CCARPG01 [REDLION]
MODELS ZBG AND ZBH STANDARD DUTY ENCODER;型号: | CCARPG01 |
厂家: | Red Lion Controls. Inc |
描述: | MODELS ZBG AND ZBH STANDARD DUTY ENCODER 编码器 |
文件: | 总4页 (文件大小:737K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Bulletin No. ZBG/ZHG-D
Drawing No. LP0739
Released 02/15
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net
MODELS ZBG AND ZBH STANDARD DUTY ENCODER (Replaces MODEL RPGB)
MODEL ZHG HEAVY DUTY ENCODER (Replaces MODEL RPGH)
CURRENT SINK OUTPUTS
HIGH PULSE PER REVOLUTION (PPR) RATES
Up to 1200 PPR for fine, high-resolution counting or precision speed
measurement from slow shaft speeds.
QUADRATURE OUTPUT
For position measurement, bi-directional counting and in systems with
backlash counting requirements.
AVAILABLE WITH MS AND M12 CONNECTORS
MODEL ZHG - HEAVY-DUTY SEALED HOUSING
(Replaces Model RPGH)
MODEL ZBG and ZBH - FOR GENERAL
INDUSTRIAL SERVICE (Replaces Model RPGB)
The units contain an L.E.D. light source and a photo sensor that scans a shaft-
mounted, slotted disc. An internal pulse-shaping amplifier circuit delivers a
rectangular pulse signal from the current sinking output in response to the passing
slots as it rotates. They can be direct-coupled to a machine shaft by means of a
flexible-bellows, spring, or rubber sleeve type coupling that allows for axial and
radial misalignment. They can also be coupled with light instrument timing-belts.
Timing-belt drives also allow convenient gear-up or gear-down speed ratio
changes that can be useful for obtaining non-standard PPR rates.
These heavy duty units feature a heavy cast aluminum housing with 1/4"
thick aluminum cover plates and 0-ring seals. Heavy duty bearings are double-
sealed and allow radial shaft loading of 40 lbs (18 Kg).
A 1/2" (12.7 mm) NPT Conduit entry permits signal wiring to be run via flex-
conduit to an internal terminal block. Electrical characteristics are identical to
those for the Model ZBG. Terminal board markings correspond to the Pin-Out
identification of the ZBG.
DIMENSIONS In Inches (mm)
DIMENSIONS In inches (mm)
MS TYPE CONNECTOR,
6-PIN, #14S-6P-6 or M12 CONNECTOR, 8-PIN
BOTTOM VIEW
FRONT VIEW
6-32 THD .25" DEEP ON
2 (50.8) DIA. BOLT CIRCLE
(BOTH SHAFT ENDS & BOTTOM)
3
.095
(2.41)
(76.2)
2.25
(57.15)
.974 MAX.
(24.7)
.375 (9.5) DIA. SHAFT
.750 (19) LONG, BOTH ENDS
6 (152.4)
3 (76.2)
2.25 (57.15)
2.25 (57.15)
1/4" - 20 THD, 1/2" DEEP ON 2" (50.8) DIA.
BOLT CIRCLE 4 HOLE PATTERN,
FRONT AND BOTTOM
TOP VIEW
1/2" NPT
CONDUIT
THD
.375 DIA. SHAFT
.75 LONG, 303
STAINLESS STEEL
REMOVE THIS SIDE
COVER TO EXPOSE
TERMINAL STRIP
3 (76.2)
RIGHT SIDE VIEW (COVER REMOVED)
6
5
4
3
2
1
N.C.
N.C.
DATA
DATA
COMMON
B
A
(QUAD)
ONLY
+5 to +28VDC
1
Cable Connections
The tables below list the pin connections from the ZBG and ZHG single
channel and ZBH quadrature encoder to the optional CCARPG or CCM cable.
SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
1. SUPPLY VOLTAGE:
+4.75 to +28 VDC @ 80 mA max. from 0 °C to 85 °C
+4.75 to +24 VDC @ 80 mA max. from 0 °C to 100 °C
2. OUTPUT: Current Sinking
6-PIN
MS CONN
CABLE WIRE
COLOR
FUNCTION
M12 CONN
ZBG and ZHG (Single Channel): 250 mA max.
ZBH (Quadrature): 250 mA max. current per output. Incremental - two
square waves in quadrature with Channel A leading Channel B for clockwise
rotation. (Quad. Phase relationship is 90° ±22.5 electrical degrees)
Note: NPN Transistor outputs have 1.5 KΩ load resistors returned to supply
for internal feed back purposes. This does not interfere with the ability to
use these outputs as conventional “Open-Collector” outputs as long as
the supply voltage for the ZB is supplied by the indicator or control
receiving its output signal. The ZB’s internal load resistor also allows the
output to be used as a current source, however, load current must be
limited to 1 mA max.
+VDC
COMMON
A
B
C
D
E
1
2
3
4
5
RED
BLACK
WHITE
GREEN
—
DATA A
DATA B if appl. (quad)
NO CONNECTION
ORDERING INFORMATION
MODEL NO. DESCRIPTION
3. MAXIMUM FREQUENCY:
Single Channel: 20 KHz
Quadrature: 20 KHz
PPR available up to 1270 for both single channel and quadrature.
PPR*
600
1000
1200
60
PART NUMBER
ZHG06004
ZHG10004
ZHG12004
ZBG00602
ZBG01002
ZBG06002
ZBG10002
ZBG12002
ZBG01003
ZBG06003
ZBH00102
ZBH00122
ZBH01002
ZBH01202
ZBH05002
ZBH06002
ZBH01003
ZBH06003
Single Channel - Heavy Duty
Rotary Pulse Generator
ZHG
MECHANICAL SPECIFICATIONS
1. MAXIMUM SHAFT SPEED: 6000 RPM
2. SHAFT DIAMETER: 0.375" (9.5 mm)
3. RADIAL SHAFT LOAD: 40 lbs. operating (18 kg)
4. AXIAL SHAFT LOAD: 30 lbs operating (13.6 kg)
5. STARTING TORQUE:
* For Dual Channel contact factory
100
600
1000
1200
100
600
10
Single Channel
General Service
6-Pin MS Connector
ZBG & ZBH: 0.38 oz-in (2.68 N-mm)
ZHG: 3 oz-in (21.18 N-mm)
ZBG
6. MOMENT OF INERTIA: 6.5 x 10-6 oz-in-sec2
7. CONNECTIONS: 6-pin MS style or 8-Pin M12 connector. (Male) Mating
connector and cable assembly sold separately. For wiring cofiguration, see
Cable Connections. For Ordering Information, see Accessories.
8. HOUSING: Black non-corrosive finished 6063-T6 aluminum.
9. BEARINGS: ABEC3 double sealed ball bearings
10. WEIGHT:
Single Channel General Service
M12 Connector
12
Dual Channel
General Service
6-Pin MS Connector
100
120
500
600
100
600
ZBG & ZBH: 10 oz (283.5 g)
ZHG: 3.8 lbs (1.72 Kg)
ZBH
ENVIRONMENTAL SPECIFICATIONS
1. OPERATING TEMPERATURE: 0 ° to 100 °C (See supply voltage)
2. STORAGE TEMPERATURE: -25°C to +85°C
3. HUMIDITY: 98% RH non-condensing
Dual Channel General Service
M12 Connector
4. VIBRATION: 10 g @ 58 to 500 Hz
5. SHOCK: 50 g @ 11 msec duration
Note: Only factory stocked part numbers are listed. Consult factory for part
number and availability of other PPR and output configurations.
Do not dispose of unit in trash - Recycle
ELECTRICAL CONNECTIONS
CABLE & CONNECTOR ASSY
(ORDER SEPARATELY)
SINGLE CHANNEL
+VDC
LED
ACCESSORIES
PULSE
SHAPING
AMPLIFIER
DATA A
MODEL NO. DESCRIPTION
PART NUMBER
RPGFC002
RPGFC003
RPGFC004
RPGFC006
CCARPG00
CCARPG01
CCARPG25
CCARPG50
CCM12894
CCM12890
SLOTTED
DISC
Flexible Coupling (1" Length) 0.250"-0.375"
COMMON
Flexible Coupling (1" Length) 0.375"-0.375"
Flexible Coupling (1" Length) 0.375"-0.500"
Flexible Coupling (1" Length) 0.375"-6 mm
RPGFC
PHOTO XISTOR
Mating 6-Pin MS Connector
CABLE & CONNECTOR ASSY
REF.
(ORDER SEPARATELY)
QUADRATURE
6-Pin MS Connector w/10 feet 22 AWG 4-conductor w/drain
6-Pin MS Connector w/25 feet 22 AWG 4-conductor w/drain
6-Pin MS Connector w/50 feet 22 AWG 4-conductor w/drain
M12 Connector w/4 Meter 24 AWG 5-conductor w/drain
M12 Connector w/10 Meter 24 AWG 5-conductor w/drain
+VDC
LED'S
DUAL
CHANNEL
PULSE
SHAPING
DATA A
DATA B
AMP.
SLOTTED
DISC
COMMON
PHOTO XISTOR'S
2
LENGTH SENSOR CONVERSION BRACKET WITH 6-PIN MS CONNECTOR
ADAPTS APPROPRIATE ZBG and ZBH ROTARY PULSE GENERATOR TO LENGTH MEASUREMENT
DESCRIPTION
This conversion bracket allows the customer to assemble a custom length
sensor by purchasing the following items separately.
1. Length Sensor Conversion Bracket (P/N LSCB1000)
2. An encoder with appropriate connector, PPR and output type.
3. One or two measuring wheels. Install OF & OK measuring wheels with set
screw hub facing encoder shaft (as shown). Apply thread locking material to
wheel set screw threads during installation to the encoder shaft.
4. Hinge Clamp Assembly (P/N LSAHC001)
Note: To complete installation, insure guards, shields or other devices are in
place to protect personnel from rotating equipment.
The tubular arm length of this bracket, related to the wheel axis center-line of
the encoder is 6.8" similar to the length sensors. The 10´ long, 4-wire, shielded
cable with 6-pin MS connector (included with conversion bracket) has the same
color coding as described for the encoder cable P/N CCARPG01. Screws for
mounting the conversion bracket are included.
LENGTH SENSOR MEASUREMENT ACCURACY
Factors which affect measurement accuracy include Measuring Wheel
accuracy and wear, and material conditions. Ideally, materials which are hard,
thin and strong provide good readings, conversely, soft, thick and elastic
materials can present problems in obtaining true readings. The great majority of
these situations, where this effect is consistant, can be compensated for by
applying a multiplier to the quadrature output pulse train so as to obtain a
corrected measurement. Counter or Rate Indicators with “input scaling” can
compensate for Measuring Wheel wear and material elastic and compliance
errors. In addition, English/Metric conversions may also be accomplished (See
RLC catalog for more information).
ORDERING INFORMATION
MODEL NO.
DESCRIPTION
PART NUMBER
LSCB1000
LSCB1025
LSCB1050
Length Sensor Conversion Bracket, w/10' Cable
Length Sensor Conversion Bracket, w/25' Cable
Length Sensor Conversion Bracket, w/50' Cable
LSCB
Hinge Clamp Assembly for Length Sensors &
Conversion Bracket (Above)
--
LSAHC001
LENGTH SENSOR ACCESSORIES
SEPARATE LENGTH MEASURING WHEELS - DIMENSIONS In Inches (mm)
WHEEL
CODE
WHEEL
CODE
WHEEL
CODE
OF
OR
OK
Round Section Replaceable
Tire .210" Section Dia.
Black Neoprene
Diamond Knurled Aluminum
Tread
Tan, Smooth Polyurethane
Tread
FOR USE ON: Soft, smooth
FOR USE ON: Rubber,
materials such as soft
paper, matting, cardboard,
fine weave textiles. Broad
wheel tread minimizes
contact pressure and tan
polyurethane tread
coarse weave fabrics,
rough wood surfaces,
foam, insulation.
8-32 UNF
FOR USE ON: Metal, paper,
foil, film and hard plastics.
Line contact on material
being measured,
Set Screw
10-32 UNF
Set Screw
10-32 UNF
Set Screw
.376"
(9.6)
Bore
.376"
(9.6)
Bore
+.001"
-.000"
.376"
(9.6)
Max. Speed: 600 RPM
convenient when available
measuring track is narrow
or for measuring on end of
roller beside passing
material.
Bore
+.001"
-.000"
+.001"
-.000"
minimizes marking.
Balanced version of 1ft.
circumference available.
Balanced to ANSI S2.19-
1989 Quality Grade 6.3
@ 3000 RPM.
Max. Speed: 600 RPM
Cast
Alum.
Cast
Alum.
Balanced version of 1ft.
Cast
Alum.
circumference
available.
Max. Speed: 600 RPM
Balanced to ANSI S2.19-
1989 Quality Grade 6.3
3000 RPM.
@
3/8"
(9.5)
1"
(25.4)
1"
(25.4)
SELECTING APPROPRIATE WHEEL SIZE & PPR (Pulses Per Rev.) OF ROTARY PULSE GENERATOR
When the desired output of a length sensor and wheel combination is either in feet or inch units, selection
of the proper combination is relatively straight forward. For example, with a 1-foot wheel circumference, a
1 PPR Rotary Pulse Generator will deliver 1 pulse/ft, 12 PPR would deliver 12 pulses/ft (1 pulse/inch); 100
PPR would yield 100 pulses/ft; and 120 PPR would permit measuring to 1/10th of an inch (1/120th of a foot).
3
WHEELS & REPLACEMENT TIRES FOR CODE OR WHEELS
ORDERING INFORMATION
WHEEL CODE
OK
CIRCUMFERENCE
1 foot (1/3 yd)
1/3 meter
TOLERANCE
±0.35%
±0.30%
±0.30%
±0.30%
±0.35%
PART NUMBER
WF1000OK
WM0333OK
WY0400OK
WM0400OK
WF1000BK
TORF1000
TORM0333
TORY0400
TORM0400
WHEEL CODE CIRCUMFERENCE
TOLERANCE
PART NUMBER
WF1000OR
WM0333OR
WY0400OR
WM0400OR
WF1000OF
WM0333OF
WY0400OF
WM0400OF
WF1000BF
1 foot (1/3 yd)
±0.40%
±0.40%
±0.40%
±0.40%
±0.35%
±0.30%
±0.30%
±0.30%
±0.40%
1/3 meter
OR
4/10ths yard
4/10ths meter
1 foot (1/3 yd)
1 foot (1/3 yd)
1/3 meter
4/10ths yard
4/10ths meter
1 foot (1/3 yd)
BK (Balanced)
1/3 meter
OF
Replacement Tires
for OR Wheels
4/10ths yard
4/10ths yard
4/10ths meter
4/10ths meter
BF (Balanced) 1 foot (1/3 yd)
Note: After installation of measuring wheels, ensure guards,shields or other
devices are in place to protect personnel from rotating equipment.
MODEL LSAHC - LENGTH SENSOR HINGE CLAMP ASSEMBLY
The Length Sensor Hinge Clamp Assembly provides an easy method for
attachment and mounting of the Length Sensors and LSCB1 Conversion
Bracket. The removable top on the solid zinc LSAHC mounting block
allows quick installation of the Length Sensor handle tube and provides
secure clamping retention. The mounting block pivots freely in zinc right
angle brackets to allow mounting the assembly via clearance holes for 1/4"
dia. bolts.
CAUTION: Downward tension
on signal cable can cause
wheel(s) to lift. Make sure
cable is clamped to
machine frame near
encoder and allow slack.
The lock washers must be used as indicated (between the bolt head and
the top clamp piece). Assemble the top clamp piece as follows.
1. Tighten both bolts so that the top clamp half draws down evenly on
the sensor tube.
2. Tighten the bolts until both lock washers are flat.
3. Then turn each bolt an additional ½ to ¾ turn.
NOTE: The weight at the
Length Sensor unit
provides sufficient traction
for accurate operation
when mounted as shown,
with arm angle from
horizontal not exceeding
±30°, and with hinge clamp
toward the far extreme of
the extension arm.
DIMENSIONS In inches (mm)
Lock washers (2) must be
installed between bolt heads
and top clamp piece.
2.5 (63.5)
FRONT
VIEW
.85
(21.6)
SINGLE WHEEL
2.93 (74.4)
1.25
(31.8)
DUAL WHEEL 4 (101.6)
.25 (6.3)
Model ZGH Shown
3.4
(86.4)
E-clip retaining ring (2)
2.9
(73.7)
must be installed in slots.
.88
(22.4)
TOP
4X Ø 0.31 (7.9)
VIEW
0.75 (19.0)
1.50
(38.1)
.88 (22.4)
2.00
(50.8)
0.75
(19.0)
4.50 (114.3)
5.70 (144.8)
Model ZFH Shown
Length Sensors should be mounted so measuring
wheel(s) contact ribbon, strip or web as it passes over
a roller. As an alternative, wheel(s) can be driven by
roller surface next to material being measured.
ORDERING INFORMATION
MODEL NO.
DESCRIPTION
PART NUMBER
LSAHC
Length Sensor Hinge Clamp Assembly
LSAHC001
Red Lion Controls
China
Unit 302, XinAn Plaza
Red Lion Controls
Headquarters
Red Lion Controls
Europe
Red Lion Controls
India
201-B, 2nd Floor, Park Centra
Opp 32 Mile Stone, Sector-30
Gurgaon-122002 Haryana, India
Tel +91 984 487 0503
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel +86 21 6113 3688
Fax +86 21 6113 3683
20 Willow Springs Circle
York PA 17406
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
Softwareweg 9
NL - 3821 BN Amersfoort
Tel +31 (0) 334 723 225
Fax +31 (0) 334 893 793
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明