PI74FCT153CTQX [PERICOM]
Multiplexer, FCT Series, 2-Func, 4 Line Input, 1 Line Output, True Output, CMOS, PDSO16, 0.150 INCH, PLASTIC, QSOP-16;型号: | PI74FCT153CTQX |
厂家: | PERICOM SEMICONDUCTOR CORPORATION |
描述: | Multiplexer, FCT Series, 2-Func, 4 Line Input, 1 Line Output, True Output, CMOS, PDSO16, 0.150 INCH, PLASTIC, QSOP-16 复用器 |
文件: | 总5页 (文件大小:51K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PI74FCT153T/253T
(25Ω Series) PI74FCT2153T/2253T
High-Speed CMOS Dual 4-Input Multiplexer
ProductFeatures:
Product Description:
• PI74FCT153T/253T/2153T/2253Tispincompatiblewith
bipolar FAST™ Series at a higher speed and lower power
consumption
• 25Ω series resistor on all outputs ( FCT2XXX only)
• TTL input and output levels
• Low ground bounce outputs (25Ω series only)
• Extremelylowstaticpower
• Hysteresis on all inputs
Pericom Semiconductor’s PI74FCT series of logic circuits are pro-
duced in the Company’s advanced 0.8 micron CMOS technology,
achievingindustryleadingspeedgrades.AllPI74FCT2XXXdevices
have a built-in 25-ohm series resistor on all outputs to reduce noise
resulting from reflections, thus eliminating the need for an external
terminating resistor.
The PI74FCT153T/253T and PI74FCT2153T/2253T are high-
speed dual 4-input multiplexers. The PI74FCT153T/2153T has
TTL outputs, while the PI74FCT253T/2253T has 3-state outputs.
The output buffers are designed with a power-off disable allowing
“live insertion” of boards when used as backplane drivers.
• Industrial operating temperature range: –40°C to +85°C
• Packagesavailable:
– 16-pin150milwideplasticQSOP(Q)
– 16-pin300milwideplasticSOIC(S)
– 16-pin150milwideplasticSOIC(W)
Logic Block Diagram
E
b
E
a
S
1
S
0
I
0a
I
1a
I
2a
I
3a
I
0b
I
1b
I
2b
I3b
3-State Enable
on 253 Only
O
a
Ob
PS2009A 03/09/96
1
PI74FCT153T/253T
(25Ω Series) PI74FCT2153T/2253T
HIGH SPEED CMOS DUAL 4-INPUT MULTIPLEXER
Product Pin Description
Truth Table(1)
Inputs
Outputs
’153/2153 ’253/2253
Pin Name
I0a-I3a, I0b-I3b
S0, S1
Description
Data Inputs
Select Inputs
Enable Input
Data Outputs
Ground
Ea
Eb
S1
X
X
L
S0
X
X
L
Oa
Ob
Oa
Ob
H
X
H
L
L
L
L
L
X
Z
X
Ea, Eb
X
X
L
X
Z
Oa, Ob
L
I0a
I1a
I2a
I3a
I0b
I1b
I2b
I3b
I0a
I1a
I2a
I3a
I0b
I1b
I2b
I3b
GND
L
L
L
H
L
VCC
Power
H
H
L
H
NOTE:
1. H = High Voltage Level
L = Low Voltage Level
X = Don't Care
Z = High Impedance
Product Pin Configuration
1
16
15
14
13
12
11
10
9
Ea
S1
I3a
I2a
I1a
VCC
Eb
S0
I3b
I2b
I1b
I0b
Ob
2
3
16-PIN
Q16
S16
4
5
6
7
8
W16
I0a
Oa
GND
PS2009A 03/09/96
2
PI74FCT153T/253T
(25Ω Series) PI74FCT2153T/2253T
HIGH SPEED CMOS DUAL 4-INPUT MULTIPLEXER
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Note:
Storage Temperature ................................................................. –65°C to +150°C
Ambient Temperature with Power Applied ................................. -40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .......... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) ....... –0.5V to +7.0V
DC Input Voltage ......................................................................... –0.5V to +7.0V
DC Output Current ................................................................................... 120 mA
Power Dissipation......................................................................................... 0.5W
Stresses greater than those listed under
MAXIMUM RATINGS may cause permanent
damage to the device. This is a stress rating
only and functional operation of the device at
these or any other conditions above those
indicated in the operational sections of this
specification is not implied. Exposure to
absolute maximum rating conditions for
extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5.0V ± 5%)
Parameters Description
TestConditions(1) Min. Typ(2) Max. Units
VOH
VOL
VOL
VIH
VIL
IIH
Output HIGH Voltage VCC = Min., VIN = VIH or VIL
Output LOW Current VCC = Min., VIN = VIH or VIL
Output LOW Current VCC = Min., VIN = VIH or VIL
IOH = –15.0 mA
2.4
3.0
V
V
IOL = 48 mA
0.3 0.50
0.3 0.50
IOL = 12 mA (25Ω Series)
V
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
High Impedance
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
VCC = Max.
2.0
V
0.8
V
VIN =VCC
1
µA
µA
µA
µA
V
IIL
VCC = Max.
VIN =GND
VOUT =2.7V
VOUT =0.5V
–1
IOZH
IOZL
VIK
IOFF
IOS
VCC =MAX.
1
–1
Output Current
Clamp Diode Voltage VCC = Min., IIN = –18 mA
–0.7 –1.2
Power Down Disable VCC =GND,VOUT =4.5V
—
—
100
µA
mA
mV
Short Circuit Current VCC =Max.(3),VOUT =GND
Input Hysteresis
–60 –120
200
VH
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(4)
Description
Test Conditions
VIN = 0V
Typ
6
Max.
10
Units
pF
CIN
Input Capacitance
Output Capacitance
COUT
VOUT = 0V
8
12
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. This parameter is determined by device characterization but is not production tested.
PS2009A 03/09/96
3
PI74FCT153T/253T
(25Ω Series) PI74FCT2153T/2253T
HIGH SPEED CMOS DUAL 4-INPUT MULTIPLEXER
Power Supply Characteristics
Parameters Description
Test Conditions(1)
Min. Typ(2) Max. Units
ICC
Quiescent Power
Supply Current
VCC = Max.
VIN = GND or VCC
0.1
500
µA
∆ICC
ICCD
Supply Current per
Input @ TTL HIGH
VCC = Max.
VIN = 3.4V(3)
0.5
2.0
mA
Supply Current per
Input per MHz(4)
VCC = Max.,
Outputs Open
VIN = VCC
VIN = GND
0.15
0.25
mA/
MHz
Other inputs at GND
One Bit Toggling
50% Duty Cycle
IC
Total Power Supply
Current(6)
VCC = Max.,
Outputs Open
fI = 10 MHZ
50% Duty Cycle
Other inputs at GND
One Bit Toggling
VIN = VCC
VIN = GND
3.2
3.5
6.5(5)
7.5(5)
mA
VIN = 3.4V
VIN = GND
Notes:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V); all other inputs at Vcc or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested.
6. IC =IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ∆ICC DHNT + ICCD (fCP/2 + fINI)
ICC = Quiescent Current
∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
fI = Input Frequency
NI = Number of Inputs at fI
All currents are in milliamps and all frequencies are in megahertz.
PS2009A 03/09/96
4
PI74FCT153T/253T
(25Ω Series) PI74FCT2153T/2253T
HIGH SPEED CMOS DUAL 4-INPUT MULTIPLEXER
PI74FCT153/2153T Switching Characteristics over Operating Range
153T/2153T
Com.
153AT/2153AT
Com.
153CT/2153CT
Com.
Parameters
Description
Conditions(1)
Min
1.5
Max
9.0
Min
Max
Min
Max
Unit
tPLH
tPHL
tPLH
tPHL
tPLH
t
PHL
PropagationDelay
Sn to O
C
L
L
= 50 pF
1.5
6.6
1.5
5.6
ns
R
= 500
Ω
PropagationDelay
In to O
1.5
1.5
7.0
7.0
1.5
1.5
5.2
5.2
1.5
1.5
4.5
4.8
ns
ns
PropagationDelay
E to O
PI74FCT253/2253T Switching Characteristics over Operating Range
253T/2253T
Com.
253AT/2253AT
Com.
253CT/2253CT
Com.
Parameters
Description
Conditions(1)
Min
1.5
Max
9.0
Min
Max
Min
Max
Unit
tPLH
tPHL
tPLH
tPHL
tPZH
tPZL
tPHZ
t
PLZ
PropagationDelay
Sn to O
C
L
L
= 50 pF
1.5
6.6
1.5
5.6
ns
R
= 500
Ω
PropagationDelay
In to O
1.5
1.5
1.5
7.0
9.0
7.0
1.5
1.5
1.5
5.2
6.0
6.0
1.5
1.5
1.5
4.5
5.0
5.0
ns
ns
ns
Output Enable Time
E to O
Output Disable Time(3)
E to O
Notes:
1. See test circuit and wave forms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. This parameter guaranteed but not production tested.
Pericom Semiconductor Corporation
2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com
PS2009A 03/09/96
5
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明