M37516MXH-XXXKP [RENESAS]
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER; 单片8位CMOS微机
| 型号： | M37516MXH-XXXKP |
| 厂家： | 
RENESAS TECHNOLOGY CORP |
| 描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 文件： | 总63页 (文件大小：1113K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
To all our customers
Regarding the change of names mentioned in the document, such as Mitsubishi
Electric and Mitsubishi XX, to Renesas Technology Corp.
The semiconductor operations of Hitachi and Mitsubishi Electric were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Mitsubishi Electric, Mitsubishi Electric Corporation, Mitsubishi
Semiconductors, and other Mitsubishi brand names are mentioned in the document, these names
have in fact all been changed to Renesas Technology Corp. Thank you for your understanding.
Except for our corporate trademark, logo and corporate statement, no changes whatsoever have been
made to the contents of the document, and these changes do not constitute any alteration to the
contents of the document itself.
Note : Mitsubishi Electric will continue the business operations of high frequency & optical devices
and power devices.
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
ꢀClock generating circuit..................................... Built-in 2 circuits
(connect to external ceramic resonator or quartz-crystal oscillator)
ꢀPower source voltage
DESCRIPTION
The 7516 group (Spec. H) is the 8-bit microcomputer based on the
740 family core technology.
In high-speed mode .................................................. 4.0 to 5.5 V
(at 8 MHz oscillation frequency)
The 7516 group (Spec. H) is designed for the household products
and office automation equipment and includes serial I/O functions,
2
In high-speed mode .................................................. 2.7 to 5.5 V
(at 4 MHz oscillation frequency)
8-bit timer, A-D converter, and I C-BUS interface.
In middle-speed mode............................................... 2.7 to 5.5 V
(at 8 MHz oscillation frequency)
FEATURES
ꢀBasic machine-language instructions ...................................... 71
ꢀMinimum instruction execution time .................................. 0.5 µs
(at 8 MHz oscillation frequency)
In low-speed mode .................................................... 2.7 to 5.5 V
(at 32 kHz oscillation frequency)
ꢀPower dissipation
ꢀMemory size
In high-speed mode ..........................................................34 mW
(at 8 MHz oscillation frequency, at 5 V power source voltage)
In low-speed mode ............................................................ 60 µW
(at 32 kHz oscillation frequency, at 3 V power source voltage)
ꢀOperating temperature range....................................–20 to 85°C
ROM ............................................................... 16 K to 24 K bytes
RAM ................................................................... 512 to 640 bytes
ꢀProgrammable input/output ports ............................................ 36
ꢀInterrupts ................................................. 17 sources, 16 vectors
ꢀTimers ............................................................................. 8-bit ꢀ 4
ꢀSerial I/O1 ................... 8-bit ꢀ 1 (UART or Clock-synchronized)
ꢀSerial I/O2 ................................... 8-bit ꢀ 1(Clock-synchronized)
APPLICATION
Office automation equipment, FA equipment, Household products,
2
ꢀMulti-master I C-BUS interface (option) ...................... 1 channel
Consumer electronics, etc.
ꢀPWM ............................................................................... 8-bit ꢀ 1
ꢀA-D converter ............................................... 10-bit ꢀ 6 channels
ꢀWatchdog timer ............................................................ 16-bit ꢀ 1
PIN CONFIGURATION (TOP VIEW)
34
22
21
20
19
18
17
16
15
14
13
12
P1
P1
3
/(LED
3
4
)
)
P3
P3
P3
P3
P3
P3
5
/AN
/AN
/AN
/AN
/AN
/AN
5
35
36
37
38
39
40
41
42
43
44
4/(LED
4
3
4
3
P1
P1
5/(LED
5
6
)
)
6/(LED
2
1
0
2
1
0
P1
7/(LED
7
)
M37516MXH-XXXKP
V
SS
OUT
IN
VCC
X
VREF
X
AVSS
RESET
P2
P2
P45
0
/XCOUT
/XCIN
P44/INT3/PWM
1
Package type : 44PJX-A
Fig. 1 M37516MXH-XXXKP pin configuration
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FUNCTIONAL BLOCK
Fig.2 Functional block diagram
2
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 1 Pin description
Functions
Pin
Name
Function except a port function
Power source
CNVSS input
•Apply voltage of 2.7 V – 5.5 V to Vcc, and 0 V to Vss.
•This pin controls the operation mode of the chip.
•Normally connected to VSS.
VCC, VSS
CNVSS
Reference
voltage input
VREF
AVss
•Reference voltage input pin for A-D converter.
Analog power
source input
•Analog power source input pin for A-D converter.
•Connect to Vss.
Reset input
Clock input
RESET
XIN
•Reset input pin for active “L”.
•Input and output pins for the clock generating circuit.
•Connect a ceramic resonator or quartz-crystal oscillator between the XIN and XOUT pins to set
the oscillation frequency.
Clock output
I/O port P0
XOUT
•When an external clock is used, connect the clock source to the XIN pin and leave the XOUT
pin open.
• Serial I/O2 function pin
P00/SIN2
•8-bit CMOS I/O port.
P01/SOUT2
P02/SCLK2
P03/SRDY2
•I/O direction register allows each pin to be individually
programmed as either input or output.
•CMOS compatible input level.
•CMOS 3-state output structure.
P04–P07
P10–P17
I/O port P1
I/O port P2
•P10 to P17 (8 bits) are enabled to output large current for LED drive.
•8-bit CMOS I/O port.
• Sub-clock generating circuit I/O
pins (connect a resonator)
P20/XCOUT
P21/XCIN
•I/O direction register allows each pin to be individually
programmed as either input or output.
2
• I C-BUS interface function pins
P22/SDA1
P23/SCL1
•CMOS compatible input level.
2
P24/SDA2/RxD
P25/SCL2/TxD
• I C-BUS interface function pin/
•P22 to P25 can be switched between CMOS compat-
ible input level or SMBUS input level in the I C-BUS
2
Serial I/O1 function pins
interface function.
P26/SCLK
• Serial I/O1 function pin
•P20, P21, P24 to P27: CMOS 3-state output structure.
P27/CNTR0/
SRDY1
• Serial I/O1 function pin/
Timer X function pin
2
•P24, P25: N-channel open-drain structure in the I C-
BUS interface function.
•P22, P23: N-channel open-drain structure.
P30/AN0–
P35/AN5
I/O port P3
I/O port P4
•8-bit CMOS I/O port with the same function as port P0. • A-D converter input pin
•CMOS compatible input level.
•CMOS 3-state output structure.
P40/CNTR1
• Timer Y function pin
• Interrupt input pins
•8-bit CMOS I/O port with the same function as port P0.
•CMOS compatible input level.
P41/INT0
P42/INT1
•CMOS 3-state output structure.
P43/INT2/SCMP2
P44/INT3/PWM
P45
• Interrupt input pin/SCMP2 output pin
• Interrupt input pin/PWM output pin
3
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PART NUMBERING
Product name
M37516
M
6
H– XXX KP
Package type
KP : 44PJX-A
ROM number
Omitted in One Time PROM version shipped in blank and
flash memory version.
– : standard
Omitted in One Time PROM version shipped in blank and
flash memory version.
H– : Partial specification changed version
ROM/PROM size
: 4096 bytes
: 8192 bytes
: 12288 bytes
: 16384 bytes
: 20480 bytes
: 24576 bytes
: 28672 bytes
: 32768 bytes
9: 36864 bytes
A: 40960 bytes
B: 45056 bytes
C: 49152 bytes
D: 53248 bytes
E: 57344 bytes
F: 61440 bytes
1
2
3
4
5
6
7
8
The first 128 bytes and the last 2 bytes of ROM are reserved areas ; they
cannot be used as a user’s ROM area.
Memory type
M : Mask ROM version
E : One Time PROM version
Differences of functions
Fig. 3 Part numbering
4
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GROUP EXPANSION
Mitsubishi plans to expand the 7516 group (Spec. H) as follows.
Memory Type
Support for mask ROM and One Time PROM versions.
Memory Size
Mask ROM size ................................................. 16 K to 24 K bytes
One Time PROM size..................................................... 24 K bytes
RAM size .............................................................. 512 to 640 bytes
Packages
44PJX-A............................................... 44-pin plastic-molded QFN
Memory Expansion Plan
ROM size (bytes)
As of Oct. 2002
ROM
exteranal
32K
28K
Mass production
M37516M6H/E6H
24K
20K
16K
12K
8K
Mass production
M37516M4H
384
512
640
768
896
1024
1152
1280
1408
1536
2048
RAM size (bytes)
Fig. 4 Memory expansion plan
5
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Currently planning products are listed below.
Table 2 Support products
As of Oct. 2002
Remarks
ROM size (bytes)
Product name
RAM size (bytes)
Package
44PJX-A
ROM size for User in (
)
16384
(16254)
M37516M4H-XXXKP
512
640
Mask ROM version
M37516M6H-XXXKP
M37516E6HKP
24576
(24446)
One Time PROM version (blank)
6
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FUNCTIONAL DESCRIPTION
[Stack Pointer (S)]
CENTRAL PROCESSING UNIT (CPU)
The 7516 group (Spec. H) uses the standard 740 Family instruc-
tion set. Refer to the table of 740 Family addressing modes and
machine instructions or the 740 Family Software Manual for de-
tails on the instruction set.
The stack pointer is an 8-bit register used during subroutine calls
and interrupts. This register indicates start address of stored area
(stack) for storing registers during subroutine calls and interrupts.
The low-order 8 bits of the stack address are determined by the
contents of the stack pointer. The high-order 8 bits of the stack ad-
dress are determined by the stack page selection bit. If the stack
page selection bit is “0” , the high-order 8 bits becomes “0016”. If
the stack page selection bit is “1”, the high-order 8 bits becomes
“0116”.
Machine-resident 740 Family instructions are as follows:
The FST and SLW instructions cannot be used.
The STP, WIT, MUL, and DIV instructions can be used.
[Accumulator (A)]
The operations of pushing register contents onto the stack and
popping them from the stack are shown in Figure 6.
Store registers other than those described in Figure 6 with pro-
gram when the user needs them during interrupts or subroutine
calls.
The accumulator is an 8-bit register. Data operations such as data
transfer, etc., are executed mainly through the accumulator.
[Index Register X (X)]
The index register X is an 8-bit register. In the index addressing
modes, the value of the OPERAND is added to the contents of
register X and specifies the real address.
[Program Counter (PC)]
The program counter is a 16-bit counter consisting of two 8-bit
registers PCH and PCL. It is used to indicate the address of the
next instruction to be executed.
[Index Register Y (Y)]
The index register Y is an 8-bit register. In partial instruction, the
value of the OPERAND is added to the contents of register Y and
specifies the real address.
b0
b7
A
Accumulator
b0
b7
X
Index register X
b7
b0
Y
Index register Y
b7
b0
S
Stack pointer
b15
b7
b7
b0
PCH
PCL
Program counter
b0
N V T B D I Z C
Processor status register (PS)
Carry flag
Zero flag
Interrupt disable flag
Decimal mode flag
Break flag
Index X mode flag
Overflow flag
Negative flag
Fig. 5 740 Family CPU register structure
7
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
On-going Routine
Execute JSR
Interrupt request
(Note)
M (S) (PCH)
(S) (S) – 1
Push return address
on stack
M (S) (PCH)
(S) (S) – 1
M (S) (PCL)
(S) (S)– 1
Subroutine
M (S) (PCL)
(S) (S) – 1
Push return address
on stack
Push contents of processor
status register on stack
M (S) (PS)
(S) (S) – 1
Interrupt
Service Routine
I Flag is set from “0” to “1”
Execute RTS
(S) (S) + 1
Fetch the jump vector
Execute RTI
(S) (S) + 1
POP return
address from stack
POP contents of
processor status
register from stack
(PCL) M (S)
(S) (S) + 1
(PCH) M (S)
(PS)
M (S)
(S) (S) + 1
(PCL) M (S)
(S) (S) + 1
(PCH) M (S)
POP return
address
from stack
Note: Condition for acceptance of an interrupt
Interrupt enable flag is “1”
Interrupt disable flag is “0”
Fig. 6 Register push and pop at interrupt generation and subroutine call
Table 3 Push and pop instructions of accumulator or processor status register
Push instruction to stack
Pop instruction from stack
Accumulator
PHA
PHP
PLA
PLP
Processor status register
8
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
•Bit 4: Break flag (B)
[Processor status register (PS)]
The B flag is used to indicate that the current interrupt was
generated by the BRK instruction. The BRK flag in the processor
status register is always “0”. When the BRK instruction is used to
generate an interrupt, the processor status register is pushed
onto the stack with the break flag set to “1”.
The processor status register is an 8-bit register consisting of 5
flags which indicate the status of the processor after an arithmetic
operation and 3 flags which decide MCU operation. Branch opera-
tions can be performed by testing the Carry (C) flag , Zero (Z) flag,
Overflow (V) flag, or the Negative (N) flag. In decimal mode, the Z,
V, N flags are not valid.
•Bit 5: Index X mode flag (T)
When the T flag is “0”, arithmetic operations are performed
between accumulator and memory. When the T flag is “1”, direct
arithmetic operations and direct data transfers are enabled
between memory locations.
•Bit 0: Carry flag (C)
The C flag contains a carry or borrow generated by the arithmetic
logic unit (ALU) immediately after an arithmetic operation. It can
also be changed by a shift or rotate instruction.
•Bit 1: Zero flag (Z)
•Bit 6: Overflow flag (V)
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location
operated on by the BIT instruction is stored in the overflow flag.
•Bit 7: Negative flag (N)
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is “0”, and cleared if the result is anything other
than “0”.
•Bit 2: Interrupt disable flag (I)
The I flag disables all interrupts except for the interrupt
generated by the BRK instruction.
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7 of
the memory location operated on by the BIT instruction is stored
in the negative flag.
Interrupts are disabled when the I flag is “1”.
•Bit 3: Decimal mode flag (D)
The D flag determines whether additions and subtractions are
executed in binary or decimal. Binary arithmetic is executed when
this flag is “0”; decimal arithmetic is executed when it is “1”.
Decimal correction is automatic in decimal mode. Only the ADC
and SBC instructions can be used for decimal arithmetic.
Table 4 Set and clear instructions of each bit of processor status register
C flag
Z flag
I flag
D flag
B flag
T flag
V flag
_
N flag
_
_
_
_
_
_
Set instruction
SEC
CLC
SEI
CLI
SED
CLD
SET
CLT
Clear instruction
CLV
9
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[CPU Mode Register (CPUM)] 003B16
The CPU mode register contains the stack page selection bit, etc.
The CPU mode register is allocated at address 003B16.
b7
b0
CPU mode register
CPUM : address 003B16)
1
(
Processor mode bits
b1 b0
0
0
1
1
0 : Single-chip mode
1 :
0 :
1 :
Not available
Stack page selection bit
0 : 0 page
1 : 1 page
Fix this bit to “1”.
Port XC switch bit
0 : I/O port function (stop oscillating)
1 : XCIN–XCOUT oscillating function
Main clock (XIN–XOUT) stop bit
0 : Oscillating
1 : Stopped
Main clock division ratio selection bits
b7 b6
0
0
1
1
0 : φ = f(XIN)/2 (high-speed mode)
1 : φ = f(XIN)/8 (middle-speed mode)
0 : φ = f(XCIN)/2 (low-speed mode)
1 : Not available
Fig. 7 Structure of CPU mode register
10
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MEMORY
Interrupt Vector Area
Special Function Register (SFR) Area
The Special Function Register area in the zero page contains con-
trol registers such as I/O ports and timers.
The interrupt vector area contains reset and interrupt vectors.
Zero Page
Access to this area with only 2 bytes is possible in the zero page
RAM
addressing mode.
RAM is used for data storage and for stack area of subroutine
calls and interrupts.
Special Page
Access to this area with only 2 bytes is possible in the special
ROM
page addressing mode.
The first 128 bytes and the last 2 bytes of ROM are reserved for
device testing and the rest is user area for storing programs.
Product name
M37516M4H
M37516M6H/E6H
RAM size
512 bytes
640 bytes
ROM size
16 Kbytes
24 Kbytes
000016
SFR area
Zero page
004016
RAM
010016
RAM area
RAM size
(bytes)
Address
XXXX16
023F16
02BF16
XXXX16
512
640
Reserved area
044016
ROM area
ROM size
(bytes)
16384
Address
YYYY16
C00016
A00016
Address
ZZZZ16
C08016
A08016
Not used
24576
YYYY16
Reserved ROM area
(128 bytes)
ZZZZ16
FF0016
ROM
Special page
FFDC16
Interrupt vector area
FFFE16
Reserved ROM area
FFFF16
Fig. 8 Memory map diagram
11
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Port P0 (P0)
Prescaler 12 (PRE12)
Timer 1 (T1)
000016
000116
000216
000316
000416
000516
000616
000716
000816
000916
000A16
000B16
000C16
000D16
000E16
000F16
001016
001116
001216
001316
001416
001516
001616
001716
002016
002116
002216
002316
002416
002516
002616
002716
002816
002916
002A16
Port P0 direction register (P0D)
Port P1 (P1)
Timer 2 (T2)
Port P1 direction register (P1D)
Port P2 (P2)
Timer XY mode register (TM)
Prescaler X (PREX)
Timer X (TX)
Port P2 direction register (P2D)
Port P3 (P3)
Prescaler Y (PREY)
Timer Y (TY)
Port P3 direction register (P3D)
Port P4 (P4)
Timer count source selection register (TCSS)
Port P4 direction register (P4D)
2
002B16 I C data shift register (S0)
2
I C address register (S0D)
002C16
002D16
002E16
002F16
003016
003116
003216
003316
003416
003516
003616
003716
003816
003916
003A16
003B16
003C16
003D16
003E16
003F16
2
I C status register (S1)
2
I C control register (S1D)
2
I C clock control register (S2)
2
I C start/stop condition control register (S2D)
Reserved ✽
Reserved ✽
Reserved ✽
A-D control register (ADCON)
Reserved ✽
A-D conversion low-order register (ADL)
A-D conversion high-order register (ADH)
Serial I/O2 control register 1 (SIO2CON1)
Serial I/O2 control register 2 (SIO2CON2)
Serial I/O2 register (SIO2)
MISRG
001816 Transmit/Receive buffer register (TB/RB)
Serial I/O1 status register (SIOSTS)
Serial I/O1 control register (SIOCON)
UART control register (UARTCON)
Baud rate generator (BRG)
Watchdog timer control register (WDTCON)
Interrupt edge selection register (INTEDGE)
001916
001A16
001B16
001C16
001D16
001E16
CPU mode register (CPUM)
Interrupt request register 1 (IREQ1)
Interrupt request register 2 (IREQ2)
Interrupt control register 1 (ICON1)
Interrupt control register 2 (ICON2)
PWM control register (PWMCON)
PWM prescaler (PREPWM)
001F16 PWM register (PWM)
✽ Reserved : Do not write any data to the reserved area.
Fig. 9 Memory map of special function register (SFR)
12
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
I/O PORTS
The I/O ports have direction registers which determine the input/
output direction of each individual pin. Each bit in a direction reg-
ister corresponds to one pin, and each pin can be set to be input
port or output port.
When “0” is written to the bit corresponding to a pin, that pin be-
comes an input pin. When “1” is written to that bit, that pin
becomes an output pin.
If data is read from a pin which is set to output, the value of the
port output latch is read, not the value of the pin itself. Pins set to
input are floating. If a pin set to input is written to, only the port
output latch is written to and the pin remains floating.
Table 5 I/O port function
Input/Output
Related SFRs
Ref.No.
Name
I/O Structure
Non-Port Function
Pin
P00/SIN2
P01/SOUT2
P02/SCLK2
P03/SRDY2
CMOS compatible
input level
CMOS 3-state output
Input/output,
individual
bits
Serial I/O2 function I/O
Serial I/O2 control
register
Port P0
(1)
(2)
(3)
(4)
(5)
P04–P07
P10–P17
Port P1
Port P2
P20/XCOUT
P21/XCIN
Sub-clock generating CPU mode register
circuit
(6)
(7)
2
P22/SDA1
P23/SCL1
2
(8)
(9)
CMOS compatible
input level
I C control register
I C-BUS interface func-
tion I/O
CMOS/SMBUS input
level (when selecting
2
I C-BUS interface
function)
N-channel open-drain
output
2
P24/SDA2/RxD
P25/SCL2/TxD
CMOS compatible
input level
(10)
(11)
I C control register
2
I C-BUS interface func-
Serial I/O1 control
register
tion I/O
CMOS/SMBUS input
level (when selecting
Serial I/O1 function I/O
2
I C-BUS interface
function)
CMOS 3-state output
N-channel open-drain
output (when
2
selecting I C-BUS
interface function)
P26/SCLK
CMOS compatible
input level
Serial I/O1 function I/O
Serial I/O1 control
register
(12)
(13)
CMOS 3-state output
Serial I/O1 control
register
P27/CNTR0/
SRDY1
Serial I/O1 function I/O
Timer X function I/O
Timer XY mode register
A-D control register
P30/AN0–
P35/AN5
Port P3
Port P4
A-D conversion input
(14)
P40/CNTR1
Timer Y function I/O
Timer XY mode register
(15)
(16)
P41/INT0
P42/INT1
External interrupt input
Interrupt edge selection
register
P43/INT2/SCMP2
Interrupt edge selection
register
External interrupt input
SCMP2 output
(17)
Serial I/O2 control
register
P44/INT3/PWM
P45
External interrupt input
PWM output
Interrupt edge selection
register
(18)
(5)
PWM control register
13
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(1) Port P0
0
(2) Port P0
1
P01/SOUT2 P-channel output
disable bit
Direction
register
Serial I/O2 transmit completion signal
Serial I/O2 port selection bit
Direction
register
Data bus
Port latch
Data bus
Port latch
Serial I/O2 input
Serial I/O2 output
(3) Port P0
2
(4) Port P0
3
P02/SCLK2 P-channel output disable bit
Serial I/O2 synchronous clock
SRDY2 output enable bit
selection bit
Serial I/O2 port selection bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
Serial I/O2 ready output
Serial I/O2 clock output
Serial I/O2 external clock input
(5) Ports P0
4–P07, P1, P4
5
(6) Port P20
Port XC switch bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
Oscillator
Port P2
1
Port XC switch bit
(7) Port P2
1
(8) Port P22
I C-BUS interface enable bit
SDA/SCL pin selection bit
2
Port XC switch bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
Sub-clock generating circuit input
SDA output
SDA input
Fig. 10 Port block diagram (1)
14
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(9) Port P2
I C-BUS interface enable bit
SDA/SCL pin selection bit
3
(10) Port P2
I C-BUS interface enable bit
SDA/SCL pin selection bit
4
2
2
Serial I/O1 enable bit
Receive enable bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
SDA input
SDA output
SCL output
Serial I/O1 input
SCL input
(11) Port P2
5
(12) Port P26
P-channel output disable bit
Serial I/O1 synchronous clock
Serial I/O1 enable bit
Transmit enable bit
I C-BUS interface enable bit
SDA/SCL pin selection bit
selection bit
Serial I/O1 enable bit
2
Serial I/O1 mode selection bit
Direction
register
Serial I/O1 enable bit
Direction
register
Data bus
Port latch
Data bus
Port latch
SCL input
Serial I/O1 output
SCL output
Serial I/O1 clock output
External clock input
(13) Port P2
7
(14) Ports P3
0
–P3
5
Pulse output mode
Serial I/O1 mode selection bit
Serial I/O1 enable bit
S
RDY1 output enable bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
Pulse output mode
A-D converter input
CNTR
interrupt input
0
Serial ready output
Analog input pin
selection bit
Timer output
(16) Ports P4
1
, P42
(15) Port P4
0
Direction
register
Direction
register
Data bus
Data bus
Port latch
Port latch
Pulse output mode
Timer output
Interrupt input
CNTR1 interrupt input
Fig. 11 Port block diagram (2)
15
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(17) Port P4
3
(18) Port P44
PWM output enable bit
Serial I/O2 input/output
comparison signal control bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
PWM output
Serial I/O2 input/output
comparison signal output
Interrupt input
Interrupt input
Fig. 12 Port block diagram (3)
16
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
INTERRUPTS
Interrupts occur by 17 sources among 17 sources: seven external,
✽Notes
When setting the followings, the interrupt request bit may be set to
nine internal, and one software.
“1”.
•When setting external interrupt active edge
Interrupt Control
Related register: Interrupt edge selection register (address 3A16)
2
Each interrupt is controlled by an interrupt request bit, an interrupt
enable bit, and the interrupt disable flag except for the software in-
terrupt set by the BRK instruction. An interrupt occurs if the
corresponding interrupt request and enable bits are “1” and the in-
terrupt disable flag is “0”.
I C start/stop condition control register (address 3016
)
Timer XY mode register (address 2316)
•When switching interrupt sources of an interrupt vector address
where two or more interrupt sources are allocated
Related register: Interrupt edge selection register (address 3A16)
When not requiring for the interrupt occurrence synchronized with
these setting, take the following sequence.
Interrupt enable bits can be set or cleared by software.
Interrupt request bits can be cleared by software, but cannot be
set by software.
✽Set the corresponding interrupt enable bit to “0” (disabled).
✽Set the interrupt edge select bit or the interrupt source select bit.
✽Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
The BRK instruction cannot be disabled with any flag or bit. The I
(interrupt disable) flag disables all interrupts except the BRK in-
struction interrupt.
When several interrupts occur at the same time, the interrupts are
received according to priority.
✽Set the corresponding interrupt enable bit to “1” (enabled).
Interrupt Operation
By acceptance of an interrupt, the following operations are auto-
matically performed:
1. The contents of the program counter and the processor status
register are automatically pushed onto the stack.
2. The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
3. The interrupt jump destination address is read from the vector
table into the program counter.
17
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 6 Interrupt vector addresses and priority
Vector Addresses (Note 1)
Interrupt Request
Generating Conditions
Remarks
Non-maskable
Interrupt Source
Reset (Note 2)
INT0
Priority
High
Low
1
2
FFFD16
FFFC16
At reset
At detection of either rising or
falling edge of INT0 input
External interrupt
(active edge selectable)
FFFB16
FFF916
FFFA16
FFF816
At detection of either rising or
falling edge of SCL or SDA input
External interrupt
(active edge selectable)
3
SCL, SDA
INT1
At detection of either rising or External interrupt
falling edge of INT1 input
FFF616
FFF416
4
5
FFF716
FFF516
(active edge selectable)
External interrupt
(active edge selectable)
At detection of either rising or
falling edge of INT2 input
INT2
INT3
At detection of either rising or External interrupt
falling edge of INT3 input
(active edge selectable)
6
FFF316
FFF216
At completion of serial I/O2 data Switch by Serial I/O2/INT3
reception/transmission
Serial I/O2
interrupt source bit
2
FFF116
FFEF16
FFED16
FFF016
FFEE16
FFEC16
FFEA16
FFE816
7
8
9
I C
At completion of data transfer
At timer X underflow
Timer X
Timer Y
Timer 1
Timer 2
At timer Y underflow
At timer 1 underflow
10
11
FFEB16
FFE916
STP release timer underflow
Valid when serial I/O1 is selected
Valid when serial I/O1 is selected
At timer 2 underflow
At completion of serial I/O1 data
reception
Serial I/O1
reception
12
13
FFE716
FFE516
FFE616
FFE416
At completion of serial I/O1
transfer shift or when transmis-
sion buffer is empty
Serial I/O1
transmission
External interrupt
(active edge selectable)
At detection of either rising or
falling edge of CNTR0 input
CNTR0
CNTR1
14
15
FFE216
FFE016
FFE316
FFE116
At detection of either rising or
falling edge of CNTR1 input
External interrupt
(active edge selectable)
A-D converter
16
17
FFDF16
FFDD16
FFDE16
FFDC16
At completion of A-D conversion
At BRK instruction execution
BRK instruction
Non-maskable software interrupt
Notes 1: Vector addresses contain interrupt jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
18
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Interrupt request bit
Interrupt enable bit
Interrupt disable flag (I)
BRK instruction
Reset
Interrupt request
Fig. 13 Interrupt control
b7
b0
Interrupt edge selection register
(INTEDGE : address 003A16
)
INT
INT
INT
INT
0
active edge selection bit
1
2
3
active edge selection bit
active edge selection bit
active edge selection bit
0 : Falling edge active
1 : Rising edge active
Serial I/O2 / INT3 interrupt source bit
0 : INT interrupt selected
3
1 : Serial I/O2 interrupt selected
Not used (returns “0” when read)
b7
b0
b7
b0
Interrupt request register 2
(IREQ2 : address 003D16
Interrupt request register 1
)
(IREQ1 : address 003C16
)
Timer 1 interrupt request bit
Timer 2 interrupt request bit
Serial I/O1 reception interrupt request bit
Serial I/O1 transmit interrupt request bit
INT
0 interrupt request bit
SCL/SDA interrupt request bit
INT
INT
INT
1
2
3
interrupt request bit
interrupt request bit
/ Serial I/O2 interrupt request bit
CNTR
0
interrupt request bit
interrupt request bit
CNTR
1
I2C interrupt request bit
Timer X interrupt request bit
Timer Y interrupt request bit
AD converter interrupt request bit
Not used (returns “0” when read)
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
b7
b0
b7
b0
Interrupt control register 2
Interrupt control register 1
(ICON2 : address 003F16
)
(ICON1 : address 003E16
)
INT interrupt enable bit
0
Timer 1 interrupt enable bit
SCL/SDA interrupt enable bit
Timer 2 interrupt enable bit
INT
INT
INT
1
2
3
interrupt enable bit
interrupt enable bit
/ Serial I/O2 interrupt enable bit
Serial I/O1 reception interrupt enable bit
Serial I/O1 transmit interrupt enable bit
CNTR
CNTR
0
interrupt enable bit
interrupt enable bit
I2C interrupt enable bit
1
Timer X interrupt enable bit
Timer Y interrupt enable bit
AD converter interrupt enable bit
Not used (returns “0” when read)
(Do not write “1” to this bit.)
0 : Interrupts disabled
1 : Interrupts enabled
0 : Interrupts disabled
1 : Interrupts enabled
Fig. 14 Structure of interrupt-related registers
19
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
TIMERS
Timer X and Timer Y
Timer X and Timer Y can each select in one of four operating
The 7516 group (Spec. H) has four timers: timer X, timer Y, timer
1, and timer 2.
modes by setting the timer XY mode register.
The division ratio of each timer or prescaler is given by 1/(n + 1),
where n is the value in the corresponding timer or prescaler latch.
All timers are count down. When the timer reaches “0016”, an un-
derflow occurs at the next count pulse and the corresponding
timer latch is reloaded into the timer and the count is continued.
When a timer underflows, the interrupt request bit corresponding
to that timer is set to “1”.
(1) Timer Mode
The timer counts the count source selected by Timer count source
selection bit.
(2) Pulse Output Mode
The timer counts the count source selected by Timer count source
selection bit. Whenever the contents of the timer reach “0016”, the
signal output from the CNTR0 (or CNTR1) pin is inverted. If the
CNTR0 (or CNTR1) active edge selection bit is “0”, output begins
at “ H”.
b0
b7
Timer XY mode register
(TM : address 002316
)
Timer X operating mode bits
b1b0
If it is “1”, output starts at “L”. When using a timer in this mode, set
the corresponding port P27 ( or port P40) direction register to out-
put mode.
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
CNTR0 active edge selection bit
(3) Event Counter Mode
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
Operation in event counter mode is the same as in timer mode,
except that the timer counts signals input through the CNTR0 or
CNTR1 pin.
When the CNTR0 (or CNTR1) active edge selection bit is “0”, the
rising edge of the CNTR0 (or CNTR1) pin is counted.
When the CNTR0 (or CNTR1) active edge selection bit is “1”, the
falling edge of the CNTR0 (or CNTR1) pin is counted.
Timer X count stop bit
0: Count start
1: Count stop
Timer Y operating mode bits
b5b4
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
(4) Pulse Width Measurement Mode
If the CNTR0 (or CNTR1) active edge selection bit is “0”, the timer
counts the selected signals by the count source selection bit while
the CNTR0 (or CNTR1) pin is at “H”. If the CNTR0 (or CNTR1) ac-
tive edge selection bit is “1”, the timer counts it while the CNTR0
(or CNTR1) pin is at “L”.
CNTR1 active edge selection bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
Timer Y count stop bit
0: Count start
1: Count stop
The count can be stopped by setting “1” to the timer X (or timer Y)
count stop bit in any mode. The corresponding interrupt request
bit is set each time a timer underflows.
Fig. 15 Structure of timer XY mode register
✽Note
b0
b7
Timer count source selection register
(TCSS : address 002816
When switching the count source by the timer 12, X and Y count
source bits, the value of timer count is altered in unconsiderable
amount owing to generating of a thin pulses in the count input
signals.
)
Timer X count source selection bit
0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode)
1 : f(XIN)/2 (f(XCIN)/2 at low-speed mode)
Timer Y count source selection bit
0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode)
1 : f(XIN)/2 (f(XCIN)/2 at low-speed mode)
Therefore, select the timer count source before set the value to
the prescaler and the timer.
Timer 12 count source selection bit
0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode)
1 : f(XCIN
)
When timer X/timer Y underflow while executing the instruction
which sets “1” to the timer X/timer Y count stop bits, the timer X/
timer Y interrupt request bits are set to “1”. Timer X/Timer Y in-
terrupts are received if these interrupts are enabled at this time.
The timing which interrupt is accepted has a case after the in-
struction which sets “1” to the count stop bit, and a case after
the next instruction according to the timing of the timer under-
flow. When this interrupt is unnecessary, set “0” (disabled) to the
interrupt enable bit and then set “1” to the count stop bit.
Not used (returns “0” when read)
Fig. 16 Structure of timer count source selection register
Timer 1 and Timer 2
The count source of prescaler 12 is the oscillation frequency
which is selected by timer 12 count source selection bit. The out-
put of prescaler 12 is counted by timer 1 and timer 2, and a timer
underflow sets the interrupt request bit.
20
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Data bus
f(XIN)/16
(f(XCIN)/16 at low-speed mode)
Prescaler X latch (8)
Timer X latch (8)
f(XIN)/2
Pulse width
measurement
mode
(f(XCIN)/2 at low-speed mode)
Timer mode
Pulse output mode
Timer X count source selection bit
To timer X interrupt
request bit
Prescaler X (8)
Timer X count stop bit
Timer X (8)
CNTR0 active edge
selection bit
Event
counter
mode
P27/CNTR0/SRDY1
“0”
To CNTR
0 interrupt
request bit
“1”
CNTR0 active
“1”
“0”
edge selection
bit
Q
Q
T
Toggle flip-flop
R
Timer X latch write pulse
Pulse output mode
Port P2
latch
7
Port P2
direction register
7
Pulse output mode
Data bus
f(XIN)/16
Prescaler Y latch (8)
Timer Y latch (8)
Timer Y (8)
(f(XCIN)/16 at low-speed mode)
f(XIN)/2
Pulse width
measure-
(f(XCIN)/2 at low-speed mode)
Timer mode
ment mode Pulse output mode
Timer Y count source selection bit
To timer Y interrupt
request bit
Prescaler Y (8)
CNTR1 active edge
selection bit
Event
counter
mode
Timer Y count stop bit
P40/CNTR1
“0”
To CNTR
1 interrupt
request bit
“1”
CNTR1 active
“1”
“0”
edge selection
bit
Q
Q
T
Toggle flip-flop
R
Port P4
latch
0
Timer Y latch write pulse
Pulse output mode
Port P4
0
direction register
Pulse output mode
Data bus
Prescaler 12 latch (8)
Prescaler 12 (8)
Timer 1 latch (8)
Timer 1 (8)
Timer 2 latch (8)
Timer 2 (8)
f(XIN)/16
(f(XCIN)/16 at low-speed mode)
To timer 2 interrupt
request bit
f(XCIN
)
Timer 12 count source selection bit
To timer 1 interrupt
request bit
Fig. 17 Block diagram of timer X, timer Y, timer 1, and timer 2
21
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
SERIAL I/O
(1) Clock Synchronous Serial I/O Mode
Clock synchronous serial I/O mode can be selected by setting the
serial I/O1 mode selection bit of the serial I/O1 control register (bit
6 of address 001A16) to “1”.
✽SERIAL I/O1
Serial I/O1 can be used as either clock synchronous or asynchro-
nous (UART) serial I/O. A dedicated timer is also provided for
baud rate generation.
For clock synchronous serial I/O, the transmitter and the receiver
must use the same clock. If an internal clock is used, transfer is
started by a write signal to the TB/RB.
Data bus
Serial I/O1 control register
Address 001A16
Address 001816
Receive buffer register
Receive buffer full flag (RBF)
Receive shift register
Receive interrupt request (RI)
P24/RXD
Shift clock
Clock control circuit
P26/SCLK
Serial I/O1 synchronous
clock selection bit
Frequency division ratio 1/(n+1)
BRG count source selection bit
1/4
X
IN
Baud rate generator
Address 001C16
1/4
Clock control circuit
Falling-edge detector
P27/SRDY1
F/F
Shift clock
Transmit shift register
Transmit buffer register
Transmit shift completion flag (TSC)
Transmit interrupt source selection bit
P25/TXD
Transmit interrupt request (TI)
Transmit buffer empty flag (TBE)
Serial I/O1 status register
Address 001916
Address 001816
Data bus
Fig. 18 Block diagram of clock synchronous serial I/O1
Transfer shift clock
(1/2 to 1/2048 of the internal
clock, or an external clock)
Serial output TxD
Serial input RxD
D
0
0
D
1
1
D
2
2
D
3
3
D
4
4
D
5
5
D
6
6
D
7
7
D
D
D
D
D
D
D
D
Receive enable signal SRDY1
Write pulse to receive/transmit
buffer register (address 001816
)
RBF = 1
TSC = 1
Overrun error (OE)
detection
TBE = 0
TBE = 1
TSC = 0
Notes 1: As the transmit interrupt (TI), either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has
ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O1 control register.
2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data
is output continuously from the TxD pin.
3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” .
Fig. 19 Operation of clock synchronous serial I/O1 function
22
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O1 mode selection bit (b6) of the serial I/O1
control register to “0”.
two buffers have the same address in memory. Since the shift reg-
ister cannot be written to or read from directly, transmit data is
written to the transmit buffer register, and receive data is read
from the receive buffer register.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
The transmit and receive shift registers each have a buffer, but the
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
Data bus
Address 001816
Serial I/O1 control register Address 001A16
OE
Character length selection bit
Receive buffer full flag (RBF)
Receive interrupt request (RI)
Receive buffer register
P24/RXD
ST detector
7 bits
8 bits
Receive shift register
1/16
UART control register
SP detector
PE FE
Address 001B16
Clock control circuit
Serial I/O1 synchronous clock selection bit
P26/SCLK
Frequency division ratio 1/(n+1)
BRG count source selection bit
1/4
X
IN
Baud rate generator
Address 001C16
ST/SP/PA generator
1/16
Transmit shift completion flag (TSC)
Transmit interrupt source selection bit
P25/T
X
D
Transmit shift register
Transmit interrupt request (TI)
Character length selection bit
Transmit buffer empty flag (TBE)
Transmit buffer register
Address 001816
Address 001916
Serial I/O1 status register
Data bus
Fig. 20 Block diagram of UART serial I/O1
23
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Transmit or receive clock
Transmit buffer write
signal
TBE=0
TSC=0
TBE=1
TBE=0
TBE=1
TSC=1
Serial output TXD
ST
SP
D0
D1
ST
D0
D1
SP
1 start bit
Generated at 2nd bit in 2-stop-bit mode
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
Receive buffer read
signal
RBF=0
RBF=1
SP
RBF=1
SP
ST
Serial input R
X
D
D0
D1
ST
D0
D1
Notes
1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O1 control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Fig. 21 Operation of UART serial I/O1 function
[Serial I/O1 Control Register (SIOCON)] 001A16
The serial I/O1 control register consists of eight control bits for the
serial I/O1 function.
[Transmit Buffer Register/Receive Buffer
Register (TB/RB)] 001816
The transmit buffer register and the receive buffer register are lo-
cated at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[UART Control Register (UARTCON)] 001B16
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer and one bit (bit 4) which is al-
ways valid and sets the output structure of the P25/TXD pin.
[Serial I/O1 Status Register (SIOSTS)] 001916
The read-only serial I/O1 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O1
function and various errors.
[Baud Rate Generator (BRG)] 001C16
The baud rate generator determines the baud rate for serial trans-
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
fer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate genera-
tor.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer reg-
ister, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O1 enable bit SIOE
(bit 7 of the serial I/O1 control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O1 status register are initialized to “0” at
reset, but if the transmit enable bit (bit 4) of the serial I/O1 control
register has been set to “1”, the transmit shift completion flag (bit
2) and the transmit buffer empty flag (bit 0) become “1”.
24
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
b0
b7
Serial I/O1 status register
(SIOSTS : address 001916
Serial I/O1 control register
)
(SIOCON : address 001A16
BRG count source selection bit (CSS)
0: f(XIN
)
Transmit buffer empty flag (TBE)
0: Buffer full
1: Buffer empty
)
1: f(XIN)/4
Serial I/O1 synchronous clock selection bit (SCS)
0: BRG output divided by 4 when clock synchronous
serial I/O1 is selected, BRG output divided by 16
when UART is selected.
Receive buffer full flag (RBF)
0: Buffer empty
1: Buffer full
1: External clock input when clock synchronous serial
I/O1 is selected, external clock input divided by 16
when UART is selected.
Transmit shift completion flag (TSC)
0: Transmit shift in progress
1: Transmit shift completed
S
0: P2
1: P2
RDY1 output enable bit (SRDY)
Overrun error flag (OE)
0: No error
1: Overrun error
7
pin operates as ordinary I/O pin
pin operates as SRDY1 output pin
7
Transmit interrupt source selection bit (TIC)
0: Interrupt when transmit buffer has emptied
1: Interrupt when transmit shift operation is completed
Parity error flag (PE)
0: No error
1: Parity error
Transmit enable bit (TE)
0: Transmit disabled
1: Transmit enabled
Framing error flag (FE)
0: No error
1: Framing error
Receive enable bit (RE)
0: Receive disabled
1: Receive enabled
Summing error flag (SE)
0: (OE) U (PE) U (FE)=0
1: (OE) U (PE) U (FE)=1
Serial I/O1 mode selection bit (SIOM)
0: Clock asynchronous (UART) serial I/O
1: Clock synchronous serial I/O
Not used (returns “1” when read)
Serial I/O1 enable bit (SIOE)
0: Serial I/O1 disabled
b7
b0
UART control register
(UARTCON : address 001B16
(pins P2
1: Serial I/O1 enabled
(pins P2 to P2 operate as serial I/O1 pins)
4 to P27 operate as ordinary I/O pins)
)
4
7
Character length selection bit (CHAS)
0: 8 bits
1: 7 bits
Parity enable bit (PARE)
0: Parity checking disabled
1: Parity checking enabled
Parity selection bit (PARS)
0: Even parity
1: Odd parity
Stop bit length selection bit (STPS)
0: 1 stop bit
1: 2 stop bits
P25/TXD P-channel output disable bit (POFF)
0: CMOS output (in output mode)
1: N-channel open drain output (in output mode)
Not used (return “1” when read)
Fig. 22 Structure of serial I/O1 control registers
✽Notes on serial I/O1
2
1. When using the serial I/O1, clear the I C-BUS interface enable
bit to “0” or the SDA/SCL interrupt pin selection bit to “0”.
2. When setting the transmit enable bit of serial I/O1 to “1”, the
serial I/O1 transmit interrupt request bit is automatically set to
“1”. When not requiring the interrupt occurrence synchronized
with the transmission enalbed, take the following sequence.
✽Set the serial I/O1 transmit interrupt enable bit to “0” (dis-
abled).
✽Set the transmit enable bit to “1”.
✽Set the serial I/O1 transmit interrupt request bit to “0” after 1
or more instructions have been executed.
✽Set the serial I/O1 transmit interrupt enable bit to “1” (en-
abled).
25
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
✽SERIAL I/O2
The serial I/O2 can be operated only as the clock synchronous type.
b7
b0
Serial I/O2 control register 1
As a synchronous clock for serial transfer, either internal clock or
external clock can be selected by the serial I/O2 synchronous clock
selection bit (b6) of serial I/O2 control register 1.
(SIO2CON1 : address 001516
)
Internal synchronous clock selection bits
b2 b1 b0
0
0
0
0
1
1
0
0
1
1
1
1
0: f(XIN)/8 (f(XCIN)/8 in low-speed mode)
1: f(XIN)/16 (f(XCIN)/16 in low-speed mode)
0: f(XIN)/32 (f(XCIN)/32 in low-speed mode)
1: f(XIN)/64 (f(XCIN)/64 in low-speed mode)
0: f(XIN)/128 f(XCIN)/128 in low-speed mode)
1: f(XIN)/256 (f(XCIN)/256 in low-speed mode)
The internal clock incorporates a dedicated divider and permits se-
lecting 6 types of clock by the internal synchronous clock selection
bits (b2, b1, b0) of serial I/O2 control register 1.
Regarding SOUT2 and SCLK2 being output pins, either CMOS output
format or N-channel open-drain output format can be selected by the
P01/SOUT2, P02/SCLK2 P-channel output disable bit (b7) of
serial I/O2 control register 1.
Serial I/O2 port selection bit
0: I/O port
1: SOUT2,SCLK2 output pin
When the internal clock has been selected, a transfer starts by a
write signal to the serial I/O2 register (address 001716). After comple-
tion of data transfer, the level of the SOUT2 pin goes to high imped-
ance automatically but bit 7 of the serial I/O2 control register 2 is not
set to “1” automatically.
S
0: P0
1: P0
RDY2 output enable bit
3
pin is normal I/O pin
3
pin is SRDY2 output pin
Transfer direction selection bit
0: LSB first
When the external clock has been selected, the contents of the serial
I/O2 register is continuously sifted while transfer clocks are input.
Accordingly, control the clock externally. Note that the SOUT2 pin does
not go to high impedance after completion of data transfer.
To cause the SOUT2 pin to go to high impedance in the case where
the external clock is selected, set bit 7 of the serial I/O2 control reg-
ister 2 to “1” when SCLK2 is “H” after completion of data transfer. After
the next data transfer is started (the transfer clock falls), bit 7 of the
serial I/O2 control register 2 is set to “0” and the SOUT2 pin is put into
the active state.
1: MSB first
Serial I/O2 synchronous clock selection bit
0: External clock
1: Internal clock
P01/SOUT2 ,P02/SCLK2 P-channel output disable bit
0: CMOS output (in output mode)
1: N-channel open-drain output (in output mode )
b7
b0
Serial I/O2 control register 2
(SIO2CON2 : address 001616
)
Optional transfer bits
b2 b1 b0
Regardless of the internal clock to external clock, the interrupt re-
quest bit is set after the number of bits (1 to 8 bits) selected by the
optional transfer bit is transferred. In case of a fractional number of
bits less than 8 bits as the last data, the received data to be stored in
the serial I/O2 register becomes a fractional number of bits close to
MSB if the transfer direction selection bit of serial I/O2 control regis-
ter 1 is LSB first, or a fractional number of bits close to LSB if the
transfer direction selection bit is MSB first. For the remaining bits, the
previously received data is shifted.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0: 1 bit
1: 2 bit
0: 3 bit
1: 4 bit
0: 5 bit
1: 6 bit
0: 7 bit
1: 8 bit
Not used ( returns "0" when read)
Serial I/O2 I/O comparison signal control bit
At transmit operation using the clock synchronous serial I/O, the SCMP2
signal can be output by comparing the state of the transmit pin SOUT2
with the state of the receive pin SIN2 in synchronization with a rise of
the transfer clock. If the output level of the SOUT2 pin is equal to the
input level to the SIN2 pin, “L” is output from the SCMP2 pin. If not, “H”
is output. At this time, an INT2 interrupt request can also be gener-
ated. Select a valid edge by bit 2 of the interrupt edge selection reg-
ister (address 003A16).
0: P4
1: SCMP2 output
3 I/O
S
OUT2 pin control bit (P0
0: Output active
1: Output high-impedance
1)
Fig. 23 Structure of Serial I/O2 control registers 1, 2
[Serial I/O2 Control Registers 1, 2 (SIO2CON1 /
SIO2CON2)] 001516, 001616
The serial I/O2 control registers 1 and 2 are containing various se-
lection bits for serial I/O2 control as shown in Figure 23.
26
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Internal synchronous
clock selection bits
1/8
X
CIN
1/16
1/32
Data bus
“10”
Main clock division ratio
selection bits (Note)
1/64
“00”
“01”
1/128
1/256
X
IN
P0
3
latch
Serial I/O2 synchronous
clock selection bit
“0”
“1”
P03/SRDY2
SRDY2
Synchronous circuit
“1”
S
RDY2 output enable bit
“0”
External clock
P02 latch
“0”
Optional transfer bits (3)
Serial I/O counter 2 (3)
P02
/SCLK2
Serial I/O2
“1”
interrupt request
Serial I/O2 port selection bit
P01 latch
“0”
P0
1
/SOUT2
/SIN2
“1”
Serial I/O2 port selection bit
Serial I/O2 register (8)
P00
P43 latch
“0”
D
P43
/SCMP2/INT2
Q
“1”
Serial I/O2 I/O comparison
signal control bit
Note: Either high-speed, middle-speed or low-speed mode is selected by bits 6 and 7 of CPU mode register.
Fig. 24 Block diagram of Serial I/O2
Transfer clock (Note 1)
Write-in signal to
serial I/O2 register
(Note 2)
.
Serial I/O2 output
SOUT2
D0
D1
D2
D3
D4
D5
D6
D7
Serial I/O2 input SIN2
Receive enable signal SRDY2
Serial I/O2 interrupt request bit set
Notes
1: When the internal clock is selected as a transfer clock, the f(XIN) clock division (f(XCIN) in low-speed mode) can be selected
by setting bits 0 to 2 of serial I/O2 control register 1.
2: When the internal clock is selected as a transfer clock, the SOUT2 pin has high impedance after transfer completion.
Fig. 25 Timing chart of Serial I/O2
27
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
S
S
CMP2
CLK2
SOUT2
S
IN2
Judgement of I/O data comparison
Fig. 26 SCMP2 output operation
28
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
2
2
Table 7 Multi-master I C-BUS interface functions
MULTI-MASTER I C-BUS INTERFACE
2
The multi-master I C-BUS interface is a serial communications cir-
Item
Function
2
cuit, conforming to the Philips I C-BUS data transfer format. This
2
In conformity with Philips I C-BUS
standard:
interface, offering both arbitration lost detection and a synchro-
nous functions, is useful for the multi-master serial
communications.
10-bit addressing format
7-bit addressing format
High-speed clock mode
Standard clock mode
Format
2
Figure 27 shows a block diagram of the multi-master I C-BUS in-
2
terface and Table 7 lists the multi-master I C-BUS interface
2
In conformity with Philips I C-BUS
functions.
standard:
2
2
Master transmission
Master reception
Slave transmission
Slave reception
This multi-master I C-BUS interface consists of the I C address
Communication mode
SCL clock frequency
2
2
register, the I C data shift register, the I C clock control register,
2
2
2
the I C control register, the I C status register, the I C start/stop
condition control register and other control circuits.
16.1 kHz to 400 kHz (at φ = 4 MHz)
2
When using the multi-master I C-BUS interface, set 1 MHz or
System clock φ = f(XIN)/2 (high-speed mode)
φ = f(XIN)/8 (middle-speed mode)
more to φ.
Note: Mitsubishi Electric Corporation assumes no responsibility for in-
fringement of any third-party’s rights or originating in the use of the
connection control function between the I2C-BUS interface and the
ports SCL1, SCL2, SDA1 and SDA2 with the bit 6 of I2C control regis-
ter (002E16).
b7
I2C address register
b0
Interrupt
generating
circuit
Interrupt request signal
(IICIRQ)
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RWB
S0D
Address comparator
I2C data shift register
Noise
elimination
circuit
Data
control
circuit
Serial data
(SDA
b7
b0
)
b7
b0
S0
AL AAS AD0 LRB
MST TRX BB PIN
S1
AL
circuit
SIS SIP
SSC4 SSC3 SSC2 SSC1 SSC0
I2C status register
2
I C start/stop condition
S2D
control register
Internal data bus
BB
circuit
I2C clock control register
Noise
elimination
circuit
S1D
Serial
clock
Clock
control
circuit
b7
ACK
S2
b0
b7
b0
10BIT
SAD
ACK FAST
CCR4 CCR3 CCR2 CCR1 CCR0
TSEL
TISS
(SCL
)
ALS ES0 BC2 BC1 BC0
MODE
BIT
S1D I2C control register
System clock (φ)
I2C clock control register
Clock division
Bit counter
2
Fig. 27 Block diagram of multi-master I C-BUS interface
✽✽: Purchase of MITSUBISHI ELECTRIC CORPORATIONS I2C components conveys a license under the Philips I2C Patent Rights to use these components
an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
29
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
2
[I C Data Shift Register (S0)] 002B16
2
The I C data shift register (S0 : address 002B16) is an 8-bit shift
b7
b0
I2C address register
(S0D: address 002C16
register to store receive data and write transmit data.
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RWB
)
When transmit data is written into this register, it is transferred to
the outside from bit 7 in synchronization with the SCL clock, and
each time one-bit data is output, the data of this register are
shifted by one bit to the left. When data is received, it is input to
this register from bit 0 in synchronization with the SCL clock, and
each time one-bit data is input, the data of this register are shifted
by one bit to the left. The minimum 2 machine cycles are required
from the rising of the SCL clock until input to this register.
Read/write bit
Slave address
2
Fig. 28 Structure of I C address register
2
The I C data shift register is in a write enable status only when the
2
I C-BUS interface enable bit (ES0 bit : bit 3 of address 002E16) of
2
the I C control register is “1”. The bit counter is reset by a write in-
2
struction to the I C data shift register. When both the ES0 bit and
2
the MST bit of the I C status register (address 002D16) are “1,” the
2
SCL is output by a write instruction to the I C data shift register.
2
Reading data from the I C data shift register is always enabled re-
gardless of the ES0 bit value.
2
[I C Address Register (S0D)] 002C16
2
The I C address register (address 002C16) consists of a 7-bit
slave address and a read/write bit. In the addressing mode, the
slave address written in this register is compared with the address
data to be received immediately after the START condition is de-
tected.
•Bit 0: Read/write bit (RWB)
This is not used in the 7-bit addressing mode. In the 10-bit ad-
dressing mode, the first address data to be received is compared
2
with the contents (SAD6 to SAD0 + RWB) of the I C address reg-
ister.
The RWB bit is cleared to “0” automatically when the stop condi-
tion is detected.
•Bits 1 to 7: Slave address (SAD0–SAD6)
These bits store slave addresses. Regardless of the 7-bit address-
ing mode and the 10-bit addressing mode, the address data
transmitted from the master is compared with the contents of
these bits.
30
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
2
[I C Clock Control Register (S2)] 002F16
b7
b0
2
The I C clock control register (address 002F16) is used to set ACK
I2C clock control register
(S2 : address 002F16
ACK FAST
BIT MODE
ACK
CCR4 CCR3 CCR2 CCR1 CCR0
control, SCL mode and SCL frequency.
)
•Bits 0 to 4: SCL frequency control bits (CCR0–CCR4)
These bits control the SCL frequency. Refer to Table 8.
•Bit 5: SCL mode specification bit (FAST MODE)
This bit specifies the SCL mode. When this bit is set to “0,” the
standard clock mode is selected. When the bit is set to “1,” the
high-speed clock mode is selected.
S
CL frequency control bits
Refer to Table 8.
S
CL mode specification bit
0 : Standard clock mode
1 : High-speed clock
2
When connecting the bus of the high-speed mode I C bus stan-
ACK bit
0 : ACK is returned.
1 : ACK is not
dard (maximum 400 kbits/s), use 8 MHz or more oscillation
frequency f(XIN) and 2 division clock.
•Bit 6: ACK bit (ACK BIT)
ACK clock bit
✽
This bit sets the SDA status when an ACK clock is generated.
0 : No ACK clock
1 : ACK clock
When this bit is set to “0,” the ACK return mode is selected and
SDA goes to “L” at the occurrence of an ACK clock. When the bit
is set to “1,” the ACK non-return mode is selected. The SDA is
held in the “H” status at the occurrence of an ACK clock.
2
Fig. 29 Structure of I C clock control register
2
Table 8 Set values of I C clock control register and SCL
However, when the slave address agree with the address data in
the reception of address data at ACK BIT = “0,” the SDA is auto-
matically made “L” (ACK is returned). If there is a disagreement
between the slave address and the address data, the SDA is auto-
matically made “H” (ACK is not returned).
frequency
Setting value of
CCR4–CCR0
SCL frequency (Note 1)
(at φ = 4 MHz, unit : kHz)
Standard clock
mode
High-speed clock
mode
CCR4 CCR3 CCR2 CCR1 CCR0
Setting disabled Setting disabled
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
✽ACK clock: Clock for acknowledgment
Setting disabled
Setting disabled
333
Setting disabled
Setting disabled
– (Note 2)
– (Note 2)
100
•Bit 7: ACK clock bit (ACK)
This bit specifies the mode of acknowledgment which is an ac-
knowledgment response of data transfer. When this bit is set to
“0,” the no ACK clock mode is selected. In this case, no ACK clock
occurs after data transmission. When the bit is set to “1,” the ACK
clock mode is selected and the master generates an ACK clock
each completion of each 1-byte data transfer. The device for
transmitting address data and control data releases the SDA at
the occurrence of an ACK clock (makes SDA “H”) and receives the
ACK bit generated by the data receiving device.
250
400 (Note 3)
166
83.3
500/CCR value 1000/CCR value
(Note 3)
(Note 3)
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
34.5
17.2
33.3
16.6
32.3
16.1
Note: Do not write data into the I2C clock control register during transfer. If
data is written during transfer, the I2C clock generator is reset, so
that data cannot be transferred normally.
Notes 1: Duty of SCL clock output is 50 %. The duty becomes 35 to 45 %
only when the high-speed clock mode is selected and CCR value
= 5 (400 kHz, at φ = 4 MHz). “H” duration of the clock fluctuates
from –4 to +2 machine cycles in the standard clock mode, and
fluctuates from –2 to +2 machine cycles in the high-speed clock
mode. In the case of negative fluctuation, the frequency does not
increase because “L” duration is extended instead of “H” duration
reduction.
These are value when SCL clock synchronization by the synchro-
nous function is not performed. CCR value is the decimal
notation value of the SCL frequency control bits CCR4 to CCR0.
2: Each value of SCL frequency exceeds the limit at φ = 4 MHz or
more. When using these setting value, use φ of 4 MHz or less.
3: The data formula of SCL frequency is described below:
φ/(8 ✽ CCR value) Standard clock mode
φ/(4 ✽ CCR value) High-speed clock mode (CCR value ≠ 5)
φ/(2 ✽ CCR value) High-speed clock mode (CCR value = 5)
Do not set 0 to 2 as CCR value regardless of φ frequency.
Set 100 kHz (max.) in the standard clock mode and 400 kHz
(max.) in the high-speed clock mode to the SCL frequency by set-
ting the SCL frequency control bits CCR4 to CCR0.
31
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
2
[I C Control Register (S1D)] 002E16
2
The I C control register (address 002E16) controls data communi-
TSEL
SCL
1
2
/P23
cation format.
SCL
•Bits 0 to 2: Bit counter (BC0–BC2)
These bits decide the number of bits for the next 1-byte data to be
SCL
/TxD/P2
5
TSEL
TSEL
Multi-master
2
2
transmitted. The I C interrupt request signal occurs immediately
I C-BUS interface
after the number of count specified with these bits (ACK clock is
added to the number of count when ACK clock is selected by ACK
clock bit (bit 7 of address 002F16)) have been transferred, and
BC0 to BC2 are returned to “0002”.
SDA
SDA
1
/P22
SDA
2
/RxD/P2
4
TSEL
Also when a START condition is received, these bits become
“0002” and the address data is always transmitted and received in
8 bits.
Fig. 30 SDA/SCL pin selection bit
2
•Bit 3: I C interface enable bit (ES0)
2
This bit enables to use the multi-master I C-BUS interface. When
this bit is set to “0,” the use disable status is provided, so that the
SDA and the SCL become high-impedance. When the bit is set to
“1,” use of the interface is enabled.
b7
b0
I2C control register
(S1D : address 002E16
TSEL 10 BIT
SAD
ES0
TISS
ALS
BC2 BC1 BC0
)
When ES0 = “0,” the following is performed.
Bit counter (Number of
transmit/receive bits)
b2 b1 b0
2
• PIN = “1,” BB = “0” and AL = “0” are set (which are bits of the I C
status register at address 002D16 ).
2
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
: 8
: 7
: 6
: 5
: 4
: 3
: 2
: 1
• Writing data to the I C data shift register (address 002B16) is dis-
abled.
•Bit 4: Data format selection bit (ALS)
This bit decides whether or not to recognize slave addresses.
When this bit is set to “0,” the addressing format is selected, so
that address data is recognized. When a match is found between a
slave address and address data as a result of comparison or when
I2C-BUS interface
enable bit
0 : Disabled
2
a general call (refer to “I C Status Register,” bit 1) is received,
transfer processing can be performed. When this bit is set to “1,”
the free data format is selected, so that slave addresses are not
recognized.
1 : Enabled
Data format selection bit
0 : Addressing format
1 : Free data format
•Bit 5: Addressing format selection bit (10BIT SAD)
This bit selects a slave address specification format. When this bit
is set to “0,” the 7-bit addressing format is selected. In this case,
Addressing format
selection bit
0 : 7-bit addressing
2
only the high-order 7 bits (slave address) of the I C address regis-
format
ter (address 002C16) are compared with address data. When this
1 : 10-bit addressing
format
bit is set to “1,” the 10-bit addressing format is selected, and all
2
the bits of the I C address register are compared with address
SDA/SCL pin selection bit
0 : Connect to ports P2
1 : Connect to ports P2
data.
2
4
, P2
, P2
3
5
•Bit 6: SDA/SCL pin selection bit
This bit selects the input/output pins of SCL and SDA of the multi-
2
I2C-BUS interface pin input
level selection bit
0 : CMOS input
master I C-BUS interface.
2
•Bit 7: I C-BUS interface pin input level selection bit
This bit selects the input level of the SCL and SDA pins of the
1 : SMBUS input
2
multi-master I C-BUS interface.
2
Fig. 31 Structure of I C control register
32
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
2
[I C Status Register (S1)] 002D16
•Bit 4: SCL pin low hold bit (PIN)
2
2
The I C status register (address 002D16) controls the I C-BUS in-
terface status. The low-order 4 bits are read-only bits and the
high-order 4 bits can be read out and written to.
This bit generates an interrupt request signal. Each time 1-byte
data is transmitted, the PIN bit changes from “1” to “0.” At the
same time, an interrupt request signal occurs to the CPU. The PIN
bit is set to “0” in synchronization with a falling of the last clock (in-
cluding the ACK clock) of an internal clock and an interrupt
request signal occurs in synchronization with a falling of the PIN
bit. When the PIN bit is “0,” the SCL is kept in the “0” state and
clock generation is disabled. Figure 33 shows an interrupt request
signal generating timing chart.
Set “00002” to the low-order 4 bits, because these bits become the
reserved bits at writing.
•Bit 0: Last receive bit (LRB)
This bit stores the last bit value of received data and can also be
used for ACK receive confirmation. If ACK is returned when an
ACK clock occurs, the LRB bit is set to “0.” If ACK is not returned,
this bit is set to “1.” Except in the ACK mode, the last bit value of
received data is input. The state of this bit is changed from “1” to
The PIN bit is set to “1” in one of the following conditions:
2
• Executing a write instruction to the I C data shift register (ad-
2
“0” by executing a write instruction to the I C data shift register
dress 002B16). (This is the only condition which the prohibition of
the internal clock is released and data can be communicated ex-
cept for the start condition detection.)
(address 002B16).
•Bit 1: General call detecting flag (AD0)
✽
When the ALS bit is “0”, this bit is set to “1” when a general call
whose address data is all “0” is received in the slave mode. By a
general call of the master device, every slave device receives con-
trol data after the general call. The AD0 bit is set to “0” by
detecting the STOP condition or START condition, or reset.
• When the ES0 bit is “0”
• At reset
• When writing “1” to the PIN bit by software
The conditions in which the PIN bit is set to “0” are shown below:
• Immediately after completion of 1-byte data transmission (includ-
ing when arbitration lost is detected)
✽General call: The master transmits the general call address “0016” to all
• Immediately after completion of 1-byte data reception
• In the slave reception mode, with ALS = “0” and immediately af-
ter completion of slave address agreement or general call
address reception
slaves.
•Bit 2: Slave address comparison flag (AAS)
This flag indicates a comparison result of address data when the
ALS bit is “0”.
• In the slave reception mode, with ALS = “1” and immediately af-
ter completion of address data reception
✽ In the slave receive mode, when the 7-bit addressing format is
selected, this bit is set to “1” in one of the following conditions:
• The address data immediately after occurrence of a START
condition agrees with the slave address stored in the high-or-
•Bit 5: Bus busy flag (BB)
This bit indicates the status of use of the bus system. When this
bit is set to “0,” this bus system is not busy and a START condition
can be generated. The BB flag is set/reset by the SCL, SDA pins
input signal regardless of master/slave. This flag is set to “1” by
detecting the start condition, and is set to “0” by detecting the stop
condition. The condition of these detecting is set by the start/stop
2
der 7 bits of the I C address register (address 002C16).
• A general call is received.
✽ In the slave receive mode, when the 10-bit addressing format is
selected, this bit is set to “1” with the following condition:
2
condition setting bits (SSC4–SSC0) of the I C start/stop condition
2
• When the address data is compared with the I C address reg-
2
control register (address 003016). When the ES0 bit of the I C
ister (8 bits consisting of slave address and RWB bit), the first
bytes agree.
control register (address 002E16) is “0” or reset, the BB flag is set
to “0.”
2
✽✽This bit is set to “0” by executing a write instruction to the I C
For the writing function to the BB flag, refer to the sections
“START Condition Generating Method” and “STOP Condition Gen-
erating Method” described later.
data shift register (address 002B16) when ES0 is set to “1” or
reset.
✽
•Bit 3: Arbitration lost detecting flag (AL)
In the master transmission mode, when the SDA is made “L” by
any other device, arbitration is judged to have been lost, so that
this bit is set to “1.” At the same time, the TRX bit is set to “0,” so
that immediately after transmission of the byte whose arbitration
was lost is completed, the MST bit is set to “0.” The arbitration lost
can be detected only in the master transmission mode. When ar-
bitration is lost during slave address transmission, the TRX bit is
set to “0” and the reception mode is set. Consequently, it becomes
possible to detect the agreement of its own slave address and ad-
dress data transmitted by another master device.
✽Arbitration lost :The status in which communication as a master is dis-
abled.
33
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
•Bit 6: Communication mode specification bit (transfer direc-
tion specification bit: TRX)
b7
b0
This bit decides a direction of transfer for data communication.
When this bit is “0,” the reception mode is selected and the data of
a transmitting device is received. When the bit is “1,” the transmis-
sion mode is selected and address data and control data are
output onto the SDA in synchronization with the clock generated
on the SCL.
I2C status register
(S1 : address 002D16)
MST TRX BB PIN AL AAS AD0 LRB
Last receive bit (Note)
0 : Last bit = “0”
1 : Last bit = “1”
This bit is set/reset by software and hardware. About set/reset by
hardware is described below. This bit is set to “1” by hardware
when all the following conditions are satisfied:
General call detecting flag
(Note)
0 : No general call detected
1 : General call detected
• When ALS is “0”
• In the slave reception mode or the slave transmission mode
• When the R/W bit reception is “1”
Slave address comparison flag
(Note)
This bit is set to “0” in one of the following conditions:
• When arbitration lost is detected.
0 : Address disagreement
1 : Address agreement
• When a STOP condition is detected.
Arbitration lost detecting flag
(Note)
0 : Not detected
1 : Detected
• When writing “1” to this bit by software is invalid by the START
condition duplication preventing function (Note).
• With MST = “0” and when a START condition is detected.
• With MST = “0” and when ACK non-return is detected.
• At reset
SCL pin low hold bit
0 : SCL pin low hold
1 : SCL pin low release
•Bit 7: Communication mode specification bit (master/slave
specification bit: MST)
This bit is used for master/slave specification for data communica-
tion. When this bit is “0,” the slave is specified, so that a START
condition and a STOP condition generated by the master are re-
ceived, and data communication is performed in synchronization
with the clock generated by the master. When this bit is “1,” the
master is specified and a START condition and a STOP condition
are generated. Additionally, the clocks required for data communi-
cation are generated on the SCL.
Bus busy flag
0 : Bus free
1 : Bus busy
Communication mode
specification bits
00 : Slave receive mode
01 : Slave transmit mode
10 : Master receive mode
11 : Master transmit mode
This bit is set to “0” in one of the following conditions.
• Immediately after completion of 1-byte data transfer when arbi-
tration lost is detected
Note: These bits and flags can be read out, but cannot
be written.
Write “0” to these bits at writing.
• When a STOP condition is detected.
• Writing “1” to this bit by software is invalid by the START condi-
tion duplication preventing function (Note).
2
• At reset
Fig. 32 Structure of I C status register
Note: START condition duplication preventing function
The MST, TRX, and BB bits is set to “1” at the same time after con-
firming that the BB flag is “0” in the procedure of a START condition
occurrence. However, when a START condition by another master
device occurs and the BB flag is set to “1” immediately after the con-
tents of the BB flag is confirmed, the START condition duplication
preventing function makes the writing to the MST and TRX bits in-
valid. The duplication preventing function becomes valid from the
rising of the BB flag to reception completion of slave address.
S
CL
PIN
IICIRQ
Fig. 33 Interrupt request signal generating timing
34
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
START Condition Generating Method
START/STOP Condition Detecting Operation
The START/STOP condition detection operations are shown in
Figures 36, 37, and Table 11. The START/STOP condition is set
by the START/STOP condition set bit.
2
When writing “1” to the MST, TRX, and BB bits of the I C status
register (address 002D16) at the same time after writing the slave
2
address to the I C data shift register (address 002B16) with the
2
condition in which the ES0 bit of the I C control register (address
The START/STOP condition can be detected only when the input
signal of the SCL and SDA pins satisfy three conditions: SCL re-
lease time, setup time, and hold time (see Table 11).
The BB flag is set to “1” by detecting the START condition and is
reset to “0” by detecting the STOP condition.
002E16) and the BB flag are “0”, a START condition occurs. After
that, the bit counter becomes “0002” and an SCL for 1 byte is out-
put. The START condition generating timing is different in the
standard clock mode and the high-speed clock mode. Refer to
Figure 34, the START condition generating timing diagram, and
Table 9, the START condition generating timing table.
The BB flag set/reset timing is different in the standard clock mode
and the high-speed clock mode. Refer to Table 11, the BB flag set/
reset time.
Note: When a STOP condition is detected in the slave mode (MST = 0), an
interrupt request signal “IICIRQ” occurs to the CPU.
I2C status register
write signal
S
S
CL
DA
Setup
time
SCL release time
Hold time
SCL
Setup
Hold time
time
SDA
BB flag
reset
time
Fig. 34 START condition generating timing diagram
Table 9 START condition generating timing table
BB flag
Fig. 36 START condition detecting timing diagram
Standard clock mode High-speed clock mode
Item
5.0 µs (20 cycles)
5.0 µs (20 cycles)
2.5 µs (10 cycles)
2.5 µs (10 cycles)
Setup time
Hold time
S
CL release time
S
CL
DA
Setup
time
Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the
number of φ cycles.
Hold time
S
BB flag
reset
time
BB flag
STOP Condition Generating Method
2
When the ES0 bit of the I C control register (address 002E16) is
Fig. 37 STOP condition detecting timing diagram
“1,” write “1” to the MST and TRX bits, and write “0” to the BB bit
2
of the I C status register (address 002D16) simultaneously. Then a
Table 11 START condition/STOP condition detecting conditions
STOP condition occurs. The STOP condition generating timing is
different in the standard clock mode and the high-speed clock
mode. Refer to Figure 35, the STOP condition generating timing
diagram, and Table 10, the STOP condition generating timing
table.
Standard clock mode
High-speed clock mode
S
CL release time
SSC value + 1 cycle (6.25 µs)
4 cycles (1.0 µs)
SSC value + 1
Setup time
Hold time
cycle < 4.0 µs (3.125 µs)
2 cycles (1.0 µs)
2 cycles (0.5 µs)
2
SSC value + 1
cycle < 4.0 µs (3.125 µs)
2
I2C status register
write signal
BB flag set/
reset time
SSC value –1
3.5 cycles (0.875 µs)
+ 2 cycles (3.375 µs)
2
Note: Unit : Cycle number of system clock φ
SCL
Setup
time
SSC value is the decimal notation value of the START/STOP condi-
tion set bits SSC4 to SSC0. Do not set “0” or an odd number to SSC
value. The value in parentheses is an example when the I2C START/
STOP condition control register is set to “1816” at φ = 4 MHz.
Hold time
SDA
Fig. 35 STOP condition generating timing diagram
Table 10 STOP condition generating timing table
Standard clock mode
5.0 µs (20 cycles)
4.5 µs (18 cycles)
High-speed clock mode
3.0 µs (12 cycles)
Item
Setup time
Hold time
2.5 µs (10 cycles)
Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the
number of φ cycles.
35
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
2
[I C START/STOP Condition Control Register
Address Data Communication
(S2D)] 003016
The I C START/STOP condition control register (address 003016)
There are two address data communication formats, namely, 7-bit
addressing format and 10-bit addressing format. The respective
address communication formats are described below.
✽ 7-bit addressing format
2
controls START/STOP condition detection.
•Bits 0 to 4: START/STOP condition set bit (SSC4–SSC0)
SCL release time, setup time, and hold time change the detection
condition by value of the main clock divide ratio selection bit and
the oscillation frequency f(XIN) because these time are measured
by the internal system clock. Accordingly, set the proper value to
the START/STOP condition set bits (SSC4 to SSC0) in considered
of the system clock frequency. Refer to Table 11.
To adapt the 7-bit addressing format, set the 10BIT SAD bit of
2
the I C control register (address 002E16) to “0.” The first 7-bit
address data transmitted from the master is compared with the
2
high-order 7-bit slave address stored in the I C address register
(address 002C16). At the time of this comparison, address com-
2
parison of the RWB bit of the I C address register (address
Do not set “000002” or an odd number to the START/STOP condi-
tion set bit (SSC4 to SSC0).
002C16) is not performed. For the data transmission format
when the 7-bit addressing format is selected, refer to Figure 39,
(1) and (2).
Refer to Table 12, the recommended set value to START/STOP
condition set bits (SSC4–SSC0) for each oscillation frequency.
•Bit 5: SCL/SDA interrupt pin polarity selection bit (SIP)
An interrupt can occur when detecting the falling or rising edge of
the SCL or SDA pin. This bit selects the polarity of the SCL or
SDA pin interrupt pin.
✽ 10-bit addressing format
To adapt the 10-bit addressing format, set the 10BIT SAD bit of
2
the I C control register (address 002E16) to “1.” An address
comparison is performed between the first-byte address data
transmitted from the master and the 8-bit slave address stored
2
•Bit 6: SCL/SDA interrupt pin selection bit (SIS)
in the I C address register (address 002C16). At the time of this
This bit selects the pin of which interrupt becomes valid between
comparison, an address comparison between the RWB bit of
2
the SCL pin and the SDA pin.
the I C address register (address 002C16) and the R/W bit
Note: When changing the setting of the SCL/SDA interrupt pin polarity se-
lection bit, the SCL/SDA interrupt pin selection bit, or the I2C-BUS
interface enable bit ES0, the SCL/SDA interrupt request bit may be
set. When selecting the SCL/SDA interrupt source, disable the inter-
rupt before the SCL/SDA interrupt pin polarity selection bit, the SCL/
SDA interrupt pin selection bit, or the I2C-BUS interface enable bit
ES0 is set. Reset the request bit to “0” after setting these bits, and
enable the interrupt.
which is the last bit of the address data transmitted from the
master is made. In the 10-bit addressing mode, the RWB bit
which is the last bit of the address data not only specifies the
direction of communication for control data, but also is pro-
cessed as an address data bit.
When the first-byte address data agree with the slave address,
2
the AAS bit of the I C status register (address 002D16) is set to
2
“1.” After the second-byte address data is stored into the I C
data shift register (address 002B16), perform an address com-
parison between the second-byte data and the slave address
by software. When the address data of the 2 bytes agree with
2
the slave address, set the RWB bit of the I C address register
(address 002C16) to “1” by software. This processing can make
the 7-bit slave address and R/W data agree, which are re-
ceived after a RESTART condition is detected, with the value of
2
the I C address register (address 002C16). For the data trans-
mission format when the 10-bit addressing format is selected,
refer to Figure 39, (3) and (4).
36
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
I2C START/STOP condition
control register
SSC4 SSC3 SSC2 SSC1 SSC0
SIS SIP
(S2D : address 003016)
START/STOP condition set bit
SCL/SDA interrupt pin polarity
selection bit
0 : Falling edge active
1 : Rising edge active
SCL/SDA interrupt pin selection bit
0 : SDA valid
1 : SCL valid
Reserved
Do not write “1” to this bit.
2
Fig. 38 Structure of I C START/STOP condition control register
Table 12 Recommended set value to START/STOP condition set bits (SSC4–SSC0) for each oscillation frequency
Oscillation
frequency
f(XIN) (MHz)
START/STOP
condition
control register
System
clock φ
(MHz)
Main clock
divide ratio
SCL release time
Setup time
Hold time
(µs)
(µs)
(µs)
3.375 µs (13.5 cycles)
3.125 µs (12.5 cycles)
2.5 µs (2.5 cycles)
3.25 µs (6.5 cycles)
2.75 µs (5.5 cycles)
2.5 µs (2.5 cycles)
XXX11010
XXX11000
XXX00100
XXX01100
XXX01010
XXX00100
6.75 µs (27 cycles)
6.25 µs (25 cycles)
5.0 µs (5 cycles)
6.5 µs (13 cycles)
5.5 µs (11 cycles)
5.0 µs (5 cycles)
3.375 µs (13.5 cycles)
3.125 µs (12.5 cycles)
2.5 µs (2.5 cycles)
3.25 µs (6.5 cycles)
2.75 µs (5.5 cycles)
2.5 µs (2.5 cycles)
8
8
4
2
2
8
2
2
4
1
2
1
Note: Do not set an odd number to the START/STOP condition set bit (SSC4 to SSC0).
(1) A master-transmitter transnmits data to a slave-receiver
A
Data
A
Data
S
Slave address R/W
7 bits “0”
A/A
A
P
P
1 to 8 bits
1 to 8 bits
(2) A master-receiver receives data from a slave-transmitter
A
Data
A
Data
S
Slave address R/W
7 bits “1”
1 to 8 bits
1 to 8 bits
(3) A master-transmitter transmits data to a slave-receiver with a 10-bit address
Slave address
2nd bytes
Slave address
1st 7 bits
A/A
A
A
Data
Data
S
R/W
A
P
1 to 8 bits
1 to 8 bits
7 bits
“0”
8 bits
(4) A master-receiver receives data from a slave-transmitter with a 10-bit address
Slave address
2nd bytes
Slave address
1st 7 bits
Slave address
1st 7 bits
Sr
A
A
A
Data
1 to 8 bits
Data
P
S
R/W
R/W
A
A
“1”
1 to 8 bits
7 bits
“0”
8 bits
7 bits
S : START condition
A : ACK bit
Sr : Restart condition
P : STOP condition
R/W : Read/Write bit
: Master to slave
: Slave to master
Fig. 39 Address data communication format
37
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Example of Master Transmission
An example of master transmission in the standard clock mode, at
the SCL frequency of 100 kHz and in the ACK return mode is
shown below.
2
✽ Set a slave address in the high-order 7 bits of the I C address
register (address 002C16) and “0” into the RWB bit.
✽ Set the ACK return mode and SCL = 100 kHz by setting “8516”
2
in the I C clock control register (address 002F16).
2
✽ Set “0016” in the I C status register (address 002D16) so that
transmission/reception mode can become initializing condition.
2
✽ Set a communication enable status by setting “0816” in the I C
control register (address 002E16).
2
✽ Confirm the bus free condition by the BB flag of the I C status
register (address 002D16).
✽ Set the address data of the destination of transmission in the
2
high-order 7 bits of the I C data shift register (address 002B16)
and set “0” in the least significant bit.
2
✽ Set “F016” in the I C status register (address 002D16) to gener-
ate a START condition. At this time, an SCL for 1 byte and an
ACK clock automatically occur.
2
✽ Set transmit data in the I C data shift register (address 002B16).
At this time, an SCL and an ACK clock automatically occur.
✽ When transmitting control data of more than 1 byte, repeat step
✽.
2
✽ Set “D016” in the I C status register (address 002D16) to gener-
ate a STOP condition if ACK is not returned from slave
reception side or transmission ends.
Example of Slave Reception
An example of slave reception in the high-speed clock mode, at
the SCL frequency of 400 kHz, in the ACK non-return mode and
using the addressing format is shown below.
2
✽ Set a slave address in the high-order 7 bits of the I C address
register (address 002C16) and “0” in the RWB bit.
✽ Set the no ACK clock mode and SCL = 400 kHz by setting
2
“2516” in the I C clock control register (address 002F16).
2
✽ Set “0016” in the I C status register (address 002D16) so that
transmission/reception mode can become initializing condition.
2
✽ Set a communication enable status by setting “0816” in the I C
control register (address 002E16).
✽ When a START condition is received, an address comparison is
performed.
✽✽•When all transmitted addresses are “0” (general call):
2
AD0 of the I C status register (address 002D16) is set to “1”
and an interrupt request signal occurs.
• When the transmitted addresses agree with the address set
in ✽:
2
AAS of the I C status register (address 002D16) is set to “1”
and an interrupt request signal occurs.
2
• In the cases other than the above AD0 and AAS of the I C sta-
tus register (address 002D16) are set to “0” and no interrupt
request signal occurs.
2
✽ Set dummy data in the I C data shift register (address 002B16).
✽ When receiving control data of more than 1 byte, repeat step ✽.
✽ When a STOP condition is detected, the communication ends.
38
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
2
✽Precautions when using multi-master I C-
5. Disable interrupts during the following three process steps:
• BB flag confirming
BUS interface
(1) Read-modify-write instruction
• Writing of slave address value
The precautions when the read-modify-write instruction such as
SEB, CLB etc. is executed for each register of the multi-master
• Trigger of START condition generating
When the condition of the BB flag is bus busy, enable interrupts
immediately.
2
I C-BUS interface are described below.
2
• I C data shift register (S0: address 002B16)
When executing the read-modify-write instruction for this regis-
ter during transfer, data may become a value not intended.
(3) RESTART condition generating procedure
1. Procedure example (The necessary conditions for the proce-
dure are described in items 2 to 4 below.)
2
• I C address register (S0D: address 002C16)
When the read-modify-write instruction is executed for this regis-
ter at detecting the STOP condition, data may become a value
not intended. It is because H/W changes the read/write bit
(RWB) at the above timing.
Execute the following procedure when the PIN bit is “0.”
•
•
•
LDM #$00, S1
LDA —
(Select slave receive mode)
(Take out of slave address value)
(Disable interrupt)
2
• I C status register (S1: address 002D16)
SEI
Do not execute the read-modify-write instruction for this register
because all bits of this register are changed by H/W.
STAS0
(Write slave address value)
LDM #$F0, S1
CLI
(Trigger RESTART condition generation
)
2
• I C control register (S1D: address 002E16)
(Enable interrupt)
•
•
•
When the read-modify-write instruction is executed for this regis-
ter at detecting the START condition or at completing the byte
transfer, data may become a value not intended. Because H/W
changes the bit counter (BC0-BC2) at the above timing.
2. Select the slave receive mode when the PIN bit is “0.” Do not
write “1” to the PIN bit. Neither “0” nor “1” is specified as input to
the BB bit.
2
• I C clock control register (S2: address 002F16)
The TRX bit becomes “0” and the SDA pin is released.
3. The SCL pin is released by writing the slave address value to
The read-modify-write instruction can be executed for this regis-
2
ter.
the I C data shift register.
2
• I C START/STOP condition control register (S2D: address
4. Disable interrupts during the following two process steps:
• Write slave address value
003016)
The read-modify-write instruction can be executed for this regis-
ter.
• Trigger RESTART condition generation
2
(4) Writing to I C status register
(2) START condition generating procedure using multi-master
1. Procedure example (The necessary conditions of the generat-
ing procedure are described in Items 2 to 5 below.
Do not execute an instruction to set the PIN bit to “1” from “0” and
an instruction to set the MST and TRX bits to “0” from “1” simulta-
neously. Because it may enter the state that the SCL pin is
released and the SDA pin is released after about one machine
cycle. Do not execute an instruction to set the MST and TRX bits
to “0” from “1” simultaneously when the PIN bit is “1.” Because it
may become the same as above.
•
•
•
LDA —
(Taking out of slave address value)
(Interrupt disabled)
SEI
BBS 5, S1, BUSBUSY (BB flag confirming and branch process)
BUSFREE:
STA S0
(Writing of slave address value)
(Trigger of START condition generating)
(Interrupt enabled)
(5) Process of after STOP condition generating
2
2
LDM #$F0, S1
CLI
Do not write data in the I C data shift register S0 and the I C sta-
tus register S1 until the bus busy flag BB becomes “0” after
generating the STOP condition in the master mode. Because the
STOP condition waveform might not be normally generated.
Reading to the above registers do not have the problem.
•
•
•
BUSBUSY:
CLI
(Interrupt enabled)
•
•
•
2. Use “Branch on Bit Set” of “BBS 5, $002D, –” for the BB flag
confirming and branch process.
3. Use “STA $2B, STX $2B” or “STY $2B” of the zero page ad-
dressing instruction for writing the slave address value to the
2
I C data shift register.
4. Execute the branch instruction of Item 2 and the store instruc-
tion of Item 3 continuously, as shown in the procedure example
above.
39
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PULSE WIDTH MODULATION (PWM)
The 7516 group (Spec. H) has a PWM function with an 8-bit reso-
lution, based on a signal that is the clock input XIN or that clock
input divided by 2.
PWM Operation
When bit 0 (PWM enable bit) of the PWM control register is set to
“1”, operation starts by initializing the PWM output circuit, and
pulses are output starting at an “H”.
If the PWM register or PWM prescaler is updated during PWM
output, the pulses will change in the cycle after the one in which
the change was made.
Data Setting
The PWM output pin also functions as port P44. Set the PWM
period by the PWM prescaler, and set the “H” term of output pulse
by the PWM register.
If the value in the PWM prescaler is n and the value in the PWM
register is m (where n = 0 to 255 and m = 0 to 255) :
PWM period = 255 ✽ (n+1) / f(XIN)
31.875 ✽ m ✽ (n+1)
µs
255
= 31.875 ✽ (n+1) µs
PWM output
(when f(XIN) = 8 MHz,count source selection bit = “0”)
Output pulse “H” term = PWM period ✽ m / 255
= 0.125 ✽ (n+1) ✽ m µs
T = [31.875 ✽ (n+1)] µs
(when f(XIN) = 8 MHz,count source selection bit = “0”)
m: Contents of PWM register
n : Contents of PWM prescaler
T : PWM period (when f(XIN) = 8 MHz, count
source selection bit = “0”)
Fig. 40 Timing of PWM period
Data bus
PWM
prescaler pre-latch
PWM
register pre-latch
Transfer control circuit
PWM
prescaler latch
PWM
register latch
Count source
selection bit
Port P4
4
“0”
X
IN
PWM prescaler
PWM register
(XCIN at low-speed mode)
“1”
1/2
Port P44 latch
PWM enable bit
Fig. 41 Block diagram of PWM function
40
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
PWM control register
(PWMCON : address 001D16)
PWM function enable bit
0: PWM disabled
1: PWM enabled
Count source selection bit
0: f(XIN) (f(XCIN) at low-speed mode)
1: f(XIN)/2 (f(XCIN)/2 at low-speed mode)
Not used (return “0” when read)
Fig. 42 Structure of PWM control register
B
T
C
T2
=
A
B
C
PWM output
T
T
T2
PWM register
write signal
(Changes “H” term from “A” to “B”.)
PWM prescaler
write signal
(Changes PWM period from “T” to “T2”.)
When the contents of the PWM register or PWM prescaler have changed, the PWM
output will change from the next period after the change.
Fig. 43 PWM output timing when PWM register or PWM prescaler is changed
✽Note
The PWM starts after the PWM function enable bit is set to enable and “L” level is output from the PWM pin.
The length of this “L” level output is as follows:
n+1
sec
sec
(Count source selection bit = 0, where n is the value set in the prescaler)
(Count source selection bit = 1, where n is the value set in the prescaler)
2 • f(XIN)
n+1
f(XIN)
41
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
A-D CONVERTER
[A-D Conversion Registers (ADL, ADH)]
003516, 003616
The A-D conversion registers are read-only registers that store the
result of an A-D conversion. Do not read these registers during an
A-D conversion.
b0
b7
AD control register
(ADCON : address 003416
)
Analog input pin selection bits
b2 b1 b0
0 0 0: P3
0 0 1: P3
0 1 0: P3
0 1 1: P3
1 0 0: P3
1 0 1: P3
0/AN
1/AN
2/AN
3/AN
4/AN
5/AN
0
1
2
3
4
5
[AD Control Register (ADCON)] 003416
The AD control register controls the A-D conversion process. Bits
0 to 2 select a specific analog input pin. Bit 4 indicates the
completion of an A-D conversion. The value of this bit remains at
“0” during an A-D conversion and changes to “1” when an A-D
conversion ends. Writing “0” to this bit starts the A-D conversion.
1 1 0: Setting disabled
1 1 1: Setting disabled
Not used (returns “0” when read)
A-D conversion completion bit
0: Conversion in progress
1: Conversion completed
Comparison Voltage Generator
The comparison voltage generator divides the voltage between
Not used (returns “0” when read)
Fig. 44 Structure of AD control register
AVSS and VREF into 1024 and outputs the divided voltages.
Channel Selector
The channel selector selects one of ports P30/AN0 to P35/AN5 and
10-bit reading
inputs the voltage to the comparator.
(Read address 003616 before 003516
)
b7
b0
(Address 003616
)
)
Comparator and Control Circuit
b9 b8
The comparator and control circuit compare an analog input volt-
age with the comparison voltage, and the result is stored in the
A-D conversion registers. When an A-D conversion is completed,
the control circuit sets the A-D conversion completion bit and the
A-D interrupt request bit to “1”.
b0
b7
b7 b6 b5 b4 b3 b2 b1 b0
(Address 003516
Note : The high-order 6 bits of address 003616 become “0”
at reading.
Note that because the comparator consists of a capacitor cou-
pling, set f(XIN) to 500 kHz or more during an A-D conversion.
When the A-D converter is operated at low-speed mode, f(XIN)
and f(XCIN) do not have the lower limit of frequency, because of
the A-D converter has a built-in self-oscillation circuit.
8-bit reading (Read only address 003516
)
b7
b0
(Address 003516
)
b9 b8 b7 b6 b5 b4 b3 b2
Fig. 45 Structure of A-D conversion registers
Data bus
b7
3
b0
AD control register
(Address 003416
)
A-D interrupt request
A-D control circuit
P30/AN0
A-D conversion high-order register (Address 003616
)
)
P31/AN
1
Comparator
A-D conversion low-order register
(Address 003516
P32/AN
2
P3
P3
P3
3
/AN
/AN
/AN
3
10
4
4
Resistor ladder
5
5
V
REF AVSS
Fig. 46 Block diagram of A-D converter
42
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
WATCHDOG TIMER
✽Watchdog timer H count source selection bit operation
Bit 7 of the watchdog timer control register (address 003916) per-
mits selecting a watchdog timer H count source. When this bit is
set to “0”, the count source becomes the underflow signal of
watchdog timer L. The detection time is set to 131.072 ms at f(XIN)
= 8 MHz frequency and 32.768 s at f(XCIN) = 32 kHz frequency.
When this bit is set to “1”, the count source becomes the signal
divided by 16 for f(XIN) (or f(XCIN)). The detection time in this case
is set to 512 µs at f(XIN) = 8 MHz frequency and 128 ms at f(XCIN)
= 32 kHz frequency. This bit is cleared to “0” after reset.
The watchdog timer gives a mean of returning to the reset status
when a program cannot run on a normal loop (for example, be-
cause of a software run-away). The watchdog timer consists of an
8-bit watchdog timer L and an 8-bit watchdog timer H.
Standard Operation of Watchdog Timer
When any data is not written into the watchdog timer control reg-
ister (address 003916) after reset, the watchdog timer is in the
stop state. The watchdog timer starts to count down by writing an
optional value into the watchdog timer control register (address
003916) and an internal reset occurs at an underflow of the watch-
dog timer H.
✽Operation of STP instruction disable bit
Bit 6 of the watchdog timer control register (address 003916) per-
mits disabling the STP instruction when the watchdog timer is in
operation.
Accordingly, programming is usually performed so that writing to
the watchdog timer control register (address 003916) may be
started before an underflow. When the watchdog timer control reg-
ister (address 003916) is read, the values of the high-order 6 bits
of the watchdog timer H, STP instruction disable bit, and watch-
dog timer H count source selection bit are read.
When this bit is “0”, the STP instruction is enabled.
When this bit is “1”, the STP instruction is disabled, once the STP
instruction is executed, an internal reset occurs. When this bit is
set to “1”, it cannot be rewritten to “0” by program. This bit is
cleared to “0” after reset.
✽Initial value of watchdog timer
At reset or writing to the watchdog timer control register (address
003916), each watchdog timer H and L are set to “FF16.”
“FF16” is set when
watchdog timer
Data bus
“FF16” is set when
watchdog timer
control register is
X
CIN
control register is
written to.
“0”
“10”
written to.
Watchdog timer L (8)
Main clock division
ratio selection bits
(Note)
Watchdog timer H (8)
1/16
“1”
“00”
“01”
Watchdog timer H count
source selection bit
X
IN
STP instruction disable bit
STP instruction
Reset
circuit
Internal reset
RESET
Note: Any one of high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register.
Fig. 47 Block diagram of Watchdog timer
b0
b7
Watchdog timer control register
(WDTCON : address 003916
)
Watchdog timer H (for read-out of high-order 6 bit)
STP instruction disable bit
0: STP instruction enabled
1: STP instruction disabled
Watchdog timer H count source selection bit
0: Watchdog timer L underflow
1: f(XIN)/16 or f(XCIN)/16
Fig. 48 Structure of Watchdog timer control register
43
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec.H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
RESET CIRCUIT
To reset the microcomputer, RESET pin must be held at an “L”
level for 20 cycles or more of XIN. Then the RESET pin is returned
to an “H” level (the power source voltage must be between 2.7 V
and 5.5 V, and the oscillation must be stable), reset is released.
After the reset is completed, the program starts from the address
contained in address FFFD16 (high-order byte) and address
FFFC16 (low-order byte). Make sure that the reset input voltage is
less than 0.54 V for VCC of 2.7 V.
Poweron
(Note)
Power source
voltage
0V
RESET
VCC
Reset input
voltage
0V
0.2VCC
Note : Reset release voltage; Vcc = 2.7 V
RESET
VCC
Power source
voltage detection
circuit
Fig. 49 Reset circuit example
X
IN
φ
RESET
RESETOUT
Address
AD
H,L
?
?
?
?
FFFC
FFFD
Reset address from the vector table.
AD
H
Data
?
?
?
AD
L
?
SYNC
X
IN: 8 to 13 clock cycles
Notes1: The frequency relation of f(XIN) and f(φ) is f(XIN) = 8 • f(φ).
2: The question marks (?) indicate an undefined state that depends on the previous state.
3: All signals except XIN and RESET are internals.
Fig. 50 Reset sequence
44
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec.H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Address Register contents
Register contents
Address
(1)
Port P0 (P0)
000016
000116
000216
000316
000416
000516
000616
000716
000816
000916
001516
001616
001716
(37) A-D control register (ADCON)
(38) A-D conversion low-order register (ADL)
(39) A-D conversion high-order register (ADH)
(40) MISRG
0016
0 0 0 1 0 0 0 0
X X X X X X X X
003416
003516
(2)
Port P0 direction register (P0D)
Port P1 (P1)
0016
(3)
0016
003616 0 0 0 0 0 0 X X
(4)
Port P1 direction register (P1D)
Port P2 (P2)
0016
003816
003916
003A16
003B16
003C16
003D16
003E16
003F16
(PS)
0016
Watchdog timer control register (WDTCON)
(41)
(5)
0016
0 0 1 1 1 1 1 1
0016
(6)
Port P2 direction register (P2D)
Port P3 (P3)
(42) Interrupt edge selection register (INTEDGE)
(43) CPU mode register (CPUM)
0016
(7)
0016
0 1 0 0 1 0 0 0
0016
Interrupt request register 1 (IREQ1)
(44)
(8)
Port P3 direction register (P3D)
Port P4 (P4)
0016
0016
Interrupt request register 2 (IREQ2)
(45)
(9)
0016
0016
Interrupt control register 1 (ICON1)
(46)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
(27)
(28)
(29)
(30)
(31)
(32)
(33)
(34)
(35)
(36)
Port P4 direction register (P4D)
Serial I/O2 control register 1 (SIO2CON1)
Serial I/O2 control register 2 (SIO2CON2)
Serial I/O2 register (SIO2)
Transmit/Receive buffer register (TB/RB)
Serial I/O1 status register (SIOSTS)
Serial I/O1 control register (SIOCON)
UART control register (UARTCON)
Baud rate generator (BRG)
PWM control register (PWMCON)
PWM prescaler (PREPWM)
PWM register (PWM)
0016
Interrupt control register 2 (ICON2)
(47)
0016
0016
(48) Processor status register
(49) Program counter
0 0 0 0 0 1 1 1
X X X X X X X X
X X X X X 1 X X
FFFD16 contents
FFFC16 contents
(PCH)
001816 X X X X X X X X
(PC
L
)
001916
001A16
001B16
1 0 0 0 0 0 0 0
0016
Note : X : Not fixed
Since the initial values for other than above mentioned registers and
RAM contents are indefinite at reset, they must be set.
1 1 1 0 0 0 0 0
001C16 X X X X X X X X
001D16
001E16
0016
X X X X X X X X
001F16 X X X X X X X X
Prescaler 12 (PRE12)
002016
002116
002216
002316
002416
002516
002616
002716
002816
002B16
002C16
002D16
002E16
002F16
003016
FF16
Timer 1 (T1)
0116
Timer 2 (T2)
0016
Timer XY mode register (TM)
Prescaler X (PREX)
0016
FF16
Timer X (TX)
FF16
Prescaler Y (PREY)
FF16
Timer Y (TY)
FF16
0016
Timer count source selection register (TCSS)
I2C data shift register (S0)
I2C address regiter (S0D)
I2C status register (S1)
X X X X X X X X
0016
0 0 0 1 0 0 0
X
I2C control register (S1D)
I2C clock control register (S2)
0016
0016
2
0 0 0
X X X
X
X
I C start/stop condition control register (S2D)
Fig. 51 Internal status at reset
45
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec.H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
RESET pin until the oscillation is stable since a wait time will not
be generated.
CLOCK GENERATING CIRCUIT
The 7516 group (Spec H) has two built-in oscillation circuits: main
clock XIN-XOUT oscillation circuit and sub clock XCIN-XCOUT oscil-
lation circuit. An oscillation circuit can be formed by connecting a
resonator between XIN and XOUT (XCIN and XCOUT). Use the cir-
cuit constants in accordance with the resonator manufacturer’s
recommended values. No external resistor is needed between XIN
and XOUT since a feed-back resistor exists on-chip. However, an
external feed-back resistor is needed between XCIN and XCOUT.
Immediately after power on, only the XIN oscillation circuit starts
oscillating, and XCIN and XCOUT pins function as I/O ports.
(2) Wait mode
If the WIT instruction is executed, the internal clock φ stops at an
“H” level, but the oscillator does not stop. The internal clock φ re-
starts at reset or when an interrupt is received. Since the oscillator
does not stop, normal operation can be started immediately after
the clock is restarted.
To ensure that the interrupts will be received to release the STP or
WIT state, their interrupt enable bits must be set to “1” before ex-
ecuting of the STP or WIT instruction.
Frequency Control
(1) Middle-speed mode
When releasing the STP state, the prescaler 12 and timer 1 will
start counting the clock XIN divided by 16. Accordingly, set the
timer 1 interrupt enable bit to “0” before executing the STP instruc-
tion.
The internal clock φ is the frequency of XIN divided by 8. After re-
set is released, this mode is selected.
(2) High-speed mode
The internal clock φ is half the frequency of XIN.
✽Note
When using the oscillation stabilizing time set after STP instruction
released bit set to “1”, evaluate time to stabilize oscillation of the
used oscillator and set the value to the timer 1 and prescaler 12.
(3) Low-speed mode
The internal clock φ is half the frequency of XCIN.
✽Note
If you switch the mode between middle/high-speed and low-
speed, stabilize both XIN and XCIN oscillations. The sufficient time
is required for the sub-clock to stabilize, especially immediately af-
ter power on and at returning from the stop mode. When switching
the mode between middle/high-speed and low-speed, set the fre-
quency on condition that f(XIN) > 3•f(XCIN).
XCIN XCOUT
XIN
XOUT
(4) Low power dissipation mode
Rf
Rd
The low power consumption operation can be realized by stopping
the main clock XIN in low-speed mode. To stop the main clock, set
bit 5 of the CPU mode register to “1.” When the main clock XIN is
restarted (by setting the main clock stop bit to “0”), set sufficient
time for oscillation to stabilize.
COUT
CCIN
CCOUT
CIN
Fig. 52 Ceramic resonator circuit
The sub-clock XCIN-XCOUT oscillation circuit can not directly input
clocks that are generated externally. Accordingly, make sure to
cause an external resonator to oscillate.
Oscillation Control
(1) Stop mode
If the STP instruction is executed, the internal clock φ stops at an
“H” level, and XIN and XCIN oscillation stops. When the oscillation
stabilizing time set after STP instruction released bit is “0,” the
prescaler 12 is set to “FF16” and timer 1 is set to “0116.” When the
oscillation stabilizing time set after STP instruction released bit is
“1,” set the sufficient time for oscillation of used oscillator to stabi-
lize since nothing is set to the prescaler 12 and timer 1.
Either XIN or XCIN divided by 16 is input to the prescaler 12 as
count source. Oscillator restarts when an external interrupt is re-
ceived, but the internal clock φ is not supplied to the CPU (remains
at “H”) until timer 1 underflows. The internal clock φ is supplied for
the first time, when timer 1 underflows. This ensures time for the
clock oscillation using the ceramic resonators to be stabilized.
When the oscillator is restarted by reset, apply “L” level to the
X
CIN
X
COUT
X
IN
XOUT
Open
Rf
Rd
External oscillation
circuit
C
CIN
CCOUT
Vcc
Vss
Fig. 53 External clock input circuit
46
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec.H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
✽Notes on middle-speed mode automatic
switch set bit
b7
b0
MISRG
(MISRG : address 003816
)
When the middle-speed mode automatic switch set bit is set to “1”
while operating in the low-speed mode, by detecting the rising/fall-
ing edge of the SCL or SDA pin, XIN oscillation automatically starts
and the mode is automatically switched to the middle-speed
mode. The timing which changes from the low-speed mode to the
middle-speed mode can be set as 4.5 to 5.5 cycle, or 6.5 to 7.5
cycle in the low-speed mode by the middle-speed mode automatic
switch waiting time set bit. Select according to the oscillation start
characteristic of the XIN oscillator to be used.
Oscillation stabilizing time set after STP instruction
released bit
0: Automatically set “0116” to Timer 1,
“FF16” to Prescaler 12
1: Automatically set nothing
Middle-speed mode automatic switch set bit
0: Not set automatically
1: Automatic switching enable (Notes 1, 2)
Middle-speed mode automatic switch wait time set bit
0: 4.5 to 5.5 machine cycles
1: 6.5 to 7.5 machine cycles
Middle-speed mode automatic switch start bit
(Depending on program)
0: Invalid
1: Automatic switch start (Note 2)
Not used (return “0” when read)
Notes 1: While operating in the low-speed mode, the mode can be automatically
switched to the middle-speed mode by the SCL/SDA interrupt.
2: When the mode is automatically switched from the low-speed mode to
the middle-speed mode, the value of CPU mode register (address
003B16) changes.
Fig. 54 Structure of MISRG
XCOUT
XCIN
“0”
“1”
Port X
C
switch bit
XOUT
XIN
Timer 12 count source
selection bit
Main clock division ratio
selection bits (Note 1)
Low-speed mode
1/2
Prescaler 12
FF16
Timer 1
0116
1/4
1/2
Reset or
STP instruction
(Note 2)
High-speed or
middle-speed
mode
Main clock division ratio
selection bits (Note 1)
Middle-speed mode
Timing φ (internal clock)
High-speed or
low-speed mode
Main clock stop bit
Reset
Q
S
R
S
R
Q
Q
S
R
STP instruction
STP instruction
WIT instruction
Reset
Interrupt disable flag l
Interrupt request
Notes 1: Any one of high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register.
When low-speed mode is selected, set port Xc switch bit (b4) to “1”.
2: When bit 0 of MISRG = “0”
Fig. 55 System clock generating circuit block diagram (Single-chip mode)
47
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec.H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Reset
High-speed mode
(f(φ) = 4 MHz)
Middle-speed mode
(f(φ) = 1 MHz)
CM
6
“1” ←→ “0”
CM
CM
CM
CM
7
= 0
= 0
CM
CM
CM
CM
7
6
5
4
= 0
= 1
6
5
4
= 0 (8 MHz oscillating)
= 0 (32 kHz stopped)
= 0 (8 MHz oscillating)
= 0 (32 kHz stopped)
C
”
M
0
“
“
4
0
”
M4
”
C
←→
M
←→
0
“
C
“
6
1
”
”
1
“
M6
”
“
1
←→
←→
C
”
1
“
“
0
”
Middle-speed mode
(f(φ) = 1 MHz)
High-speed mode
(f(φ) = 4 MHz)
CM
6
“1” ←→ “0”
CM
CM
CM
CM
7
= 0
= 1
CM
7
6
5
4
= 0
= 0
6
5
4
CM
CM
CM
= 0 (8 MHz oscillating)
= 1 (32 kHz oscillating)
= 0 (8 MHz oscillating)
= 1 (32 kHz oscillating)
C
M
“
7
0
”
C
←→
M
“
6
1
”
“
1
←→
”
“
0
”
Low-speed mode
(f(φ)=16 kHz)
CM
CM
CM
CM
7
= 1
= 0
6
5
4
= 0 (8 MHz oscillating)
= 1 (32 kHz oscillating)
b7
b4
CPU mode register
(CPUM : address 003B16
)
CM
CM
CM
4
5
7
: Port Xc switch bit
0 : I/O port function (stop oscillating)
1 : XCIN-XCOUT oscillating function
: Main clock (XIN- XOUT) stop bit
0 : Operating
1 : Stopped
, CM
6: Main clock division ratio selection bits
Low-speed mode
(f(φ)=16 kHz)
b7 b6
CM
CM
CM
CM
7
6
5
4
= 1
= 0
0
0
1
1
0 : φ = f(XIN)/2 ( High-speed mode)
1 : φ = f(XIN)/8 (Middle-speed mode)
0 : φ = f(XCIN)/2 (Low-speed mode)
1 : Not available
= 1 (8 MHz stopped)
= 1 (32 kHz oscillating)
Notes
1 : Switch the mode by the allows shown between the mode blocks. (Do not switch between the modes directly without an allow.)
2 : The all modes can be switched to the stop mode or the wait mode and return to the source mode when the stop mode or the wait mode is
ended.
3 : Timer operates in the wait mode.
4 : When bit 0 of MISRG is “0” and the stop mode is ended, a delay of approximately 1 ms occurs by connecting timer 1 in middle/high-speed
mode.
5 : When bit 0 of MISRG is “0” and the stop mode is ended, the following is performed.
(1) After the clock is restarted, a delay of approximately 250 ms occurs in low-speed mode if Timer 12 count source selection bit is “0”.
(2) After the clock is restarted, a delay of approximately 16 ms occurs in low-speed mode if Timer 12 count source selection bit is “1”.
6 : Wait until oscillation stabilizes after oscillating the main clock XIN before the switching from the low-speed mode to middle/high-speed
mode.
7 : The example assumes that 8 MHz is being applied to the XIN pin and 32 kHz to the XCIN pin. φ indicates the internal clock.
Fig. 56 State transitions of system clock
48
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
NOTES ON PROGRAMMING
A-D Converter
Processor Status Register
The comparator uses capacitive coupling amplifier whose charge
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is “1.” Af-
ter a reset, initialize flags which affect program execution. In
particular, it is essential to initialize the index X mode (T) and the
decimal mode (D) flags because of their effect on calculations.
will be lost if the clock frequency is too low.
Therefore, make sure that f(XIN) in the middle/high-speed mode is
at least on 500 kHz during an A-D conversion.
Do not execute the STP instruction or the WIT instruction during
an A-D conversion.
Interrupts
Instruction Execution Time
The contents of the interrupt request bits do not change immedi-
ately after they have been written. After writing to an interrupt
request register, execute at least one instruction before perform-
ing a BBC or BBS instruction.
The instruction execution time is obtained by multiplying the fre-
quency of the internal clock φ by the number of cycles needed to
execute an instruction.
The number of cycles required to execute an instruction is shown
in the list of machine instructions.
Decimal Calculations
The frequency of the internal clock φ is half of the XIN frequency in
high-speed mode.
• To calculate in decimal notation, set the decimal mode flag (D)
to “1”, then execute an ADC or SBC instruction. After executing
an ADC or SBC instruction, execute at least one instruction be-
fore executing a SEC, CLC, or CLD instruction.
NOTES ON USAGE
Handling of Source Pins
In order to avoid a latch-up occurrence, connect a capacitor suit-
able for high frequencies as bypass capacitor between power
source pin (VCC pin) and GND pin (VSS pin) and between power
source pin (VCC pin) and analog power source input pin (AVSS
pin). Besides, connect the capacitor to as close as possible. For
bypass capacitor which should not be located too far from the pins
to be connected, a ceramic capacitor of 0.01 µF–0.1µF is recom-
mended.
• In decimal mode, the values of the negative (N), overflow (V),
and zero (Z) flags are invalid.
Timers
If a value n (between 0 and 255) is written to a timer latch, the fre-
quency division ratio is 1/(n+1).
Multiplication and Division Instructions
• The index X mode (T) and the decimal mode (D) flags do not af-
fect the MUL and DIV instruction.
EPROM Version/One Time PROM Version
The CNVss pin is connected to the internal memory circuit block
by a low-ohmic resistance, since it has the multiplexed function to
be a programmable power source pin (VPP pin) as well.
To improve the noise reduction, connect a track between CNVss
pin and Vss pin or Vcc pin with 1 to 10 kΩ resistance.
The mask ROM version track of CNVss pin has no operational in-
terference even if it is connected to Vss pin or Vcc pin via a
resistor.
• The execution of these instructions does not change the con-
tents of the processor status register.
Ports
The contents of the port direction registers cannot be read. The
following cannot be used:
• The data transfer instruction (LDA, etc.)
• The operation instruction when the index X mode flag (T) is “1”
• The addressing mode which uses the value of a direction regis-
ter as an index
Electric Characteristic Differences between
Mask ROM and One Time PROM Version
MCUs
There are differences in electric characteristics, operation margin,
noise immunity, and noise radiation between mask ROM and One
Time PROM version MCUs due to the differences in the manufac-
turing processes.
• The bit-test instruction (BBC or BBS, etc.) to a direction register
• The read-modify-write instructions (ROR, CLB, or SEB, etc.) to
a direction register.
Use instructions such as LDM and STA, etc., to set the port direc-
tion registers.
When manufacturing an application system with One Time PROM
version and then switching to use of the mask ROM version, per-
form sufficient evaluations for the commercial samples of the
mask ROM version.
Serial I/O
In serial I/O1 (clock synchronous mode), if the receive side is us-
ing an external clock and it is to output the SRDY1 signal, set the
transmit enable bit, the receive enable bit, and the SRDY1 output
enable bit to “1.”
Serial I/O1 continues to output the final bit from the TXD pin after
transmission is completed.
SOUT2 pin for serial I/O2 goes to high impedance after transmis-
sion is completed.
When an external clock is used as synchronous clock in serial
I/O1 or serial I/O2, write transmission data to the transmit buffer
register or serial I/O2 register while the transfer clock is “H.”
49
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM produc-
tion:
ROM PROGRAMMING METHOD
The built-in PROM of the blank One Time PROM version and buit-
in EPROM version can be read or programmed with a
general-purpose PROM programmer using a special programming
adapter. Set the address of PROM programmer in the user ROM
area.
✽
1. Mask ROM Order Confirmation Form
✽
2. Mark Specification Form
3. Data to be written to ROM, in EPROM form (three identical cop-
ies) or one floppy disk.
Table 13 Programming adapter
DATA REQUIRED FOR One Time PROM
PROGRAMMING ORDERS
Package
Name of Programming Adapter
44PJX-A
PCA7446
The following are necessary when ordering a PROM programming
service:
The PROM of the blank One Time PROM version is not tested or
screened in the assembly process and following processes. To en-
sure proper operation after programming, the procedure shown in
Figure 57 is recommended to verify programming.
✽
1. ROM Programming Confirmation Form
✽
2. Mark Specification Form (only special mark with customer’s
trade mark logo)
3. Data to be programmed to PROM, in EPROM form (three iden-
tical copies) or one floppy disk.
✽For the mask ROM confirmation and the mark specifications, re-
fer to the “Mitsubishi MCU Technical Information” Homepage
(http://www.infomicom.maec.co.jp/indexe.htm).
Programming with PROM
programmer
Screening (Caution)
(150 °C for 40 hours)
Verification with
PROM programmer
Functional check in
target device
The screening temperature is far higher
than the storage temperature. Never
expose to 150 °C exceeding 100 hours.
Caution :
Fig. 57 Programming and testing of One Time PROM version
50
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
ELECTRICAL CHARACTERISTICS
Table 14 Absolute maximum ratings
Symbol
Parameter
Power source voltage
Conditions
Ratings
Unit
V
VCC
–0.3 to 6.5
Input voltage P00–P07, P10–P17, P20, P21,
P24–P27, P30–P35, P40–P45,
VREF
VI
–0.3 to VCC +0.3
V
VI
VI
VI
Input voltage P22, P23
–0.3 to 5.8
–0.3 to VCC +0.3
–0.3 to VCC +0.3
–0.3 to 13
V
V
Input voltage RESET, XIN
All voltages are based on VSS.
Output transistors are cut off.
Input voltage
M37516M4H, M37516M6H
M37516E6H
V
V
Output voltage P00–P07, P10–P17, P20, P21,
P24–P27, P30–P35, P40–P45,
XOUT
VO
–0.3 to VCC +0.3
VO
Output voltage P22, P23
Power dissipation
–0.3 to 5.8
300
V
mW
°C
Pd
Ta = 25 °C
Topr
Tstg
Operating temperature
Storage temperature
–20 to 85
–40 to 125
°C
Table 15 Recommended operating conditions (1)
(VCC = 2.7 to 5.5 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Symbol
Parameter
Unit
V
Min.
Typ.
5.0
5.0
0
Max.
Power source voltage (At 8 MHz)
Power source voltage (At 4 MHz)
Power source voltage
4.0
2.7
5.5
5.5
VCC
VSS
VREF
AVSS
VIA
V
V
V
V
V
A-D convert reference voltage
Analog power source voltage
2.0
VCC
0
Analog input voltage
“H” input voltage
AN0–AN5
P00–P07, P10–P17, P20–P27, P30–P35, P40–P45
AVSS
VCC
VCC
VIH
0.8VCC
2
“H” input voltage (when I C-BUS input level is selected)
SDA1, SCL1
VIH
VIH
VIH
0.7VCC
0.7VCC
1.4
5.8
VCC
5.8
V
V
V
V
2
“H” input voltage (when I C-BUS input level is selected)
SDA2, SCL2
“H” input voltage (when SMBUS input level is selected)
SDA1, SCL1
“H” input voltage (when SMBUS input level is selected)
SDA2, SCL2
VCC
1.4
VIH
“H” input voltage
“L” input voltage
RESET, XIN, CNVSS
VCC
V
V
0.8VCC
0
VIH
VIL
P00–P07, P10–P17, P20–P27, P30–P35, P40–P45
0.2VCC
2
“L” input voltage (when I C-BUS input level is selected)
SDA1, SDA2, SCL1, SCL2
0.3VCC
0.6
0
0
V
V
VIL
VIL
“L” input voltage (when SMBUS input level is selected)
SDA1, SDA2, SCL1, SCL2
0.2VCC
0.16VCC
–80
–80
80
“L” input voltage
RESET, CNVSS
0
0
V
VIL
“L” input voltage
XIN
V
VIL
ΣIOH(peak)
ΣIOH(peak)
ΣIOL(peak)
ΣIOL(peak)
ΣIOL(peak)
ΣIOH(avg)
ΣIOH(avg)
ΣIOL(avg)
ΣIOL(avg)
ΣIOL(avg)
“H” total peak output current
“H” total peak output current
“L” total peak output current
“L” total peak output current
“L” total peak output current
P00–P07, P10–P17, P30–P35 (Note)
P20, P21, P24–P27, P40–P45 (Note)
P00–P07, P30–P35 (Note)
P10–P17 (Note)
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
120
80
P20–P27,P40–P45 (Note)
“H” total average output current P00–P07, P10–P17, P30–P35 (Note)
“H” total average output current P20, P21, P24–P27, P40–P45 (Note)
“L” total average output current P00–P07, P30–P35 (Note)
“L” total average output current P10–P17 (Note)
–40
–40
40
60
“L” total average output current P20–P27,P40–P45 (Note)
40
Note : The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured
over 100 ms. The total peak current is the peak value of all the currents.
51
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 16 Recommended operating conditions (2)
(VCC = 2.7 to 5.5 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Unit
Symbol
Parameter
Min.
Typ.
Max.
“H” peak output current
P00–P07, P10–P17, P20, P21, P24–P27, P30–P35,
P40–P45 (Note 1)
IOH(peak)
–10
mA
IOL(peak)
IOL(peak)
10
20
mA
mA
“L” peak output current
“L” peak output current
“H” average output current
P00–P07, P20–P27, P30–P35, P40–P45 (Note 1)
P10–P17 (Note 1)
P00–P07, P10–P17, P20, P21, P24–P27, P30–P35,
P40–P45 (Note 2)
–5
mA
IOH(avg)
IOL(avg)
IOL(avg)
f(XIN)
5
mA
“L” average output current
“L” peak output current
P00–P07, P20–P27, P30–P35, P40–P45 (Note 2)
P10–P17 (Note 2)
15
8
mA
MHz
Internal clock oscillation frequency (VCC = 4.0 to 5.5V) (Note 3)
Internal clock oscillation frequency (VCC = 2.7 to 5.5V) (Note 3)
f(XIN)
4
MHz
Notes 1: The peak output current is the peak current flowing in each port.
2: The average output current IOL(avg), IOH(avg) are average value measured over 100 ms.
3: When the oscillation frequency has a duty cycle of 50%.
52
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 17 Electrical characteristics
(VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Typ.
Symbol
Parameter
“H” output voltage
P00–P07, P10–P17, P20, P21,
P24–P27, P30–P35, P40–P45
(Note)
Unit
Test conditions
IOH = –10 mA
VCC = 4.0–5.5 V
IOH = –1.0 mA
VCC = 2.7–5.5 V
Min.
Max.
V
V
V
V
V
V
VCC–2.0
VCC–1.0
VOH
VOL
VOL
IOL = 10 mA
VCC = 4.0–5.5 V
IOL = 1.0 mA
“L” output voltage
P00–P07, P20–P27, P30–P35,
P40–P45
2.0
1.0
2.0
1.0
VCC = 2.7–5.5 V
IOL = 20 mA
VCC = 4.0–5.5 V
IOL = 10 mA
“L” output voltage
P10–P17
VCC = 2.7–5.5 V
Hysteresis
CNTR0, CNTR1, INT0–INT3
V
0.4
VT+–VT–
Hysteresis
RxD, SCLK
VT+–VT–
VT+–VT–
V
V
0.5
0.5
Hysteresis RESET
“H” input current
P00–P07, P10–P17, P20, P21,
P24–P27, P30–P35, P40–P45
VI = VCC
5.0
5.0
µA
IIH
µA
µA
IIH
IIH
“H” input current RESET, CNVSS
“H” input current XIN
VI = VCC
VI = VCC
4
“L” input current
P00–P07, P10–P17, P20–P27
P30–P35, P40–P45
µA
IIL
–5.0
–5.0
VI = VSS
µA
µA
V
VI = VSS
“L” input current RESET,CNVSS
IIL
VI = VSS
“L” input current
XIN
IIL
–4
When clock stopped
RAM hold voltage
VRAM
5.5
2.0
Note: P25 is measured when the P25/TXD P-channel output disable bit of the UART control register (bit 4 of address 001B16) is “0”.
53
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 18 Electrical characteristics
(VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Symbol
Parameter
Unit
Test conditions
High-speed mode
f(XIN) = 8 MHz
f(XCIN) = 32.768 kHz
Output transistors “off”
Typ.
Max.
13
Min.
6.8
mA
High-speed mode
f(XIN) = 8 MHz (in WIT state)
f(XCIN) = 32.768 kHz
Output transistors “off”
1.6
60
mA
Low-speed mode
f(XIN) = stopped
f(XCIN) = 32.768 kHz
Output transistors “off”
µA
200
40
Low-speed mode
f(XIN) = stopped
f(XCIN) = 32.768 kHz (in WIT state)
Output transistors “off”
20
µA
µA
Low-speed mode (VCC = 3 V)
f(XIN) = stopped
f(XCIN) = 32.768 kHz
Output transistors “off”
ICC
Power source
current
55
20
Low-speed mode (VCC = 3 V)
f(XIN) = stopped
f(XCIN) = 32.768 kHz (in WIT state)
Output transistors “off”
µA
5.0
10.0
Middle-speed mode
f(XIN) = 8 MHz
f(XCIN) = stopped
Output transistors “off”
4.0
1.5
7.0
mA
mA
µA
Middle-speed mode
f(XIN) = 8 MHz (in WIT state)
f(XCIN) = stopped
Output transistors “off”
Increment when A-D conversion is
executed
f(XIN) = 8 MHz
800
0.1
All oscillation stopped
(in STP state)
Output transistors “off”
µA
µA
Ta = 25 °C
1.0
10
Ta = 85 °C
54
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 19 A-D converter characteristics
(VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to 85 °C, f(XIN) = 8 MHz, f(XCIN) = 32 kHz, unless otherwise noted)
Limits
Symbol
Parameter
Test conditions
Unit
Min.
Typ.
Max.
10
–
–
Resolution
bit
Absolute accuracy (excluding quantization error)
Conversion time
±4
LSB
tc(φ)
tCONV
High-speed mode,
middle-speed mode
61
Low-speed mode
40
35
µs
kΩ
µA
µA
µA
RLADDER
IVREF
Ladder resistor
VREF “on” VREF = 5.0 V
VREF “off”
Reference power source input current
50
150
200
5.0
5.0
II(AD)
A-D port input current
0.5
55
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
TIMING REQUIREMENTS
Table 20 Timing requirements (1)
(VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Unit
Symbol
Parameter
Min.
20
Typ.
Max.
XIN cycles
ns
tW(RESET)
tC(XIN)
Reset input “L” pulse width
External clock input cycle time
125
50
ns
tWH(XIN)
External clock input “H” pulse width
External clock input “L” pulse width
CNTR0, CNTR1 input cycle time
ns
tWL(XIN)
50
ns
tC(CNTR)
200
80
ns
tWH(CNTR)
tWL(CNTR)
tWH(INT)
CNTR0, CNTR1 input “H” pulse width
CNTR0, CNTR1 input “L” pulse width
INT0 to INT3 input “H” pulse width
INT0 to INT3 input “L” pulse width
Serial I/O1 clock input cycle time (Note)
Serial I/O1 clock input “H” pulse width (Note)
Serial I/O1 clock input “L” pulse width (Note)
Serial I/O1 clock input set up time
Serial I/O1 clock input hold time
ns
80
ns
80
ns
tWL(INT)
80
ns
tC(SCLK1)
800
370
370
220
100
1000
400
400
200
200
ns
tWH(SCLK1)
tWL(SCLK1)
tsu(RxD-SCLK1)
th(SCLK1-RxD)
tC(SCLK2)
ns
ns
ns
ns
Serial I/O2 clock input cycle time
Serial I/O2 clock input “H” pulse width
Serial I/O2 clock input “L” pulse width
Serial I/O2 clock input set up time
Serial I/O2 clock input hold time
ns
tWH(SCLK2)
tWL(SCLK2)
tsu(SIN2-SCLK2)
th(SCLK2-SIN2)
ns
ns
ns
Note : When f(XIN) = 8 MHz and bit 6 of address 001A16 is “1” (clock synchronous).
Divide this value by four when f(XIN) = 8 MHz and bit 6 of address 001A16 is “0” (UART).
Table 21 Timing requirements (2)
(VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Typ.
Symbol
Parameter
Unit
Min.
20
Max.
XIN cycles
ns
tW(RESET)
tC(XIN)
Reset input “L” pulse width
External clock input cycle time
250
100
100
500
230
230
230
230
2000
950
950
400
200
2000
950
950
400
300
ns
tWH(XIN)
External clock input “H” pulse width
External clock input “L” pulse width
CNTR0, CNTR1 input cycle time
ns
tWL(XIN)
ns
tC(CNTR)
ns
tWH(CNTR)
tWL(CNTR)
tWH(INT)
CNTR0, CNTR1 input “H” pulse width
CNTR0, CNTR1 input “L” pulse width
INT0 to INT3 input “H” pulse width
INT0 to INT3 input “L” pulse width
Serial I/O1 clock input cycle time (Note)
Serial I/O1 clock input “H” pulse width (Note)
Serial I/O1 clock input “L” pulse width (Note)
Serial I/O1 clock input set up time
Serial I/O1 clock input hold time
ns
ns
ns
tWL(INT)
ns
tC(SCLK1)
ns
tWH(SCLK1)
tWL(SCLK1)
tsu(RxD-SCLK1)
th(SCLK1-RxD)
tC(SCLK2)
ns
ns
ns
ns
Serial I/O2 clock input cycle time
Serial I/O2 clock input “H” pulse width
Serial I/O2 clock input “L” pulse width
Serial I/O2 clock input set up time
Serial I/O2 clock input hold time
ns
tWH(SCLK2)
tWL(SCLK2)
tsu(SIN2-SCLK2)
th(SCLK2-SIN2)
ns
ns
ns
Note : When f(XIN) = 4 MHz and bit 6 of address 001A16 is “1” (clock synchronous).
Divide this value by four when f(XIN) = 8 MHz and bit 6 of address 001A16 is “0” (UART).
56
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 22 Switching characteristics 1
(VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Test conditions
Parameter
Symbol
Unit
Min.
Typ.
Max.
140
tWH (SCLK1)
tWL (SCLK1)
td (SCLK1-TXD)
tv (SCLK1-TXD)
tr (SCLK1)
Serial I/O1 clock output “H” pulse width
Serial I/O1 clock output “L” pulse width
Serial I/O1 output delay time (Note 1)
Serial I/O1 output valid time (Note 1)
Serial I/O1 clock output rising time
Serial I/O1 clock output falling time
Serial I/O2 clock output “H” pulse width
Serial I/O2 clock output “L” pulse width
Serial I/O2 output delay time (Note 2)
Serial I/O2 output valid time (Note 2)
Serial I/O2 clock output falling time
CMOS output rising time (Note 3)
CMOS output falling time (Note 3)
tC(SCLK1)/2–30
tC(SCLK1)/2–30
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
–30
30
30
tf (SCLK1)
Fig. 59
tWH (SCLK2)
tWL (SCLK2)
td (SCLK2-SOUT2)
tv (SCLK2-SOUT2)
tf (SCLK2)
tC(SCLK2)/2–160
tC(SCLK2)/2–160
200
0
30
30
30
tr (CMOS)
10
10
tf (CMOS)
Notes 1: For tWH(SCLK1), tWL(SCLK1), when the P25/TXD P-channel output disable bit of the UART control register (bit 4 of address 001B16) is “0”.
2: When the P01/SOUT2 and P02/SCLK2 P-channel output disable bit of the Serial I/O2 control register (bit 7 of address 001516) is “0”.
3: The XOUT pin is excluded.
Table 23 Switching characteristics 2
(VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Test conditions
Parameter
Symbol
Unit
Min.
Typ.
Max.
350
tWH (SCLK1)
tWL (SCLK1)
td (SCLK1-TXD)
tv (SCLK1-TXD)
tr (SCLK1)
Serial I/O1 clock output “H” pulse width
Serial I/O1 clock output “L” pulse width
Serial I/O1 output delay time (Note 1)
Serial I/O1 output valid time (Note 1)
Serial I/O1 clock output rising time
Serial I/O1 clock output falling time
Serial I/O2 clock output “H” pulse width
Serial I/O2 clock output “L” pulse width
Serial I/O2 output delay time (Note 2)
Serial I/O2 output valid time (Note 2)
Serial I/O2 clock output falling time
CMOS output rising time (Note 3)
CMOS output falling time (Note 3)
tC(SCLK1)/2–50
tC(SCLK1)/2–50
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
–30
50
50
tf (SCLK1)
Fig. 59
tWH (SCLK2)
tWL (SCLK2)
td (SCLK2-SOUT2)
tv (SCLK2-SOUT2)
tf (SCLK2)
tC(SCLK2)/2–240
tC(SCLK2)/2–240
400
0
50
50
50
tr (CMOS)
20
20
tf (CMOS)
Notes 1: For tWH(SCLK1), tWL(SCLK1), when the P25/TXD P-channel output disable bit of the UART control register (bit 4 of address 001B16) is “0”.
2: When the P01/SOUT2 and P02/SCLK2 P-channel output disable bit of the Serial I/O2 control register (bit 7 of address 001516) is “0”.
3: The XOUT pin is excluded.
57
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
2
MULTI-MASTER I C-BUS BUS LINE CHARACTERISTICS
2
Table 24 Multi-master I C-BUS bus line characteristics
Standard clock mode
High-speed clock mode
Symbol
Parameter
Unit
Min.
4.7
Max.
Max.
Min.
1.3
tBUF
µs
µs
µs
ns
µs
µs
ns
ns
µs
µs
Bus free time
tHD;STA
tLOW
0.6
1.3
Hold time for START condition
Hold time for SCL clock = “0”
Rising time of both SCL and SDA signals
Data hold time
4.0
4.7
tR
20+0.1Cb
0
300
0.9
1000
300
tHD;DAT
tHIGH
tF
0
Hold time for SCL clock = “1”
Falling time of both SCL and SDA signals
Data setup time
4.0
0.6
20+0.1Cb
100
300
tSU;DAT
tSU;STA
tSU;STO
250
4.7
4.0
Setup time for repeated START condition
Setup time for STOP condition
0.6
0.6
Note: Cb = total capacitance of 1 bus line
SDA
t
HD:STA
t
su:STO
t
BUF
t
LOW
t
R
tF
P
Sr
S
P
SCL
t
HD:STA
t
HD:DAT
t
HIGH
tsu:DAT
t
su:STA
S : START condition
Sr: RESTART condition
P : STOP condition
2
Fig. 58 Timing diagram of multi-master I C-BUS
58
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Measurement output pin
100pF
CMOS output
Fig. 59 Circuit for measuring output switching characteris-
tics (1)
59
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
tC(CNTR)
t
WH(CNTR)
t
WL(CNTR)
CNTR
CNTR
0
1
0.8VCC
0.2VCC
0.2VCC
tWL(INT)
tWH(INT)
0.8VCC
INT0
to INT
3
tW(RESET)
0.8VCC
RESET
0.2VCC
tC(XIN)
tWL(XIN)
tWH(XIN)
0.8VCC
X
IN
0.2VCC
t
C(SCLK1),
t
C(SCLK2)
t
WL(SCLK1),
tWL(SCLK2
)
t
WH(SCLK1), WH(SCLK2)
t
t
r
tf
S
S
CLK1
CLK2
0.8VCC
0.2VCC
t
t
h(SCLK1
-
-
RxD),
t
t
su(R
x
D
-
S
CLK1),
CLK2
h(SCLK2
S
IN2)
su(SIN2
-
S
)
R D
X
0.8V
0.2VCCCC
S
IN2
t
t
d(SCLK1-T
XD),
t
t
v(SCLK1-T
XD),
d(SCLK2-SOUT2
)
v(SCLK2-SOUT2
)
TXD
SOUT2
Fig. 60 Timing diagram
60
MITSUBISHI MICROCOMPUTERS
7516 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Keep safety first in your circuit designs!
•
Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable
material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
•
•
•
These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property
rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party.
Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples
contained in these materials.
All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by
Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product
distributor for the latest product information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com).
When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision
on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein.
Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric
Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical,
aerospace, nuclear, or undersea repeater use.
•
•
•
•
The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials.
If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved
destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
•
Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
© 2002 MITSUBISHI ELECTRIC CORP.
New publication, effective Oct. 2002.
Specifications subject to change without notice.
REVISION HISTORY
7516 GROUP (SPEC. H) DATA SHEET
Rev.
Date
Description
Summary
Page
1.0 10/21/02
First Edition
(1/1)
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明