FC0805-6R2-JBW [RCD]

Fixed Resistor - Fusible, 0.15W, 6.2ohm, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0805, CHIP, ROHS COMPLIANT;


型号：	FC0805-6R2-JBW
厂家：	RCD COMPONENTS INC.
描述：	Fixed Resistor - Fusible, 0.15W, 6.2ohm, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0805, CHIP, ROHS COMPLIANT CD 电阻器
文件：	总1页 (文件大小：25K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

RESISTORSꢀCAPACITORSꢀCOILSꢀDELAY LINES

FUSIBLE CHIP RESISTORS

Term.W is

RoHS

compliant

& 260°C

compatible

RoHS

FC SERIES

ꢀ Industry’s broadest range of fusible chip resistors-

7 standard sizes from 0402 to 2512, widest resistance

range- 1Ω to 10K standard

ꢀ Perform like conventional chip resistors under normal

conditions but fuse when subject to overloads

ꢀ Standard tolerance: ±5%,10% (1%,2% available)

ꢀ See MBW Series for additional SM fuse resistors (1/4W-3W)

Surface Mount Circuit Protection!

RCD Series FC resistors offer a low cost approach to circuit

protection in case of overload or component failure. The resistor

is designed to act as a conventional resistor under normal

operating conditions, but will quickly open when subjected to

suitable continuous overload. Standard fusing characteristics

can be altered to customer requirements.

OPTIONS

ꢀ Option ER: Group A screening per Mil-PRF-55342

ꢀ Customized fusing time and/or fusing power level

RCD Wattage Max. Hold-Off Resistance

DIMENSIONS

Type

Rating

Voltage

Range

FC0402 .10W

FC0603 .125W

FC0805 .15W

FC1206 .25W

50V¹

1Ω to 1KΩ²

.040± .004 [1.0±.10] .020 ± .002 [0.5 ± .05] .014 ± .004 [.35 ± .15] .010 ± .005 [.25 ± .12]

100V¹

150V¹

200V¹

1Ω to 1.8KΩ².063 ± .008 [1.6 ± .20] .031 ± .005 [0.8 ± .13] .018 ± .006 [.45 ± .15] .012 ± .008 [.30 ± .20]

1Ω to 3KΩ².079 ± .008 [2.0 ± .20] .050 ± .006 [1.25 ± .15] .018 ± .006 [.45 ± .15] .014 ± .008 [.35 ± .20]

1Ω to 5.1KΩ².126 ± .008 [3.2 ± .20] .063 ± .008 [1.6 ± .20] .020 ± .006 [.50 ± .15] .020 ± .010 [.51 ± .25]

FC1210 .50W

FC2010 .75W

FC2512 1.0W

250V¹

300V¹

400V¹

1Ω to 6.2KΩ².126 ± .008 [3.2 ± .20] .098 ± .008 [2.5 ± .20] .024 ± .008 [.61 ± .20] .020 ± .010 [.51 ± .25]

1Ω to 7.5KΩ².197 ± .008 [5.0 ± .20] .100 ± .008 [2.6 ± .20] .024 ± .008 [.61 ±. 20] .020 ± .010 [.51 ± .25]

1Ω to 10KΩ².248 ± .008 [6.3 ± .20] .124 ± .010 [3.2 ± .25] .024 ± .008 [.61 ± .20] .030 ± .018 [.75 ± .46]

¹Open circuit voltage (consult factory for increased voltage rating) ²Extended resistance range available

TYPICAL PERFORMANCE CHARACTERISTICS

REQUIREMENTS

CHARACTERISTICS

TEST METHOD

Min. Fusing Power

FC0402: <30 sec at 2.5W

FC0603: <30 sec at 3W

FC0805: <30 sec at 3.25W

FC1206: <30 sec at 5W

FC1210: <30 sec at 7.5W

FC2010: <30 sec at 11.25W

FC2512: <30 sec at 15W

Unmounted, 25°C, residual resistance

to be a minimum of 100X the original

value.

CONSTRUCTION

Environmental Seal

Fusible Resistive film

Marking available

(specify Opt. A)

Temperature Coefficient

200ppm/°C (<5Ω=250ppm) 25°C to +125°C

Resistance to Soldering Heat

High Temperature Exposure

Low Temp. Operation

Moisture Resistance

Load Life (1000 hours)

Thermal Shock

± 0.25%

± 0.5%

± 1.5%

± 5%

260 ± 5°C, 3 seconds

100 hours @ +125°C

-55°C, 1 hour

Mil-PRF-55342

Rated W per Mil-PRF-55342 4.8.11.1

-55°C to +125°C, 0.5 hours, 5 cycles

MIL-Std-202, Method 208

Alumina

Substrate

Inner Electrode

Nickel Barrier

± 0.5%

95% (Min.)

Solder Plating

Solderability

Dielectric Withstanding Voltage 250V (100V 0402 & 0603) 60 Seconds, terminal to ceramic

Operating Temp. Range

Derating (above 70°C)

-55°C to +125°C

derate W & V by 1.18%/°C

APPLICATION NOTES:

P/N DESIGNATION:

FC1206

102 -

T W

Fault level must be suitable to safely open the resistor. If insufficient

the resistor may reach elevated temp. For this reason, the fusing load

must be relatively large compared to rated W, 30-60x is common for

most circuits, and should be at least equal to the minimum fusing

power listed in Performance Chart. Fusing may still occur at W levels

below these but not as consistently (fast-blow models available).

Don’t exceed volt rating or 200x W rating, whichever is less. Customers

should evaluate product for suitability under all possible overload

scenarios. Customized fusing characteristics are available.

Fusing times vary depending on the amount of “heat sinking”

involved, i.e. PCB material, pad size, trace thickness, etc.

Customers should evaluate fusing in actual-use conditions.

RCD Type

Option Codes: ER, A, etc.

(leave blank if standard)

Resis.Code 1%: 3 signif. figures & multiplier

(1R00=1Ω, 10R0=10Ω, 1000=100Ω, 1001=1K, 1002=10K)

Resis.Code 2%-10%: 2 signif. figures & multiplier,

(1R0=1Ω, 100=10Ω, 101=100Ω, 102=1K, 103=10K)

Tolerance Code: F= 1%, J= 5%, K=10%

Packaging: B = Bulk, T = Tape & Reel

Termination: W= Lead-free, Q= Tin/Lead (leave blank if either is

acceptable, in which case RCD will select based on lowest price

and quickest delivery)

Exercise care when testing fuse resistors.

RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603 669 0054 Fax: 603 669 5455 Email:sales@rcdcomponents.com

FA021C Sale of this product is in accordance with GF-061. Specifications subject to change without notice.

相关型号：