P14RG-2415E41LF [PEAK]

PMBW-SERIES;


型号：	P14RG-2415E41LF
厂家：	PEAK ELECTRONICS GMBH
描述：	PMBW-SERIES
文件：	总4页 (文件大小：154K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

P14RG-xxxxE/Z4:1LF

Mainzer Straße 151–153

D-55299 Nackenheim

Tel. +49 6135 7026-0

Fax: +49 6135 931070

www.peak-electronics.de

peak@peak-electronics.de

PMBW-SERIES

ꢀ 3 Watt

ꢀ 4:1 Ultra Wide Input

ꢀ Reg. Single and Dual Output

ꢀ 1.5 kV DC I/O Isolation

ꢀ SIP9 case

Rev.04-2009

The PMBW 3Watt series is a family of cost effective DCDC converters with

4:1 ultra wide input, 3W single and dual output DC/DC converters with

control Pin. These converters are encapsulated in an ultra miniature SIP9

plastic case. High performance features: continuous / long time short circuit

protection with automatic restart and tight line / load regulation, high

efficiency operation and output voltage accuracy of ±2% maximum.

ꢀ On/Off Control

ꢀ Contin. Short Circuit Protection

All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified

Input Specifications

Voltage Range

Input Filter

Input Reflected Ripple Current¹

Start-up Time

4:1 Ultra Wide Input (see table)

Capacitor

20 mA pk-pk

10 mS, typ.

Output Specifications

Voltage Accuracy

Short Circuit Protection

Line Regulation

Indefinite (hiccup, Automatic Recovery)

0.5%

Load Regulation (0% - 100%)

Cross Regulation (Dual Output)

Ripple and Noise (20Mhz bandwidth)

Temperature Coefficient

Transient Recovery Time³

Transient Response Deviation³

0.5%, max.(<10% load: 1% for 3.3Vout and 5Vout)

50 mV pk-pk

0.02% / °C

300 us, typ.

3%, max.

General Specifications

I/O Isolation Voltage (3 sec.)

I/O Isolation Capacity

I/O Isolation Resistance

Switching Frequency

Humidity

1500 VDC

500 pF, max.

1000 M Ohm

250 kHz

95% rel H

> 1.212 Mhrs

Reliability Calculated MTBF (MIL-HDBK-217F)

Physical Specifications

Case Material

Potting Material

Weight

Non Conductive Black Plastic (UL94V-0 rated)

Epoxy (UL94V-0 rated)

~ 6.5 g, typ.

Environment Specifications

Operating Temperature

Maximum Case Temperature

Storage Temperature

Cooling

-40 to +75°C (ambient)

100°C

-40 to +125°C

Free Air Convection (10mm distance required)

Soldering 260°C, max. (1.5mm from case 10s.)

RoHS Conform

PMBW-Series – P14RG-xxxxE/Z4:1LF – Single / Dual Output – SIP9 - Plastic Case

Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.

Page 1/4

Selection Guide

Single/Dual Output

Order #

SINGLE OUTPUT

P14RG-243R3E4:1LF

P14RG-2405E4:1LF

P14RG-2412E4:1LF

P14RG-2415E4:1LF

P14RG-483R3E4:1LF

P14RG-4805E4:1LF

P14RG-4812E4:1LF

P14RG-4815E4:1LF

9-36

125

153

149

148

3.3

700

600

250

200

700

600

250

200

2200

1000

165

9-36

3.3

9-36

100

18-72

2200

1000

165

100

Order #

DUAL OUTPUT

P14RG-2405Z4:1LF

P14RG-2412Z4:1LF

P14RG-2415Z4:1LF

P14RG-4805Z4:1LF

P14RG-4812Z4:1LF

P14RG-4815Z4:1LF

9-36

155

149

300

125

100

300

125

100

470

100

9-36

18-72

470

100

If you need other specifications, please enquire.

PMBW-Series – P14RG-xxxxE/Z4:1LF – Single / Dual Output – SIP9 - Plastic Case

Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.

Page 2/4

Package / Pinning / Derating

PIN CONNECTIONS

SINGLE DUAL

1 - Vin

- Vin

+Vin

2 +Vin

3 Ctrl.

Ctrl.

6 +Vout

7 N.C.

8 N.C.

9 - Vout

+Vout

Common

N.C.

- Vout

App Notes:

¹= Measured Input reflected ripple current with a simulated source inductance of 12uH

²= Tested by nominal Vin and constant resistive load.

³= Test by normal Vin and 100%-25% load,25% Ioad step change; If Vout is 3.3V then the Transient Response Deviation is ±5%.

⁴= Input filter components are required to help meet conducted emission class A

⁵= An external filter capacitor is required to meet EN61000-4-4 and EN61000-4-5. (e.g. Nippon-chemi-con KY series, 220uF/100V)

EMC SPECIFICATIONS

Remote ON/OFF

Conducted

EN 55022

CLASS A

Emissions⁴

Radiated

Emissions

ESD

The MCU Pin Voltage is referenced to –Vin (Pin1)

ON: 0 – 0.6 VDC or open circuit

OFF: 2.7 - 15 VDC

EN 55022

CLASS A

IEC 61000-4-2

IEC 61000-4-3

IEC 61000-4-4

IEC 61000-4-5

IEC 61000-4-6

IEC 61000-4-8

Perf. Criteria B

Perf. Criteria A

Perf. Criteria B

Perf. Criteria A

OFF stand by input current: 5mA, max.

EFT⁵

Surge⁵

PFMF

PMBW-Series – P14RG-xxxxE/Z4:1LF – Single / Dual Output – SIP9 - Plastic Case

Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.

Page 3/4

App Notes

Test Configurations

Input Reflected Ripple Current

Test Step

Input reflected ripple current is measured

through a source inductor Lin(12uH) and a

source capacitor Cin(47uF, ESR<1.Ohm at

100KHz) at nominal input and full load.

Output Ripple & Noise

Measurement Test

The Scope measurement bandwidth is

20MHz.

EMI Filter

Input filter components (C1, L) are used to

help meet conducted emissions

equirement for the module. These

components should be mounted as close

as possible to the module; and all leads

should be minimized to decrease radiated

noise.

Input Components

P14RG-24xx

P14RG-48xx

1210, 225k/100V,X7R (2pcs)

1210,105k/100V,X7R

6.8 uH

56 uH

PMBW-Series – P14RG-xxxxE/Z4:1LF – Single / Dual Output – SIP9 - Plastic Case

Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.

Page 4/4

相关型号：