n valley threshold” + 600 mV

(“n−1” valley activates). The regulation loop adjusts the

peak current to deliver the necessary output power. Each

valley selection comparator features a 600 mV hysteresis

that helps stabilize operation despite the FB voltage swing

produced by the regulation loop.

Table 6. VALLEY FB THRESHOLDS (typical values)

FB Falling

FB Rising

st

nd

st

1

to 2 valley

1.400 V

1.200 V

1.100 V

1.000 V

0.900 V

2

to 1 valley

2.000 V

1.800 V

1.700 V

1.600 V

1.500 V

nd

rd

th

nd

2

to 3 valley

3

to 2 valley

th

rd

3

4

5

to 4 valley

4

5

to 3 valley

th

to 5 valley

to 4 valley

th

to 6 valley

6

to 5 valley

Valley Timeout

signal acts as a substitute for the ZCD signal to the valley

counter. Figure 13 shows the valley timeout circuit

In case of extremely damped oscillations, the ZCD

comparator may not be able to detect the valleys. In this

condition, drive pulses will stop while the controller waits

for the next valley or ZCD event. The NCP1342 ensures

continued operation by incorporating a maximum timeout

period after the last demagnetization detection. The timeout

schematic. The steady state timeout period, t

, is set at 6

tout2

ms (typical) to limit the frequency step.

During startup, the voltage offset added by the OPP diode,

, prevents the ZCD Comparator from accurately

D

OPP

detecting the valleys. In this condition, the steady state

www.onsemi.com

17

NCP1342

timeout period will be shorter than the inductor

the FB voltage sets VLO mode to turn on at the fifth valley,

and the ZCD ringing is damped such that the ZCD circuit is

only able to detect:

demagnetization period causing CCM operation. CCM

operation lasts for a few cycles until the voltage on the ZCD

pin is high enough to detect the valleys. A longer timeout

• Valleys 1 to 4: the circuit generates a DRV pulse 6 ms

th

period, t

, (typically 100 ms) is set during soft−start to

tout1

(steady−state timeout delay) after the 4 valley

limit CCM operation.

detection.

In VLO operation, the number of timeout periods are

counted instead of valleys when the drain−source voltage

oscillations are too damped to be detected. For example, if

• Valleys 1 to 3: the timeout delay must run twice, and

rd

the circuit generates a DRV pulse 12 ms after the 3

valley detection.

Figure 13. Valley Timeout Circuitry

Frequency Foldback with Minimum Peak Current

Modulation (MPCM)

As the output load decreases (FB voltage decreases), the

valleys are incremented from 1 to 6. When the sixth valley

is reached and the FB voltage further decreases to

minimum frequency clamp prevents the switching

frequency from dropping below 25 kHz to eliminate the risk

of audible noise. Note that the dead−time is not added (it is

blanked) until MPCM is engaged to ensure valley switching

prior to entering MPCM mode.

V

(800 mV typical), the controller enters MPCM

MPCM(entry)

In addition to dead−time, the peak current setpoint is

and begins frequency foldback (FF). At this point, the

minimum peak current is increased by V

linearly reduced as V falls down to 0.4 V. This ensures that

FB

MPCM(delta)

the peak current is not too high during the lightest loads, and

has the effect of reducing the skip entry power level.

Figure 14 shows the MPCM with respect to the feedback

voltage, while Figure 15 shows the VLO to FF operation.

To reduce the output power hysteresis between entering

(400 mV typical). The increase in peak current serves to

force the switching frequency to a much lower value, thus

improving the efficiency at light loads. During this mode,

the controller regulates the power delivery by modulating

the switching frequency.

and exiting MPCM, the exit threshold (V

) is set

MPCM(exit)

Once in frequency foldback mode, the controller reduces

slightly below the entry threshold (750 mV typical). A 1 ms

timer, t , is engaged every time MPCM is entered or

th

the switching frequency by adding dead−time after the 6

MPCM

valley is detected. This dead−time increases as the FB

voltage decreases.

The dead−time circuit is designed to add 0 ms dead−time

exited to prevent oscillations during the operating point

transition. If at any time FB falls to skip mode, or rises to 5

valley, MPCM will be immediately exited regardless of

th

when V = 0.4 V and linearly increases the total dead−time

FB

DT(MAX)

t

.

MPCM

to t

(36 ms typical) as V falls down to 0.4 V. The

FB

www.onsemi.com

18

NCP1342

Minimum Peak Current

V

+ V

MPCM(delta)

CS(MIN)

V

MPCM(delta)

V

CS(MIN)

V_FB

V

MPCM(entry)

V_skip

Figure 14. Minimum Peak Current Modulation

Operating Mode

V

decreases

increases

FB

FF

V

FB

Valley 6

Valley 5

Valley 4

Valley 3

Valley 2

Fault !

Valley 1

V

(V)

3.2

0.8 0.9 1.0 1.1 1.2 1.4 1.5 1.6 1.7 1.8 2.0

FB

Figure 15. Valley Lockout Thresholds

www.onsemi.com

19

NCP1342

Minimum Frequency Clamp and Skip Mode

as the current drive pulses ends – it does not stop

immediately.

Once switching stops, FB will rise. As soon as FB crosses

the skip−exit threshold, drive pulses will resume, but the

controller remains in burst mode. At this point, a 1.25 ms

As mentioned previously, the circuit prevents the

switching frequency from dropping below f (25 kHz

MIN

typical). When the switching cycle would be longer than

40 ms, the circuit forces a new switching cycle. However, the

f

clamp cannot generate a DRV pulse until the

timer, t

, is started together with a count−to−3 counter.

quiet

MIN

demagnetization is completed. In other words, it will not

cause operation in CCM.

The next time the FB voltage drops below the skip−in

threshold, drive pulses stop at the end of the current pulse as

long as 3 drive pulses have been counted (if not, they do not

Since the NCP1342 forces a minimum peak current and a

minimum frequency, the power delivery cannot be

continuously controlled down to zero. Instead, the circuit

starts skipping pulses when the FB voltage drops below the

skip level, V , and recovers operation when V exceeds

rd

stop until the end of the 3 pulse). They are not allowed to

start again until the timer expires, even if the skip−exit

threshold is reached first. It is important to note that the

timer will not force the next cycle to begin – i.e. if the natural

skip frequency is such that skip−exit is reached after the

timer expires, the drive pulses will wait for the skip−exit

threshold.

This means that during no−load, there will be a minimum

of 3 drive pulses, and the burst−cycle period will likely be

much longer than 1.25 ms. This operation helps to improve

efficiency at no−load conditions.

skip

FB

V

skip

+ V

. This skip−mode method provides an

skip(HYS)

efficient method of control during light loads.

Quiet−Skip

To further avoid acoustic noise, the circuit prevents the

burst frequency during skip mode from entering the audible

range by limiting it to a maximum of 800 Hz. This is

achieved via a timer (t ) that is activated during

quiet

In order to exit burst mode, the FB voltage must rise higher

Quiet−Skip. The start of the next burst cycle is prevented

until this timer has expired.

As the output power decreases, the switching frequency

decreases. Once it hits 25 kHz, the skip−in threshold is

reached and burst mode is entered − switching stops as soon

than 1 V. If this occurs before t

expires, the drive pulses

quiet

will resume immediately – i.e. the controller won’t wait for

the timer to expire. Figure 16 provides an example of how

Quiet−Skip works.

www.onsemi.com

20

NCP1342

MAX

Load

Fsw >= 25 kHz

DRV

FB

1.25 ms

Fsw >= 25 kHz

DRV

FB

DRV

FB

DRV

FB

>1.25 ms

DRV

FB

MIN

Load

Figure 16. Quiet−Skip Timing Diagram

www.onsemi.com

21

NCP1342

FAULT MANAGEMENT

The NCP1342 contains three separate fault modes.

external latch input. When the NCP1342 detects a latching

fault, the driver is immediately disabled. The operation

during a latching fault is identical to that of a non−latching

fault except the controller will not attempt to restart at the

Depending on the type of fault, the device will either latch

off, restart when the fault is removed, or resume operation

after the auto−recovery timer expires.

next V

, even if the fault is removed. In order to clear

CC(on)

Latching Faults

Some faults will cause the NCP1342 to latch off. These

include the abnormal OCP (AOCP), V OVP, and the

the latch and resume normal operation, V must first be

allowed to drop below V

must be detected. This operation is shown in Figure 17.

CC

or a line removal event

CC(reset)

CC

Fault

Applied

Fault

Removed

time

V_CC

V_CC(on)

V_CC(off)

time

FDRV

I_HV

I_{start 2}

I_start(off)

time

Figure 17. Operation During Latching Fault

www.onsemi.com

22

NCP1342

Non−Latching Faults

re−enabled when V reaches V

according to the

CC

CC(on)

When the NCP1342 detects a non−latching fault

(brownout or thermal shutdown), the drivers are disabled,

initial power−on sequence, provided V

is above

HV

V

This operation is shown in Figure 18. When V

BO(start).

HV

and V falls towards V

due to the IC internal current

is reaches V

, V immediately charges to V

.

CC

CC(off)

BO(start)

CC

CC(on)

consumption. Once V reaches V

, the HV current

CC(off)

If V is already above V

when the fault is removed,

CC

CC(on)

source turns on and C

begins to charge towards V

.

the controller will start immediately as long as V is above

VCC

CC(on)

HV

When V , reaches V

, the cycle repeats until the fault

V

CC

CC(on)

BO(start).

is removed. Once the fault is removed, the NCP1342 is

Fault

Applied

Removed

time

Waits for next

V_CC(on)before

starting

V_CC

V_CC(on)

V_{CC(off )}

time

FDRV

I_HV

I_{start 2}

I_{start (off)}

time

Figure 18. Operation During Non−Latching Fault

www.onsemi.com

23

NCP1342

Auto−recovery Timer Faults

Some faults faults cause the NCP1342 auto−recovery

timer to run. If an auto−recovery fault is detected, the gate

running, the HV current source turns on and off to maintain

between V and V . Once the auto−recovery

V

cc

cc(off)

cc(on)

timer expires, the controller will attempt to start normally at

the next V provided V is above V . This

drive is disabled and the auto−recovery timer, t

autorec

CC(on)

HV

BO(start)

(typically 1.2 s), starts. While the auto−recovery timer is

operation is shown in Figure 19.

Fault

Applied

Removed

Fault

time

V_CC

V_CC(on)

V_CC(off)

Restarts

At V_CC(on)

(new burst

cycle if Fault

still present)

time

DRV

Controller

stops

Autorecovery

Timer

1.2 s

t_restart

time

Figure 19. Operation During Auto−Recovery Fault

www.onsemi.com

24

NCP1342

PROTECTION FEATURES

Brownout Protection

Figure 20 shows the brownout detector waveforms during

A timer is enabled once V

drops below its disable

a brownout.

HV

threshold, V

disabled if V

brownout timer, t (typically 54 ms), expires. The timer is

(typically 99 V). The controller is

When a brownout is detected, the controller stops

switching and enters non−latching fault mode (see

Figure 18). The HV current source alternatively turns on and

BO(stop)

doesn’t exceed V

before the

HV

BO(stop)

BO

set long enough to ignore a two cycle dropout. The timer

off to maintain V between V

and V

until the

CC

CC(on)

CC(off)

starts counting once V drops below V

.

input voltage is back above V

.

HV

BO(stop)

BO(start)

V_HV

V_{BO(start )}

V_BO(stop)

time

Fault

Cleared

Brownout

Timer

Brownout

detected

Starts

Charging

Immediately

V_CC

Restarts at

next V _CC(on)

V_CC(on)

V_CC(off)

t_{delay (start )}

time

DRV

Figure 20. Operation During Brownout

Line Removal Detection and X2 Capacitor Discharge

Safety agency standards require the input filter capacitors

to be discharged once the ac line voltage is removed. A

resistor network is the most common method to meet this

requirement. Unfortunately, the resistor network consumes

power across all operating modes and it is a major

contributor of input power losses during light−load and

no−load conditions.

discharge circuitry. A novel approach is used to reconfigure

the high voltage startup circuit to discharge the input filter

capacitors upon removal of the ac line voltage. The line

removal detection circuitry is always active to ensure safety

compliance.

The line removal is detected by digitally sampling the

voltage present at the HV pin, and monitoring the slope.

A timer, t

(typically 100 ms), is used to detect

line(removal)

The NCP1342 eliminates the need for external discharge

resistors by integrating active input filter capacitor

when the slope of the input signal is negative or below the

resolution level. The timer is reset any time a positive slope

www.onsemi.com

25

NCP1342

is detected. Once the timer expires, a line removal condition

drops to V

, it is quickly recharged to V

. The

CC(on)

CC(X2_reg)

is acknowledged initiating an X2 capacitor discharge cycle,

and the controller is disabled.

discharging process is cyclic and continues until the ac line

is detected again or the voltage across the X2 capacitor is

If V is above V

, it is first discharged to V

.

lower than V

(30 V maximum). This feature

CC

CC(on)

HV(discharge)

A second timer, t

the time limiting of the discharge phase to protect the device

against overheating. Once the discharge phase is complete,

(typically 32 ms), is used for

allows the device to discharge large X2 capacitors in the

input line filter to a safe level.

It is important to note that the HV pin cannot be

connected to any dc voltage due to this feature, i.e.

directly to the bulk capacitor.

line(discharge)

t

is reused while the device checks to see if the

line(discharge)

line voltage is reapplied. During the discharge phase, if V

CC

X2 Capacitor

Discharge

V_HV

V_BO(start)

V_BO(stop)

X2 Capacitor

Discharge

AC Line Unplug

V_{HV(discharge )}

time

AC

Timer

Starts

Timer

Restarts

Timer

Expires

No AC Detection

Timer

t_{line(removal )}

t_{line(discharge /detect)}

t_{line(discharge )}

t_{line(removal )}

t_line(detect)

DRV

time

X2 Discharge

Device is stopped

X2 Discharge

Current

I_start2

I_CC

I_{CC(discharge )}

0

I_CC3

I_start2

V_CC

V_{CC(X2_reg)}

V_CC(on)

Figure 21. Line Removal Timing

www.onsemi.com

26

NCP1342

X2 Capacitor

Discharge

VHV

V_BO(start)

V_BO(stop)

AC Line Unplug

V_{HV(discharge )}

time

AC

Timer

Expires

AC Detected

AC

Timer

Starts

Timer

Restarts

Timer

t_{line(removal )}

t_{line(discharge /detect )}

time

t_{line(discharge )}

t_{line(removal )}

DRV

X2 Discharge

Device is stopped

X2 Discharge

Current

t_delay(start)

I_start2

time

I_CC

I_{CC(discharge )}

0

I_CC3

I_start2

V_CC

V_{CC(X2_reg)}

V_CC(on)

Figure 22. Line Removal Timing with AC Reapplied

An over temperature protection block monitors the

junction temperature during the discharge process to avoid

thermal runaway, in particular during open/short pins safety

tests. Please note that the X2 discharge capability is also

active at all times, including off−mode and before the

controller actually starts to pulse (e.g. if the user unplugs the

converter during the start−up sequence).

the lower fault threshold, V

(typically 0.4 V).

Fault(OTP_in)

The lower threshold is normally used for detecting an

overtemperature fault. The controller operates normally

while the Fault pin voltage is maintained within the upper

and lower fault thresholds. Figure 23 shows the architecture

of the Fault input.

The Fault input signal is filtered to prevent noise from

triggering the fault detectors. Upper and lower fault detector

Dedicated Fault Input

blanking delays, t

and t

,are both

delay(OTP)

delay(OVP)

The NCP1342 includes a dedicated fault input accessible

via the Fault pin (8−pin and 9−pin versions only). The

controller can be latched by pulling up the pin above the

typically 30 ms. A fault is detected if the fault condition is

asserted for a period longer than the blanking delay.

upper fault threshold, V

(typically 3.0 V). The

Fault(OVP)

controller is disabled if the Fault pin voltage is pulled below

www.onsemi.com

27

NCP1342

OVP

voltage drop across the thermistor. The resistance of the

An active clamp prevents the Fault pin voltage from

NTC thermistor decreases at higher temperatures resulting

in a lower voltage across the thermistor. The controller

detects a fault once the thermistor voltage drops below

reaching the upper latch threshold if the pin is open. To reach

the upper threshold, the external pull−up current has to be

higher than the pull−down capability of the clamp (set by

V

.

Fault(OTP_in)

R

at V ), i.e., approximately 1 mA.

Fault(clamp)

The controller bias current is reduced during power up by

Fault(clamp)

The upper fault threshold is intended to be used for an

disabling most of the circuit blocks including I

.

Fault(OTP)

overvoltage fault using a zener diode and a resistor in series

from the auxiliary winding voltage. The controller is latched

This current source is enabled once V reaches V

. A

CC

CC(on)

filter capacitor is typically connected between the Fault and

GND pins. This will result in a delay before V reaches

once V

exceeds V

.

Fault

Fault(OVP)

Fault

Once the controller is latched, it follows the behavior of

a latching fault according to Figure 17 and is only reset if

its steady state value once I

the lower fault comparator (i.e. overtemperature detection)

is ignored during soft−start.

is enabled. Therefore,

Fault(OTP)

V

CC

is reduced to V

, or X2 discharge is activated. In

CC(reset)

the typical application these conditions occur only if the ac

voltage is removed from the system.

Version

A latches off the controller after an

overtemperature fault is detected according to Figure 17. In

Version B, the controller is re−enabled once the fault is

removed such that V

the auto−recovery timer expires, and V reaches V

as shown in Figure 19.

OTP

increases above V

,

Fault

Fault(OTP_out)

The lower fault threshold is intended to be used to detect

an overtemperature fault using an NTC thermistor. A pull up

CC

CC(on)

current source, I

(typically 45.0 mA), generates a

Fault(OTP)

Figure 23. Fault Pin Internal Schematic

www.onsemi.com

28

NCP1342

Overload Protection

• The controller latches off (version A) or

The overload timer integrates the duration of the overload

fault. That is, the timer count increases while the fault is

present and reduces its count once it is removed. The

overload timer duration, t

the overload timer expires, the controller detects an overload

condition does one of the following:

• Enters a safe, low duty−ratio auto−recovery mode

(version B).

Figure 24 shows the overload circuit schematic, while

Figure 25 and Figure 26 show operating waveforms for

latched and auto−recovery overload conditions.

, is typically 160 ms. When

OVLD

V

FB(open)

R

FB

PWM

K

FB

t

OVLD

LEB1

CS

OCP + OPP

Count Down

Count Up

V

OPP

ZCD/OPP

V

ILIM1

DRV Off

AOCP

t

LEB2

Abnormal OCP

Count 4

V

ILIM2

Figure 24. Overload Circuitry

www.onsemi.com

29

NCP1342

Latch

Event

Fault

Latch

time

V_CC

V_CC(on)

V_CC(off)

time

DRV

I_HV

I_start2

I_HV(off)

time

Figure 25. Latched Overload Operation

www.onsemi.com

30

NCP1342

Fault

disappears

Overcurrent

applied

Output Load

Max Load

time

Fault Flag

Fault

timer

starts

V_CC

V_CC(on)

V_CC(off)

Restarts

At V_CC(on)

(new burst

cycle if Fault

still present)

time

DRV

Controller

stops

Fault timer

160 ms

time

t_OVLD

t_restart

t_delay(start)

Figure 26. Auto−Recovery Overload Operation

www.onsemi.com

31

NCP1342

Abnormal Overcurrent Protection (AOCP)

core. Due to the valley timeout feature of the controller, the

flux level will quickly walk up until the core saturates. This

can cause excessive stress on the primary MOSFET and

secondary diode. This is not a problem for the NCP1342,

however, because the valley timeout timer is disabled while

the ZCD Pin voltage is above the arming threshold. Since the

leakage energy is high enough to arm the ZCD trigger, the

timeout timer is disabled and the next drive pulse is delayed

until demagnetization occurs.

Under some severe fault conditions, like a winding

short−circuit, the switch current can increase very rapidly

during the on−time. The current sense signal significantly

exceeds V

, but because the current sense signal is

ILIM1

blanked by the LEB circuit during the switch turn−on, the

power switch current can become huge and cause severe

system damage.

The NCP1342 protects against this fault by adding an

additional comparator for Abnormal Overcurrent Fault

detection. The current sense signal is blanked with a shorter

V_CCOvervoltage Protection

An additional comparator on the V pin monitors the

CC

LEB duration, t

, typically 125 ns, before applying it to

LEB2

V

CC

voltage. If VCC exceeds VCC(OVP), the gate drive is

the Abnormal Overcurrent Fault Comparator. The voltage

threshold of the comparator, V , typically 1.2 V, is set

disabled and the NCP1342 follows the operation of a

latching fault (see Figure 17).

ILIM2

50% higher than V

, to avoid interference with normal

ILIM1

operation. Four consecutive Abnormal Overcurrent faults

cause the controller to enter latch mode. The count to 4

provides noise immunity during surge testing. The counter

is reset each time a DRV pulse occurs without activating the

Fault Overcurrent Comparator.

Thermal Shutdown

An internal thermal shutdown circuit monitors the

junction temperature of the controller. The controller is

disabled if the junction temperature exceeds the thermal

shutdown threshold, T

(typically 140°C). When a

SHDN

thermal shutdown fault is detected, the controller enters a

non−latching fault mode as depicted in Figure 18. The

Current Sense Pin Failure Protection

A 1mA (typically) pull−up current source, I , pulls up the

CS pin to disable the controller if the pin is left open.

Additionally, the maximum on−time, t

typically), prevents the MOSFET from staying on

permanently if the CS Pin is shorted to GND.

CS

controller restarts at the next V

once the junction

CC(on)

temperature drops below below T

by the thermal

SHDN

(32 ms

on(MAX)

shutdown hysteresis, T

The thermal shutdown is also cleared if V drops below

, typically 40°C.

SHDN(HYS)

CC

V

, or a line removal fault is detected. A new power

CC(reset)

Output Short Circuit Protection

During an output short−circuit, there is not enough

voltage across the secondary winding to demagnetize the

up sequence commences at the next V

faults are removed.

once all the

CC(on)

www.onsemi.com

32

NCP1342

TYPICAL CHARACTERISTICS

17.14

17.12

17.1

9

8.99

8.98

8.97

8.96

8.95

8.94

8.93

17.08

17.06

17.04

17.02

17

16.98

16.96

16.94

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 27. V_CC(on)vs. Temperature

Figure 28. V_CC(off)vs. Temperature

0.6

0.5

0.4

0.3

0.2

0.1

0

5

4.5

4

3.5

3

2.5

2

1.5

1

0.5

0

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 29. I_start1vs. Temperature

Figure 30. I_start2vs. Temperature

7

6

5

4

3

2

1

0

9

8

7

6

5

4

3

2

1

0

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 31. I_HV(off1)vs. Temperature

Figure 32. I_HV(off2)vs. Temperature

www.onsemi.com

33

NCP1342

TYPICAL CHARACTERISTICS

0.126

0.124

0.122

0.120

0.118

0.116

0.114

0.112

0.110

0.108

0.106

0.255

0.250

0.245

0.240

0.235

0.230

0.225

0.220

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 33. I_CC1vs. Temperature

Figure 34. I_CC2vs. Temperature

1.075

1.070

1.065

1.060

1.055

1.050

1.045

1.040

1.035

1.030

28.35

28.3

28.25

28.2

28.15

28.1

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 35. I_CC3vs. Temperature

Figure 36. V_CC(OVP)vs. Temperature

19.8

19.6

19.4

19.2

19

112.6

112.4

112.2

112

111.8

111.6

111.4

111.2

110

18.8

18.6

18.4

18.2

18

17.8

17.6

110.8

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 37. I_{CC(discharge)}vs. Temperature

Figure 38. V_BO(start)vs. Temperature

www.onsemi.com

34

NCP1342

TYPICAL CHARACTERISTICS

98.2

98

90

80

70

60

50

40

30

20

10

0

CDRV = 1 nF

97.8

97.6

97.4

97.2

97

CDRV = 100 pF

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 39. V_BO(stop)vs. Temperature

Figure 40. t_DRV(rise)vs. Temperature

45

40

35

30

25

20

15

10

5

111.8

111.6

111.4

111.2

111

CDRV = 1 nF

110.8

110.6

110.4

110.2

CDRV = 100 pF

0

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 41. t_DRV(fall)vs. Temperature

Figure 42. f_MAX1vs. Temperature

367

366.5

366

73.45

73.4

73.35

73.3

73.25

73.2

73.15

73.1

73.05

73

365.5

365

364.5

364

363.5

363

362.5

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 43. f_MAX2vs. Temperature

Figure 44. f_MAX3vs. Temperature

www.onsemi.com

35

NCP1342

TYPICAL CHARACTERISTICS

32.5

32.4

32.3

32.2

32.1

32

63.6

63.5

63.4

63.3

63.2

63.1

63

31.9

31.8

31.7

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 45. t_on(MAX)vs. Temperature

Figure 46. V_ZCD(trig)vs. Temperature

25.65

25.6

12.95

12.9

12.85

12.8

25.55

25.5

25.45

25.4

12.75

25.35

12.7

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 47. V_ZCD(HYS)vs. Temperature

Figure 48. V_ZCD(MAX)vs. Temperature

0

−0.1

−0.2

−0.3

−0.4

−0.5

−0.6

−0.7

−0.8

−0.9

198.8

198.6

198.4

198.2

198

197.8

197.6

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 49. V_ZCD(MIN)vs. Temperature

Figure 50. V_freezevs. Temperature

www.onsemi.com

36

NCP1342

TYPICAL CHARACTERISTICS

1.31

1.308

1.306

1.304

1.302

1.3

104.2

104

103.8

103.6

103.4

103.2

103

1.298

1.296

1.294

102.8

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 51. f_jittervs. Temperature

Figure 52. V_jittervs. Temperature

3.1

3.09

3.08

3.07

3.06

3.05

3.04

3.03

402.5

402

401.5

401

400.5

400

399.5

399

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 53. V_Fault(OVP)vs. Temperature

Figure 54. V_{Fault(OTP_in)}vs. Temperature

920

918

916

914

912

910

908

906

45.1

45

44.9

44.8

44.7

44.6

44.5

44.4

44.3

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 55. V_{Fault(OTP_out)}vs. Temperature

Figure 56. I_OTPvs. Temperature

www.onsemi.com

37

NCP1342

TYPICAL CHARACTERISTICS

1.731

1.73

1.55

1.545

1.54

1.535

1.53

1.729

1.728

1.727

1.726

1.525

1.52

1.515

1.51

1.505

1.5

1.495

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 57. V_Fault(clamp)vs. Temperature

Figure 58. R_Fault(clamp)vs. Temperature

24.5

24.45

24.4

1.39

1.385

1.38

24.35

24.3

24.25

24.2

1.375

1.37

24.15

24.1

24.05

1.365

24

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 59. f_MINvs. Temperature

Figure 60. t_quietvs. Temperature

840

830

820

810

800

790

780

0.8

0.799

0.798

0.797

0.796

0.795

0.794

0.793

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 61. t_ZCD(blank)vs. Temperature

Figure 62. V_ILIM1vs. Temperature

www.onsemi.com

38

NCP1342

TYPICAL CHARACTERISTICS

1.202

1.201

1.2

40

39.9

39.8

39.7

39.6

39.5

39.4

39.3

39.2

39.1

1.199

1.198

1.197

1.196

1.195

1.194

1.193

−40

−20

0

20

40

60

80

100 120

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

T , JUNCTION TEMPERATURE (°C)

J

Figure 64. t_DT(MAX)vs. Temperature

Figure 63. V_ILIM2vs. Temperature

399

398.5

398

397.5

397

396.5

396

−40

−20

0

20

40

60

80

100 120

T , JUNCTION TEMPERATURE (°C)

J

Figure 65. V_skipvs. Temperature

www.onsemi.com

39

NCP1342

PACKAGE DIMENSIONS

SOIC−8 NB

CASE 751−07

ISSUE AK

NOTES:

1. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

−X−

A

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSION A AND B DO NOT INCLUDE

MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

PER SIDE.

8

5

4

5. DIMENSION D DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.127 (0.005) TOTAL

IN EXCESS OF THE D DIMENSION AT

MAXIMUM MATERIAL CONDITION.

6. 751−01 THRU 751−06 ARE OBSOLETE. NEW

STANDARD IS 751−07.

S

M

B

0.25 (0.010)

Y

1

K

−Y−

MILLIMETERS

DIM MIN MAX

INCHES

G

MIN

MAX

0.197

0.157

0.069

0.020

A

B

C

D

G

H

J

K

M

N

S

4.80

3.80

1.35

0.33

5.00 0.189

4.00 0.150

1.75 0.053

0.51 0.013

C

N X 45

_

SEATING

PLANE

1.27 BSC

0.050 BSC

−Z−

0.10

0.19

0.40

0

0.25 0.004

0.25 0.007

1.27 0.016

0.010

0.050

8

0.020

0.244

0.10 (0.004)

M

J

H

D

8

0

_

0.25

5.80

0.50 0.010

6.20 0.228

M

S

X

0.25 (0.010)

Z

Y

SOLDERING FOOTPRINT*

1.52

0.060

7.0

4.0

0.275

0.155

0.6

0.024

1.270

0.050

mm

inches

ǒ

Ǔ

SCALE 6:1

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

www.onsemi.com

40

NCP1342

PACKAGE DIMENSIONS

SOIC−9 NB

CASE 751BP

ISSUE A

2X

NOTES:

0.10

C

A-B

0.10

1. DIMENSIONING AND TOLERANCING PER

ASME Y14.5M, 1994.

D

2. CONTROLLING DIMENSION: MILLIMETERS.

3. DIMENSION b DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE PROTRUSION

SHALL BE 0.10mm TOTAL IN EXCESS OF ’b’

AT MAXIMUM MATERIAL CONDITION.

4. DIMENSIONS D AND E DO NOT INCLUDE

MOLD FLASH, PROTRUSIONS, OR GATE

BURRS. MOLD FLASH, PROTRUSIONS, OR

GATE BURRS SHALL NOT EXCEED 0.15mm

PER SIDE. DIMENSIONS D AND E ARE DE-

TERMINED AT DATUM F.

D

H

A

2X

0.20

C

4 TIPS

C A-B

F

10

6

E

1

5. DIMENSIONS A AND B ARE TO BE DETERM-

INED AT DATUM F.

6. A1 IS DEFINED AS THE VERTICAL DISTANCE

FROM THE SEATING PLANE TO THE LOWEST

POINT ON THE PACKAGE BODY.

5

L2

A3

SEATING

PLANE

L

C

0.20

C

9X b

DETAIL A

B

5 TIPS

M

MILLIMETERS

0.25

C A-B D

DIM MIN

MAX

1.75

0.25

0.51

5.00

4.00

TOP VIEW

A

A1

A3

b

1.25

0.10

0.17

0.31

4.80

3.80

9X

h

X 45

_

0.10

C

0.10

C

D

E

M

e

1.00 BSC

H

5.80

6.20

h

L

L2

M

0.37 REF

A

0.40

0

1.27

DETAIL A

e

SIDE VIEW

A1

SEATING

PLANE

0.25 BSC

C

8

_

END VIEW

RECOMMENDED

SOLDERING FOOTPRINT*

1.00

PITCH

9X

0.58

6.50

1

9X

1.18

DIMENSION: MILLIMETERS

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

ON Semiconductor and

are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.

ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent

coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.

ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,

regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or

specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer

application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not

designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification

in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized

application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and

expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such

claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This

literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT:

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

Literature Distribution Center for ON Semiconductor

19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

For additional information, please contact your local

Sales Representative

◊

NCP1342/D

www.onsemi.com

41


型号：	NCP1342ADDCDAD1R2G
厂家：	ONSEMI
描述：	准谐振反激控制器，带谷锁闭开关开关反激控制控制器
文件：	总41页 (文件大小：882K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

NCP1342ADDCDAD1R2G [ONSEMI]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E