PI6C10806 [PERICOM]
1.8V/2.5V, 250MHz, Low Skew 1:6 Crystal to LVCMOS Clock Buffer; 1.8V / 2.5V , 250MHz的,低偏移1 : 6到水晶LVCMOS时钟缓冲器型号: | PI6C10806 |
厂家: | PERICOM SEMICONDUCTOR CORPORATION |
描述: | 1.8V/2.5V, 250MHz, Low Skew 1:6 Crystal to LVCMOS Clock Buffer |
文件: | 总7页 (文件大小:439K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PI6C10806
1.8V/2.5V, 250MHz, Low Skew 1:6 Crystal to LVCMOS Clock Buffer
Features
Description
• Six low skew outputs: < 80ps
Pericom Semiconductor’s PI6C10806 is a low skew six output
crystal oscillator driver. Crystal oscillator input range is from
10MHz to 40MHz. If XTAL_IN is driven with a signal source,
then the input frequency can be as high as 250MHz. PI6C10806,
the outputs are configured into 2 groups: a five output and a single
output; each with independent output enable.
• Crystal oscillator input: 10MHz to 40MHz
• Switching frequency up to 250 MHz
• Fast output rise/fall time: < 800ps
• Synchronous output enables
• Industrial Temperature range: –40°C to +85°C
• 1.8V and 2.5V operation
PI6C10806 has a wide range of operating voltages: 1.8V and 2.5V.
This feature paired with the low output-to-output and part-to-part
skew makes the device ideal for low voltage, low power, high
frequency single ended applications; such as networking
• Packaging (Pb-free & Green available):
– 16-pin 173-mil wide TSSOP (L)
Block Diagram
Pin Configuration
XTAL_OUT
ENABLE2
GND
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
XTAL_IN
ENABLE1
BCLK5
5
XTAL_IN
BCLK[0:4]
BCLK5
XTAL_OUT
V
BCLK0
DDO
ENABLE1
Sync
Sync
BCLK4
GND
V
DDO
BCLK1
GND
BCLK3
ENABLE2
BCLK2
V
DD
(1)
Pin Description
Truth Table
Pin Name
Description
Inputs
Outputs
BCLK[0:4]
ENABLE1
ENABLE2
BCLK5
L
ENABLE1,
ENABLE2
Active High Output Enable Inputs
L
L
L
H
L
L
XTAL_IN
XTAL_OUT
BCLK[0:5]
GND
Crystal interface
Crystal interface
Clock Outputs
Ground
L
Switching
L
H
H
Switching
Switching
H
Switching
Note:
1.
H = High Voltage Level, L = Low Voltage Level
V
DD
Core Power
V
Output Power
DDO
PS8823B
04/27/07
07-0112
1
PI6C10806
1.8V/2.5V Low Skew 1:6 Crystal to LVCMOS Clock Buffer
2.5V Absolute Maximum Ratings (Above which the useful life may be impaired. For user guidelines only, not tested.)
Note:
Storage Temperature...........................................................–65°C to +150°C
Voltage...............................................................–0.5V to +3.6V
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional operation
of the device at these or any other conditions above those
indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect reliability.
V
V
DD, DDO
Output Voltage (max. 3.6V) .......................................... –0.5V to V +0.5V
DD
Input Voltage (max 3.6V).............................................. –0.5V to V +0.5V
DD
2.5V I/O DC Characteristics (Over Operating Range: V = 2.5V ± 5%, T = -40° to 85°C)
DD
A
(1)
(2)
Parameters
Description
I/O Supply Voltage
Input HIGH Voltage
Input LOW Voltage
Test Conditions
Min.
2.375
1.7
-0.3
2
Typ.
Max.
Units
V
DDO
2.5
2.625
V
IH
Logic HIGH level
Logic LOW level
V
+0.3
DD
V
V
0.7
IL
I
OH
I
OH
I
OL
I
OL
= -1mA
= -8mA
= 1mA
= 8mA
V
Output High Voltage
Output LOW Voltage
V
V
= Min., V = V or V
IN IH IL
OH
DDO
2
V
0.4
0.4
V
OL
= Min., V = V or V
IN IH IL
DDO
Notes:
1. For Max. or Min. conditions, use appropriate operating range values.
2. Typical values are at VCC = 2.5V, +25°C ambient and maximum loading.
2.5V I/O AC Characteristics (Over Operating Range: V /V
= 2.5V ± 5%, T = -40° to 85°C)
DD DDO
A
(1)
Parameters
Description
Test Conditions
Min.
10
Typ
Max.
40
Units
Using Crystal
f
Output Frequency
MHz
OUT
(2)
External Clock
@ V /2
0
`
250
53
t
DC
Output Duty Cycle
47
%
ps
DDO
t /t
R F
CLKn Rise/Fall Time
20% to 80%
150
800
Output to Output Skew between any two
outputs of the same device @ same transition
(3)
t
@V
/2
/2
60
4
ps
SK(O)
DDO
DDO
( 4)
DIS, EN
t
t
Output Enable/Disable
@V
cycles
Notes:
1. Unless noted otherwise, all parameters are tested with xtal @ f <= Fxtal_max,; outputs are terminated @ 50Ω to V
2. External clock source is driving XTAL_IN input
/2, see waveforms.
DDO
3. Identical conditions: loading, transitions, supply voltage, temperature, package type and speed grade.
4. These parameters are guaranteed, but not tested.
Min & Max delay is 4 cycles.
PS8823B
04/27/07
07-0112
2
PI6C10806
1.8V/2.5V Low Skew 1:6 Crystal to LVCMOS Clock Buffer
1.8V Absolute Maximum Ratings (Above which the useful life may be impaired. For user guidelines only, not tested.)
Note:
Storage Temperature...........................................................–65°C to +150°C
,V Voltage................................................................–0.5V to +2.5V
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional operation
of the device at these or any other conditions above those
indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect reliability.
V
DDO DD
Output Voltage (max 2.5V) .......................................... –0.5V to V +0.5V
DD
Input Voltage (max 2.5V) ............................................. –0.5V to V +0.5V
DD
1.8V I/O DC Characteristics (Over Operating Range: T = -40° to 85°C)
A
(1)
(2)
Parameters Description
Test Conditions
Min.
2.375
1.6
Typ.
2.5
Max.
2.625
2.0
Units
2.5V Core Supply
V
DD
1.8V Core Supply
I/O Supply Voltage
Input HIGH Voltage
Input LOW Voltage
Input Current
1.8
V
1.6
1.8
2.0
V
DDO
V
Logic HIGH level
Logic LOW level
0.65*V
-0.3
V
+0.3
DD
IH
DD
V
0.35*Vdd
15
IL
L
I
V
DD
= Max, V = V or GND I pin
μA
IN
DD
I
OH
I
OH
I
OL
I
OL
= -2mA
= -8mA
= 2mA
= 8mA
1.2
1.2
V
Output High Voltage
Output Low Voltage
V
= Min., V = V or V
IN IH IL
OH
DD
V
0.35
0.35
V
V
= Min., V = V or V
OL
DD IN IH IL
Notes:
1. For Max. or Min. conditions, use appropriate operating Vdd and Ta values.
2. Typical values are at VCC = 1.8V, +25°C ambient and maximum loading.
1.8V I/O AC Characteristics (Over Operating Range: V
= 1.8V ± 0.2V, T = -40° to 85°C)
DDO
A
(1)
Parameters
Description
Test Conditions
Min.
2.375
1.6
Typ
2.5
Max.
2.625
2.0
Units
2.5V Core Supply
V
V
DD
1.8V Core Supply
Output Frequency
1.8
Using Crystal
10
40
f
MHz
OUT
(2)
External Clock
@ V /2
0
180
53
t
Output Duty Cycle
47
%
ps
DC
DDO
t /t
R F
CLKn Rise/Fall Time
20% to 80%
150
800
Output to Output Skew between any two
outputs of the same device @ same transition
(3)
t
@V
/2
60
4
ps
SK(O)
DDO
( 4)
DIS, EN
t
t
Output Enable/Disable
@V
/2
cycles
DDO\
Notes:
1. Unless noted otherwise, all parameters are tested with xtal @ f <= Fxtal_max,; outputs are terminated @ 50Ω to V
2. External clock source is driving XTAL_IN input
/2, see waveforms.
DDO
3. Identical conditions: loading, transitions, supply voltage, temperature, package type and speed grade.
4. These parameters are guaranteed, but not tested.
Min & Max delay is 4 cycles.
PS8823B
04/27/07
07-0112
3
PI6C10806
1.8V/2.5V Low Skew 1:6 Crystal to LVCMOS Clock Buffer
Phase Noise and Jitter
(Over Operating Range: V = V
= 1.8V ± 0.2V, and V = V
= 2.5V ± 5%, T = -40° to 85°C)
DDO A
DD
DDO
DD
(1)
Symbol
Description
Test Conditions
Min.
Typ
Max.
2.5
Units
ps
25MHz @ Integration Range
1MHz ~ 20MHz
t
JIT
Random RMS Phase Jitter
Phase Noise Power
PN
Offset Range 1MHz ~ 20MHz
-125
dBc/Hz
Waveforms
Output to Output Skew – tSK(O)
Duty Cycle – tDC
tPW
VOH
VDDO
BCLKx
VDDO/2
VOL
VDDO/2
0V
tPERIOD
tDC = (tPW / tPERIOD ) x 100%
tSK(O)
tSK(O)
tPZL
VOH
BCLKy
VDDO/2
VOL
ENABLE1, ENABLE2 Timing Diagram
BCLK5
BCLK[0:4]
ENABLE2
ENABLE1
AC Test Circuit Load
[VDD - VDDO/2]
[+VDDO/2]
VDD
Scope
VDDO
Z = 50-Ohm
GND
50-
Ohm
Note:
/V
V
= 1.8V ± 0.2V,
DD DDO
[-VDDO/2]
2.5V ± 5%
PS8823B
04/27/07
07-0112
4
PI6C10806
1.8V/2.5V Low Skew 1:6 Crystal to LVCMOS Clock Buffer
Crystal Characteristic (link to "http://www.pericom.com/saronix" for more detailed crystal specifications)
Parameters
OSCMODE
FREQ
Description
Min
Typ
Fundamental
25
Max.
Units
Mode of Oscillation
Frequency
10
30
16
40
200
32
MHz
Ohm
pF
(1)
ESR
Equivalent Series Resistance
Load Capacitance
CLOAD
CSHUNT
Shunt Capacitance
7
pF
Operating Drive Level
Correlation Drive Level
0.5
0.1
mW
mW
DRIVE
Note: 1. ESR value is dependent upon frequency of oscillation
Application Notes
Crystal circuit connection
The following diagram shows PI6C10806 crystal circuit connection with a parallel crystal. For the C =18pF
L
crystal, it is suggested to use C1=18pF, C2=18pF. C1 and C2 can be adjusted to fine tune to the target ppm of
crystal oscillator according to different board layouts. R1=100Ω is strongly suggested.
Crystal Oscillator Circuit
XTAL_IN
C1
18pF
Crystalꢀ(CLꢀ=ꢀ18pF)
100Ω
XTAL_OUT
R1
C2
18pF
PS8823B
04/27/07
07-0112
5
PI6C10806
1.8V/2.5V Low Skew 1:6 Crystal to LVCMOS Clock Buffer
Package Mechanical - 16-lead TSSOP (L)
16
.169
.177
4.3
4.5
1
0.09
0.20
.193
.201
.004
.008
4.9
5.1
.047
max.
1.20
0.45 .018
0.75 .030
SEATING
PLANE
.252
BSC
6.4
.002
.006
0.05
0.15
.0256
BSC
.007
.012
0.65
0.19
0.30
(1,2,3)
PI6C10806 Ordering Information
Ordering Code
Package Code
Package Description
PI6C10806LE
L
Pb-Free and Green 16-pin 173-mil TSSOP
Notes:
1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
2. E = Pb-free and Green
3. X suffix = Tape/Reel
PS8823B
04/27/07
07-0112
6
PI6C10806
1.8V/2.5V Low Skew 1:6 Crystal to LVCMOS Clock Buffer
Packaging Information: HC-49
Package Marking Information
Line 1:
S = SaRonix
xxx = Calib/Stability/Temp Code
YYWWX = Date Code
Line 2:
Frequency (up to 7 digits, including decimal point)
BT-cut = B or
AT-cut Parallel = –(dash) or
AT-cut Series = leave Blank
xx = Load Capacitance (leave Blank if Series)
Land Pattern
Land Pattern
SxxxYYWWX
25.0000-xx
Pericom/Saronix Miniature Low Profile SMD Quartz Crystal Ordering Information
49xxx XXX
–
XX XXX
X (X)
Type / Package
Options
49SMLB = 2 contact, 4mm high
49SAB = 4 contact, 5 mm high
49SNC = 4 contact, 5mm high
49SUB = 6 contact, 5mm high
(T) = Tape and Reel (full increments only) 1000 pieces
Blank = Bulk
–E (dash E) = Lead (Pb)-free RoHS Compliant Version
Blank = Standard version
Frequency
Frequency (in MHz) = 0x.xxxx, xx.xxxx
(a zero is used in front of frequencies under 10 MHz)
Calibration / Stability / Temp Range
GGC = ±30ppm / ±30ppm / -20 to +70°C
GHE = ±30ppm / ±50ppm / -40 to +85°C
HJE = ±50ppm / ±100ppm / -40 to +85°C
*others available
B = BT-cut, 26.8 to 50 MHz
– (dash) = AT-cut Parallel Resonance
Blank = AT-cut Series Resonance
Pad Connection Configurations
Load Capacitance
xx = Parallel Resonance (specify load)
Blank = Series Resonance
Examples:
25.0000MHz, ±30ppm calib, ±30ppm stability, -20 to +70°C (Commercial), 16pF
49SMLB25.0000-16GGC
49SMLB25.0000-16GGC–E (for lead-free)
25.0000MHz, ±30ppm calib, ±30ppm stability, -40 to +85°C (Industrial), 16pF
49SMLB25.0000-16GHE
49SMLB25.0000-16GHE–E (for lead-free)
Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com
PS8823B
04/27/07
07-0112
7
相关型号:
PI6C10806ALE
Low Skew Clock Driver, 6C Series, 6 True Output(s), 0 Inverted Output(s), CMOS, PDSO16, 0.173 INCH, GREEN, MO-153F/AB, TSSOP-16
PERICOM
PI6C10806ALEX
Low Skew Clock Driver, 6C Series, 6 True Output(s), 0 Inverted Output(s), CMOS, PDSO16, 0.173 INCH, GREEN, MO-153F/AB, TSSOP-16
PERICOM
PI6C10807HE
Low Skew Clock Driver, 6C Series, 10 True Output(s), 0 Inverted Output(s), PDSO20, 0.209 INCH, GREEN, MS-150B/AE, SSOP-20
PERICOM
PI6C10807LE
Low Skew Clock Driver, 6C Series, 10 True Output(s), 0 Inverted Output(s), PDSO20, 0.173 INCH, GREEN, MO-153F/AC, TSSOP-20
PERICOM
PI6C10807LEX
Low Skew Clock Driver, 6C Series, 10 True Output(s), 0 Inverted Output(s), PDSO20, 0.173 INCH, GREEN, MO-153F/AC, TSSOP-20
PERICOM
PI6C10810HE
Clock Driver, 6C Series, 10 True Output(s), 0 Inverted Output(s), PDSO20, 0.209 INCH, GREEN, MS-150B/AE, SSOP-20
DIODES
©2020 ICPDF网 联系我们和版权申明