AN78M07F [PANASONIC]

3-pin Positive Output Voltage Regulators 500mA Type; 3针正输出电压调节器500毫安类型


型号：	AN78M07F
厂家：	PANASONIC
描述：	3-pin Positive Output Voltage Regulators 500mA Type 3针正输出电压调节器500毫安类型线性稳压器IC 调节器电源电路输出元件局域网
文件：	总9页 (文件大小：72K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AN78M00/AN78M00F Series

3-pin Positive Output Voltage Regulators (500mA Type)

■ Overview

AN78M00 Series

Unit:mm

1.4±0.1

The AN78M00 and the AN78M00F series are 3-pin

10.5±0.5

10.4±0.5

ø3.7

fixed positive output voltage regulators. Stabilized fixed

output voltage is obtained from unstable DC input volt-

age without using any external components. 11 types of

fixed output voltage are available;5V, 6V, 7V, 8V, 9V, 10V,

12V, 15V, 18V, 20V and 24V. They can be used widely in

power circuits with current capacitance up to 500mA.

1.4±0.25

0.8±0.2

+0.1

– 0.05

2.54

0.45

2.5±0.25

■Features

4.5±0.3

1:Input

2:Common

3:Output

• No external components

• Output voltage:5V, 6V, 7V, 8V, 9V, 10V, 12V,

15V, 18V, 20V, 24V

JEDEC:TO-220AB (HSIP003-P-0000)

• Short-circuit current limiting built-in

• Thermal overload protection built-in

• Output transistor safe area compensation

AN78M00F Series

Unit:mm

10.5±0.3

2.77±0.3

(1.73)

ø5.3

(4.3)

ø3.1±0.1

+0.1

– 0.05

0.4

1.4±0.2

0.8±0.2

(0.4)

2.0±0.25

2.5±0.25

2.54

1:Input

2:Common

3:Output

4.5±0.3

TO-220 Full Pack Package (HSIP003-P-0000A)

■Block Diagram

Input

Pass Tr

Q₁

Current

Source

Current

Limiter

R_SC

Output

R₂

R₁

Voltage

Reference

Starter

Thermal

Protection

Error Amp.

–

Common

■ Absolute Maximum Ratings (Ta=25˚C)

Parameter

Symbol

Rating

Unit

Input voltage

V_I

P_D

AN7800 Series

AN7800F Series

Power dissipation

10.25

Operating ambient temperature

Storage temperature

T_opr

T_stg

–20 to +80

˚C

–55 to +150

AN78M05/F, AN78M06/F, AN78M07/F, AN78M08/F, AN78M09/F, AN78M10/F, AN78M12/F, AN78M15/F, AN78M18/F

AN78M20/F, AN78M24/F

Follow the derating curve. When T_jexceeds 150˚C, the internal circuit cuts off the output.

■ Electrical Characteristics (Ta=25˚C)

AN78M05/78M05F (5V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

4.8

4.75

typ

max

5.2

Unit

T_j=25˚C

V_I=7.5 to 20V, I_O=5 to 350mA,

Output voltage tolerance

Line regulation

V_O

5.25

T_j=25˚C, P_D

V_I=7.5 to 25V, T_j=25˚C

V_I=8 to 25V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

100

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=8 to 25V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

Ripple rejection ratio

V_I=8 to 18V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

300

T_j=25˚C

700

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

– 0.5

mV/˚C

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=10V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

■ Electrical Characteristics (Ta=25˚C)

AN78M06/78M06F (6V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

typ

max

6.25

Unit

T_j=25˚C

V_I=8.5 to 21V, I_O=5 to 350mA,

5.75

Output voltage tolerance

Line regulation

V_O

5.7

6.3

T_j=25˚C, P_D

V_I=8.5 to 25V, T_j=25˚C

V_I=9 to 25V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

1.5

120

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=9 to 25V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

Ripple rejection ratio

V_I=9 to 19V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

300

mV/˚C

T_j=25˚C

700

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

– 0.5

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=11V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

AN78M07/78M07F (7V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

6.7

6.65

typ

max

7.3

Unit

T_j=25˚C

V_I=9.5 to 22V, I_O=5 to 350mA,

Output voltage tolerance

Line regulation

V_O

7.35

< *

T_j=25˚C, P_D

V_I=9.5 to 25V, T_j=25˚C

V_I=10 to 25V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

140

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=10 to 25V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

Ripple rejection ratio

V_I=10 to 20V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

300

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

mV/˚C

T_j=25˚C

700

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

– 0.5

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=12V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

■ Electrical Characteristics (Ta=25˚C)

AN78M08/78M08F (8V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

7.7

7.6

typ

max

8.3

Unit

T_j=25˚C

V_I=10.5 to 23V, I_O=5 to 350mA,

Output voltage tolerance

Line regulation

V_O

8.4

T_j=25˚C, P_D

V_I=10.5 to 25V, T_j=25˚C

V_I=11 to 25V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

160

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

4.1

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=10.5 to 25V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

Ripple rejection ratio

V_I=11.5 to 21.5V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

300

mV/˚C

T_j=25˚C

700

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

– 0.5

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=14V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

AN78M09/78M09F (9V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

typ

max

9.35

Unit

T_j=25˚C

V_I=11.5 to 24V, I_O=5 to 350mA,

8.65

Output voltage tolerance

Line regulation

V_O

8.55

9.45

T_j=25˚C, P_D

V_I=11.5 to 25V, T_j=25˚C

V_I=12 to 25V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

180

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

4.1

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=12 to 25V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

Ripple rejection ratio

V_I=12 to 22V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

300

mV/˚C

T_j=25˚C

700

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

– 0.5

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=15V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

■ Electrical Characteristics (Ta=25˚C)

AN78M10/78M10F (10V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

9.6

9.5

typ

max

10.4

Unit

T_j=25˚C

V_I=12.5 to 25V, I_O=5 to 350mA,

Output voltage tolerance

Line regulation

V_O

10.5

T_j=25˚C, P_D

V_I=12.5 to 30V, T_j=25˚C

V_I=13 to 25V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

4.1

200

100

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=13 to 25V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

Ripple rejection ratio

V_I=13 to 23V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

300

mV/˚C

T_j=25˚C

700

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

– 0.5

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=16V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

AN78M12/78M12F (12V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

typ

max

12.5

Unit

T_j=25˚C

V_I=14.5 to 27V, I_O=5 to 350mA,

11.5

Output voltage tolerance

Line regulation

V_O

11.4

12.6

T_j=25˚C, P_D

V_I=14.5 to 30V, T_j=25˚C

V_I=16 to 30V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

4.3

240

120

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=14.5 to 30V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

Ripple rejection ratio

V_I=15 to 25V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak cutput current

300

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

mV/˚C

T_j=25˚C

700

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

– 0.8

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=19V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

■ Electrical Characteristics (Ta=25˚C)

AN78M15/78M15F (15V Type)

Parameter

Output voltage

Symbol

Condition

min

typ

max

15.6

Unit

V_O

T_j=25˚C

V_I=17.5 to 30V, I_O=5 to 350mA,

14.4

Output voltage tolerance

Line regulation

14.25

15.75

T_j=25˚C, P_D

V_I=17.5 to 30V, T_j=25˚C

V_I=20 to 30V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

REG_L

4.3

300

150

Load regulation

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=17.5 to 30V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

Ripple rejection ratio

V_I=18.5 to 28.5V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

300

700

–1

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

mV/˚C

T_j=25˚C

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=23V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

AN78M18/78M18F (18V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

typ

max

18.7

Unit

T_j=25˚C

V_I=21 to 33V, I_O=5 to 350mA,

17.3

Output voltage tolerance

Line regulation

V_O

17.1

18.9

T_j=25˚C, P_D

V_I=21 to 33V, T_j=25˚C

V_I=22 to 33V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

4.4

360

180

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=21 to 33V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

100

Ripple rejection ratio

V_I=22 to 32V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

300

700

–1.0

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

mV/˚C

T_j=25˚C

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=27V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

■ Electrical Characteristics (Ta=25˚C)

AN78M20/78M20F (20V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

typ

max

20.8

Unit

T_j=25˚C

V_I=23 to 35V, I_O=5 to 350mA,

19.2

Output voltage tolerance

Line regulation

V_O

T_j=25˚C, P_D

V_I=23 to 35V, T_j=25˚C

V_I=24 to 35V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

4.4

400

200

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=23 to 35V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

110

Ripple rejection ratio

V_I=24 to 34V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

300

700

–1.0

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

mV/˚C

T_j=25˚C

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=29V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

AN78M24/78M24F (24V Type)

Parameter

Output voltage

Symbol

V_O

Condition

min

22.8

typ

max

Unit

T_j=25˚C

V_I=27 to 38V, I_O=5 to 350mA,

Output voltage tolerance

Line regulation

V_O

25.2

T_j=25˚C, P_D

V_I=27 to 38V, T_j=25˚C

V_I=28 to 38V, T_j=25˚C

I_O=5 to 500mA, T_j=25˚C

I_O=5 to 200mA, T_j=25˚C

T_j=25˚C

100

µV

REG_IN

4.5

480

240

Load regulation

REG_L

Bias current

I_bias

∆I_{bias (IN)}

∆I_{bias (L)}

V_no

Input bias current fluctuation

Load bias current fluctuation

Output noise voltage

V_I=27 to 38V, T_j=25˚C

I_O=5 to 350mA, T_j=25˚C

f=10Hz to 100kHz

0.8

0.5

170

Ripple rejection ratio

V_I=28 to 38V, I_O=100mA, f=120Hz

I_O=500mA, T_j=25˚C

V_I=35V, T_j=25˚C

Minimum input/output voltage difference

Output short circuit current

Peak output current

300

700

–1.2

V_{DIF (min.)}

I_{O (Short)}

I_{O (Peak)}

∆V_O/Ta

mV/˚C

T_j=25˚C

Output voltage temperature coefficient

I_O=5mA, T_j=0 to 125˚C

Note 1) The specified condition T_j=25˚C means that the test should be carried out with the test time so short (within 10ms) that the

drift in characteristic value due to the rise in chip junction temperature can be ignored.

Note 2) When not specified, V_I=33V, I_O=350mA, C_I=0.33µF and C_O=0.1µF.

AN78M00 Series:15W, AN78M00F Series:10.25W

■Characteristic Curve

P_D–Ta (AN78M00 Series)

P_D–Ta (AN78M00F Series)

V_{DIF (min.)}–T_j

2.5

2.0

1.5

1.0

0.5

(1) Infinite Heat Sink

(2) 5˚C/W Heat Sink

(3) 15˚C/W Heat Sink

(4) Without Heat

Sink

(1) Infinite Heat Sink

(2) 5˚C/W Heat Sink

(3) 15˚C/W Heat Sink

(4) Without Heat Sink

AN78M05

(1)

I_O=500mA

(1)

(2)

200mA

100mA

10mA

0mA

(3)

(4)

(3)

(4)

120

160

120

160

–50

100

150

Ambient Temperature Ta (˚C)

Junction Temperature T_j(˚C)

Input Transient Response

Load Transient Response

Current Limiting

AN78M05

V_I=10V

V_O=5V

T_j=25˚C

–10

–20

–1

–2

0.3

0.6

0.9

1.2

Time t (µs)

Output Current I_O(A)

■Basic Regulator Circuit

Input

Output

AN78M00

AN78M00F

C_I

C_O

C_Iis set when the input line is long.

C_Oimproves the transient response.

Common

■Application Circuit

V_O

V_I

V_O

+V_I

AN78M00

AN78M00F

AN78M00

V_O´

910Ω

R₂

R₁

AN78M00F

V_O´

9.1kΩ

–

I_bias

0.33µF

0.1µF

R₁

R₂

AN6562

10kΩ

V_O´

R₂

V_O= V_O´ + I_bias

R₁

910

9.1k

R₁+ R₂

R₁

V_O= V_O×

–V_I

_Ovaries with the value of the

input voltage V₁.

(In case of R₁+ R₂=10kΩ)

V_I

Q₁

I_I

AN78M00

3Ω

I_O

AN78M00F

R₁

V_O´

V_O

AN78M00

0.33µF

I_bias

AN78M00F

0.1µF

0.33µF

V_O´

I_O=

I_O

+ I_bias

R₁

AN78M07F [PANASONIC]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E