2R5TAE220M [PANASONIC]

Conductive Polymer Tantalum Solid Capacitors;


型号：	2R5TAE220M
厂家：	PANASONIC
描述：	Conductive Polymer Tantalum Solid Capacitors
文件：	总6页 (文件大小：490K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Conductive Polymer Tantalum

Solid Capacitors

Surface Mount Type

TA series

■ This product is not intended for use in any driving application or any other critical functions that affect passenger safety.(e.g. Powertrain, ABS, Engine ECU, Airbag, etc.)

If the intended use of TA/TV series products is for use in other automotive related applications, please contact our sales team. All requests are subject to approval.

Features

● Guaranteed at 85 ℃ 85 %RH

● RoHS compliance, Halogen free

Specifications

Size code

D2E

D3L

Category temp. range

Rated volt. range

Category volt. range

Rated cap. range

–55 ℃ to +105 ℃

4.0 V to 10 V

47 μF to 100 μF

2.5 V to 10 V

68 μF to 470 μF

150 μF to 680 μF

Capacitance tolerance

Leakage current

Dissipation factor(tan δ)

Surge voltage (V)

±20 % (120 Hz / +20 ℃)

Please see the attached characteristics list

Rated voltage × 1.15

+105 ℃ 2000 h (B2 size : 1000 h) , rated voltage applied

Capacitance change Within ±20 % of the initial value

Dissipation factor(tan δ) ≦ 1.5 times of the initial limit

Leakage current Within the initial limit

+85 ℃, 85 % to 90 %, 500 h, rated voltage applied

Within +50 %, −20 % of the initial value

Endurance

Capacitance change

(2R5TAE470M (F), 2R5TAE330M (I, F), 2R5TAE220M (F, 9))

Within +40 %, −20 % of the initial value (Except for above model)

Damp heat

(Steady State)

Dissipation factor(tan δ) ≦ 1.5 times of the initial limit

Leakage current Within the initial limit

Marking

Dimensions (not to scale)

＜ B2 size ＞

＜ D2E, D3L size ＞

Rated capacitance (μF)

Rated capacitance code

Polarity marking (+)

Rated voltage code

Lot. No.

Rated voltage code

Lot. No.

R. voltage code

Unit：V

2.5

6.3

Unit：ｍｍ

W1±0.1

Size code

W±0.2

S±0.2

D2E

D3L

3.5±0.2 2.8 1.9±0.1 0.8

7.3±0.3 4.3 1.8±0.1 1.3

7.3±0.3 4.3 2.8±0.2 1.3

2.2

2.4

＜ B2 size ＞

R. capacitance code

Unit：μF

100

* Externals of figure are the reference.

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

18-Jun-18

Conductive Polymer Tantalum Solid Capacitors

TA series

Characteristics list

Case size

（ｍｍ）

Floor life

level

Specifications

Standard

Cate-

Rated

temper- gory

ature voltage

Cate-

Rated

capaci-

tance

(μF)

Rated

voltage

(V)

gory

temper-

ature

Size

code

Min.

packaging

q'ty

Ripple^*1

current

(mA rms)

Reflow Reflow

LC^*4

(μA)

ESR^*2

tan δ^*3

(mΩ max.)

temp

Part number

(℃)

(V)

≦260℃ ≦250℃

(℃)

(pcs)

105

2.5

4.0

6.3

105

7.3 4.3 1.8

3900

3100

2400

3100

2800

2400

3100

2400

3100

2400

0.10 110.0 2R5TAE220M9

3000

2500

2000

3000

2500

2000

3000

2500

2000

3000

2500

220 7.3 4.3 1.8

7.3 4.3 1.8

0.10 55.0

0.10 82.5

2R5TAE220MF

2R5TAE220M

2R5TAE330MF

2R5TAE330MI

2R5TAE330M

7.3 4.3 1.8

D2E

330 7.3 4.3 1.8

7.3 4.3 1.8

2.5

7.3 4.3 1.8

470

0.10 117.5 2R5TAE470MF

0.10 117.5 2R5TAE470M

0.10 170.0 2R5TAE680MFL

0.10 170.0 2R5TAE680ML

7.3 4.3 1.8

7.3 4.3 2.8

680

D3L

7.3 4.3 2.8

100 3.8 2.8 1.9 B2 1100

0.08 40.0

0.10 88.0

4TAB100M

4TAE220MI

4TAE220M

7.3 4.3 1.8

7.3 4.3 2.8

2800

2400

2800

2400

1100

2400

220

470

D2E

D3L

4.0

0.10 188.0 4TAE470MIL

0.10 188.0 4TAE470ML

47 3.5 2.8 1.9

68 3.5 2.8 1.9

150 7.3 4.3 1.8

0.08 29.6

0.08 42.8

0.10 94.5

6TAB47M

6TAB68M

6TAE150M

6.3

7.3 4.3 1.8 D2E 2800

7.3 4.3 1.8 2400

0.10 138.6 6TAE220MI

0.10 138.6 6TAE220M

0.10 207.9 6TAE330ML

220

330 7.3 4.3 2.8 D3L 2400

47 3.5 2.8 1.9 B2 1100

68 7.3 4.3 1.8 D2E 2400

0.08 47.0

0.10 68.0

10TAB47M

10TAE68M

150 7.3 4.3 2.8

220 7.3 4.3 2.8

2400

0.10 150.0 10TAE150ML

0.10 220.0 10TAE220ML

D3L

*1: Ripple current（100 kHz / +45 ℃）

*2: ESR（100 kHz / +20 ℃）ꢀ

*3: tan δ (120 Hz / +20 ℃)

*4: After 5 minutes

◆ Please refer to each page in this catarog for “Reflow conditions” ,“Taping specifications” and "Floor life level" .

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

18-Jun-18

Guidelines and precautions regarding the

technical information and use of our products

described in this online catalog.

■ If you want to use our products described in this online catalog for applications requiring

special qualities or reliability, or for applications where the failure or malfunction of the

products may directly jeopardize human life or potentially cause personal injury

(e.g. aircraft and aerospace equipment, traffic and transportation equipment, combustion

equipment, medical equipment, accident prevention, anti-crime equipment, and/or safety

equipment), it is necessary to verify whether the specifications of our products fit to such

applications. Please ensure that you will ask and check with our inquiry desk as to whether

the specifications of our products fit to such applications use before you use our products.

■ The quality and performance of our products as described in this online catalog only apply

to our products when used in isolation. Therefore, please ensure you evaluate and verify

our products under the specific circumstances in which our products are assembled in your

own products and in which our products will actually be used.

■ If you use our products in equipment that requires a high degree of reliability, regardless

of the application, it is recommended that you set up protection circuits and redundancy

circuits in order to ensure safety of your equipment.

■ The products and product specifications described in this online catalog are subject to

change for improvement without prior notice. Therefore, please be sure to request and

confirm the latest product specifications which explain the specifications of our products in

detail, before you finalize the design of your applications, purchase, or use our products.

■ The technical information in this online catalog provides examples of our products'

typical operations and application circuits. We do not guarantee the non-infringement of

third party's intellectual property rights and we do not grant any license, right, or interest

in our intellectual property.

■ If any of our products, product specifications and/or technical information in this online

catalog is to be exported or provided to non-residents, the laws and regulations of the

exporting country, especially with regard to security and export control, shall be observed.

<Regarding the Certificate of Compliance with

the EU RoHS Directive/REACH Regulations>

■ The switchover date for compliance with the RoHS Directive/REACH Regulations varies

depending on the part number or series of our products.

■ When you use the inventory of our products for which it is unclear whether those products

are compliant with the RoHS Directive/REACH Regulation, please select "Sales Inquiry" in the

website inquiry form and contact us.

We do not take any responsibility for the use of our products outside the scope of the

specifications, descriptions, guidelines and precautions described in this online catalog.

01-Oct-19

Notices / Items to be observed

Notices

■ Applicable laws and regulations

・This product complies with the RoHS Directive (Restriction of the use of certain hazardous substances in

electrical and electronic equipment (DIRECTIVE 2011/65/EU and（EU)2015/863)).

・ No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in

producing this product.

ꢀWe do not use PBBs or PBDEs as brominated flame retardants.

・ Export procedure which followed export related regulations, such as foreign exchange and a foreign trade

method, on the occasion of export of this product.

・ These products are not dangerous goods on the transportation as identified by UN(United Nations) numbers

or UN classification.

■ Limited applications

・ This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home

appliances, computers and other office equipment, optical equipment, measuring equipment.

・ High reliability and safety are required [ be / a possibility that incorrect operation of this product may do harm

ꢀto a human life or property ] more. When use is considered by the use, the delivery specifications which suited

the use separately need to be exchanged.

■ Intellectual property rights and licenses

・ The technical information in this specification provides examples of our products' typical operations and application

circuits. We do not guarantee the non-infringement of third party's intellectual property rights and we do not grant

any license, right, or interest in our intellectual property.

Items to be observed

■ For specification

・ This specification guarantees the quality and performance of the product as individual components.

The durability differs depending on the environment and the conditions of usage.

Before use, check and evaluate their compatibility with actual conditions when installed in the products.

When safety requirements cannot be satisfied in your technical examination, inform us immediately.

・ Do not use the products beyond the specifications described in this document.

■ Upon application to products where safety is regarded as important

Install the following systems for a failsafe design to ensure safety if these products are to be used in

equipment where a defect in these products may cause the loss of human life or other signification damage,

such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment,

electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime

prevention equipment.

(1) The system is equipped with a protection circuit and protection device.

(2) The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event

of a single fault.

■ Conditions of use

・ Before using the products, carefully check the effects on their quality and performance, and determined

ꢀwhether or not they can be used. These products are designed and manufactured for general-purpose and

ꢀstandard use in general electronic equipment. These products are not intended for use in the following special

ꢀconditions.

(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent.

(2) In direct sunlight, outdoors, or in dust.

(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a

high concentration corrosive gas, such as Cl2, H2S, NH3, SO², or NOx.

(4) In an environment where strong static electricity or electromagnetic waves exist.

(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near

these products.

(6) Sealing or coating of these products or a printed circuit board on which these products are mounted,

with resin and other material.

(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular,

when using water or a water-soluble cleaning agent, be careful not to leave water residues)

(8) Using in the atmosphere where strays acid or alkaline.

(9) Using in the atmosphere where there are excessive vibration and shock.

(10) Using in the atmosphere where there are low pressure or decompression.

・ Please arrange circuit design for preventing impulse or transitional voltage.

ꢀDo not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage,

ꢀinstantaneous high voltage, high pulse voltage etc.

・ Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid

ꢀdeterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and

affects performance, characteristics, and functions of customer system.

01-Oct-19

Conductive Polymer Tantalum Solid Capacitors

ꢀꢀGuidelines and precautions（POSCAP）

1. Circuit design

1.1 Prohibited circuits

Since problems can be expected, POSCAP cannot be used on the following circuits.

(1) High impedance voltage retention circuits

(2) Coupling circuit

(3) Time constant circuits

(4) Circuits greatly affected by leakage current

(5) The circuit in which two or more POSCAP are connected in a series so as to raise the endurance voltage.

1.2 Failure and life-span

The failure rate is 0.5 %* / 1000 h (Confidence level : 60 %) based on JIS C 5003.

The mainly failure modes are as follows.

* B2 size or less : 1.0 %

1.2-1 Contingency failure

The main causes of failure are thermal stresses cause by the soldering or thermal use environment, along

with heat stresses, electrical stresses or mechanical stresses. The most common failure mode is a short

circuit. In case a short circuit occurs, ensure safety by fully considering the followings.

(a) If POSCAP emit smoke, turn off the main power of the equipment. In this case, keep your face and

hands away from the area.

(b) It may take a few seconds to a few minutes before POSCAP emits smoke by the situation. Increase

safety by using a protective circuit.

(d) In case a large current continues to flow after a short circuit, in the worst case, the shorted-out

section may ignite. For safety, install a redundant circuit or a protective circuit, etc.

1.2-2 Wear-out failure (lifetime)

When lifetime exceeded the specified guarantee time of Endurance and Damp heat, electrolyte might

insulate and cause electric characteristic changed. This is called an open circuit. The rated capacitance

values and the electrical characteristics values such as ESR specified in the characteristics list are factory

default values. Please carefully design a circuit since rated capacitance values and the electrical

characteristics values may change (increase) beyond the specified values under the conditions of rated

voltage/temperature and electrical/mechanical performances.

1.3 Reduction of failure stress

When POSCAP is used within the rated voltage, it shows a stable characteristic, but it may be damaged

in a short circuit when an overvoltage, for instance, is applied. The time to reach the failure mode can be

extended by using POSCAP with reduced environment temperature, ripple current and applied voltage.

Failure rate

・ In the case of the endurance which is 105 °C 2000 h.

0.5 %/1000 h (Environment temp. : 105 °C, Rated voltage or Category voltage applied)

・ In the case of the endurance which is 105 °C 1000 h or 125 °C 1000 h.

1.0 %/1000 h (Environment temp. : 105 °C, Rated voltage or Category voltage applied)

・ In the case of the endurance which is 85 °C 1000 h.

1.0 %/1000 h (Environment temp. : 85 °C, Rated voltage applied)

1.4 Check the rated performance

After checking the operation and installation environments, design the circuit so that it falls within the rated

performance range stipulated in this delivery specification.

1.5 Operating temperature and ripple current

(1) Set the operating temperature so that it falls within the range stipulated in this delivery specification.

(2) Do not apply current that exceeds the allowable ripple current. Ripple current should be controlled so that

ꢀsurface temperature of a capacitor do not exceed the rated temperature.

(For questions regarding TQC series, please contact us.)

(3) The ESR values specified in the characteristics list are factory default values.ꢀ

ESR values may change (increase) beyond the specified values depending on the customer's use conditions.

11-Mar-20

Conductive Polymer Tantalum Solid Capacitors

1.6 Leakage current

Even when the soldering conditions fall within the range of this delivery specifications, leakage current

increases a little on occasion. It also increases a little during high temperature storage, high humidity storage

こand temperature cycling with no voltage applied. In cases such as these, leakage current will decrease by

applying voltage under the condition of below the POSCAP's maximum operating temperature.

The speed at which the leakage current is restored is increased by applying voltage when the POSCAP's

temperature is close to the maximum operating temperature.

1.7 Rapid charge and discharge limitation

Rapid charge and discharge are restricted (for maintainance of high-proof reliability).

A protective circuit is recommended for when a rapid charge or discharge causes excessive rush current

since this is main cause of short circuit and large leakage current. Use a protective circuits in case the rush

current value exceeds 20 A*.

Be sure to insert a protection resistor of about 1 kΩ for charge and discharge when measuring the leakage

current.

* When TH series use under the ambient temperature more than 105 °C : 10 A, TPU series : 10 A

2. Mounting

2.1 Protect circuit

The failure mode of POSCAP is the short mode. When it breaks down, short electric current flows to it.

POSCAP gives off heat by this short current.

Do the following consideration in design fully for the safety because it has a bad influence on the part around

POSCAP due to this heat.

・ A protective circuit and a protective device are set up, so as to make the system safer.

・ A diffuse circuit and so on is set up, so as to make the system safer such as that a machine may not

break down as to the single trouble.

2.2 Considerations when soldering

The soldering conditions are to be within the range prescribed in this delivery specification.

If the specifications are not followed, there is the possibility of degradation of electric characteristic and

lifetime when soldering is conducted under conditions that are harsher that those stipulated.

2.3 Others

POSCAP’s Electrical characteristics are affected by temperature and frequency fluctuations.

Design circuits after checking the amount of fluctuation.

3. Storage

It is necessary to set an environment to prevent a trouble at the time of soldering by the degradation of solder

ability or moisture's getting into the molding resin when POSCAP are stored.

● Please make storage of POSCAP sealing up in the reel and storage bag at the time of delivery in the following

environment. Also, set storage period of unopened as 18 months or shorter after shipment from factory.

・ Room temperature and room humidity (generally : 15 to 35 °C, 45 to 75% RH ) are desirable.

・ Place where POSCAP is not exposed by direct sunshine.

● Please unseal storage bag just before mounting and use up POSCAP in the storage bag.

Floor life

Level

Time

Conditions

4 weeks

168 hours

48 hours

≦ 30 ℃ / 60 %Rh

POSCAP is not compatible with JEDEC J-STD-020, J-STD-033

✽ Intellectual property right

We, Panasonic Group are providing the product and service that customers can use without anxiety, and are

working positively on the protection of our products under intellectual property rights.

Representative patents relating to POSCAP are as follows:

US Patent ꢀ No.6508800, No.6891717, No.7158368, No.7326260号, No.8081421, No.8149569,

No.8456804, No.8559166

11-Mar-20

2R5TAE220M [PANASONIC]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E