QPQ1063EVB01 [QORVO]
L1/L2 Low Loss GPS SAW Diplexer;型号: | QPQ1063EVB01 |
厂家: | Qorvo |
描述: | L1/L2 Low Loss GPS SAW Diplexer 全球定位系统 |
文件: | 总10页 (文件大小:524K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
General Description
QPQ1063 is a L1/L2 GPS diplexer in a compact size for
use in any GPS application. Designed for rejection of
unwanted GPS signals, this SAW diplexer also has
excellent power handling capability for low power
transmitters.
Housed in a 5.0 x 5.0 mm laminate with overmold
package, this device allows for a compact and cost-
effective diplexer solution for GPS applications.
5.0 X 5.0 X 0.84 mm
No matching components are required, making the PCB
design and implementation easy.
Product Features
•
Usable Bandwidth 21 MHz for each Band
•
•
•
•
•
No matching required for operation at 50Ω
Excellent rejection for GPS operation
Functional Block Diagram
High Isolation
High Rejection
Laminate with Overmold Surface Mount Package
(SMP)
•
Small Size: 5.0 x 5.0 x 0.84mm
Performance is typical across frequency. Please
reference electrical specification table and data plots
for more details.
Applications
Top View
• General purpose GPS
• Communication Systems
Pin Configuration - Single Ended
Pin No.
Label
1
Antenna, Common Port
L1 Band Output Port
L2 Band Output Port
Ground connection
2
3
Ordering Information
Pkg Base
Part No.
QPQ1063TR7
Description
7” Taped Reel with 1000 pieces
Blocking capacitors are required on any ports where a DC voltage may
be present.
QPQ1063EVB01
Evaluation board
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
1 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
Absolute Maximum Ratings
Minimum Lifetime Ratings
Parameter
Rating
Conditions
Rating
Storage Temperature
Operation Temperature
-55 to +105°C
-55 to +85°C
RF Input Power +25dBm, CW
@ Pin 1 (Antenna Port), Pin 2 (L1 Port)
or Pin 3 (L2 Port)
>10 years @ +95°C
>5 years @ +105°C
RF Input Power on L1 Port or L2 Port
with another port terminated
+33 dBm
PW = 200ms; DC = 50% @ +25ꢁ°C
Exceeding any one or a combination of the Absolute Maximum Rating
conditions may cause permanent damage to the device. Extended
application of Absolute Maximum Rating conditions to the device may
reduce device reliability.
Electrical Specifications - L1 GPS Frequency Band
Test conditions unless otherwise noted: Temperature Rangeꢀ=ꢀ-55ꢀ°C to +85ꢀ°C, 50ꢀΩ system
Parameter (3)
Center Frequency
Conditions (1) (2)
Min
-
Typical (4)
Max Units
1575.42
1.5
1.6
0.1
0.2
4
-
2
MHz
1574.397 - 1576.443 MHz
1565.19 - 1585.65 MHz
1574.397 - 1576.443 MHz
1565.19 - 1585.65 MHz
1574.397 - 1576.443 MHz
1565.19 - 1585.65 MHz
824 - 960 MHz
-
Maximum Insertion Loss
Amplitude Variation
dB
-
2.1
0.4
0.7
14
18
-
-
dB
ns
-
-
Group Delay Variation
-
7
43
29
28
26
30
40
10
10
-
51
1500ꢀ-ꢀ1520 MHz
34
-
1520ꢀ-ꢀ1525.42 MHz
1625.42 – 1630 MHz
1630 – 1650 MHz
32
-
Absolute Attenuation
(Relative to 0 dB)
dB
45
-
54
-
1710 - 2170 MHz
48
-
1574.397 - 1576.443 MHz
1565.19 - 1585.65 MHz
Single Ended
18
-
Return Loss at Port 2
dB
18
-
Nominal Impedance (5)
Notes:
50
-
Ω
1. All specifications are based on the Qorvo schematics for the reference designs shown on page 4.
2. In production, devices will be tested at room temperature to a guard banded specification to ensure electrical compliance over temperature.
3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacture tolerances.
4. Typical values are based on average measurements at room temperature on PCB (+25ꢀ°C ±5ꢀ°C)
5. Optimum impedance to achieve the performance shown
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
2 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
Electrical Specifications – L2 GPS Frequency Band
Test conditions unless otherwise noted: Temperature Rangeꢀ=ꢀ-55ꢀ°C to +85ꢀ°C, 50ꢀΩ system
Parameter (3)
Conditions (1) (2)
Min
-
Typical (4)
Max Units
Center Frequency
1227.6
1.2
1.3
0.1
0.2
3
-
MHz
1226.577 - 1228.623 MHz
1217.370 - 1237.830 MHz
1226.577 - 1228.623 MHz
1217.370 - 1237.830 MHz
1226.577 - 1228.623 MHz
1217.370 - 1237.830 MHz
464 - 600 MHz
-
1.6
1.7
0.4
0.5
15
22
-
Maximum Insertion Loss
Amplitude Variation
dB
dB
ns
-
-
-
-
Group Delay Variation
-
7
37
40
40
39
10
10
-
40
1150 - 1177.6 MHz
48
-
Absolute Attenuation, Relative to 0 dB
dB
1277.6ꢀ- 1300 MHz
49
1360 - 1820 MHz
46
-
-
-
-
1226.577 - 1228.623 MHz
1217.370 - 1237.830 MHz
Single Ended
24
Return Loss at Port 3
Nominal Impedance (5)
dB
24
50
Ω
Electrical Specifications – L1 & L2 GPS Frequency Bands
Test conditions unless otherwise noted: Temperature Rangeꢀ=ꢀ-55ꢀ°C to +85ꢀ°C, 50ꢀΩ system
Parameter (3)
Nominal Impedance (5)
Conditions (1) (2)
Single Ended
Min
-
Typical (4)
Max Units
50
19
19
24
18
53
48
58
48
-
-
-
-
-
-
-
-
-
Ω
1574.397 - 1576.443 MHz
1565.19ꢀ–ꢀ1585.65 MHz
1226.577 - 1228.623 MHz
1217.370 - 1237.830 MHz
1574.397 - 1576.443 MHz
1565.19ꢀ–ꢀ1585.65 MHz
1226.577 - 1228.623 MHz
1217.370 - 1237.830 MHz
11
11
11
11
41
39
47
45
Antenna Return Loss
dB
dB
Isolation
Notes:
1. All specifications are based on the Qorvo schematics for the reference designs shown on page 4.
2. In production, devices will be tested at room temperature to a guard banded specification to ensure electrical compliance over temperature.
3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacture tolerances.
4. Typical values are based on average measurements at room temperature on PCB (+25ꢀ°C ±5ꢀ°C)
5. Optimum impedance to achieve the performance shown.
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
3 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
Evaluation Board – QPQ1063EVB01
Notes:
1. Blocking capacitors are required on any RF ports where a DC voltage may be present.
2. The back side of the package should be connected to the ground plan. Multiple vias should be used on PCB under the device are recommended.
Bill of Material – QPQ1063EVB01
Reference Des.
Value
Description
Manuf.
Qorvo
Part Number
DUT
SMA
PCB
-
-
-
L1/L2 Low Loss GPS SAW Diplexer
SMA connector
QPQ1063
Various
Various
Printed Circuit Board
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
4 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
L1 Band Typical Performance Plots
Test conditions unless otherwise noted: Tempꢀ=ꢀ+25ꢀ°C, 50ꢀΩ system
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
5 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
L2 Band Typical Performance Plots
Test conditions unless otherwise noted: Tempꢀ=ꢀ+25ꢀ°C, 50ꢀΩ system
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
6 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
L1 - L2 Band Typical Performance Plots
Test conditions unless otherwise noted: Tempꢀ=ꢀ+25ꢀ°C, 50ꢀΩ system
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
7 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
Package Marking and Dimensions
Marking: Qorvo Logo
Part Number – 1063
Trace Code –ꢀ Assigned by subcontractor
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012
PCB Mounting Pattern
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
.
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
8 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
Assembly Notes
Compatible with both Lead-free solder (260°C peak reflow temperature) and tin/lead (245°C peak reflow temp.) soldering
processes.
Contact plating: ENEPIG
Recommended Soldering Profile
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
9 of 10
www.qorvo.com
QPQ1063
L1/L2 Low Loss GPS SAW Diplexer
®
Handling Precautions
Parameter
Rating
Standard
ESDꢀ–ꢀHuman Body Model (HBM)
ESDꢀ–ꢀCharged Device Model (CDM)
MSLꢀ–ꢀMoisture Sensitivity Level
Class 1A ESDAꢁ/ꢁJEDEC JS-001
Class C3 ESDAꢁ/ꢁJEDEC JS-002
Caution!
ESD-Sensitive Device
Level 3
IPC/JEDEC J-STD-020
RoHS Compliance
This part is compliant with 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment) as amended by Directive 2015/863/EU.
This product also has the following attributes:
• Lead Free
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• SVHC Free
• PFOS Free
Pb
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.qorvo.com
Tel: 1-844-890-8163
Email: customer.support@qorvo.com
Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for
Qorvo products. The information contained herein, or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED
HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical,
lifesaving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Copyright 2021 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc.
Data Sheet Rev A, June 25, 2021 | Subject to change without notice
10 of 10
www.qorvo.com
相关型号:
©2020 ICPDF网 联系我们和版权申明