PLC-040S105D [QUALTEK]

40Watts Single Output LED Driver; 40Watts单路输出LED驱动器


型号：	PLC-040S105D
厂家：	QUALTEK ELECTRONICS CORPORATION
描述：	40Watts Single Output LED Driver 40Watts单路输出LED驱动器驱动器
文件：	总3页 (文件大小：1618K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ualtek

P C

40Watts Single Output LED Driver

PLC-040 D Series

Electronics Corporation

Features:

Constant Current Design

Dimming Control

Universal AC input/ Full Range

Built-in Active PFC function, PF 0.95 Typical

High Efficiency (Up to 88%)

Output Protections: OVP/SCP/OTP

Lightning Protection

Class 2 Power Unit (See Note)

Waterproof (IP65)

3 Year Warranty

PLC-040S035D PLC-040S045D PLC-040S070D PLC-040S105D PLC-040S128D PLC-040S140D`PLC-040S166D PLC-040S222D PLC-040S333D

Model

Output Characteristics

0.35A (1)

38~114V

±10% Vo

±5% Vo

±1% Vo

±5% Vo

0.45A (1)

30~89V

0.70A (2)

18~54V

1.05A ⁽³⁾

12~36V

1.28A ⁽³⁾

10~29V

1.40A ⁽³⁾

10~25V

1.66A ⁽³⁾

8~23V

2.22A (3)

6~16V

3.33A (3)

4~11V

Rated Current

Voltage Range

See Note

Ripple and Noise (max) Note 1

Voltage Accuracy

Line Regulation

Load Regulation

20mS Max @ Rated Load

Rise Time

8.5mS Min (110VAC input, full load), 10mS Min (220VAC input, full load)

Hold-up Time (Typ.)

Input Characteristics

Voltage Range

90VAC~305VAC

47Hz-63Hz

Frequency Range

>0.95

>0.90

88%

>0.95

>0.90

88%

>0.95

>0.90

87%

>0.95

>0.90

87%

>0.95

>0.90

87%

>0.95

>0.90

87%

>0.95

>0.90

86%

>0.95

>0.90

85%

>0.95

>0.90

84%

Power Factor

(Typical)

110VAC

220VAC

Efficiency (Typical)

AC Current (max)

Inrush Current (max)

Leakage Current

0.6A @ 100-277VAC Input Full Load

65A @ 230VAC, 25°C

0.5mA max @ 277VAC

Protection

110°C (Temperature of internal components); shut down, auto recover after the temperature decreases

Over Temperature (OTP)

1.2~1.7Vo

Over Voltage (OVP)

Short Circuit (SCP)

Note 2

Long-term mode, auto recovery

Environmental Characteristics

Operating Temperature

Operating Relative Humidity

Storage Temperature

Vibration

-35°C~70°C

5% RH to 95% RH

-40°C~85°C, 5% to 100% RH non-condensing

10 to 300Hz sweep at constant acceleration of 1.0G(Breadth: 3.5mm) for 1 Hour for each of the perpendicular axes X, Y, Z

IP65

Waterproof Rating

Safety Standards

Withstand Voltage

Isolation Resistance

EMC Emission

UL8750, Compliance to UL1012 UL935, IEC61347

L/N-GND: 4kV, L-N: 2kV

I/P-O/P: >100M Ohms / 500VDC / 25°C / 70% RH

Compliance to EN55022(CISPR22) Class B, EN61000-3-2 Class A, EN61000-3-3

Compliance to EN61000-3-2, 3 EN61000-4-2, 3, 4, 5, 6, 8, 11, EN61547

EMC Immunity

Characteristics

Life Time

More than 78,000Hrs (25°C, 80% Load)

MTBF (MIL-HDBK-217F)

Dimension (LxWxH)

Note

More than 492,000Hrs (25°C, 80% Load)

95x70x32mm

1. Ripple & Noise: Measured by 20 MHz bandwidth oscilloscope and the output paralleled with a 0.1 uF ceramic capacitor and a 10 uF electrolytic capacitor.

2. Latch Mode: The power supply shall return to normal operation only after the power is turned on again

(1) Non-Class 2 output (USR & CNR)

(2) Class 2 output (USR); Non-Class 2 output (CNR)

(3) Class 2 output (USR & CNR)

Page 1 of 3

ualtek

P C

40Watts Single Output LED Driver

PLC-040 D Series

Electronics Corporation

DIMMING CONTROL

The dimmer control may be operated from either a potentiometer or from an input

signal of 1 – 10 Vdc. Two recommended implementations are provided below.

1-10V

INPUT (PURPLE)

10V OUTPUT

(YELLOW)

1-10V

INPUT(PURPLE)

1-10Vdc

20K

PLC-040SXXXD

GND(GREEN)

Implementation 1: DC Input

Implementation 2: Potentiometer Control

Io/Ir Vs Vdim

100%

80%

60%

40%

20%

10 11

Vdim(V)

Notes:

1. Io is actual output current and Ir is rated current.

2. If the dimming function is not used, please short 10 V output pin (yellow) and 1-10 V input pin(purple).

The output current is about 92% Ir when the 1-10V input pin is ꢀoating.

3. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold

(approx. 50% of the max. output voltage for any given model).

4. The dimming voltage can be tuned down to less than 1V, and the output current will be decreased to about

10% Ir; but the connected LEDs may ꢀicker. Keeping dimming voltage greater than 1V is strongly recommended.

5. Do not connect the GND of dimming to the output; otherwise, the LED driver will not work normally.

www.qualtekusa.com

ISO-9001 Company

Page 2 of 3

ualtek

P C

40Watts Single Output LED Driver

PLC-040 D Series

Electronics Corporation

UNIT: mm

MECHANICAL SPECIFICATIONS

Derating Curve

Ambient Temperature vs.Load

100

120

150

180

210

240

270

300

330

-35

-20

-5

Ambient Temperature(°C)

Input Voltage(V)

www.qualtekusa.com

Rev. B

ISO-9001 Company

Page 3 of 3

相关型号：