EX-Z11FA-P [PANASONIC]
Through Beam Photoelectric Sensor,;
| 型号： | EX-Z11FA-P |
| 厂家： | 
PANASONIC |
| 描述： | Through Beam Photoelectric Sensor, 传感器 换能器 |
| 文件： | 总8页 (文件大小：4544K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Amplifier Built-in
Ultra-minute Photoelectric Sensor
EX-ZSERIES
Conforming to
Recognition
EMC Directive
The World’s No. 1
in Compactness
* Among photoelectric sensors with built-in amplifier, as of June 2015 (survey by our company)
(Actual size)
panasonic.net/id/pidsx/global
2015.07
ilt-in
The World’s Smallest* Size
* Among photoelectric sensors with built-in amplifier, as of June 2015 (survey by our company)
Unit volume ratio reduced by about 50%*
* As compared to EX-10 series
EX-Z13□
Sensing range: 500 mm 19.685 in
Repeatability: 0.05 mm 0.002 in or less
Minimum sensing object:
ø1.0 mm ø0.039 in opaque object
Front sensing type
Side sensing type
EX-Z12□
Sensing range: 200 mm 7.874 in
Repeatability: 0.03 mm 0.001 in or less
Minimum sensing object:
Approx.
Approx.
ø0.5 mm ø0.020 in opaque object
50% smaller
in volume ratio
than EX-10
35% smaller
in volume ratio
than EX-10
EX-Z11□
EX-Z1□F□
EX-Z1□
Sensing range: 50 mm 1.969 in
Repeatability: 0.02 mm 0.001 in or less
Minimum sensing object:
W8 × H14 × D3 mm
W5.5 × H15.9 × D6.5 mm
W0.315 × H0.551 × D0.118 in
W0.217 × H0.626 × D0.256 in
ø0.3 mm ø0.012 in opaque object
Small-object sensing capability
Capability to sense a small ø1.0 mm ø0.039 in object
EX-Z13□
over long distance
Clearly
visible
spotlight
Built-in slit
EX-Z11□
Slit diameter: 0.3 mm 0.012 in
Sensing of end of thin pipe
2
A wide range of applications
Inflection resistant cable type available for all models
Examples of applications
Inflection resistant cable type with
improved flex resistance is available
for all models. Select the model
suitable for your specific application.
The standard type comes with lead
wires with the same diameter as
previous models, but the outside
diameter of the cable is 2.0 mm
0.079 in and thinner than the cables
of the EX-10 series. This facilitates
cable routing.
Detection of parts in parts feeder
IP67 protective structure
The sensors features an IP67
protective structure to allow their use
in process lines where water is used
or splashed.
Rust-resistant stainless steel sensor
mounting brackets and screws are
available.
Note: If water splashes on the sensor during
sensing operation, it may sense water as
an object.
IP67
(IEC)
Detection of presence / absence of test
tube tray
Options
A variety of mounting brackets are available!
A spacer for mounting at the back (1 type) for through-wall sensing and sensor
mounting brackets (3 types) are available to meet a diversity of sensor installation
needs.
Spacer for mounting at the back
(for front sensing type only)
Operation indicator (orange) can
be checked from the rear side.
Detection of LED lead
Through-wall detection
3
Ultra-minute Photoelectric Sensor EX-ZSERIES
ORDER GUIDE
Model No. (Note)
NPN output
Output
operation
Type
Appearance
Sensing range
PNP output
EX-Z11FA-P
EX-Z11FB-P
EX-Z12FA-P
EX-Z12FB-P
EX-Z13FA-P
EX-Z13FB-P
EX-Z11FA-P-R
EX-Z11FB-P-R
EX-Z12FA-P-R
EX-Z12FB-P-R
EX-Z13FA-P-R
EX-Z13FB-P-R
EX-Z11A-P
EX-Z11FA
EX-Z11FB
EX-Z12FA
EX-Z12FB
EX-Z13FA
EX-Z13FB
EX-Z11FA-R
EX-Z11FB-R
EX-Z12FA-R
EX-Z12FB-R
EX-Z13FA-R
EX-Z13FB-R
EX-Z11A
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
Light-ON
Dark-ON
50 mm 1.969 in
200 mm 7.874 in
500 mm 19.685 in
50 mm 1.969 in
50 mm 1.969 in
50 mm 1.969 in
200 mm 7.874 in
500 mm 19.685 in
EX-Z11B
EX-Z11B-P
EX-Z12A
EX-Z12A-P
200 mm 7.874 in
EX-Z12B
EX-Z12B-P
EX-Z13A
EX-Z13A-P
500 mm 19.685 in
EX-Z13B
EX-Z13B-P
EX-Z11A-R
EX-Z11B-R
EX-Z12A-R
EX-Z12B-R
EX-Z13A-R
EX-Z13B-R
EX-Z11A-P-R
EX-Z11B-P-R
EX-Z12A-P-R
EX-Z12B-P-R
EX-Z13A-P-R
EX-Z13B-P-R
200 mm 7.874 in
500 mm 19.685 in
Note: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting brackets
(MS-EXZ-□).
Note: The model No. with “E” shown on the label affixed to the thru-beam type sensor is the emitter, “D” shown on the label is the receiver.
OPTIONS
Designation
Model No.
Description
L-shaped mounting bracket (SUS304) for front sensing and side sensing types
(2 sets are required)
MS-EXZ-1
MS-EXZ-2
MS-EXZ-3
Sensor mounting
bracket
Mounting bracket (SUS304) for front sensing type
(2 sets are required)
Mounting bracket (SUS304) for side sensing type
(2 sets are required)
Spacer for
mounting at the
back
MS-EXZ-4
Spacer for mounting at the back (polyacetal) for front sensing type
Sensor mounting bracket
Spacer for mounting at the back
• MS-EXZ-4
• MS-EXZ-1
• MS-EXZ-2
• MS-EXZ-3
Material: Stainless steel
(SUS304)
Material: Polyacetal
Material: Stainless steel
(SUS304)
Material: Stainless steel
(SUS304)
Two M2 (length 4 mm
0.157 in) pan head screws
and two M2 (length 8 mm
0.315 in) pan head screws
are attached.
M2 (length: 10 mm 0.394 in)
screws, nuts, spring
washers and flat washers
are attached. (20 pieces
each)
Two M2 (length 4 mm
0.157 in) pan head screws
are attached.
Two M2 (length 8 mm
0.315 in) pan head screws
are attached.
4
Ultra-minute Photoelectric Sensor EX-ZSERIES
SPECIFICATIONS
Thru-beam
Front sensing Side sensing
EX-Z11A(-P)(-R) EX-Z12FA(-P)(-R) EX-Z12A(-P)(-R) EX-Z13FA(-P)(-R) EX-Z13A(-P)(-R)
EX-Z11FB(-P)(-R) EX-Z11B(-P)(-R) EX-Z12FB(-P)(-R) EX-Z12B(-P)(-R) EX-Z13FB(-P)(-R) EX-Z13B(-P)(-R)
Type
Front sensing
EX-Z11FA(-P)(-R)
Side sensing
Front sensing
Side sensing
Light-ON
Dark-ON
Model No.
(Note 2)
Item
Sensing distance
50 mm 1.969 in
200 mm 7.874 in
500 mm 19.685 in
ø0.3 mm ø0.012 in opaque object
ø0.5 mm ø0.02 in opaque object
ø1.0 mm ø0.039 in opaque object
(Completely beam interrupted object)
(Completely beam interrupted object)
(Completely beam interrupted object)
Minimum sensing object
Setting distance between emitter
Setting distance between emitter
Setting distance between emitter
and receiver: 50 mm 1.969 in
and receiver: 200 mm 7.874 in
and receiver: 500 mm 19.685 in
Hysteresis
Repeatability
(Perpendicular to sensing axis)
0.02 mm 0.001 in or less
0.03 mm 0.001 in or less
0.05 mm 0.002 in or less
Supply voltage
12 to 24 V DC ±10 % Ripple P-P 10 % or less
Emitter: 10 mA or less, Receiver: 10 mA or less
<PNP output type>
Current consumption
<NPN output type>
NPN open-collector transistor
PNP open-collector transistor
Output
• Maximum sink current: 20 mA
• Maximum source current: 20 mA
• Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 1.5 V or less (at 20 mA sink current)
• Applied voltage: 30 V DC or less (between output and +V)
• Residual voltage: 1.5 V or less (at 20 mA source current)
Short-circuit protection
Response time
Incorporated
0.5 ms or less
Operation indicator
Stability indicator
Protection
Orange LED (Lights up when the sensing output is ON)
Green LED (Lights up under the stable light received condition or the stable dark condition)
IP67 (IEC)
Ambient temperature
Ambient humidity
Ambient illuminance
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Light emitting element
Grounding
-10 to +55 °C 14 to +131 °F (No dew condensation or icing allowed), Storage: -30 to +70 °C -22 to +158 °F
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 5,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)
Floating
Material
Enclosure: PBT, Lens: Polycarbonate, Metallic part: Stainless steel (SUS304) (SUS301 for rear side of front sensing type)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Cable (Note 3)
Cable extension
Weight
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (both emitter and receiver).
Net weight (each emitter and receiver): 15 g approx., Gross weight: 35 g approx.
M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)
Accessories
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23°C 73°F.
2) Model Nos. having the “-P” are PNP output type and model Nos. having the “-R” are inflection resistant cable type.
3) The inflection resistant cable type has a 0.1 mm2 3-core (thru-beam type emitter: 2-core) flexible cabtyre cable, 2 m 6.562 ft long.
PRECAUTIONS FOR PROPER USE
• Never use this product as a sensing device for personnel protection.
• In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI
or IEC etc., for personnel protection applicable in each region or country.
Mounting
• In case of mounting on tapped holes (Unit: mm in)
• In case of using attached screws and nuts (Unit: mm in)
Side sensing Front sensing
Side sensing
Front sensing
Nut
Spring
washer
Flat
washer
Nut
Spring
washer
Flat
washer
Sensing
direction
8.5
0.335
Sensing
direction
8.5
0.335
Sensing
direction 0.335
Sensing
direction
8.5
0.335
8.5
M2 × 0.4 0.016 hole
tapped, 7 0.276 deep
M2 screw (length 6 0.236)
(accessory)
M2 screw (length 10 0.394)
(accessory)
M2 × 0.4 0.016 hole
tapped, 5 0.197 deep
M2 screw (length 10 0.394)
(accessory)
Thickness of mounting
plate: 2 0.079 or less
Thickness of mounting
plate: 2 0.079 or less
M2 screw (length 6 0.236)
(accessory)
The tightening torque should be 0.2 N·m or less.
The tightening torque should be 0.2 N·m or less.
Other
• Do not use during the initial transient time (0.5 sec. approx.) after the power supply is switched on.
5
Ultra-minute Photoelectric Sensor EX-ZSERIES
I/O CIRCUIT DIAGRAMS
NPN output type
I/O circuit diagram
Color code
PNP output type
I/O circuit diagram
Color code
1
D
(Brown) +V
(Brown) +V
ZD
D
Load
(Black) Output (Note)
20mA max.
+
−
2
D
+
−
12 to 24 V DC
10 %
12 to 24 V DC
10 %
Tr
(Black) Output (Note)
2
Tr
20 mA max.
(Blue) 0 V
Load
ZD
1
D
(Blue) 0 V
Internal circuit
Users’ circuit
Internal circuit
Users’ circuit
Note: The emitter does not incorporate the output.
Note: The emitter does not incorporate the output.
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode
ZD: Surge absorption zener diode
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode
ZD: Surge absorption zener diode
Tr: NPN output transistor
Tr: PNP output transistor
SENSING CHARACTERISTICS (TYPICAL)
Thru-beam type
Angular deviation
Thru-beam type
EX-Z11F□ EX-Z11□
EX-Z12F□ EX-Z12□
Parallel deviation
Parallel deviation
Angular deviation
80
3.150
80
3.150
Emitter Receiver
θ
200
7.874
200
7.874
L
60
2.362
60
2.362
40
1.575
40
1.575
100
3.937
100
3.937
Emitter
20
Emitter
Receiver
20
Emitter
0.787
0.787
Receiver
0
ℓ
ℓ
θ
L
L
L
Receiver
0
0
0
0
20
10
0
10
0.394
20
0.787
100
50
50
100
100
3.937
50
1.969
0
50
100
3.937
100
50
Left
0
50
Right
100
0.787
0.394
1.969
Left
Center
Right
Left
Center
Right
Left
Center
Right
Center
Operating position ℓ (mm in)
Operating angle θ (°)
Operating position ℓ (mm in)
Operating angle θ (°)
Thru-beam type
EX-Z13F□ EX-Z13□
Parallel deviation
Angular deviation
800
800
Emitter
Emitter
31.496
31.496
Receiver
Receiver
θ
ℓ
L
600
23.622
600
23.622
L
400
15.748
400
15.748
200
7.874
200
7.874
0
0
100
50
0
50
1.969
Right
100
3.937
100
50
Left
0
50
Right
100
3.937
1.969
Left
Center
Center
Operating position ℓ (mm in)
Operating angle θ (°)
6
Ultra-minute Photoelectric Sensor EX-ZSERIES
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from the website.
Sensor
EX-Z11F□ EX-Z12F□ EX-Z13F□
Operation indicator (Orange)
Stability indicator (Green)
Operation indicator (Orange)
Stability indicator (Green)
4.4
1.75
0.069
4.4
0.173
0.173
1.75 0.069
Beam-emitting
part
Beam-receiving
part
2-ø2.2 ø0.087
mounting holes
ø2.2 ø0.087
mounting holes
1.5
0.059
2.225 0.088
4.45 0.175
2.225 0.088
4.45 0.175
1.5
0.059
ø2.0 ø0.079 cable,
2 m 6.562 ft long
ø2.0 ø0.079 cable,
2 m 6.562 ft long
3
0.118
3
0.118
8 0.315
8 0.315
Emitter
Receiver
Sensor
EX-Z11□ EX-Z12□ EX-Z13□
6.5
0.256
6.5
0.256
2.2
0.087
2.2 0.087
Operation indicator (Orange)
Operation indicator (Orange)
Stability indicator (Green)
Stability indicator (Green)
Beam-emitting part
Beam-receiving part
ø2.0 ø0.079 cable,
2 m 6.562 ft long
ø2.0 ø0.079 cable,
2 m 6.562 ft long
2-ø2.2 ø0.087
mounting holes
2-ø2.2 ø0.087
mounting holes
2.5 0.098
2.9 0.114
5.5 0.217
2.9 0.114
2.5 0.098
4.25 0.167
4.25 0.167
5.5 0.217
Emitter
Receiver
Sensor mounting bracket (Optional)
Sensor mounting bracket (Optional)
MS-EXZ-1
MS-EXZ-2
18.7 0.736
10.5
0.413
7
9 0.354
0.276
4-M2 × 0.4 0.016
thru-hole threads
1.4 0.055
6.25
0.246
1.75
0.069
3.2
0.126
1.75 0.069
4.75 0.187
6.8
0.268
8.5
0.335
3.2
0.126
4-M2 × 0.4 0.016
thru-hole threads
Material: Stainless steel (SUS304)
3.5
0.138
Two M2 (length 4 mm 0.157 in) pan head screws and two M2
(length 8 mm 0.315 in) pan head screws are attached.
6.8
0.268
Material: Stainless steel (SUS304)
Two M2 (length 4 mm 0.157 in) pan head screws are attached.
7
Ultra-minute Photoelectric Sensor EX-ZSERIES
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from the website.
Sensor mounting bracket (Optional)
Spacer for mounting at the back (Optional)
MS-EXZ-3
MS-EXZ-4
17.7 0.697
7.5
0.295
2-ø2.2 ø0.087
3.5
0.138
9.9
0.390
1.4
1.7 0.067
3.5 0.138
2.8 0.110
0.055
4.5
0.177
Material: Polyacetal
Set of 10 pieces
M2 (length: 10 mm 0.394 in) screws, nuts, spring washers
3.2
0.126
2-M2 × 0.4 0.016
thru-hole threads
and flat washers are attached. (20 pieces each)
6.8
0.268
Material: Stainless steel (SUS304)
Two M2 (length 8 mm 0.315 in) pan head screws are attached.
EX Family Products
Amplifier Built-in
Amplifier Built-in
Amplifier Built-in
Threaded Miniature Photoelectric Sensor
Ultra-slim Photoelectric Sensor
Ultra-compact Photoelectric Sensor
EX-10SERIES Ver.2
EX-20SERIES Ver.2
EX-30SERIES Ver.2
Ultra-thin dimension
Easy installation with M3 screws
One-point mounting
• Only 3.5 mm 0.138 in thick
• Long sensing range of 1 m 3.281 ft
• High speed response of 0.5 ms
• Equipped with sensitivity adjuster
• Long sensing range of 2 m 6.562 ft
• Red spotlight for easy confirmation of
sensing point
• Simple design with sensing axis
corresponding with mounting hole
• Can be installed using the same thread
size (M4 for thru-beam type, M6 for
reflective type) as that of standard fiber
Disclaimer
The applications described in the catalog are all intended for examples only. The purchase of our products described in the catalog shall not be regarded as
granting of a license to use our products in the described applications. We do NOT warrant that we have obtained some intellectual properties, such as patent
rights, with respect to such applications, or that the described applications may not infringe any intellectual property rights, such as patent rights, of a third party.
Please contact:
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Global Sales Department
■Telephone: +81-568-33-7861 ■Facsimile: +81-568-33-8591
panasonic.net/id/pidsx/global
All Rights Reserved ©
2015
Printed in Japan
No. CE-EXZ-10 July, 2015
Specifications are subject to change without notice.
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明