EEHAZSV681UB [PANASONIC]

Conductive Polymer Hybrid Aluminum;


型号：	EEHAZSV681UB
厂家：	PANASONIC
描述：	Conductive Polymer Hybrid Aluminum
文件：	总9页 (文件大小：569K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Conductive Polymer Hybrid Aluminum

Electrolytic Capacitors

Radial Lead Type

ZSU-A series

Hybrid

Features

● Endurance : 4000 h at 125 ℃

● Large capacitance compared with ZS series

● Taping products for automatic insertion

● AEC-Q200 compliant

● RoHS compliant

Specifications

Size code

G12

G16

Category temp. range

Rated voltage range

–55 ℃ to +125 ℃

25 V to 63 V

Nominal cap.range

Capacitance tolerance

DC leakage current

Dissipation factor (tan δ)

Surge voltage (V)

120 μF to 680 μF

180 μF to 1000 μF

±20 % (120 Hz / +20℃)

I ≦ 0.01 CV (μA) After 2 minutes

Please see the attached characteristics list

Rated voltage × 1.25 (15 ℃ to 35 ℃)

+125 ℃ ± 2 ℃, 4000 h, apply the rated ripple current without exceeding the rated voltage.

Capacitance change

Dissipation factor (tan δ)

ESR

Within ±30% of the initial value

≦ 200 % of the initial limit

Within the initial limit

Size code

Endurance

DC leakage current

ESR after endurance

(Ω / 100 kHz)(-40 ℃）

G12

0.3

G16

0.3

After storage for 1000 hours at +125 ℃ ± 2 ℃ with no voltage applied and then being

stabilized at +20 ℃,ꢀcapacitors shall meet the limits specified in endurance.

(With voltage treatment)

Shelf life

+85 ℃ ± 2 ℃, 85 % to 90 %RH, 2000 h, rated voltage applied

Capacitance change

Dissipation factor (tan δ)

ESR

Within ±30% of the initial value

≦ 200 % of the initial limit

Within the initial limit

Damp heat (Load)

DC leakage current

After flow soldering and then being stabilized at +20 ℃, capacitors shall meet the

following limits.

Resistance to

soldering heat

Capacitance change

Dissipation factor (tan δ)

DC leakage current

Within ±10% of the initial value

Within the initial limit

Marking

Shape/taping dimensions

Example : 25 V 680 μF

Marking color : BLACK

øD±0.5

12.7±1.0

6.35±1.0

1.0≧

Negative polarity marking (－)

Capacitance (μF)

Series

ød±0.05

identification

680

E ZS

Rated voltage code

ø4.0±0.2

Lot number

12.7±0.2

R.voltage code

Unit：V

Unit：ｍｍ

Size code

G12

øD

ød

0.8

+0.8

10.0

11.7

15.7

5.0

3.85±0.50

-0.2

+0.8

G16

5.0

-0.2

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

29-Jan-21

Conductive Polymer Hybrid Aluminum Electrolytic Capacitors

ZSU-A series

Characteristics list

Endurance : 125 ℃ 4000 h

Min.packaging

q'ty (pcs)

Case size

(mm)

Specification

Capacitance

Rated

voltage

(V)

Size

code

Ripple

current^*1

(mA rms)

Part number

(±20 %)

(μF)

ESR^*2

(mΩ)

tan δ^*3

øD

ød

Taping

680

1000

470

680

180

270

120

180

10.0 11.7

10.0 15.7

10.0 11.7

10.0 15.7

10.0 11.7

10.0 15.7

10.0 11.7

10.0 15.7

0.8

G12

G16

G12

G16

G12

G16

G12

G16

3500

4000

3500

4000

3200

3700

3000

3500

0.14

0.12

0.10

0.08

EEHAZSE681UB

EEHAZSE102UB

EEHAZSV471UB

EEHAZSV681UB

EEHAZSH181UB

EEHAZSH271UB

EEHAZSJ121UB

EEHAZSJ181UB

500

*1: Ripple current (100 kHzꢀ/ +125 ℃)

*2: ESR (100 kHz / +20 ℃)

*3: tan δ (120 Hz / +20 ℃)

◆ Please refer to the page of “Flow soldering profile” and “The taping dimensions”.

Frequency correction factor for ripple current

Rated capacitance (C) Frequency (f) 100 Hz ≦ f < 120 Hz 120 Hz ≦ f < 200 Hz 200 Hz ≦ f < 300 Hz 300 Hz ≦ f < 500 Hz

Correction

factor

120 μF ≦ C

0.15

0.20

0.25

0.30

Rated capacitance (C) Frequency (f) 500 Hz ≦ f < 1 kHz

Correction

1 kHz ≦ f < 2 kHz

0.50

2 kHz ≦ f < 3 kHz

0.60

3 kHz ≦ f < 5 kHz

0.65

120 μF ≦ C

0.40

factor

Rated capacitance (C) Frequency (f) 5 kHz ≦ f < 10 kHz

Correction

10 kHz ≦ f < 15 kHz

0.75

15 kHz ≦ f < 20 kHz

0.80

20 kHz ≦ f < 30 kHz

0.85

120 μF ≦ C

0.70

factor

500 kHz ≦ f < 1000 kHz

1.00

Rated capacitance (C) Frequency (f) 30 kHz ≦ f < 50 kHz 50 kHz ≦ f < 100 kHz 100 kHz ≦ f < 500 kHz

Correction

120 μF ≦ C

0.85

0.90

1.00

factor

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.

Should a safety concern arise regarding this product, please be sure to contact us immediately.

29-Jan-21

Guidelines and precautions regarding the

technical information and use of our products

described in this online catalog.

■ If you want to use our products described in this online catalog for applications requiring

special qualities or reliability, or for applications where the failure or malfunction of the

products may directly jeopardize human life or potentially cause personal injury

(e.g. aircraft and aerospace equipment, traffic and transportation equipment, combustion

equipment, medical equipment, accident prevention, anti-crime equipment, and/or safety

equipment), it is necessary to verify whether the specifications of our products fit to such

applications. Please ensure that you will ask and check with our inquiry desk as to whether

the specifications of our products fit to such applications use before you use our products.

■ The quality and performance of our products as described in this online catalog only apply

to our products when used in isolation. Therefore, please ensure you evaluate and verify

our products under the specific circumstances in which our products are assembled in your

own products and in which our products will actually be used.

■ If you use our products in equipment that requires a high degree of reliability, regardless

of the application, it is recommended that you set up protection circuits and redundancy

circuits in order to ensure safety of your equipment.

■ The products and product specifications described in this online catalog are subject to

change for improvement without prior notice. Therefore, please be sure to request and

confirm the latest product specifications which explain the specifications of our products in

detail, before you finalize the design of your applications, purchase, or use our products.

■ The technical information in this online catalog provides examples of our products'

typical operations and application circuits. We do not guarantee the non-infringement of

third party's intellectual property rights and we do not grant any license, right, or interest

in our intellectual property.

■ If any of our products, product specifications and/or technical information in this online

catalog is to be exported or provided to non-residents, the laws and regulations of the

exporting country, especially with regard to security and export control, shall be observed.

<Regarding the Certificate of Compliance with

the EU RoHS Directive/REACH Regulations>

■ The switchover date for compliance with the RoHS Directive/REACH Regulations varies

depending on the part number or series of our products.

■ When you use the inventory of our products for which it is unclear whether those products

are compliant with the RoHS Directive/REACH Regulation, please select "Sales Inquiry" in the

website inquiry form and contact us.

We do not take any responsibility for the use of our products outside the scope of the

specifications, descriptions, guidelines and precautions described in this online catalog.

13-Dec-19

Notices / Items to be observed

Notices

■ Applicable laws and regulations

・This product complies with the RoHS Directive (Restriction of the use of certain hazardous substances in

electrical and electronic equipment (DIRECTIVE 2011/65/EU and（EU)2015/863)).

・ No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in

producing this product.

ꢀWe do not use PBBs or PBDEs as brominated flame retardants.

・ Export procedure which followed export related regulations, such as foreign exchange and a foreign trade

method, on the occasion of export of this product.

・ These products are not dangerous goods on the transportation as identified by UN(United Nations) numbers

or UN classification.

■ Limited applications

・ This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home

appliances, computers and other office equipment, optical equipment, measuring equipment.

・ An advanced specification must be signed individually for high-reliability use that might threaten

ꢀhuman life or property due to a malfunction of the capacitor.

■ Intellectual property rights and licenses

・ The technical information in this specification provides examples of our products' typical operations and application

circuits. We do not guarantee the non-infringement of third party's intellectual property rights and we do not grant

any license, right, or interest in our intellectual property.

Items to be observed

■ For specification

・ This specification guarantees the quality and performance of the product as individual components.

The durability differs depending on the environment and the conditions of usage.

Before use, check and evaluate their compatibility with actual conditions when installed in the products.

When safety requirements cannot be satisfied in your technical examination, inform us immediately.

・ Do not use the products beyond the specifications described in this document.

■ Upon application to products where safety is regarded as important

Install the following systems for a failsafe design to ensure safety if these products are to be used in

equipment where a defect in these products may cause the loss of human life or other signification damage,

such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment,

electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime

prevention equipment.

(1) The system is equipped with a protection circuit and protection device.

(2) The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event

of a single fault.

■ Conditions of use

・ Before using the products, carefully check the effects on their quality and performance, and determined

ꢀwhether or not they can be used. These products are designed and manufactured for general-purpose and

ꢀstandard use in general electronic equipment. These products are not intended for use in the following special

ꢀconditions.

(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent.

(2) In direct sunlight, outdoors, or in dust.

(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a

high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx.

(4) In an environment where strong static electricity or electromagnetic waves exist.

(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near

these products.

(6) Sealing or coating of these products or a printed circuit board on which these products are mounted,

with resin and other material.

(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular,

when using water or a water-soluble cleaning agent, be careful not to leave water residues)

(8) Using in the atmosphere where strays acid or alkaline.

(9) Using in the atmosphere where there are excessive vibration and shock.

(10) Using in the atmosphere where there are low pressure or decompression.

・ Please arrange circuit design for preventing impulse or transitional voltage.

ꢀDo not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage,

ꢀinstantaneous high voltage, high pulse voltage etc.

・ Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid

ꢀdeterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and

affects performance, characteristics, and functions of customer system.

13-Dec-19

Conductive Polymer Hybrid Aluminum Electrolytic Capacitors

ꢀꢀApplication guidelines（Hybrid）

1. Circuit design

1.1 Operating temperature and frequency

Electrical characteristics of the capacitor are likely to change due to variation in temperature and/or frequency.

Circuit designers should take these changes into consideration.

(1) Effects of operating temperature on electrical parameters

At higher temperatures : leakage current and capacitance increase while equivalent series resistance

(ESR) decreases.

At lower temperatures : leakage current and capacitance decrease while equivalent series resistance

(ESR) increases.

(2) Effects of frequency on electrical parameters

At higher frequencies

At lower frequencies

: capacitance and impedance decrease while tan δ increases.

: heat generated by ripple current will rise due to an increase in equivalent

series resistance (ESR).

1.2 Operating temperature and life expectancy

(1) Expected life is affected by operating temperature. Generally, each 10 °C reduction in temperature will

double the expected life. Use capacitors at the lowest possible temperature below the upper category

temperature.

(2) If operating temperatures exceed the upper category limit, rapid deterioration of electrical parameter

will occur and irreversible damage will result.

Measure not only the ambient temperature but also the surface temperature of the capacitor’s case top,

which has effects of ripple current and radiated heat from power transistors, IC's, and/or resistors.

Avoid placing components, which could conduct heat to the capacitor from the back side of the circuit board.

(3) The formula for calculating expected life is as follows ;

T1-T2

where T1 ≧ T2

L2 = L1×2

：Guaranteed life (h) at temperature, T¹℃

：Expected life (h) at temperature, T2 ℃

T1 ：Upper category temperature + temperature rise due to rated ripple current (℃)

T2 ：Actual operating temperature, ambient temperature + temperature rise due to ripple current (℃)

(4) Using the capacitor beyond the rated lifetime will result in short circuit, electrolyte leak, vent open, and large

ꢀꢀdeterioration of characteristics. The lifetime cannot exceed 15 years due to aging of sealing rubber.

1.3 Load conditions to avoid

The following load conditions will cause rapid deterioration of capacitor’s electrical characteristics.

In addition, instantaneous heating and gas generation within the capacitor may cause an operation of pressure

relief vent, and that results in electrolyte leaks, explosion and/or fire ignition.

The leaked electrolyte is combustible and electrically conductive.

(1) Reverse voltage

DC capacitors have polarity. Therefore, do not apply the reverse voltage. Find the correct polarity before

insertion.

(2) Charge / Discharge applications

General purpose capacitors are not suitable for use in repeating charge/discharge applications. For such

applications, consult a sales representative with actual application condition. Rush current must not exceed

100 A.

(3) ON-OFF circuit

When using capacitors in circuit where ON-OFF switching is repeated more than 10,000 times a day, consult

a sales representative with actual application condition for an appropriate choice of capacitors.

(4) Over voltage

Do not apply a voltage exceeding the rated voltage. The rated surge voltage can be applied only for a short

time. Make sure that a sum of the DC voltage and the superimposed AC ripple voltage does not exceed the

rated voltage.

(5) Ripple current

Do not apply ripple currents exceeding the rated value.

Make sure that rated ripple currents superimposed on low DC bias voltages do not cause reverse voltage

conditions. Even if the current is below the rated ripple current, using the capacitor for longer than the

rated lifetime will cause ESR increase and internal generation of heat, which may eventually lead to vent open,

bulging of case/rubber, electrolyte leak, short circuit, explosion, or ignition in the worst case.

01-Oct-21

Conductive Polymer Hybrid Aluminum Electrolytic Capacitors

1.4 Connections in parallel

Because the impedance of the capacitor and PCB’s wiring are very close, various impedance values may cause

unbalanced ripple current loads among parallel capacitors. Combine the same part number and wire them carefully

to minimize the potential risk of an excessive ripple current concentrating to one capacitor of the smallest impedance.

The capacitors cannot be used in series.

1.5 Capacitor mounting considerations

(1) For double sided circuit boards, avoid wiring patterns passing between the mounted capacitor and the circuit

board. When a radial lead type capacitor is dipped into a solder bath, an excess solder may deposit under the

capacitor by capillary action, causing short circuit between anode and cathode terminals. Also, lead holes must

be placed with special care for radial lead type capacitors because laminate on capacitor’s surface may become

damaged during flow process.

(2) The pitch between circuit board holes should match the lead wire pitch of the radial lead type capacitors within

the specified tolerances. Unmatched pitch may cause an excessive stress on lead wires during the insertion process

and result in short/open circuit, increased leakage current, or electrolyte leak.

(3) Clearance for case mounted pressure relief (≧ ø10 mm)

Capacitors with case mounted pressure relief require sufficient clearance to allow for proper pressure relief

operation. The minimum clearance are dependent on capacitor diameters as follows.

* ≧ø10 mm : 2 mm minimum

(4) Wiring near the pressure relief (≧ ø10 mm)

Avoid locating high voltage or high current wiring or circuit board paths above the pressure relief.

Flammable, high temperature gas that exceeds 100 ℃ may be released which could dissolve the wire

insulation and ignite.

(5) Circuit board patterns under the capacitor

Avoid circuit board runs under the capacitor, as an electrical short can occur due to an electrolyte leakage.

(6) Resonant vibration after circuit board’s production may make a heavy load on the capacitor and cause rapid

change in characteristics and/or capacitor’s break.

1.6 Electrical isolation

Electrically isolate the capacitor’s case from cathode terminals, as well as circuit patterns.

1.7 Capacitor coating

The laminate coating is intended for marking and identification purposes and is not meant to electrically

insulate the capacitor.

2. Capacitor handling techniques

2.1 Considerations before using

(1) Capacitors have a finite life. Do not reuse or recycle capacitors from used equipment.

(2) Transient recovery voltage may be generated in the capacitor due to dielectric absorption.

If required, this voltage can be discharged with a resistor with a value of about 1 kΩ.

(3) Capacitors stored for a long period of time may exhibit an increase in leakage current.

This can be corrected by gradually applying rated voltage in series with a resistor of approximately 1 kΩ.

(4) If capacitors are dropped, they can be damaged mechanically or electrically. Avoid using dropped

capacitors.

(5) Dented or crushed capacitors should not be used.

The seal integrity can be damaged and loss of electrolyte/ shortened life can result.

2.2 Capacitor insertion

(1) Verify the correct capacitance and rated voltage of the capacitor.

(2) Verify the correct polarity of the capacitor before insertion.

(3) Verify the correct terminal dimension and land pattern size for surface mount type, or holes’ pitch for

radial lead type before mount to avoid short circuit, stress on terminals, and/or lack of terminal strength.

(4) Excessive mounting pressure can cause high leakage current, short circuit, or disconnection.

(5) When using a mounter for radial lead type, avoid cutter wear and acute angle of lead-bending with

respect to circuit board. That may create excessive stress and pull the lead to damage the capacitor.

01-Oct-21

Conductive Polymer Hybrid Aluminum Electrolytic Capacitors

2.3 Reflow soldering (for surface mount type)

(1) Surface-mount type capacitor are exclusively for reflow soldering.

ꢀWhen reflow solder is used an ambient heat condition system such as the simultaneous use of infrared

ꢀand hot-air is recommended.

(2) Observe proper soldering conditions (temperature, time, etc.). Do not exceed the specified limits.

If the peak temperature is high or if the heating time is long, it may cause deterioration of the electrical

characteristics and life characteristics.

Recommended soldering condition is a guideline for ensuring the basic characteristics of the components,

but not for the stable soldering conditions. Conditions for proper soldering should be set up according to

individual conditions.

ꢀ✽ The Temperature on capacitor top shall be measured by using thermal couple that is fixed firmly by

epoxy glue.

(3) In case of use in 2 times reflow, 2nd reflow must be done when the capacitor’s temperature return back

ꢀto normal level.

(4) In our recommended reflow condition , the case discoloration and the case swelling might be slightly

ꢀgenerated. But please acknowledge that these two phenomena do not influence the reliability of the product.

(5) The crack on top marking might be occurred by reflow heat stress.

ꢀBut please acknowledge that it does not influence the reliability of the product.

(6) VPS (Vapor Phase Soldering) reflow can cause significant characteristics change and/ or mounting failure

ꢀdue to deformation by acute temperature rise.

ꢀVPS is acceptable provided that the process does not exceed recommended reflow profile and

ꢀtemperature rise is less than 3 ℃ / sec. ꢀPlease contact Panasonic for detailed conditions.

(7) The vibration-proof capacitors of size ø6.3 has support terminals extending from the bottom side to the lead edge.

Then, make sure to find appropriate soldering conditions to form fillet on the support terminals if required for

appearance inspection. However, even if sufficient solder fillets are not observed, the reliability of vibration-proof

will not be lowered because the support terminals on the bottom side enhance the solder joint to PCB.

2.4 Flow soldering (for radial type)

(1) Radial lead type capacitors cannot apply to reflow soldering.

(2) Do not immerse the capacitor body into the solder bath as excessive internal pressure could result.

(3) Apply proper soldering conditions (temperature, time, etc.). Do not exceed the specified limits.

(4) Do not allow other parts or components to touch the capacitor during soldering.

(5) When mounting the radial type being touched to PCB, be sure to check the appearance of solder under the

sealing rubber, which does not have an airflow structure.

2.5 Manual soldering

(1) Apply soldering conditions (temperature and time) based on the specification, or do not exceed temperature of

350 ℃ for 3 seconds.

(2) If a soldered capacitor must be removed and reinserted, avoid excessive stress on the capacitor leads.

(3) Avoid physical contacts between the tip of the soldering iron and capacitors to prevent or capacitor failure.

(4) When bending lead wires of radial type capacitors to match the hole pitch on PCB, avoid applying excessive

stress to the capacitor body.

2.6 Capacitor handling after soldering

(1) Avoid moving the capacitor after soldering to prevent excessive stress on the lead wires where they enter

the seal. The capacitor may break from element portion due to a torque at outer rim, causing a large stress

to terminals.

(2) Do not use the capacitor as a handle when moving the circuit board assembly. The total weight of the

board would apply to element portion through terminals, and the capacitor may break.

(3) Avoid striking the capacitor after assembly to prevent failure due to excessive shock. The capacitor may

break due to excessive shock or load above specified range.

01-Oct-21

Conductive Polymer Hybrid Aluminum Electrolytic Capacitors

2.7 Circuit board cleaning

(1) Circuit boards can be immersed or ultrasonically cleaned using suitable cleaning solvents for up to

5 minutes and up to 60 °C maximum temperatures. The boards should be thoroughly rinsed and dried.

The use of ozone depleting cleaning agents is not recommended for the purpose of protecting our

environment.

【Target solvent】

Pine Alpha ST-100S, Aqua Cleaner 210SEP, Clean-thru 750H / 750L / 710M, Sunelec B-12,

Sunelec B-12, Cold Cleaner P3-375, Techno Cleaner 219, DK Be-clear CW-5790,

Telpene Cleaner EC-7R, Technocare FRW-17 / FRW-1 / FRV-1

(2) Avoid using the following solvent groups unless specifically allowed in the specification ;

(a) Halogenated based solvents ： may permeate the seal and cause internal corrosion.

Especially, 1-1-1 trichloroethane must not be used on any aluminum electrolytic capacitors.

(b) Alkaline based solvents

(d) Xylene

： may dissolve and react to the aluminum case.

： may deteriorate the sealing rubber

(e) Acetone

： may erase the markings on the capacitor top

(3) A thorough drying after cleaning is required to remove residual cleaning solvents that may be trapped

between the capacitor and the circuit board. Avoid drying temperatures, which exceed the upper category

temperature of the capacitor.

(4) Monitor the contamination levels of cleaning solvents during use in terms of electrical conductivity, pH, specific

gravity, and water content. Inside the capacitor may corrode with high density of chlorine. Control the flux

density in the cleaning agent to be less than 2 mass%.

(5) Depending on the cleaning method, the marking on a capacitor may be erased or blurred.

※ Please consult us if you are not certain about acceptable cleaning solvents or cleaning methods.

2.8 Mounting adhesives and coating agents

When using mounting adhesives or coating agents to control humidity, avoid using materials containing

halogenated solvents.

Also, avoid the use of chloroprene based polymers.

Cure or dry out the coating agents thoroughly, and do not leave any solvents. Make sure to dry out cleaning agents

completely immediately after washing the circuit board if the capacitors are mounted afterward, so that the solvents

are not left under the capacitor body. Also, leave more than 1/3 of the sealing portion open, and do not cover that

portion with any adhesives or coating.

2.9 Potting and molding

Potting and molding processes cannot be recommended. They have potential risks to change the capacitor’s

performance and reliability due to injection pressure, diffused material into the capacitor, as well as heat

accumulation by covered resin. Also, evaporated electrolyte may remain inside the resin, then turn to liquid, and

possibly short circuit PCB patterns.

2.10 Fumigation

In exporting electronic appliances with aluminum electrolytic capacitors, in some cases fumigation treatment

using such halogen compound as methyl bromide is conducted for wooden boxes.

If such boxes are not dried well, the halogen left in the box is dispersed while transported and enters in the

capacitors inside.

This possibly causes electrical corrosion of the capacitors. Therefore, after performing fumigation and drying

make sure that no halogen is left.

Don’t perform fumigation treatment to the whole electronic appliances packed in a box.

2.11 Flux

If you use a halogen type (Chlorine type, Bromine type, etc.) high-activity flux, please use it after confirmation

in advance, as it may have an impact on performance and reliability of this product due to the residue of the flux.

3. Precautions for using capacitors

3.1 Environmental conditions

Capacitors should not be stored or used in the following environments.

(1) Exposure to temperatures above the upper category or below the lower category temperature of the capacitor.

(2) Direct contact with water, salt water, or oil.

(3) High humidity conditions where water could condense on the capacitor.

(4) Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, chlorine compound,

bromine, bromine compound or ammonia.

(5) Exposure to ozone, radiation, or ultraviolet rays.

(6) Vibration and shock conditions exceeding specified requirements.

Even within the specified requirements, a large vibration acceleration may be applied due to resonance,

so be sure to evaluate and confirm with the actual product.

01-Oct-21

Conductive Polymer Hybrid Aluminum Electrolytic Capacitors

3.2 Electrical precautions

(1) Avoid touching the terminals of a capacitor as a possible electric shock could result. The exposed

aluminum case is not insulated and could also cause electric shock if touched.

(2) Avoid short circuiting the area between the capacitor terminals with conductive materials including liquids

such as acids or alkaline solutions.

(3) A low-molecular-weight-shiroxane which is included in a silicon material shall causes abnormal electrical

characteristics.

4. Emergency procedures

(1) If the pressure relief of the capacitor operates, immediately turn off the equipment and disconnect from

the power source.

This will minimize an additional damage caused by the vaporizing electrolyte.

(2) Avoid contact with the escaping electrolyte gas, which can exceed 100 °C temperatures.

If electrolyte or gas enters the eye, immediately flush the eye with large amounts of water.

If electrolyte or gas is ingested by mouth, gargle with water.

If electrolyte contacts the skin, wash with soap and water.

5. Long term storage

(1) Leakage current of a capacitor tends to increase after a long-term storage due to dielectric dissolution,

and very high current may flow at the first voltage load. However, applying voltage will form the dielectric,

and the leakage current will decrease. Expiration date is 42 months from the outgoing inspection date.

Storage condition is to keep in room temperature (5 ℃ to 35 ℃) and humidity (45 % to 85 %) with no

direct sunshine.

(2) Environmental conditions

Do not store under condition outside the area described in the specification, and also under conditions

listed below.

(a) Exposure to temperatures above the upper category or below the lower category temperature of the

capacitor.

(b) Direct contact with water, salt water, or oil.

(d) Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, Chlorine compound,

Bromine, Bromine compound or ammonia.

(e) Exposure to ozone, radiation, or ultraviolet rays.

(f) Vibration and shock conditions exceeding specified requirements.

6. Capacitor disposal

When disposing capacitors, use one of the following methods.

(1) Incinerate after crushing the capacitor or puncturing the can wall (to prevent explosion due to internal

pressure rise).

(2) Dispose as solid waste.

NOTE : Local laws may have specific disposal requirements which must be followed.

The precautions in using aluminum electrolytic capacitors follow the "Safety application

guide for the use in fixed aluminum electrolytic capacitors for electronic equipment",

RCR-2367D issued by JEITA in October 2017.

Please refer to the above application guide for details.

■ AEC-Q200ꢀcompliant

The products are tested based on all or part of the test conditions and methods defined in AEC-Q200.

Please consult with Panasonic for the details of the product specification and specific evaluation test results,

etc., and please review and approve Panasonic's product specification before ordering.

✽ Intellectual property right

We, Panasonic Group are providing the product and service that customers can use without anxiety, and are

working positively on the protection of our products under intellectual property rights.

Representative patents relating to Conductive Polymer Hybrid Aluminum Electrolytic Capacitors are as follows:

US Patent No.7497879, No.7621970, No.9208954, No.9595396, No.9966200, No.10453618,

No.10559432, No.10679800, No.10685788, No.10790095

JP Patent

No.5360250

EP Patent No.1808875, No.2698802

01-Oct-21

EEHAZSV681UB [PANASONIC]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E