ISL22313TFU10Z [RENESAS]
Single Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, I2C® Bus, 256 Taps; MSOP10; Temp Range: -40° to 125°C;型号: | ISL22313TFU10Z |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | Single Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, I2C® Bus, 256 Taps; MSOP10; Temp Range: -40° to 125°C 光电二极管 转换器 电阻器 |
文件: | 总15页 (文件大小:987K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATASHEET
ISL22313
FN6421
Rev 1.00
August 18, 2016
2
Single Digitally Controlled Potentiometer (XDCP™) Low Noise, Low Power, I C
Bus, 256 Taps
The ISL22313 integrates a single digitally controlled
potentiometer (DCP), control logic and non-volatile memory
on a monolithic CMOS integrated circuit.
Features
• 256 resistor taps
2
• I C serial interface
The digitally controlled potentiometer is implemented with a
- Two address pins, up to four devices per bus
combination of resistor elements and CMOS switches. The
position of the wipers are controlled by the user through the
• Non-volatile EEPROM storage of wiper position
2
I C bus interface. The potentiometer has an associated
• 14 General Purpose non-volatile registers
volatile Wiper Register (WR) and a non-volatile Initial Value
Register (IVR) that can be directly written to and read by the
user. The contents of the WR control the position of the
wiper. At power up the device recalls the contents of the
DCP’s IVR to the WR.
• High reliability
- Endurance: 1,000,000 data changes per bit per register
- Register data retention: 50 years @ T+55°C
• Wiper resistance: 70 typical @ 1mA
• Standby current <2.5µA max
The ISL22313 also has 14 general purpose non-volatile
registers that can be used as storage of lookup table for
multiple wiper position or any other valuable information.
• Shutdown current <2.5µA max
• Dual power supply
- VCC = 2.25V to 5.5V
- V- = -2.25V to -5.5V
The ISL22313 features a dual supply, that is beneficial for
applications requiring a bipolar range for DCP terminals
between V- and VCC.
• DCP terminal voltage from V- to VCC
• 10k 50kor 100k total resistance
• Extended industrial temperature range: -40 to +125°C
• 10 Lead MSOP
The DCP can be used as a three-terminal potentiometer or
as a two-terminal variable resistor in a wide variety of
applications including control, parameter adjustments, and
signal processing.
Pinout
• Pb-free plus anneal product (RoHS compliant)
ISL22313
(10 LD MSOP)
TOP VIEW
O
10
9
SCL
SDA
A1
VCC
1
2
3
4
5
RH
RW
8
7
A0
RL
V-
GND
6
FN6421 Rev 1.00
August 18, 2016
Page 1 of 15
ISL22313
Ordering Information
PART
NUMBER
(Notes 1, 2)
RESISTANCE
OPTION
(k)
TEMP.
RANGE
(°C)
PART
MARKING
PACKAGE
(RoHS COMPLIANT)
PKG. DWG. #
M10.118
ISL22313TFU10Z (No longer
available, recommended
313TZ
100
-40 to +125
10 Ld MSOP
replacement: ISL22313UFU10Z)
ISL22313UFU10Z
ISL22313WFU10Z
NOTES:
313UZ
313WZ
50
10
-40 to +125
-40 to +125
10 Ld MSOP
10 Ld MSOP
M10.118
M10.118
1. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
2. Add “-TK” suffix for 1,000 Tape and Reel option
Block Diagram
V-
V
CC
RH
SCL
SDA
A1
POWER UP
INTERFACE,
CONTROL
AND
STATUS
LOGIC
2
I C
WR
INTERFACE
VOLATILE
REGISTER
AND
A0
WIPER
CONTROL
CIRCUITRY
NON-VOLATILE
REGISTERS
RL
RW
GND
Pin Descriptions
MSOP PIN
SYMBOL
DESCRIPTION
2
1
2
SCL
SDA
A1
Open drain I C interface clock input
2
Open drain Serial data I/O for the I C interface
2
3
Device address input for the I C interface
2
4
A0
Device address input for the I C interface
5
V-
Negative supply pin
Device ground pin
6
GND
RL
7
“Low” terminal of DCP
“Wiper” terminal of DCP
“High” terminal of DCP
Power supply pin
8
RW
RH
9
10
VCC
FN6421 Rev 1.00
August 18, 2016
Page 2 of 15
ISL22313
Absolute Maximum Ratings
Thermal Information
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any Digital Interface Pin
Thermal Resistance (Typical, Note 3)
(°C/W)
120
JA
10 Lead MSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
with Respect to GND . . . . . . . . . . . . . . . . . . . . . -0.3V to V +0.3
CC
Maximum Junction Temperature (Plastic Package). . . . . . . . +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to +6V
CC
V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -6V to 0.3V
Voltage at any DCP Pin with
respect to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V- to V
CC
(10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Recommended Operating Conditions
I
W
Temperature Range (Full Industrial) . . . . . . . . . . . .-40°C to +125°C
Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15mW
Latchup . . . . . . . . . . . . . . . . . . . . . . . . . Class II, Level A at +125°C
ESD
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3kV
Machine Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400V
V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.25V to 5.5V
CC
V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-2.25V to -5.5V
Max Wiper Current Iw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±3.0mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
3. is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
JA
Analog Specifications Over recommended operating conditions unless otherwise stated. Limits are established by characterization.
MIN
TYP
MAX
SYMBOL
PARAMETER
RH to RL resistance
TEST CONDITIONS
(Note 18) (Note 4) (Note 18)
UNIT
k
R
W option
U option
T option
10
50
TOTAL
k
100
k
RH to RL resistance tolerance
-20
V-
+20
%
End-to-End Temperature Coefficient
W option
±150
±50
ppm/°C
ppm/°C
V
U, T option
V
, V
RH RL
DCP terminal voltage
Wiper resistance
V
and V to GND
RL
V
CC
RH
R
RH - floating, V = V-, force I current to
RL
the wiper, I = (V
70
10/10/25
0.1
250
W
W
- V )/R
W
CC RL TOTAL
C /C /C
W
Potentiometer capacitance
Leakage on DCP pins
See Macro Model below.
pF
µA
H
L
(Note 16)
I
Voltage at pin from GND to V
1
LkgDCP
CC
VOLTAGE DIVIDER MODE (V- @ RL; V
@ RH; measured at RW, unloaded)
W option
CC
INL
Integral non-linearity
-1.5
±0.5
1.5
LSB
(Note 9)
(Note 5)
U, T option
W option
-1.0
-1.0
±0.2
±0.4
1.0
1.0
DNL
Differential non-linearity
LSB
(Note 8)
(Note 5)
U, T option
W option
-0.5
0
±0.15
1
0.5
5
ZSerror
(Note 6)
Zero-scale error
Full-scale error
LSB
(Note 5)
U, T option
W option
0
0.5
-1
2
FSerror
(Note 7)
-5
-2
0
LSB
(Note 5)
U, T option
-1
0
TC
Ratiometric temperature coefficient
DCP register set to 80 hex
±4
ppm/°C
V
(Notes 10, 16)
FN6421 Rev 1.00
August 18, 2016
Page 3 of 15
ISL22313
Analog Specifications Over recommended operating conditions unless otherwise stated. Limits are established by characterization.
(Continued)
MIN
TYP
MAX
SYMBOL
PARAMETER
-3dB cut off frequency
TEST CONDITIONS
(Note 18) (Note 4) (Note 18)
UNIT
kHz
kHz
kHz
f
Wiper at midpoint (80hex) W option (10k)
Wiper at midpoint (80hex) U option (50k)
Wiper at midpoint (80hex) T option (100k)
1000
250
cutoff
(Note 16)
120
RESISTOR MODE (Measurements between RW and RL with RH not connected, or between RW and RH with RL not connected)
RINL
(Note 14)
Integral non-linearity
Differential non-linearity
Offset
W option
-3
±1.5
±0.3
±0.4
±0.15
1
3
MI
(Note 11)
U, T option
-1
1
MI
(Note 11)
RDNL
(Note 13)
W option
-1.5
-0.5
0
1.5
0.5
5
MI
(Note 11)
U, T option
MI
(Note 11)
Roffset
W option
MI
(Note 12)
(Note 11)
U, T option
0
0.5
2
MI
(Note 11)
TC
Resistance temperature coefficient
DCP register set between 32 hex and FF hex
±50
ppm/°C
R
(Notes 15, 16)
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by
characterization.
MIN
TYP
MAX
SYMBOL
PARAMETER
TEST CONDITIONS
= +5.5V, V- = -5.5V, f = 400kHz;
SDA = Open; (for I C, active, read and write
states)
(Note 18) (Note 4) (Note 18)
UNIT
I
V
Supply Current (volatile
V
0.07
0.02
-0.18
-0.06
1
0.15
0.05
mA
CC1
CC
CC
SCL
2
write/read)
V
= +2.25V, V- = -2.25V, f
SCL
SDA = Open; (for I C, active, read and write
= 400kHz;
mA
mA
mA
mA
mA
mA
mA
CC
2
states)
I
V- Supply Current (volatile write/read) V- = -5.5V, V
= +5.5V, f
CC SCL
SDA = Open; (for I C, active, read and write
states)
= 400kHz;
-1
V-1
2
V- = -2.25V, V
SDA = Open; (for I C, active, read and write
= +2.25V, f
SCL
= 400kHz;
-0.4
CC
2
states)
I
V
Supply Current (non-volatile
V = +5.5V, V- = -5.5V, f
CC SCL
SDA = Open; (for I C, active, read and write
= 400kHz;
2
CC2
CC
2
write/read)
states)
V
= +2.25V, V- = -2.25V, f
SCL
SDA = Open; (for I C, active, read and write
= 400kHz;
0.3
0.7
CC
2
states)
I
V- Supply Current (non-volatile
write/read)
V- = -5.5V, V
CC
SDA = Open; (for I C, active, read and write
= +5.5V, f
SCL
= 400kHz;
-2
-1.2
-0.4
V-2
2
states)
V- Supply Current (non-volatile
write/read)
V- = -2.25V, V
SDA = Open; (for I C, active, read and write
states)
= +2.25V, f
SCL
= 400kHz;
-0.7
CC
2
FN6421 Rev 1.00
August 18, 2016
Page 4 of 15
ISL22313
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by
characterization. (Continued)
MIN
TYP
MAX
SYMBOL
PARAMETER
TEST CONDITIONS
= +5.5V, V- = -5.5V @ +85°C, I C
(Note 18) (Note 4) (Note 18)
UNIT
2
I
V
Current (standby)
V
0.2
1
1.5
2.5
1
µA
SB
CC
CC
interface in standby state
2
V
= +5.5V, V- = -5.5V @ +125°C, I C
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µs
CC
interface in standby state
2
V
= +2.25V, V- = -2.25V @ +85°C, I C
0.1
0.5
-0.7
-3
CC
interface in standby state
2
V
= +2.25V, V- = -2.25V @ +125°C, I C
2
CC
interface in standby state
2
I
V- Current (standby)
V- = -5.5V, V = +5.5V @ +85°C, I C
-2.5
-4
V-SB
CC
interface in standby state
2
V- = -5.5V, V
= +5.5V @ +125°C, I C
CC
interface in standby state
2
V- = -2.25V, V = +2.25V @ +85°C, I C
-1.5
-3
-0.3
-1
CC
interface in standby state
2
V- = -2.25V, V = +2.25V @ +125°C, I C
CC
interface in standby state
2
I
V
Current (shutdown)
V
= +5.5V, V- = -5.5V @ +85°C, I C
0.2
1
1.5
2.5
1
SD
CC
CC
interface in standby state
2
V
= +5.5V, V- = -5.5V @ +125°C, I C
CC
interface in standby state
2
V
= +2.25V, V- = -2.25V @ +85°C, I C
0.1
0.5
-0.7
-3
CC
interface in standby state
2
V
= +2.25V, V- = -2.25V @ +125°C, I C
2
CC
interface in standby state
2
I
V- Current (standby)
V- = -5.5V, V = +5.5V @ +85°C, I C
-2.5
-4
V-SB
CC
interface in standby state
2
V- = -5.5V, V
= +5.5V @ +125°C, I C
CC
interface in standby state
2
V- = -2.25V, V = +2.25V @ +85°C, I C
-1.5
-3
-0.3
-1
CC
interface in standby state
2
V- = -2.25V, V = +2.25V @ +125°C, I C
CC
interface in standby state
I
Leakage current, at pins A0, A1, SDA, Voltage at pin from GND to V
and SCL
-1
1
LkgDig
CC
t
DCP wiper response time
SCL falling edge of last bit of DCP data byte
to wiper new position
1.5
1.5
DCP
(Note 16)
t
DCP recall time from shutdown mode SCL falling edge of last bit of ACR data byte
to wiper stored position and RH connection
µs
ShdnRec
(Note 16)
Vpor
Power-on recall voltage
ramp rate
Minimum V
at which memory recall occurs
1.9
0.2
2.1
5
V
CC
VCC Ramp
V
V/ms
ms
CC
t
Power-up delay
V
above Vpor, to DCP Initial Value
CC
D
2
Register recall completed, and I C Interface
in standby state
EEPROM SPECIFICATION
EEPROM Endurance
1,000,000
50
Cycles
Years
ms
EEPROM Retention
Temperature T +55°C
t
Non-volatile Write cycle time
12
20
WC
(Note 17)
FN6421 Rev 1.00
August 18, 2016
Page 5 of 15
ISL22313
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by
characterization. (Continued)
MIN
TYP
MAX
SYMBOL
PARAMETER
TEST CONDITIONS
(Note 18) (Note 4) (Note 18)
UNIT
SERIAL INTERFACE SPECS
V
A1, A0, SDA, and SCL input buffer
LOW voltage
-0.3
0.3*V
V
V
IL
CC
V
A1, A0, SDA, and SCL input buffer
HIGH voltage
0.7*V
V
+ 0.
CC
IH
CC
3
Hysteresis SDA and SCL input buffer hysteresis
(Note 16)
0.05*V
V
CC
V
SDA output buffer LOW voltage,
0
0.4
10
V
OL
(Note 16) sinking 4mA
Cpin
A1, A0, SDA, and SCL pin
pF
(Note 16) capacitance
f
SCL frequency
Pulse width suppression time at SDA Any pulse narrower than the max spec is
400
50
kHz
ns
SCL
t
sp
and SCL inputs suppressed
t
SCL falling edge to SDA output data SCL falling edge crossing 30% of V , until
CC
900
ns
ns
AA
(Note 16) valid
SDA exits the 30% to 70% of V
window
CC
t
Time the bus must be free before the SDA crossing 70% of V
during a STOP
1300
BUF
(Note 16) start of a new transmission
CC
condition, to SDA crossing 70% of V
CC
during the following START condition
t
Clock LOW time
Measured at the 30% of V
Measured at the 70% of V
crossing
crossing
1300
600
ns
ns
ns
LOW
CC
CC
t
Clock HIGH time
HIGH
t
START condition setup time
SCL rising edge to SDA falling edge; both
crossing 70% of V
600
SU:STA
HD:STA
SU:DAT
CC
From SDA falling edge crossing 30% of V
t
t
START condition hold time
Input data setup time
600
100
ns
ns
CC
to SCL falling edge crossing 70% of V
CC
From SDA exiting the 30% to 70% of V
CC
window, to SCL rising edge crossing 30% of
V
CC
t
Input data hold time
From SCL rising edge crossing 70% of V
0
ns
HD:DAT
CC
to SDA entering the 30% to 70% of V
window
CC
t
STOP condition setup time
From SCL rising edge crossing 70% of V
to SDA rising edge crossing 30% of V
,
600
1300
0
ns
ns
ns
SU:STO
CC
CC
t
STOP condition hold time for read, or From SDA rising edge to SCL falling edge;
volatile only write
HD:STO
both crossing 70% of V
CC
t
Output data hold time
From SCL falling edge crossing 30% of V
,
DH
(Note 16)
CC
CC
until SDA enters the 30% to 70% of V
window
t
SDA and SCL rise time
From 30% to 70% of V
20 +
0.1 * Cb
250
250
400
ns
ns
R
CC
(Note 16)
t
SDA and SCL fall time
From 70% to 30% of V
20 +
0.1 * Cb
F
CC
(Note 16)
Cb
(Note 16)
Capacitive loading of SDA or SCL
Total on-chip and off-chip
10
pF
k
Rpu
SDA and SCL bus pull-up resistor
Maximum is determined by t and t
R F
1
(Note 16) off-chip
For Cb = 400pF, max is about 2k~2.5k
For Cb = 40pF, max is about 15k~20k
FN6421 Rev 1.00
August 18, 2016
Page 6 of 15
ISL22313
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by
characterization. (Continued)
MIN
TYP
MAX
SYMBOL
PARAMETER
A1 and A0 setup time
A1 and A0 hold time
TEST CONDITIONS
Before START condition
After STOP condition
(Note 18) (Note 4) (Note 18)
UNIT
ns
t
600
600
SU:A
t
ns
HD:A
NOTES:
4. Typical values are for T = +25°C and 3.3V supply voltage.
A
5. LSB: [V(R
)
– V(R ) ]/255. V(R
)
and V(R ) are V(R ) for the DCP register set to FF hex and 00 hex respectively. LSB is the
W 0
W 255
W 0 W 255
W
incremental voltage when changing from one tap to an adjacent tap.
6. ZS error = V(RW) /LSB.
0
7. FS error = [V(RW)
– V ]/LSB.
CC
255
8. DNL = [V(RW) – V(RW) ]/LSB-1, for i = 1 to 255. i is the DCP register setting.
i-1
i
9. INL = [V(RW) – i • LSB – V(RW) ]/LSB for i = 1 to 255
i
0
MaxVRW – MinVRW
6
10
i
i
10.
for i = 16 to 255 decimal, T = -40°C to +125°C. Max( ) is the maximum value of the wiper
MaxVRW + MinVRW 2 165°C voltage and Min ( ) is the minimum value of the wiper voltage over the temperature range.
--------------------------------------------------------------------------------------------- ----------------
TC
=
V
+
i
i
11. MI = |RW
– RW |/255. MI is a minimum increment. RW
and RW are the measured resistances for the DCP register set to FF hex and
255 0
255
0
00 hex respectively.
12. Roffset = RW /MI, when measuring between RW and RL.
0
Roffset = RW
/MI, when measuring between RW and RH.
255
13. RDNL = (RW – RW )/MI -1, for i = 16 to 255.
i-1
i
14. RINL = [RW – (MI • i) – RW ]/MI, for i = 16 to 255.
i
0
6
15.
for i = 16 to 255, T = -40°C to +125°C. Max( ) is the maximum value of the resistance and Min ( ) is
the minimum value of the resistance over the temperature range.
MaxRi – MinRi
10
--------------------------------------------------------------- ----------------
165°C
MaxRi + MinRi 2 +
TC
=
R
16. Limits should be considered typical and are not production tested.
2
17. t is the time from a valid STOP condition at the end of a Write sequence of I C serial interface, to the end of the self-timed internal non-volatile
WC
write cycle.
18. Parts are 100% tested at +25°C. Over temperature limits established by characterization and are not production tested.
DCP Macro Model
R
TOTAL
RH
RL
C
L
C
H
C
W
10pF
10pF
25pF
RW
SDA vs SCL Timing
t
sp
t
t
t
t
R
F
HIGH
LOW
SCL
t
SU:DAT
t
t
t
SU:STO
SU:STA
HD:DAT
t
HD:STA
SDA
(INPUT TIMING)
t
t
t
BUF
AA
DH
SDA
(OUTPUT TIMING)
FN6421 Rev 1.00
August 18, 2016
Page 7 of 15
ISL22313
A0 and A1 Pin Timing
STOP
START
SCL
CLK 1
SDA
t
t
HD:A
SU:A
A0, A1
Typical Performance Curves
80
2.0
1.5
1.0
0.5
0
T = +125ºC
70
60
50
40
30
20
10
0
T = +25ºC
I
CC
-0.5
-1.0
-1.5
-2.0
I
V-
T = -40ºC
0
50
100
150
200
250
-40
0
40
TEMPERATURE (°C)
80
120
TAP POSITION (DECIMAL)
FIGURE 2. STANDBY I
AND I vs TEMPERATURE
V-
FIGURE 1. WIPER RESISTANCE vs TAP POSITION
[ I(RW) = V /R ] FOR 10k (W)
CC
CC TOTAL
0.50
0.50
0.25
0
V
= 5.5V
CC
T = +25ºC
T = +25ºC
V
= 2.25V
CC
0.25
0
-0.25
-0.50
-0.25
-0.50
V
= 5.5V
V
= 2.25V
100
CC
100
TAP POSITION (DECIMAL)
CC
0
50
150
200
250
0
50
150
200
250
TAP POSITION (DECIMAL)
FIGURE 4. INL vs TAP POSITION IN VOLTAGE DIVIDER
FIGURE 3. DNL vs TAP POSITION IN VOLTAGE DIVIDER
MODE FOR 10k (W)
MODE FOR 10k (W)
FN6421 Rev 1.00
August 18, 2016
Page 8 of 15
ISL22313
Typical Performance Curves (Continued)
2.0
0
10k
1.6
1.2
-1
-2
V
= 2.25V
CC
50k
V
= 5.5V
CC
0.8
50k
-3
-4
10k
V
= 2.25V
V
= 5.5V
CC
CC
0.4
0
-5
-40
0
40
80
120
-40
0
40
TEMPERATURE (ºC)
80
120
TEMPERATURE (ºC)
FIGURE 5. ZS ERROR vs TEMPERATURE
FIGURE 6. FS ERROR vs TEMPERATURE
2.0
0.5
0.25
0
T = +25ºC
T = +25ºC
V
= 5.5V
1.5
1.0
CC
V
= 2.25V
CC
0.5
0
-0.25
-0.50
V
= 2.25V
100
CC
V
= 5.5V
CC
50
-0.5
0
100
150
200
250
0
50
150
200
250
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 7. DNL vs TAP POSITION IN RHEOSTAT MODE FOR
FIGURE 8. INL vs TAP POSITION IN RHEOSTAT MODE FOR
10k (W)
10k (W)
200
1.60
10k
160
1.20
10k
120
80
0.80
5.5V
0.40
0.00
50k
40
50k
2.25V
0
-0.40
16
66
116
166
216
266
-40
0
40
80
120
TAP POSITION (DECIMAL)
TEMPERATURE (ºC)
FIGURE 10. TC FOR VOLTAGE DIVIDER MODE IN ppm
FIGURE 9. END TO END R
TOTAL
% CHANGE vs
TEMPERATURE
FN6421 Rev 1.00
August 18, 2016
Page 9 of 15
ISL22313
Typical Performance Curves (Continued)
500
INPUT
OUTPUT
10k
400
300
200
50k
100
WIPER AT MID POINT (POSITION 80h)
= 10k
R
TOTAL
0
16
66
116
166
216
TAP POSITION (DECIMAL)
FIGURE 12. FREQUENCY RESPONSE (1MHz)
FIGURE 11. TC FOR RHEOSTAT MODE IN ppm
CS
SCL
WIPER UNLOADED,
WIPER
MOVEMENT FROM 0h to FFh
FIGURE 13. MIDSCALE GLITCH, CODE 7Fh TO 80h
FIGURE 14. LARGE SIGNAL SETTLING TIME
Bus Interface Pins
Pin Description
Serial Data Input/Output (SDA)
Potentiometers Pins
2
The SDA is a bidirectional serial data input/output pin for I C
interface. It receives device address, operation code, wiper
RH and RL
The high (RH) and low (RL) terminals of the ISL22313 are
equivalent to the fixed terminals of a mechanical
potentiometer. RH and RL are referenced to the relative
position of the wiper and not the voltage potential on the
terminals. With WR set to 255 decimal, the wiper will be closest
to RH, and with the WR set to 0, the wiper is closest to RL.
2
address and data from an I C external master device at the
rising edge of the serial clock SCL, and it shifts out data after
each falling edge of the serial clock.
SDA requires an external pull-up resistor, since it is an open
drain input/output.
Serial Clock (SCL)
RW
2
This input is the serial clock of the I C serial interface. SCL
RW is the wiper terminal, and it is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the WR register.
requires an external pull-up resistor, since it is an open drain
input.
FN6421 Rev 1.00
August 18, 2016
Page 10 of 15
ISL22313
Device Address (A1, A0)
Control Register (ACR). Memory map of ISL22313 is in Table 1.
The non-volatile register (IVR) at address 0, contains initial wiper
position and volatile register (WR) contains current wiper position.
The address inputs are used to set the least significant 2 bits of
2
the 7-bit I C interface slave address. A match in the slave
TABLE 1. MEMORY MAP
address serial data stream must match with the Address input
pins in order to initiate communication with the ISL22313. A
maximum of four ISL22313 devices may occupy the I C serial
ADDRESS
2
(hex)
10
F
NON-VOLATILE
VOLATILE
bus (see Table 3).
N/A
ACR
Reserved
Principles of Operation
E
D
C
B
A
9
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
IVR
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
WR
The ISL22313 is an integrated circuit incorporating one DCP
with its associated registers, non-volatile memory and an I C
2
serial interface providing direct communication between a host
and the potentiometer and memory. The resistor array is
comprised of individual resistors connected in series. At either
end of the array and between each resistor is an electronic
switch that transfers the potential at that point to the wiper.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions.
8
7
When the device is powered down, the last value stored in IVR
will be maintained in the non-volatile memory. When power is
restored, the contents of the IVR are recalled and loaded into
the WR to set the wiper to the initial value.
6
5
4
DCP Description
3
The DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of each DCP
are equivalent to the fixed terminals of a mechanical
2
1
0
potentiometer (RH and RL pins). The RW pin of the DCP is
connected to intermediate nodes, and is equivalent to the
wiper terminal of a mechanical potentiometer. The position of
the wiper terminal within the DCP is controlled by an 8-bit
volatile Wiper Register (WR). When the WR of a DCP contains
all zeroes (WR[7:0]= 00h), its wiper terminal (RW) is closest to
its “Low” terminal (RL). When the WR register of a DCP
contains all ones (WR[7:0]= FFh), its wiper terminal (RW) is
closest to its “High” terminal (RH). As the value of the WR
increases from all zeroes (0) to all ones (255 decimal), the
wiper moves monotonically from the position closest to RL to
the position closest to RH. At the same time, the resistance
between RW and RL increases monotonically, while the
resistance between RH and RW decreases monotonically.
The non-volatile IVR and volatile WR registers are accessible
with the same address.
The Access Control Register (ACR) contains information and
control bits described below in Table 2.
The VOL bit (ACR[7]) determines whether the access to wiper
registers WR or initial value registers IVR.
TABLE 2. ACCESS CONTROL REGISTER (ACR)
BIT #
7
6
5
4
0
3
0
2
0
1
0
0
0
NAME
VOL
SHDN WIP
If VOL bit is 0, the non-volatile IVR register is accessible. If
VOL bit is 1, only the volatile WR is accessible. Note: Value is
written to IVR register also is written to the WR. The default
value of this bit is 0.
While the ISL22313 is being powered up, the WR is reset to
80h (128 decimal), which locates RW roughly at the center
between RL and RH. After the power supply voltage becomes
large enough for reliable non-volatile memory reading, the WR
will be reloaded with the value stored in a non-volatile Initial
Value Register (IVR).
The SHDN bit (ACR[6]) disables or enables Shutdown mode.
When this bit is 0, i.e. DCP is forced to end-to-end open circuit
and RW is shorted to RL as shown on Figure 15. Default value
of the SHDN bit is 1.
The WR and IVR can be read or written to directly using the
2
I C serial interface as described in the following sections.
Memory Description
The ISL22313 contains one non-volatile 8-bit Initial Value Register
(IVR), fourteen General Purpose non-volatile 8-bit registers and
two volatile 8-bit registers: Wiper Register (WR) and Access
FN6421 Rev 1.00
August 18, 2016
Page 11 of 15
ISL22313
2
All I C interface operations must begin with a START
RH
condition, which is a HIGH to LOW transition of SDA while SCL
is HIGH. The ISL22313 continuously monitors the SDA and
SCL lines for the START condition and does not respond to
any command until this condition is met (see Figure 16). A
START condition is ignored during the power-up of the device.
RW
RL
2
All I C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while SCL
is HIGH (see Figure 16). A STOP condition at the end of a read
operation, or at the end of a write operation places the device
in its standby mode.
FIGURE 15. DCP CONNECTION IN SHUTDOWN MODE
The WIP bit (ACR[5]) is a read-only bit. It indicates that non-
volatile write operation is in progress. It is impossible to write to
the WR or ACR while WIP bit is 1.
An ACK (Acknowledge) is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after transmitting
eight bits. During the ninth clock cycle, the receiver pulls the
SDA line LOW to acknowledge the reception of the eight bits of
data (see Figure 17).
2
I C Serial Interface
2
The ISL22313 supports an I C bidirectional bus oriented
protocol. The protocol defines any device that sends data onto
the bus as a transmitter and the receiving device as the
receiver. The device controlling the transfer is a master and the
device being controlled is the slave. The master always
initiates data transfers and provides the clock for both transmit
and receive operations. Therefore, the ISL22313 operates as a
slave device in all applications.
The ISL22313 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL22313 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation
2
All communication over the I C interface is conducted by
sending the MSB of each byte of data first.
A valid Identification Byte contains 10100 as the five MSBs,
and the following two bits matching the logic values present at
pins A1 and A0. The LSB is the Read/Write bit. Its value is “1”
for a Read operation and “0” for a Write operation (see Table
3).
Protocol Conventions
Data states on the SDA line must change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (see
Figure 16). On power-up of the ISL22313, the SDA pin is in the
input mode.
TABLE 3. IDENTIFICATION BYTE FORMAT
LOGIC VALUES AT PINS A1 AND A0, RESPECTIVELY
1
0
1
0
0
A1
A0
R/W
(MSB)
(LSB)
SCL
SDA
START
DATA
DATA
DATA
STOP
STABLE
CHANGE STABLE
FIGURE 16. VALID DATA CHANGES, START AND STOP CONDITIONS
FN6421 Rev 1.00
August 18, 2016
Page 12 of 15
ISL22313
SCL FROM
MASTER
1
8
9
SDA OUTPUT FROM
TRANSMITTER
HIGH IMPEDANCE
HIGH IMPEDANCE
SDA OUTPUT FROM
RECEIVER
START
ACK
FIGURE 17. ACKNOWLEDGE RESPONSE FROM RECEIVER
WRITE
S
SIGNALS FROM
THE MASTER
T
A
R
T
S
T
O
P
IDENTIFICATION
BYTE
ADDRESS
BYTE
DATA
BYTE
SIGNAL AT SDA
1 0 1 0 0 A1A0 0
0 0 0 0
SIGNALS FROM
THE SLAVE
A
C
K
A
C
K
A
C
K
FIGURE 18. BYTE WRITE SEQUENCE
S
T
A
R
T
S
T
A
R
T
SIGNALS
FROM THE
MASTER
S
T
O
P
A
C
K
A
C
K
IDENTIFICATION
BYTE WITH
R/W = 0
IDENTIFICATION
BYTE WITH
R/W = 1
A
C
K
ADDRESS
BYTE
SIGNAL AT SDA
1 0 1 0 0A1A0 0
0 0 0 0
1 0 1
0 A1A0 1
0
A
C
K
A
C
K
A
C
K
SIGNALS FROM
THE SLAVE
FIRST READ
DATA BYTE
LAST READ
DATA BYTE
FIGURE 19. READ SEQUENCE
Write Operation
Read Operation
A Read operation consist of a three byte instruction followed by
one or more Data Bytes (see Figure 19). The master initiates
the operation issuing the following sequence: a START, the
Identification byte with the R/W bit set to “0”, an Address Byte,
a second START, and a second Identification byte with the R/W
bit set to “1”. After each of the three bytes, the ISL22313
responds with an ACK. Then the ISL22313 transmits Data
Bytes as long as the master responds with an ACK during the
SCL cycle following the eighth bit of each byte. The Data Bytes
are from the registers indicated by an internal pointer. This
pointer initial value is determined by the Address Byte in the
Read operation instruction, and increments by one during
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte, and
a STOP condition. After each of the three bytes, the ISL22313
responds with an ACK. At this time, the device enters its
standby state (see Figure 18).
The non-volatile write cycle starts after STOP condition is
determined and it requires up to 20ms delay for the next non-
volatile write. Thus, non-volatile registers must be written
individually.
FN6421 Rev 1.00
August 18, 2016
Page 13 of 15
ISL22313
transmission of each Data Byte. After reaching the memory
location 0Fh, the pointer “rolls over” to 00h, and the device
continues to output data for each ACK received.The master
terminates the read operation issuing a NACK (ACK ) and a
STOP condition following the last bit of the last Data Byte
(see Figure 19).
much higher impedance “break within an extremely short
period of time (<50ns). Two such code transitions are EFh to
F0h, and 0Fh to 10h. Note that all switching transients will
settle well within the settling time as stated in the datasheet.
A small capacitor can be added externally to reduce the
amplitude of these voltage transients, but that will also
reduce the useful bandwidth of the circuit, thus this may not
be a good solution for some applications. It may be a good
idea, in that case, to use fast amplifiers in a signal chain for
fast recovery.
Applications Information
When stepping up through each tap in voltage divider mode,
some tap transition points can result in noticeable voltage
transients (or overshoot/undershoot) resulting from the
sudden transition from a very low impedance “make” to a
Revision History The revision history provided is for informational purposes only and is believed to be accurate, however, not warranted.
Please go to web to make sure you have the latest revision.
DATE
REVISION
CHANGE
Updated the Ordering information table on page 2.
August 18, 2016
FN6421.1
Added Revision History and About Intersil sections.
Updated POD M10.118 to the latest revision. Changes are as follows:
Updated to new POD template and added land pattern.
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support.
© Copyright Intersil Americas LLC 2007. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6421 Rev 1.00
August 18, 2016
Page 14 of 15
ISL22313
Package Outline Drawing
M10.118
10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
Rev 1, 4/12
5
3.0±0.05
A
DETAIL "X"
D
10
1.10 MAX
SIDE VIEW 2
0.09 - 0.20
4.9±0.15
3.0±0.05
5
0.95 REF
PIN# 1 ID
1
2
0.50 BSC
B
GAUGE
PLANE
TOP VIEW
0.25
3°±3°
0.55 ± 0.15
DETAIL "X"
0.85±010
H
C
SEATING PLANE
0.10 C
0.18 - 0.27
0.10 ± 0.05
0.08
C A-B D
M
SIDE VIEW 1
(5.80)
NOTES:
1. Dimensions are in millimeters.
(4.40)
(3.00)
2. Dimensioning and tolerancing conform to JEDEC MO-187-BA
and AMSEY14.5m-1994.
3. Plastic or metal protrusions of 0.15mm max per side are not
included.
(0.50)
4. Plastic interlead protrusions of 0.15mm max per side are not
included.
5. Dimensions are measured at Datum Plane "H".
6. Dimensions in ( ) are for reference only.
(0.29)
(1.40)
TYPICAL RECOMMENDED LAND PATTERN
FN6421 Rev 1.00
August 18, 2016
Page 15 of 15
相关型号:
ISL22313TFU10Z-TK
Single Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, I2C® Bus, 256 Taps; MSOP10; Temp Range: -40° to 125°C
RENESAS
ISL22313UFU10Z-TK
Single Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, I2C® Bus, 256 Taps; MSOP10; Temp Range: -40° to 125°C
RENESAS
ISL22313WFU10Z
Single Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, I2C® Bus, 256 Taps; MSOP10; Temp Range: -40° to 125°C
RENESAS
ISL22313WFU10Z-TK
Single Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, I2C® Bus, 256 Taps; MSOP10; Temp Range: -40° to 125°C
RENESAS
ISL22316UFRT10Z
Low Noise, Low Power I2C® Bus, 128 Taps; DFN10, MSOP10; Temp Range: -40° to 125°C
RENESAS
ISL22316UFRT10Z-TK
Low Noise, Low Power I2C® Bus, 128 Taps; DFN10, MSOP10; Temp Range: -40° to 125°C
RENESAS
©2020 ICPDF网 联系我们和版权申明