PI74FCT151TWX [PERICOM]
暂无描述;型号: | PI74FCT151TWX |
厂家: | PERICOM SEMICONDUCTOR CORPORATION |
描述: | 暂无描述 复用器 |
文件: | 总5页 (文件大小:55K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PI74FCT151T
PI74FCT251T
(25Ω Series) PI74FCT2151T
Fast CMOS 8-Input Multiplexer
ProductFeatures:
Product Description:
• PI74FCT151/251/2151TispincompatiblewithbipolarFAST™
Pericom Semiconductor’s PI74FCT series of logic circuits are pro-
duced in the Company’s advanced 0.8 micron CMOS technology,
achieving industry leading speed grades.
Series at a higher speed and lower power consumption
• 25Ω seriesresistoronalloutputs(FCT2xxxOnly)
• TTL input and output levels
• Extremelylowstaticpower
• Hysteresis on all inputs
The PI74FCT151T, PI74FCT251T, and PI74FCT2151T are high-
speed 8-input multiplexers. They select one bit from a source of
eight under the control of three select inputs. Both assertion and
negation outputs are provided.
• Industrial operating temperature range: –40°C to +85°C
• Packagesavailable:
The PI74FCT151/2151T has a common, active-LOW, Enable
input (E). When E is LOW, data from one of eight inputs is directed
to the complementary outputs based on the 3-bit code applied to the
Select (S0-S2) inputs. The PI74FCT151/2151T can be used as a
data routing device from one of eight sources.
– 16-pin150-milwideplasticQSOP(Q)
– 16-pin300-milwideplasticSOIC(S)
– 16-pin150-milwideplasticSOIC(W)
The PI74FCT251T has a common Active-LOW Output Enable
(OE) input. When OE is LOW, data from one of eight inputs is
directed to the complementary outputs. When OE is HIGH, both
outputsareswitchedtoahigh-impedancestateallowingmultiplexer
expansion by tying several outputs together.
Logic Block Diagram
I
I
I
I
I
I
I
I
7
6
5
4
3
2
1
0
Z
Z
FCT251 Only
S
2
S
1
S
0
E for 151
OE for 251
PS2028A 03/11/96
1
PI74FCT151/2151/251T
8-INPUT MULTIPLEXER
Truth Table(1)
Product Pin Description
Inputs
Outputs
Pin Name
I0-I7
S0-S2
E
Description
S2
X
X
L
S1
X
X
L
S0
E/OE(2)
Z
L(3)
Z(4)
I0
Z
H(3)
Z(4)
I0
Data Inputs
X
X
L
H
H
L
L
L
L
L
L
L
L
Select Inputs
Enable Input (Active LOW) FCT151/2151T
OE
Output Enable (Active LOW) FCT251T
L
L
H
L
I1
I1
Z
Data Output
Inverted Data Output
Ground
L
H
H
L
I2
I2
Z
L
H
L
I3
I3
GND
VCC
H
H
H
H
I4
I4
Power
L
H
L
I5
I5
H
H
I6
I6
H
I7
I7
PI74FCT151/2151T Product Pin Configuration
Notes:
1. E for 151/2151, OE for 251.
2. H = High Voltage Level
L = Low Voltage Level
X = Don’t Care
Z = High Impedance
3. 151/2151 ONLY.
4. 251 ONLY.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
I
I
I
I
3
2
1
0
VCC
I
I
I
I
4
5
6
7
16-PIN
Q16
S16
Z
Z
W16
S0
S1
S2
* E or OE
GND
* E for 151/2151 only, OE for 251 only
PS2028A 03/11/96
2
PI74FCT151/2151/251T
8-INPUT MULTIPLEXER
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
StorageTemperature .................................................................... –65°Cto+150°C
Ambient Temperature with Power Applied .....................................-40°Cto+85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .............. –0.5Vto+7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) ........... –0.5Vto+7.0V
DC Input Voltage ............................................................................ –0.5Vto+7.0V
DC Output Current ..................................................................................... 120mA
Power Dissipation ..........................................................................................0.5W
Note:
Stresses greater than those listed under
MAXIMUM RATINGS may cause permanent
damage to the device. This is a stress rating
only and functional operation of the device at
these or any other conditions above those
indicated in the operational sections of this
specification is not implied. Exposure to
absolute maximum rating conditions for
extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ± 5%)
Parameters Description
TestConditions(1) Min. Typ(2) Max. Units
Output HIGH Voltage VCC = Min., VIN = VIH or VIL
VOH
VOL
VOL
IOH = –15.0 mA
IOL = 48 mA
2.4
3.0
0.3
0.3
V
V
V
Output LOW Current
Output LOW Current
VCC = Min., VIN = VIH or VIL
0.50
0.50
VCC = Min., VIN = VIH or VIL
IOL = 12 mA
(25Ω series)
VIH
VIL
IIH
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
VCC = Max.
2.0
V
V
0.8
1
VIN =VCC
µA
µA
IIL
VCC = Max.
VIN =GND
–1
IOZH
IOZL
High Impedance
Output Current
VCC = Max.
VOUT =2.7V
VOUT =0.5V
1
µA
µA
–1
VIK
IOS
Clamp Diode Voltage VCC = Min., IIN = –18 mA
–0.7
–120
—
–1.2
100
V
Short Circuit Current
Power Down Disable
Input Hysteresis
VCC =Max.(3),VOUT =GND
–60
—
mA
µA
mV
IOFF
VH
VCC =GND,VOUT =4.5V
200
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(4)
Description
Test Conditions
VIN = 0V
Typ
Max.
Units
pF
CIN
Input Capacitance
Output Capacitance
6
8
10
12
COUT
VOUT = 0V
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. This parameter is determined by device characterization but is not production tested.
PS2028A 03/11/96
3
PI74FCT151/2151/251T
8-INPUT MULTIPLEXER
Power Supply Characteristics
Parameters Description
Test Conditions(1)
Min. Typ(2) Max. Units
ICC
Quiescent Power
Supply Current
VCC = Max.
VIN = GND or VCC
0.1
500
µA
∆ICC
ICCD
Supply Current per
Input @ TTL HIGH
VCC = Max.
VIN = 3.4V(3)
0.5
2.0
mA
Supply Current per
Input per MHz(4)
VCC = Max.,
Outputs Open
VIN = VCC
VIN = GND
0.15
0.25
mA/
MHz
E or OE = GND
One Bit Toggling
50% Duty Cycle
IC
Total Power Supply
Current(6)
VCC = Max.,
Outputs Open
fI = 10 MHZ
50% Duty Cycle
E or OE = GND
One Bit Toggling
VIN = VCC
VIN = GND
3.2
3.5
6.5(5)
7.5(5)
mA
VIN = 3.4V
VIN = GND
Notes:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V); all other inputs at Vcc or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested.
6. IC =IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ∆ICC DHNT + ICCD (fCP/2 + fINI)
ICC = Quiescent Current
∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
fI = Input Frequency
NI = Number of Inputs at fI
All currents are in milliamps and all frequencies are in megahertz.
PS2028A 03/11/96
4
PI74FCT151/2151/251T
8-INPUT MULTIPLEXER
PI74FCT151/2151T Switching Characteristics over Operating Range
151T/2151T
Com.
151AT/2151AT
Com.
151CT/2151CT
Com.
Parameters
Description
Conditions(1)
Min
1.5
Max
9.0
Min
Max
Min
Max
Unit
t
t
t
t
t
t
t
t
t
t
t
t
PLH
PHL
PLH
PHL
PLH
PHL
PLH
PHL
PLH
PHL
PLH
PHL
PropagationDelay
Sn to Z
C
R
L
L
= 50 pF
1.5
6.6
1.5
5.6
ns
= 500
Ω
PropagationDelay
Sn to Z
1.5
1.5
1.5
1.5
1.5
10.5
7.0
9.5
6.5
7.5
1.5
1.5
1.5
1.5
1.5
6.8
5.6
5.8
5.2
5.5
1.5
1.5
1.5
1.5
1.5
5.8
4.8
5.0
4.4
4.7
ns
ns
ns
ns
ns
PropagationDelay
E to Z
PropagationDelay
E to Z
PropagationDelay
In to Z
PropagationDelay
In to Z
PI74FCT251T Switching Characteristics over Operating Range
251T
Com.
251AT
Com.
251CT
Com.
Parameters
Description
Conditions(1)
Min
Max
Min
Max
Min
Max
Unit
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
PLH
PHL
PLH
PHL
PLH
PHL
PLH
PHL
PZH
PZL
PHZ
PLZ
PZH
PZL
PHZ
PLZ
PropagationDelay
Sn to Z
C
R
L
L
= 50 pF
1.5
9.0
1.5
6.6
1.5
5.6
ns
= 500
Ω
PropagationDelay
Sn to Z
1.5
1.5
1.5
1.5
1.5
1.5
1.5
11.0
7.0
7.0
9.0
7.5
9.0
7.0
1.5
1.5
1.5
1.5
1.5
1.5
1.5
6.8
5.2
5.5
6.7
6.0
6.7
6.0
1.5
1.5
1.5
1.5
1.5
1.5
1.5
5.8
4.4
4.7
5.7
5.0
5.7
5.0
ns
ns
ns
ns
ns
ns
ns
PropagationDelay
In to Z
PropagationDelay
In to Z
Output Enable Time
OE to Z
Output Disable Time(3)
OE to Z
Output Enable Time
OE to Z
Output Disable Time(3)
OE to Z
Notes:
1. See test circuit and wave forms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. This parameter is guaranteed but not production tested.
Pericom Semiconductor Corporation
2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com
PS2028A 03/11/96
5
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明