MPB150-2024G [POWER-ONE]
Dual-Output AC-DC Series; 双输出AC- DC系列型号: | MPB150-2024G |
厂家: | POWER-ONE |
描述: | Dual-Output AC-DC Series |
文件: | 总4页 (文件大小:97K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MPB150 Dual-Output AC-DC Series Data Sheet
Features
• RoHS compliant for all six substances
• High power density in an industry-standard 3" x 5"
footprint
• Power Factor Correction (PFC) meets EN61000-3-2
• Main output remote sense
• Power Good signals
• CE marked to Low Voltage Directive
• Input transient & ESD compliance to
EN61000-4-2/-3/-4/-5
Description
The MPB150 Series incorporates patented high efficiency circuitry, high power density and active Power Factor
Correction (PFC) to meet the requirements of networking and data communications systems, as well as commercial
and industrial configurations.
MPB150’s deliver a regulated main output plus a second 12V output for fans or other system functions. The MPB150
is rated for convection as well as forced-air cooling. Full output power is available with as few as 15 Cubic Feet per
Minute (CFM) forced-air cooling.
The MPB150 product line is approved to the latest international regulatory standards, and displays the CE Mark.
Model Selection
OUTPUT
VOLTAGE
(VOLTS)
MAXIMUM OUTPUT
CURRENT (AMPS),
130 LFM
TOTAL
REGULATION
%
RIPPLE & NOISE
% pk-pk
MODEL
REGULATION RANGE
(NOTE 1)
MPB150-2012G
(NOTE 2, 3, 4)
+12V
12V
+24V
12V
+48V
12V
12.5A
0.5A
6.0A
0.5A
±.1A
0.5A
±±3
±53
±±3
±53
±±3
±53
13
13
13
13
13
13
11.64V to 12.±6V
11.40V to 12.60V
2±.28V to 24.72V
11.40V to 12.60V
46.56V to 49.44V
11.40V to 12.60V
MPB150-2024G
(NOTE 2, 3, 4)
MPB150-2048G
(NOTE 2, 3, 4)
NOTES: 1) Maximum peak-to-peak noise expressed as a percentage of output voltage, 20 MHz bandwidth.
2) Maximum forced-air output power is 150 watts with 15 CFM airflow.
3) Maximum convection output power is 70 watts.
4) V2 is isolated from V1 and can be used as a negative or positive output.
APR 28, 2006 revised to JAN 24, 2007
Page 1 of 4
www.power-one.com
MPB150 Dual-Output AC-DC Series Data Sheet
Input Specifications
PARAMETER
CONDITIONS/DESCRIPTION
MIN
90
47
90
17
NOM
MAX
264
6±
UNITS
VAC
Hz
VAC
ms
Input Voltage- AC
Input Frequency
Brownout Protection
Hold-up Time
Continuous input range.
AC Input.
Lowest AC input voltage that regulation is maintained with full rated loads.
Over full AC input voltage range at full rated load.
90 VAC at full rated load.
Input Current
2.2
ARMS
Input Protection
Inrush Surge Current
Non-user serviceable internally located AC input line fuse, 250 VAC, ±.15A.
Internally limited by thermistor,
one cycle, 25° C.
110VAC:
220VAC:
2±
46
APK
kHz
Power Factor Circuitry
Operating Frequency
Active PFC meets requirements of EN61000-±-2.
Switching frequency of main transformer.
45
Output Specifications
PARAMETER
CONDITIONS/DESCRIPTION
MIN
75
5
NOM
MAX
UNITS
3
Watts
Efficiency
Minimum Loads
Full Load, 2±0VAC. Varies with distribution of loads among outputs.
80
85
V1 load for full regulation on V2. All models operate
at no load without any damage and meet all specs on V1 above 0 amps.
Full load, 20 MHz bandwidth.
At 15 CFM forced-air cooling. See Application Note for details.
Convection: Consult Factory.
Output voltage overshoot/undershoot at turn-on.
Varies by output. Total regulation includes: line changes from 85-1±2 VAC
Ripple and Noise
Output Power (Note 1)
See Model Selection Chart
150
Watts
3
Overshoot /Undershoot
Regulation
10
See Model Selection Chart
or 170-264 VAC, changes in load starting at 203 load and changing to 1003 load.
Transient Response
Turn-on Delay
Turn-on Rise Time
Maximum deviation due to a 253 load change with unit at 753 load.
Time required for initial output voltage stabilization.
Time required for output voltage to rise from 103 to 903.
±
3
Sec
ms
0.2
0.2
1.5
20
Interface Signals and Internal Protection
PARAMETER
CONDITIONS/DESCRIPTION
MIN
NOM
MAX
UNITS
Overvoltage Protection
V1 output.
MPB150-2012
MPB150-2024
MPB150-2048
1±.5
26.9
57.6
16.5
±1.1
62.4
VDC
Overload Protection
Fully protected against output short circuit or overload. Automatic recovery upon
removal of overload condition.
Remote Sense (Note 1)
Power Good Signal
Total (+sense and -sense) voltage compensation for cable losses.
500
500
mV
AC/DC indicator - This signal indicates the status of the AC input or DC outputs.
When there is sufficient AC voltage and the outputs are operating normally, an
open collector signal is provided.
Turn-On delay time from application of AC:
Warning time before outputs go out of regulation:
50
5
ms
Warning time before outputs deviate ±103 from the nominal value:
15
Sink Current
Pull-up Voltage
20
±0
mA
V
Power Supply OK Signal
Provided on dual-output models. Open collector signal intended to drive an LED.
Closed collector occurs when the Power Good Signal is in its open collector state.
Sink Current
Pull-up Voltage
20
±0
mA
V
Thermal Shutdown
Current Share
Protected against overtemperature conditions.
Unit recovers when overtemperature condition is removed.
Up to 4 units can be connected in parallel.
There are some limits for parallel operation. See Applications Note.
N+1 redundancy is provided. V2 needs an external isolation diode for N+1 operation.
Isolation Diode
Internal isolation diode is provided on V1.
NOTES: 1) Negative (-) sense must be connected to output common or load common for proper power supply operation.
APR 28, 2006 revised to JAN 24, 2007
Page 2 of 4
www.power-one.com
MPB150 Dual-Output AC-DC Series Data Sheet
Safety, Regulatory, and EMI Specifications
PARAMETER
CONDITIONS/DESCRIPTION
MIN
NOM
MAX
UNITS
Agency Approvals
UL60950-1.
CSA 22.2 No. 60950-1.
EN60950 (TÜV).
IEC60950-1.
(Approvals Pending)
Dielectric Withstand Voltage
AC to chassis.
Input to output.
1500
±000
VAC
VDC
Electromagnetic Interference
ESD Susceptibility
Flicker
EN55022 Conducted.
Per EN61000-4-2, Level 4
Per EN61000-±-±.
Class A
6
8
dB
kV
Radiated Susceptibility
EFT/Burst
Per EN61000-4-±.
Per EN61000-4-4.
±
V/m
kV
1
Input Transient Protection
RF Immunity
Magnetic Fields
Per EN61000-4-5, Level ±, 2 kV (Line-to-Gnd) minimum, 1 kV (Line-to-Line) minimum.
Per EN61000-4-6. 0.15 to 80 MHz (1 kHz sinewave)
Per EN61000-4-8.
±
1
V/m
A/m
Voltage Dips
Per EN61000-4-11.
Insulation Resistance
Leakage Current
Input to output.
Per EN60950 (264 VAC)
10
M⍀
mA
1.0
Environmental Specifications
PARAMETER
CONDITIONS/DESCRIPTION
MIN
NOM
MAX
UNITS
Altitude
Operating
Non-Operating
10K
50K
ASL Feet
Operating Temperature
Derate linearly from 50 to 70°C to 503 power at 70°C.
MPB150 models will operate at -20°C, but will not meet all specifications.
At 1003 load:
0
50
°C
°C
Storage Temperature
Forced-Air Cooling
-40
85
Forced-air cooling of 15 CFM is required for full output power. Air velocity
is measured with power supply mounted on 0.±75" (9.5mm) standoffs.
Airflow direction is from the input section to the output section.
See Application Note for details.
Temperature Coefficient
Relative Humidity
Shock
Included in total regulation of outputs.
Non-Condensing.
Operating: 11 ±±ms, ± axes, Half Sine.
Non-operating: 11 ±±ms, ± axes, Half Sine.
5
85
15
40
3RH
G
pk
Vibration
Operating:
Random vibration, 5-500 Hz, 10 minutes each axis.
2.4
6.0
GRMS
GRMS
Non-Operating: Random vibration, 5-500 Hz, 10 minutes each axis.
APR 28, 2006 revised to JAN 24, 2007
Page 3 of 4
www.power-one.com
MPB150 Dual-Output AC-DC Series Data Sheet
Mechanical Drawing (-2012G, -2024G, & -2048G Models)
WEIGHT: 0.63 lb. (0.3 kg)
J1 - AC INPUT CONNECTOR
Pin 1
Pin 2
Pin 3
NEUTRAL
NO PIN
LINE
5.00"
(127.0)
Ø 0.16" (4 PL)
(4.06)
J2 -
Pin 1
MPB150
-2012G
4.55"
(115.57)
-2024G -2048G
+24V +48V
+24V +48V
+12V
+12V
+12V
RTN
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
J2 - V 1 DC OUTPUT
CONNECTOR
+24V
RTN
RTN
RTN
+48V
RTN
RTN
RTN
RTN
TOP VIEW
RTN
PIN #1
PIN #1
J3 -
3.00"
(76.2)
2.78"
(70.6)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
RTN
- SENSE
+ SENSE
2.56"
(65.02)
J3- SIGNAL
CONNECTOR
PIN #1
CURRENT SHARE
POWER GOOD
PIN #1
J4- V2 DC OUTPUT
CONNECTOR
POWER SUPPLY OK
FASTENER
CLEARANCE
AREA (4 PL)
J4 -
SAFETY GROUND
CONNECTION POINT
Pin 1
Pin 2
+12V
SCREWS SHOWN
FOR REFERENCE
ONLY
+12V RTN
0.06"
(1.5)
1.00"
(25.4)
1.25"
(31.75)
END VIEW
SIDE VIEW
PRINTED CIRCUIT BOARD
0.19"
(4.8)
Mating Connectors
NOTE: Part numbers are MOLEX; equivalents are acceptable.
MPB150
-2012G
-2024G
-2048G
J1
J2
J3
J4
Housing
Pins
09-50-8031
08-52-0113
09-50-8061
08-52-0113
22-01-3067
08-50-0114
22-01-3027
08-50-0114
Housing
Pins
Housing
Pins
Housing
Pins
NUCLEAR AND MEDICALAPPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components
in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective
divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
APR 28, 2006 revised to JAN 24, 2007
Page 4 of 4
www.power-one.com
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明