PA4401DN-T7 [PROTEC]
Click-Pop Suppression Device; 点击噼噗声抑制装置型号: | PA4401DN-T7 |
厂家: | PROTEK DEVICES |
描述: | Click-Pop Suppression Device |
文件: | 总7页 (文件大小:108K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PA4401
Click-Pop Suppression Device
ANALO G P RO DUCTS DIVIS IO N
FEATURES
GENERAL DESCRIPTION
9V or 12V operation
3V RMS Capability
Power-Up and Power-Down “POP” suppression
ESD protected outputs
The PA4401 provides click-pop suppression for devices that
lack a click-less/pop-less startup or shutdown. The PA4401 is
placed between the codec and the output coupling capacitor.
8-Lead SOIC package
Series operation
Only 1 external component required
Ron (On resistance):
Ron Flatness:
The click-pop noise is generated at the coupling capacitors
while the system is starting up as well as shutting down.
The PA4401 controls the ramping of the DC voltage into the
coupling capacitors thus reducing the click-pop noise
generated during the startup and shutdown.
0.8 ohms
0.4 ohms
<1%
Total Harmonic Distortion:
Current drain:
The start time can be controlled or changed using an external
capacitor.
<5mA
Load:
600 ohms
ESD protection circuits are provided at the inputs and outputs
of the device.
The PA4401 consumes less than 5mA of current and
provides a THD of less than 1% for a load of 600 ohms.
APPLICATIONS
Portable DVD players
Set-top boxes
Car Audio
High End Audio
Televisions
The PA4401 is available in an 8L-SOIC and DFN-6
Packages.
Stereo Systems
Digital Video Recorders
LCD TVs
FUNCTIONAL DIAGRAM
Home Theater systems
Input
Pre
Amp
Vcc
Output
Output
Pin Layout and Description
Startup
&
Shutdown
Control
VCC
1
2
3
4
8
7
6
5
CEXT
CEXT
8
VCC
SOIC-8
1
In 1
In 2
Out 1
Out 2
Input
7 Out 1
In 1
In 2
2
Pre
Amp
DFN-6
PA4401
3
4
Out 2
GND
6
5
SEL
GND
SEL
Figure 1: Functional block diagram of PA4401
Ordering Information
Temperature
Range
Pin
Symbol
Designation
Voltage
Package
SOIC-8
DFN-6
Part Number
PA4401DQ-T7
PA4401DN-T7
1
2
3
4
5
6
7
8
VCC
In1
Audio Input 1
Audio Input 2
-40 to 85 °C
In2
SEL
GND
Out2
Out1
CEXT
Select 12 or 9Volt Operation
Ground
SEL Logic
Audio Output 2
System Voltage
SEL Status
Ground
VCC
Audio Output 1
9V
External Capacitor
12V
561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480) 632-1715
www.protekanalog.com
95025. Rev0.0 12/10; PATENT PENDING; CONFIDENTIAL; COVERED BY NON DISCLOSURE AGREEMENT
NOT FOR USE IN LIFE SUPPORT SYSTEMS
PA4401
Click-Pop Suppression Device
ANALO G P RO DUCTS DIVIS IO N
ABSOLUTE MAXIMUM RATINGS
(All Voltages are referenced to GND)
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
V
........................................................................................+15V
CC
Continuous Current (IN_, OUT_).....................................±150mA
Continuous Current (All Other Pins) .................................±20mA
Continuous Power Dissipation (T
= +70°C)
A
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS.
°C
Unless otherwise specified, VDD=12V, SEL = VDD,TA = Ambient Temperature = 25
.
Limit
Symbol
Parameter
Condition
Unit
Min
Typical
Max
12.0
5
VDD
IDD
TA
Power Supply
Normal Operation
9.0
V
Supply Current
Normal Operation
mA
ºC
Ambient Temperature
Normal Operation
-40
+85
2.0
1.8
VGATE = 10V, IDFET = 100mA
VGATE = 15V, IDFET = 100mA
1.8
1.5
RON
FET ON Resistance
Ω
VGATE = 20V, IDFET = 100mA
1.3
15
1.5
RFLAT(ON) ON Resistance Flatness
m
Ω
Over Input Voltage Range
RL = 600
f = 1kHz
f = 20kHz
Ω, VSIG = 2VRMS
THD
Total Harmonic Distortion
.020
1
%
XTALK
QIRR
VSIG
Crosstalk (on)
-100
-108
dB
dB
Off Isolation
f = 20kHz RL= 600
Normal Operation
HBM
Ω
Analog Signal Range
ESD Protection
2.0
VRMS
kV
VESD
ROUT
fCO
4
Output Discharge Resistor
Bandwidth
100
>100
90%
k
Ω
kHz
VCC
VUVLO
Power Off Threshold
VCC Falling
561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480) 632-1715
www.protekanalog.com
95025. Rev0.0 12/10; PATENT PENDING; CONFIDENTIAL; COVERED BY NON DISCLOSURE AGREEMENT
NOT FOR USE IN LIFE SUPPORT SYSTEMS
PA4401
Click-Pop Suppression Device
ANALOG PRODUCTS DIVISION
DETAILED DESCRIPTION
Figure2. Shows the normal setup of a Pre Amplifier system. Since the system is built on a single ended power supply the
outputs of the pre-amplifier need to be routed through a bypass capacitor to get rid of the DC bias.
Pre
Amp
+
Power
Amp
Pre
Amp
+
Power
Amp
Figure 2: Normal setup for a pre amplifier output
When the power supply to the system is turned ON there is a spike in the output of the system because of the charging of
various components in the system. This spike is called a “Click or Pop Noise”. When this click/pop noise passes through the
Power Amplifiers, the noise is amplified and listeners hear an audible ‘pop’ which causes discomfort. The reverse operation
happens when the system is powering down. These operations are shown below in figure3. The top waveform shows the power
supply Powering Up and Powering Down. The middle waveform shows the voltage appearing at the positive terminal of the
bypass capacitor. The bottom waveform shows the voltage at the output of the bypass capacitor. This is the Pop-Noise that is
amplified by the power amplifier.
t
t
50mS
VCC
50mS
Power Supply Waveform
0
VCC/2
Bypass capacitor input plate
System output
>500mV
start-up “pop”
0
>500mV
shutdown “pop”
time
mSec
Figure 3: Power Up and Power Down sequences and waveforms
561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 414-5141
www.protekanalog.com
95025. Rev.0. 05/2008
NOT FOR USE IN LIFE SUPPORT SYSTEMS
PA4401
Click-Pop Suppression Device
ANALOG PRODUCTS DIVISION
CONNECTION DIAGRAM
The PA4401 will be placed after the pre-amplifier and before the output bypass capacitors.
VCC
Pre
Amp
+
IN
OUT
Pre
Amp
+
IN
OUT
Figure 4: Typical Connection Configuration for PA4401
STARTUP
At Startup, the Power supply ramps from 0V to VCC between 20 -200ms. The PA4401 detects the ramp in the voltage at its inputs
and controls the ramp rate of the DC bias voltage going to the +ve terminal of the bypass capacitor. The ramping behavior of the
device can be controlled by an external capacitor. This startup operation is shown in figure 5.
SHUTDOWN
At Shutdown, The PA4401 detects a “power fail” condition and the control switches are turned off, opening the connection
between INx and OUTx providing a discharge path through an internal 100Kꢀ resistor for the bypass capacitor. The time
constant of the internal resistor and by-pass capacitor, allows for a slow discharge, which will prevent any audible “pop”
appearing at the system output. This shutdown operation is shown in figure 5.
t
t
50mS
50mS
VCC
Power Supply Waveform
0
VCC
PA4401 slows
down transition at
coupling capacitor
Bypass capacitor input plate
System output
<50mV
Start-up “pop”
0
<50mV
shutdown “pop”
time
mSec
Figure 5: Power-Up and Power-Down sequences and waveforms with PA4401
561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 414-5141
www.protekanalog.com
95025. Rev.0. 05/2008
NOT FOR USE IN LIFE SUPPORT SYSTEMS
PA4401
Click-Pop Suppression Device
ANALOG PRODUCTS DIVISION
Test Circuit for Turn-On time vs. CEXT and Turn-Off Time vs. CEXT
VDD
VINx
INx
VOUTx
90%
VOUTx
Control
Element
50%
50%
CEXT
10%
tON
tOFF
R1
1Mꢀ
C1
Turn-On time vs. Cext
Turn-Off time vs. Cext
800
60
50
40
30
20
10
0
700
600
500
400
300
200
100
0
1
10
100
Capacitor Value (nF)
1000
10000
1
10
100
1000
10000
Capacitor Value (nF)
CEXT (nF)
1
tON (mS)
3.6
tOFF (mS)
23
23
28
32
48
10
12
100
42
1000
2200
300
690
561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 414-5141
www.protekanalog.com
95025. Rev.0. 05/2008
NOT FOR USE IN LIFE SUPPORT SYSTEMS
PA4401
Click-Pop Suppression Device
ANALOG PRODUCTS DIVISION
SO-8 PACKAGE OUTLINE & DIMENSIONS
PACKAGE OUTLINE
SO-8
-A-
8
5
0.0I0” (0.25 MM)
B
M
+
M
PACKAGE DIMENSIONS
-B -
P
4 PL
MILLIMETERS
INCHES
I
4
DIM
MIN
MAX
MIN
MAX
A
B
C
D
F
G
J
K
P
R
4.80
3.80
1.35
0.35
0.40
5.00
4.00
1.75
0.49
1.250
0.189
0.150
0.054
0.014
0.016
0.196
0.157
0.068
0.019
0.049
D
G
C
45
1.27 BSC 1.27 BSC 0.05 BSC 0.05 BSC
0.18
0.10
5.80
0.25
0.25
0.25
6.20
0.50
0.007
0.004
0.229
0.010
0.009
0.008
0.244
0.019
0 - I0
-T-
J
F
NOTES
0.0I0” (0.25 MM)
T B
A
S S
M
+
8 PL
1. - T - = Seating Plane and Datum Surface.
2. Dimensions “A” and “B” are Datum.
3. Dimensions “A” and “B” do not include mold protrusion.
4. Maximum mold protrusion is 0.015” (0.380 mm) per side.
5. Dimensioning and tolerances per ANSI Y14.5M, 1982.
6. Dimensions are exclusive of mold flash and metal burrs.
MOUNTING PAD
0.050 + 0.005”
0.030 + 0.005”
TAPE & REEL/BULK ORDERING NOMENCLATURE
1. Surface mount product is taped and reeled in accordance with EIA-481.
2. Suffix-T7 = 7 Inch Reel - 1,000 pieces per 12mm tape.
3. Suffix-T13 = 13 Inch Reel - 2,500 pieces per 12mm tape.
4. No Suffix = Product Shipped in Tubes of 98 pcs per Tube.
0.I60 + 0.005”
0.245” M!"
Outline & Dimensions: Rev 1 - 11/01, 06009
0.045 + 0.005”
561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 414-5141
www.protekanalog.com
95025. Rev.0. 05/2008
NOT FOR USE IN LIFE SUPPORT SYSTEMS
PA4401
Click-Pop Suppression Device
ANALOG PRODUCTS DIVISION
Package Outline and Dimensions DFN-8
Dim
MILLIMETERS
MIN
TYP
3.00
3.00
0.75
0.25
0.40
0.02
0.65
2.30
1.55
MAX
L1
P1
P2
P3
L1
L2
L3
p
2.95
2.95
0.70
0.23
0.35
0.02
0.60
2.25
1.50
3.05
3.05
0.80
0.27
0.45
0.02
0.70
2.35
1.60
p
P1
L2
PA4401
P2
G2
XXXX
G1
G2
Pin 1 Indicator
4
1
0.30mm
0.65mm
G1
TOP VIEW
BOTTOM VIEW
0.60mm
1.85mm
L3
P3
2.74mm
SIDE VIEW
2.60mm
Recommended Land Pattern
Tape and Reel Specifications
Reel Dia
A0
B0
K0
D
E
F
W
P0
P2
P
t-max
0.25
178 (7”)
3.00±0.10
3.00±0.10
0.85±0.10
1.50±0.10
1.75±0.10
3.50±0.05
12.00±0.30
4.00±0.10
2.00±0.05
4.00±0.10
10 Pitches Cumulative
Tolerance on Tape± 0.2
P0
P2
D
t
E
Pin 1
Top cover tape
indicated
by Dot
A0
F
W
K0
B0
P
Life Support Policy
PROTEK ANALOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF PROTEK DEVICES.
561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 414-5141
www.protekanalog.com
95025. Rev.0. 05/2008
NOT FOR USE IN LIFE SUPPORT SYSTEMS
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明