RACV06-12-LP [RECOM]

Terminal Block Input/Output with Cable Clamps;


型号：	RACV06-12-LP
厂家：	RECOM INTERNATIONAL POWER
描述：	Terminal Block Input/Output with Cable Clamps
文件：	总4页 (文件大小：464K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

• Low Proﬁle Case (11mm height max.)

• 12V and 24V Constant Voltage Outputs

• Terminal Block Input/Output with Cable Clamps

• Fully Protected (OLP, SCP, OCP, OTP)

• low Standby Power, ErP conform

• low cost

Features

AC/DC Converter

LED

Driver

RACV06-LP

6 Watt

Constant

Description

These low proﬁle constant voltage LED drivers have been designed for cost-sensitive applications.

The SELV outputs are suitable for both independently supplied or built-in power-supply LED luminaires.

Their low proﬁle design allows them to be invisibly built into furniture, discreetly ounted under shelves

or integrated in space-restricted applications such as coving lighting, strip lighting or troffer lighting sys-

tems. The power supplies are short circuit and overload protected and come with a full 3-year warranty.

Voltage Single

Output

Selection Guide

Part

Number

nom. Input

Voltage

[VAC]

Input

Current

[mA]

Output

Voltage

[VDC]

Output

Current Range

[mA]

Efﬁciency Output

typ. Power max.

[%]

[W]

RACV06-12-LP

RACV06-24-LP

230

0-500

0-250

All LED Drivers may not be used without a load. They must be switched on the primary side only.

Noncompliance may damage the LED or reduce its lifetime.

Speciﬁcations (measured @ ta= 25°C, 240VAC and rated load)

BASIC CHARACTERISTICS

Parameter

Input Voltage Range

Inrush Current

Condition

Min.

198VAC

Typ.

230VAC

Max.

264VAC

7.0A

ERP

compliant

Start-up Time

50ms

63Hz

Input Frequency Range

No Load Power Consumption

Power Factor

47Hz

0.3W

full load, 230VAC

full load

0.55

Internal Operating Frequency

65kHz

140kHz

IEC/EN61347-1 Certiﬁed

IEC/EN61347-2-13 Certiﬁed

ENEC Certiﬁed

12Vout

24Vout

500mVp-p

250mVp-p

Output Ripple Voltage ⁽¹⁾

CB Report

Notes:

EN55015 Compliant

Note1: Measured at 20MHz BW using 0.1µF & 47µF parallel capacitor.

REGULATIONS

Parameter

Condition

Value

Output Voltage Accuracy

Line Regulation

5ꢀ maꢁ.

3ꢀ maꢁ.

Load Regulation

www.recom-power.com

REV.: 0/2016

L-1

RACV06-LP

AC/DC Converter

Speciﬁcations (measured @ ta= 25°C, 240VAC and rated load)

Series

PROTECTION

Parameter

Condition

Value

Input Fuse

eꢁternal fuse is recommended

T1A

Open Circuit Protection (OCP)

Over Load Protection (OLP)

Over Voltage Protection (OVP)

Over Temperature Protection (OTP)

Isolation Voltage

auto recovery after fault condition is removed

3.75kVAC / 1 minute

110°C Tcase

I/P to O/P

Maximum loading of automatic circuit breakers

@ 230VAC, 1Ohm, 90° phase angle and max. load

Circuit Breaker

Circuit Breaker Current

Typ

10A

16A

20A

25A

115

ENVIRONMENTAL

Parameter

Condition

Value

Operating Temperature Range

Maꢁimum Case Temperature

Operating Altitude

Operating Humidity

IP Rating

-20°C to +50°C, Ambient

+80°C

2000m

5ꢀ to 85ꢀ RH, non condensing

IP20

PD2

Pollution Degree

Design Lifetime

30 ꢁ 10³ hours

Derating Graph

100

-20 -10

20 30

50 60

Ambient Temperature [°C]

SAFETY AND CERTIFICATIONS

Certiﬁcate Type

Report Number

Standard

IEC61347-1, 2nd Edition, 2012

EN61347-1, 2nd Edition 2013

Lamp Controlgear General Requirments for Safety

305987

305985

IEC61347-2-13, 2nd Edition, 2014

EN61347-2-13, 2014

Lamp Controlgear Particular Requirements

D.C. or A.C. Controlgears for LED Performance Requirements

RoHS 2.1

305984-1 + 305984-1

LCS1606201548R

IEC/EN62384, 1st Edition, 2009

RoHS-2011/65/EU + AM-2015/863

continued on next page

REV.: 0/2016

L-2

www.recom-power.com

RACV06-LP

AC/DC Converter

Speciﬁcations (measured @ ta= 25°C, 240VAC and rated load)

Series

EMI Compliance

Standard / Criterion

Equipment for general Lighting Purpose - EMC Immunity Requirements

EN61547, 2009

305984

Limits and methods of measurement of radio disturbance characteristics of electrical

lighting and similar equipment

EN55015, 2015

305985

Assessment of lighting equipment related to human eꢁposure to electromagnetic ﬁelds

EN61493, 2015

8kV Air Discharge,

4kV Contact Discharge

ESD Electrostatic discharge immunity test

EN61000-4-2, 2009, Criteria B

EN61000-4-3, 2010, Criteria A

EN61000-4-4, 2012, Criteria B

Radiated, radio-frequency, electromagnetic ﬁeld immunity test

Fast Transient and Burst Immunity

3V/m

0.5kV (DC Output)

1kV (AC Input)

Surge Immunity

0.5kV (AC Input)

EN61000-4-5, 2014, Criteria C

EN61000-4-6, 2014, Criteria A

Immunity to conducted disturbances, induced by radio-frequency ﬁelds

95ꢀ reduction

30ꢀ reduction

EN61000-4-11, 2014, Criteria B

EN61000-4-11, 2014, Criteria C

Voltage Dips and Interuptions

Limits of Harmonic Current Emissions

EN61000-3-2, Class C, 2014

EN61000-3-3, 2013

Voltage Fluctuations and Flicker in Public Low-Voltage Systems <=16A per phase

DIMENSION and PHYSICAL CHARACTERISTICS

Parameter

Material

Type

Case

Value

Plastic (UL94V-2)

98.0 ꢁ 46.0 ꢁ 11.0mm

45g

Package Dimension (LꢁWꢁH)

Package Weight

Mechanical Dimensions

39.5

wire preparation

M3 Screws

6-7mm

FC 85.0

98.0

46.0

2 mounting screws are included

Connection via Screw Terminal

Function

Solid Wire

Stranded Wire ⁽²⁾

0.75-1.5mm²

0.5-1.5mm²

AWG

20-16

21-16

wire stripping length: 6-7mm

recommended tightening torque: 0.25Nm

tc= case temperature measuring point

FC= ﬁꢁing centers

VAC in (N) 0.75-1.5mm²

VAC in (L) 0.75-1.5mm²

LED+

LED-

0.5-1.5mm²

NC= no connection

0.5-1.5mm²

Tolerance: ꢁꢁ.ꢁ=

0.5mm

ꢁꢁ.ꢁꢁ= 0.35mm

Notes:

Note2: The use of sleeve or ferrule terminations is recommended.

www.recom-power.com

REV.: 0/2016

L-3

RACV06-LP

AC/DC Converter

Speciﬁcations (measured @ ta= 25°C, 240VAC and rated load)

Series

INSTALLATION and APPLICATION

Connection

L N

LED+

LED-

PACKAGING INFORMATION

Parameter

Packaging Dimension (LꢁWꢁH)

Packaging Quantity

Type

Value

220.0 ꢁ 109.0 ꢁ 62.0mm

10pcs

Cardboard Boꢁ

Storage Temperature Range

Storage Humidity

-20°C to +70°C

5ꢀ - 85ꢀ RH

The product information and speciﬁcations are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s eꢁplicit written

consent. A safety-critical application is deﬁned as an application where a failure of a RECOM product may reasonably be eꢁpected to endanger or cause loss of life, inﬂict bodily harm or damage property. The buyer

shall indemnify and hold harmless RECOM, its afﬁliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.

L-4

REV.: 0/2016

www.recom-power.com

相关型号：