PE4271-EK [PSEMI]
SPST CATV UltraCMOS? Switch DC - 3000 MHz; SPST CATV的UltraCMOS ?开关直流 - 3000兆赫型号: | PE4271-EK |
厂家: | Peregrine Semiconductor |
描述: | SPST CATV UltraCMOS? Switch DC - 3000 MHz |
文件: | 总8页 (文件大小:300K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Product Specification
PE4271
SPST CATV UltraCMOS™ Switch
DC - 3000 MHz
Product Description
The PE4271 is a is a high-isolation Switch designed for CATV
applications, covering a broad frequency range from near DC
up to 3000 MHz. This single-supply SPST switch offers a
single-pin CMOS control interface with industry leading CTB
performance. It also provides low insertion loss, high isolation
and extremely low bias requirements while operating on a
single 3-volt supply. In a typical CATV application, the PE4271
provides for a cost effective and manufacturable solution vs.
mechanical relays.
Features
• Integrated 0.25 watt terminations
• CTB performance of 90 dBc
• High isolation: 85 dB at 5 MHz, 60 dB
at 1000 MHz
• Low insertion loss: 0.5 dB at 5 MHz,
0.70 dB at 1000 MHz
• High input IP2: >80 dBm
• CMOS/TTL single-pin control
• Single +3-volt supply operation
• Extremely low bias: 8 µA @ 3 V
• Available in a 6-lead DFN package
The PE4271 is manufactured on Peregrine’s UltraCMOS™
process, a patented variation of silicon-on-insulator (SOI)
technology on a sapphire substrate, offering the performance
of GaAs with the economy and integration of conventional
CMOS.
Figure 1. Functional Diagram
Figure 2. Package Type
6-lead DFN
RF1
RF2
75
CMOS
Control
Driver
CTRL
Table 1. Electrical Specifications @ +25 °C (ZS = ZL = 75 ꢀ)
Parameter
Condition
Minimum
Typical
Maximum
Units
Operating Frequency1
DC
3000
MHz
DC – 50 MHz
0.50
0.70
85
60
0.65
0.85
Insertion Loss
Isolation
dB
dB
1000 MHz
DC – 50 MHz
1000 MHz
80
58
DC - 1000 MHz
VCNTL = 3.0V
Return Loss
15
30
16
33
dB
Input 1 dB Compression2,4
CTB / CSO
1000 MHz
dBm
dBc
77 & 110 channels;
PO = 44 dBmV
-90
Input IP22
Input IP32
Video Feedthrough3
1000 MHz
1000 MHz
80
50
dBm
dBm
mVpp
µS
15
Switching Time
2
Notes: 1. Device linearity will begin to degrade below 1 MHz.
2. Measured in a 50 Ω system.
3. Measured with a 1 ns risetime, 0/3 V pulse and 500 MHz bandwidth.
4. Note Absolute Maximum ratings in Table 3.
Document No. 70-0149-03 │ www.psemi.com
©2005 Peregrine Semiconductor Corp. All rights reserved.
Page 1 of 8
PE4271
Product Specification
Figure 3. Pin Configuration
Table 4. DC Electrical Specifications
Parameter
Min
Typ
Max
Unit
VDD Power Supply
IDD Power Supply Current
2.7
3.0
3.3
V
VDD
GND
RF1
1
2
3
6
5
4
RF2
8
20
µA
(VDD = 3V, VCTRL = 3V)
Exposed
Solder Pad
(bottom side)
GND
CTRL
Control Voltage High
Control Voltage Low
0.7xVDD
0
5
V
V
0.3xVDD
Figure 4. Typical Application Block Diagram
Premium
Channel
Filter
PE4271
Table 2. Pin Descriptions
2-way
CATVin
CATVout
Pin
No.
Pin
Name
Splitter
Description
PE4271
1
2
3
VDD
GND
RF1
Nominal 3V supply connection.
Ground connection. 2
RF port. 1
Table 5. Control Logic Truth Table
CMOS or TTL logic level:
Control Voltage (CTRL)
Signal Path (RF1 to RF2)
4
CTRL
High = RF1 to RF2 signal path
High1
ON
Low = RF1 isolated from RF2
Ground connection. 3
RF port. 1
Low
OFF
5
6
GND
RF2
Notes: 1. CTRL accepts both CMOS and TTL voltage leads.
Notes: 1. Both RF pins must be held at 0 VDC or require external DC
blocking capacitors
Electrostatic Discharge (ESD) Precautions
2. The exposed pad must be soldered to the ground plane for
proper switch performance.
When handling this UltraCMOS™ device, observe
the same precautions that you would use with other
ESD-sensitive devices. Although this device
contains circuitry to protect it from damage due to
ESD, precautions should be taken to avoid
exceeding the rating specified in Table 3.
Table 3. Absolute Maximum Ratings
Symbol Parameter/Condition
Min
-0.3
-0.3
-65
Max
4.0
5.5
150
85
Unit
V
V
°C
°C
VDD
VI
Power supply voltage
Voltage on CTRL input
Storage temperature
Operating temperature
Device Description
TST
TOP
-40
The PE4271 high isolation SPST CATV Switch is
designed to support CATV applications such as
premium channel service connect/disconnect switch
blocks. This function is typically performed by bulky
and expensive mechanical switches. The high
isolation characteristics (60 dB at 1 GHz, 85 dB at
5 MHz), high compression point, and an integrated
75 ꢀ (0.25 watt) input termination make the PE4271
an ideal, low cost solution.
Input power (50ꢀ),
PIN
33/24
500
dBm
V
CTRL=1/CTRL=0
ESD voltage
VESD
(Human Body Model)
Absolute Maximum Ratings are those values listed
in the above table. Exceeding these values may
cause permanent device damage. Functional
operation should be restricted to the limits in the DC
Electrical Specifications table. Exposure to absolute
maximum ratings for extended periods may affect
device reliability.
The control logic input pin (CTRL) is typically driven
by a 3-volt CMOS logic level signal, and has a
threshold of 50% of VDD. For flexibility to support
systems that have 5-volt control logic drivers, the
control logic input has been designed to handle a 5-
volt logic HIGH signal. (A minimal current will be
sourced out of the VDD pin when the control logic
Latch-Up Avoidance
Unlike conventional CMOS devices, UltraCMOS™
devices are immune to latch-up.
input voltage level exceeds VDD.
)
©2005 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0149-03 │ UltraCMOS™ RFIC Solutions
Page 2 of 8
PE4271
Product Specification
Typical Performance Data @ -40 °C to 85 °C (Unless Otherwise Noted)
(75 Ω impedance except as indicated)
Figure 5. Insertion Loss - RF1 to RF2
Figure 6. 1dB Compression & 3rd Order
Intercept Point (T = 25°C)
Figure 7. Isolation - RF1 to RF2
Document No. 70-0149-03 │ www.psemi.com
©2005 Peregrine Semiconductor Corp. All rights reserved.
Page 3 of 8
PE4271
Product Specification
Typical Performance Data @ -40 °C to 85 °C (Unless Otherwise Noted)
(75-ohm impedance)
Figure 8. RF1 Return Loss (Switch = ON)
Figure 9. RF1 Return Loss (Switch = OFF)
Figure 10. RF2 Return Loss (Switch = ON)
©2005 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0149-03 │ UltraCMOS™ RFIC Solutions
Page 4 of 8
PE4271
Product Specification
Figure 11. Evaluation Board Layouts
Peregrine Specification 101/0167 (with F connectors)
Evaluation Kit
The PE4271 EK board was designed to ease
customer evaluation of Peregrine’s high
performance SPST CATV MOSFET switch. RF1
is connected through a 75 ꢀ transmission line via
the top left F connector, J1. RF2 is connected
through a 75 ꢀ transmission line via the top right
F connector, J2. A 75 ꢀ through transmission line
is available via F connectors J3 and J4. This
transmission line can be used to estimate the loss
of the PCB over the environmental conditions
being evaluated. VDD is supplied via J6-2, while
the control logic voltage is supplied via J5-2. It is
the responsibility of the customer to determine
proper supply decoupling for their design
application. It has been observed that by
removing C1 and C2 from the evaluation board
has not shown to degrade RF performance.
The board is constructed of a two metal layer FR4
material with a total thickness of 0.031”. The
bottom layer provides ground for the RF
transmission lines. The transmission lines were
designed using a coplanar waveguide model with
trace width of 0.021”, trace gaps of 0.030”,
dielectric thickness of 0.028”, metal thickness of
0.0021” and εr of 4.6. Note that the predominate
mode for these transmission lines is coplanar
waveguide with a ground plane.
Figure 12. Evaluation Board Schematic
Peregrine Specification 102/0245
Document No. 70-0149-03 │ www.psemi.com
©2005 Peregrine Semiconductor Corp. All rights reserved.
Page 5 of 8
PE4271
Product Specification
Figure 13. Package Drawing
6-lead DFN
- A -
3.00
- B -
C
L
6
5
4
0.125
C
3.00
L
PIN
MAR
1
K
C
0.10
4
1
2
3
0.10
C
0.125
4
+2°
10°
TOP
DETAIL C
-10°
VIEW
0.025
±0.025
0.100
C
C
0.70 ± 0.05
0.20 ±0.05
0.90 ±0.10
0.025±0.025
0.080
3
SEATING
SIDE
VIEW
SEE DETAIL B
PLANE
DETAIL B
- C -
C
L
0.17 MIN.
0.24
+0.08
-0.02
+0.20
-0.08
0.95
0.35
0.10
C A B
0.05
C
0.125
EXPOSED PAD
SEE DETAIL A
+0.21
0.29
1
-0.08
2
3
EXPOSED SLUG/
HEAT SINK
0.17
0.30
R0.127 TYP
R 0.15 TYP
1.21 ±0.10
0.605 ±0.05
THIS FEATURE
APPLIES TO
BOTH ENDS OF
THE PKG.
EXPOSED METALIZED
FEATURE
EXPOSED
(2X)
.20 MIN.
3
EDGE OF PLASTIC BODY
6
DETAIL A
4
5
1.05±0.05
2.01±0.10
BOTTOM VIEW
1. DIMENSIONS AND TOLERANCES ARE PER ANSi Y14.5
2. DIMENSIONS ARE IN MILLIMETERS, ANGLES ARE IN DEGREES.
3
COPLANARITY APPLIES TO EXPOSED HEAT SLUG AS WELL AS THE TERMINALS.
PROFILE TOLERANCE APPLIES TO PLASTIC BODY ONLY.
4
©2005 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0149-03 │ UltraCMOS™ RFIC Solutions
Page 6 of 8
PE4271
Product Specification
Figure 14. Tape and Reel Specifications
6-lead DFN
Table 6. Dimensions
Dimension
DFN 3x3 mm
3.23 ± 0.1
3.17 ± 0.1
1.37 ± 0.1
4 ± 0.1
Ao
Bo
Ko
P
W
8 +0.3, -0.1
0.254 ± 0.02
3000
T
R7 Quantity
R13 Quantity
N.A.
Note: R7 = 7 inch Lock Reel, R13 = 13 inch Lock Reel
Table 7. Ordering Information
Order Code
4271-01
Part Marking
4271
Description
Package
Shipping Method
12800 units / Canister
3000 units / T&R
1 / Box
PE4271-06DFN 3x3mm-12800F
PE4271-06DFN 3x3mm-3000C
PE4271-06DFN 3x3mm-EK
PE4271G-06DFN 3x3mm-12800F
PE4271G-06DFN 3x3mm-3000C
6-lead 3x3 mm DFN
6-lead 3x3 mm DFN
Evaluation Kit
4271-02
4271
4271-00
PE4271-EK
4271
4271-51
Green 6-lead 3x3 mm DFN
Green 6-lead 3x3 mm DFN
12800 units / Canister
3000 units / T&R
4271-52
4271
Document No. 70-0149-03 │ www.psemi.com
©2005 Peregrine Semiconductor Corp. All rights reserved.
Page 7 of 8
PE4271
Product Specification
Sales Offices
The Americas
North Asia Pacific
Peregrine Semiconductor Corp.
9450 Carroll Park Drive
San Diego, CA 92121
Peregrine Semiconductor K.K.
5A-5, 5F Imperial Tower
1-1-1 Uchisaiwaicho, Chiyoda-ku
Tokyo 100-0011 Japan
Tel 858-731-9400
Fax 858-731-9499
Tel: +81-3-3502-5211
Fax: +81-3-3502-5213
Europe
South Asia Pacific
Peregrine Semiconductor Europe
Commercial Products:
Bâtiment Maine
13-15 rue des Quatre Vents
F- 92380 Garches, France
Tel: +33-1-47-41-91-73
Peregrine Semiconductor
28G, Times Square,
No. 500 Zhangyang Road,
Shanghai, 200122, P.R. China
Tel: +86-21-5836-8276
Fax: +86-21-5836-7652
Fax : +33-1-47-41-91-73
Space and Defense Products:
180 Rue Jean de Guiramand
13852 Aix-En-Provence cedex 3, France
Tel: +33(0) 4 4239 3361
Fax: +33(0) 4 4239 7227
For a list of representatives in your area, please refer to our Web site at: www.psemi.com
Data Sheet Identification
Advance Information
The information in this data sheet is believed to be reliable.
However, Peregrine assumes no liability for the use of this
information. Use shall be entirely at the user’s own risk.
The product is in a formative or design stage. The data
sheet contains design target specifications for product
development. Specifications and features may change in
any manner without notice.
No patent rights or licenses to any circuits described in this
data sheet are implied or granted to any third party.
Preliminary Specification
Peregrine’s products are not designed or intended for use in
devices or systems intended for surgical implant, or in other
applications intended to support or sustain life, or in any
application in which the failure of the Peregrine product could
create a situation in which personal injury or death might occur.
Peregrine assumes no liability for damages, including
consequential or incidental damages, arising out of the use of
its products in such applications.
The data sheet contains preliminary data. Additional data
may be added at a later date. Peregrine reserves the right
to change specifications at any time without notice in order
to supply the best possible product.
Product Specification
The data sheet contains final data. In the event Peregrine
decides to change the specifications, Peregrine will notify
customers of the intended changes by issuing a DCN
(Document Change Notice).
The Peregrine name, logo, and UTSi are registered trademarks
and UltraCMOS is a trademark of Peregrine Semiconductor
Corp.
©2005 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0149-03 │ UltraCMOS™ RFIC Solutions
Page 8 of 8
相关型号:
©2020 ICPDF网 联系我们和版权申明