QPL9058 [QORVO]
0.5 â 6.0 GHz Ultra Low-Noise LNA;
| 型号： | QPL9058 |
| 厂家： | 
Qorvo |
| 描述： | 0.5 â 6.0 GHz Ultra Low-Noise LNA |
| 文件： | 总13页 (文件大小：1263K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
QPL9058
0.5 – 6.0 GHz Ultra Low-Noise LNA
®
Product Overview
The QPL9058 is a high-linearity, ultra-low noise amplifier in
a small 2 x 2 mm surface-mount package. At 3.6 GHz, the
amplifier typically provides 18 dB gain, +36 dBm OIP3 at a
54 mA bias setting, and 0.6 dB noise figure. The LNA can
be biased from a single positive supply ranging from 3.3 to
5 volts. The device is housed in a green/RoHS-compliant
industry-standard 2x2 mm package.
The QPL9058 is bias adjustable and requires minimal
external components to operate. It also has a power down
control capability integrated into the die for TDD
applications.
8 Pin 2X2 mm DFN Package
Key Features
• 0.5-6.0 GHz Operational Bandwidth
• Low noise figure, 0.6 dB NF @ 3.6 GHz
• 36 dBm OIP3
• 18 dB small signal gain
• Bias adjustable for linearity optimization
• Unconditionally stable
• Shut-down mode pin with 1.8V logic
• Maintains OFF state with high Pin drive
Functional Block Diagram
Applications
• 5G m-MIMO
• Repeaters / DAS
• Mobile Infrastructure
• LTE / WCDMA / CDMA / GSM
• General Purpose Wireless
• TDD or FDD systems
Ordering Information
Top View
Part No.
QPL9058TR7
Description
2500 pieces on a 7” reel
QPL9058EVB-01
0.5-6.0 GHz Evaluation Board
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
1 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Absolute Maximum Ratings
Recommended Operating Conditions
Parameter
Supply Voltage (VDD
TCASE
Min
+3.15
−40
Typ Max Units
Parameter
Rating
-65 to +150°C
+7 V
)
+5
+5.25
+105
+190
V
Storage Temperature
°C
°C
Supply Voltage (VDD
)
Tj for >106 hours MTTF
RF Input Power, CW, 50 Ω, T=25°C
+27 dBm
+22 dBm
Electrical specifications are measured at specified test conditions.
Specifications are not guaranteed over all recommended operating
conditions. Application of conditions to the device outside the
Recommended Operating Conditions may reduce device reliability and
performance.
RF Input Power, LTE 9dB PAR, T=25°C
Exceeding any one or a combination of the Absolute Maximum Rating
conditions may cause permanent damage to the device.
Electrical Specifications
Test conditions unless otherwise noted: VDD=+5ꢀV, Temp.=+25ꢀ°C, 50ꢀΩ system.
Parameter
Conditions
Min
500
Typ
Max
6000
Units
MHz
MHz
dB
Operational Frequency Range
Test Frequency
Gain
3600
18.0
16.5
19.9
0.95
Input Return Loss
Output Return Loss
Noise Figure (1)
Output P1dB
15.0
dB
19.5
dB
0.59
dB
+17.7
+32.0
0
+20.6
+36.4
dBm
dBm
V
Output IP3
Pout=+2 dBm/tone, Δf=1 MHz
On state
0.63
VDD
74
Power Shutdown Control (pin 5)
Current, IDD
Off state (Power down)
On state
1.17
V
54
4
mA
mA
µA
Off state (Power down)
VPD = 1.8 V
7
Shutdown pin current, ISD
Switching Time (LNA On)
Switching Time (LNA Off)
Thermal Resistance
Notes:
18
50% DC to 0.5dB of settled power/gain
50% DC to -20dB from LNA ON power/gain
Channel to case
60
ns
41
ns
63.7
°C/W
1. Input trace loss de-embedded form NF data.
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
2 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
S-Parameters
Test Conditions: VDD=+5 V, IDD=54 mA (typ.), T=+25°C, unmatched 50 Ω system, calibrated to device leads
Freq (GHz) S11 (dB)
S11 (ang)
S21 (dB)
S21 (ang)
S12 (dB)
S12 (ang)
S22 (dB)
S22 (ang)
2
-13.3
-13.8
-14.2
-14.7
-15.1
-15.4
-15.7
-15.9
-16.1
-16.1
-16.0
-15.7
-15.4
-15.0
-14.4
-13.8
-13.3
-12.9
-12.2
-11.3
-10.6
-9.8
-142
-145
-148
-150
-152
-153
-154
-155
-155
-155
-155
-155
-155
-156
-157
-158
-159
-160
-163
-167
-172
-177
177
19.4
19.2
19.0
18.9
18.7
18.6
18.5
18.5
18.4
18.4
18.4
18.4
18.5
18.5
18.6
18.7
18.8
18.9
19.0
19.1
19.2
19.3
19.3
19.3
19.3
19.2
19.1
18.9
18.7
18.4
18.1
13
8
2
-4
-9
-29.8
-29.7
-29.6
-29.5
-29.5
-29.5
-29.5
-29.5
-29.5
-29.5
-29.5
-29.6
-29.6
-29.7
-29.8
-29.8
-29.9
-30.0
-30.1
-30.3
-30.4
-30.6
-30.8
-31.1
-31.4
-31.8
-32.2
-32.6
-33.1
-33.6
-34.1
-17
-20
-23
-26
-29
-33
-36
-40
-43
-47
-51
-55
-59
-63
-67
-72
-77
-22.9
-23.3
-23.4
-23.5
-23.5
-23.4
-23.4
-23.3
-23.4
-23.6
-24.1
-24.6
-25.6
-26.9
-29.2
-32.2
-36.5
-45.1
-33.3
-26.4
-22.4
-19.2
-16.7
-14.5
-12.8
-11.2
-9.9
-21
-17
-12
-8
-4
-2
1
1
2
1
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
-15
-20
-26
-32
-37
-43
-49
-55
-61
-67
-73
-79
-86
-92
-99
-106
-114
-122
-130
-138
-146
-154
-162
-170
-178
174
1
-1
-4
-9
-17
-34
-61
-87
-168
175
168
162
155
150
143
137
130
125
118
113
107
-82
-87
-93
-99
-105
-112
-119
-126
-134
-142
-149
-157
-165
-173
-9.1
-8.5
-7.9
-7.4
-6.9
-6.6
-6.3
-6.1
171
165
159
152
146
140
133
127
-8.8
-7.8
-7.0
-6.3
-6.0
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
3 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Noise Parameters
Test Conditions: VDD=+5 V, IDD=54 mA (typ.), T=+25°C, unmatched 50 ohm system, calibrated to device leads
Freq (GHz)
NFmin (dB)
GammaOpt (mag)
GammaOpt (deg)
rn (Ω)
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
0.22
0.26
0.29
0.28
0.34
0.36
0.37
0.39
0.43
0.39
0.49
0.42
0.49
0.47
0.46
0.60
0.54
0.52
0.55
0.52
0.55
0.54
0.57
0.58
0.59
0.59
0.56
0.58
0.55
0.56
0.58
0.14
0.08
0.12
0.10
0.08
0.06
0.12
0.11
0.10
0.14
0.06
0.14
0.14
0.19
0.22
0.08
0.19
0.20
0.11
0.17
0.18
0.16
0.16
0.16
0.17
0.20
0.17
0.16
0.18
0.16
0.16
66
81
72
90
83
0.048
0.048
0.047
0.048
0.052
0.053
0.046
0.049
0.052
0.046
0.062
0.049
0.052
0.046
0.040
0.065
0.050
0.050
0.051
0.055
0.052
0.055
0.055
0.050
0.051
0.052
0.046
0.045
0.047
0.048
0.050
111
104
110
116
121
150
127
125
127
139
148
131
133
-123
135
147
154
165
161
156
-168
180
-179
178
-171
-168
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
4 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Evaluation Board – QPL9058EVB-01
Notes:
1. See Evaluation Board PCB Information section for material and stack-up.
2. All components are of 0402 size unless otherwise mentioned.
3. For TDD Applications: R1 = 0Ω and R2 = 220K.
4. For FDD Applications: R2 = 220K ‘OR’ Pin 5 tied to ground. R1 = DNP/Omitted
5. A through line is included on the evaluation board to de-embed the board losses.
6. R4 sets the current draw. Can be changed for the desired bias point.
Bill of Material – QPL9058EVB-01
Reference Des.
Value
Description
Manuf.
Part Number
N/A
N/A
Printed Circuit Board
Qorvo
U1
n/a
0 Ω
Ultra Low Noise QPL9058 LNA
Resistor, chip, 0402, 1%, 1/10W
Resistor, chip, 0402, 5%, 1/16W
Qorvo
various
various
various
Murata
Murata
various
Coilcraft
QPL9058
R1, R3
R2
220 KΩ
R4
3.83 KΩ Resistor, Chip, 0402, 1%, 1/16W
15 pF Cap., Chip, 0402, 2%, 50V, HI-Q
1000 pF Cap., Chip, 0402, 10%, 50V, X7R
C1, C2, C6, C7
GJM1555C1H150JB01D
GRM155R71H102KA01D
C3. C5
C4
0.1 uF
18 nH
Cap., Chip, 0402, 10%, 50V, X5R
Inductor, coil, 0603, 5%
L1
0603CS-18NXJL
R4 Resistor values for various IDD settings
IDD (mA)
R4
40
45
50
55
60
65
70
75
VDD = 5 V
5.75K
2.9K
4.8K
2.4K
4.1K
2.05K
3.7K
1.75K
3.12K
1.53K
2.8K
2.5K
1.2K
2.27K
1.05K
R4
VDD = 3.3 V
1.33K
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
5 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Typical Performance – QPL9058EVB-01
Test conditions unless otherwise noted: VDD = +5 V, IDD = 54 mA (typ.), Temp = +25°C
Typical Values
Units
MHz
dB
Parameter
Frequency
Conditions
2500
18.2
14.3
23.1
20.6
32.6
0.47
3600
18.0
14.7
20.0
20.5
36.0
0.62
4900
18.9
9.8
Gain
Input Return Loss
Output Return Loss
Output P1dB
OIP3
dB
13.5
16.6
33.9
0.56
dB
dBm
dBm
dB
Pout=+2 dBm/tone, ∆f=1 MHz
Noise figure (1)
Note:
1. Input trace loss de-embedded from NF data
Performance Plots – QPL9058EVB-01
Test conditions unless otherwise noted: VDD = +5 V, IDD = 54 mA, 50ꢀΩ system
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
6 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Performance Plots – QPL9058EVB-01 Continued
Test conditions unless otherwise noted: VDD = +5 V, IDD = 54 mA, 50ꢀΩ system
Notes:
1. Input trace loss de-embedded from NF. NF at cold temp is better than 0.3dB causing measurement uncertainties. Therefore, not shown on the
plot
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
7 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Typical Performance – QPL9058EVB-01
Test conditions unless otherwise noted: VDD = +3.3 V, IDD = 50 mA, Temp = +25°C
Typical Values
Units
MHz
dB
Parameter
Frequency
Conditions
2500
17.6
14.1
18.0
15.8
32.3
0.48
3500
17.4
16.6
15.2
17.6
33.0
0.59
5000
18.0
8.6
Gain
Input Return Loss
Output Return Loss
Output P1dB
OIP3
dB
12.2
13.8
32.8
0.56
dB
dBm
dBm
dB
Pout=+0 dBm/tone, ∆f=1 MHz
Noise figure (1)
Notes:
1. Input trace loss de-embedded from NF data
Performance Plots – QPL9058EVB-01
Test conditions unless otherwise noted: VDD = +3.3 V, IDD = 50 mA, Temp = +25°C, 50ꢀΩ system
Note:
1. Input trace loss de-embedded from NF data.
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
8 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Pad Configuration and Description
Top View
Pad No.
Label
Vbias
Description
Sets the LNA bias current for the device.
1
2
RF In
RF Input pin, internally matched to 50 ohms. A DC block is required.
A high voltage (>1.17V) turns off the device. If the pin is pulled to ground or driven with a
voltage less than 0.63V, then the device will operate under LNA ON state.
5
Shut Down
7
RF Out
NC
RF Output pin, internally matched to 50 ohms. A DC block is required. VDD supply pin.
Not connected internally. This pin may be left floating or connected to ground.
3, 4, 6, 8
Ground connection. The back side of the package should be connected to the ground
plan though as short of a connection as possible. PCB vias under the device are
recommended.
Backside Paddle
RF/DC GND
Evaluation Board PCB Information
Qorvo PCB Material and Stack-up
1 oz. Cu top layer
Rogers 4003C
0.008"
εr=3.5 typ.
1 oz. Cu inner layer
0.062" ± 0.006"
Finished Board
Thickness
FR4
FR4
1 oz. Cu inner layer
1 oz. Cu bottom layer
0.008"
50 ohm line dimensions: width = 0.0182”, spacing = 0.020”
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
9 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Package Marking and Dimensions
Marking: Part Number – 9058
Trace Code –ꢁXXXX up to 4 Characters assigned by sub-contractor
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. The terminal #1 identifier and terminal numbering conform to SPE-000677.
3. Contact plating: NiPdAu
Recommended PCB Layout Pattern
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. Use 1 oz. copper minimum for top and bottom layer metal.
3. Via holes are required under the backside paddle of this device for proper RF/DC grounding and thermal dissipation. We recommend a 0.35mm
(#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.01”).
4. Ensure good package backside paddle solder attach for reliable operation and best electrical performance.
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
10 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Tape and Reel Information – Carrier and Cover Tape Dimensions
Feature
Measure
Symbol
Size (in)
0.091
0.091
0.039
0.157
0.079
0.138
0.213
0.315
Size (mm)
2.30
Length
A0
B0
K0
P1
P2
F
Width
2.30
Cavity
Depth
1.00
Pitch
4.00
Cavity to Perforation - Length Direction
2.00
Centerline Distance
Cavity to Perforation - Width Direction
3.50
Cover Tape
Carrier Tape
Width
Width
C
5.40
W
8.00
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
11 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Tape and Reel Information – Reel Dimensions
Standard T/R size = 2500 pieces on a 7” reel.
Feature
Measure
Diameter
Symbol
Size (in)
6.969
Size (mm)
177.0
A
Flange
Thickness
W2
0.559
14.2
Space Between Flange
Outer Diameter
W1
N
0.346
2.283
0.512
0.079
0.787
8.8
58.0
13.0
2.0
Arbor Hole Diameter
Key Slit Width
C
Hub
B
Key Slit Diameter
D
20.0
Tape and Reel Information – Tape Length and Label Placement
Notes:
1. Empty part cavities at the trailing and leading ends are sealed with cover tape. See EIA 481-1-A.
2. Labels are placed on the flange opposite the sprockets in the carrier tape.
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
12 of 13
www.qorvo.com
QPL9058
®
0.5 – 6.0 GHz Ultra Low-Noise LNA
Handling Precautions
Parameter
Rating
Standard
ESDꢁ–ꢁHuman Body Model (HBM)
ESDꢁ–ꢁCharged Device Model (CDM)
MSLꢁ–ꢁMoisture Sensitivity Level
Class 1B ESDAꢀ/ꢀJEDEC JS-001-2017
Caution!
ESD-Sensitive Device
Class C3 JEDEC JESD22-C101F
Level 1
IPC/JEDEC J-STD-020E
Solderability
Compatible with both lead-free (260°C max. reflow temperature) and tin/lead (245°C max. reflow temperature) soldering processes.
Solder profiles available upon request.
Contact plating: NiPdAu (Thickness: Ni 0.508 ~1.524 μm; Pd 0.023 ~ 0.1016 μm; Au 0.00254 ~ 0.01016 μm)
RoHS Compliance
This part is compliant with 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment) as amended by Directive 2015/863/EU.
This product also has the following attributes:
• Lead Free
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• PFOS Free
• SVHC Free
Pb
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.qorvo.com
Tel: 1-844-890-8163
Email: customer.support@qorvo.com
Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for
Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED
HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical,
life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Copyright 2020 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc.
Data Sheet, Rev. D, November 18, 2020 | Subject to change without notice
13 of 13
www.qorvo.com
相关型号：
©2020 ICPDF网 联系我们和版权申明