LPU-75C [PAIRUI]
Constant current LED Drivers;
| 型号： | LPU-75C |
| 厂家： | 
PAIRUI GROUP INC. |
| 描述： | Constant current LED Drivers |
| 文件： | 总8页 (文件大小：992K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Constant current LED Drivers
For outdoor use
LPU-75C Series, 75Watt
FEATURES:
ꢀ
ꢀ
ꢀ
Constant current output
Input voltage range 100-277Vac
Short circuit, over current, over voltage and over
temperature protections
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Designed to worldwide safety standards for lighting
Active power factor correction
IP67 for outdoor use
Multiple dimming
5 year warranty
Output voltage
Output power
(Vdc)
Input voltage
(Vac)
Output current
Model
(mA)
(W)
Min.
Max.
350
LPU75-C350
LPU75-C530
LPU75-C700
LPU75-C1050
LPU75-C1400
LPU75-C1750
LPU75-C2100
LPU75-C2800
LPU75-C3500
107
71
54
36
27
21
18
13
10
214
142
108
72
74.9
75.3
75.6
75.6
75.6
75.25
75.6
75.6
75.6
530
700
1050
1400
1750
2100
2800
3500
100-277
54
43
36
27
21
Note:
You may request for the models with different dimming functions, plus “D/P/T/A” in the suffix: e.g. LPU75-C350D.
Blank Without Dimming PWM Dimming Timer Dimming
0-10V or Resistor Dimming
3 in 1 Programmable Dimming
D
P
T
A
ELECTRICAL
Input
Parameters
Symbols
Test Conditions / Comment
Min.
Typ.
Max.
Units
Input Voltage
---
90
305
Vac
Vin
Input Frequency
---
47
--
63
Hz
A
Fline
0.93
0.42
0.35
Full load,
Full load,
Full load,
V
V
V
in=100Vac
in=220Vac
in=277Vac
Input current
--
--
Iin
Inrush Current
--
50
A
V
Cold Start, in =230Vac
Iinrush
www.pairuigroup.com
Page: 1 / 8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-75C Series, 75Watt
ELECTRICAL
Input
Parameters
Symbols
Test Conditions / Comment
Min.
0.98
0.95
0.90
Typ.
Max.
Units
70% ~100% Load,
70% ~100% Load,
70% ~100% Load,
70% ~100% Load,
70% ~100% Load,
70% ~100% Load,
V
V
V
V
V
V
in =100Vac
in =220Vac
in =277Vac
in =100Vac
in =220Vac
in =277Vac
Power Factor
--
--
PF
PF
10
20
25
Total Harmonic
Distortion
--
--
%
THD
Efficiency
Full voltage, full load
85
--
88
--
91
%
η
Leakage Current
0.5
mA
V
in=277Vac/ 60Hz
Ileakage
Output
LPU75-C350
LPU75-C530
LPU75-C700
LPU75-C1050
LPU75-C1400
LPU75-C1750
LPU75-C2100
LPU75-C2800
LPU75-C3500
LPU75-C350
LPU75-C530
332
503
350
530
700
1050
1400
1750
2100
2800
3500
--
368
557
mA
mA
mA
mA
mA
mA
mA
mA
mA
V
665
735
997
1102
1470
1837
2205
2940
3675
214
Output Current
1330
1663
1995
2660
3325
107
Iout
71
--
142
V
LPU75-C700
LPU75-C1050
LPU75-C1400
LPU75-C1750
LPU75-C2100
LPU75-C2800
LPU75-C3500
54
36
27
22
18
14
11
--
--
--
--
--
--
--
108
72
54
43
36
27
21
V
V
V
V
V
V
V
Output Voltage
Vout
Line Regulation
Load Regulation
--
--
--
--
--
1
1
1
%
%
S
Iout-line
Iout-load
Ton_delay
Vin from 100Vac to 277Vac
Vout from min. To max.
Cold Start, Power ON
Turn-On Delay Time
1.5
www.pairuigroup.com
Page: 2 / 8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-75C Series, 75Watt
ELECTRICAL
Output
Parameters
Symbols
Test Conditions / Comment
Min.
Typ.
Max.
Units
Ripple Current
Full Load, (pk-to-pk)/Average
--
--
20
%
Iout-ripple
Output Current
Overshoot
Turning Power ON
--
--
10
%
Iovershoot
+12V Auxiliary Output (Optional)
12V Output Voltage
12V Output Current
Auxiliary Power
11
0
12
--
13
100
1.2
V
VAUX
IAUX
A +12V auxiliary output provides
power for active LED cooler or
other active equipment.
mA
W
--
--
PAUX
0-10V or Resistor Dimming
The 0-10V or resistor dimming is a dimming manner that can be used to dim the output current via a standard commercial
wall dimmer (0-10Vdc or 1-10Vdc) or an external control voltage source (0-10Vdc or 1-10Vdc) or external resistor.
ꢁ
The dimming range is 100% Iout to 5%
DIM is 1V, the output current is 5% Iout.
When VDIM below 0.7V, the driver will shut down and it will recovery when VDIM goes above 1V.
I
out. When
V
DIM is 9-10Vdc, the output current maintains 100%
I
out, and when
V
ꢁ
See “0-10V Dimming Curve” for detailed information.
Absolute Maximum
---
---
---
-2
50
9
--
75
--
15
100
--
V
μA
V
VDIM
Voltage on 0-10V Pin
Source Current on 0-10V
IDIM
Dimming Pin
V
DIM Voltage
VDIM-MAX
IOUT-MIN
for Full Bright
Minimum Output
Current
--
5%
--
VDIM=1V
% of Iout
V
DIM Voltage When the
Driver Shut Down
---
0.6
0.9
--
0.7
1
0.8
1.1
--
V
VDIM-SHUT
V
DIM Voltage When the
Driver Recovery after
Shut Down
---
V
VDIM-recovery
External Resistor Value
at Full Bright
See “External Resistor Dimming
Curve (D Type)” for details
120
KΩ
RExternal-MAX
www.pairuigroup.com
Page: 3 / 8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-75C Series, 75Watt
ELECTRICAL
PWM Dimming
The PWM dimming is a dimming manner that can be used to dim the output current via the duty cycle of PWM signal.
ꢁ
ꢁ
The dimming range is 100% Iout to 5% Iout. When the duty cycle is 100%, the output current reaches 100% Iout, and the
output current maintains 5% Iout . when the duty cycle below 5%.
When the PWM signal is low the driver will shut down and it will recovery when the duty cycle goes above 5%.
See “PWM Dimming Curve” for detailed information.
Parameters
Symbols
Test Conditions / Comment
Min.
Typ.
Max.
Units
PWM Frequency
---
0.1
--
2
KHz
FPWM
High Level Voltage of
PWM Signal
---
---
4
0
--
--
--
5
12
1
V
V
VPWM-High
VPWM-Low
IOUT-MIN
Lower Level Voltage of
PWM Signal
Minimum Output
Current
When duty cycle below 5%
--
% of Iout
Timer Dimming
The Timer Dimming is designed with time controlled dimming function, it will dim to 50% of rated output current after
operating six hours.
See “ T Type Dimming Curve” for detailed information.
Note1: The dimming time and
Full Load Operated Time
Dim Output Current
5.5
45
6
6.5
55
Hrs
TFULL-LOAD-TTYPE
dimming current can be customized
Note2: Timing shut down function
can be customized
50
IOUT-MIN-TTYPE
% of Iout
LED Board Temperature Detection(Optional)
The LED board temperature detection input can be connected to a thermistor (NTC) to realize a LED Board Over
Temperature Protection and prevent the LED lamp from damage or luminous decay at high temperature.
The thermistor should be located on the LED assembly to monitor its temperature. If the temperature exceeds the
predetermined LED OTP point, the output current of the driver is automatically reduced to regulate the temperature of the
LED board at a safe level.
See “LED OTP Current Reduction Curve” for detailed information.
Thermistor Resistance
Value that Start Current
Reduction
When the thermistor resistance
less than this value the output
current start reduce.
--
4
--
KΩ
RLEDOTP
Protection
Over Voltage
---
--
110% 150%
VOVP
Vout
Short Circuit
Hiccup mode, it will recover automatically after fault conditions are removed.
Page: 4 / 8
www.pairuigroup.com
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-75C Series, 75Watt
ELECTRICAL
Protection
Parameters
Symbols
Test Conditions / Comment
Min.
Typ
Max
Units
If the temperature exceeds OTP
point, the output current of the
driver is automatically reduced.
Over Temperature
90
95
100
TOTP
Environment
Storage Temperature
Humidity: 5% RH to 95% RH
-40
-40
--
--
--
+85
+70
+90
95
--
Tstorage
Ta
Ambient Operating
Temperature
Startup at rated voltage
Hot-spot on case
Maximum Case
Temperature
--
TC
Operating Relative
Humidity
Non condensing
10
50
200
--
--
%
kHrs
kHrs
g
Ha
Full load, case temperature 55
Life Time
MTBF
--
TLife
TMTBF
WNBT
Full load, 220Vac input,
--
--
25 ambient temperature
Net Weight
---
650
--
Dimension(LxWxH)
167 x 70 x 34mm
EMC Compliance
EN55015
EN61000-3-2 Class C
EN61000-3-3
FCC Part 15 Class B
EN61547
Conducted Emission & Radiated Emission
Harmonic Current Emission
Voltage fluctuation and flicker
Conducted and Radiated Emission Measurement
Equipment for general lighting purposes: EMC Immunity Requirements
Electrostatic Discharge (ESD). Air Discharge: 15kV; Contact Discharge: 8kV
Radiated Radio-Frequency electromagnetic field
Electrical Fast Transient / burst
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11
Surge Immunity Test: L-N 6KV, L/N-GND 6KV
Conducted disturbances induced by Radio-Frequency fields
Power Frequency Magnetic Field Test
Voltage Dips, short interruptions and Voltage Variations
Note: Unless otherwise specified, all the above parameters are measured at ambient temperature of 25
= 100Vac to 277Vac.
and Vin
www.pairuigroup.com
Page: 5 / 8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-75C Series, 75Watt
ELECTRICAL
TYPICAL APPLICATION
Timer Dimming
LPU-75C
Series
Versatile control features:
ꢁ
ꢁ
ꢁ
ꢁ
A Temperature sensor(NTC thermistor) protects the LED from over temperature;
12V/100mA Auxiliary output can be used to power auxiliary loads such as active cooler or external dimming controller;
Accepts various manner to dim the output current and the dimming range is 5% to 100%Iout;
Support shut down functions at dimming applications.
TYPICAL CHARACTERISTICS CURVE
Power Factor VS. Load
Efficiency VS. Load
www.pairuigroup.com
Page: 6 / 8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-75C Series, 75Watt
TYPICAL CHARACTERISTICS CURVE
Output Current VS. Dimming Voltage Output Current VS. External Resistor
Output current VS. Duty Cycle of PWM Signal
Output Current VS. Running Time
Current Reduction VS. Thermistor Resistance Value
www.pairuigroup.com
Page: 7 / 8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-75C Series, 75Watt
MECHANICAL
No Dimming & Timer Dimming Version
Unit: mm
0~10Vdc or Resistor Dimming & PWM Dimming Version
Unit: mm
www.pairuigroup.com
Page: 8 / 8
Date: 04/29/2014
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明