ISL89160FRTBZ [RENESAS]
High Speed, Dual Channel, 6A, 4.5 to 16VOUT, Power MOSFET Drivers;型号: | ISL89160FRTBZ |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | High Speed, Dual Channel, 6A, 4.5 to 16VOUT, Power MOSFET Drivers 驱动 光电二极管 接口集成电路 驱动器 |
文件: | 总14页 (文件大小:686K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NOT RECOMM
ENDED FOR NEW DE
SIGNS
NO RECOMMEND
ED REPLACEMENT
DATASHEET
contact our Tech
1-888-INTERSIL o
nical Support Cente
r at
r www.intersil.com/
tsc
ISL89160, ISL89161, ISL89162
High Speed, Dual Channel, 6A, 4.5 to 16V
FN7719
Rev 3.00
February 20, 2013
, Power MOSFET Drivers
OUT
The ISL89160, ISL89161, and ISL89162 are high-speed, 6A,
dual channel MOSFET drivers. These parts are identical to the
ISL89163, ISL89164, ISL89165 drivers but without the enable
inputs for each channel.
Features
• Dual output, 6A peak currents, can be paralleled
• Typical ON-resistance <1Ω
Two input logic thresholds are available: 3.3V (CMOS and TTL
compatible) and 5.0V (CMOS).
• Specified Miller plateau drive currents
• Very low thermal impedance ( = 3°C/W)
JC
Precision thresholds on all logic inputs allow the use of
external RC circuits to generate accurate and stable time
delays on both inputs, INA and INB. This capability is very
useful for dead time control.
• Hysteretic input logic levels for 3.3V CMOS, 5V CMOS, and
TTL
• Precision threshold inputs for time delays with external RC
components
At high switching frequencies, these MOSFET drivers use very
little bias current. Separate, non-overlapping drive circuits are
used to drive each CMOS output FET to prevent shoot-thru
currents in the output stage.
• 20ns rise and fall time driving a 10nF load.
• NC pins may be connected to ground or VDD to ease PCB
layout difficulties.
The start-up sequence is design to prevent unexpected glitches
Applications
when V is being turned on or turned off. When V < ~1V,
DD DD
• Synchronous Rectifier (SR) driver
• Switch mode power supplies
• Motor drives, class D amplifiers, UPS, inverters
• Pulse transformer driver
an internal 10kΩ resistor between the output and ground helps
to keep the output voltage low. When ~1V < V < UV, both
DD
outputs are driven low with very low resistance and the logic
inputs are ignored. This insures that the driven FETs are off.
When V > UVLO, and after a short delay, the outputs now
DD
respond to the logic inputs.
• Clock/line driver
Related Literature
• AN1603 “ISL6752/54EVAL1Z ZVS DC/DC Power Supply
with Synchronous Rectifiers User Guide”
3.5
3.0
POSITIVE THRESHOLD
VDD
2.5
2.0
NC
1
2
3
4
8
7
6
5
NC
INA
OUTA
1.5
EPAD
GND
INB
NEGATIVE THRESHOLD
OUTB
4.7µF
1.0
0.5
0.0
-40 -25 10
5
20
35
50
65
80
95 110 125
TEMPERATURE (°C)
FIGURE 1. TYPICAL APPLICATION
FIGURE 2. TEMPERATURE STABLE LOGIC THRESHOLDS
FN7719 Rev 3.00
February 20, 2013
Page 1 of 14
ISL89160, ISL89161, ISL89162
Block Diagram
VDD
Separate FET drives, with
non-overlapping outputs,
prevent shoot-thru
currents in the output
CMOS FETs resulting with
very low high frequency
operating currents.
For options A and B, the UV
comparator holds off the
For clarity, only one
channel is shown
outputs until VDD ~> 3.3VDC
.
ISL89160
INx
OUTx
10k
ISL89161,
ISL89162
EPAD
GND
For proper thermal and electrical
performance, the EPAD must be
connected to the PCB ground plane.
Pin Configurations
Pin Descriptions
PIN
NUMBER
ISL89160FR, ISL89160FB
(8 LD TDFN, EPSOIC)
TOP VIEW
ISL89161FR, ISL89161FB
(8 LD TDFN, EPSOIC)
TOP VIEW
SYMBOL
NC
DESCRIPTION
1, 8
No Connect. This pin may be left open or
connected to 0V or VDD
NC
INA
NC
8
7
6
5
1
2
3
4
NC
/INA
GND
/INB
NC
8
7
6
5
1
2
3
4
2
3
4
5
6
7
INA or /INA Channel A input, 0V to VDD
GND Power Ground, 0V
INB or /INB Channel B enable, 0V to VDD
OUTA
VDD
OUTB
OUTA
VDD
OUTB
GND
INB
OUTB
VDD
Channel B output
Power input, 4.5V to 16V
Channel A output, 0V to VDD
Power Ground, 0V
ISL89162FR, ISL89162FB
(8 LD TDFN, EPSOIC)
TOP VIEW
OUTA
EPAD
NC
/INA
GND
INB
NC
8
7
6
5
1
2
3
4
OUTA
VDD
OUTB
FN7719 Rev 3.00
February 20, 2013
Page 2 of 14
ISL89160, ISL89161, ISL89162
Ordering Information
PART NUMBER
TEMP RANGE
PACKAGE
(Pb-Free)
PKG.
DWG. #
(Notes 1, 2, 3)
ISL89160FRTAZ
ISL89161FRTAZ
ISL89162FRTAZ
ISL89160FBEAZ
ISL89161FBEAZ
ISL89162FBEAZ
ISL89160FRTBZ
ISL89161FRTBZ
ISL89162FRTBZ
ISL89160FBEBZ
ISL89161FBEBZ
ISL89162FBEBZ
NOTES:
PART MARKING
160A
(°C)
INPUT CONFIGURATION
non-inverting
INPUT LOGIC
3.3VDC
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
8 Ld 3x3 TDFN
8 Ld 3x3 TDFN
8 Ld 3x3 TDFN
8 Ld EPSOIC
8 Ld EPSOIC
8 Ld EPSOIC
8 Ld 3x3 TDFN
8 Ld 3x3 TDFN
8 Ld 3x3 TDFN
8 Ld EPSOIC
8 Ld EPSOIC
8 Ld EPSOIC
L8.3x3I
161A
inverting
L8.3x3I
L8.3x3I
M8.15D
M8.15D
M8.15D
L8.3x3I
L8.3x3I
L8.3x3I
M8.15D
M8.15D
M8.15D
162A
inverting + non-inverting
non-inverting
89160 FBEAZ
89161 FBEAZ
89162 FBEAZ
160B
inverting
inverting + non-inverting
non-inverting
5.0VDC
161B
inverting
162B
inverting + non-inverting
non-inverting
89160 FBEBZ
89161 FBEBZ
89162 FBEBZ
inverting
inverting + non-inverting
1. Add “-T*”, suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL89160, ISL89161, ISL89162. For more information on MSL, please
see Technical Brief TB363.
FN7719 Rev 3.00
February 20, 2013
Page 3 of 14
ISL89160, ISL89161, ISL89162
Absolute Maximum Ratings
Thermal Information
Supply Voltage, V Relative to GND. . . . . . . . . . . . . . . . . . . . . -0.3V to 18V
Logic Inputs (INA, INB). . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to V + 0.3V
DD
Thermal Resistance (Typical)
8 Ld TDFN Package (Notes 4, 5). . . . . . . . .
8 Ld EPSOIC Package (Notes 4, 5). . . . . . .
(°C/W)
44
42
(°C/W)
JC
DD
JA
3
3
Outputs (OUTA, OUTB) . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to V + 0.3V
DD
Average Output Current (Note 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150mA
ESD Ratings
Human Body Model Class 2 (Tested per JESD22-A114E) . . . . . . . 2000V
Machine Model Class B (Tested per JESD22-A115-A) . . . . . . . . . . . 200V
Charged Device Model Class IV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000V
Latch-Up (Tested per JESD-78B; Class 2, Level A) Output Current. . . 500mA
Max Power Dissipation at +25°C in Free Air . . . . . . . . . . . . . . . . . . . . . 2.27W
Max Power Dissipation at +25°C with Copper Plane . . . . . . . . . . . . .33.3W
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Operating Junction Temp Range . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Maximum Recommended Operating
Conditions
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Supply Voltage, V Relative to GND. . . . . . . . . . . . . . . . . . . . . .4.5V to 16V
DD
Logic Inputs (INA, INB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to V
Outputs (OUTA, OUTB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to V
DD
DD
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
JA
Brief TB379 for details.
5. For , the “case temp” location is the center of the exposed metal pad on the package underside.
JC
6. The average output current, when driving a power MOSFET or similar capacitive load, is the average of the rectified output current. The peak output
currents of this driver are self limiting by transconductance or r
and do not required any external components to minimize the peaks. If the
DS(ON)
output is driving a non-capacitive load, such as an LED, maximum output current must be limited by external means to less than the specified
absolute maximum.
DC Electrical Specifications
V
= 12V, GND = 0V, No load on OUTA or OUTB, unless otherwise specified. Boldface limits apply over
DD
the operating junction temperature range, -40°C to +125°C.
T = +25°C
J
T = -40°C to +125°C
J
MIN
MAX
PARAMETERS
POWER SUPPLY
Voltage Range
Quiescent Current
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
(Note 7)
(Note 7)
UNITS
V
-
-
-
-
-
-
4.5
16
V
DD
V
I
INx = GND
5
-
-
-
-
mA
mA
DD
DD
INA = INB = 1MHz, square wave
25
UnderVoltage
Undervoltage Lock-out
V
V
INA = INB = True (Note 10)
-
-
3.3
-
-
-
-
-
-
V
DD
UV
(Note 9, Figure 9)
Hysteresis
~25
mV
INPUTs (Note 11)
Input Range for INA, INB
V
-
-
-
-
-
-
-
-
-
-
-
-
-
GND
1.12
1.70
1.98
3.00
-
V
V
V
IN
DD
Logic 0 Threshold
for INA, INB (Note 9)
V
Option A, nominally 37% x 3.3V
Option B, nominally 37% x 5.0V
Option A, nominally 63% x 3.3V
Option B, nominally 63% x 5.0V
1.22
1.85
2.08
3.15
2
1.32
2.00
2.18
3.30
-
IL
IH
IN
V
Logic 1 Threshold
for INA, INB (Note 9)
V
C
V
V
Input Capacitance of
INA, INB (Note 8)
pF
FN7719 Rev 3.00
February 20, 2013
Page 4 of 14
ISL89160, ISL89161, ISL89162
DC Electrical Specifications
V
= 12V, GND = 0V, No load on OUTA or OUTB, unless otherwise specified. Boldface limits apply over
DD
the operating junction temperature range, -40°C to +125°C. (Continued)
T = +25°C
J
T = -40°C to +125°C
J
MIN
MAX
PARAMETERS
Input Bias Current
SYMBOL
TEST CONDITIONS
GND < V < V
MIN
-
TYP
-
MAX
-
(Note 7)
(Note 7)
UNITS
µA
I
-10
+10
IN
IN
DD
for INA, INB
OUTPUTS
High Level Output Voltage
Low Level Output Voltage
Peak Output Source Current
Peak Output Sink Current
NOTES:
V
V
-
-
-
-
-
-
-
-
-
-
V
- 0.1
V
DD
V
V
A
A
OHA OHB
DD
V
V
GND
GND + 0.1
OLA OLB
I
V
V
(initial) = 0V, C
= 10nF
-6
+6
-
-
-
-
O
O
O
LOAD
I
(initial) = 12V, C
= 10nF
O
LOAD
7. Compliance to data sheet limits is assured by one or more methods: production test, characterization and/or design.
8. This parameter is taken from the simulation models for the input FET. The actual capacitance on this input will be dominated by the PCB parasitic
capacitance.
9. A 400µs delay further inhibits the release of the output state when the UV positive going threshold is crossed. See Figure 9
10. The true state of a specific part number is defined by the input logic symbol.
11. The true state input voltage for the non-inverted inputs is greater than the Logic 1 threshold voltage. The true state input voltage for the inverted
inputs is less than the logic 0 threshold voltage.
AC Electrical Specifications
V
= 12V, GND = 0V, No Load on OUTA or OUTB, Unless Otherwise Specified. Boldface limits apply over
DD
the operating junction temperature range, -40°C to +125°C.
T = +25°C
J
T = -40°C to +125°C
J
PARAMETERS
SYMBOL
TEST CONDITIONS MIN
TYP
20
MAX
-
MIN
-
MAX
UNITS
ns
Output Rise Time (see Figure 4)
t
C
= 10nF,
-
-
-
-
-
-
40
R
LOAD
10% to 90%
Output Fall Time (see Figure 4)
t
C
= 10nF,
20
25
25
25
25
-
-
-
-
-
-
-
-
-
-
40
50
50
50
50
ns
ns
ns
ns
ns
F
LOAD
90% to 10%
Output Rising Edge Propagation Delay for
Non-Inverting Inputs (see Figure 3)
t
t
No load
RDLYn
Output Rising Edge Propagation Delay with Inverting
Inputs (see Figure 3)
t
No load
No load
No load
RDLYi
FDLYn
Output Falling Edge Propagation Delay with
Non-Inverting Inputs (see Figure 3)
Output Falling Edge Propagation Delay with Inverting
Inputs (see Figure 3)
t
FDLYi
Rising Propagation Matching (see Figure 3)
Falling Propagation Matching (see Figure 3)
t
No load
No load
-
-
-
<1
<1
6
-
-
-
-
-
-
-
-
-
ns
ns
A
RM
t
FM
Miller Plateau Sink Current
(See Test Circuit Figure 5)
-I
-I
-I
V
V
= 10V,
MP
MP
MP
DD
MILLER
= 5V
= 3V
= 2V
V
V
= 10V,
-
-
4.7
3.7
-
-
-
-
-
-
A
A
DD
MILLER
V
V
= 10V,
DD
MILLER
FN7719 Rev 3.00
February 20, 2013
Page 5 of 14
ISL89160, ISL89161, ISL89162
AC Electrical Specifications
V
= 12V, GND = 0V, No Load on OUTA or OUTB, Unless Otherwise Specified. Boldface limits apply over
DD
the operating junction temperature range, -40°C to +125°C. (Continued)
T = +25°C
J
T = -40°C to +125°C
J
PARAMETERS
Miller Plateau Source Current
SYMBOL
TEST CONDITIONS MIN
TYP
5.2
MAX
-
MIN
-
MAX
-
UNITS
A
I
I
I
V
V
= 10V,
-
-
-
MP
MP
MP
DD
MILLER
(See Test Circuit Figure 6)
= 5V
= 3V
= 2V
V
V
= 10V,
5.8
6.9
-
-
-
-
-
-
A
A
DD
MILLER
V
V
= 10V,
DD
MILLER
Test Waveforms and Circuits
3.3V*
50%
tRDLY
50%
tFDLY
INA,
INB
0V
90%
10%
/OUTA
OUTA
tRDLY
tFDLY
OUTA
OR
OUTB
/OUTB
OUTB
tR
tF
tRM
tFM
* Logic levels: A option = 3.3V, B option = 5.0V
FIGURE 4. RISE/FALL TIMES
FIGURE 3. PROP DELAYS AND MATCHING
ISL8916x
10V
10V
ISL8916x
0.1µF
10k
0.1µF
10k
VMILLER
VMILLER
10µF
10µF
200ns
200ns
10nF
+ISENSE
+ISENSE
10nF
0.1
0.1
-ISENSE
-ISENSE
FIGURE 5. MILLER PLATEAU SINK CURRENT TEST CIRCUIT
FIGURE 6. MILLER PLATEAU SOURCE CURRENT TEST CIRCUIT
FN7719 Rev 3.00
February 20, 2013
Page 6 of 14
ISL89160, ISL89161, ISL89162
Test Waveforms and Circuits (Continued)
CURRENT THROUGH
10V
0A
IMP
0.1 RESISTOR
VMILLER
VOUT
VOUT
VMILLER
CURRENT THROUGH
0.1 RESISTOR
-IMP
0V
0
200ns
200ns
FIGURE 7. MILLER PLATEAU SINK CURRENT
FIGURE 8. MILLER PLATEAU SOURCE CURRENT
RISING VDD
THIS DURATION IS DEPENDENT ON RISE
TIME OF VDD
3.3V UV THRESHOLD
THIS DURATION IS
INDEPENDENT ON RISE
TIME OF VDD
~1V
10k TO
GROUND
OUTPUTS CONTROLLED BY
LOGICAL INPUTS
OUTPUTS ACTIVE
LOW
OUTA, OUTB
OUTPUT STATE
UP TO 400µs
<1 TO GROUND
FIGURE 9. START-UP SEQUENCE
Typical Performance Curves
3.5
35
30
25
20
15
10
5
+125°C
+125°C
+25°C
-40°C
3.0
+25°C
-40°C
2.5
2.0
4
8
12
16
4
8
12
16
V
V
DD
DD
FIGURE 11. I vs V (1MHz)
DD DD
FIGURE 10. I vs V (STATIC)
DD DD
FN7719 Rev 3.00
February 20, 2013
Page 7 of 14
ISL89160, ISL89161, ISL89162
Typical Performance Curves(Continued)
50
1.1
1.0
16V
V
LOW
HIGH
OUT
40
30
20
10
0
NO LOAD
0.9
0.8
0.7
10V
5V
V
OUT
12V
0.6
0.5
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
FREQUENCY (MHz)
-45
-20
5
30
55
80
105
130
TEMPERATURE (°C)
FIGURE 12. I vs FREQUENCY (+25°C)
DD
FIGURE 13. r
vs TEMPERATURE
DS(ON)
25
20
15
30
25
FALL TIME, C
= 10nF
LOAD
OUTPUT FALLING PROP DELAY
OUTPUT RISING PROP DELAY
RISE TIME, C
= 10nF
LOAD
20
15
5
7
9
11
DD
13
15
-45
-20
5
30
55
80
105
130
V
TEMPERATURE (°C)
FIGURE 14. OUTPUT RISE/FALL TIME
FIGURE 15. PROPAGATION DELAY vs V
DD
ground, help to keep the gate voltage close to ground. When
Functional Description
~1V < V < UV, both outputs are driven low while ignoring the
DD
logic inputs. This low state has the same current sinking capacity
as during normal operation. This insures that the driven FETs are
held off even if there is a switching voltage on the drains that can
inject charge into the gates via the Miller capacitance. When
Overview
The ISL89160, ISL89161, ISL89162 drivers incorporate several
features including precision input logic thresholds, undervoltage
lock-out, and fast rising high output drive currents.
V
> UVLO, and after a 400µs delay, the outputs now respond
DD
to the logic inputs. See Figure 9 for complete details.
The precision input thresholds facilitate the use of an external RC
network to delay the rising or falling propagation of the driver
output. This is a useful feature to create dead times for bridge
applications to prevent shoot through.
For the negative transition of V through the UV lockout voltage,
DD
the outputs are active low when V < ~3.2V regardless of the
DD DC
input logic states.
The fast rising (or falling) output drive currents of the ISL89160,
ISL89161, ISL89162 minimize the turn-on (off) delays due to the
input capacitance of the driven FET. The switching transition period
at the Miller plateau is also minimized by high drive currents even
at these lower output voltages. (See the specified Miller plateau
currents in “AC Electrical Specifications” on page 5).
Application Information
Precision Thresholds for Time Delays
For input logic voltage option A, the nominal input negative
transition threshold is 1.22V and the positive transition threshold
is 2.08V (37% and 63% of 3.3V) Likewise, for input logic option B,
the nominal input negative transition threshold is 1.85V and the
positive transition threshold is 3.15V (37% and 63% of 4.0V).
The start-up sequence is designed to prevent unexpected glitches
when V is being turned on or turned off. When V < ~1V, an
DD DD
internal 10kΩ resistor connected between the output and
FN7719 Rev 3.00
February 20, 2013
Page 8 of 14
ISL89160, ISL89161, ISL89162
In Figure 16, R and C delay the rising edge of the input
Power Dissipation of the Driver
del
del
signal. For the falling edge of the input signal, the diode shorts
out the resistor resulting in a minimal falling edge delay. If the
diode polarity is reversed, the falling edge is delayed and the
rising delay is minimal.
The power dissipation of the ISL89160, ISL89161, ISL89162 is
dominated by the losses associated with the gate charge of the
driven bridge FETs and the switching frequency. The internal bias
current also contributes to the total dissipation but is usually not
significant as compared to the gate charge losses.
D
INx
12
OUTx
Rdel
cdel
10
V
= 64V
DS
8
6
4
2
0
V
= 40V
DS
FIGURE 16. DELAY USING RCD NETWORK
The 37% and 63% thresholds were chosen to simplify the
calculations for the desired time delays. When using an RC
circuit to generate a time delay, the delay is simply T (secs) = R
(ohms) x C (farads). Please note that this equation only applies if
the input logic voltage amplitude is 3.3V. If the logic high
amplitude is higher than 3.3V, the equations in Equation 1 can
be used for more precise delay calculations.
0
2
4
6
8
10 12 14 16 18 20 22 24
GATE CHARGE (nC)
High level of the logic signal into the RC
Positive going threshold
V
V
= 5V
H
Q
g,
= 63% 3.3V
THRESH
FIGURE 17. MOSFET GATE CHARGE vs GATE VOLTAGE
Low level of the logic signal into the RC
V
R
C
t
= 0.1V
L
Timing values
= 100
Figure 17 illustrates how the gate charge varies with the gate
voltage in a typical power MOSFET. In this example, the total gate
charge for V = 10V is 21.5nC when V = 40V. This is the
charge that a driver must source to turn-on the MOSFET and
must sink to turn-off the MOSFET.
del
del
= 1nF
= –R
V
– V
L
THRESH
gs DS
--------------------------------------------
C
LN
+ 1
del
del del
V
– V
H
L
t
= 51.731ns
Nominal delay time
(EQ. 1)
del
Equation 2 shows calculating the power dissipation of the driver:
In this example, the high input logic voltage is 5V, the positive
threshold is 63% of 3.3V and the low level input logic is 0.1V.
Note the rising edge propagation delay of the driver must be
added to this value.
R
gate
--------------------------------------------
P
= 2 Q freq V
+ I freq V
DD
D
c
GS
DD
R
+ r
DSON
gate
(EQ. 2)
where:
freq = Switching frequency,
= V bias of the ISL89160, ISL89161, ISL89162
The minimum recommended value of C is 100pF. The parasitic
capacitance of the PCB and any attached scope probes will
introduce significant delay errors if smaller values are used.
Larger values of C will further minimize errors.
V
GS
DD
Q = Gate charge for V
c
GS
(freq) = Bias current at the switching frequency (see
Acceptable values of R are primarily effected by the source
resistance of the logic inputs. Generally, 100Ω resistors or larger
are usable. A practical maximum value, limited by contamination
on the PCB, is 1MΩ
I
DD
Figure 10)
r
= ON-resistance of the driver
DS(ON)
Paralleling Outputs to Double the Peak Drive
Currents
R
= External gate resistance (if any).
gate
Note that the gate power dissipation is proportionally shared with
the external gate resistor and the output r . When sizing an
external gate resistor, do not overlook the power dissipated by
this resistor.
The typical propagation matching of the ISL89160 and ISL89161
is less than 1ns. The matching is so precise that carefully
matched and calibrated scopes probes and scope channels must
be used to make this measurement. Because of this excellent
performance, these driver outputs can be safely paralleled to
double the current drive capacity. It is important that the INA and
INB inputs be connected together on the PCB with the shortest
possible trace. This is also required of OUTA and OUTB. Note that
the ISL89162 cannot be paralleled because of the
DS(ON)
complementary logic.
FN7719 Rev 3.00
February 20, 2013
Page 9 of 14
ISL89160, ISL89161, ISL89162
Typical Application Circuit
VBRIDGE
ZVS FULL BRIDGE
SQR
PWM
LL
L
R
L
QUL
QUR
VGUL
VGUR
U1A
SQR
ISL89162
LR
T2
T1A
T1B
VLL
U1B
QLL
QLR
Red dashed lines
emphasize the
VLR
VGLL
VGLR
resonant switching
delay of the low-
side bridge FETs
VGLL
LL
LR
U2A
½ ISL89160
U2B
½ ISL89160
VGUL
VGLR
VGUR
LL: Lower Left
LR: Lower Right
UL: Upper Left
UR: Upper Right
GLL: Gate Lower Left
This is an example of how the ISL89160, ISL89161, ISL89162,
MOSFET drivers can be applied in a zero voltage switching full
bridge. Two main signals are required: a 50% duty cycle square
wave (SQR) and a PWM signal synchronized to the edges of the
SQR input. An ISL89162 is used to drive T1 with alternating half
• Be aware of magnetic fields emanating from transformers and
inductors. Gaps in these structures are especially bad for
emitting flux.
• If you must have traces close to magnetic devices, align the
traces so that they are parallel to the flux lines to minimize
coupling.
cycles driving Q and Q . An ISL89160 is used to drive Q and
UL UR LL
also with alternating half cycles. Unlike the two high-side
Q
LR
• The use of low inductance components such as chip resistors
and chip capacitors is highly recommended.
bridge FETs, the two low side bridge FETs are turned on with a
rising edge delay. The delay is setup by the RCD network on the
inputs to the ISL89160. The duration of the delay is chosen to
turn on the low-side FETs when the voltage on their respective
drains is at the resonant valley. For a complete description of the
ZVS topology, refer to AN1603 “ISL6752_54 Evaluation Board
Application Note”.
• Use decoupling capacitors to reduce the influence of parasitic
inductance in the VDD and GND leads. To be effective, these
caps must also have the shortest possible conduction paths. If
vias are used, connect several paralleled vias to reduce the
inductance of the vias.
• It may be necessary to add resistance to dampen resonating
parasitic circuits especially on OUTA and OUTB. If an external
gate resistor is unacceptable, then the layout must be
improved to minimize lead inductance.
General PCB Layout Guidelines
The AC performance of the ISL89160, ISL89161, ISL89162
depends significantly on the design of the PC board. The
following layout design guidelines are recommended to achieve
optimum performance:
• Keep high dv/dt nodes away from low level circuits. Guard
banding can be used to shunt away dv/dt injected currents
from sensitive circuits. This is especially true for control circuits
that source the input signals to the ISL89160, ISL89161,
ISL89162.
• Place the driver as close as possible to the driven power FET.
• Understand where the switching power currents flow. The high
amplitude di/dt currents of the driven power FET will induce
significant voltage transients on the associated traces.
• Avoid having a signal ground plane under a high amplitude
dv/dt circuit. This will inject di/dt currents into the signal
ground paths.
• Keep power loops as short as possible by paralleling the
source and return traces.
• Do power dissipation and voltage drop calculations of the
power traces. Many PCB/CAD programs have built in tools for
calculation of trace resistance.
• Use planes where practical; they are usually more effective
than parallel traces.
• Avoid paralleling high amplitude di/dt traces with low level
signal lines. High di/dt will induce currents and consequently,
noise voltages in the low level signal lines.
• Large power components (Power FETs, Electrolytic caps, power
resistors, etc.) will have internal parasitic inductance which
cannot be eliminated. This must be accounted for in the PCB
layout and circuit design.
• When practical, minimize impedances in low level signal
circuits. The noise, magnetically induced on a 10k resistor, is
10x larger than the noise on a 1k resistor.
• If you simulate your circuits, consider including parasitic
components especially parasitic inductance.
FN7719 Rev 3.00
February 20, 2013
Page 10 of 14
ISL89160, ISL89161, ISL89162
General EPAD Heatsinking
Considerations
EPAD GND
PLANE
EPAD GND
PLANE
The thermal pad is electrically connected to the GND supply
through the IC substrate. The epad of the ISL89160, ISL89161,
ISL89162 has two main functions: to provide a quiet GND for the
input threshold comparators and to provide heat sinking for the
IC. The EPAD must be connected to a ground plane and no
switching currents from the driven FET should pass through the
ground plane under the IC.
BOTTOM
LAYER
COMPONENT LAYER
Figure 18 is a PCB layout example of how to use vias to remove
heat from the IC through the epad.
FIGURE 18. TYPICAL PCB PATTERN FOR THERMAL VIAS
For maximum heatsinking, it is recommended that a ground
plane, connected to the EPAD, be added to both sides of the PCB.
A via array, within the area of the EPAD, will conduct heat from
the EPAD to the GND plane on the bottom layer. The number of
vias and the size of the GND planes required for adequate
heatsinking is determined by the power dissipated by the
ISL89160, ISL89161, ISL89162, the air flow and the maximum
temperature of the air around the IC.
© Copyright Intersil Americas LLC 2010-2013. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7719 Rev 3.00
February 20, 2013
Page 11 of 14
ISL89160, ISL89161, ISL89162
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest Rev.
DATE
REVISION
FN7719.3
CHANGE
December 20, 2012
Page 3 - Removed all ISL8916xFBECZ part numbers from Ordering Information table
Page 4 - ESD CDM value changed from 1500V to 1000V
January 31, 2012
FN7719.2
(page 1) Figure 1 illustration improved.
(page 1) Related literature added (AN1603).
(page 1) Last paragraph of the product description is changed to better describe the improved turn on
characteristics.
(page 1) Features list is revised to improve readability and to add new product specific features.
(page 3) Added parts for release in ordering information.
(page 4) Abs Max Ratings ESD Ratings Charged Device Model changed from “1000” to “1500”
(page 4) Note and figure references are added to the VDD Under-voltage lock-out parameter.
(page 5) Note 9 is revised to more clearly describe the turn-on characteristics.
(page 5) No load test conditions added to the rising and falling propagation matching parameters.
(page 7) Figure 9 added to clearly define the startup characteristics.
(page 8) The paragraphs of the Functional Description Overview describing the turn-on sequence is replaced by
3 paragraphs to more clearly describe the under voltage and turn-on and turn-off characteristics.
(page 9) A new section is added to the application information describing how the drivers outputs can be
paralleled.
(pages 1..12) Various minor corrections to text for grammar and spelling.
M8.15D POD on page 14 - Converted to new POD format. Removed table of dimensions and moved dimensions
onto drawing. Added land pattern.
January 13, 2011
January 12, 2011
Removed Option C Reference from Visio Graphics due to parts not releasing yet.
Converted to New Intersil Template
Updated page 1 Graphic by depicting 2 lines showing positive threshold and 2 lines showing negative threshold:
page 1 - Updated copyright to include 2011
FN7719.1
page 1 - Removed Related Literature from due to documentation being nonexistent at this time.
page 2 - Updated Pin Description Table by placing both pin numbers 1 and 8 on same line
page 3 - Updated Ordering Information by adding option B parts
page 4 - Added Note Reference to Inputs section in Electrical Spec Table
page 5 - Changed Note in Electrical Spec Table
From:
Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature
limits established by characterization and are not production tested.
To:
Compliance to data sheet limits is assured by one or more methods: production test, characterization and/or
design.
November 2, 2010
FN7719.0
Initial Release
About Intersil
Intersil Corporation is a leader in the design and manufacture of high-performance analog, mixed-signal and power management
semiconductors. The company's products address some of the fastest growing markets within the industrial and infrastructure,
personal computing and high-end consumer markets. For more information about Intersil or to find out how to become a member of
our winning team, visit our website and career page at www.intersil.com.
For a complete listing of Applications, Related Documentation and Related Parts, please see the respective product information page.
Also, please check the product information page to ensure that you have the most updated datasheet: ISL89160, ISL89161, ISL89162
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
Reliability reports are available from our website at: http://rel.intersil.com/reports/search.php
FN7719 Rev 3.00
February 20, 2013
Page 12 of 14
ISL89160, ISL89161, ISL89162
Package Outline Drawing
L8.3x3I
8 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE
Rev 1 6/09
2X 1.950
3.00
A
6X 0.65
B
5
8
(4X)
0.15
1.64 +0.10/ - 0.15
6
PIN 1
INDEX AREA
6
PIN #1 INDEX AREA
4
1
4
8X 0.30
0.10 M C A B
8X 0.400 ± 0.10
TOP VIEW
2.38
+0.10/ - 0.15
BOTTOM VIEW
SEE DETAIL "X"
( 2.38 )
( 1.95)
C
0.10
C
Max 0.80
0.08
C
SIDE VIEW
( 8X 0.60)
(1.64)
( 2.80 )
PIN 1
5
C
0 . 2 REF
(6x 0.65)
0 . 00 MIN.
0 . 05 MAX.
( 8 X 0.30)
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
Tiebar shown (if present) is a non-functional feature.
5.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
FN7719 Rev 3.00
February 20, 2013
Page 13 of 14
ISL89160, ISL89161, ISL89162
Package Outline Drawing
M8.15D
8 LEAD NARROW BODY SMALL OUTLINE EXPOSED PAD PLASTIC PACKAGE
Rev 1, 3/11
8
INDEX
AREA
6.20 (0.244)
5.84 (0.230)
DETAIL "A"
1.27 (0.050)
0.41 (0.016)
3.99 (0.157)
3.81 (0.150)
0.50 (0.02)
x 45°
1
2
3
0.25 (0.01)
TOP VIEW
8°
0°
0.25 (0.010)
0.19 (0.008)
SEATING PLANE
SIDE VIEW “B”
1.72 (0.067)
4.98 (0.196)
4.80 (0.189)
1.52 (0.059)
-C-
2.25
(0.089)
1.95
(0.077)
0.25 (0.010)
0.10 (0.004)
1.27 (0.050)
1
2
3
4
8
0.46 (0.019)
0.36 (0.014)
0.60 (0.023)
1.27 (0.050)
7
6
5
SIDE VIEW “A
1
2
3
5.45 (0.214)
2.50 (0.099)
2.00 (0.078)
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
8
1. Dimensions are in millimeters. Dimensions in ( ) for reference only.
2. Dimensioning and tolerancing per ASME-Y14.5M-1994.
3. Unless otherwise specified, tolerance: Decimal ± 0.05.
3.50 (0.137)
3.00 (0.118)
4. Dimension does not include interlead flash or protrusions. Interlead flash
or protrusions shall not exceed 0.25mm per side.
BOTTOM VIEW
5. The Pin 1 identifier may be either a mold or a mark feature.
6. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
FN7719 Rev 3.00
February 20, 2013
Page 14 of 14
相关型号:
ISL89160FRTBZ-T
High Speed, Dual Channel, 6A, 4.5 to 16VOUT, Power MOSFET Driver; DFN8, SOIC8; Temp Range: -40° to 125°C
RENESAS
ISL89161FBEAZ
High Speed, Dual Channel, 6A, 4.5 to 16VOUT, Power MOSFET Driver; DFN8, SOIC8; Temp Range: -40° to 125°C
RENESAS
ISL89161FBEAZ-T
High Speed, Dual Channel, 6A, 4.5 to 16VOUT, Power MOSFET Driver; DFN8, SOIC8; Temp Range: -40° to 125°C
RENESAS
ISL89161FBEBZ
High Speed, Dual Channel, 6A, 4.5 to 16VOUT, Power MOSFET Driver; DFN8, SOIC8; Temp Range: -40° to 125°C
RENESAS
ISL89161FBEBZ-T
High Speed, Dual Channel, 6A, 4.5 to 16VOUT, Power MOSFET Driver; DFN8, SOIC8; Temp Range: -40° to 125°C
RENESAS
©2020 ICPDF网 联系我们和版权申明