QPA9424EVB-01 [QORVO]
High Linearity 0.5 W Small Cell PA;型号: | QPA9424EVB-01 |
厂家: | Qorvo |
描述: | High Linearity 0.5 W Small Cell PA |
文件: | 总10页 (文件大小:1324K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
QPA9424
High Linearity 0.5 W Small Cell PA
®
Product Overview
The QPA9424 is a high-linearity three-stage power
amplifier in a low-cost surface-mount package with on-chip
bias control and temperature control circuits, suitable for
small cell base station applications.
The QPA9424 provides 35.8ꢁdB gain and +27ꢁdBm linear
power over the 2300ꢁ–ꢁ2400ꢁMHz frequency range covering
band 30 and band 40. This amplifier is able to achieve
−48.5ꢁdBc ACLR at +27ꢁdBm output power with 20 MHz
LTE signal.
7ꢀmmꢀxꢀ7ꢀmm Leadless SMT Package
The QPA9424 integrates three high performance amplifier
stages onto a module to allow for a compact system design
and requires very few external components for operation.
The amplifier is bias adjustable allowing the amplifier’s
power consumption to be optimized. The QPA9424 is
available in a 7ꢁxꢁ7ꢁmm surface mount package.
Key Features
• 2.300ꢁ–ꢁ2.400ꢁGHz Frequency Range
• Fully integrated, 3 Stage Power Amplifier
• Internally Matched 50ꢁΩ Input/Output
• −48.5ꢁdBc ACLR at Pavg = +27ꢁdBm
• 35.8ꢁdB Gain
• 14.6% PAE at +27ꢁdBm
• 455ꢁmA Quiescent Current
• On-chip Control Bias and Temp. Comp Circuit
Functional Block Diagram
Applications
• Small Cellꢁ/ꢁPicocell
• Band 30 & Band 40
• Enterprise Femtocell
• Customer Premises Equipment (CPE)
• Data Cards and Terminals
• Distributed Antenna Systems (DAS)
• Booster Amps, Repeaters
Ordering Information
Top View
Part No.
Description
QPA9424TR13
QPA9424EVB-01
2500 pieces on a 13” reel
2300 – 2400 MHz Evaluation board
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
1 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
Absolute Maximum Ratings
Recommended Operating Conditions
Parameter
Rating
Parameter
VCC1, Vcc2
Vref
Min Typ Max Units
Storage Temperature
Supply Voltage (VCC)
Vref
−55 to +150ꢁ°C
+6 V
+3.6 +4.5 +5.25
V
+2.75 +2.85 +2.95
V
TCASE
−40
+85
°C
°C
+3.5 V
RF Input Power, CW, 50Ω, T=25°C
+13 dBm
+196°C
Tj at TCASE max
+156
Electrical specifications are measured at specified test conditions.
Specifications are not guaranteed over all recommended operating
conditions.
Tj at TCASE = 125°C
Operation of this device outside the parameter ranges given
above may cause permanent damage.
Electrical Specifications
Test conditions unless otherwise noted: VCC1 = VCC2 = +4.5ꢁV, Vref = +2.85ꢁV, Temp= +25ꢁ°C
Parameter
Conditions
Min Typ Max Units
Operational Frequency Range
Test Frequency
Gain
Input Return Loss (3)
Output Return Loss (3)
P1dB
2300
2400
MHz
MHz
dB
2350
35.8
20
POUTꢁ+27ꢁdBm,ꢁCW
CW, small signal
CW
32
15
15
38
dB
21.5
35.4
−48.5
−44.8
14.6
455
dB
dBm
dBc
dBc
%
ACLR
POUTꢁ+27ꢁdBm,ꢁ20ꢁMHzꢁLTEꢁE-TM1.1,ꢁ9.5ꢁdB PAR
POUTꢁ+27ꢁdBm,ꢁ20x2ꢁMHzꢁLTEꢁE-TM1.1,ꢁ9.5ꢁdB PAR
POUTꢁ+27ꢁdBm,ꢁ20ꢁMHzꢁLTEꢁE-TM1.1,ꢁ9.5ꢁdB PAR
VCC1 + VCC2
−45
Power Added Efficiency
13
(1)
Quiescent Current, ICQ
330
520
10
mA
µA
Leakage Current on VCC
VCC +4.5V, Vref 0V
1.3
(3)
Reference Current , Iref
Temp -40°C to +85°C, Vref = +2.85V
POUT +27ꢁdBm, 20ꢁMHzꢁLTEꢁE-TM1.1,ꢁ9.5ꢁdB PAR
50% of control signal to 90% of the RF output
50% of control signal to 10% of the RF output
POUT ≤ +27dBm, In & Out of band load VSWR ≤ 10:1
No permanent degradation or failure
2F0 (POUT +27 dBm), CW signal
15
19.5
870
mA
mA
ns
Operational Current, ICC
Wake Up Time (2)
763
1290
670
Power Down Time (2)
Spurious Output Level
VSWR survivability
ns
−60
≥10:1
−45
−56
−65
17.4
dBc
-
−35
−43
dBc
dBc
dBc
°C/W
Harmonics (3)
3F0 (POUT +27 dBm), CW signal
4F0 (POUT +27 dBm), CW signal
Thermal Resistance, θjc
Module (junction to case)
Notes:
1. Vcc1 draws very little current and provides the bias voltage to the current mirror circuit along with Vref to set the bias point for the whole amplifier.
2. Control signal applied to Vref Pin, 0 to 2.85V
3. Guaranteed by design, not tested in production
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
2 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
QPA9424 Application Circuit Schematic and Layout
Bill of Material - QPA9424EVB01
Ref Designation
Value Description
Manufacture Part Number
-
-
Printed Circuit Board
Qorvo
U1
-
Amplifier, High Linearity 0.5 W Power
Resistor, Chip, 0603, 5%
Qorvo
various
various
various
various
various
various
QPA9424
R1
0 Ω
C1
0.01 μF
100 pF
0.1 μF
10 μF
1000 pF
Capacitor, Chip, 0603, 5%
C11
Capacitor, Chip, 0603, 5%
C3, C9
C5, C14
C6, C10
Capacitor, Chip, 0603, 5%
Capacitor, Chip, 6032, 10%, Tantalum
Capacitor, Chip, 0603, 5%, NPO/C0G
QPA9424EVB01 Typical Performances
Test conditions unless otherwise noted: VCC1 = VCC2 = +4.5ꢁV, Vref = +2.85ꢁV, Pout 27dBm, 2350MHz, Signal PAR 9.5dB, Temp= +25ꢁ°C
LTE Signal BW
ACLR1-Low
20MHz
- 48.4
20MHz x 2
- 44.8
Units
dBc
ACLR1-high
- 49.8
- 45.0
dBc
Parameter
Gain
Conditions
-40°C
37.2
+25°C
35.8
+85°C
Units
dB
34.1
-46.8
14.0
ACLR
PAE
POUT = +27 dBm, 20ꢁMHz LTE E-TM1.1, 9.5dB PAR
-49.2
15.2
-48.4
14.6
dBc
%
P1dB
CW
+35.8
+35.4
+34.7
dBm
Test Frequency = 2350MHz
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
3 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
Performance Plots
Test conditions unless otherwise noted: VCC1 = VCC2 = +4.5V, Vref = +2.85ꢁV, LTE signal PAR = 9.5dB, Temp.=ꢁ+25ꢁ°C
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
4 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
Performance Plots (continued)
Test conditions unless otherwise noted: VCC1 = VCC2 = +4.5V, Vref = +2.85ꢁV, LTE signal PAR = 9.5dB, Temp.=ꢁ+25ꢁ°C
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
5 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
Pin Configuration and Description
Pin No.
Label
Description
1
Vref
Provides reference voltage for internal active biasing circuit
2, 3, 6, 8, 9, 10, 13, 14 GND
RF and DC ground.
4
VCC1
RFin
NC
Bias voltage for current mirror in combination with Vref to set the bias point.
RF input pin. The DC is internally blocked at this pin.
No internal connection. Can be left open or grounded for mounting integrity.
Supply to all stages.
5
7
11
12
VCC2
RFout
RF output pin. The DC is internally blocked at this pin.
Backside Paddle
RF/DC GND RF/DC ground. See PCB Mounting Pattern for suggested footprint.
Evaluation Board PCB Information
Qorvo PCB 284717 Material and Stack-up
1 oz. Cu top layer
Nelco N-4000-13
0.014"
1 oz. Cu inner layer
0.062" ± 0.006"
Finished Board
Thickness
Core
1 oz. Cu inner layer
1 oz. Cu bottom layer
Nelco N-4000-13
0.014"
50 Ω line dimensions: width = .028”
spacing = .028”.
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
6 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
Mechanical Information
Package Marking and Dimensions
Marking: Part number – QPA9424
Trace code – Assigned by sub-contractor
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. Dimension and tolerance formats conform to ASME Y14.4M-1994.
3. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012.
PCB Mounting Pattern
Notes:
1. A heat sink underneath the area of the PCB for the mounted device is strictly required for proper thermal operation. Damage to the device can
occur without the use of one.
2. Ground / thermal via holes are critical for the proper performance of this device. Via holes should use a .35mm (#80 / .0135”) diameter drill and
have a final plated thru diameter of .25 mm (.010”).
3. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance.
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
7 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
Tape and Reel Information – Carrier and Cover Tape Dimensions
Feature
Measure
Symbol
Size (in)
0.295
0.295
0.059
0.472
0.079
0.295
0.524
0.630
Size (mm)
7.50
Length
A0
B0
K0
P1
P2
F
Width
7.50
Cavity
Depth
1.50
Pitch
12.0
Cavity to Perforation - Length Direction
2.00
Centerline Distance
Cavity to Perforation - Width Direction
7.50
Cover Tape
Carrier Tape
Width
Width
C
13.3
W
16.0
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
8 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
Tape and Reel Information – Reel Dimensions (13”)
Standard T/R size = 2,500 pieces on a 13” reel.
Feature
Measure
Symbol
Size (in)
12.992
0.874
Size (mm)
330.0
22.2
Diameter
A
W2
W1
N
Flange
Thickness
Space Between Flange
Outer Diameter
Arbor Hole Diameter
Key Slit Width
Key Slit Diameter
0.661
16.8
4.016
102.0
13.0
C
0.512
Hub
B
0.079
2.0
D
0.787
20.0
Tape and Reel Information – Tape Length and Label Placement
Notes:
1. Empty part cavities at the trailing and leading ends are sealed with cover tape. See EIA 481-1-A.
2. Labels are placed on the flange opposite the sprockets in the carrier tape.
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
9 of 10
www.qorvo.com
QPA9424
®
High Linearity 0.5 W Small Cell PA
Handling Precautions
Parameter
Rating
Standard
ESDꢀ–ꢀHuman Body Model (HBM)
Class 1B
ESDAꢁ/ꢁJEDEC JS-001-2012
JEDEC JESD22-C101F
IPC/JEDEC J-STD-020
Caution!
ESD-Sensitive Device
ESDꢀ–ꢀCharged Device Model (CDM) Class C3
MSLꢀ–ꢀMoisture Sensitivity Level
Level 3
Solderability
Compatible with both lead-free (260°C max. reflow temp.) and tin/lead (245°C max. reflow temp.) soldering processes.
Solder profiles available upon request.
Contact plating: Electrolytic plated Au over Ni (Plating thickness: Ni 5.0±30μm, Au 0.10μm minimum)
RoHS Compliance
This part is compliant with the 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment) as amended by Directive 2015/863/EU. This product also has the following attributes:
• Product uses RoHS Exemption 7c-I to meet RoHS Compliance requirements.
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• PFOS Free
• SVHC Free
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.qorvo.com
Tel: 1-844-890-8163
Email: customer.support@qorvo.com
Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for
Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED
HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical,
life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Copyright 2020 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc.
Datasheet Rev. C, October 12, 2020 | Subject to change without notice
10 of 10
www.qorvo.com
相关型号:
©2020 ICPDF网 联系我们和版权申明