NCP4371ACCDR2G [ONSEMI]
3.0 HVDCP Controller;![NCP4371ACCDR2G](http://pdffile.icpdf.com/pdf2/p00327/img/icpdf/NCP4371_2012006_icpdf.jpg)
型号: | NCP4371ACCDR2G |
厂家: | ![]() |
描述: | 3.0 HVDCP Controller |
文件: | 总14页 (文件大小:164K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
NCP4371
Product Preview
Qualcomm Quick Charget
3.0 HVDCP Controller
NCP4371 is a USB secondary side fast−charging controller,
supporting Qualcomm Quick Charge 3.0 (QC 3.0) High Voltage
Dedicated Charging Port (HVDCP) Class A and Class B specification.
NCP4371 allows for selection of the output voltage of an AC−DC USB
adapter based on commands from the Portable Device (PD) being
powered. Selecting a higher charging voltage will reduce the charging
current for a given power level resulting in reduced IR drops and
increased system efficiency. Another advantage of QC3.0 is a decreased
battery charging time and a reduced PD system cost thanks to the
ability to select an optimum charging voltage. This eliminates the need
for costly DC−DC converters within the PD. The USB−bus voltage
can be controlled in discreet steps from 3.6 V up to 20 V. The output
current is limited not to exceed maximum allowable power level.
The NCP4371 resides at the secondary (isolated) side of the adapter.
It includes voltage and current feedback regulation eliminating the
need for a shunt regulator such as TL431.
www.onsemi.com
8
1
SOIC−8
D SUFFIX
CASE 751
MARKING DIAGRAM
8
XXXXX
ALYWG
G
The NCP4371 provides charging current limits down to
VBUS = 2.2 V protecting the portable device from excessive currents
in case of a soft short−circuit condition.
The NCP4371 integrates a safe−discharge circuitry to quickly and
reliably discharge output capacitors in case the USB cable is
unplugged or connected to a 5 V only USB port.
1
XXXXX = Specific Device Code
A
L
Y
W
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
Features
• Supports Qualcomm Quick Charge 3.0 HVDCP Class A/B
• Output Voltage Can be Configured in Discreet Steps from
PIN CONNECTIONS
♦ Class A: 3.6 V up to 12 V
♦ Class B: 3.6 V up to 20 V
VCC
GND
D−
DISCHARGE
DRIVE
• Compatible with USB Battery Charging Specification Revision 1.2
(USB BC1.2)
ISNS
• Constant Voltage and Constant Current Regulation
D+
COMP
• Soft Short−Circuit Current Limitation Down to V
= 2.2 V
BUS
(Top View)
• Removes a Need for the Secondary Side Shunt Regulator such as
TL431
• Output Capacitor Safe−Discharge Circuitry at Cable Unplug
• Fast Dynamic Response
ORDERING INFORMATION
See detailed ordering, marking and shipping information in the
package dimensions section on page 13 of this data sheet.
• Built−in Power Limiting Function
• Low Supply Current
• Wide Operating Input Voltage Range: 2.2 V to 28 V
• This is Pb−free Device
Typical Applications
• Fast Charging AC/DC Adapters for Smart Phones, Tablets and Other
Portable Devices
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
© Semiconductor Components Industries, LLC, 2015
1
Publication Order Number:
September, 2015 − Rev. P0
NCP4371/D
NCP4371
R_SENSE
R_DIS
Figure 1. Typical Application Schematic
www.onsemi.com
2
NCP4371
VCC
DISCHARGE
I
V
DISCHARGE
CC
Power
RESET
management
V
DDD
SW
V
DDA
V
CC(UVLO)
GND
DRIVE
R
DM_DWN
Sink only
D−
ISNS
OTA
V
REFV
Current
Regulation
V
REFC
V
CC
R
VSNS_UP
Sink only
OTA
D+
COMP
V
REFC
Voltage
Regulation
V
REFV
R
DAT_LKG
R
VSNS_DWN
Figure 2. Simplified Block Diagram
Table 1. PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
DISCHARGE
DRIVE
Description
1
2
This output is used to safely discharge V
output capacitors when an unplug event is detected
BUS
Output of current sinking OTA amplifier or amplifiers driving feedback optocoupler’s LED. Connect
here compensation network (networks) as well.
3
4
5
6
7
8
ISNS
COMP
D+
Current sensing input for output current regulation, connect it to shunt resistor in ground branch.
Compensation pin of output voltage regulation, connected to a feedback compensation network.
USB D+ Data Line Input
USB D− Data Line Input
Ground
D−
GND
VCC
Supply voltage pin
www.onsemi.com
3
NCP4371
Table 2. MAXIMUM RATINGS
Ratings
Symbol
Value
Unit
V
Supply Voltage
V
CC
−0.3 to 28.0
DISCHARGE, DRIVE Input Voltage
D+, D− , COMP, ISNS Input Voltage
DISCHARGE Current
V
, V
−0.3 to V
CC
V
DISCHARGE
DRIVE
V
, V , V
, V
−0.3 to 5.5
500
V
D+
D− COMP ISNS
I
mA
mA
°C/W
°C
°C
V
DISCHARGE
DRIVE Sink Current
I
5
DRIVE
Junction to Air Thermal Resistance, SOIC8
Maximum Junction Temperature
Storage Temperature
R
160
θ
J−A_SOIC8
T
125
JMAX
T
−60 to 150
4000
200
STG
ESD Capability, Human Body Model (Note 1)
ESD Capability, Machine Model (Note 1)
ESD
HBM
ESD
V
MM
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTIS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)
Latchup Current Maximum Rating: ≤150 mA per JEDEC standard: JESD78
3. For information, please refer to our Soldering and Mounting Techniques Reference Manual, SOLDERRM/D
Table 3. ELECTRICAL CHARACTERISTICS
−40°C ≤ TJ ≤ 125°C; V = 5 V; unless otherwise noted. Typical values are at T = +25°C.
CC
J
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
SUPPLY
Minimum Operating Input Voltage
V
voltage at which current limiting OTA is
V
−
−
2.2
3.4
3.3
300
V
V
CC
CC(min)
enabled
V
V
HVDCP Logic Enable
HVDCP Logic Disable
V
CC
increasing level at which the HVDCP
V
CC(ON)
3.0
2.8
3.2
3.0
CC
commands are accepted
V
decreasing level at which the HVDCP
V
V
CC
CC
CC(OFF)
commands are stopped to be accepted
Quiescent Current
I
mA
CC
VOLTAGE CONTROL LOOP OTA
Transconductance
Sink current only
g
−
1
−
S
V
mv
Voltage Control Reference Voltage Nominal V
Sink Current Capability
=5 V
V
REFV
1.21
2.5
1.25
1.29
BUS
I
mA
kW
SINKV
Output Voltage Sense Divider
Resistor, Pull−Up
R
66
24
VSNS_UP
Output Voltage Sense Divider
Resistor, Pull−Down
R
kW
VSNS_DWN
CURRENT CONTROL LOOP OTA
Transconductance
Sink current only
g
mc
−
3
−
S
Current Control Reference Voltage Current limit A reference set−point
Current limit B reference set−point
V
10
12
18
24
29
34
40
53
14
17
22
28
33
38
44
57
18
21
26
32
37
42
48
60
mV
REFC(A)
REFC(B)
REFC(C)
REFC(D)
REFC(E)
V
V
V
V
Current limit C reference set−point
Current limit D reference set−point
Current limit E reference set−point
Current limit F reference set−point
V
REFC(F)
REFC(G)
REFC(H)
Current limit G reference set−point
V
V
Current limit H reference set−point
Sink Current Capability
I
2.5
mA
V
SINKC
HVDCP
Output Voltage Selection
Reference
V
1.8
2
2.2
SEL_REF
www.onsemi.com
4
NCP4371
Table 3. ELECTRICAL CHARACTERISTICS
−40°C ≤ TJ ≤ 125°C; V = 5 V; unless otherwise noted. Typical values are at T = +25°C.
CC
J
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
HVDCP
Data Detect Voltage
V
0.25
300
0.325
−
0.4
1500
24.8
40
V
DAT_REF
DAT_LKG
DM_DWN
DCP_DAT
Data Line Leakage Resistance
D− Pull−Down Resistance
R
R
kW
kW
W
14.25
19.53
D+ to D− Resistance During
DCP Mode
R
D+ High Glitch Filter Time
T
1
1
1.5
sec
ms
ms
ms
GLITCH_BC_
DONE
D− Low Glitch Filter Time
T
GLITCH_DM_
LOW
Output Voltage Glitch Filter Time
of HVDCP
T
20
100
40
60
GLITCH_V_
CHANGE
Glitch Filter For D+/− Pull−Up or
Down Time in HVDCP
T
200
GLITCH_
CONT_CHANGE
OUTPUT CAPACITOR DISCHARGER
Discharge Comparator OFF
Voltage
V
= 5 V, V
sensed at VCC pin
V
5.4
5.6
5.8
85
mV
mA
mA
BUS_REF
DIS(OFF)
DIS(OFF)
I
DIS(VCC)
VCC Discharge Current
Discharge current of the internal current sink
at the VCC pin
DISCHARGE Pin Maximum Sink
Current
Maximum sink current of the DISCHARGE pin
Minimum recommended external discharge
I
200
DIS(EXT)
resistor value connected from V
to DIS-
BUS
CHARGE pin is R >=100 W
DIS
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
5
NCP4371
TYPICAL CHARACTERISTICS
2.4
2.2
2.0
1.8
300
280
260
240
1.6
1.4
220
200
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
Figure 3. VCC Minimum Operating Input
Voltage, VCC(min)
Figure 4. Quiescent Current, ICC
3.6
3.4
3.2
3.0
3.6
3.4
3.2
3.0
2.8
2.6
2.8
2.6
−40 −25 −10
5
20 35 50 65 80 95 110 125
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 5. VCC HVDCP Logic Enable, VCC(ON)
Figure 6. VCC HVDCP Logic Disable, VCC(OFF)
1.5
1.4
1.3
3.0
2.8
2.6
2.4
1.2
1.1
1.0
2.2
2.0
−40 −25 −10
5
20 35 50 65 80 95 110 125
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 7. Voltage Control Reference Voltage,
VREFV
Figure 8. Voltage Control OTA Sink Current
Capability, ISINKV
www.onsemi.com
6
NCP4371
TYPICAL CHARACTERISTICS
20
18
16
14
3.0
2.8
2.6
2.4
12
10
2.2
2.0
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
Figure 9. Current Control Reference Voltage,
VREFC(A)
Figure 10. Voltage Control OTA Sink Current
Capability, ISINKC
2.2
2.1
0.40
0.36
0.32
0.28
2.0
1.9
1.8
0.24
0.20
−40 −25 −10
5
20 35 50 65 80 95 110 125
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 11. Output Voltage Selection Reference,
VSEL_REF
Figure 12. Data Detect Voltage, VDAT_REF
50
40
30
1.6
1.5
1.4
20
1.3
1.2
10
0
−40 −25 −10
5
20 35 50 65 80 95 110 125
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 13. D+ to D− Resistance During DCP
Mode, RDCP_DAT
Figure 14. D+ High Glitch Filter Time,
TGLITCH_BC_DONE
www.onsemi.com
7
NCP4371
TYPICAL CHARACTERISTICS
3.0
2.6
2.2
1.8
60
50
40
30
20
1.4
1.0
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
Figure 15. D− Low Glitch Filter,
TGLITCH_DM_LOW
Figure 16. Output Voltage Glitch Filter Time of
HVDCP, TGLITCH_V_CHANGE
200
180
160
140
6.0
5.8
5.6
5.4
120
100
5.2
5.0
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
Figure 17. Glitch Filter For D+/− Pull−Up or
Down Time in HVDCP, TGLITCH_CONT_CHANGE
Figure 18. Discharge Comparator OFF Voltage,
VDIS(OFF)
100
90
80
70
60
50
−40 −25 −10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
Figure 19. VCC Discharge Current, IDIS(VCC)
www.onsemi.com
8
NCP4371
APPLICATION INFORMATION
The NCP4371 is designed to operate as an output voltage
the unplug event is detected the decoder circuitry turns−on
an internal current sink, which discharges the output
capacitors to a safe voltage level. If the NCP4371 is set to a
Continuous mode it responds to the PD requests in a Single
request mode. It does not support Group request mode.
and current controller for USB chargers, which resides on
the secondary side of the off−line adapter. It enables to
accommodate the output voltage based on the request from
the portable device in order to optimize the battery charge
time. The NCP4371 is compatible with Qualcomm Quick
Charge 3.0 HVDCP specification. The output voltage can be
increased or decreased in discrete steps. The output current
is limited not to exceed the maximum power limit for given
output voltage level. The internal discharge switch
discharges the output capacitors to a safe voltage level in a
case of the cable unplug.
Table 4. D+ AND D− OUTPUT VOLTAGE CODING
Portable Device
HVDCP Class A
Adapter Voltage
12 V
HVDCP Class B
D+
D−
Adapter Voltage
0.6 V
3.3 V
0.6 V
3.3 V
0.6 V
0.6 V
0.6 V
3.3 V
3.3 V
GND
12 V
9 V
9 V
Continuous mode
Previous voltage
5 V
Continuous mode
Voltage Regulation
20 V
5V
The Voltage Regulation Path eliminates a need for a
voltage shunt regulator at the secondary side of the off−line
supply. The voltage on VCC pin is divided by internal
resistor divider (R
with the internal precise voltage reference V
voltage difference is amplified by
transconductance amplifier. The amplifier output current is
connected to the DRIVE pin. This DRIVE pin drives
regulation optocoupler that provides regulation of primary
, R
) and compared
DP_SEL_REF
DP_DAT_REF
VSNS_UP
VSNS_DWN
V
. The
SEL_REF
REFV
g
mV
of the
D+
V
DAT_REF
side. The internal voltage reference V
is adjustable
R
REFV
DAT_LKG
based on the command from the Portable Device compatible
with Qualcomm Quick Charge specification. The voltage
control loop compensation network shall be connected
between DRIVE and COMP pins.
D−
DM_DAT_REF
DM_SEL_REF
V
Current Regulation
DAT_REF
R
DM_DWN
The output current is sensed by the shunt resistor
R_SENSE in series with the load. Voltage drop on
R_SENSE is compared with internal precise voltage
V
SEL_REF
reference V
at ISNS transconductance amplifier input.
REFC
Voltage difference is amplified by g to output current of
mC
amplifier, connected to the DRIVE pin.
Figure 20. HVDCP D+ and D− Comparators
HVDCP Mode
HVDCP Mode – Continuous Mode
After power−up pins D+ and D− of NCP4371 are shorted
The continuous mode of operation leverages the
previously unused state in QC2.0. If the portable devices try
and utilize this mode, it applies voltages on D+ and D− per
Table 1. Assuming the HVDCP supports this mode of
operation, it will glitch filter the request as it currently does,
with impedance R
and internal reference voltage
voltage 5V. The device is in a BC1.2
DCP_DAT
V
REFV
is set to V
BUS
compatible mode. If a portable device compatible with the
Qualcomm Quick Charge specification is connected a
negotiation between HVDCP and PD is executed. Once the
negotiation is successful the NCP4371 opens D+ and D−
short connection and D− is pulled down with a RDM_DWN. The
NCP4371 enters HVDCP mode. It monitors D+ and D−
inputs. Based on the specified control patterns the internal
using T
. Before the portable device can
GLITCH_V_CHANGE
begin to increment or decrement the voltage, it must wait
before pulling D+ and D− high or
T
V_NEW_REQUEST_CONT
low. Once this time has finished, the portable device now
attempts to increment or decrement the voltage. To
increment, the portable device sends a pulse of width
voltage reference value V
is adjusted in order to
REFV
increase or decrease output voltage to the required value.
The NCP4371 is available in Class A and Class B version.
Class A allows to change the output voltage up to
T
by pulling D+ to V
and then must return D+
ACTIVE
DP_UP
to V
for T
.
DP_SRC
INACTIVE
V
BUS
= 12 V. Class B allows output voltage up to 20 V. If
www.onsemi.com
9
NCP4371
3.3 V
D+ 0.6 V
0 V
3.3 V
D−
0.6 V
0 V
HVDCP
Tglitch_cont
_change
Tglitch
Tglitch
_cont
_change
_cont
_change
Tglitch
_cont
_change
Tglitch
_cont
_change
Tactive
Tinactive
Tactive
Tinactive
PD
Tactive
−200 mV
+200 mV
VBUS
+200 mV
V
BUS
V
BUS
V
BUS
increment
request
increment
request
decrement
request
Figure 21. Continuous Mode of Operation Timing Diagram
The NCP4371 responds to the increment/decrement
request in a single request mode, i.e. the output voltage is
changed immediately with each request. For the single
request, and HVDCP recognizes a rising edge on D+ for an
increment, and falling edge on D− for a decrement, and
glitch filters this with T
period, it begins changing its output voltage by incrementing
or decrementing in a 200 mV step. The output voltage is at
. After this
GLITCH_CONT_CHANGE
its final value within T
.
V_CONT_CHANGE_SINGLE
www.onsemi.com
10
NCP4371
Power−On
Reset
V
BUS
= 5 V
Short D+/D−
open D− pull−down
START
BC over
Open D+/D−
D− pull−down
BC Done
D−initial low
5 V request
20 V request
HVDCP
Discrete
V
BUS
= 20 V
V
BUS
= 5 V
12 V request
9 V request
V
BUS
= 9 V
V
BUS
= 12 V
5 V request
unplug
HVDCP
Continuous
increment
request
decrement
request
V
BUS
= V
+ 200 mV
V
BUS
= V − 200 mV
BUS
BUS
max. 12 V/20 V for class A/B
min. 3.6 V
Figure 22. NCP4371 State Diagram
www.onsemi.com
11
NCP4371
Power Limit
Once the Power limit is defined by an R_SENSE selection
the user needs to define a maximum output current limit.
This current limit can be given by a connector or cable
maximum current rating.
The protocol decoder and the power limit logic will limit
maximum output current to keep regulation within
recommended V /I operating range. The Power Limit
out out
block adjusts V
voltage reference at the current
There are 5 current limit options available for Power
Option A and 8 current limit options for Power Option B and
C. Each power limit option corresponds to a particular
REFC
regulation loop in order to limit the maximum output current.
The NCP4371 is designed to give a user a high degree of
freedom to optimize maximum power and current limit
profile of the target application. The user can scale both –
maximum output power and maximum current limit
independently.
The NCP4371 has two constant power curves defined –
“Option A” for Class A only and “Option B” for either Class
A or Class B. Power Option C shall be used for applications
where constant power regulation is not required. If Power
Option C is selected then power limiting curve is ignored.
The applications based on Power Option C operate in
“constant current regulation mode”.
Current Control Reference Voltage (V
), which limits
REFC
the maximum output current for the selected R_SENSE
resistor. The user has to make a selection from current limit
characteristics shown in Figure 24. Each power limit curve
represents a unique device option (see Table Device
Options).
3.2
3.0
2.8
2.6
2.4
In order to scale the power limit curve for the given power
a selection of the current sense resistor has to be done. The
relation between current sense resistor and output power
limit is given by the curves in Figure 23.
2.2
2.0
1.8
1.6
1.4
1.2
E
D
30
C
B
A
25
1.0
0.8
POUT Limit Option B
20
10 11 12 13 14 15 16 17 18 19 20
P (W)
Power Option A Current Limit Selection
15
3.2
3.0
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
H
G
POUT Limit Option A
10
5
F
E
10 11 12 13 14 15 16 17 18 19 20
P (W)
D
Figure 23. RSENSE vs. POUT Limit Curve
C
B
The characteristics in the Figure 23 cover a range P
10 – 20 W. For powers outside this interval following
=
OUT
A
formula can be used for R
selection:
SENSE
1.0
0.4
168
Pmax
Option A (Class A only) :
RSENSE
+
[mW]
[mW]
(eq. 1)
(eq. 2)
10 11 12 13 14 15 16 17 18 19 20
P (W)
277
Pmax
Option B (Class A & B) :
RSENSE
+
Power Option B Current Limit Selection
Figure 24. Current Limit Characteristics
www.onsemi.com
12
NCP4371
Table 5. CURRENT LIMIT OPTION REFERENCE VOLTAGE
Current Limit Option
[mV]
A
B
C
D
E
F
G
H
V
14
17
22
28
33
38
44
57
REFC
Soft Short−Circuit Protection
Discharge
In case of a short−circuit at the USB cable end or the
portable device USB receptacle it is desired to limit the short
circuit current to prevent a portable device or cable from a
damage. The NCP4371 offers an extended region of output
If voltage level lower than actual V
is requested by PD
BUS
the discharge circuitry discharges the output capacitors to
reach the new voltage level in a short time. As well, the
discharge circuitry is activated if cable unplug event is
detected. The NCP4371 features two discharge paths. By
default, the discharge is done via built−in regulated current
source at VCC pin. If the VCC pin discharge capability is not
sufficient an external discharge resistor R
The discharge resistor is wired from a positive pole of the
output capacitor to the DISCHARGE pin. The minimum
current limiting down to V
= 2.2 V. If the V
falls
BUS
BUS
below V
then the HVDCP logic is disabled and D+/−
CC(OFF)
pins are shorted. No further commands from the portable
device are accepted. The only feature enabled is the output
current limiting at the moment. The device stays in the
has to be used.
DIS
current limiting mode until V rises back above V
CC
CC(ON)
threshold. The device logic will resume its operation and
goes to a default BC1.2 compatible mode. A new negotiation
between the charger and portable device has to be carried out
in order to enable HVDCP compatibility mode.
recommended value of the discharge resistor R
is 100 W.
DIS
The DISCHARGE pin has an internal protection for a case
the user wires the pin directly to V . If this condition is
BUS
detected the discharge MOSFET at the pin is turned off. It
is highly recommended to use an external discharge resistor
always if Class B device is used. In case of Class A device
and C
< 1500 mF the DISCHARGE pin can be left
OUT
disconnected.
Table 6. DEVICE OPTIONS
QuickCharge
Class A/B
Power Limit
Current Limit (mV)
OPN #
NCP4371___DR2G
A
B
A
B
C
A
B
C
D
E
F
G
H
Marking
Class A Class B Class A Class A&B No Power 14
Limit
17
22
28
33
38
44
57
NCP4371AACDR2G
NCP4371AAEDR2G
NCP4371AADDR2G
NCP4371ACCDR2G
NCP4371BBEDR2G
4371AAC
4371AAE
4371AAD
4371ACC
4371BBE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ORDERING INFORMATION
Device
†
Marking
Package
Shipping
NCP4371AACDR2G
NCP4371AAEDR2G
NCP4371AADDR2G
NCP4371ACCDR2G
NCP4371BBEDR2G
4371AAC
4371AAE
4371AAD
4371ACC
4371BBE
SOIC−8
Pb−Free
2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
13
NCP4371
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AK
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
−X−
A
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
8
5
4
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
S
M
M
B
0.25 (0.010)
Y
1
K
−Y−
MILLIMETERS
DIM MIN MAX
INCHES
G
MIN
MAX
0.197
0.157
0.069
0.020
A
B
C
D
G
H
J
K
M
N
S
4.80
3.80
1.35
0.33
5.00 0.189
4.00 0.150
1.75 0.053
0.51 0.013
C
N X 45
_
SEATING
PLANE
1.27 BSC
0.050 BSC
−Z−
0.10
0.19
0.40
0
0.25 0.004
0.25 0.007
1.27 0.016
0.010
0.010
0.050
8
0.020
0.244
0.10 (0.004)
M
J
H
D
8
0
_
_
_
_
0.25
5.80
0.50 0.010
6.20 0.228
M
S
S
X
0.25 (0.010)
Z
Y
SOLDERING FOOTPRINT*
1.52
0.060
7.0
4.0
0.275
0.155
0.6
0.024
1.270
0.050
mm
inches
ǒ
Ǔ
SCALE 6:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
Qualcomm Quick Charge is a trademark of Qualcomm Incorporated.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
NCP4371/D
相关型号:
©2020 ICPDF网 联系我们和版权申明