HL-T1001F [PANASONIC]
Ultra-compact Laser Collimated Beam Sensor;型号: | HL-T1001F |
厂家: | PANASONIC |
描述: | Ultra-compact Laser Collimated Beam Sensor |
文件: | 总12页 (文件大小:903K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Ultra-compact Laser Collimated Beam Sensor
1111
HL-T1 SERIES
■General terms and conditions............. F-3
■Selection guide............................ P.1021~
■About laser beam......................... P.1593~
FIBER
SENSORS
Related Information
■
Glossary of terms / General precautions ..... P.1587 / P.1595
LASER
SENSORS
PHOTOELECTRIC
SENSORS
Conforming to
FDA regulations
(
)
HL-T□F only
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
This product is classified as a
Class 1 Laser Product in IEC /
JIS standards and a Class II
Laser Product in FDA regulations.
Do not look at the laser beam
through optical system such as
a lens.
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
panasonic.net/id/pidsx/global
STATIC
CONTROL
DEVICES
LASER
Ultra-compact sensor head A high-functionality
intelligent controller
MARKERS
PLC
HUMAN MACHINE
INTERFACES
Ultra-compact sensor head
Resolution of 4 µm 0.157 mil
ENERGY
MANAGEMENT
SOLUTIONS
The ultra-compact size and yet the high level of performance.
These sensors save space.
A high resolution of 4 μm 0.157 mil (at an average
64 cycles) allows high-precision positioning and size
judgment.
FA COMPONENTS
HL-T1001A(F)
HL-T1005A(F)
HL-T1010A(F)
MACHINE VISION
SYSTEMS
Emitter
34 mm
1.339 in
Emitter
Distinguishing size of
electronic components
15mm 0.591 in
UV CURING
SYSTEMS
20 mm 0.787 in
42 mm
1.654 in
15 mm 0.591 in
20 mm
0.7487 in
19 mm 0.748 in
15 mm 0.591 in
15 mm
0.591 in
20 mm
0.787 in
25 mm
0.984 in
20 mm
0.787 in
Selection
Guide
Laser
Displacement
Receiver
Receiver
Magnetic
Displacement
Contact
BASIC PERFORMANCE
Long sensing range
Displacement
Collimated
Beam Sensors
Metal-sheet
Double-feed Detection
Minimum sensing object
diameter ø8 µm ø0.315 mil
HL-T1001A(F)
Digital Panel
Controller
Long sensing range of 500 mm 19.685 in
[HL-T1005A(F), HL-T1010A(F)] and 2 m 6.562 ft
[HL-T1001A(F)] are available.
The laser with a beam
diameter of ø1 mm
ø0.039 in can sense
extremely small objects
with dimensions in
micrometers such as
bonding wires.
Other Products
HL-T1
LD
High-precision judgment even from
minute differences in light intensity
LA
The sensors are sensitive
Distinguishing opacity of glass
to minute differences in
light intensity, so that
they can judge even
the opacity of glass.
In addition, the amount
of light received can be
displayed as a percentage
to allow you to determine
permeation rates.
Adoption of a Class 1 laser
The adoption of a Class 1 laser (IEC / JIS) eliminates the
need for safety countermeasures, so that these sensors
can be used in photoelectric sensor applications with
confidence.
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1112
APPLICATIONS
FIBER
SENSORS
LASER
SENSORS
Checking the positioning of chip components
Detecting defective lead frame seating
Sensing wafer position in wafer cassette
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
FUNCTIONS
Fully equipped with convenient functionality
Analog output is switchable between current / voltage
SENSOR
OPTIONS
A wide range of convenient features has been incorporated
into the unit’s compact body: standard received light setting
/ auto scaling setting / measurement processing (various
timer and hold functions) / differentiation / monitor focus
function. These features make the unit useful for a wide
variety of applications.
The analog output can be switched between either of
two different outputs; current (4 to 20 mA) / voltage
(±4 V). With the monitor focus function, the output can
be adjusted over the range from –5 V to +5 V, or from
0 V to +5 V, facilitating connectivity with a variety of
output devices.
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
3 types of teaching functions are now available
Monitor focus function
The linear output is fully adjustable over the following
range (current: 4 to 20 mA / voltage: ±4 V). The usage
of the monitor focus function together with selectable
current / voltage switching for the linear output allows for
compatibility with a variety of output devices.
(Examples)
3 types of teaching functions are available: positioning
teaching / 2-point teaching / automatic teaching, thus
enabling a variety of applications to be accommodated
for many different types of production sites.
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
The actual value measured at the time when teaching
Positioning
is performed is utilized as the threshold value.
teaching
ENERGY
MANAGEMENT
SOLUTIONS
Best suited for high-precision positioning.
+4
In this teaching method, an intermediate level between
the first and the second teaching levels is utilized as
FA COMPONENTS
the threshold value. Minute differences, such as
changes as small as the thickness of a sheet of paper
between the sensing objects, can be detected when
this teaching method is utilized.
2-point
teaching
MACHINE VISION
SYSTEMS
–4
With this teaching method, a series of periodic arbitrarily
measurements are taken automatically and an
intermediate value, between the maximum and minimum
values obtained by this measurement, is utilized as the
threshold value. The threshold value is therefore set in
relation to the sensing object. Best suited for
UV CURING
SYSTEMS
Automatic
teaching
0
5.0
0.197
Sensor display value (mm in)
applications in which teaching must be performed
without stopping the current flow of operations.
In the event that
In the event that
5 mm 0.197 in: +1 V
0 mm 0 in: +5 V
5 mm 0.197 in: +5 V
0 mm 0 in: +1 V
Selection
Guide
Laser
Displacement
Magnetic
Displacement
Contact
Displacement
Collimated
Beam Sensors
Metal-sheet
Double-feed Detection
Digital Panel
Controller
Detection resolution can be easily confirmed
The current resolution can be easily confirmed by setting
the controller to indicate resolution display mode.
By displaying the resolution, the marginal increment can
be easily determined for the threshold value setting,
helping to accurately determine whether sensing can be
+5
+1
+5
+1
performed.
Resolution
indicator
Other Products
0
5.0
0
5.0
0.197
0.197
Sensor display value (mm in)
Sensor display value (mm in)
HL-T1
LD
The linear output must be set by determining output
values (maximum; current: 0 to 23.5 mA / voltage: 5.5 V)
at two different points, for the arbitrary display value.
LA
MAINTENANCE
Self-check for laser diode deterioration
The intelligent controller performs self-checking for laser
diode deterioration. If the controller detects significant
deterioration (end of diode life), an error will be displayed
on the main digital display panel. This function enables
users to prepare in advance for potential laser diode
malfunctions.
Error display
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1113
OPERABILITY
OPTIONS
FIBER
SENSORS
Superior operability has been achieved
Calculations for 2 sensors are possible
LASER
SENSORS
All settings can be easily performed by using the four-way
keys and viewing the digital displays.
The calculation unit (optional) just needs to be connected
between the two controllers to enable calculations (addition
and subtraction) to be carried out for two sensors. No digital
panel controller is needed either.
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
Large dual digital display
ELECTRIC
SENSORS
After power up, the measured value (red) and the
threshold value (yellow) are displayed
(letter height 7 mm 0.276 in)
AREA
SENSORS
Judgment output indicators
SAFETY LIGHT
Sheet width measurement
CURTAINS
/
HIGH (Orange) / PASS (Green) / LOW
(Yellow) 3-color display
SAFETY
COMPONENTS
Calculation unit
HL-AC1-CL
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
Easy operation with four-way keys
SIMPLE
WIRE-SAVING
UNITS
ORDER GUIDE
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
Sensor heads
SENSORS
STATIC
CONTROL
DEVICES
Min. sensing
object
Conforming
standards / regulations
Type
Appearance
Sensing range
Sensing width
Model No.
LASER
MARKERS
ø8 µm ø0.315 mil
opaque object
ø50 µm ø1.969 mil
opaque object at
500 to 2,000 mm
ø1 mm ø0.039 in
ø1 to ø2.5 mm
ø0.039 to ø0.098 in
at 500 to 2,000 mm
19.685 to 78.740 in
sensing range
IEC / JIS
HL-T1001A
PLC
2 m 6.562 ft
HUMAN
MACHINE
INTERFACES
19.685 to 78.740 in
sensing range
FDA /
IEC / JIS
ENERGY
MANAGEMENT
SOLUTIONS
HL-T1001F
HL-T1005A
HL-T1005F
HL-T1010A
HL-T1010F
FA
COMPONENTS
MACHINE
VISION
IEC / JIS
SYSTEMS
ø0.05 mm ø0.002 in
opaque object
500 mm 19.685 in
UV
CURING
5 mm 0.197 in
SYSTEMS
FDA /
IEC / JIS
Selection
Guide
IEC / JIS
Laser
Displacement
ø0.1 mm ø0.004 in
opaque object
Magnetic
500 mm 19.685 in
10 mm 0.394 in
Displacement
Contact
Displacement
FDA /
IEC / JIS
Collimated
Beam
Sensors
Metal-sheet
Double-feed
Detection
Note: The model No. with “P” shown on the label affixed to the product is the emitter, “D” shown on the label is the receiver.
Digital Panel
Controller
Other
Products
Accessories
• MS-HLT1-1
Sensor mounting bracket
• MS-LA3-1
• CN-HLT1-1
(Sensor head to controller connection cable)
HL-T1
LD
Sensor mounting bracket
for HL-T1010A(F)
(Note)
HL-T1001A(F) /
for
HL-T1005A(F)
(Note)
LA
Two M3 (length 25 mm 0.984 in)
screws with washers are attached.
Two M3 (length 20 mm 0.787 in)
screws with washers are attached.
Note: 2 sets are required to mount
the emitter/receiver.
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1114
ORDER GUIDE
FIBER
SENSORS
LASER
Controllers
SENSORS
PHOTO-
ELECTRIC
SENSORS
Type
Appearance
Model No.
Output
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
NPN open-collector transistor
(Judgment output)
Current/voltage output
(Linear output)
SENSORS
HL-AC1
SAFETY LIGHT
CURTAINS
SAFETY
/
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PNP open-collector transistor
(Judgment output)
Current/voltage output
(Linear output)
PARTICULAR
USE
HL-AC1P
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
Calculation unit
WIRE-SAVING
SYSTEMS
Appearance
Model No.
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
HL-AC1-CL
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
OPTIONS
ENERGY
MANAGEMENT
SOLUTIONS
Side-view attachment
FA
COMPONENTS
Designation
Model No.
Description
• HL-T1SV1
• HL-T1SV2
MACHINE
VISION
SYSTEMS
For HL-T1001A(F) /
T1005A(F) (1 pc.)
HL-T1SV1
UV
The beam axis can be bent to a right
angle making universal mounting
possible.
Side-view
attachment
CURING
SYSTEMS
For HL-T1010A(F)
(1 pc.)
HL-T1SV2
Controller
mounting bracket
Use when mounting the controller with screws.
MS-HLAC1-1
HL-T1CCJ4
HL-T1CCJ8
Selection
Guide
Extension cable for use between the controller
Length: 4 m 13.123 ft
Net weight: 162 g approx.
Laser
and its cable linking it with the sensor head.
Cabtyre cable with connectors on both ends
Cable outer diameter: ø5.2 mm ø0.205 in
Connector outer diameter:
Displacement
Mounted on both sides
Mounted on one side only
Magnetic
Extension cable
Displacement
Length: 8 m 26.247 ft
Net weight: 330 g approx.
Contact
Displacement
Controller mounting bracket
• MS-HLAC1-1
ø15.5 mm ø0.610 in max.
Collimated
Beam
Sensors
Metal-sheet
Double-feed
Detection
Digital Panel
Controller
Other
Products
HL-T1
LD
LA
Extension cable
• HL-T1CCJ4
• HL-T1CCJ8
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1115
SPECIFICATIONS
FIBER
SENSORS
LASER
Sensor heads
SENSORS
PHOTO-
ELECTRIC
SENSORS
Type
Beam diameter ø1 mm ø0.039 in type Sensing width 5 mm 0.197 in type Sensing width 10 mm 0.394 in type
IEC / JIS conformed type
FDA conformed type
HL-T1001A
HL-T1001F
HL-T1005A
HL-T1010A
HL-T1010F
MICRO
PHOTO-
ELECTRIC
SENSORS
Item
HL-T1005F
EMC Directive, RoHS Directive
HL-AC1, HL-AC1P
CE marking directive compliance
Applicable controller
Sensing range
AREA
SENSORS
SAFETY LIGHT
CURTAINS
/
0 to 500 mm 0 to 19.685 in 500 to 2,000 mm 19.685 to 78.74 in
500 mm 19.685 in
SAFETY
COMPONENTS
Sensing width
ø1 mm ø0.039 in
ø1 to ø2.5 mm ø0.039 to ø0.098 in
5 mm 0.197 in
10 mm 0.394 in
PRESSURE /
FLOW
ø8 µm ø0.315 mil ø50 µm ø1.969 mil
Min. sensing object
ø0.05 mm ø0.002 in opaque object
ø0.1 mm ø0.004 in opaque object
SENSORS
opaque object
opaque object
INDUCTIVE
PROXIMITY
SENSORS
Repeatability
(During the state in which light is half blocked)
4 µm 0.157 mil
(Note 2)
4 µm 0.157 mil (Note 2)
4 µm 0.157 mil (Note 2)
Green LED (lights up during laser emission)
PARTICULAR
USE
Linear output resolution
(Note 3)
4 µm 0.157 mil
(Note 2, 4)
SENSORS
SENSOR
OPTIONS
Emission indicator
Interference prevention function
Pollution degree
Two units of sensors can be mounted close together. (When the controller interference prevention function is used)
3 (industrial environment)
SIMPLE
WIRE-SAVING
UNITS
Ambient temperature
Ambient humidity
0 to +50 °C +32 to +122 °F (No dew condensation allowed), Storage: –25 to +70 °C –13 to +158 °F
35 to 85 % RH, Storage: 35 to 85 % RH
WIRE-SAVING
SYSTEMS
Ambient illuminance
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Incandescent light: 10,000 ℓx or less at the light-receiving face
MEASURE-
MENT
1,000 V AC for one min. between all supply terminals connected together and enclosure
100 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Red semiconductor laser Class 1 (IEC / JIS)
Red semiconductor laser Class 1 (IEC / JIS)
modulated, max. output: 0.2 mW, peak
emission wavelength: 650 nm 0.026 mil
modulated, max. output: 0.35 mW,
peak emission wavelength: 650 nm 0.026 mil
IEC / JIS conformed type
FDA conformed type
PLC
HUMAN
MACHINE
INTERFACES
Red semiconductor laser Class II (FDA)
Red semiconductor laser Class II (FDA)
ENERGY
MANAGEMENT
SOLUTIONS
modulated, max. output: 0.35 mW,
peak emission wavelength: 650 nm 0.026 mil
modulated, max. output: 0.2 mW, peak
emission wavelength: 650 nm 0.026 mil
(IEC / JIS: Class 1)
(IEC / JIS: Class 1)
FA
COMPONENTS
Material
Enclosure: Polyetherimide, Case cover: Polycarbonate, Front cover: Glass
0.09mm2 3-core shielded cable with connector, 0.5 m 1.640 ft long
Extension up to total 10 m 32.808 ft is possible, with the optional cable.
MACHINE
VISION
Cable
SYSTEMS
Cable extension
Net weight
UV
CURING
Emitter: 15 g approx., Receiver: 15 g approx.
Emitter: 30 g approx., Receiver: 20 g approx.
SYSTEMS
MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both
the emitter and the receiver
CN-HLT1-1(Sensor head to controller connection cable): 1 cable
Laser beam alignment sticker: 2 pcs.
MS-LA3-1 (Sensor head mounting bracket):
One set of two brackets for both the emitter and the receiver
CN-HLT1-1 (Sensor head to controller connection cable): 1 cable
Laser beam alignment sticker: 2 pcs.
Label set (FDA conformed type only): 1 set
Accessories
Label set (FDA conformed type only): 1 set
Selection
Guide
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
2) In case of an average sampling rate of 64 times.
Laser
Displacement
3) Value calculated with the linear output allowance factor (±3 σ) when connected to the controller included in the calculation of the detection width.
4) This value was obtained by converting the range of linear output fluctuation (±3 σ) into a sensing width, assuming that the smallest sensing object
blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.
Magnetic
Displacement
Contact
Displacement
Collimated
Beam
Calculation unit
Sensors
Metal-sheet
Double-feed
Detection
Model No.
HL-AC1-CL
Digital Panel
Controller
Item
Other
Products
CE marking directive compliance
Connected controller
Current consumption
Connecting method
Connection indicator
Ambient temperature
Ambient humidity
Voltage withstandablity
Insulation resistance
Vibration resistance
Shock resistance
EMC Directive, RoHS Directive
HL-AC1, HL-AC1P
12 mA or less (supplied from the controller)
HL-T1
LD
Connector
Orange LED (lights up when connected to the controller)
0 to +50 °C +32 to +122 °F (No dew condensation allowed), Storage: –15 to +60 °C +5 to +140 °F
35 to 85 % RH, Storage: 35 to 85 % RH
LA
1,000 V AC for one min. between all supply terminals connected together and enclosure
100 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.7 mm 0.028 in double amplitude in X, Y and Z directions for 80 min.
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Enclosure: ABS, Indicator part: Acrylic
Material
Weight
Net weight: 50 g approx.
Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1116
SPECIFICATIONS
FIBER
SENSORS
LASER
Controllers
SENSORS
PHOTO-
Type
NPN output
PNP output
ELECTRIC
SENSORS
Item
Model No.
HL-AC1
HL-AC1P
MICRO
PHOTO-
ELECTRIC
SENSORS
CE marking directive compliance
Applicable sensor head
Supply voltage / Current consumption
Measuring cycle
EMC Directive, RoHS Directive
HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F
12 to 24 V DC ±10 % Ripple P-P 10 % or less / 190 mA or less (when connected to the sensor head)
150 μs
AREA
SENSORS
SAFETY LIGHT
CURTAINS
SAFETY
/
Current / voltage output switchable (Note 2)
COMPONENTS
• During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ω
• During voltage output: ±4 V/F.S., Output impedance 100 Ω
(In the monitor focus function, it can also be set at ±5 V, 0 to 5 V, etc.)
Linear output
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Temperature characteristics
±0.2 % F.S./°C (Note 3)
Settable average sampling rate (Note 4)
1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096
PARTICULAR
USE
NPN open-collector transistor
• Maximum sink current: 50 mA
Applied voltage: 30 V DC or less (between judgment output and 0 V)
• Residual voltage: 1.2 V or less (at 50 mA sink current)
PNP open-collector transistor
• Maximum source current: 50 mA
SENSORS
Judgment outputs
(HIGH, PASS, LOW)
•
•
Applied voltage: 30 V DC or less (between judgment output and +V)
SENSOR
OPTIONS
• Residual voltage: 2 V or less (at 50 mA source current)
Utilization category
Number of outputs
DC-12 or DC-13
SIMPLE
WIRE-SAVING
UNITS
HIGH / PASS / LOW 3 values output
HIGH: ON when measured value > HIGH threshold value
PASS: ON when HIGH threshold value ≥ measured value ≥ LOW threshold value
LOW: ON when LOW threshold value > measured value
WIRE-SAVING
SYSTEMS
Output operation
Short-circuit protection
Laser OFF input
MEASURE-
MENT
Incorporated
SENSORS
0 V connection: Laser emission halt
Open: Laser emission
• Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
+V connection: Laser emission halt
Open: Laser emission
• Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
STATIC
CONTROL
DEVICES
LASER
0 V connection: Zero reset operates
Open: Zero reset ineffective
+V connection: Zero reset operates
Open: Zero reset ineffective
MARKERS
Zero reset input
Timing input
• Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
• Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
PLC
0 V connection: Effective
Open: Ineffective
• Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
+V connection: Effective
Open: Ineffective
• Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
HUMAN
MACHINE
INTERFACES
0 V connection: Effective
Open: Ineffective
• Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
+V connection: Effective
Open: Ineffective
• Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
ENERGY
Reset input
MANAGEMENT
SOLUTIONS
Laser emitting (LD ON)
Judgment outputs
Green LED (lights up during laser emission)
HIGH: Orange LED (lights up when measured value > HIGH threshold value)
PASS: Green LED (lights up when HIGH threshold value measured value LOW threshold value)
FA
COMPONENTS
MACHINE
VISION
≥
≥
LOW: Yellow LED (lights up when LOW threshold value measured value)
>
SYSTEMS
Enable (ENABLE)
Zero reset (ZERO)
Green LED (lights up during normal operation)
UV
CURING
SYSTEMS
Green LED (lights up when the zero reset function is enabled)
RUN mode: Either the measured value (mm) or the hold value will be displayed.
Reverse mode: The display orientation will be reversed.
Main digital display
Sub-digital display
5 digit red LED display
RUN mode: Either the resolution or laser beam reception amount will be displayed.
THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.
5 digit yellow LED display
Selection
Guide
Laser
• Measured value
display
• Setting value, light
amount value
resolution display
• Standard received light • Bottom hold
setting
• Automatic scaling
• Scaling
• Display reverse
• ECO display
• Display digits limitation • ON-delay timer
• Sample hold
• Peak hold
• Zero reset
• Initial reset
• Positioning teaching
• 2-point teaching
• Automatic teaching
• Hysteresis width variability
• Monitor focus
• (A + B) calculation
(Note 5)
• Mutual interference
prevention (Note 5)
• Laser deterioration
detection
Displacement
Magnetic
Displacement
• OFF-delay timer
• One-shot timer
• Differentiation
• Sensitivity selection
• Threshold value direct • (A – B) calculation
Contact
Displacement
Main functions
Collimated
• Non-measuring time
setting
Beam
Sensors
• Peak to peak hold
• Self peak hold
• Self bottom hold
• Key lock
• Zero reset memory
Metal-sheet
Double-feed
Detection
setting
(Note 5)
Digital Panel
Controller
Pollution degree
Ambient temperature
Ambient humidity
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Material
3 (industrial environment)
Other
Products
0 to +50 °C +32 to +122 °F (No dew condensation allowed), Storage: –25 to +65 °C –13 to +149 °F
35 to 85 % RH, Storage: 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.7 mm 0.028 in double amplitude in X, Y and Z directions for 80 min.
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Enclosure: Polybutylene terephthalate, Transparent cover: Polycarbonate
0.09 mm2 10-core composite cable, 2 m 6.562 ft long
HL-T1
LD
LA
I/O cable
I/O cable extension
Weight
Extension up to total 10 m 32.808 ft is possible, with 0.09 mm2 or more, cable. (Note 6)
Net weight: 140 g approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
2) Switching between current and voltage is accomplished by a switch on the bottom of the controller.
3) This is a typical value when the sensor head is connected.
4) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) × (Set average sampling rate + 1).
5) The calculation unit is necessary.
6) If the extension cable is longer than 10 m 32.808 ft, then it will not qualify for CE marking.
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1117
FIBER
I/O CIRCUIT DIAGRAMS
SENSORS
LASER
SENSORS
NPN output type
PNP output type
HL-AC1
HL-AC1P
PHOTO-
ELECTRIC
SENSORS
Color code
(Brown) +V
Color code
(Brown) +V
MICRO
PHOTO-
D
D
(White) HIGH
judgment output
Tr1
ELECTRIC
SENSORS
Load
50 mA max.
Tr1
Load
(White) HIGH judgment output
50 mA max.
(Green) PASS judgment output
AREA
Tr2
Load
ZD1
ZD1
Load
50 mA max.
SENSORS
+
+
–
12 to 24 V DC
Tr2
12 to 24 V DC
±10 %
±10 %
(Green) PASS judgment output
–
SAFETY LIGHT
50 mA max.
(Gray) LOW judgment output
Tr3
Load
Load
ZD2
ZD2
CURTAINS
/
50 mA max.
Tr3
SAFETY
COMPONENTS
(Gray) LOW judgment output
50 mA max.
PRESSURE /
FLOW
ZD3
(Blue) GND (0 V)
(Blue) GND (0 V)
ZD3
SENSORS
(Pink) LD-OFF input
* 1
* 1
* 1
* 1
(Pink) LD-OFF input
(Violet) Timing input
(Orange / Violet) Zero reset input
(Red) Reset input
* 1
* 1
* 1
* 1
INDUCTIVE
PROXIMITY
SENSORS
(Violet) Timing input
(Orange / Violet) Zero reset input
(Red) Reset input
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
Current output
4 to 20 mA
Current output
4 to 20 mA
(Black) Linear output
(Black) Linear output
Current output:
300 Ω or less
Voltage output:
10 kΩ or more
SIMPLE
WIRE-SAVING
UNITS
Current output:
300 Ω or less
Voltage output:
10 kΩ or more
Voltage
output ±4 V
Voltage
output ±4 V
Load
Load
100Ω
100Ω
(Shield) Linear GND
Users’ circuit
(Shield) Linear GND
WIRE-SAVING
SYSTEMS
Internal circuit
Internal circuit
Users’ circuit
MEASURE-
MENT
Symbols … D: Reverse supply polarity protection diode
Symbols … D: Reverse supply polarity protection diode
ZD1, ZD2, ZD3: Surge absorption zener diode
Tr1, Tr2, Tr3: PNP output transistor
SENSORS
ZD1, ZD2, ZD3: Surge absorption zener diode
Tr1, Tr2, Tr3: NPN output transistor
STATIC
CONTROL
DEVICES
* 1
* 1
LASER
Non-voltage contact or NPN open-collector transistor
Non-voltage contact or PNP open-collector transistor
MARKERS
or
or
PLC
HUMAN
MACHINE
• LD-OFF input, Timing input, Zero reset input, Reset inpu
Low (0 to 1.5 V): Effective
t
• LD-OFF input, Timing input, Zero reset input, Reset inpu
Low (0 V or open): Ineffective
t
INTERFACES
High (+V or open): Ineffective
High [ +V to ( +V –1.5 V)]: Effective
ENERGY
MANAGEMENT
SOLUTIONS
FA
SENSING CHARACTERISTICS (TYPICAL)
COMPONENTS
MACHINE
VISION
SYSTEMS
HL-T1001A HL-T1001F
HL-T1005A HL-T1005F
UV
CURING
SYSTEMS
Correlation between transverse
deviation and output voltage
Correlation between transverse
deviation and output voltage
Correlation between interrupted
beam width and output voltage
8
8
8
Horizontal direction
2 m 6.562 ft
Vertical direction
250 mm 9.843 in
Sensing object
Horizontal direction
500 mm 19.685 in
Vertical direction
2 m 6.562 ft
500 mm 19.685 in
Receiver
Receiver
Emitter
ℓ
Receiver
+
Receiver
Receiver
Emitter
Emitter
ℓ
ℓ
Emitter
Emitter
6
4
2
0
ℓ
6
4
2
ℓ
6
4
2
0
Selection
Guide
–
500 mm
19.685 in
Laser
The graph depicts the
correlation between
transverse deviation and
output voltage when the
full-scale setting ranges
from 0 V (light beam is
interrupted) to 5 V (light
beam is fully incident),
using the Monitor Focus
function.
Vertical direction
Horizontal direction
Displacement
Vertical direction
Horizontal direction
Magnetic
Displacement
Contact
The graph depicts the correlation between
transverse deviation and output voltage when
the full-scale setting ranges from 0 V (light
beam is interrupted) to 5 V (light beam is fully
incident), using the Monitor Focus function.
Displacement
Collimated
Beam
Sensors
Metal-sheet
Double-feed
Detection
0
4
2
0.079
0
2
0.079
4
0.157
10
0.394
5
0.197
0
5
10
0.394
Right (Down)
–10
–5
0
5
0.197
10
0.394
0.157
0.197
–0.394 –0.197
Digital Panel
Controller
(Up) Left
Center
Deviation ℓ (mm in)
Right (Down)
(Up) Left
Center
Screeing edge position ℓ (mm in)
Deviation ℓ (mm in)
Other
Products
HL-T1010A HL-T1010F
HL-T1
LD
Correlation between transverse
deviation and output voltage
Correlation between interrupted
beam width and output voltage
8
8
250 mm 9.843 in
Sensing object
Horizontal direction
500 mm 19.685 in
Vertical direction
LA
500 mm 19.685 in
+
Receiver
Receiver
ℓ
Emitter
Receiver
Emitter
Emitter
6
4
2
ℓ
ℓ
6
4
2
0
–
500 mm 19.685 in
Vertical direction
Horizontal direction
The graph depicts the correlation
between transverse deviation
and output voltage when the
full-scale setting ranges from 0 V
(light beam is interrupted) to 5 V
(light beam is fully incident),
using the Monitor Focus function.
0
10
0.394
5
0.197
0
5
10
0.394
Right (Down)
–10
–5
0
5
0.197
10
0.394
0.197
–0.394 –0.197
(Up) Left
Center
Deviation ℓ (mm in)
Screeing edge position ℓ (mm in)
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1118
PRECAUTIONS FOR PROPER USE
FIBER
Refer to p.1595 for general precautions and p.1593~ for information about laser beam.
SENSORS
LASER
SENSORS
Functions
• This catalog is a guide to select a suitable product. Be
sure to read instruction manual attached to the product
prior to its use.
PHOTO-
ELECTRIC
SENSORS
Function
Details
MICRO
PHOTO-
ELECTRIC
SENSORS
The following tasks can be done by executing zero
reset.
• The display value can be set at “0”.
• The linear output when the display reads “0” is
made the center output value of the 2 points set
by monitor focus. (In the default state, the current
output is 12 mA and the voltage output is 0 V.)
AREA
• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
Zero reset
function
SENSORS
SAFETY LIGHT
CURTAINS
SAFETY
/
COMPONENTS
PRESSURE /
FLOW
The auto scaling function selects whether to display
the laser beam reception amount in the main-digital
display in “mm” units or in “%” units, and determines
whether the amount of laser beam received or the
amount of laser beam interrupted is displayed. With
the set standard laser beam reception amount as the
reference value, the current laser beam reception
amount (laser beam interrupted amount) is scaled
automatically and is displayed as well as being
output.
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Auto scaling
function
PARTICULAR
USE
SENSORS
• This product is classified as a Class 1 Laser
Product in IEC / JIS regulations and a Class
II Laser Product in FDA regulations. Do not
look at the laser beam through optical
system such as a lens.
• The following label is attached to the
product. Handle the product according to the
instruction given on the warning label.
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
This function registers and stores the current laser
beam reception amount in memory as the standard
laser beam reception amount. The laser beam
reception amount during full laser beam entry
becomes the 100 % laser beam reception amount’s
full scale (F.S.). If this function is used, the display
and the linear output are set on the full scale (F.S.)
automatically. It can also be used to correct the laser
beam reception amount when there is a change in
the laser beam reception amount due to dirt, etc. on
the front glass.
WIRE-SAVING
SYSTEMS
Standard
received light
setting
MEASURE-
MENT
SENSORS
The English warning label based
on FDA regulations is pasted on
the FDA conformed type.
STATIC
CONTROL
DEVICES
LASER
MARKERS
The scaling function is a function that changes the
display value to the desired amount with respect to
the setting value. At the desired distance, the display
value can be input and changed.
PLC
Safety standards for laser beam products
Scaling function
HUMAN
• A laser beam can harm human being’s eyes, skin, etc.,
because of its high energy density. IEC has classified
laser products according to the degree of hazard and the
stipulated safety requirements.
MACHINE
INTERFACES
Hysteresis width
setting function
This function sets the hysteresis to the desired value.
ENERGY
MANAGEMENT
SOLUTIONS
With this function, the linear output range and
inclination, etc. with respect to the display value can
be specified. Setting is done by determining the 2
output values with respect to the desired display
values.
The HL-T1 series is classified as Class 1 laser.
FA
Monitor focus
function
COMPONENTS
Classification by IEC 60825-1
MACHINE
VISION
SYSTEMS
This function makes the amount of change in the
measured value an output value. Use this function
when measuring if you are paying attention to
changes in measured values, as when counting the
number of workpieces, etc.
Classification
Description
UV
CURING
SYSTEMS
Differential
function
Lasers that are safe under reasonably foreseeable conditions of operation,
including the use of optical instruments for intrabeam viewing.
Class 1
The digital display’s direction can be selected. The
forward direction or the reverse direction to match
the direction of installation on the equipment can be
selected.
Display reverse
function
Safe use of laser products
Selection
Guide
• For the purpose of preventing users from suffering
injuries by laser products, IEC 60825-1 “Safety of laser
products”. Kindly check the standards before use.
(Refer to p.1593~ for information about laser beam.)
Laser
Displacement
ECO display
function
This function makes the display dark and saves
electric power.
Magnetic
Displacement
Contact
This determines the number of display digits in the
main-digital and sub-digital displays. If the number of
digits is limited, the digits are turned off beginning
with the lowest order digit.
Displacement
Display digits
limitation function
Collimated
Beam
Sensors
Metal-sheet
Double-feed
Detection
This selects whether or not to save the zero reset
level in memory when the power is turned OFF. If
you desire to reproduce the zero reset level from the
previous operating session when you turn the power
ON again, then enable this function. If this function is
enabled, the zero reset level data are written into the
EEPROM each time.
Digital Panel
Controller
Other
Products
Zero reset memory
function
HL-T1
LD
The controller’s key input can be disabled. Once the
key input is disabled, the controller will not accept
any key inputs until the key lock is released. Use this
function to avoid changing the setting by mistake.
Key lock
function
LA
Connection
• This product is made to satisfy the specifications when the
sensor head is combined with the controller. In any other
combination, not only may it not satisfy the specifications,
but could be the cause of breakdown. So by all means,
use it so that there is a combination of the sensor head
and the controller.
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1119
FIBER
PRECAUTIONS FOR PROPER USE
Refer to p.1595 for general precautions and p.1593~ for information about laser beam.
SENSORS
LASER
Functional description
SENSORS
①
⑥
⑤
③
⑫
⑨ ⑪
PHOTO-
ELECTRIC
SENSORS
②
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS
/
SAFETY
COMPONENTS
PRESSURE /
FLOW
⑬
Function
④
⑧
⑩
⑦
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Description
PARTICULAR
USE
Laser emitting indicator
(LD ON)
SENSORS
Lights up when the sensor head is emitting laser beam.
(Green LED)
SENSOR
OPTIONS
HIGH: Orange LED (lights up when measured value HIGH threshold value)
PASS: Green LED (lights up when HIGH threshold value measured value LOW threshold value)
LOW: Yellow LED (lights up when LOW threshold value measured value)
Judgment output indicators
(HIGH / PASS / LOW)
(Orange / Green / Yellow LED)
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
When in the RUN mode, it displays the measured value (mm/%).
During measurement hold, it displays the hold value (mm/%).
In Reverse mode, the top and bottom are displayed in reverse.
Main digital display
(5 digit red LED)
MEASURE-
MENT
SENSORS
When in the RUN mode, it displays the threshold value, voltage / current value, light reception
amount or resolution. When in the THR mode, it displays the respective threshold values. In
reverse mode, the top and bottom are displayed in reverse.
STATIC
CONTROL
DEVICES
Sub-digital display
(5 digit yellow LED)
LASER
MARKERS
Enable indicator
(ENABLE)
Lights up when operation is normal. Goes off when operation is abnormal
(if the sensor head is not connected when the power is turned on).
(Green LED)
PLC
Zero reset indicator
(ZERO)
(Green LED)
HUMAN
MACHINE
Lights up when the zero reset function is enabled.
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
The following 3 modes can be selected.
•RUN mode: Measuring mode
•THR mode: The threshold values are set in this mode.
•FUN mode: Each of the settings are set in this mode.
Mode selection switch
FA
COMPONENTS
MACHINE
VISION
Threshold value select
switch
When in the THR / RUN mode, this switches the set threshold value (HIGH / LOW).
SYSTEMS
UV
CURING
•RUN mode: Timing input
•THR mode: Changes the threshold value (forward direction)
•FUN mode: Changes the function setting value (forward direction)
UP key
SYSTEMS
•RUN mode: Press for 3 sec. or more: Standard light reception amount setting input
•THR mode: Changes the threshold value (reverse direction)
DOWN key
RIGHT key
LEFT key
•FUN mode: Changes the function setting value (reverse direction)
Selection
Guide
•RUN mode: Changes the contents of the sub-digital display (forward direction)
•THR mode: Changes the threshold value digit (forward direction)
•FUN mode: Sets function selection (forward direction)
Laser
Displacement
Magnetic
Displacement
•RUN mode: Changes the contents of the sub-digital display (reverse direction)
•THR mode: Changes the threshold value digit (reverse direction)
•FUN mode: Sets function selection (reverse direction)
Contact
Displacement
Collimated
Beam
Sensors
Metal-sheet
Double-feed
Detection
•RUN mode: Pressing for 1 sec. or more, executes zero reset. Pressing together with the RIGHT
key for 3 sec. or more, cancels zero reset.
ENT key
Digital Panel
Controller
•THR mode: When threshold value is blinking, the threshold value is set. When the threshold
value lights up, teaching is executed.
Other
Products
•FUN mode: When the set value is blinking, the value is set.
When the setting is being initialized, pressing for a long time executes initialization.
HL-T1
LD
Others
• This product outputs the judgment of the laser light analog
quantity. Since there is variation in the light intensity between
the center and the edges of the detection area, and the
emitter side and the receiver side, the “display value” does
not equal “the actual dimensions”, so caution is necessary.
Use the displayed dimensional value as a criterion.
LA
• If the object being measured has a mirror surface or is
a transparent body, it may be impossible to measure it
accurately, so please exercise caution.
• Absolutely do not attempt to disassemble this product.
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1120
DIMENSIONS (Unit: mm in)
FIBER
The CAD data can be downloaded from our website.
Sensor head
SENSORS
LASER
SENSORS
HL-T1001A(F) HL-T1005A(F)
PHOTO-
ELECTRIC
SENSORS
2-ø3.2 ø0.126
2-ø3.2 ø0.126
ø2.6 ø0.102 cable, 0.5 m 1.640 ft long (Black)
Manufactured by
2.8
0.110
34
1.339
MICRO
ø2.6 ø0.102 cable,
0.2 0.008
PHOTO-
ELECTRIC
SENSORS
19
0.748
0.5 m 1.640 ft long (Gray)
16
0.630
(1.5) (0.059)
J.S.T. Mfg. Co., Ltd.
XARR-04VF*
2.8
0.110
5 0.197
9
AREA
15
9
0.354 0.591
SENSORS
15
SAFETY LIGHT
0.591 0.354
CURTAINS
SAFETY
/
Manufactured by
J.S.T. Mfg. Co., Ltd.
XARR-04VF*
(36.5)
(1.437)
COMPONENTS
(6.9)
(0.272)
*
The sensor heads that were produced before January 2006 use the connector shown below.
Please note that the new connector and previous connector are incompatible.
PRESSURE /
FLOW
Certification / identification label (Note 1)
SENSORS
(50 µm 1.969 mil polyester film)
INDUCTIVE
PROXIMITY
SENSORS
(10)
(0.394)
Manufactured by Molex
51029-0410
Light beam shielding plate (Note 1)
PARTICULAR
USE
Emission indicator (Green)
SENSORS
Beam axis (Note 2)
15
0.591
SENSOR
OPTIONS
15
0.591
SIMPLE
Emitter
WIRE-SAVING
UNITS
Receiver
Notes: 1) IEC / JIS conforming products do not contain light beam shielding plate,
or certification / identification label.
WIRE-SAVING
SYSTEMS
2) The receiver of HL-T1001A(F) does not incorporate a slit.
MEASURE-
MENT
SENSORS
Sensor head
HL-T1010A HL-T1010F
STATIC
CONTROL
DEVICES
2-ø3.2 ø0.126
2-ø3.2 ø0.126
LASER
ø2.6 ø0.102 cable, 0.5 m 1.640 ft long (Black)
42
1.654
2.8
0.110
0.2
0.008
MARKERS
ø2.6 ø0.102 cable,
25
0.984
2.8
0.110
Manufactured by
J.S.T. Mfg. Co., Ltd.
XARR-04VF*
0.5 m 1.640 ft long (Gray)
10
0.394
(6.9)(0.272)
PLC
14
0.551
20
0.787
14
0.551
20
0.787
HUMAN
MACHINE
INTERFACES
Manufactured by
J.S.T. Mfg. Co., Ltd.
XARR-04VF*
22
0.866
ENERGY
(36.5)
(1.437)
(1.5)
(0.059)
* The sensor heads that were produced before January 2006 use the connector shown below.
Please note that the new connector and previous connector are incompatible.
MANAGEMENT
SOLUTIONS
Certification / identification label (Note)
(50 μm 1.969 mil polyester film)
FA
COMPONENTS
(10)
(0.394)
Manufactured by Molex
51029-0410
MACHINE
VISION
SYSTEMS
Light beam shielding plate (Note)
Emission indicator
)
(
Green
Beam axis
UV
CURING
SYSTEMS
20
0.787
20
0.787
Emitter
Receiver
Selection
Guide
Note: IEC / JIS conforming products do not contain light beam shielding
Laser
plate, or certification/identification label.
Displacement
Magnetic
Displacement
Controller
Calculation unit (Optional)
HL-AC1 HL-AC1P
HL-AC1-CL
Contact
Displacement
Collimated
Beam
Mounting drawing with a mounting bracket MS-HLAC1-1 (Optional)
Sensors
Metal-sheet
Double-feed
Detection
Connector for calculation unit
connection (on each side)
Linking connector
24.9
Digital Panel
Controller
0.980
32.2 1.268
30 1.181
(3.6)
64.3
Other
Products
(0.142)
2.531
Connection indicator (Orange)
4.3
34.3
0.169
1.350
15.1
0.594
HL-T1
LD
15.8
13.2
0.622
0.520
57 2.244
54.9 2.161
12 0.472
8 0.315
22.4
16
ø5.2 ø0.205 cable,
2 m 6.562 ft long
3.9
LA
0.882
0.630
0.154
13
36.8
30
26
Suitable for 35 mm 1.378 in
width DIN rail
0.512
2-ø3.2 ø0.126
1.449
1.181
1.024
5.4
36.7
5
150 5.906 approx.
0.213
3.4
1.445
0.197
03.1.344
3.4 0.134
0.134
ø5.1 ø0.201 cable
Suitable for 35 mm 1.378 in
width DIN rail
32.2
1.268
16.1
0.634
Connector for
sensor head connection
5.4 0.213
22.4 16
0.882 0.630
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1121
FIBER
DIMENSIONS (Unit: mm in)
The CAD data can be downloaded from our website.
SENSORS
LASER
SENSORS
Sensor head mounting bracket for HL-T1001A(F) / HL-T1005A(F) [Accessory for HL-T1001A(F) / HL-T1005A(F)]
MS-HLT1-1
PHOTO-
ELECTRIC
SENSORS
Assembly dimensions
3.4
0.134
15
1
2
0.591
6
7
5
1.1
9
MICRO
PHOTO-
Mounting drawing with HL-T1005A’s receiver
0.236
0.276 0.197
9
ø3.2 ø0.126
0.043
0.354
ELECTRIC
SENSORS
0.354
AREA
3.2 0.126
9
SENSORS
0.354
3.4
2-M3
×
0.5 0.020
t 1.6
SAFETY LIGHT
5
0.134
12.5
3.2
CURTAINS
/
14.5
(34.6)
0.197
0.492
SAFETY
0.126
0.571
1.6 0.063
3.4 0.134
(1.362)
COMPONENTS
5 0.197
5 0.197
PRESSURE /
FLOW
9
0.354
10
t 0.063
SENSORS
13.1
0.516
9
0.394
3 0.118
INDUCTIVE
PROXIMITY
SENSORS
1.1
3.4 0.134
1.6 0.063
0.043
0.354
2-ø3.2 ø0.126
1.1 0.043
5
9 0.354
0.197
PARTICULAR
USE
5
5 0.197
0.197
SENSORS
3.4 0.134
9
5
SENSOR
OPTIONS
17
0.669
t 1.2
3.2
0.354
17
t 0.047
0.126
7
0.669
0.374
9.5
0.276
SIMPLE
WIRE-SAVING
UNITS
5
17
17
13.1
ø3.2 ø0.126
0.197
0.669
0.197
t 1.2
t 0.047
0.669
0.516
3.4
24.5
WIRE-SAVING
SYSTEMS
0.134
0.965
Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)
MEASURE-
MENT
Two M3 (length 20 mm 0.787 in) screws with washers are attached.
SENSORS
STATIC
CONTROL
DEVICES
Sensor head mounting bracket for HL-T1010A(F) [Accessory for HL-T1010A(F)
]
MS-LA3-1
LASER
MARKERS
Assembly dimensions
1
2
Mounting drawing with HL-T1010A’s receiver
20
0.787
14
20
PLC
0.787
14
2-ø3.2 ø0.126
6
2-ø3.2 ø0.126
0.236
HUMAN
MACHINE
0.551
0.551
2.6
INTERFACES
6 0.236
13
0.102
0.512
ENERGY
MANAGEMENT
SOLUTIONS
3.4
2-M3 × 0.5 0.020
14
0.134
0.551
16
(45.1)
23
0.630
(1.776)
0.906
FA
2.6
3.4
COMPONENTS
0.102
0.134
t 1.6
t 0.063
14
0.551
2.6 0.102
MACHINE
VISION
3
14
10
0.118
2-ø3.2 ø0.126
0.551
SYSTEMS
0.394
3 0.118
2.6 0.102
3.4 0.134
UV
CURING
3.4
3.4 0.134
0.134
SYSTEMS
2.6 0.102
3
14
0.118
0.551
14
23
0.906
3.4
10
0.551
0.134
13
0.394
2.6
0.102
0.512
6 0.236
23
10
0.394
23
0.906
Selection
Guide
t 1.6
t 0.063
0.906
13
0.512
Laser
Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)
Displacement
Magnetic
Two M3 (length 25 mm 0.984 in) screws with washers are attached.
23
20
0.787
Displacement
0.906
t 1.6
t 0.063
Contact
33
Displacement
1.229
Collimated
Beam
Sensors
Metal-sheet
Double-feed
Detection
Controller mounting bracket (Optional)
Sensor head to controller connection cable (Accessory for sensor head)
MS-HLAC1-1
CN-HLT1-1
Digital Panel
Controller
+200
0
34.8
Other
Products
1,500
59.055
1.370
22
2-ø3.2 ø0.126
+7.874
0
46
1.811
Gray
0.866
16
3
2.5
ø15
ø0.591
0.118
0.098
0.630
HL-T1
LD
Manufactured by Hirose
7.3
0.287
Black
ø2.6 ø0.102 × 2
Manufactured by J.S.T. Mfg. Co., Ltd. XAP-04V-1*
Electric Co.,Ltd. RP17-13P-12PC
3
3
26.8
1.055
16
0.118
0.118
LA
* The sensor heads that were produced
before January 2006 use the connector
shown below.
0.630
3.4
5.4
5.3
0.134
0.213
0.209
Please note that the new connector and
previous connector are incompatible.
5.4
0.213
32.2 27.2
27.2
1.268 1.071
1.071
3.4
0.134
Manufactured by
Molex 51030-0430
t 1.0
t 0.039
Ultra-compact Laser Collimated Beam Sensor HL-T1 SERIES
1122
DIMENSIONS (Unit: mm in)
FIBER
The CAD data can be downloaded from our website.
SENSORS
LASER
SENSORS
Side-view attachment for HL-T1001A(F) / HL-T1005A(F) (Optional)
HL-T1SV1
PHOTO-
Assembly dimensions
ELECTRIC
SENSORS
Mounting drawing with HL-T1005A’s receiver
MICRO
PHOTO-
ELECTRIC
SENSORS
2.7
0.106
AREA
15
15
SENSORS
0.591
0.591
SAFETY LIGHT
CURTAINS
SAFETY
/
COMPONENTS
(34)
Beam axis
(1.339)
2-ø2.2 ø0.087
Beam axis
PRESSURE /
FLOW
15
19
0.748
0.591
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
15
15
10.6
0.591
0.591 0.417
PARTICULAR
USE
7.5
0.295
15
0.591
12.5
0.492
2.2
SENSORS
0.087
SENSOR
OPTIONS
Material: Polyetherimide (Enclosure), Glass (Front cover)
SIMPLE
WIRE-SAVING
UNITS
Two M2 (length 6 mm 0.236 in) screws with washers are attached.
WIRE-SAVING
SYSTEMS
Side-view attachment for HL-T1010A(F) (Optional)
HL-T1SV2
MEASURE-
MENT
Assembly dimensions
SENSORS
STATIC
Mounting drawing with HL-T1010A’s receiver
CONTROL
DEVICES
LASER
MARKERS
20
2.8
0.787
0.110
PLC
HUMAN
(46)
20
MACHINE
INTERFACES
(1.811)
0.787
21
25
ENERGY
MANAGEMENT
SOLUTIONS
0.827
0.984
Beam axis
2-ø2.2 ø0.087
Beam axis
FA
COMPONENTS
20
20 15.6
MACHINE
VISION
0.787
0.787 0.614
SYSTEMS
UV
11
0.433
21
0.827
CURING
SYSTEMS
2.2
21
0.087
0.827
Material: Polyetherimide (Enclosure), Glass (Front cover)
Two M2 (length 6 mm 0.236 in) screws with washers are attached.
Selection
Guide
Laser
Displacement
Magnetic
Displacement
Contact
Displacement
Collimated
Beam
Sensors
Metal-sheet
Double-feed
Detection
Digital Panel
Controller
Other
Products
HL-T1
LD
LA
相关型号:
©2020 ICPDF网 联系我们和版权申明