ISL26104 [RENESAS]
Low-Noise 24-bit Delta Sigma ADC;
| 型号： | ISL26104 |
| 厂家： | 
RENESAS TECHNOLOGY CORP |
| 描述： | Low-Noise 24-bit Delta Sigma ADC |
| 文件： | 总21页 (文件大小：1221K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DATASHEET
ISL26102, ISL26104
Low-Noise 24-bit Delta Sigma ADC
FN7608
Rev 0.00
October 12, 2012
The ISL26102 and ISL26104 provide a low-noise
Features
• Programmable gain amplifier with gains of 1 to 128
• Low noise: 7nV/√Hz @ PGA = 128
• Linearity error: 0.0002% FS
programmable gain amplifier along with a 24-bit Delta-Sigma
Analog-to-Digital Converter with two channel (ISL26102) or
four channel (ISL26104) differential, multiplexed inputs. The
devices feature exceptional noise performance for conversion
rates ranging from 2.5Sps to 4kSps.
• Output word rates up to 4kSps
The on-chip low-noise programmable-gain amplifier provides
gains ranging from 1 to 128, which supports ±19.5mVFS from
a 5V reference. The high input impedance allows direct
connection of sensors such as load cell bridges to ensure the
specified measurement accuracy without additional circuitry.
• Low-side switch for load cell power management
• +5V analog and +2.7V to +5V digital supplies
• ISL26102 in 24 Ld TSSOP
• ISL26104 in 28 Ld TSSOP
The Delta-Sigma ADC features a 3rd-order modulator providing
up to 21.5 bit noise-free performance (10Sps), with
user-selectable word rates. The converter can be operated
from an external clock source, an external crystal (typically
4.9152MHz), or the on-chip oscillator.
• ESD 7.5kV - HBM
Applications
• Weigh scales
The ISL26102 and ISL26104 offer a simple-to-use serial
interface.
• Temperature monitors and controls
• Load safety systems
• Industrial process control
• Pressure sensors
The ISL26102 and ISL26104 are available in a Thin Shrink
Small Outline Package (TSSOP). The devices are specified for
operation over the automotive temperature range (-40°C to
+105°C).
Related Literature
AN1704, “Precision Signal Path Data Acquisition System”
CAP
AVDD
DVDD
DVDD
ON-CHIP
TEMP
SENSOR
XTALIN/
CLOCK
XTALOUT
INTERNAL
CLOCK
EXTERNAL
OSCILLATOR
AIN1+
AIN1-
CS
AIN2+
SDO/RDY
PGA
1, 2, 4, 8,16,
32, 64, 128
AIN2-
ADC
INPUT
MULTIPLEXER
AIN3+
AIN3-
SDI
ISL26104
ONLY
AIN4+
AIN4-
SCLK
PWDN
LSPS
DGND DGND
AGND
CAP DGND DGND VREF+ VREF-
FIGURE 1. BLOCK DIAGRAM
FN7608 Rev 0.00
October 12, 2012
Page 1 of 21
ISL26102, ISL26104
Ordering Information
PART NUMBER
(Notes 1, 2, 3)
PART
MARKING
TEMP RANGE
(°C)
PACKAGE
(Pb-free)
PKG.
DWG. #
DESCRIPTION
2 Channel ADC
4 Channel ADC
ISL26102AVZ
ISL26104AVZ
26102 AVZ
26104 AVZ
-40 to +105
-40 to +105
24 Ld TSSOP
28 Ld TSSOP
M24.173
M28.173
ISL26104AV28EV1Z Evaluation Board
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pbfree products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL26102, ISL26104. For more information on MSL please see techbrief
TB363.
Pin Configurations
ISL26102
(24 LD TSSOP)
TOP VIEW
ISL26104
(28 LD TSSOP)
TOP VIEW
DVDD
DGND
28
1
2
3
4
5
6
7
8
9
SDO/RDY
24
DVDD
DGND
1
2
SDO/RDY
27 SCLK
23 SCLK
XTALIN/CLOCK
XTALOUT
DGND
26
25
24
23
22
21
20
19
18
17
16
15
PDWN
SDI
22
21
XTALIN/CLOCK
XTALOUT
DGND
3
PDWN
SDI
4
CS
20 CS
5
DVDD
LSPS
AVDD
AGND
VREF+
VREF-
AIN2+
AIN2-
AIN4+
AIN4-
19 LSPS
DVDD
6
ISL26102
DGND
AVDD
AGND
VREF+
VREF-
AIN2+
AIN2-
18
17
16
15
14
13
DGND
7
ISL26104
DGND
DGND
8
CAP
9
CAP
CAP 10
AIN1+ 11
AIN1- 12
AIN3+ 13
AIN3- 14
10
11
12
CAP
AIN1+
AIN1-
FN7608 Rev 0.00
October 12, 2012
Page 2 of 21
ISL26102, ISL26104
Pin Descriptions (TSSOP)
PIN NUMBER
ANALOG/DIGITAL
INPUT/OUTPUT
PIN NAME
DVDD
ISL26102
1, 6
ISL26104
1, 6
DESCRIPTION
Digital
Digital Power Supply (2.7V to 5.25V)
DGND
2, 5, 7, 8
3
2, 5, 7, 8
3
Digital
Digital Ground
XTALIN/CLOCK
Digital/Digital Input
External Clock Input: Typically 4.9152MHz. Tie low
to activate internal oscillator. Can also use external
crystal across XTALIN/CLOCK and XTALOUT pins.
XTALOUT
CAP
4
9, 10
11
12
-
4
9, 10
11
Digital
External Crystal Connection
PGA Filter Capacitor
Analog
AIN1+
AIN1-
Analog Input
Analog Input
Analog Input
Positive Analog Input Channel 1
Negative Analog Input Channel 1
Positive Analog Input Channel 3
12
AIN3+
13
AIN3-
AIN4-
AIN4+
AIN2-
AIN2+
VREF-
VREF+
AGND
AVDD
LSPS
-
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Analog Input
Analog Input
Analog Input
Analog Input
Analog Input
Analog Input
Analog Input
Analog Input
Analog Input
Digital Output
Digital Input
Digital Input
Digital Input
Digital Input
Digital Output
Negative Analog Input Channel 3
Negative Analog Input Channel 4
Positive Analog Input Channel 4
Negative Analog Input Channel 2
Positive Analog Input Channel 2
Negative Reference Input
Positive Reference Input
-
-
13
14
15
16
17
18
19
20
21
22
23
24
Analog Ground
Analog Power Supply 4.75V to 5.25V
Low-Side Power Switch (Open Drain)
Chip Select (Active Low)
CS
SDI
Serial Data Input
PDWN
SCLK
Device Power Down (Active Low)
Serial Port Clock
SDO/RDY
Data Ready signal (conversion complete) and
Serial Data Output
FN7608 Rev 0.00
October 12, 2012
Page 3 of 21
ISL26102, ISL26104
Absolute Maximum Ratings
Thermal Information
A
to D
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V
Thermal Resistance (Typical)
24 Ld TSSOP Package (Notes 4, 5) . . . . . .
28 Ld TSSOP Package (Notes 4, 5) . . . . . .
JA (°C/W)
65
JC (°C/W)
GND
GND
Analog In to A
Digital In to D
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to A
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3 to D
+0.3V
+0.3V
18
18
GND
GND
VDD
VDD
63
ESD Rating
Maximum Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80mW
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . . . . . .7.5kV
Machine Model (Per JESD22-A115). . . . . . . . . . . . . . . . . . . . . . . . . . 450V
Charged Device Model (Per JESD22-C101) . . . . . . . . . . . . . . . . . . . . . . 2000V
Input Current
Momentary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA
Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
Latch-up
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C
A
D
to A
to D
GND
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.75V to +5.25V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.7V to +5.25V
VDD
VDD
GND
(Per JEDEC, JESD-78C; Class 2, Level A). . . .100mA @ +25°C and +105°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
JA
5. For , the “case temp” location is taken at the package top center.
JC
Electrical Specifications
V
+ = 5.0V, V
- = 0V, A
= 5V, D
= 5V XTALIN/CLOCK = 4.9152MHz (Note 6)
REF
REF
VDD
VDD
T
= -40°C to +105°C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +105°C.
A
MIN
MAX
SYMBOL
ANALOG INPUTS
PARAMETER
TEST LEVEL OR NOTES
(Note 7)
TYP
(Note 7)
UNITS
V
VIN
Differential Input Voltage Range
±0.5V /
REF
Gain
Input Voltage Range: Common Mode +
Signal
Gain = 1
A
A
+ 0.1
A
- 0.1
V
GND
VDD
Gain = 2, 4, 8, 16, 32, 64, 128
Gain = 1
+ 1.5
A
- 1.5
V
GND
VDD
Input Bias Current; AIN+, AIN-
300
3
nA
nA
nA
nA
Gain = 2, 4, 8, 16, 32, 64, 128
Gain = 1
Input Offset Current; AIN+, AIN-
±20
±1
Gain = 2, 4, 8, 16, 32, 64, 128
SYSTEM PERFORMANCE
Resolution
No Missing Codes
Gain = 1
24
Bits
INL
Integral Nonlinearity
±0.0002
±0.0004
±0.4
±0.001
% FSR
% FSR
Gain = 2 to 128
Gain = 1
Offset
ppm of
FS
Offset Drift
Gain = 1
±300
nV/°C
nV/°C
Gain = 2 to 128
±300/Gain
± 10
Full Scale Error
Full Scale Drift
Gain = 1
±0.007
±0.02
±0.1
±3.5
±3.5
110
%
%
Gain = 2 to 128
Gain = 1
ppm/°C
ppm/°C
ppm/°C
dB
Gain = 64
Gain = 128
Gain of 1
CMRR
PSRR
OWR
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Output Word Rate (Note 8)
85
Gain of 128
Gain of 1
130
dB
100
dB
Gain of 128
100
2.5
125
dB
4000
SPS
FN7608 Rev 0.00
October 12, 2012
Page 4 of 21
ISL26102, ISL26104
Electrical Specifications
V
+ = 5.0V, V
REF
- = 0V, A
VDD
= 5V, D = 5V XTALIN/CLOCK = 4.9152MHz (Note 6)
VDD
REF
T
= -40°C to +105°C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +105°C. (Continued)
A
MIN
MAX
SYMBOL
VOLTAGE REFERENCE INPUT
VREF Voltage Reference Input
VREF+ Positive Voltage Reference Input
PARAMETER
TEST LEVEL OR NOTES
(Note 7)
TYP
5.0
(Note 7)
UNITS
VREF = VREF+ - VREF-
1.5
A
+ 0.1
V
V
VDD
V
+ 1.5
A
+ 0.1
- 1.5
REF-
VDD
VREF-
VREFI
Negative Voltage Reference Input
Voltage Reference Input Current
A
- 0.1
V
V
GND
REF+
350
nA
Low-Side Power Switch
r
ON-resistance
10
ON
Continuous Current
30
mA
Power Supply Requirements
A
Analog Supply Voltage
Digital Supply Voltage
Analog Supply Current
4.75
2.7
5.0
5.0
6
5.25
5.25
10
V
VDD
D
V
VDD
A
Gain of 1
mA
mA
µA
µA
µA
µA
µA
µA
IDD
Gain = 2 to 128
Power-down
Standby
9
12
0.2
0.3
750
750
1
2.5
D
Digital Supply Current
Gain of 1
950
950
26
IDD
Gain = 2 to 128
Power-down
Standby
1.8
Power
Normal
Gain = 1
33.75
48.75
6
54.75
64.75
Gain = 2 to 128
Power-down
Standby
mW
µW
µW
10.5
Digital Inputs
V
0.7 D
VDD
V
V
IH
V
0.2 D
IL
VDD
V
I
I
= -1mA
= 1mA
D - 0.4
VDD
V
OH
OH
OL
V
0.2 D
V
OL
VDD
Input Leakage Current
±10
µA
MHz
MHz
External Clock Input Frequency
Serial Clock Input Frequency (Note 9)
0.3
4.9152
4
NOTES:
6. If the device is driven with an external clock, best performance will be achieved if the rise and fall times of the clock are slowed to less than 20ns
(10% to 90% rise/fall time).
7. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
8. Output word rates (MIN and MAX in the table) are specified using 4.9152MHz clock. If a different clock frequency is used, or if the internal oscillator
is used as the clock source for the converter, the output word rates will scale proportionally to the change in the clock frequency.
9. The OWR (Output Word Rate) setting dictates the rate at which the SDO/RDY signal will fall. To read every conversion word, reading of the conversion
word should begin immediately after SDO/RDY falls and the SCLK rate should be fast enough to read all 24 data bits of the conversion word before
the next falling edge of SDO/RDY that indicates that a new conversion word is available.
FN7608 Rev 0.00
October 12, 2012
Page 5 of 21
ISL26102, ISL26104
TABLE 1. INPUT REFERRED NOISE (nV, RMS)
PGA GAIN
OUTPUT WORD RATE
(Note 10)
1
2
4
8
16
32
64
128
6.5
2.5
187.1
101.8
112.2
133.0
157.7
207.1
264.6
292.7
368.2
405.5
517.0
52.0
25.0
14.5
8.8
6.6
5
209.2
253.6
308.3
417.7
55.9
28.5
16.3
10.5
8.4
8.2
10
63.8
35.5
20.0
13.9
11.9
15.7
23.3
31.6
35.4
46.2
50.6
64.1
72.6
90.2
101.0
112.4
124.3
134.0
147.6
162.3
178.0
196.0
11.6
15.2
22.4
30.1
34.3
45.2
49.5
62.5
70.5
87.4
20
77.6
43.8
25.0
18.1
25.3
40
105.1
140.1
159.4
203.0
222.2
284.5
318.1
398.0
445.0
489.5
557.0
632.0
708.8
801.0
891.0
955.1
60.2
35.1
80
100
547.2
78.2
46.8
34.9
607.0
87.5
52.2
39.7
160
780.3
845.1
1030.6
1169.0
1476.0
1632.0
1806.1
2018.0
2289.0
2572.5
2945.0
3287.0
3708.2
110.6
119.7
147.2
165.3
211.0
237.2
267.0
297.6
328.0
365.8
423.7
478.0
545.1
68.0
52.3
200
74.2
57.3
320
93.2
72.5
400
591.7
756.0
857.9
958.6
1089.0
1234.0
1380.4
1538.0
1711.0
1876.9
105.2
129.7
139.5
157.8
180.2
202.3
230.2
259.0
285.0
316.6
81.9
640
102.4
114.7
126.8
143.7
163.4
176.0
201.0
221.0
242.8
800
98.9
107.7
123.5
132.0
145.8
161.3
174.3
194.9
1000
1280
1600
2000
2560
3200
4000
NOTE:
4
10. The ADC has a programmable SINC filter. The -3dB bandwidth of the filter for a given word rate is 0.239 x OWR.
10000
1000
1X
100
10
1
2X
4X
8X
16X
32X
64X
128X
1
10
100
1000
10000
WORD RATE (Sps)
FIGURE 2. NOISE vs GAIN AND WORD RATE SETTINGS
FN7608 Rev 0.00
October 12, 2012
Page 6 of 21
ISL26102, ISL26104
TABLE 2. NOISE FREE BITS
NOISE-FREE BITS
OUTPUT WORD RATE
(Note 11)
1
2
4
8
16
32
64
128
19.8
19.5
19.0
18.6
18.0
17.6
17.4
17.0
16.9
16.5
16.4
16.0
15.9
15.7
15.5
15.5
15.3
15.2
15.1
14.9
2.5
21.9
21.8
21.5
21.2
20.8
20.4
20.3
19.9
19.8
19.5
19.3
19.0
18.8
18.7
18.5
18.3
18.2
18.0
17.8
17.6
21.8
21.7
21.4
21.2
20.8
20.4
20.3
20.0
19.8
19.5
19.3
18.9
18.8
18.6
18.4
18.2
18.1
17.9
17.8
17.6
21.8
21.7
21.5
21.2
20.8
20.4
20.2
19.8
19.7
19.3
19.2
18.9
18.7
18.6
18.4
18.2
18.0
17.9
17.7
17.6
21.9
21.7
21.3
21.0
20.6
20.2
20.0
19.7
19.6
19.3
19.1
18.8
18.6
18.4
18.3
18.1
18.0
17.8
17.6
17.4
21.6
21.5
21.2
20.9
20.4
19.9
19.8
19.4
19.3
19.0
18.8
18.5
18.4
18.2
18.0
17.8
17.7
17.5
17.3
17.2
21.4
21.1
20.7
20.3
19.8
19.4
19.2
18.8
18.7
18.3
18.1
17.8
17.7
17.5
17.3
17.1
17.0
16.8
16.7
16.6
20.8
20.4
19.9
19.5
19.0
18.5
18.4
18.0
17.8
17.5
17.3
17.0
16.8
16.7
16.5
16.4
16.3
16.2
16.0
15.9
5
10
20
40
80
100
160
200
320
400
640
800
1000
1280
1600
2000
2560
3200
4000
NOTE:
11. Noise-free resolution in Table 2 is calculated as LOG ((Input Span)/(RMS Noise x 6.6))/LOG(2). The result is rounded to the nearest tenth of a bit. The
Input Span is equivalent to ±0.5VREF/GAIN, V
= 5V. The RMS noise is selected from Table 1 for the desired Output Word Rate and Gain option.
REF
10
10000
8
6
4
2
0
NORMAL MODE
1000
NORMAL MODE, ALL PGA GAINS
100
10
POWERDOWN MODE
1
-40
-40
-10
20
50
80
110
-10
20
50
80
110
TEMPERATURE (°C)
TEMPERATURE (°C)
FIGURE 3. ANALOG CURRENT vs TEMPERATURE (GAIN = 2 TO 128)
FIGURE 4. DIGITAL CURRENT vs TEMPERATURE
FN7608 Rev 0.00
October 12, 2012
Page 7 of 21
ISL26102, ISL26104
Typical Characteristics
1000
100
10
1
100
10
1
0.1
1
10
100
1000
0.1
1
10
100
1000
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 5. NOISE SPECTRAL DENSITY, 4kSPS, PGA GAIN = 1
FIGURE 6. NOISE SPECTRAL DENSITY, 4kSPS, PGA GAIN = 128
1x
+
AIN1+
-
390
AIN2+
AIN1-
AIN2-
CAP
100nF
CAP
2x, 4x, 8x, 16x
32x, 64x, 128x
3RD ORDER
AVDD
PROGRAMMABLE
DIGITAL FILTER
SERIAL
PORT
MODULATOR
-
390
TEMP
SENSOR
+
1x
FIGURE 7. ISL26102 (2 CHANNEL) BLOCK DIAGRAM
FN7608 Rev 0.00
October 12, 2012
Page 8 of 21
ISL26102, ISL26104
Circuit Description
5.00
4.50
4.00
3.50
3.00
2.50
2.00
1.50
1.00
0.50
0.00
AIN-
A key element in the ISL26102/ISL26104 A/D converters is its
low noise chopper-stabilized programmable gain amplifier. The
amplifier features seven gain settings (2x, 4x, 8x, 16x, 32x, 64x,
and 128x). On these gain settings, the amplifier has very high
input impedance but has restricted common mode range, which
does not extend all the way to the power supply rails. When the
gain of 1x is selected, the chopper-stabilized amplifier is
bypassed. The modulator input, which is used directly in 1x gain,
has a common mode range that extends to the supply rails. But,
because of this greater common mode range on the 1x gain
setting, the input current is higher than on the other gain
settings.
AIN+
2.500
VCM
2.500
FIGURE 8. DIFFERENTIAL INPUT FOR V
= 5V, GAIN = 1X
REF
Digital Filter
The output of the delta-sigma modulator in the A/D converter is
filtered with a Sinc digital filter that includes programmable
The ISL26102 provides the user with two fully differential signal
inputs at the multiplexer plus two other internal channel
selections, which allow the user to monitor the analog supply
voltage of the chip, and the on-chip temperature sensor. The
ISL26104 provides the user with two additional fully differential
inputs on the multiplexer.
4
decimation to achieve a wide range of output word rates. The
4
transfer function of the Sinc filter is illustrated in Figure 9.
Figure 9 is normalized to 1 being the output word rate. The
output word rate can be selected by setting bits in the OWR
(Output Word Rate) Register. The converter provides a wide
selection of word rates as shown in Table 3. Note that the word
rates are based upon an XTALIN/CLOCK of 4.9152MHz. If the
clock is a different frequency than 4.9152MHz, the actual output
word rate will scale proportionally.
The programmable gain amplifier has a passive RC filter on its
output. The resistors are located inside the chip on the outputs of
the differential amplifier stages. The capacitor (nominally a
100nF C0G ceramic or PPS film (Polyphenylene sulfide)) for the
filter is connected to the two CAP pins of the chip. The outputs of
the differential amplifier stages of the PGA are filtered before
their signals are presented to the delta-sigma modulator. This
filter reduces the amount of noise by limiting the signal
bandwidth and eliminating the chopping artifacts of the chopped
PGA stage.
TABLE 3. OUTPUT WORD RATE REGISTER SETTINGS
DATA RATE (Sps)
2.5
REGISTER CODE (Hex)
00
01
02
03
04
05
0B
06
0C
07
0D
08
0E
11
09
0F
12
0A
10
13
5
Figure 7 illustrates a block diagram of the programmable gain
amplifier.
10
20
Functional Description
Analog Input Span
40
80
100
The input span of the A/D converter is determined by the
magnitude of the voltage reference and the gain setting
selection. The voltage reference magnitude is determined by the
voltage difference between the VREF+ and the VREF- pins. This
voltage may be as low as 1.5V or as great as the analog supply
voltage to the chip. The voltage on the VREF pins is scaled to accept
a voltage into the A/D converter on 1x gain of ±0.5 VREF/GAIN
where gain is 1. An illustration of the input span when using a 5V
160
200
320
400
640
V
is in Figure 8. The figure illustrates that with a V = 5V and a
REF
REF
800
gain setting of 1x, the input span will be ±2.5V, which is a fully
differential signal. If the programmable gain amplifier gain is set to
another value other than 1x, the input span will be reduced by the
1000
1280
1600
2000
2560
3200
4000
gain scale factor. With a V
= 5V and the PGA gain set at 128x,
REF
the input span into the ADC will be [±(0.5)5V]/128 = ±19.53mV on
a fully differential basis.
FN7608 Rev 0.00
October 12, 2012
Page 9 of 21
ISL26102, ISL26104
0
-20
CRYSTAL
XTALIN/
CLOCK
OSCILLATOR
-40
CLOCK DETECT
-60
-80
EN
INTERNAL
-100
-120
-140
-160
-180
OSCILLATOR
XTALOUT
MUX
TO ADC
-200
0.10
1.00
10.00
FIGURE 10. CLOCK GENERATOR BLOCK DIAGRAM
NORMALIZED FREQUENCY (1.00 = OWR)
4
Overview of Registers and A/D Converter
Operation
FIGURE 9. TRANSFER FUNCTION OF SINC NORMALIZED TO
1 = OUTPUT WORD RATE
The ISL26102, ISL26104 devices are controlled via their serial
port by accessing various on-chip registers. Communication to
the A/D via the serial port occurs by writing a command byte
followed by a data byte. All registers in the converter are
accessed or written as 8-bit wide registers, even though some
data words may be up to three bytes in length. The converter has
offset registers (three bytes wide) associated with each PGA gain
setting. These registers hold the offset calibration word, a three
byte twos complement word, for each gain selection. When
power is first applied to the converter these registers are reset to
zero. Note that the ISL26102, ISL26104 converters do not have
gain calibration registers for the PGA gains. This is because the
gain for each PGA gain setting is calibrated at the factory.
Digital Filter Settling Time
If the Input Mux Selection register is written into to select a new
channel, the modulator and the digital filter are reset and the
converter begins computing a new output word when the new
mux selection is made. The first conversion word output from the
A/D after a new mux channel is selected, or after the PGA gain is
4
changed, will be delayed to allow the filter to fully settle. A Sinc
filter takes four conversion times to fully settle, therefore the
SDO/RDY signal will not fall until a time of four normal
conversion periods has elapsed. The SDO/RDY output falls to
signal that an output conversion word is ready to be read.
Whenever the input signal has a large step change in value, it
may take as many as six output conversions for the output word
to accurately represent the new input value.
Table 4 list the registers inside the ADC. When power is first
applied the Offset Array Registers, registers which hold the offset
calibration words for each PGA gain, are set to zero.
Clock Sources
The Chip ID register has a bit, which allows the user to identify
whether the chip is an ISL26102 (2 channel) or an ISL26104
(4 Channel) device. This register also has a code, which is
assigned to reveal the revision of the chip.
The ISL26102/ISL26104 can operate from an internal oscillator,
and external clock source, or from a crystal connected between
the XTALIN/CLOCK and XTALOUT pins. See the block diagram for
the clock system in Figure 10. When the converter is powered up,
the CLOCK DETECT block determines if an external clock source
is present. If a clock signal greater than 300kHz is present on the
XTALIN/CLOCK pin, the circuitry will disable the internal oscillator
and use the external clock as the clock to drive the chip circuitry.
If the ADC is to be operated from the internal oscillator the
XTALIN/CLOCK pin should be grounded. If the ADC is to be
driven with an external clock there should be a 100 resistor
placed in series with the clock signal to the XTALIN/CLOCK pin.
This helps slow the rise and fall time edges, which can impact
converter performance. If the ADC is to be operated with a
crystal, the crystal should be located very close to the A/D
converter package pins. Note that loading capacitors for the
crystal are not required as there are loading capacitors built into
the silicon, although the capacitor values are optimized for
operation with a 4.9152MHz crystal.
The SDO/LSPS register allows the user to control the behavior of
the SDO (Serial Data Output) output. If bit (b1) is set to logic 0,
the SDO/RDY output will go low when conversions are completed
and output the 24-bit conversion word if CS is taken high and 24
SCLKs are issued to the SCLK pin. If the SDO bit in this register is
set to logic 1, the SDO output will be set to a tri-state condition
(high output impedance). This allows another device, such as
another A/D converter, to be connected to this same signal line
going to the microcontroller.
The LSPS (Low-Side Power Switch) bit allows the user to toggle a
switch via the LSPS pin that can be used to enable power to a
load cell or other circuitry. When the LSPS bit is logic 0 the LSPS
switch is open. When the LSPS bit is logic 1, the switch is closed.
The LSPS bit is set back to a logic 0 if the chip is put into Standby
via the Standby Register, or if the PDWN signal is activated. See
data sheet tables for the current capability of the switch.
The Standby register has a bit which when set to logic 1, the chip
enters the standby mode. In standby mode, the chip enters a low
power state. Only the crystal oscillator is left powered (if used) to
enable a quick return to full operation when bit (b0) is set back to
logic 0. If the crystal is not being used, it is not powered. In this
FN7608 Rev 0.00
October 12, 2012
Page 10 of 21
ISL26102, ISL26104
case, there is no difference in power consumption for standby or
power-down modes.
If the b1b0 bits are set to 10, conversions will be performed
continuously until bits b1b0 are set to either 00 or 01, Standby
mode is activated, or the PDWN pin is taken low. Refer to
“Reading Conversion Data” on page 14.
The Output Word Rate register allows the user to set the rate at
which the converter performs conversions. Table 3 lists the
output word rate options.
The Delay Timer register allows the user to program a delay time,
which will be inserted between the time that the user selects an
input to be converted via the Input Mux Selection register and
when the conversion is started. If continuous conversions are
selected via the Conversion Control register, the Input Mux
Selection register can be changed without needing to stop
conversions. The Delay Timer register allows the user to insert a
delay between when the mux is changed and when a new
conversion is started. If the Delay Timer register is set to all 0's
the minimum delay will be 100µs.
The Input Mux Selection register defines the input signal that will
be used when conversions are performed. The signals include
either 2 (ISL26102) or 4 (ISL26104) differential input channels,
an on-chip temperature sensor, or the monitor node for the AVDD
supply voltage. Note that if the temperature sensor or the AVDD
monitor are selected the PGA gain is internally set for 1x gain.
The PGA Gain register allows the user to set the PGA gain setting
for the channel pointed to by the Channel Pointer register. The
PGA provides gain settings of 1x (in this gain setting the
programmable gain amplifier is actually bypassed and the signal
goes directly to the modulator), 2x, 4x, 8x, 16x, 32x, 64x, and
128x.
Any time the PGA Gain setting is changed, the channel selection
is changed, or a command is given to start conversion(s), the
user can expect a delay before the SDO/RDY signal will fall. This
delay is defined by Equation 1:
The Conversion Control register provides the means to initiate
offset calibration, or initiate single or continuous conversions. If
bit b2 of this register is set to a logic 1, an offset calibration will
be performed and the states of bits b1 and b0 are ignored. The
state of bit b2 will be set back to a logic 0 after the offset
calibration is complete.
4ms + Delay Timer Register Setting 4ms + 100s + 4 1 OWR
(EQ. 1)
The first 4ms is for the PGA to settle. This delay cannot be
changed. The Delay Timer register setting is user controllable,
and it dictates the majority of the second section of the equation.
The 4*(1/OWR) term is the time required for the filter to settle at
the OWR (Output Word Rate), which has been selected in the
Output Word Rate register.
If the b1b0 bits are set to 01, a single conversion will be
performed. When the conversion is completed, the bits will be set
back to 00, the SDO/RDY pin will be taken low (note that the CS
pin must be a logic 1 for SDO/RDY to fall) and the conversion
data will be held in a register. If the user enables CS (held at
logic 1) and provides 24 SCLKs to the SCLK pin, the data word
will be shifted out of the SDO/RDY pin as a 24-bit two’s
complement word, starting with the MSB. Data bits are clocked
out on the rising edge of SCLK. If the entire 24-bit data word is
not read before the completion of the next conversion, it will be
overwritten with the new conversion word.
The PGA Offset Array registers hold the calibration results for the
offset calibration done for each of the PGA gain settings. The
result of an offset calibration is a 24-bit twos complement word.
There are eight high byte registers, eight mid byte registers and
eight low byte registers. When reading or writing to one of the
PGA Offset Array byte registers, the register selected will be
determined by the PGA Pointer Register.
The PGA Pointer register contains the pointer to the PGA Offset
register array bytes associated with a specific PGA gain.
FN7608 Rev 0.00
October 12, 2012
Page 11 of 21
ISL26102, ISL26104
TABLE 4. CONTROL REGISTERS
NAME
ADDRESS
DATA BITS
NOTES
Write Read b7 b6 b5 b4 b3 b2 b1 b0
Registers are Accessed by Address Byte followed by Register Data Byte
Chip ID
N/A
82h
00h b4
0 = ISL26104
1 = ISL26102
b3-b0
Revision Code
SDO/LSPS
Standby
02h b1
1= Disable SDO
0 = Enable SDO
b0
1 = LSPS ON
0 = LSPS OFF
0 is default
0 is default
83h
03h b0
1 = Enable Standby
0 = Disable
0 is default
Output Word 85h
Rate
05h See Table 3 on page 9
0 is default, 2.5Sps
Input Mux
Selection
87h
07h ISL26104
b2 b1 b0
000 = Channel 1
001 = Channel 2
010 = Channel 3
011 = Channel 4
100 = Analog Supply Monitor
101 = Temperature Sensor
110 = Not used
111 = Not used
ISL26102
b2 b1 b0
000 = Channel 1
001 = Channel 2
010 = Analog Supply Monitor
011 = Temperature Sensor
100 = Not used
101 = Not used
110 = Not used
111 = Not used
Channel
Pointer
88h
08h ISL26104
b2 b1 b0
000 = Channel 1
001 = Channel 2
010 = Channel 3
011 = Channel 4
100 = Analog Supply Monitor
101 = Temperature Sensor
110 = Not used
111 = Not used
ISL26102
b2 b1 b0
000 = Channel 1
001 = Channel 2
010 = Analog Supply Monitor
011 = Temperature Sensor
100 = Not used
101 = Not used
110 = Not used
111 = Not used
FN7608 Rev 0.00
October 12, 2012
Page 12 of 21
ISL26102, ISL26104
TABLE 4. CONTROL REGISTERS (Continued)
DATA BITS
NAME
ADDRESS
97h 17h b2 b1 b0
NOTES
PGA Gain
PGA Gain Setting for Channel Pointed to by the Channel Pointer Register.
Whenever the Analog Supply Monitor or the Temp Sensor are selected, the PGA
gain is set to 1x.
000 = 1x
001 = 2x
010 = 4x
011 = 8x
100 = 16x
101 = 32x
110 = 64x
111 = 128x
Conversion
Control
84h
04h b2
0 = Off
Performing Offset Calibration has priority over instructions from bits b1b0
1 = Perform Offset Calibration
b1 b0
00 = Stop Conversions
01 = Perform Single Conversion
10 = Perform Continuous Conversions
11 = Not Used
Delay Timer
C2h
BDh
42h b7-b0 The start of conversion is delayed
by: Delay = Register Word*4ms + 100µs
PGA Offset
Array
3Dh Offset Calibration Result
Most Significant Byte
For PGA Pointed to by PGA Pointer Register
(High Byte)
PGA Offset
Array
(Mid Byte)
BEh
BFh
3Eh Offset Calibration Result
Middle Byte
For PGA Pointed to by PGA Pointer Register
PGA Offset
Array
3Fh Offset Calibration Result
Low Byte
For Channel Pointed to by Channel Pointer Register
(Low Byte)
PGA Monitor Bch
3ch b2 b1 b0
000 = 1x
This register points to the offset register associated with the PGA gain selection
001 = 2x
010 = 4x
011 = 8x
100 = 16x
101 = 32x
110 = 64x
111 = 128x
See Figure 11 for an illustration of the timing to write on-chip
registers.
Writing to On-chip Registers
Writing into a register on the chip involves writing an address
byte followed by a data byte. The lead bit of the address byte is
always a logic 1 to indicate that data is to be written. The
remaining seven bits of the address byte contain the address of
the register that is to be written. To begin the write cycle, CS must
first be taken low with SCLK low. This should occur at least
If multiple registers are to be written, CS should be taken high
after each address byte/data byte combination and remain high
for at least a period of time equal to 6*1/(Xtal/Clock) frequency.
If the chip is operating from a 4.9152MHz master clock, this
would mean that CS should remain high between write cycles for
at least 6*1/4.9152MHz = 1.22µs.
125ns before SCLK goes high. This is shown as t in the timing
cs
diagram of Figure 11. Once CS is low, the user must then present
the lead bit to the SDI port. The data bits will be latched into the
Lower frequency master clock rates (minimum master clock rate
can be as low as 300kHz) will require CS to remain high for a
longer period of time between register write cycles.
port by rising edges of SCLK. The data set-up time (t ) of the
ds
data bits to the rising edge of SCLK is 50ns (Note that one half
clock cycle of the highest SCLK rate is 1/(2*4 MHz) = 125ns).
Each time an address/data byte combination is written into the
port, the master clock is used to place the data into the register
after CS returns high. This is required because the data transfer
must be synchronized to the clock that is driving the
modulator/filter circuitry.
Data hold time (t ) is also 50ns. Data bits should be advanced
dh
to the next bit on falling edges of SCLK. Once the eight data bits
have been written, CS should be returned to high. (CS must be
high to read conversion data words from the port). When CS goes
high the user should ignore any activity on the SDO/RDY pin for
at least 10 cycles of the master clock, which is driving the ADC.
FN7608 Rev 0.00
October 12, 2012
Page 13 of 21
ISL26102, ISL26104
will then wait for the SDO/RDY signal to fall. Once the SDO/RDY
signal falls, the 24-bit conversion data word becomes available to
the port. To read the conversion word, the CS signal should be left
in the logic 1 state and 24 SCLKs issued to the SCLK pin. The first
rising SCLK edge will make the MSB data bit of the 24-bit word
become available. The falling edge of the first SCLK will latch the
bit into the external receiving logic device. Subsequent rising
edges of SCLK will cause the port output to advance to the next
data bit. Once the last data bit is read, the SCLK signal should
remain low until another conversion word is available or until a
command to write or read an on-chip register is performed.
Reading from On-chip Registers
Reading from a register on the chip begins by writing an address
byte into the SDI port. The lead bit of the address byte is always a
logic 0 to indicate that data is to be read from an on-chip register.
The remaining seven bits of the address byte contains the
address of the register that is to be read. To begin the read cycle,
CS must first be taken low with SCLK low and be low for at least
125ns before SCLK is taken high to latch the first data bit. The
eight address bits will be latched into the port by rising edges of
SCLK. The data set-up time (t ) of the data bits to the rising edge
ds
of SCLK is 50ns (one half clock cycle of the highest SCLK rate is
1/(2*4MHz) = 125ns). Data hold time (t ) is also 50ns. Address
SDO/RDY goes low to signal that a conversion has been
performed and that the conversion word is available. If the
analog input signal goes over range this may cause the
modulator to become unstable. If this condition occurs the
modulator resets itself. The output code will be held at full scale
but the effect of the modulator being reset will cause the
SDO/RDY signal to fall at only one fourth of its word rate. This
occurs because when the modulator is reset, the digital filter is
also reset and it takes four conversion periods for the filter to
accumulate enough modulator bit stream information to produce
an accurate conversion result.
dh
bits should be advanced to the next bit on falling edges of SCLK.
Once the address byte has been written, the port will output a
byte from the selected 8-bit register onto the SDO pin. A total of
16 SCLKs are required to write the address byte and then read
the 8-bit register output. The timing for reading from on-chip
registers is illustrated in Figure 12.
Reading Conversion Data
Reading conversion data is done in a different manner than
when reading on-chip registers. After writing into the Conversion
Control register to instruct the A/D to start conversions, the user
CS
t
t
sc
cs
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
SCLK
t
t
ds dh
A
6
A
5
A
4
A
3
A
2
A
1
A
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
SDI
W
DON’T CARE
DON’T CARE
FIGURE 11. WRITE ON-CHIP REGISTER WAVEFORMS
CS
t
t
sc
cs
t
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
SCLK
SDI
t
DON’T CARE
ds dh
R
X
X
A
6
A
5
A
4
A
3
A
2
A
1
A
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Q
7
Q
6
Q
5
Q
4
Q
3
Q
2
Q
1
Q
0
X
X
XX (DON’T CARE)
SDO
FIGURE 12. READ ON-CHIP REGISTER WAVEFORMS
CS
DATA READY
DATA
NEW DATA READY
MSB
LSB
2
3
2
2
2
1
0
SDO/RDY
SCLK
1
2
3
4
2
4
FIGURE 13. READING CONVERSION DATA WORD WAVEFORMS
FN7608 Rev 0.00
October 12, 2012
Page 14 of 21
ISL26102, ISL26104
Output Data Format
DVDD
The converter outputs data in twos complement format in
accordance with coding shown in Table 5.
TABLE 5. OUTPUT CODES CORRESPONDING TO INPUT
1kΩ
INPUT SIGNAL
+ 0.5V /GAIN
DESCRIPTION
+ Over-range
+ 1 LSB
OUTPUT CODE (HEX)
7FFFFF
CONNECT TO
PDWN PIN
REF
2.2nF
23
0.5V
0
/[GAIN*(2 - 1)]
000001
REF
FIGURE 14. PDWN DELAY CIRCUIT
Zero Input
- 1 LSB
000000
23
-0.5V
/[GAIN*(2 -1)]
FFFFFF
REF
Standby Mode Operation
- 0.5V
/GAIN
REF
- Over-range
800000
The A/D converter can be placed in the standby mode by writing
to the Standby register. Standby mode causes the converter to
enter a low power state except for the crystal oscillator amplifier.
If the converter is operated with a crystal connected to the
XTALIN/CLOCK and XTALOUT pins the crystal will continue to
oscillate. This reduces start-up time when the Standby register
bit is written back to logic 0 to exit standby mode.
Operation of PDWN
When power is first applied to the converter, the PDWN pin must
transition from Low to High after both power supplies have
settled to specified levels in order to initiate a correct internal
power-on reset. A means of controlling the PDWN pin with a
simple RC delay circuit is illustrated in Figure 14. If AVDD and
DVDD are different supplies, be certain that AVDD is fully
established before PDWN goes high.
Low Side Power Switch
The ADC includes a low side power switch. The LSPS pin is an
open drain connection to a transistor, which can be turned on or
off via bit control in the SDO/LSPS register. The LSPS switch can
be used to enable/disable excitation to external systems, such as
a load cell. Figure 15 illustrates the typical connection of the ADC
in a load cell measurement system. The LSPS pin is connected to
the low side of the load cell.
The PDWN pin can be taken low at any time to reduce power
consumption. When PDWN is taken low, all circuitry is shut
down, including the crystal oscillator. When coming out of
power-down, PDWN is brought high to resume operation. There
will be some delay before the chip begins operation. The delay
will depend upon the source of the clock being used. If the
XTALIN/CLOCK pin is driven by an external clock, the delay will be
minimal. If the crystal oscillator is the clock source, the oscillator
must start before the chip can function. Using the on chip crystal
oscillator amplifier with an attached 4.9152MHz clock will
typically require about 20ms to start-up.
5V
3.3V
0.1µF
18
1
6
DVDD
AVDD
16
9
VREF+
CAP
GAIN = 128
24
SDO/RDY
0.1µF
10
23
21
SCLK
SDI
CAP
-
+
ISL26102
20
22
MICRO
CONTROLLER
CS
PDWN
11
12
AIN1+
AIN1-
AIN2+
AIN2-
4
3
XTALOUT
13
14
15
19
XTALIN/CLOCK
VREF-
LSPS
AGND
17
DGND
2, 5, 7, 8
FIGURE 15. A LOAD CELL MEASUREMENT APPLICATION USING THE ISL26102
FN7608 Rev 0.00
October 12, 2012
Page 15 of 21
ISL26102, ISL26104
23
)/2 = 298nV. Since the converter
span is bipolar, and its span represents ± 8.338 million codes,
the +111.7mV will output of a code of approximately 374,800
counts.
converter will be ±0.5(V
REF
Device Supply and Temperature Monitoring
One of the multiplexer input selections is the AVDD Monitor. This
option allows the A/D converter to measure a divided down value
of the AVDD voltage. The nominal output code from AVDD
23
monitor is given by (2 )*AVDD/(2*VREF). Table 6 provides a
The on-chip temperature will typically be about 3° hotter than
ambient because the device's power consumption is about
50 mW and the thermal impedance from die to ambient is about
63°/W; (0.05)*63 = 3.15°.
listing of the nominal count of the A/D converter associated with
supply voltage values between 4.75 and 5.25V. Table 6 is based
on V
= 5V.
REF
If a V
REF
of 2.5V is used, the output code from the A/D converter
Getting Started
will stay at +Full Scale when AVDD > 5V. Thus, the AVDD monitor
will not be able to check the voltages greater than 5V, but it will
provide proper readings for AVDD voltages below 5V.
When power is first applied to the converter, the PDWN pin
should be held low until the power supplies and the voltage
reference are stable. Then PDWN should be taken high. When
this occurs the serial port logic and other logic in the chip will
have been reset. The chip contains factory calibration data stored
in on-chip non-volatile memory. When PDWN goes positive this
data is transferred into the appropriate working registers. This
initialization can take up to 12.6ms. If an external clock or the
internal oscillator are used as the clock for the chip, then this
12.6ms time includes the time necessary for these to be
functional. But, if the crystal oscillator is used, the crystal may
take 20ms to start up before the 12.6ms initialization occurs.
Writing into or reading from the serial port should be delayed
until the clock source and the initialization period have elapsed.
TABLE 6. ANALOG SUPPLY MONITOR OUTPUT CODES OVER SUPPLY
VOLTAGES (V
= 5.0V)
REF
AVDD
(V)
OUTPUT CODE
(±5%)
5.25
5.10
5.00
4.90
4.75
4407063
4281464
4197996
4114662
3989915
Once the clock source and initialization period have elapsed, the
user should configure the ADC by writing into the appropriate
registers. The commands and the corresponding data bytes that
are to be placed into each of the registers are shifted into the SDI
pin with CS held low. CS should be taken high for at least six
cycles of the master clock after each command/data byte
combination. This allows the control logic to properly synchronize
the writing of the register with the master clock that controls the
modulator/filter system. Each command/data byte combination
should have its own CS cycle of CS going low, shifting the data,
then CS going high, and remaining high for at least six cycles of
the master clock.
+
TO BUFFER/PGA
24-BIT ADC
AIN1 +
-
AIN1 -
AIN2 +
AIN2 -
AIN3 +
AIN3 -
AIN4 +
AIN4 -
TEMP
Even though the device has been powered up, reset, and its
register settings have been configured, the programmable gain
amplifier and modulator portions of the ADC remain in a low
power state until a command to start conversions is written into
the Conversion Control register. To minimize drift in the device
due to self-heating, it is recommended that after all registers are
initialized to their initial condition, the command to start
continuous conversions be issued as soon as is practical.
Subsequent changes to registers, such as selecting another mux
channel, should be performed with continuous conversions
active. The proper method of writing to the other registers when
continuous conversions are active is to wait for SDO/RDY to fall,
read the conversion data, then take CS low and issue the
command and the data byte that is to be written into a register,
then return CS high. If multiple registers are to be written, CS
should be toggled low and high to frame each command/data
byte combination. Whenever any of the following registers
[SDO/LSPS, Output Word Rate, Input Mux Selection, PGA Gain,
Delay Timer, PGA Offset Array, or Offset Calibration] are written
with continuous conversions in progress, the digital filter will be
reset and there will be a delay determined by Equation 1 on
page 11. The delay will begin when CS returns and remains high.
When the delay has elapsed, the SDO/RDY signal will go low to
SENSOR
AVDD
FIGURE 16. INPUT MULTIPLEXER BLOCK DIAGRAM
When the Input Mux Selection register is instructed to select the
on-chip temperature sensor signal, the A/D measures a
differential voltage produced between two diodes that are biased
at different operating currents. The differential voltage is defined
by Equation 2:
(EQ. 2)
V = 102.2 mV + (379µV* T(°C))
Whenever the temperature sensor is selected in the Input Mux
Selection Register, the Gain is set to 1x.
At a temperature of +25°C the measured voltage will be
approximately 111.7mV. The actual output code from the
converter will depend upon the magnitude of the VREF signal.
The 111.7mV signal will be a portion of the span set by the VREF
voltage using a gain setting of 1x. If V
is 5V, one code in the
REF
FN7608 Rev 0.00
October 12, 2012
Page 16 of 21
ISL26102, ISL26104
signal that a conversion data word is available. The Chip ID
register (read only), the Channel Pointer register, and the PGA
Monitor register can be read or written without any effect to the
filter, and therefore there will be no delay in SDO/RDY falling. If
the Standby register is enabled, conversions will be stopped.
in the PGA Offset Arrays. Some user applications prefer to calibrate
their system in the factory, then off load the calibration data and
write it into non-volatile memory. Then when the product is powered
up, this data is written back into the registers of the ADC.
1. Write into the PGA Pointer register (BCh) the selection wanted
for the Gain of the PGA.
Performing Calibration
2. Read the three different PGA Offset Array registers, High byte
(3Dh), Mid byte(3Eh), and Low byte(3Fh). Note that they can
be read in any order, just understand that the three bytes
represent a two's complement 24-bit word with the byte in
order, high, mid and low.
The offset calibration function in the A/D converter removes the
offset associated with the PGA (Programmable Gain Amplifier) in
a specific gain setting. There are eight gain settings (1x, 2x, 4x,
8x, 16x, 32x, 64x, and 128x) and there is an array of eight sets of
three byte registers which hold the high, middle, and low bytes of
a 24-bit calibration word. The word is stored in twos complement
format.
Write Offset Calibration Registers
Upon power-up the offset registers are initialized to zero. After an
offset calibration is performed the registers associated with that
selected PGA gain will contain a valid 24-bit two's complement
number.
When calibration is performed it is to correct the PGA offset and is
not actually associated with a given input channel. When a
calibration is executed, its result is based upon the results of the
converter performing a conversion with the input to the PGA shorted
internally to the chip. The conversion result will have an uncertainty
due to the peak-to-peak noise of the converter on the word rate in
which the calibration is performed. Lower word rates have lower
signal bandwidth and therefore will have less peak to peak variation
in the output result when a calibration is performed. Therefore, it
can improve calibration accuracy if the calibration is performed with
the lowest word rate acceptable to the user.
This number can be saved into non-volatile memory and then
written back to the PGA Offset Array register.
1. Write into the PGA Pointer register (BCh) the selection for the
Gain setting of the PGA for which offset data is to be written.
2. Write the three different PGA Offset Array registers, High byte
(BDh), Mid byte (BEh), and Low byte (BFh). Note that they can
be written in any order, just understand that the three bytes
represent a two's complement 24-bit word with the byte in
order, high, mid and low.
Perform a PGA Offset Calibration
1. Write to the Output Word Rate register (85h) and select a
word rate.
The value written will be subtracted from the conversion data before
it is output from the converter whenever that particular PGA Gain
setting is used. Offset values up to the equivalent of full scale of the
converter can be written but realize that this can consume dynamic
range for the actual signal if the offset value is set to a large
number.
2. Write to the Input Mux Selection register (87h) and select an
input channel (AIN1 to AIN4, not AVDD monitor or
Temperature Sensor). Note that the channel will actually be
shorted internally so it need not be a specific channel.
3. Write to the Channel Pointer register (88h) with the same
selection written into the Mux Selection register.
Example Command Sequence
Table 7 illustrates an example command sequence to set up the
ADC once power supplies are active. The sequence of commands,
Set Channel Pointer, Set PGA Gain Setting, Set Mux Selection, Set
Data Rate, and Start Continuous Conversions, can be written into
the ADC as a sequence, each framed with CS going low at the
beginning of each command and returning high at the end of the
associated data byte (the rising edge of CS is the signal that actually
writes the data byte to the control register). After continuous
conversions are started, it is best if a time delay occur before the
Perform Offset Calibration is issued. There is no specific amount of
delay time as this depends upon the gain selection and the accuracy
required. When the command to perform the offset calibration is
issued, the continuous conversions in progress will be paused and
the conversion sequence will be performed as necessary to perform
the calibration. Once the calibration is completed, continuous
conversions will be automatically restarted. Any subsequent
commands which write into registers [SDO/LSPS, Output Word
Rate, Input Mux Selection, PGA Gain, Delay Timer, PGA Offset Array,
or Offset Calibration] while continuous conversions are in
progress will reset the digital filter and introduce a delay
determined by Equation 1 on page 11, after which, the SDO/RDY
signal will toggle low to signal the availability of a conversion
word.
4. Write the PGA gain selection into the PGA Gain register (97h).
5. Write bits b1 and b0 of the Conversion Control Register (84h)
setting b1 to logic 1 and bit b2 to logic 0 to Perform
Continuous Conversions.
6. Allow some delay and then write bit b2 of the Conversion Control
Register (84h) to logic 1 to start the calibration process. The
calibration time will be a function of the selection made in the
Output Word Rate register. To determine when the calibration
cycle is completed the user has two options. One is to monitor
SDO/RDY for a falling edge as this signals the completion of
conversion. A second approach would be to introduce a wait
timer for at least the period of five conversion times at the word
rate selected. [Example: If the word rate is 10Sps the calibration
should be completed at 5x 1/10s or 500ms. After this time, the
microcontroller can poll bit 2 of the Conversion Control Register.
Bit b2 will be set back to logic 0 when the calibration has
completed. It is best not to pollthe register continuously because
the added activity on the serial port may introduce noise and
impact the calibration result.
Read Offset Calibration Registers
After an offset calibration has been performed, the calibration
result, which is a 24-bit (3 bytes) two's complement word, is stored
FN7608 Rev 0.00
October 12, 2012
Page 17 of 21
ISL26102, ISL26104
TABLE 7. EXAMPLE COMMAND SEQUENCE
ADDRESS
OPERATION
Set Channel Pointer
Set PGA Gain Setting
REGISTER
Channel Pointer
PGA Gain
(WRITE)
DATA
COMMENTS
88h
01h
Set to select channel 2 (AIN2+, AIN2-)
97h
06h
Sets PGA gain to 64x. This PGA gain is applied to the signal channel pointed
to by the Channel Pointer set above.
Set Mux Selection
Input Mux Selection
87h
00h
Mux selection determines which channel is connected to the ADC. This step
selects mux input 1 (AIN1+, AIN1-).
Set Data Rate
OWR
85h
84h
11h
02h
Sets output word rate to 1kSps. See Table 3 for other data rate options.
Start Continuous
Conversions
Conversion Control
Set bits (b1-b0) of the Conversion Control register to ‘10’ to start continuous
conversions.
Perform Offset
Calibration
Conversion Control
Input Mux Selection
84h
87h
04h
01h
Set bit (b2) of the Conversion Control register to 1 to initiate an offset
calibration of the PGA gain setting selected above. Note that bit (b3) will return
to 0 when the calibration is completed.
Set Mux Selection
Mux selection determines which channel is connected to the ADC. This step
selects mux input 2 (AIN2+, AIN2-).
FN7608 Rev 0.00
October 12, 2012
Page 18 of 21
ISL26102, ISL26104
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest revision.
DATE
REVISION
FN7608.0
CHANGE
October 12, 2012
Initial release.
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
For a complete listing of Applications, Related Documentation and Related Parts, please see the respective product information page.
Also, please check the product information page to ensure that you have the most updated datasheet: ISL26102, ISL26104
To report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff
FITs are available from our website at http://rel.intersil.com/reports/search.php
© Copyright Intersil Americas LLC 2012. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7608 Rev 0.00
October 12, 2012
Page 19 of 21
ISL26102, ISL26104
Package Outline Drawing
M24.173
24 LEAD THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP)
Rev 1, 5/10
A
1
3
7.80 ±0.10
SEE DETAIL "X"
13
24
6.40
PIN #1
I.D. MARK
4.40 ±0.10
2
3
0.20 C B A
1
12
+0.05
-0.06
0.15
B
0.65
TOP VIEW
END VIEW
1.00 REF
H
-
0.05
C
+0.15
-0.10
0.90
1.20 MAX
GAUGE
PLANE
SEATING PLANE
0.10 C
0.25
+0.05
-0.06
C B A
0.25
0.10
5
0°-8°
0.60± 0.15
0.05 MIN
0.15 MAX
M
SIDE VIEW
DETAIL "X"
(1.45)
NOTES:
1. Dimension does not include mold flash, protrusions or gate burrs.
Mold flash, protrusions or gate burrs shall not exceed 0.15 per side.
2. Dimension does not include interlead flash or protrusion. Interlead
flash or protrusion shall not exceed 0.25 per side.
3. Dimensions are measured at datum plane H.
(5.65)
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
5. Dimension does not include dambar protrusion. Allowable protrusion
shall be 0.08mm total in excess of dimension at maximum material
condition. Minimum space between protrusion and adjacent lead
is 0.07mm.
(0.65 TYP)
(0.35 TYP)
6. Dimension in ( ) are for reference only.
TYPICAL RECOMMENDED LAND PATTERN
7. Conforms to JEDEC MO-153.
FN7608 Rev 0.00
October 12, 2012
Page 20 of 21
ISL26102, ISL26104
Package Outline Drawing
M28.173
28 LEAD THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP)
Rev 1, 5/10
A
1
3
9.70± 0.10
SEE DETAIL "X"
15
28
6.40
PIN #1
I.D. MARK
4.40 ± 0.10
2
3
0.20 C B A
1
14
+0.05
-0.06
0.15
B
0.65
TOP VIEW
END VIEW
1.00 REF
H
-
0.05
+0.15
-0.10
0.90
C
GAUGE
PLANE
1.20 MAX
0.25
SEATING PLANE
0.10 C
+0.05
-0.06
0.25
0.10
0°-8°
0.60 ±0.15
5
0.05 MIN
0.15 MAX
C B A
M
SIDE VIEW
DETAIL "X"
(1.45)
NOTES:
1. Dimension does not include mold flash, protrusions or gate burrs.
Mold flash, protrusions or gate burrs shall not exceed 0.15 per side.
2. Dimension does not include interlead flash or protrusion. Interlead
flash or protrusion shall not exceed 0.25 per side.
3. Dimensions are measured at datum plane H.
(5.65)
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
5. Dimension does not include dambar protrusion. Allowable protrusion
shall be 0.08mm total in excess of dimension at maximum material
condition. Minimum space between protrusion and adjacent lead
is 0.07mm.
(0.35 TYP)
(0.65 TYP)
TYPICAL RECOMMENDED LAND PATTERN
6. Dimension in ( ) are for reference only.
7. Conforms to JEDEC MO-153.
FN7608 Rev 0.00
October 12, 2012
Page 21 of 21
相关型号：
ISL26104AVZ-T7
4-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO28, ROHS COMPLIANT, PLASTIC, MO-153, TSSOP-28
RENESAS
ISL26104AVZ-T7A
Low-Noise 24-bit Delta Sigma ADC; TSSOP28; Temp Range: -40° to 105°C
RENESAS
©2020 ICPDF网 联系我们和版权申明