TJA1050T/V,118 [NXP]
TJA1050 - High-speed CAN transceiver SOIC 8-Pin;
| 型号： | TJA1050T/V,118 |
| 厂家： | 
NXP |
| 描述： | TJA1050 - High-speed CAN transceiver SOIC 8-Pin 电信 光电二极管 电信集成电路 |
| 文件： | 总18页 (文件大小：119K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
DATA SHEET
TJA1050
High speed CAN transceiver
Product specification
2003 Oct 22
Supersedes data of 2002 May 16
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
FEATURES
GENERAL DESCRIPTION
• Fully compatible with the “ISO 11898” standard
• High speed (up to 1 Mbaud)
The TJA1050 is the interface between the Controller Area
Network (CAN) protocol controller and the physical bus.
The device provides differential transmit capability to the
bus and differential receive capability to the CAN
controller.
• Very low ElectroMagnetic Emission (EME)
• Differential receiver with wide common-mode range for
high ElectroMagnetic Immunity (EMI)
The TJA1050 is the third Philips high-speed CAN
transceiver after the PCA82C250 and the PCA82C251.
The most important differences are:
• An unpowered node does not disturb the bus lines
• Transmit Data (TXD) dominant time-out function
• Silent mode in which the transmitter is disabled
• Much lower electromagnetic emission due to optimal
matching of the output signals CANH and CANL
• Bus pins protected against transients in an automotive
environment
• Improved behaviour in case of an unpowered node
• No standby mode.
• Input levels compatible with 3.3 V and 5 V devices
• Thermally protected
This makes the TJA1050 eminently suitable for use in
nodes that are in a power-down situation in partially
powered networks.
• Short-circuit proof to battery and to ground
• At least 110 nodes can be connected.
QUICK REFERENCE DATA
SYMBOL
VCC
PARAMETER
supply voltage
CONDITIONS
MIN. MAX. UNIT
4.75
−27
−27
1.5
−
5.25
+40
+40
3
V
VCANH
DC voltage at pin CANH
0 < VCC < 5.25 V; no time limit
0 < VCC < 5.25 V; no time limit
dominant
V
VCANL
DC voltage at pin CANL
V
Vi(dif)(bus)
tPD(TXD-RXD)
Tvj
differential bus input voltage
propagation delay TXD to RXD
virtual junction temperature
V
VS = 0 V; see Fig.7
250
ns
−40
+150 °C
ORDERING INFORMATION
TYPE
PACKAGE
NUMBER
NAME
DESCRIPTION
VERSION
TJA1050T
TJA1050U
SO8
plastic small outline package; 8 leads; body width 3.9 mm
SOT96-1
−
bare die; die dimensions 1700 × 1280 × 380 µm
−
2003 Oct 22
2
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
BLOCK DIAGRAM
V
CC
3
8
S
30 µA
V
CC
GND
TEMPERATURE
PROTECTION
200
µA
TXD
1
DOMINANT
TIME-OUT
TIMER
DRIVER
TXD
RXD
7
V
CC
CANH
CANL
25
kΩ
4
5
0.5V
CC
25
kΩ
RECEIVER
GND
GND
6
REFERENCE
VOLTAGE
TJA1050
V
ref
2
MGS374
GND
Fig.1 Block diagram.
PINNING
SYMBOL
PIN
DESCRIPTION
TXD
1
transmit data input; reads in data
from the CAN controller to the bus
line drivers
handbook, halfpage
GND
VCC
2
3
4
ground
TXD
1
2
3
4
8
S
supply voltage
GND
7
6
5
CANH
CANL
RXD
receive data output; reads out
data from the bus lines to the
CAN controller
TJA1050T
V
CC
V
RXD
ref
Vref
5
6
7
8
reference voltage output
LOW-level CAN bus line
HIGH-level CAN bus line
MGS375
CANL
CANH
S
select input for high-speed mode
or silent mode
Fig.2 Pin configuration.
2003 Oct 22
3
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
FUNCTIONAL DESCRIPTION
Control pin S allows two operating modes to be selected:
high-speed mode or silent mode.
The TJA1050 is the interface between the CAN protocol
controller and the physical bus. It is primarily intended for
high-speed automotive applications using baud rates from
60 kbaud up to 1 Mbaud. It provides differential transmit
capability to the bus and differential receiver capability to
the CAN protocol controller. It is fully compatible to the
“ISO 11898” standard.
The high-speed mode is the normal operating mode and is
selected by connecting pin S to ground. It is the default
mode if pin S is not connected. However, to ensure EMI
performance in applications using only the high-speed
mode, it is recommended that pin S is connected to
ground.
A current-limiting circuit protects the transmitter output
stage from damage caused by accidental short-circuit to
either positive or negative supply voltage, although power
dissipation increases during this fault condition.
In the silent mode, the transmitter is disabled. All other
IC functions continue to operate. The silent mode is
selected by connecting pin S to VCC and can be used to
prevent network communication from being blocked, due
to a CAN controller which is out of control.
A thermal protection circuit protects the IC from damage
by switching off the transmitter if the junction temperature
exceeds a value of approximately 165 °C. Because the
transmitter dissipates most of the power, the power
dissipation and temperature of the IC is reduced. All other
IC functions continue to operate. The transmitter off-state
resets when pin TXD goes HIGH. The thermal protection
A ‘TXD dominant time-out’ timer circuit prevents the bus
lines being driven to a permanent dominant state (blocking
all network communication) if pin TXD is forced
permanently LOW by a hardware and/or software
application failure. The timer is triggered by a negative
edge on pin TXD. If the duration of the LOW-level on
circuit is particularly needed when a bus line short-circuits. pin TXD exceeds the internal timer value, the transmitter is
disabled, driving the bus into a recessive state. The timer
is reset by a positive edge on pin TXD.
The pins CANH and CANL are protected from automotive
electrical transients (according to “ISO 7637”; see Fig.4).
Table 1 Function table of the CAN transceiver; X = don’t care
VCC
TXD
S
CANH
CANL
BUS STATE
RXD
4.75 V to 5.25 V
LOW
LOW (or
floating)
HIGH
LOW
dominant
LOW
4.75 V to 5.25 V
4.75 V to 5.25 V
X
HIGH
X
0.5VCC
0.5VCC
0.5VCC
0.5VCC
recessive
recessive
HIGH
HIGH
HIGH (or
floating)
<2 V (not powered)
2 V < VCC < 4.75 V
X
X
X
0 V < VCANH < VCC 0 V < VCANL < VCC
0 V < VCANH < VCC 0 V < VCANL < VCC
recessive
recessive
X
X
>2 V
2003 Oct 22
4
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are referenced to GND (pin 2).
Positive currents flow into the IC.
SYMBOL
VCC
VCANH
PARAMETER
supply voltage
CONDITIONS
MIN.
−0.3
MAX.
+6
UNIT
V
V
DC voltage at pin CANH
0 < VCC < 5.25 V;
no time limit
−27
+40
VCANL
DC voltage at pin CANL
0 < VCC < 5.25 V;
no time limit
−27
+40
V
VTXD
DC voltage at pin TXD
DC voltage at pin RXD
DC voltage at pin Vref
−0.3
−0.3
−0.3
−0.3
−200
−200
−4000
−200
−55
VCC + 0.3
VCC + 0.3
VCC + 0.3
VCC + 0.3
+200
V
VRXD
Vref
V
V
VS
DC voltage at pin S
V
Vtrt(CANH)
Vtrt(CANL)
Vesd
transient voltage at pin CANH
transient voltage at pin CANL
note 1
note 1
V
+200
V
electrostatic discharge voltage at all pins note 2
+4000
+200
V
note 3
V
Tstg
Tvj
storage temperature
+150
°C
°C
virtual junction temperature
note 4
−40
+150
Notes
1. The waveforms of the applied transients shall be in accordance with “ISO 7637 part 1”, test pulses 1, 2, 3a and 3b
(see Fig.4).
2. Human body model: C = 100 pF and R = 1.5 kΩ.
3. Machine model: C = 200 pF, R = 10 Ω and L = 0.75 µH.
4. In accordance with “IEC 60747-1”. An alternative definition of Tvj is: Tvj = Tamb + P × Rth(vj-a), where Rth(vj-a) is a fixed
value to be used for the calculation of Tvj. The rating for Tvj limits the allowable combinations of power dissipation (P)
and ambient temperature (Tamb).
THERMAL CHARACTERISTICS
According to IEC 60747-1.
SYMBOL
Rth(vj-a)
PARAMETER
CONDITIONS
in free air
VALUE
UNIT
thermal resistance from junction to
ambient in SO8 package
145
K/W
Rth(vj-s)
thermal resistance from junction to
substrate of bare die
in free air
50
K/W
QUALITY SPECIFICATION
Quality specification “SNW-FQ-611 part D” is applicable.
2003 Oct 22
5
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
CHARACTERISTICS
VCC = 4.75 V to 5.25 V; Tvj = −40 °C to +150 °C; RL = 60 Ω unless specified otherwise; all voltages are referenced to
GND (pin 2); positive currents flow into the IC; see notes 1 and 2.
SYMBOL
Supply (pin VCC
ICC
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
)
supply current
dominant; VTXD = 0 V
recessive; VTXD = VCC
25
50
5
75
mA
2.5
10
mA
Transmitter data input (pin TXD)
VIH
VIL
IIH
IIL
HIGH-level input voltage
output recessive
output dominant
VTXD = VCC
2.0
−0.3
−5
−
−
0
VCC + 0.3
+0.8
+5
V
LOW-level input voltage
HIGH-level input current
LOW-level input current
input capacitance
V
µA
µA
pF
VTXD = 0 V
−100
−
−200
−300
10
Ci
not tested
5
Mode select input (pin S)
VIH
VIL
IIH
HIGH-level input voltage
silent mode
high-speed mode
VS = 2 V
2.0
−0.3
20
−
VCC + 0.3
+0.8
50
V
LOW-level input voltage
HIGH-level input current
LOW-level input current
−
V
30
30
µA
µA
IIL
VS = 0.8 V
15
45
Receiver data output (pin RXD)
IOH HIGH-level output current
IOL LOW-level output current
Reference voltage output (pin Vref
Vref reference output voltage
Bus lines (pins CANH and CANL)
VRXD = 0.7VCC
VRXD = 0.45 V
−2
−6
−15
mA
mA
2
8.5
20
)
−50 µA < IVref < +50 µA 0.45VCC
0.5VCC
0.55VCC
V
Vo(reces)(CANH) recessive bus voltage at
pin CANH
VTXD = VCC; no load
VTXD = VCC; no load
2.0
2.0
2.5
2.5
−
3.0
V
Vo(reces)(CANL) recessive bus voltage at
pin CANL
3.0
V
Io(reces)(CANH)
Io(reces)(CANL)
Vo(dom)(CANH)
Vo(dom)(CANL)
Vi(dif)(bus)
recessive output current at
pin CANH
−27 V < VCANH < +32 V; −2.0
0 V < VCC < 5.25 V
+2.5
+2.5
4.25
1.75
3.0
mA
mA
V
recessive output current at
pin CANL
−27 V < VCANL < +32 V; −2.0
0 V < VCC < 5.25 V
−
dominant output voltage at
pin CANH
VTXD = 0 V
VTXD = 0 V
3.0
0.5
1.5
3.6
1.4
2.25
0
dominant output voltage at
pin CANL
V
differential bus input voltage VTXD = 0 V; dominant;
(VCANH − VCANL 42.5 Ω < RL < 60 Ω
TXD = VCC; recessive; −50
no load
V
)
V
+50
mV
2003 Oct 22
6
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
−70
MAX.
−95
UNIT
mA
Io(sc)(CANH)
short-circuit output current at VCANH = 0 V; VTXD = 0 V −45
pin CANH
Io(sc)(CANL)
Vi(dif)(th)
short-circuit output current at VCANL = 36 V;
pin CANL TXD = 0 V
differential receiver threshold −12 V < VCANL < +12 V; 0.5
45
70
100
0.9
mA
V
V
0.7
voltage
−12 V < VCANH < +12 V;
see Fig.5
Vi(dif)(hys)
differential receiver input
voltage hysteresis
−12 V < VCANL < +12 V; 50
−12 V < VCANH < +12 V;
see Fig.5
70
100
mV
Ri(cm)(CANH)
Ri(cm)(CANL)
Ri(cm)(m)
common mode input
resistance at pin CANH
15
25
25
0
35
35
+3
kΩ
kΩ
%
common mode input
resistance at pin CANL
15
matching between
pin CANH and pin CANL
common mode input
resistance
VCANH = VCANL
−3
Ri(dif)
differential input resistance
25
50
75
20
kΩ
Ci(CANH)
input capacitance at
pin CANH
VTXD = VCC; not tested
VTXD = VCC; not tested
−
7.5
pF
Ci(CANL)
input capacitance at
pin CANL
−
7.5
20
pF
Ci(dif)
differential input capacitance VTXD = VCC; not tested
−
3.75
170
10
pF
ILI(CANH)
input leakage current at
pin CANH
VCC = 0 V; VCANH = 5 V 100
250
µA
ILI(CANL)
input leakage current at
pin CANL
VCC = 0 V; VCANL = 5 V 100
170
250
180
µA
°C
Thermal shutdown
Tj(sd) shutdown junction
temperature
Timing characteristics (see Figs.6 and 7)
155
165
td(TXD-BUSon)
td(TXD-BUSoff)
td(BUSon-RXD)
td(BUSoff-RXD)
tdom(TXD)
delay TXD to bus active
delay TXD to bus inactive
delay bus active to RXD
delay bus inactive to RXD
VS = 0 V
VS = 0 V
VS = 0 V
VS = 0 V
VTXD = 0 V
25
25
20
45
250
55
60
50
95
450
110
95
ns
ns
ns
ns
µs
110
155
750
TXD dominant time for
time-out
Notes
1. All parameters are guaranteed over the virtual junction temperature range by design, but only 100 % tested at 125 °C
ambient temperature for dies on wafer level and in addition to this 100 % tested at 25 °C ambient temperature for
cased products, unless specified otherwise.
2. For bare die, all parameters are only guaranteed if the backside of the bare die is connected to ground.
2003 Oct 22
7
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
APPLICATION AND TEST INFORMATION
47 nF
+
5 V
100
nF
60 Ω
60 Ω
V
CC
3
TXD
1
5
4
TX0
CANH
CANL
7
6
SJA1000
V
ref
CAN
BUS LINE
CAN
TJA1050
CONTROLLER
RXD
RX0
2
8
GND
S
60 Ω
60 Ω
MICRO-
CONTROLLER
47 nF
MGS380
Fig.3 Application information.
+
5 V
100
nF
V
CC
3
TXD
1 nF
1 nF
CANH
CANL
1
5
4
7
6
V
ref
TRANSIENT
GENERATOR
TJA1050
RXD
MGS379
2
8
GND
S
15 pF
The waveforms of the applied transients shall be in accordance with “ISO 7637 part 1”, test pulses 1, 2, 3a and 3b.
Fig.4 Test circuit for automotive transients.
2003 Oct 22
8
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
MGS378
V
RXD
HIGH
LOW
(V)
hysteresis
0.5
0.9
V
i(dif)(bus)
Fig.5 Hysteresis of the receiver.
+
5 V
handbook, halfpage
100
nF
V
CC
3
TXD
CANH
CANL
1
5
4
7
6
V
ref
R
C
L
L
TJA1050
60 Ω
100 pF
RXD
2
8
GND
S
15 pF
MGS376
Fig.6 Test circuit for timing characteristics.
9
2003 Oct 22
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
HIGH
LOW
TXD
CANH
CANL
dominant
(BUS on)
0.9 V
0.5 V
(1)
V
i(dif)(bus)
recessive
(BUS off)
HIGH
0.7V
CC
RXD
0.3V
CC
LOW
t
t
d(TXD-BUSon)
d(TXD-BUSoff)
t
t
d(BUSon-RXD)
d(BUSoff-RXD)
t
t
PD TXD-RXD
(
)
(
)
PD TXD-RXD
MGS377
(1) Vi(dif)(bus) = VCANH − VCANL
.
Fig.7 Timing diagram for AC characteristics.
6.2 kΩ
6.2 kΩ
CANL
CANH
10 nF
ACTIVE PROBE
TX
TJA1050
30
Ω
30
Ω
SPECTRUM-
ANALYZER
47 nF
GND
test PCB
MGT229
Fig.8 Basic test set-up (with split termination) for electromagnetic emission measurement (see Figs 9 and 10).
2003 Oct 22
10
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
MGT231
80
A
(dBµV)
60
40
20
0
0
10
20
30
40
50
f (MHz)
Data rate of 500 kbits/s.
Fig.9 Typical electromagnetic emission up to 50 MHz (peak amplitude measurement).
MGT233
80
A
(dBµV)
60
40
20
0
0
2
4
6
8
10
f (MHz)
Data rate of 500 kbits/s.
Fig.10 Typical electromagnetic emission up to 10 MHz (peak amplitude measurement and envelope on peak
amplitudes).
2003 Oct 22
11
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
30 Ω
30 Ω
CANL
CANH
4.7 nF
RF VOLTMETER
AND POWER
AMPLIFIER
TX
TJA1050
50
Ω
RF SIGNAL
GENERATOR
RX
TJA1050
GND
test PCB
MGT230
Fig.11 Basic test set-up for electromagnetic immunity measurement (see Fig.12).
MGT232
30
V
RF(rms)
(V)
max RF voltage reached with no errors
20
10
0
−1
2
3
10
1
10
10
10
f (MHz)
Data rate of 500 kbits/s.
Fig.12 Typical electromagnetic immunity.
12
2003 Oct 22
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
BONDING PAD LOCATIONS
COORDINATES(1)
SYMBOL
TXD
PAD
x
y
8
7
6
5
handbook, halfpage
1
2
3
4
5
6
7
8
103
740
103
85
GND
VCC
886.5
1371.5
1394
998
111
TJA1050U
RXD
Vref
111
test pad
1094
1115
1115
1097
CANL
CANH
S
x
0
1
2
3
4
538.5
103
0
MGS381
y
Note
The backside of the bare die must be connected to ground.
1. All x/y coordinates represent the position of the centre
of each pad (in µm) with respect to the lefthand bottom
corner of the top aluminium layer (see Fig.13).
Fig.13 Bonding pad locations.
2003 Oct 22
13
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
PACKAGE OUTLINE
SO8: plastic small outline package; 8 leads; body width 3.9 mm
SOT96-1
D
E
A
X
v
c
y
H
M
A
E
Z
5
8
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
4
e
w
M
detail X
b
p
0
2.5
5 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
(1)
(1)
(2)
UNIT
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
Z
θ
1
2
3
p
E
max.
0.25
0.10
1.45
1.25
0.49
0.36
0.25
0.19
5.0
4.8
4.0
3.8
6.2
5.8
1.0
0.4
0.7
0.6
0.7
0.3
mm
1.27
0.05
1.05
0.041
1.75
0.25
0.01
0.25
0.01
0.25
0.1
8o
0o
0.010 0.057
0.004 0.049
0.019 0.0100 0.20
0.014 0.0075 0.19
0.16
0.15
0.244
0.228
0.039 0.028
0.016 0.024
0.028
0.012
inches 0.069
0.01 0.004
Notes
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-18
SOT96-1
076E03
MS-012
2003 Oct 22
14
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
SOLDERING
If wave soldering is used the following conditions must be
observed for optimal results:
Introduction to soldering surface mount packages
• Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
• For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is
recommended.
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
Reflow soldering
The footprint must incorporate solder thieves at the
downstream end.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Driven by legislation and environmental forces the
• For packages with leads on four sides, the footprint must
be placed at a 45° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
worldwide use of lead-free solder pastes is increasing.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250 °C or 265 °C, depending on solder
material applied, SnPb or Pb-free respectively.
Typical reflow peak temperatures range from
215 to 270 °C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
• below 220 °C (SnPb process) or below 245 °C (Pb-free
process)
Manual soldering
– for all BGA and SSOP-T packages
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300 °C.
– for packages with a thickness ≥ 2.5 mm
– for packages with a thickness < 2.5 mm and a
volume ≥ 350 mm3 so called thick/large packages.
• below 235 °C (SnPb process) or below 260 °C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm3 so called small/thin packages.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320 °C.
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
2003 Oct 22
15
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
Suitability of surface mount IC packages for wave and reflow soldering methods
SOLDERING METHOD
PACKAGE(1)
WAVE
not suitable
REFLOW(2)
BGA, LBGA, LFBGA, SQFP, SSOP-T(3), TFBGA, VFBGA
suitable
DHVQFN, HBCC, HBGA, HLQFP, HSQFP, HSOP, HTQFP,
HTSSOP, HVQFN, HVSON, SMS
not suitable(4)
suitable
PLCC(5), SO, SOJ
LQFP, QFP, TQFP
SSOP, TSSOP, VSO, VSSOP
PMFP(8)
suitable
suitable
not recommended(5)(6) suitable
not recommended(7)
suitable
not suitable
not suitable
Notes
1. For more detailed information on the BGA packages refer to the “(LF)BGA Application Note” (AN01026); order a copy
from your Philips Semiconductors sales office.
2. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum
temperature (with respect to time) and body size of the package, there is a risk that internal or external package
cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the
Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”.
3. These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account
be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature
exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package body peak temperature
must be kept as low as possible.
4. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder
cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side,
the solder might be deposited on the heatsink surface.
5. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction.
The package footprint must incorporate solder thieves downstream and at the side corners.
6. Wave soldering is suitable for LQFP, TQFP and QFP packages with a pitch (e) larger than 0.8 mm; it is definitely not
suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
7. Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than
0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
8. Hot bar or manual soldering is suitable for PMFP packages.
REVISION HISTORY
REV
DATE
CPCN
DESCRIPTION
Product specification (9397 750 12157)
Modification:
4
3
20031013
−
−
• Added recommendation to connect unused pin S to ground
• Added Chapter REVISION HISTORY
Product specification (9397 750 09778)
20020516
2003 Oct 22
16
Philips Semiconductors
Product specification
High speed CAN transceiver
TJA1050
DATA SHEET STATUS
DATA SHEET
STATUS(1)
PRODUCT
STATUS(2)(3)
LEVEL
DEFINITION
I
Objective data
Development This data sheet contains data from the objective specification for product
development. Philips Semiconductors reserves the right to change the
specification in any manner without notice.
II
Preliminary data Qualification
This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product.
III
Product data
Production
This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in order
to improve the design, manufacturing and supply. Relevant changes will
be communicated via a Customer Product/Process Change Notification
(CPCN).
Notes
1. Please consult the most recently issued data sheet before initiating or completing a design.
2. The product status of the device(s) described in this data sheet may have changed since this data sheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
DEFINITIONS
DISCLAIMERS
Short-form specification
The data in a short-form
Life support applications
These products are not
specification is extracted from a full data sheet with the
same type number and title. For detailed information see
the relevant data sheet or data handbook.
designed for use in life support appliances, devices, or
systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips
Semiconductors customers using or selling these products
for use in such applications do so at their own risk and
agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Limiting values definition Limiting values given are in
accordance with the Absolute Maximum Rating System
(IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device.
These are stress ratings only and operation of the device
at these or at any other conditions above those given in the
Characteristics sections of the specification is not implied.
Exposure to limiting values for extended periods may
affect device reliability.
Right to make changes
Philips Semiconductors
reserves the right to make changes in the products -
including circuits, standard cells, and/or software -
described or contained herein in order to improve design
and/or performance. When the product is in full production
(status ‘Production’), relevant changes will be
Application information
Applications that are
communicated via a Customer Product/Process Change
Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these
products, conveys no licence or title under any patent,
copyright, or mask work right to these products, and
makes no representations or warranties that these
products are free from patent, copyright, or mask work
right infringement, unless otherwise specified.
described herein for any of these products are for
illustrative purposes only. Philips Semiconductors make
no representation or warranty that such applications will be
suitable for the specified use without further testing or
modification.
2003 Oct 22
17
Philips Semiconductors – a worldwide company
Contact information
For additional information please visit http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.
© Koninklijke Philips Electronics N.V. 2003
SCA75
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
R16/04/pp18
Date of release: 2003 Oct 22
Document order number: 9397 750 12157
相关型号：
TJA1050T/VM
IC DATACOM, INTERFACE CIRCUIT, PDSO8, 3.90 MM, ROHS COMPLIANT, PLASTIC, MS-012, SOT96-1, SOP-8, Network Interface
NXP
©2020 ICPDF网 联系我们和版权申明