MN101CF97D [PANASONIC]

MN101C97A;


型号：	MN101CF97D
厂家：	PANASONIC
描述：	MN101C97A 微控制器和处理器外围集成电路时钟
文件：	总4页 (文件大小：301K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MN101C97A, MN101C97D

Type

MN101C97A

MN101C97D

MN101CF97D

Internal ROM type

ROM (byte)

Mask ROM

FLASH

32K

64K

RAM (byte)

Package (Lead-free)

QFN044-P-0606A (Under planning), QFP044-P-1010F (Under planning), TQFP048-P-0707B

0.25 µs (at 2.2 V to 3.6 V, 8 MHz)

0.5 µs (at 1.8 V to 3.6 V, 4 MHz)*

62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*

Minimum Instruction

Execution Time

* The lower limit for operation guarantee for ﬂash memory built-in type is 2.0 V.

 Interrupts

RESET, Watchdog, External 0 to 5, External 6 (key interrupt dedicated), Timer 0 to 3, Timer 6, Timer 7 (2 systems), Time base, Serial

0 (2 systems), Serial 3, A/D conversion ﬁnish

 Timer Counter

Timer counter 0 : 8-bit × 1

(square-wave/8-bit PWM output, event count, generation of remote control carrier, simple pulse width measurement,

added pluse (2-bit) system PWM output)

(square-wave/PWM output to large current terminal P51 possible)

Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of

XI oscillation clock frequency; external clock input

Interrupt source ........... coincidence with compare register 0

Timer counter 1 : 8-bit × 1

(square-wave output, event count, synchronous output event, serial transfer clock output)

Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of

XI oscillation clock frequency; external clock input

Interrupt source ........... coincidence with compare register 1

Timer counter 0, 1 can be cascade-connected.

Timer counter 2 : 8-bit × 1

(square-wave output, added pluse (2-bit) system PWM output, PWM output, serial transfer clock output, event count,

synchronous output event, simple pulse width measurement)

(square-wave/PWM output to large current terminal P52 possible)

Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of

XI oscillation clock frequency; external clock input

Interrupt source ........... coincidence with compare register 2

Timer counter 3 : 8-bit × 1

(square-wave output, event count, generation of remote control carrier, serial transfer clock output)

Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of

XI oscillation clock frequency; external clock input

Interrupt source ........... coincidence with compare register 3

Timer counter 2, 3 can be cascade-connected.

Timer counter 6 : 8-bit freerun timer

Clock source................ 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of OSC oscillation clock frequency; 1/1, 1/128, 1/8192

of XI oscillation clock frequency

Interrupt source ........... coincidence with compare register 6

Timer counter 7 : 16-bit × 1

(square-wave output, 16-bit PWM output (cycle / duty continuous variable), event count, synchronous output event,

pulse width measurement, input capture, real time output control, high performance IGBT output)

(square-wave/PWM output to large current terminal P53 possible)

Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1,

1/2, 1/4, 1/16 of external clock input frequency

Interrupt source ........... coincidence with compare register 7 (2 lines), input capture register

MAD00058BEM

MN101C97A, MN101C97D

Timer counters 7, 8 can be cascade-connected.

(square-wave output, PWM input capture, pluse width measurement is possible as a 32-bit timer.)

Time base timer (one-minute count setting)

Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency

Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/4096, 1/8192, 1/16384, 1/32768, of clock source frequency

Watchdog timer

Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency

 Serial interface

Serial 0 : synchronous type/UART (full-duplex) × 1

Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of OSC

oscillation clock frequency, external clock

Serial 3 : synchronous type/single-master I²C × 1

Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3; 1/2, 1/4, 1/16, 1/32 of OSC

oscillation clock frequency, external clock

 I/O Pins

I/O

Common use , Speciﬁed pull-up resistor available, Input/output selectable (bit unit)

 A/D converter

10-bit × 8-ch. (with S/H)

 Special Ports

Buzzer output, remote control carrier signal output, high-current drive port

 ROM Correction

Correcting address designation : up to 3 addresses possible

 Electrical Charactreistics (Supply current)

Limit

typ

0.9

Parameter

Symbol

Condition

fosc = 4 MHz, VDD = 3 V

Unit

min

max

1.7

IDD1

IDD2

IDD3

IDD4

IDD5

IDD6

µA

Operating supply current

Supply current at HALT

Supply current at STOP

fx = 32 kHz, VDD = 3 V

fx = 32 kHz , VDD = 3 V, Ta = 25°C

fx = 32 kHz , VDD = 3 V , Ta = –40°C to +85°C

VDD = 3 V , Ta = 25°C

2.6

VDD = 3 V , Ta = –40°C to +85°C

 Development tools

In-circuit Emulator

PX-ICE101C/D+PX-PRB101C97-TQFP048-P-0707B-M

PX-ICE101C/D+PX-PRB101C97-QFP044-P-1010 (under planning)

MAD00058BEM

 Pin Assignment

P32, KEY2, TM2IO

P33, KEY3, TM3IO

P34, KEY4, TM7IO

P35, KEY5, NBUZZER

P36, KEY6, BUZZER

P37, KEY7

AN7, P07

AN6, P06

AN5, P05

AN4, P04

AN3, P03

MN101C97A

MN101C97D

AN2, P02

P40, SBI3

AN1, P01

P41, SBO3, SDA3

P42, SBT3, SCL3

P43, RXD0B, SBI0B

P44, , TXD0B, SBO0B

P45, SBT0B

AN0, P00

VREF+

LED4, P54

TM7O, LED3, P53

TM2O, LED2, P52

TQFP048-P-0707B

QFP044-P-1010F

QFN044-P-0606A

MAD00058BEM

Request for your special attention and precautions in using the technical information and

semiconductors described in this book

(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and

regulations of the exporting country, especially, those with regard to security export control, must be observed.

(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples

of the products, and no license is granted under any intellectual property right or other right owned by our company or any other

company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other

company which may arise as a result of the use of technical information described in this book.

(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office

equipment, communications equipment, measuring instruments and household appliances).

Consult our sales staff in advance for information on the following applications:

– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support

systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-

ucts may directly jeopardize life or harm the human body.

– Any applications other than the standard applications intended.

(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-

provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product

Standards in advance to make sure that the latest specifications satisfy your requirements.

(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions

(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute

maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any

defect which may arise later in your equipment.

Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure

mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire

or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.

(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,

thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which

damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.

(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita

Electric Industrial Co., Ltd. Industrial Co., Ltd.

MN101CF97D [PANASONIC]

相关型号：

MN101CF97D(48TQFP)

MN101CFA7D

MN101CP01D

MN101CP28DHT

MN101CP38C

MN101CP39C

MN101CP457

MN101CP49K

MN101CP539HT

MN101CP54C

MN101CP54CBF

MN101CP66D